SPECIAL REPAIR TO BLDG NO P-170 (JCO MD ACCN) AT CHETAK LINE IN UDAIPUR MILITARY STATION

Amount

Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness below or above ground level and removing material from site complete all as specified and directed.

Taking down chowkats or frames area not exceeding 1.50 Sqm (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good in cement mortar (1:3) or PCC 1:2:4 type B1, complete all as specified and as directed. (Note – The quoted rate shall be deemed to include for fixing of hold fast in the same opening irrespective of position of hold fasts and no separate item for making good of hold fasts jamb/cill/ bottom shall be paid).

Taking down chowkats or frames area exceeding 1.50 Sqm and not exceeding 4.00 Sqm (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good in cement mortar (1:3) or PCC 1:2:4 type B1, complete all as specified and as directed. (Note – The qouted rate shall be deemed to include for fixing of hold fast in the same opening irrespective of position of hold fasts and no separate item for making good of hold fasts jamb/cill/ bottom shall be paid).

Taking down shutters of any description not exceeding 1.00 Sqm each, from chowkhat complete all as specified.

Taking down shutters of any description exceeding 1.00 Sqm but not exceeding 2.00 Sqm each, from chowkhat complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

Material & Labour for Non - skid White Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Material & Labour for double charged vitrefied colour Ceramic tiles 8 to 10 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and inted in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed. Make : Johnson Marbonite/ Kajaria/ Somany

All as per above but in skirting to walls including 10mm thick cement plaster in cement mortar 1:4 as backing coat on fair faces on stone surface all as specified and directed. Make : Johnson Marbonite/ Kajaria/ Somany

Material & Labour for White Glazed ceramic tiles in vertical surface 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick cement plaster in ement mortar 1:4 as backing coat on fair faces on stone surface all as specified and directed. Make : Johnson Marbonite/ Kajaria/ Somany

Material & Labour for Green Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, corner shelves (300 x 300mm) and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following types and including 15mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces and half nose moulding (bull nosing) etc, complete all as specified and directed.

Material and labour for machine cut mirror polished Kota stone slab 20-22 mm thick (of size not less than 55 cm x 55 cm in flooring laid and jointed with grey cement slurry mixed with pigment to match shade of the slab including half round edge moulding, over and including cement screed bed 15 mm thick in cement mortar (1:6) base including rubbing and mirror polishing, and half nose moulding (bull nosing) etc,complete all as specified.

Material & Labour for machine cut Prepolished Kota stone slab 20-22 mm thick (of length not less than 55 cm in skirting and 120 cm in risers) laid and jointed with grey cement slurry mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing (Granite finish) but as in vertical surfaces such as skirting and risers over and including 10mm thick plaster in cement mortar (1:4) on brick work or concrete surfaces, complete all as specified.

Material & Labour for 75 mm thick Cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection with fair finished complete. Note : Joints 12 mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection.

Supply and fixing for mild steel framed work as in door chowkats/gate of angle or angle iron work as in fixing of cooler stand, ladder by drilling/cutting the stone masonry wall and fixing up to 1st floor walls, other section of grade Fe-290-Gde E-165 with gusset plate rails, braces etc welded/drilled to fixing of steel sheeting or other covering doors etc. to be prepared for sliding or hanging with and including either hooks and hinges or steel hanging door fittings (exclusive steel sheeting or other covering, running rails & guides), complete all as specified and as directed by the Engr-in-Charge.

Supply and fixing, made 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 65 mm x 125 mm (moulded) having single rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by "Rajshri/Echon or Eq" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings as directed,. Material test certificate and authentication should be compoulsory provided by the manufacturing company.

Supply & Fixing for 2nd class hard wood 35mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete.

Supply and fixing IInd class (hollock) hard wood factory made 35mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and directed.

Supply and fixing, made 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 45 mm x 90 mm (moulded) having single rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by "Rajshri/Echon or Eq" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings as directed,. Material test certificate and authentication should be compoulsory provided by the manufacturing company.

Supply & Fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N / m2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fie retardant WPC to be laminated with PVC foil of minimum 14 micron thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engr-in-Charge. (Note : Stainless steel butt hinges and necessary SS screws shall be paid separately).

