SPECIAL REPAIR REPLACEMENT OF VARIOUS PUMP MOTOR SET AND PROVISION OF BANK TYPE COUNTERS UNDER GE BRICHGUNJ PORT BLAIR.

Amount

Taking down/disconnection of electrical connection from Centrifugal Monoblock Pump Set / Submersible pump Set of any type /capacity (1 HP to 5 HP) from existing site depositing the same at E/M Store yard and complete all as specified and as directed.

Supply, installation, testing and commissioning of SS 304 Flash mixer motor with reduction gear box of capacity 1 HP, Agitator complete with Base Frame, Bearing Housing, 1.50 HP Geared Motor, SS 304 Impeller with 4 Nos Blade SS 304, Shaft SS 304 2000 mm long or as per site condition, Coupling, GM Guide Bush, supporting Channel, with suitable starter and suitable size three core sheathed copper cable from motor to starter complete all as specified and directed (No of Motor - 01 No) Rates inclusive of foundation for motor and gear box, nuts and bolts etc with all fittings, wiring, cable etc as per site requirement.

Supply, installation, testing and commissioning of MS Epoxy Painted Lime assembly for Semicircular Lime slaking tank 1500 mm dia x 2700 mm Long complete with SS 410 Shaft, Aluminium fabricated rotating cage with 6 Nos Angle arm Collecting Cup, supporting bearing, coupling, Cast Iron Spur Gear and Pinion, Stuffing Box, love Joy Coupling, Gear Motor 1.1 KW one No, Gear Head Helical type with SS 316 Bolt Nut and washer, Base Frame for Gear Head & Motor with suitable starter and suitable size three core copper cable from motor to starter complete all complete all as specified and as directed.Rates inclusive of foundation for motor and gear box, nuts and bolts etc with all fittings, wiring, cable etc as per site requirement.

Supply, installation, testing and commissioning of following Gear Motor and Panel of Clarifier & Flocculator Zone Scrapper with MS Hanger, MS. Blades, Rubber Squeezer, Central Bearing with CI housing and Carbon Steel Racer, Chrome Steel Ball, 5 Ring Current Collector, End Carriage Drive with Carbon Steel, Idle & Driving Wheel (200 mm dia x 125mm wide); M.S. Idle Shaft & Driving Shaft, CI Plummer Block with Bearing and Carbon Steel chain with CI sprocket, 2 sets Flocculator Paddle with M.S Epoxy Painted Paddle, C.I. Bearing Housing. 40 x 40 mm Carbon Steel Square Bar for wheel Track with fixtures Bolt, Nut. Scraper Blade will be of M.S IS 2062 with Neoprene Rubber Squeeze. All Gearbox and Motor with suitable starter and suitable size three core sheathed copper cable from motor to starter all as specified and as directed. Existing Clarifloculator Bridge of 19.0 mtr. dia RCC Tank Clarifier zone and complete with Fabricated Bridge with 1200 mm wide walkway with 6 mm thick MS checkered plate with minor repair and painting shall be used for installation of complete equipments :- (a) End Carriage Drive Gear motor Motor 2.0 HP - 01 Nos, Flocculator Gear Motor 1.0 HP – 2 Nos (b) Electrical Panel for operation of 3 Nos Motor of Clarifloculator. Rates inclusive of foundation for motor and gear box, nuts and bolts etc with all fittings, wiring, cable etc as per site requirement.

Supply installation testing and commissioning of Alum motor SS 304 Paddle type Agitator complete with Base Frame Bearing Housing, 1.0 HP Motor with Gear Box , SS 304 Impeller with 1 Sets SS 304 Paddle SS 304, Shaft 1500 mm long CI Coupling etc suitable for RCC Tank, Base Frame 900 mm long with suitable starter and suitable size three core sheathed copper cable from motor to starter complete all as specified and as directed. Rates inclusive of foundation for motor and gear box, nuts and bolts etc with all fittings, wiring, cable etc as per site requirement.

Supply installation testing and commissioning of SS Monoblock Pump Set with SS Impeller and Shaft, 26 mtr head and 7.4 LPS, 415 volts, 3 phase, including suitable starter of for Back Wash at Filtration Plant with suitable starter and suitable size three core sheathed copper cable from pump set to starter complete all as specified and directed.Rates inclusive of foundation for motor and gear box, nuts and bolts etc with all fittings, wiring, cable etc as per site requirement.

