Special repair to building No MH-1A (Cook House) of 122 Inf Bn TA (MADRAS) at Mily Station Calicut under AGE (I) Cannanore.

Amount

Dismantling of asbestos cement (corrugated, semi corrugated, etc) sheets in roof covering including ridges all as directed.

Dismantling timber scantling 40 sqcm and over in section in any position unframed work all as specified and directed.

Dismantling tmber scantling in any position as in rails, posts, rafters, purlins etc under 40 sqcm in section complete all as specified and directed.

M&L for second class hard wood in scantlings clean sawn, unframed work, as in rafters, purlins etc. timber fixed all as specified and directed.

M&L for structural work in tubular trusses including special shaped washer, etc, complete using ERW or induction butt welded tubes etc Fe 410W (Gde E-250) quality B all as specified and directed.

M&L for preparing surfaces of wood and wood based materials new of any description and girth not otherwise described and treated with two coats of creosote oil all as specified and directed

Providing, cement concrete (1:2:4) type B0 (using 12.5mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

S&F Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridge/valley gutter/roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

M&L for preparation of new untreated steel surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed.

Demolition of brick or stone / boulder masonry built in cement or cement lime mortar, including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work and pre cast concrete articles and removing debris outside MD land all as directed.

M&L for providing pre-cast cement concrete block masonry with solid blocks, exc.10cm in width with PCC (1:3:6), type C1, using 20mm graded stone aggregate and set in cement mortar (1:6) complete all as specified and directed.

Taking down cement or cement lime plaster on brick/stone walls or in ceiling surfaces incl racking out joints hacking for key scrubbing down with water etc and removing rubbish outside MD land all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:6) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for rendering 15mm thick in cement mortar (1:4) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and removing debris outside MD land all as directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding(but not backing),removing serviceable tiles and rubbish off the premises all as directed.

M&L 25mm thick PCC 1:2:4, Type B1 (using 20mm graded stone aggregate) as in flooring and finished fair and even all as specified and directed.

M&L for light shade joint free non-skid ceramic tiles, 7mm to 8mm thick, area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:4) all as specified and directed.

M&L for coloured glazed ceramic tiles 450x350x7mm thick, as in skirting / dado, set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 10 mm thick backing on stone/brick masonry surfaces in cement mortar (1:4) all as specified and directed.

Dismantling wall and ceiling boards or insulation boards/slabs/blankets any thickness, including cover fillets all as directed.

S & F for anodized aluminium snap grid frame work as in clause No. 10.38 of MES Schedule Part I for false ceiling of size 605 mm x 605mm with supporting hanger comprising of 6 mm GI rod / GI flat 40x3mm, adjusting level with cleats, necessary washers, bolts and nuts for securing frame work to ceiling and to the snap grid complete all as specified and directed

S&F 4 mm thick non asbestos fiber cement building boards inserted to aluminium grid as per manufacturers instructions as in ceilings flat or sloping complete all as specified and directed.

M&L for preparation of new non AC ceiling board or gypsum board ceiling surfaces and applying three coats of white wash all as specified and directed.

Taking down chowkats with shutters any description n exc. 1.5 Sqm each (without taking off shutters from the frame) all as directed.

Taking down chowkats with shutters any description exc. 1.5 Sqm but n.exc 4 Sqm each (without taking off shutters from the frame) all as directed.

M&L for mild steel flat iron of size 25 x 3mm for holdfasts for securing new wooden frames and similar articles conforming to Fe-290 Gde-E-165 all as specified and directed.

M&L for PCC 1:2:4, type B1 using 20mm graded stone aggregate for fixing hold fast, coping, bed block etc including necessary form works all as specified and directed.

M&L for second class hardwood, plain, solid straight chowkats & frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints all as specified and directed.

All as per item No 29 here in before but for with transoms and mullions, with double rebated on the solid frame for fixing double shutters all as specified and directed.

M&L for second class hardwood, panelled shutter 35mm thick (two panel) with lock rail and panel of 9mm BWP, 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed.

S&F 30mm thick second class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc; (devide into square sash bar), edges of framing, fitted with cut and mitered beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, Section 8, Clause 8.24 (a) all as specified and directed.