Supply & fixed 200 mm long aluminium anbodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

Supply & fixed 150 mm long Extruded aluminium alloy handles, fabricated type anodised complete all as specified.

Supply & fixed 100 mm butt hinges, medium weight cold rolled mild steel and fixed complete all as specified and directed.

Supply & Fixing 100 mm long stainless steel butt hinges with galvanised MS hinge pin etc.

Supply & Fixing alluminum alloy, anodised, cast type or extruded section, sliding door bolt with hasp & staple (bolt type) with fixing clips and bolts and 300 mm long complete all as specified.

Supply & Fixing double legged door stopper of overall length of cover plate 150 mm of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floors and rubber all as specified and directed by Engr-in-charge.

Supply & Fixed in repairs aluminium Hat and coat hooks, solid body, 175mm to 250 mm

Supply & fixed MS helical door spring 150 mm long fixed with screws to wooden chowkhats or fixed with welding to steel chowkhats.

Supply and fixing factory made uPVC coloured Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead /double glazing bead of appropriate dimension. comprising of uPVC multi chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. (Make: Rajsri/ Fenesta/AIS or Eq.)

Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames, glazed with putty or fixed with beads.

Supply and fixing for 5.5 mm thick sheet glass, ordinary quality and glazing with oil putty in square not excc 0.5 Sqm in each pane complete all as specified and as directed by the EIC.

Supply and fixing stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staple or fixing with beads to wooden joinery when fixed in panels of joinery, complete all as specified.

Supply and fixing (in repair) stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks or galvanized wire staple and including fixing with beads supplied with joinery when fixed in panels of joinery, complete all as specified.

Material & Labour 18/19mm thick block board ,grade 2 quality interior grade , commercial type fixed with screw to timber frame work including taking down complete all as specified and directed.

Material & Labour Decorative laminate type 1 of 0.9 mm thick surface finish, colour and pattern as approved, fixed with approved adhesive as manufacturer's complete all as specified and directed.

Supply & fixed Continious piano hinges, continuous type of mild steel bright finish or electro galvanized with width of flap (when open) 30mm complete all as specified.

Supply & fixed 75mm long Brass handle, cast type, polished bright fixed with nut and screws to cupboard shutter complete all as specified and directed.

Supply & fixed magnetic ball catches with 8mm dia steel ball brass body and striking plate including letting in and fixed, complete all as specified.

Supply & fixed Powder coated aluminium ventilator fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary jointing cleats, glazing clip,rubber packing, anodised aluminium snap beading, screw etc complete all as specified.

Supply & fixed for anodised aluminium grill of (anodised transparent or dyed to required shade according to IS:1868 with minomum anodic coating of grade AC 15) of approved design/ pattern, with approved standard section and fixed to the existing window frame with C.P. brass / stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised alumiinium standard section around the opening, all complete as per reuirement and direction of Engineer incharge.

Supply & fixed steel for 4mm thick figured glass, ordinary quality and glazing rubber beading in square nexc 0.5 sqm in each pane complete.

Supply & fixing in repairs stainless steel type curtain rod 22 to 25mm dia as per sample.

Supply & fixing of purpose made brackets trade pattern for stainless steel decorative type curtain rods suitable for holding 22 to 25mm dia as per sample as in repair.

Supply & fixing of stainless steel decorative fincals(round type with mirror optic finish)trade pattern for decorative type curtain rods suitable for 22 to 25mm dia curtain rods as per sample as in repaie complete all as specified.

Supply & fixing of stainless steel decorative fincals wall to wall trade pattern suitable for decorative type curtain rods 22 to 25mm dia as per sample as in repair complete all as specified.

Material & labour for fabrication of pressed steel cupboard shutter using 1mm thick MS plain sheet with frame 1.25mm thick bent to shape including two coat of synthetic enamel paint on internal surfaces & two coat of hammer tone finish on external surface alongwith locking arrangement mortice lock with handle(make : Godrej) etc complete all as specified as per drg No CEJZ/TD/12/2008 sheet 1/3 to 3/3.

Taking down cement plaster from brick walls/stone masonry walls, concrete surfaces including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and as directed.

Material and labour for 15mm thick rendering in cement mortar (1:6) on brick/stone masonry or concrete surfaces (internal walls) of any description, finished the surface even and smooth without using extra cement complete all as specified.

