GE(W)/HSR-16/2023-24 REPAIR/ REPLACEMENT AND OTHER MISC WORK OF BOUNDARY WALL OF ZONE B AT HISAR MIL STN UNDER GE (W) HISAR

Amount

Demolition Brick work built in cement mortar or cement lime mortar completed all as specified and directed.

M & L brick work with Sub Class 'B' bricks straight or curved on plan exc 6.0m mean radius built in cm 1:4 completed all as specified and directed.

All as per item No 2.00 above but except bricks completed all as specified and directed.

Taking down cement plaster on brick/stone or concrete surfaces including racking out joints, hacking for key,scrubbing down with water to receive plaster, including removal rubbish outside MOD land ect complete all as specified and directed .

M & L rendering 15mm thick on fair faces of brick work in CM 1:4 finished even & smooth without using extra cement completed all as specified and directed.

M&L rough cast plaster as specified (rendering coat not less than 10mm thick in CM 1:3 while it is stil in plastic state the rough cast mixture consisting of cruhed stone or fine gravel aggregate size 6to12mm mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished evevn on external wall upto cill height complete all as specified and directed.

M&L for preparation of newely plastered surfaces of walls and applying two coats of cement based paint over a coat of primer complete all as specified and directed.

Preparing old plastered or unplastered surfaces of walls and applying two coats of cement base paint completed all as specified and directed.

M & L two coat of weather coat paint over a coat of primer on new surfaces of walls including preparation of surfaces completed all as specified and directed.

M & L Complete removal of existing treatment old surface of wall and applying two coat of weather proof paint completed all as specified and directed.

S&F Wire netting of galvanized steel wire 0.91 mm dia fixed with tinned tacks of wire staples size of mesh 20 mm as in wall plaster repair works completed all as specified and directed.

Providing cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate in coping,benching and the like, including weathering slighthy rounded or chamfered angles and throating as directed including necessary form work completed all as specified and directed.

M&L of precast cement concrete louvres and jallies, 25mm thick Type Bo 1:2:4 (12.5mm graded agg.)(measured solid) in repair, including all mould but excluding frame Set in CM 1:4 in repair completed all as specified and directed.

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in soft/loose soil completed all as specified and directed.

Excavating in trenches, exceeding 1.5m but n exc 3 m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in soft/loose soil completed all as specified and directed.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each completed all as specified and directed.

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point completed all as specified and directed.

Demolition and breaking up drain pipes (salt glazed ware or RCC or PVC) set in cement mortar 150 mm dia complete all as specified and directed.

Demolition and breaking up drain pipes (salt glazed ware or RCC or PVC) set in cement mortar 200mm dia complete all as specified and directed.

Demolition and breaking up drain pipes (salt glazed ware or RCC or PVC) set in cement mortar 250mm dia complete all as specified and directed.

S&F 150 mm dia(6") PVC pipe of working pressure of 4 kg/cm2 single socketed in any length and joining pipes with adhesive solution in laid in trenches or in floors complete all as specified and directed.

S&F 200 mm dia(8") PVC pipe of working pressure of 4 kg/cm2 single socketed in any length and joining pipes with adhesive solution in laid in trenches or in floors complete all as specified and directed.

S&F 250 mm dia(10") PVC pipe of working pressure of 4 kg/cm2 single socketed in any length and joining pipes with adhesive solution in laid in trenches or in floors complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate for concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested complete for 150mm dia pipe complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate for concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested complete for 200mm dia pipe complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate for concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested complete for 250mm dia pipe complete all as specified and directed.

Cutting into existing manholes for connecting new drains, any dia bore, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required completed all as specified and directed.

Demolition of reinforced Concrete of any description and in any position not otherwise specifically provided completed all as specified and directed.

M&L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter completed all as specified and directed.

M&L RCC M-20(Nominal Mix) in slabs supported on walls, beams and columns completed all as specified and directed.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips completed all as specified and directed.

S&F TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders completed all as specified and directed.

Dismantling laied bedded and pointed in cement motar Stone slabs and tiles of any description or thickness in floors,walls etc completed all as specified and directed.

M& L 20 mm thick Granite of any type work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar 10 mm thick (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite completed all as specified and directed.

M& L 20 mm thick Dholpur pink stone (size 30 cm x 60 cm) pillars or walls in cement mortar 10 mm thick (1:4) including pointing in white cement (1:2) using stone dust with admixture of pigment to match with shade of pink dholpur stone and stainless steel studs minimum two nos for one tile complete all as specified and directed. Note :- 1. Height of fixing of stone up to 12 mtr. 2. Stainless steel studs to be measured and paid on respective item.

S & F Stainless steel studs (size- 4 mm dia and 75 mm long) for fixing Dholpur stone on wall completed all as specified and directed.

Dismantling wrought iron or mild steel work of any description completed all as specified and directed.

M&L Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete of Fe 410-W (Gde -E-250) quality-A fixed completed all as specified and directed.

Dismantling posts or struts (wood, steel or RCC) any section, including taking out embeded portion and making good distrubed ground posts embedded in concrete, brick work, masonry etc completed all as specified and directed.