Supply, fix, install and testing of Submersible Pump set suitable for 415 volts, 3 phase, 35M Head, 7 LPS not less than 5 HP including suitable DOL starter complete all as specified and directed.Rates inclusive of foundation for motor and gear box, nuts and bolts etc with all fittings, wiring, cable etc as per site requirement.

M&L for disconnection, shifting of 02 Nos Monoblock Pump set of capacity 5/7.5 HP with all accessories like starter, cable, inlet and outlet pipeline to a new location at Prothrapur Filtration plant as per site requirements, re-fixing the same with necessary PCC foundation complete all as specified and directed

Material and labour for PCC (1:2:4) Type B-1, using 20 mm graded stone aggregate as in foundation, filling mass concrete, for supporting / encasing of Pipe lines of any description, valve chambers, Pilasters, Columns, Pillars, Buttresses, retaining wall supports, Boundary Pillars and Posts including necessary form work etc complete all as specified and directed.

S& F in replacement steel water tubes medium grade (ISI marked) galvanised with all fittings and fixed to walls or laid on floor or in ceilings of size 20 mm bore pipe including taking out of old pipelines complete all as specified and as directed.

All as per item No 10 here in before but of size 25 mm bore pipe complete all as specified and as directed.

All as per item No 10 here in before but of size 40 mm bore pipe complete all as specified and as directed.

All as per item No 10 here in before but of size 50 mm bore pipe complete all as specified and as directed.

All as per item No 10 here in before but of size 80 mm bore pipe complete all as specified and as directed.

S&F in replacement Gun metal gate valve with iron wheel head screwed both ends for pipe of size 25 mm all as specified and as directed by Engr-in-Charge. Make : Zoloto, LEADER or eqvt.

All as per Item Sl Item No 15 here-in-before but of size 40 mm complete all as specified and as directed.

All as per Item Sl Item No 15 here-in-before but of size 50 mm complete all as specified and as directed.

S&F in replacement of 20mm CPVC pipes SDR 13.5 & Plain CPVC SDR 13.5 grade with all types of fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc as required at site, fittings on walls/ceiling or laying in floors complete all as specified and directed .

All as per Item Ser Item No 18 here-in-before but of 25mm CPVC pipes complete all as specified.

All as per Item Ser Item No 18 here-in-before but of 40 mm CPVC pipes complete all as specified.

All as per Item Ser Item No 18 here-in-before but of 50 mm CPVC pipes complete all as specified.

M&L for fabrication of MS sheet not less than 3 mm thick duly fixing with required size MS angle for valve chamber cover with plates of Fe 410W, Gde E-250, Quality-A Plain or chequered channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment with riveted, bolted or welded attachment for locking arrangements complete including painting with two coat of synthetic enamel paint black colour/shade over a coat of redoxide primer complete all as specified and directed.

M&L for fabrication of angle iron of any size for ladder/ valve chamber etc including painting with two coats of synthetic enamel paint Black /smoke grey colour/shade over a coat of red oxide primer complete all as specified and directed

Supplying, Installing, Commissioning and Testing of CPRI approved, Factory made, Free Standing Floor Mounted, Dust and Vermin proof LT Cubical Panel Board suitable for 415V, 3 Phase, 4 wire 50 Hz, Compartmentalised, Outdoor type, fabricated with 3.15mm thick CRCA Sheet and MS angle of size 60x60x6 mm frame front and back openable double door system lockable /openable by keys from both sides and shall be given pre-treatment for degreasing, phosphatising etc, 'U' type gasket shall be used to make the inner shell completely vermin proof and to accomodate MCCBs, TPN Aluminium Busbars of rating 1.5 times that of controlling MCCB. Busbar and extension link shall be insulated with color coded heat shrinkable sleeve and shall be mounted on suitable size SMC insulator at suitable inteval throghout the length of busbar, entire panel shall have a common earth bar of size 25mm x 5mm at the rear with 2 Nos earth stud, solid connections from main bus bar to switchgears with required size of aluminium bus bars. All internal control wiring with suitable copper cable of suitable size, cable alleys, cable gland, plates in two half and general construction confirming to IS:8623/93. Computer cut self adhesive vinyl danger notice plate having conventional symbol on the busbar chamber and front of outer shell and the degree of protection of outer shell shall be IP-54. The panel shall be fixed with angle iron frame made of angles of size 75 x 75 x 8mm at Corners and ISMC of suitable size for base, embedded 600 mm below ground level in PCC 1:2:4, Type B–1 using 20mm grade stone aggregate, 600 mm above ground level complete including connecting up with incoming and outgoing cables from bottom entry etc provision of lifting lugs of suitable size at top to lift the Panel safely shall be made. An inspection lamp with 5 watt LED bulb shall be fitted on top side of inner shell. The degree of protection for inner shell shall be IP-42 & including carry the following controls:-

