GE 874/EWS-39/2022-23

Amount

B/R and E/M Portion

Surface excavation n.exceeding 30 cm deep and averaging 15 cm deep and getting out in any type of soil.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil.

All as per item above but additional 1.5m or part thereof in depth beyond the first 1.5 m and getting out in soft/loose soil.

M&L Plain Cement Conrete (1:4:8) type D2 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete.

RCC design mix M-25 (20 mm graded aggregate use in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for flat rough finished concrete.

RCC design mix M-25 (using 20 mm graded aggregate ) as in beams, cantilivers, bressummers, linteils over 1.5 m span.

Formwork to sides and soffits of floor or roof beam, beam hauchings girders, bressummers, lintels etc. for rough finished surfaces of concrete.

RCC design mix M-25 (20 mm graded aggregate) as in Columns, pillars, piers, posts and struts.

Precast cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in chullah hoods, stairways (except spiral staircase) including steps (square or spandril), string pieces, carriang, etc complete any section straight or winding, but excluding landings complete all as specified and directed by Engineer-in-Charge.

20 to 18mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like over15 mm thick screed bed in cement mortar (1:4) bed including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified & directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions, Square, rectangular on plan or polygon for rough finished surfaces of concrete.

M&L TMT bars 10mm dia and over, cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as spd & directed.

M&L TMT bars 5mm dia and over upto including 10mm dia in stirrups spaces and binders cut to length bend to shape required including mild steel wire ( annealed) not less than 0.9 mm dia all as spd and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. loose/soft soil.

Removing excavated material n.exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point.

RCC design mix M-25 (using 20 mm graded aggregate use) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like (tank slab).

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping for rough finished surfaces of concrete.

M&L brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in Cement Mortar 1:6.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius built in Cement Mortar 1:4 all in half brick thick as specified and directed.

M&L for 10 mm thick rendering in CM 1:6 on fair faces of brick or concrete surfaces of walls & finishing the surface even and smooth complete all as specified and directed.

M & L for rendering 15mm thick on stone masonry surfaces or other than fair faces of brick work or on one side of lathing in Cement Mortar 1:4 finished even and smooth without using extra cement, including water proofing compound. (Water proofing compound shall be measured and paid separetely)

Supply only integral water proofing compound.

M & L for rendering 5 mm thick in CM 1:3 on ceiling surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for 12 mm thick rendering in CM 1:4 on other than fair faces of brick or concrete surfaces of walls & finishing the surface even and smooth complete all as specified and directed.

M&L for applying three coats of white wash on wall including preparation of plastered or un-plastered surfaces of walls, complete all as specified and directed.

M&L for applying three coats of white wash on ceiling including preparation of new plastered or un-plastered surfaces, complete all as specified and directed.

M&L for applying two coats of cement base paint on wall over a coat of priming paint including preparation of new plastered or un-plastered surfaces, complete all as specified and directed.

Rolled Mild steel works as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc confirming to Fe410-W (Grade E-250) quality A complete all as specified and directed.

S&F for Bands, straps supports or stay for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy for large gates, hook and pintle hinges, large hasps and staples, chains, handmade sliding bolts, clamps, hold fasts, wall tiles, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L for eves board 1.40 mm thick with angle iron/flat iron space between wall iron framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165.

M& L for E-board ceiling 6mm thick precoated non asbestous E board classic designer tiles of size 595x605mm manufactured by Everest Eternite Ltd. Fixed in GI snap grid interlocking system powder coated at bottom of same manufactures including GI wire as per manufacturer specifications. if pre coating is spoiled by worker while fixing of tiles the complete tile surface shall be provided with 2 coats of plastic emulsion paint without any price adjustment complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screwscomplete all as specified.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screwscomplete all as specified.

M&L moorum /red bajri filling at side of road berm or pavings, laid in layers n.exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L 40mm thick Damp proof course in Plain Cement Mortar 1:2:4 type B-0 to horizontal or vertical surfaces including necessary formwork using WPC as per manufacturer's instructions complete all as specified and directed.(WPC shall be measured and paid separately).

M&L for 75 mm thick Cement Conrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in sub base of floors.