Material and Labour for 15mm thick rendering on fair faces of brick work/stone masonry, concrete surfaces (external walls) or stone walls upto tripple storey bldgs in cement mortar 1:4 mixed with liquid water proofing compound using as per manufacturer’s instructions, finished even and fair, complete all as specified. Note : (i) WPC shall be measured and paid separately. (ii) Rendering upto 9 mtr ht shall be included in the quoted rate).

Material and labour 10 mm thick cement plaster in cement mortar 1:3 on ceiling, finished even and smooth without using extra cement all as specified and directed.

Supply only liquid water proofing compound, ISI marked complete all as specified and directed.

Material & Labour for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper (acrylic) white or tinted over a coat of 2 mm thick wall care putty, complete all as specified and directed.

Material & Labour for preparation of new plastered surfaces of wall and applying two coats of weather coat over a coat of 2 mm thick wall care putty for neat and smooth finishing complete all as specified.

Material & Labour for preparing new plastered surfaces and applying two coats of oil bound distemper (acrylic) white or tinted over a coat of 2 mm thick wall care putty on ceiling complete all as specified and directed.

Material & Labour for preparation of old plastered or un-plastered surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coat of oil bound distemper (acrylic) white or tinted over a coat of priming over a coat of 2mm thick wall care putty on walls upto tripple storeys bldg complete all as specified and directed.

Material & Labour for preparation of old plastered or un-plastered surface including complete removal of existing treatment, brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coat of weather coat over a coat of 2 mm thick wall care putty for neat and smooth finishing complete all as specified.

Material and labour for preparation of old Plastered or un-plastered surfaces of ceiling by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying one coat of oil bound distemper (acrylic) white or tinted over a coat of 1 mm thick wall care putty complete all as specified.

Material & Labour for preparation of old painted surfaces of wood and wood based surfaces of any description, over 10cm in width or girth and apply one coat of synthetic enamel paint complete all as specified and directed.

Material & Labour for preparation of old painted steel surface of any description, over 10cm in width or girth not other wise described and applying one coat of synthetic enamel paint complete all as specified and directed.

Material & Labour for two coat of synthetic enamel painting to new wood surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of pink primer complete all as specified and directed.

Material & Labour for two coat of synthetic enamel painting to new steel surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of red oxide primer complete all as specified and directed.

Supplying & laying 03 coats of reinforced acrylic coating ‘New Coat’ as on sunken floor applied @1.5 Ltr/Sqm in 03 coats to achieve total 1mm thickness in any position including cleaning surface of sunken slab with wire brush/mechanical brush and with water thoroughly to remove all dust/dirt and loose particles to expose base concrete/sunken slab etc including repairing of loose/defective joints and applying 15mm thick plaster in CM 1:3 to level the surface and treatment to be applied all as per manufacturers instructions, complete all as specified and directed.

Material & labour for PCC 1:2:4 type B-1 ( using 20mm graded mechanically crushed stone aggregate) as in bed blocks, copings, apex stones,side of interlocking tiles etc complete all as specified and directed.

Material & labour for 50 mm thick PCC 1:2:4 type B-1, (20mm graded aggregate) as in sunken floor complete all as specified and directed

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of steel reinforcement as required to facilitate demolition, complete all as specified.

Material and labour for providing reinforced cement concrete 1:2 :4 type B1 using (20mm graded stone aggregate ) as in cooking platform slab supported on wall, beam, cantilevers and kitchen cooking platform including necessary formwork complete all as specified.

Material and labour for repair to RCC (1:2:4) type B-1 using 20 mm graded stone aggregate as in chajjas, beams, column etc upto tripple storey bldgs including necessary formwork complete all as specified and directed.

Material and labour mild steel TMT bars, 8 mm dia , cut to length, bent to shape required including cranking, binding spirally for hooping or column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

Demolition of cement concrete in any position not other wise specifically provided for roof padding etc.

Material and Labour for PCC 1:2:4 type B-0 using (12.5 mm graded stone aggregate) as in padding on roof top including WPC as per manufacturers instructions to achieve the slop required, with minimum thickness of 25mm consolidated and finished even and fair without using extra cement. (WPC shall be measured and paid separately

Material & Labour for 10 mm thick screed bed or bedding layer in CM 1:3 mixed with water proofing compound as per manufacturer instructions on concrete roof surface finished fair and even on roof surface etc complete all as specified and directed.