INCOMING (a) MCCB, adjustable type, 4 poles, 415 V, Ics = 100% Icu, Lcu = 50 KA breaking capacity, rating 400 A including all fixing accessories with both ends spreader links - 01 No. OUTGOING (a) MCCB, adjustable type, 4poles, 415 V, Ics = 100% Icu, Lcu = 36 KA breaking capacity, rating 250 Amps including all fixing accessories with both ends spreader links - 02 Nos. (b) MCCB, adjustable type, 4poles, 415 V, Ics = 100% Icu, Lcu = 25 KA breaking capacity, rating 125 Amps including all fixing accessories with both ends spreader links - 03 Nos. (c) Blank Space for fixing 01 x Energy Meter. (Taking down /Refixing existing energy meter at site by the contractor) (d) Digital VAF Meter - 01 No (e) Indicating Lamp - 01 Set Make of MCCBs :- Siemens / Legrand / Schneider/L&T Note: (a) Contractor shall be submit panel drawing before placing order and approved from GE. (b) Rates for switch gears, fixing /connecting charges, PCC foundation all deemed to be included in the above items .

M&L for Glowsign board made of Aluminium composite panel (ACP) lighting glow type 540 GSM printed flex,rectangular shape of size 20 feet x 3 feet with 150 mm thicknes with SS framing of made with square pipe 40 mm in size in double sided powder qouted 24 gauge coated GI sheet, fixing arrangements with nut bolt / clamp complete as per site, electric wiring with PVC copper wire 2.5 sq mm and 6 Nos 20W LED light fitting in equal distance complete all as specified and as directed. Note- (i) Provide name, details of E/M instalation in front and rear as per approval by GE and cost to be included in qouted rates.

M&L for earthing complete with M.S. galvanized earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 M deep below normal GL) with top edge of the earth plate not less than 1.5M below normal GL, connected to galvanised strip 32 x 6mm as earth lead by means of bolts, nuts, washers and check nuts & washers of GI or steel incl excavation, PCC (1:3:6) type C-1 chamber with RCC cover (1:2:4) type B0, 40 mm thick reinforced with 6 mm dia bar, 3 Nos. both way, 40 mm dia light grade GI protection pipe, funnel with wire mesh,watering pipe of size 20 mm dia med. grade, lugs, main Earthing lead upto 7.5 mtr incl. Charcoal dust, salt etc. all as shown in electrical plate No. 3 of SSR Part-I, 2009 specification

All as per item No.27 here -in-before but earthing with 4 sqmm GI wire as earth continuty conductor complete all as specified and directed.

M & L in repair for Earth continuity conductor or main earthing lead of 32 x 6 mm galvanized iron strip, buried in ground or fixed to wall in repair complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness ( below or above ground level).

Demolition of Precast Concrete Block work built in Cement Mortar including all quoins arches pillars etc complete all as specified and as directed.

Dismantling floor, hearth or wall tiles including cement mortar bedding(but not backing) and removing serviceable tiles to stores and rubbish off the premises.

Taking down chowkats or frames(without taking off shutters from the frame) area exc 1.5 Sqm but n.exc 4.0 Sqm each.

Taking down chowkats or frames(without taking off shutters from the frame) area n exc 1.5 Sqm each.

Taking down and refixing in same or other opening chowkats or frames(without taking off shutters from the frame) area exc 1.5 Sqm but n.exc 4.0 Sqm each.

Surface excavation nexc 30 cm deep and averaging 15 Cm deep and getting out in any type of soil complete all as specified

Excavation in trenches not exceeding 1.5m wide and n exc 1.5m in depth for foundation etc n exc 10 Sqm on plan and n exc 1.5m in depth and getting out in any type of soil complete all as specified.