M&L for non skid ceramic coloured tiles 7mm to 8 mm thick (square /rectangular), area of each tiles exceeding 0.06 but n exc 0.11 Sqm in floors etc, laid over including 15 mm thick screed bed or bedding layer in cement mortar 1:6 over 25 mm thick PCC 1:2:4 type B-0 (12.5 mm graded aggregate) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, complete all as specified and directed

M & L for glazed ceramic tiles of size 300 x 200 x 7 mm/450x350x7 mm coloured in vertical surfaces such as riser of steps, skirting, dado and pillar, over and including 10mm thick rendering as bed or bedding layer in cement mortar 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for 20-25 mm thick kota stone as in floors etc, laid over including 15 mm thick screed bed or bedding layer in cement mortar 1:6 over 25 mm thick PCC 1:2:4 type B-0 (12.5 mm graded aggregate) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete all as specified and directed

M&L for 18-20 mm thick kota stone as in vertical surfaces such as riser of steps, skirting, dado and pillar, over and including 10mm thick rendering as bed or bedding layer in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L hardcore of gauge n exc. 63 mm,broken stone Broken or boulders deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M&L for 75mm thick PCC 1:3:6 C-1 using 20mm graded crushed stone aggregate over hard core (of broken stone aggregate) 75mm thick over compacted formation as in plinth protection finished even and fair. Plinth protection is to be casted in panels not exc. 2 Sqm each in an outward slope of 1 :10 with 6mm joints filled with bitumen mastic filling complete all as specified and as directed.

S&F for 1.2 mm thick Pressed steel frames size 125 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed

S&F 35 mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneeringon both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S & F Steel windows with side hung shutters including projecting type hinge with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S & F steel ventilators with top hung shutters including hinges, steel peg stay complete all as specified and directed.

S & F Mild steel work in framed work such as grills, gratings, guard bars etc, with ends of bars shouldered and/ or riveted, or forged into spikes, and similar work confirming to Fe 410 - O or Fe 310 - O complete all as specified & directed.

S & F Galvanized mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned stacks, or galvanized wire staples complete all as specified and directed

S&F 4 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq. M in each pane complete all as specified and directed.

S&F frosted or grouded/obscured type sheet glass, 4mm thick and glazing with oil putty in squares n.exc. 0.5 Sqm in each pane complete all as specified and as directed.

S&F Factory made solid panel PVC moulded door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F solid PVC door frame of size 50x47mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube supplying & fixing in opening as specified in clause No. 8B.3 at Sl page No. 145 and shown in drawing on sl page No 160 of SSR 2010 respectively and as directed.

Second class soft wood plain, solid straight chowkats and frames, wrought framed rebated on the solid rounded or chamfered, put together with glue pinned and joints.

S&F 16 mm outer dia 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. in any length complete all as specified.

S&F 20 mm outer dia 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. in any length complete all as specified.

Lagging to pipes 20mm bore used in internal water supply or plumbing all round with 25mm thick bonded mineral wool preformed 'SNAP ON' pipe sections of density 144Kg/Cum conforming to IS-9842 provided with chicken mesh wire netting 25 gauge, 20mm mesh and covered with 0.01mm aluminium foil complete all as specified and directed.

S&F 20mm bore gun metal globe or gate valve with iron wheel head, screwed both ends.

S&F 25mm bore gun metal globe or gate valve with iron wheel head, screwed both ends.

S&F 15mm bore Bib taps chromium plated fancy type cast copper alloy with crutch or butter-fly handle screwed down, screwed for iron pipe or for brass ferrules, complete all as specified and directed.

S&F Swivel shower of PTMT any colour for fixing with 15mm pipe.(Minimum weight 40gms) with arm 195mm long with bend of 45 degree with flange of PTMT of any colour complete all as specified and directed.

Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms) complete all as specified.

S&F for aluuminium Alloy Sliding door bolt, with hasp and staple, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy and fixed with bright bolt not less than 12mm dia of 200mm long.

S&F 250 mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixedcomplete all as specified and directed.

S&F 100 mm long medium weight, cold rolled mild steel Butt hinges complete all as specified and directed.

Mild steel pressed handle, oval type stove enamelled, black of size 150mm, complete all as specified.

Mild steel pressed handle, oval type stove enamelled, black of size 100mm, complete all as specified.

S&F 150mm long MS handles, complete all as specified and directed.

S&F 300mm, MS ordinary rat tail rod pattern springs including roller and roller plate complete , complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint (Ordinary tint) over a coat of pink primer including preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth complete all as specified and directed.

M & L for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10 cm width or girth, not otherwise described complete all as specified and directed.

S&F 150 mm long MS tower bolts of complete all as specified and directed.

S&F 100 mm long MS tower bolts of complete all as specified and directed.