S&F 4mm thick plane sheet glass, ordinary quality and glazing with oil putty in squares not exc 0.50 Sqm in each pane with putty or fixed with beads all as specified and directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treating back of chowkats,area tarred exc. 0.1 sqm but n.exc 0.5 sqm with tar or coal tar black paint each all as specified and directed.

S&F 200mm long aluminum anodized barrel tower bolts of extruded section fixed with stainless steel screws all as specified.

S&F 75mm long aluminum anodized barrel tower bolts of extruded section fixed with stainless steel screws all as specified.

S&F Harrison rails 25mm dia, chromium plated with fixing brackets , stops, rollers etc. all as specified and as directed.

S&F stainless steel butt hinges medium weight; 100mm size as per IS 21817 fixed with stainless steel screws all as specified.

S&F stainless steel butt hinges medium weight; 75mm size as per IS 21817 fixed with stainless steel screws all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 150mm size fixed with stainless steel screws all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 75mm size fixed with stainless steel screws all as specified.

S&F mild steel or cast iron (malleable) casement stays 250mm long with hinged joints and two plates with studs complete all as specified and directed.

S&F aluminium anodised sliding door bolts 300mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed

S&F Floor door stopper Overall length of cover plate 140mm of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor etc complete all as directed.

M&L preparing new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer all as specified and directed.

M&L preparing old treated wooden surfaces of any description over 10 cm width or girth and applying a coat of synthetic enamel painting all as specified and directed.

M&L for complete removal of existing treatment on surfaces of wall by scrapping down and applying 1mm thick acrylic wall care putty and making the surface smooth and even and applying two coats of oil emulsion distemper over a coat of wall primer (water or solvent thinnable) and all as specified and as directed.

M & L for preparation of newly plastered surfaces of wall and applying 1mm thick acrylic wall care putty and making the surface smooth and even including sanding each layer to receive next new layer, one coat of wall primer and applying two coats of oil emulsion distemper and all as specified and as directed.

M&L for complete removal of existing treatment on surfaces of wall by scrapping down, preparation of surfaces and applying two coats of cement base paint over a coat of primer all as specified and as directed.

M&L preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer all as specified and as directed.

M&L solid PVC door frame of sizes 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, all as specified and directed.

S&F factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain coloured PVC “C” channel having a PVC sheet strip of 20mm width stock inside with solvent cement for stiles and plain colour PVC sheet for top rails, lock rails and bottom rails on either side and as gap insert for top rail & bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour of PVC sheet fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement etc. Details as peer specification and drawings and all as directed.

S&F 500 litres capacity rotational moulded polthylene water storage tanks(cylindrical vertical with closed top) of make Sintex/Polycon/Plasto hoisted and fixed in position including taking down unserviceable water tank all as specified in SSR Part I,2009 and directed.

S&F ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule of 25 mm bore dia all as specified and directed.

Taking up or down steel tubing and connecting including cleaning for removing to store of sizes upto 20mm bore all as directed.

S&F for 15mm bore UPVC pipes of pressure rating 10 kgf / cm2, fixed complete to walls, ceilings or in floors etc. all as specified and directed.

S&F for 20mm bore UPVC pipes of pressure rating 10 kgf / cm2, fixed to wall/ceiling or on floor all as specified and directed.

Dismantling and breaking up drain pipes 75/100mm bore (cast iron) set in cement mortar any dia of pipes and removing debris outside MD land all as directed.

M&L PVC (SWR) pipe type 'B' 75mm bore single socketed with solvent cement joints laid in trenches or in floors all as specified and directed.

M&L PVC (SWR) pipe type 'B' 110mm bore single socketed with solvent cement joints laid in trenches or in floors all as specified and directed.

S&F 75 mm bore, PVC (SWR) bends with access door all as specified and directed

S&F 110 mm bore, PVC (SWR) bends with access door all as specified and directed

S&F 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal all as specified and directed

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement all as specified and directed.

M&L for 75mm diameter PVC (SWR) floor trap, plain with grating including jointing with solvent cement all as specified and directed.

S&F grating square 150mm size of PTMT complete all as specified and as directed.