Excavation in post holes (or similar holes) each n.exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25 cm, watering and removing surplus soil to a distance n.exc 50 m and making good surface all as specified.

M&L PCC 1:3:6 type C2 (40 mm graded stone aggregate) in foundation filling and mass concrete or post holes all as specified.

M & L for cement concrete 1:4:8 type D2 ( using 40 mm graded stone aggregate) as in foundation, filling mass concrete complete all as specified and as directed.

M&L Hardcore with broken stone of guage n exc 63mm deposited spread and levelled in layers n exc 15 cm thk watered and rammed to a true surface complete all as specified.

M&L PCC 100 mm thick using 1:2:4 type B2 (40 mm graded stone aggregate) as in flooring of parking all as specified.

M&L sand filling under floors or in foundation including watering and consolidation complete all as specified and directed

M&L Machine pressed precast concrete interlocking paver block any shape and size conforming to IS-15658-2006 of 60mm thickness M-35 Grade and pointed with Grey cement and pigment complete all as specified and directed Note: sand/grit filling shall be measured and paid seperately

M&L for precast cement concrete solid block masonry with solid blocks using PCC 1:3:6, type C1 (using 20mm graded stone aggregate), exc. 10cm in width, set in CM 1:4 all as specified and as directed.

M&L Rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement.

S&F Steel works In tubular/ posts/ trusses/ purlin including special shaped washer etc.complete using ERW or induction butt welded tubes conforming to IS 1161-1797 grade St 240.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment etc and fixed by riveting or welding or with nut and bolts (including nuts and bolts) conforming to Fe-410-W grade E 251 Quality B complete all as specified and directed.

S&F Mild steel bolts exc 12mm dia and n exc 20mm dia purpose made with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. exc 30cm long all as specified.

M&L Painting to new steel and iron surfaces of exc. 10cm wide or girth by two coats of synthetic enamel paints over a coat of red oxide primer including preparation complete all as specified and as directed.

S&F 0.50 mm thick prepainted galvalume aluminium zinc coating GI based corrugated steel sheet of colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self taping screws as specified.

S&F 0.50 mm thick prepainted galvalume aluminium zinc coating GI based plain steel sheet of colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self taping screws as specified.

S &F MS work in wind ties for roof including securing bolts all as specified

Return filling in Surplus soil and back filling , including spreading, levelling, watering and well ramming in layers n.exc. 25cm complete all as specified and directed

Removing excavated soil n.exc 50 m and depositing where directed at level n.exc 1.50 m above the starting point complete all as specified and directed.

Use and waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick

M&L for RCC- M -30 Design Mix as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

Taking down cement plaster of any description on brick or concrete surfaces etc including racking out joints, hacking for key, scrubbing down with water etc.

M&L Rendering 5mm thick in CM 1:3 on soffits of RCC slabs, roof projections, soffits and sides of RCC beams, waist slab, Loft Slab, RCC shelves, Chajjas, and the like finished even and smooth without using extra cement.

M&L 15mm thick rendering in two layers of 10mm thick backing coat in CM 1:6 and 5mm thick floating coat in CM 1:4 mixed with water proofing compound on all external wall surfaces finished even and smooth without using extra cement. (Note : Water proofing compound shall be measured and paid seperately)

Supply only integral WPC (3% by wt of cement).

M&L for removing loose and broken concrete by chiselling/Picking wtc upto a depth of 10 to 20mm from floor/roof slab/chajjas and similar structural members cleaning the dismantled portion with wire brushes etc to remove dust dirt and other foreign particles including necessary scaffolding etc and removal of debris to a distance not ecxeeding 50m complete all as specified and as directed.

M&L for application of high build polymer modified cement mortar(1:2:5) mixed with 3kg SBR per bag of cement in ceiling surface 10 to 20mm thick in two layer over a coat of bonding agent Nito bond SBR (1Ltr SBR+1Ltr Water+3kg cement) complete all as specified and directed.

M&L for removing loose and broken concrete by chiselling/Picking wtc upto a depth of 50 to 100mm from column, beams and similar structural members cutting edges cleaning the dismantled portion with wire brushes etc to remove dust dirt and other foreign particles including necessary scaffolding etc and removal of debris to a distance not ecxeeding 50m complete all as specified and as directed.