M&L for Vitreous china squatting Pan "Orrisa Pattern" size 580 x 440mm white with integral foot rests incl flush pipe of PVC 32mm dia for low level cistern fixed including connection to trap complete all as specified.

Wash hand basin, vitreous china white of size 550x 400mm excluding taps, waste chain and plug and porcelain stopper but including brackets,32mm waste fitting and waste pipe of 32 mm bore, brass, chromium plated for glazed ware wash basin and 15mm dia pillar taps chromium plated fancy type etc complete all as specified and directed.

Vitreous china bowl urinal flat back, size of 465x355x265mm white (minimum), with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws and pointing around urinal back in cement etc and 32mm dia PVC waste pipe, complete all as specified.

S&F 500 ltrs capacity rotational moulded polyethylene water storage tank double layered, ISI engraved (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed.

S&F 1000 ltrs capacity rotational moulded polyethylene water storage tank double layered, ISI engraved (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed.

S&F 75 mm dia of PVC (SWR) pipes single socketed in any length wih rubber rings joints laid in trenches complete all as specified and directed

S&F 110 mm dia of PVC (SWR) pipes single socketed in any length wih rubber rings joints laid in trenches complete all as specified and directed

S&F PVC grating 100mm dia fixed to floor trap.

S&F PVC gully trap square or round mouthed type (P) , size of trap 125x 110mm and jointing to drains with solvent cement complete all as specified.

S&F 110mm bore PVC (SWR) bend or tee or radius complete all as specified.

S&F 75mm bore PVC (SWR) bend or tee or radius complete all as specified.

S&F 75 mm dia of PVC (SWR) floor trap with grating with solvent cement laid in trenches complete all as specified and directed.

S&F 110 mm dia of PVC (SWR) WC connector with lip ring 110 mm complete all as specified and directed

M&L for PVC (SWR) vent cowl for 75 mm dia all as specified.

M&L for PVC (SWR) Reducer 110/75mm dia all as specified.

S&F S&F 20mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 20 mm dia (minimum weight - 210 gm) complete

S&F PVC valve-less symphonic action type flushing cistern, low level white with inlet ball valve float and handle incl brackets (10 Ltr) capacity complete all as specified and directed.

Soap dish, vitreous China white, approximate size 160x 160x90mm

S&F PVC connection 15mm dia and 600mm long with PTMT nuts and washer complete all as specified.

Stop valve 15mm bore, fancy type chromium plated, with long shank, concealed type cast copper alloy screwed down, high pressure, with crutch jor butter fly handle, screwed both ends for iron pipe or for unions complete all as specified and directed

Stop valve 15mm bore, cast copper alloy screwed down, high pressure, with crutch jor butter fly handle, screwed both ends for iron pipe or for unions complete all as specified and directed

S & F CP Pillar taps, with capstan head chromium plated 15 mm bore fancy type complete all as specified and directed

S & F Waste coupling of PTMT (half or full thread ). (Minimum weight 32 mm-45 gms / 40mm-60gms) for 32mm bore dia of discharge pipe fixed to WHB , sink complete all as specified and directed.

Construction of brick work of stone masonary stagging for over head water tank 2.40 mtr heigh from ground level including necessary earth work in any type of soil, PCC foundation, pointing, RCC bracing and slab all as showen in drawing No. CESZ/TD-1101/2011 sheet 1/1 dt 01/12/2011 complete all as specified and directed.

Construction of 10 users septic tank (brick construction) including inlet and out let chamber with top of slab at ground level including necessary earth work and disposal of surplus soil to a distance not exceeding 50m supplying and placing vent pipe, in position to manhole cover brick construction and all other relevant works, complete, all as specified and shown on drawing No CESZ/TD-01/2015 Sheet 1/1&1/2 dated 22 Feb 2015 and revised on 06/06/15.

Construction of Soakage well, excavation in any type of soil, foundation in PCC 1:3:6, Wells of honey combed and solid brick work in CM, RCC cover slab in , filling with brick bats complete of size 1.80 m inner dia x 3.0m deep all as specified and shown on drawing No CESZ/TD-01/2015 Sheet 3/3 dated 22 Feb 2015 and revised on 06/06/15.

Construction of 25 users septic tank (brick construction) including inlet and out let chamber with top of slab at ground level including necessary earth work and disposal of surplus soil to a distance not exceeding 50m supplying and placing vent pipe, in position to manhole cover brick construction and all other relevant works, complete, all as specified and shown on drawing No CESZ/TD-01/2015 Sheet 1/3 & 2/3 dated 22 Feb 2015 and revised on 06/06/15.