Cutting chases on wall of width 30mm and depth 35mm for concealing water tubing 15/20mm dia and making good the surface with plastering in cement mortar 1:4 and finish to match the existing surface and treated with existing treatment such as white wash/OBD/cement base paint etc complete all as directed.

S&F Vitreous China premium/1st quality Wash down water closet pan, white or ivory (excluding flushing cistern and flush type) pedestal pan and trap including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe, etc complete including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device as fixed in repairs all as specified and directed.

S&F in repairs Vitreous China valveless, syphonic action type flushing cistern low level, 10 Litre capacity, white, with inlet, ball valve, float and handle including low or high density suitable size PVC flush pipe all as specified and directed.

S&F mild steel chromium plated Health faucet (ABS body), suitable for 15mm dia pipe with flexible LDPE pipe with jet of 1.25m long on one end and socket joint of 15 mm dia on other end including ABS wall hook complete all as specified and directed.

S&F in repair Vitreous China Wash basin, white, flat back, size 630 x 450 mm, including CI brackets, (but excl. pillar tap) cutting for and pinning in ends of brackets or erecting stand etc complete all as specified and directed.

S&F 15mm pillar taps, cast copper alloy with capstan heads, chromium plated , screwed down high pressure ,with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed all as specified and directed.

S&F 32mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed all as specified and directed.

Supply and fix PVC connecton 60cm long with PTMT nuts for flush tank, wash basin, etc. all as specified and directed

S&F in repairs bib tap 15mm dia, chromium plated, fancy type, cast copper alloy, screwed down, screwed for iron pipe or ferrule and complete all as directed.

S&F in repairs stop cock 15mm bore cast copper alloy, chromium plated, screwed both ends for iron pipe or for unions and screwed down, high pressure with long shank & cup complete all as specified and directed

S&F in repairs stop cock 15mm bore cast copper alloy, chromium plated, screwed both ends for iron pipe or for unions and screwed down, high pressure with long shank & cup complete all as specified and directed

S & F in repairs brass chromium plated shower rose 125 mm dia suitable to 15mm bore pipe complete all as specified and as directed.

M & L PTMT Shower arm 15 mm size , 195 mm long with bend of 45 degree with flange, any colour (mininmum weight 40gms) complete all as specified and as directed.

S&F tubular towel rail brass, chromium plated, D type, 60cm long between flanges fixed to wall with wooden plugs with chromium plated brass screws all as specified and directed.

S&F in repairs Stainless steel sinks 1mm thick with plugs, washers and waste; including bedding in cement mortar on to dwarf walls, or including fixing cantilever brackets and connecting union to waste pipe, overall size 495mm x 420mm, bowl size 410 x 330 x 160mm etc complete all as specified and directed.

Taking down carefully copper/aluminium point wiring of light, fan, socket or power socket complete, including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and making good disturbed surfaces of walls, floor ceiling etc. all as directed

M&L Point wiring complete with 1.5 Sq mm single core PVC insulated unsheathed copper conductor FRLS cable multi stranded 1100 Volt grade drawn through and including non metallic rigid PVC conduit, medium grade concealed and fixed to ceiling/roof etc with necessary fixing accessories such as bend elbow socket etc with fixing material including terminal box made out of 1.22mm thick GI sheet concealed in wall covered with bakalite/plastic laminated sheet top cover of 3mm thick cadmium plated screws with cup washer including 1.5Sqmm single core PVC insulated un sheathed copper conductor FRLS cable multi stranded 1100Volt grade as earth continuity conductor green in colour connected to common earth dolly complete all as specified and as directed for One light/fan/bell point controlled by one switch.

All as per item No 84 here in before but for One 3 Pin, 5 Amps socket on same board with other switches all as specified and directed.

All as per item No 84 here in before but for One 3 Pin, 5 Amps switch socket combination on independent board all as specified and directed.

All as per item No. 84 on here in before but for one 3 pin 15 amp switch socket combination on independent board with 2.5Sqmm unsheathed PVC insulated copper conductor FRLS cable including 2.5 Sqmm PVC insulated copper cable for earth continuity conductor complete all as specified. Note for item No 84 to 87 : Wiring shall be done with proper colour coding as per IE standard.

S & F switch piano flush type, single pole, one way, 5 Amps, 240 volt including connecting up electrically complete all as specified and as directed.