Material & Labour for Providing water proofing treatment over cleaned roof surface with super thermo APP modified water proofing memberane comprising of the following for Non Approachable roofs:-

Cleaning of plastered roof surfaces and applying a coat of bitumen primer @ 0.40 Ltr/Sqm on top of dry surface of finished cement mortar plaster. One coat of hot blown bitumen of grade 85/25 @ 1.2kg /sqm shall be applied over primed surfaces and applying 3mm thick APP modified polymeric membrane with non woven polyster renforcement shall be laid. The side overlaps shall be min 75mm and the end laps shall be min 100mm. All overlaps and joints shall be sealed by flame all as specified and directed by Engr-in-Charge. Applying two coats of aluminum paint on top of membrane @ 0.10Kg/Sqm.

Material & Labour for 10mm thick rendering on concrete surfaces of roof projection cornices & chajja etc finished fair and even without using extra cement including WPC in CM 1:4 incl taking down existing cement plaster and including necessary arrangements to work on roof projection, cornice & chajja etc.

Material & Labour 100mm thick PCC type D-2, (1:4:8) using 40mm graded stone aggregate as in sub base complete all as specified and dirrected.

Supply and fixing for PCC coloured interlocking (glossy finishing lacquer coated) paver blocks confirming to IS-15658-2006 of 60 mm thickness, M-35 grade as in hardstanding etc. laid over and including 50 mm thick screed or bedding layer of sand, complete all as specified.

Supply & fixed 50mm bore LDPE (Low density Polyethylene Pipes) of pressure rating 6Kgf/Sqcm fixed complete to walls,ceilings or in floors including taking down of old GI tubing, 40 mm bore all as specified and directed.

Supply & fixed Polymer coloured (Polypropeylene Delrin and ABS) low level flushing cistern 10 Ltr capacity, valveless syphonic action type complete with inlet ball valve float valve bends brackets, rawl plug, brass screws handle etc complete having BIS derscription mark with 2731 with and including suitable size of MS brackets, plug, screws all as required incl taking down existing high level/low level flushing cistern any type disconnecting pipes and jointing with new one etc and making good the floors/walls as per existing floor finish/wall finish including 32 mm bore PVC flush pipe and jointing with Water closet of any type complete all as specified and directed. Make : CERA/ Parryware/ Jaquar

Supply & fixed in repair vitreous china wash hand basin flat back white of size 550mmx400mm with 32 mm dia chromium plated waste coupling including flush pipe etc complete all as specified. Make : CERA/ Parryware/ Jaquar

Supply and fixing , vitreous China squatting pan of Orrisa pattern size 580mmx440mm white (Ist quality) with ‘P’ or ’S’ trap, front or back inlet and integral foot rests of any pattern complete including provision of lime concrete bedding, trap and connection to flush pipe complete all as specified. Make : CERA/ Parryware/ Jaquar

Supply & fixed in repairs stainless steel sink with drainage board , made out of 1.00mm thick sheet for kitchen with plug,washers, waste pipe, CP waste coupling, cast iron cantilever bracket of overall size 915x460mm bowl size 410x330x160mm complete all as specified. Make : Jayna/ Nirali/ Parryware

Supply & fixed in repair stainless steel plate rack made out of 1.00mm thick sheet 900x900x200mmcomplete all as specified.

Supply and fixing in repairs,15mm bore pillar tap, fancy type, half turn chromium plated cast copper alloy with capstan head, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks , compete all as specified. Make : CERA/ Jaquar/ Prayag

Supply and fixing in repair, bib tap screwed down high pressure, cast copper alloy, chromium plated half trun fancy type, ISI marked, with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified. Make : CERA/ Jaquar/ Prayag

Supply & Fixing in repair 15mm bore concealed stop valve type chromium plated cast copper alloy screwed down high pressure screwed both ends for iron pipe or for union all as specified and directed by Engr-in-charge. Make : CERA/ Jaquar/ Prayag

Supply & Fixing in repair brass chromium plated tubular towel rail 20mm dia 'D' type 60cm long between flanges all as specified and directed by Engr-in-charge.