Use and waste of Formwork to column, post and similar items including edges complete all as specified and as directed

M&L for non shrink cementitious micro concrete mixed with 12.5mm graded stone aggregate using Renderoc RG or equivalent as approved by GE (18 Kg Aggregate : 25 Kg Renderoc) respectively ( as per manufacturers instruction) laid in average thickness of 50 to 100 mm in situ complete all as specified and directed.

M & L for preparing newly plastered wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of putty complete all as specified and as directed.

M & L for preparing newly plastered ceiling surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of putty complete all as specified and as directed.

M & L for preparing old plastered ceiling surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of putty complete all as specified and as directed.

M & L for complete removal of existing treatment on old plastered wall surfaces and applying two coats of oil bound distemper over a coat of resistant primer over a coat of putty complete all as specified and as directed.

M& L for Finishing walls with Acrylic smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) etc complete all as specified (Make Apex Ultima)

M& L for Finishing walls with Acrylic smooth exterior paint of required shade : Old Surface (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) etc and preparation of old surface complete all as specified (Make Apex Ultima)

M&L Light shade Vitrified ceramic tiles 10mm thick (Square/rectangular) area of each tile n exc 0.36 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in cement mortar (1:6) all as specified and directed.

All as per item no 75.00 here in before but in skirting/dado laid over 10mm thick cement plaster in cement mortar 1:4 complete all as specified

M&L 40mm thk cement concrete type B-1 1:2:4(Using 20mm graded stone aggregate) in sub base of flooring/hard standing complete all as directed

M&L for 18 to 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite

S&F 110mm bore PVC (SWR) soil, waste and vent pipe, in any length , with rubber joints, laid in trenches or in floors

S&F 110mm bore PVC (SWR) soil, waste and vent pipe, in any length , with rubber joints, fixed in walls

S&F in repair PVC (SWR) 110mm dia bend of any radius.

S&F in repair PVC (SWR) 110mm dia double T equal or unequal at Junctions of any radius.

Dismantling boarding/Frame work of any description, fixed in any position with nails/screws.

S & F Aluminium anodised (minimum anodisation is 50 microns) Door / window / Ventilator/partition frames and shutters (02 Nos glazed & gauzed), side hung type, without sash bars,standard aluminium grills, with panel inserts of sheet glass, gauze including necessary joining cleats, glazing clips, rubberbeading, Neoprene packing, anodised aluminium snap beading, screws, imax hinges,butt hinges,handles, locking arrangements etc., complete with standard aluminium sections, complete all as specified and as directed .(Aluminium section shall be of make Jindal/Hindalco/ Indalco). (Note:- Weight of various Aluminium sections handles and locking arrangements shall only be considered for measurement for payment. However cost of rubber packing given in the item shall be deemed to be included in the rate quoted. Glass panels, prelaminated particle boards, aluminium wire cloth as applicable will be measured and paid separately).

S&F 24 Inches(maximum) Telescopic Drawer channels stainless steel Rust free 600mm Ball bearing soundless office Table drawer slides pack of 1 set(2 Pcs)

Supply and fix aluminium composite panel sheet of 3 to 4mm thick as in cupboards, wall cladding & false ceiling fixed on aluminium frame work with plastic strips (Double sided sticker) of suitable size of varying thickness of 10mm to 30mm excluding aluminium frame work applying adhesie over aluminium screws. The joints in panels shall be filled with weather proof sealant, the board shall be stuck with a layer of any colour high intensity reflective grade polymer sticker installed using epoxy adhesive complete all as specified and as directed.

Supply only 4.0mm thick sheet glass, ordinary quality in squares exc 0.50 sq.m in each panel.

Supply only aluminium alloy wire mesh 0.45mm nominal dia of wire and average width of apeture 1.4mm fixed with aluminium wire staples etc.complete all as specified and as directed

Supply only 5.50mm thick sheet glass, ordinary quality in squares exc 0.50 sq.m in each panel.

Supply only 150mm aluminium anodised barrel tower bolts of extruded section and fixed.

Supply only 250mm aluminium alloy anodised sliding bolts with hasp, staple and fixing clips of sheet, cast or extruded section fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed.