S & F PVC ceiling rose 65x50mm size, three terminals, polycarbonate, isolated body including connecting up electrically all as specified and as directed.

S & F socket 5pin 5/6 Amps, multipurpose, flush type, non-interlocking type, including connecting up electrically complete all as specified and directed.

S & F socket 5pin 5/15 Amps, multipurpose, flush type, non-interlocking type, including connecting up electrically complete all as specified and directed.

S & F switch piano flush type, single pole, one way, 15 Amps, SP,240 volt including connecting up electrically complete all as specified and as directed.

S&F stepped type electronic fan regulator, full rotation, 200W, SP, 230V connecting up electricallyall as specified and directed.

S&F lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings and electrically connecting up including self ballasted LED bulb 15 watt with PBT body shell and PC diffuser, 240 degree wide distribution available CCT 3000K and 6500K complete all as directed.

Taking down unserviceable fluorescent tube light fittings, S & F Decorative ultra slim square profile linear LED light fittings with extruded polycarbonate, heat sink, environmental friendly, energy efficient ready to use pack of 4 feet 20 W LED 6000K, model LHEXBLP7PN1W020 of Havells or equivalent in Syska or Crompton Greaves with all accessoried internally prewired and including connecting up with twin core twisted copper flexible conductor cable of sutibale size all as directed.

M&L for sub main wiring with two runs of single core 6 Sq mm copper conductor FRLS cable, PVC insulated, unsheathed multistanded, 1100 V grade, ISI marked drawn through and including non metallic rigid PVC conduit 25mm dia with all accessories such as bend,elbow,socket,tee saddles etc fixed concealed to wall / fixed to ceiling etc including 6 Sq mm single core copper conductor FRLS cable PVC insulated, unsheathed multistranded 1100 V grade as earth continuity conductor connected to common earth dolly including cutting chases and making good the surface with in cement mortar and finished the surfaces to the existing, complete all as specified and directed. Note :- 3 runs of 6 Sq mm copper cable and one run of PVC conduit will be measured as one length.

S & F MCB SP, 240 Volt, 6 to 32Amps, 10KA, B series, 50Hz, including electrically connecting up using wiring lugs all as specified and directed.

S & F MCB SPN, 240 Volt, 63Amps, 10KA, C series, 50Hz, including electrically connecting up using wiring lugs all as specified and directed.

S & F sheet metal enclosure factory made for MCB DB, SPN 6 way with 200 Amps bus bar, 240 Volt, double door type, fixed/flushed on wall including electrically connecting up and taking down old unserviceable DB complete all as specified and directed.

Supply and fix in replacement GI bracket for street light fitting made out of 50 mm dia, light grade 1.5 mtr long each bent to required shape & size and fixed to pole with suitable flat iron clamps made out of 25X4mm, 02 Nos including GI nuts, bolts & washer including painting with one coat of red oxide primer, one under coat and one finishing coat with alumminium paint to clamps and GI bracket complete all as specified and directed.

Supply and fix 25 W LED Street Light luminaire made up of pressure Die Cast aluminum housing with black epoxy polyester powder coating for long life, IP66 for Optical Compartment covered with heat resistant toughened glass for safety and Control Gear Compartment, multiple LEDs to get sufficient light output, Integral type, 150V to 270V. Driver shall be of isolated type with Constant Current Constant Voltage topology to ensure optimum driving of LEDs. Light shall have power factor more than 0.95 of Make : Havells of cat No LHEXAYP7PN6K030 or equivalent of Crompton/ Bajaj and electrically connecting up including taking down old unserviceable light all as directed

S&F in repalacement LED ball type lamp 15watt all as directed.

M & L for earthing complete with galvanized steel earth plate electrode 60cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron connected to earthing test point, main DB, panel board, continuous earth lead protected by 15mm bore GI pipe light grade, 20mm bore GI light grade pipe for watering, necessary excavation and earth work in any type of soil, PCC pit, RCC chamber cover with suitable reinforcement complete all as shown on electrical plate No 3 of SSR part-I of 2009 all as specified and directed. Note :- Rate quoted shall deem to include for GI earth and GI pipe lead upto 7.5m length.

ZOOM ENTERPRISES