Plain cement concrete bed 1:3:6 type C-2 using 40mm graded stone aggregate to drain pipes of 150mm bore including packing under hunching against the site of pipe after they are laid and tested.

S&F PVC drain pipes of 150mm bore laid in trenches and jointed on concrete bed complete all as specified and directed.

PCC (1:2:4) type B-1 (using 20mm graded stone aggregate), in coping and the like including weathering, slightly rounded/ chamfered angles with and including necessary use and waste of form work for fair finished surfaces of concrete, complete all as specified and directed.

Precast Cement cocnrete 1:2:4 type B1 (using 20mm graded crushed stone aggregate) as in landing /cover slab of septic tank/ soakage well / manhole cover and set in cement mortar 1:4 complete all as specified.

M&L for 100 mm thick Cement Conrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in sub base of floors.

M&L 60mm thick, machine pressed precast concrete interlocking paver block, with grey cement and pigment, any shape and size over sand cushion 25mm thick filling under floors/ path including watering and consolidation confirming to IS 15658-2006, M-35 Grade complete all as specified and directed.

Providing Precast cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in kerb stone and the like and set in Cement mortar 1:4 complte all as specified and directed.

Point wiring for one light point/Ex/fan point controlled by one switch with 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi strand cable and 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi stranded cable (green color) as earth lead in and including cable 1100 volts grade including 25mm casing and capping (ISI marked) for one light/ fan point controlled by one switch including CI/MS sunk box of required size, & as directed by Engr in Charge including 3mm thick plastic laminated top sheet cover, including cutting chases to wall and making good the disturbed surfaces to match with the existing specification complete all as specified.Make : Finolex/Anchor/Polycab

Point wiring for 3 pin 5A socket outlet independent point controlled by one switch with 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi strand cable and 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi stranded cable (green color) as earth lead, 1100 volts grade including 25mm casing and capping (ISI marked) for one light/ fan point controlled by one switch including CI/MS sunk box of required size, & as directed by Engr in Charge including 3mm thick plastic laminated top sheet cover, including cutting chases to wall and making good the disturbed surfaces to match with the existing specification complete all as specified.Make : Finolex/Anchor/Polycab

Point wiring for 3 pin 5A socket outlet on the same board controlled by one switch with 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi strand cable and 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi stranded cable (green color) as earth lead, 1100 volts grade including 25mm casing and capping (ISI marked) for one light/ fan point controlled by one switch including CI/MS sunk box of required size, & as directed by Engr in Charge including 3mm thick plastic laminated top sheet cover, including cutting chases to wall and making good the disturbed surfaces to match with the existing specification complete all as specified.Make : Finolex/Anchor/Polycab

Point wiring for one 3 pin 15 Amps socket outlet/sheet metal enclosure independent with 4.00 sqmm PVC insulated un-sheathed copper conductor single core multi strand cable and 2.5 sqmm PVC insulated un-sheathed copper conductor single core cable (green color) as earth lead in and including 25mm PVC caping casing medium grade with all fittings (ISI Marked) controlled by one switch including CI/MS sunk box of required size, & as directed by Engr in Charge including 3mm thick plastic laminated top sheet cover, including cutting chases to wall and making good the disturbed surfaces to match with the existing specification complete all as specified.Make : Finolex/Anchor/Polycab

Point wiring for one 3 pin 15 Amps socket outlet/sheet metal enclosure independent with 2.50 sqmm PVC insulated un-sheathed copper conductor single core multi strand cable and 1.5 sqmm PVC insulated un-sheathed copper conductor single core cable (green color) as earth lead in and including 25mm PVC caping casing medium grade with all fittings (ISI Marked) controlled by one switch including CI/MS sunk box of required size, & as directed by Engr in Charge including 3mm thick plastic laminated top sheet cover, including cutting chases to wall and making good the disturbed surfaces to match with the existing specification complete all as specified.Make : Finolex/Anchor/Polycab

M&L for LED Batten 1x20 W for regal batten for LED Universal batten for G 13 T with 18 W tube rods and Ultra bright LED Polycarbonate tube light very high efficiency suited for installation in existing T8 and connecting electrically using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site or directed by Engineer-in-Charge.Make :Havells Batten Cat part No LHFYBYG21N1W020 and LED Tube Rod Cat part No LHLDCLXNUL8X018 or Equivalent.