Excvation in post holes each n.exc 0.50 cum getting out returning filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25mm watering and removing surplus soil to a distance n.exc 50m and making good in any type of soil completed all as specified and directed.

S&F angle iron post and struets in fencing including cutting tops to shape as directed, drilling holes, notching for wire including all necessary drilling bolting and reveting works confirming to Fe 290, grade E-165 completed all as specified and directed.

All as per item No 42.00 above but except steel fixing only completed all as specified and directed.

Dismantling fencing wire mesh any type and in any position completed all as specified and directed.

Supply only chain link mS galvanised fencing incld line wire, any mesh, any size any type of standard, staining bolt etc incld provn of bending wire completed all as specified and directed.

Fixing only chain link wire mesh as in chain link fencing completed all as specified and directed.

Dismantling barbed wire any type and in any position completed all as specified and directed.

S&F galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia bors at 75mm spacing and straining and fixed to any type of standard rails straining both including securing or tying at crossing with and provision of galvanised mild steel wire staples or steel pins etc completed all as specified and directed.

All as per srl item No 47.00 above but fixing only in repairs completed all as specified and directed.

S & F mild steel bars 10 mm dia as in chain link fencing completed all as specified and directed.

S & F 10mm dia 40mm long MS screw bolt machine made with hexagonal or Square head at one end and screwed the other,screwed end fixed with washer completed all as specified and directed.

M & L cement concrete in fdn filling and mass concrete type C-2 1:3:6 (40 mm graded aggregate) in post holes completed all as specified and directed.

M & L Painting steel surface of any description over 10 cm width and girth including preparation, primer with red oxide and two coats of synthetic enamel paints.

M&L for repairs of existing steel rolling shutter of size exc 15 sqm and not exc 30 sqm each by greasing of all mechanical parts and repair of springs, bevel gear box, crank handle, top cover, anchoring rod, hasp and staple, steel frame tightening all as required and fixing the shutter in existing postion and make rolling shutter fully functional including applying two coats of synthetic enamel paint including preparation of old steel surfaces completed all as specified and directed.

M&L for repair of existing Steel rolling shutters of size exc exc 30 sqm by greesing of all mechanical parts and repair of springs,bevel gear box, crank handle, top cover, anchoring rod, hasp and staple,steel frame tightning as required and fixing in existing position inclu two coat of synthetic enamel paint ; erected in position as indicated, completed all as specified and directed.

M&L for repairs existing steel openable shutter of size exc 15.00 Sqm to not exc 30 sqm each by greasing of all mechanical parts and repair of springs, top cover, anchoring rod,,side cover,shutter patti, lock plate, ear plate steel frame tightening all as required and fixing the shutter in existing postion and make openable shutter fully functional including applying two coats of synthetic enamel paint including preparation of old steel surfaces completed all as specified and directed.

M&L for repair of existing garrage gate/door/rolling shutter of size exc 30 sqm but not exceeding 45 Sqm by greesing of all mechanical parts and repair of holdfast/hinges,sliding bolt, handle, repair lower portion of door, welding work, etc steel frame tightening all as required and fixing the gate in existing postion and make openable gate/door fully functional including applying two coats of synthetic enamel paint including preparation of old steel surfaces completed all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors,aprons laid, bedded and pointed in any mortar etc completed all as specified and directed.

M&L 75mm thick PCC 1:3:6 type D2 using 40mm graded stone aggregate as in sub base of floors completed all as specified and directed.

Renewing cement concrete tiles 25mm thick of Size 300mm X 300mm in patches, area in exc 5 sq.m. including removing old tiles, preparing beds and laying or setting over 20mmthick screed bed of CM(1:4), jointing and pointing new or old tiles complete. Note - If new tiles are required at site for repair during execution of work, the qty of new tiles will be measured and paid separately uner supply only item completed all as specified and directed.

Supply only concrete cheaquere cement concrete tiles 30 cmx30 cmx25 mm thick wiith pigment chemichally treated heavy duty complete all as specified and directed.

M&L for chequered cement concrete tiles chemically treated,mechanicaly machine pressed, heavy duty of size 30cmx30cmx25 mm thick set jinted an pointed in neat cement slurry ith grey cement and with pigments in floor complete all as specified over and including 15 mm thick screed bed in CM 1:4 completed all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks,lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required completed all as specified and directed.

Panting of kerb stone in new or previously untreated surface with white/black paint any descripation of one coat of primer over two coat synthetic enamal paint of over 10 cm grith (or) width completed all as specified and directed.

Panting of kerb stone in old surface with white/black paint any descripation of one coat of synthetic enamel paint of over 10 cm grith (or) width completed all as specified and directed.

M&L for Painting lines, dashes, arrows, letters,etc. on roads, pavements and the like exc 10cm wide with Thermoplastic paint 2mm thick with glass beading for reflaction paint, white or golden yellow complete all as specified and directed.

B B BUILDERS

M/S RR ENGINEERING CO

VIKAS INFRASTRUCTURE

m/s krishna engineers1

Shiva Constructin Co.

SHRI HARI BUILDERS