Supply & Fixing in repair rotational molded polyethylene water storage tanks (cylindrical vertical with closed top) capacity 500 Ltr hoisted and fixed in position after dismantling (water tank of cap exc 250 ltr and n.exc 500 ltr) and removing to store and all as specified and directed by Engr-in-charge.

Supply & Fixing in repair gun metal gate valves, with iron wheel head, screwed both ends for iron pipe flange ends type fixed of 20mm dia all as spd and directed.

Supply & Fixing in repair PTMT ball valves high pressure with epoxy coated aluminium rod & high density plastic ball screwed for 20mm bore pipes all as specified and directed by Engr-in-charge.

Taking up or down steel tubing and connections of 15mm bore complete all as required at site.

All as item above but 20mm bore, complete all as specified.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings 16mm dia bore on walls/ceiling or laying in floors or fixing as in concealed to walls or in floors etc, and making good the surfaces matching to exsiting surfaces of walls/ floor to the entire satisfaction of Engineer-in-charge.

Material & Labour Steel Tubes 20mm bore, 'medium grade', galvanised, with all fitting; laid in trenches and fixed complete to brick/stone wall or laid in floor concealed, complete all as specified and as directed.

Refixing old steel tubing of 20mm bore and connections in new or old position (Walls, ceiling, floors, etc.

Supply and fixing (in repair) stop valves, 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified. (Note : Weight of cock shall not be less than 0.575kg)

Supply and fixing (in repair) angle cock 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified. (Note : Weight of cock shall not be less than 0.575kg)

Supply & fixed in repair PVC connections 45cm long including 15mm bore PTMT nuts on both ends complete all as specified.

Supply & fixed in repairs stainless steel grating openable 100mm dia without hole including fixing with white cement complete all as specified.

Supply & fixed in repair fancy type shower rose125mm dia size of Rim and 30cm long CP brass pipe with swiwel joint complete all as specified. Make : CERA/ Jaquar/ Prayag

Supply & fixed in repair glass shelf assembly consisting of made out of 5.5 mm thick glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. Make : CERA/ Jaquar/ Prayag

Supply & Fixing for CP brass Soap Dish Holder, complete all as specified and as directed. Make : CERA/ Jaquar/ Prayag

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out complete all as specified and directed.

Supply & Fixed for 100mm bore sand cast iron pipe in any length including jointing with cement, in walls complete all as specified.

Supply & Fixed for 75mm bore sand cast iron pipe in any length including jointing with cement, in floor/trench complete all as specified.

Supply & Fixed cast iron bend 100mm bore complete all as specified.

Supply & Fixed cast iron bend 75mm bore complete all as specified.

Supply & Fixed branch pieces cast iron single (equal or unequal) 100mm bore complete all as specified.

Supply & Fixed branch pieces cast iron single (equal or unequal) 75mm bore complete all as specified.

Material and labour in repairs 75mm dia cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type-B-1 (1:2:4) using 12.5mm brick aggregate all as specified and directed.

Material and labour in repairs PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement including jointing to waste pipe fixed in cement concrete type-B-1 (1:2:4) using 12.5mm brick aggregate all as specified and directed.

Taking down old unserviceable copper/aluminium point wiring (light, fan, socket or power) complete including fittings and fixtures such as switches, ceiling rose, pendants, regulators, sockets, light fitting etc. and making good disturbed surfaces of walls, floors, etc. all as directed by engineer in charge.

Material & Labour for point wiring with 1.5 Sqmm multistranded,1100 volt grade copper conductor cable of PVC insulated, FRLS and unsheathed type alongwith 1.5 Sqmm PVC insulated stranded copper conductor cable for continous earthing in & including PVC rigid conduit concealed on stone/brick masonrty wall surface with accessories having ISI mark fixed on wall surfaces / ceiling including provision of PVC box of appropriate size for fixing switches sockets etc. all as specified for One light point / Fan/ bell point controlled by one switch.

One light point controlled by one switch with cables 1.5 sqmm size.

One fan/ exhaust fan point controlled by one switch with cables 1.5 sqmm size.

One 3 pin socket outlet, 5 amps on the same board with other switches, with cables 1.5 sqmm size.

One 3 Pin socket oulet 5Amps on indepndent, with cables 1.5 Sqmm size

One light point controlled by two 2 - way switches, with cables 1.5 sq.mm size.