Supply only Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified

Supply only 125mm aluminium handles, cast type , anodised.

Supply and fix 150 mm aluminium handles, cast type , anodised.

S&F Butt hinges of size 50mm medium weight cold rolled mild steel

S&F mild steel 40mm dia brass polished cupboard knobs fixed with nut, screw and washer off

S&F 75 mm long extruded aluminium alloy handles fabricated type anodised

Material and labour for false ceiling with aluminum grid work (Size of grid 600x600 mm) with 35 x 25 x 1.5 mm main tee and 25 x 25 x 1.4 mm cross tee and wall angle and suspended with 2mm dia GI wire hooked to roof with needful adjustment bolts at an interval of 1.20 m centre to centre staggered and board with Eco board decorative type size 600 x 600 x 4 mm thick finished with two coats of oil bound distemper over a coat of primer on exposed surfaces all as specified and directed

M&L Point wiring complete with 1.5 sqmm single core FRLS PVC insulated and unsheathed cable 1100 volts grade with multistranded copper conductor drawn through and including PVC casing and caping and all accessories fixed to walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm copper cable green in colour as earth continuity conductor and connected to common earth dolly, including fabricated steel terminal box made out of 1.60mm thick MS sheet concealed in walls, with 3mm thick laminated sheet top cover for housing the switches, socket outlets,fan regulators etc., all as specified and as directed forthe following:- (a) One light point controlled by one switch

(b) All as per item no 99.00 here in before One fan point controlled by one switch and one regulator

(c) All as per item no 99.00 here in before One 3 pin switch socket outlet point 5 amps on independent board

Supply and fix switch piano flush button single pole oneway 5 amp complete all as specified and as directed.

Supply and fix switch socket combination 3 & 2 pin (multi pin) 5 amp flush type complete all as specified and as directed.

Supply and fix ceiling rose surface bakelite 65x50mm 3 terminal complete all as specified and as directed.

Supply and fix fan speed regulator, electronic suitable socket type for single phase AC, 240 volts, 50 Hz,100 watts, complete all as specified and as directed by Engineer-in-Charge

Supply and fix ceiling fans, complete with three blade, down rod, accessories 230V, 1200mm sweep, with Squirrel cage induction motor complete all as specified and directed.

Supply and fix in repair metal enclosure distribution board SPN, 4 way 240 volts, with 200 amps rated bus bar, double door suitable for mounting MCBs including taking down old MCB/DB complete all as specified and directed. Note-: Incoming & outgoing connections from the DB shall be provided with proper lugs/ thimbles etc.

Supply and fix in repair MCB single pole 240 volts, 6 to 32 amps "C" series complete all as specified and as directed by Engineer-in-Charge

Supply and fix single pole and netural 240 Volts 32 amps complete all as specified and as directed by Engineer-in-Charge

Supply and fixing energy efficient aluminium housing LED Smart bright batten 22 /20 Watt mounted batten fitting 4ft in length nano diffuser technology to ensure minimum loss in light transmitted, long life of over 30000 hours including lamp and connecting with twin core shethed cable from fitting to ceiling rose all as specified and as diected.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less thab 1.5 Meter below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts , check nuts and washers of GI and GI tubing 20 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as specified and directed electrical plate No. 3 of SSR part - I.

supply & Lay XLPE insulated, heavy duty 1100 volt grade electric armoured LT UG cable with aluminium conductor of size 16 Sqmm 4 Core in trenches/along the wall/including making all connections, saddles, spacers including scaffolding if any required for saddling the cable in walls of building of height up to 25 meter, complete with aluminium lugs as required at site and as directed by Engr-in-Charge

Supply & lay cable protection pipe of HDPE double wall corrugated (DWC) incl couplers,bends etc of size 50 mm OD and ID 38mm confirming to IS 14930 -II and ISI Marked all specified and directed.

S&F tube light grade galvanised with all fittings laid in trenches of following size of 50 mm bore.

Material and Labour for cutting bituminous road at a width not more than 30cm and a depth not exceeding 60 cm for laying of pipes on road crossing for cable protection and making good with cement concrete 1:2:4, type, B-2 to match the existing surfaces of the road all as specified and as directed by Engineer in charge.

BABBAR ENGINEERS (BID ID -3126132)

SKV Engineering (BID ID -3125120)