Supply & fixing Switch piano type flush 6 Amp Single pole one way ( ISI Marked) complete all as specified and directed. Make : Havells/Anchor

Supply & fixing Switch socket combination 5 in 1, 5 and 15 Amp flush type universal controlled by one switch (ISI marked) complete all as specified and directed. Make : Havells/Anchor

Supply & fixing Switch modular type flush 6 Amp Single pole one way ( ISI Marked) complete all as specified and directed. Make : Havells/Anchor

Supply & fixing Switch socket combination 2 in 1, 5 and 6 Amp Modular type universal controlled by one switch (ISI marked) complete all as specified and directed. Make : Havells/Anchor/Philips

Supply & fixing Switch socket combination 5 in 1, 5 and 15 Amp Modular type universal controlled by one switch (ISI marked) complete all as specified and directed. Make : Havells/Anchor/Philips

Supply & Fixing Socket outlet 2 in1, 3 pin 6 Amps Modular type complete all as specified and directed.Make : Havells/Anchor/ Philips

S&F rectangular boards/ blocks 30x25x4cm depth closed recessed, complete all as specified and as directed by Engr-in -charge.

Supply & Fixing ceiling rose surface backelite 65x50mm two to three terminal (ISI marked).Make : Havells/Anchor

Supply and fixing lamp holder bracket type, PVC/polycarbonate type with skirt cap suitable for batten fittings, complete all as specified and direted.Make : Havells/Anchor

Supply and fix LED Bulb 9 Watt. Make Havells/Bajaj.

S&F LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and as directed.

Supply & fix sheet metal enclosure MCB distribution board. Single pole & neutral 240 volts 8 way with IP-43 IK-09 protection single door complete with appropriate size bus bar and neutral link, conf to Cat Pt No 6077 11 of Legrand or equivalent of make Hager/Merlin Garin fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification .

Supply & Fixing RCBO, single pole and neutral (SPN) 30mA, 240V , 32 Amp all as specified and directed. Make- Havelles/MDS/Legrand.

Supply & Fixing RCBO, single pole and neutral (SPN) 300mA, 240V , 6-63 Amp all as specified and directed. Make- Havelles/MDS/Legrand.

Supply and fixing MCB SPN 40 to 63 AMP amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning

Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning.

Supply laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cable (heavy duty) 1100 Volts graded standard aluminium conductor of size 35 sqmm 3.5 core complete all as specified and directed. Make Havells/Polycab/Gloster

Supply laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cable (heavy duty) 1100 Volts graded standard aluminium conductor of size 16 sqmm 2 core complete all as specified and directed. Make Havells/Polycab/Gloster

S&F 1100 volt grade heavy duty cable PVC insulated multistranded aluminum stranded conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 mtr apart including 4mm dia GI suspension wire one twin core cable flat of circular of size 16 Sqmm complete all as specified and as directed by Engr-in-Charge. Make : Havells/Anchor/Polycab/Plaza.

S & F in repair PTMT nipple 20 mm suitable for HDPE water tank, (Minimum weight 15mm 38gms/20mm-45gms /25mm- 65gms)

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6.3cm thick burried directly in ground ( earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanised iron wire 4.0mm dia by means of bolts, nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 connected to earthing test all as specified or indicated including testing on completion.

Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron earth lead strip 32x6mm by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI light grade water pipe 20mm dia with funnel all as shown in electric plate No. 3 of 2009 SSR Pt-I and testing complete including earth work in any type of soil, PCC 1:2:4 type B-0 as in earthing pit and cover 55mm thick reinforced with XPM (weight not less than 4.0Kg/Sqm) common salt, charcoal and testing on completion, all as specified and directed.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 20 mm bore GI tubing.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 25 mm bore GI tubing.

Storage water heater (Geyser), vertical type, of 25 ltr capacity of inner tank, outer tank, syphon assembly, thermostat heating element, safety valve etc complete all as per manufacturer design and specifications including making of all fixing arrangements complete having BEE Five Star Rating including grouting of nuts and bolts and necessary PCC work as specified and directed by Engineer-in-Charge. Make : Havells model Monza DX HSN code 8516 or equivalent as approved by Engr-in-charge.

Cutting of existing steel tubing for alteration or additions and insertion of Tee 40x40x25 mm /50x50x25 mm all as specified and as directed.

POPULARHARDWARESTORE

Bidder Name

POPULARHARDWARESTORE

M/S AK CONSTRUCTION