One 3 Pin 15A pin socket oulet 15Amps on indepndent board with cables 2.5 Sqmm size.

One bell/ buzzer point controlled by one push button on the same board with other switches or independent with cables1.5 sq.mm size.

Supply & Fixing switch piano flush type single pole one way 5/6 Amps.

Supply & Fixing lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings including dismantling old one.

Supply & Fixing socket outlet 5 pin 5/6 Amps flush type multipurpose suitable for 3 pin/2 pin plug complete including dismantling old one.

Supply & Fixing of switch piano 15 Amp 230 Volt, flush button single pole one way complete all as specified and directed by Engr-in-Charge including dismantling old one.

Supply & Fixing socket outlet 2 in 1, 3 pin 5/6 Amps and 3 pin 15/16 Amps flush type including dismantling old one.

Supply & Fixing ceiling rose surface tpe 3 terminals to be fixed on PVC block including dismantling old one.

Supply & Fixing stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd.

Supply & Fixing switch piano flush type single pole two way 6 Amps.

Supply & Fixing Buzzer, Ding Dong AC. 230 volts, single pole

Supply & Fixing Bell push, flush type, 5 amp

Supply & Fixing LED integrated batten tube light fittings 20W 4 Feet long complete up with twin core twisted flexible copper conductor cable of size 23/0.0076 complete all as specfied and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply & Fixing LED lamp 9W system lumen (NOM) 600 with all accessories all as specified and directed by Engr-in-Charge.

Material & Labour MCB TPN DB comprising of sheet metal enclosure double door suitable for mounting MCB 415 Volts 4 way including dismantling old one.

Material & Labour MCB SPN DB comprising of sheet metal enclosure double door suitable for mounting MCB 240 Volts with busbar 200 amps rated 8 way including dismantling old one.

Supply & Fixing MCB TPN 63 Amps 415V 10KA 'B' curve miniature circuit breaker (MCB) and current carrying capacity in the DB complete with connection testing and commissioning.

Supply & Fixing RCBOs Double pole, 30mA 32 Amp rating for earth leakage, overload & short-circuit protection.

Supply and fixing SPN 32 Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning.

Supply and fixing SP 6 to 32 Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning.

Taking down carefully, deposited to MES store and hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan

Taking down old unsv exhaust fan, deposited to MES store and Supply & Fixing exhaust fans AC single phase 240 Volts of size 150/200mm sweep with louver and complete accessories including making hole with suitable size for Exhaust fan, after completer of work, finishing with cement and plastering and repainting with existing color all as specified and directed by Engr-in-Charge.

Material & labour for earthing complete with galvanised steel earth plate electrode 60x60cmx6.0 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below the ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level, connected to galvanised earth wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or of steel all as shown in electrical plate No 3 of SSR part-I 2009 connected to main switch board all as specified and testing on completion including. Necessary excavation, earthwork, PCC works and CI earth pit cover with watering pipe 20mm dia GI pipe medium grade, funnel with wire mesh and lugs and GI pipe 15 mm dia of light grade, for protection of earth lead complete all as specified and directed.

Supply & Fixing Submain wiring alongwith earth wire with the following sizes of 2x2.5 sqmm + 1x2.5sqmm earth wire FR PVC insulated copper conductor, single core cable in surface/recessed as required.

Supply & Fixing Submain wiring alongwith earth wire with the following sizes of 4x4.0 sqmm + 1x4.0 sqmm earth wire FR PVC insulated copper conductor, single core cable in surface/recessed as required.

Supply & Fixing LED security light luminaries of 20 watt for energy saving having IP-65 degree of protection made of pressure die cast aluminum housing and heat resistant thoughned glass with excellent thermal management, LED's should have better optics and uniform distribution of light including GI tubing 40mm dia light grade 1.2 mtr long pipe bent to shape 120 degree for mounting of security light and fixed to wall/pole, with suitable MS clamps 2 Nos with nut and bolt and washers including connecting complete including 2.5 sqmm stranded copper conductor of suitable length as per direction and approved by Engr-in-charge,

Taking down carefully, depostied to MES store and fix at the smae place electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25/50 litre as existing complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.

naveen enterprises

M/s Ajay kumar Garge

m/s sharma constructions