SPL REPAIRS TO BASKET BALL COURT NEAR COMD STADIUM, SPL REPAIR TO BLDG NO. T-669 (NO. 2 PI), JOINERY, FALSE CEILING AND INTERNAL ELECTRIFICATION AT CERTAIN UNIT, PROVN OF OR SHELTER NEAR BLDG NO. P-24 AT CERTAIN UNIT AT FORT WILLIAM UNDER GE (FW) KOL

Amount

SCHEDULE 'A' PART-I (B/R WORKS)

Demolition of Brick Work built in Cement Mortar including all Quoins, Arches, Pillars, etc. of any descriptions, complete all as specified and as directed.

M&L Brick Work with fly-ash Bricks (with Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed.

M&L Brick Work with fly-ash Bricks Half-Brick thick, Old Size, built in Cement Mortar 1:4, Straight or Curved on Plan to any Radius, complete all as specified and as directed.

M&L Rendering 15mm thick, on fair faces of brick or concrete surfaces of walls in cement mortar 1:4, finished even and smooth without using extra cement complete all as specified and directed.

Demolition Cement Concrete (un-reinforced) in Ground Floors and Paving not exc. 150mm thickness (above or below Ground Level), complete all as specified and as directed.

M&L for providing Plain Cement Concrete (1:1½:3), type A1, using 20mm graded stone aggregate as in flooring complete all as specified and directed.

M&L for providing Plain Cement Concrete (1:2:4) type B1, using 20mm graded stone aggregate as in footpath, sub base of floor complete all as specified and directed.

M&L forming 12 mm thick expansion joints filled with pre-formed bituminous filler and top 30 mm primed and sealed with sealing compound Grade 'A', for 150 mm thick concrete complete all as specified and directed.

M&L for forming construction joints 30 mm deep x 10 mm wide filled with sealing compound Grade 'A' complete all as specified and directed.

M&L PCC 1:3:6 type C2 (Using 40 mm graded stone aggregate) in Foundation, filling and mass concrete complete all as specified and as directed.

Supply and laying of basketball court flooring in one layer resurface with 4 layers rubber cushion course and one layer filler finishing course and 2 coats colour coat for line marking and painting to surface with approved colour of acrylic paint etc complete all as specified and directed. (MAKE: COSTA SPORTS SYSTEM PVT LTD / REBOUND ACE INDIA PVT LTD / SUNDEK SPORTS SYSTEM) (NOTE: The work shall be got carried out by authorised workmen/ applicator of the manufacturer)

Supply and installation of basketball acrylic board 18mm thick, transparent acrylic sheet of international size 180 cm x 105 cm, fixed to existing pole in suitable position of pole and ball net ring, made up of flexible steel rods capable of withstanding hoops including nylon net etc complete all as specified and directed. (MAKE: SUNACRYILIC / METCO / COSCO / NIVIA or any other reputed manufacturer as approved by GE)

M&L for applying one coat of synthetic enamel paint to old decorated steel surfaces of any description over 10 cm width or girth including preparation of surfaces all as specified and directed by Engineer-in-Charge.

M & L for plain cement concrete (1:2:4) type B2 using 40 mm graded aggregates in surface channels and drains complete all as specified and directed.

M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi tred/stopped ends etc.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed (NOTE: Quoted rate shall be deemed to be inclusive of the cost of sand cushioning)

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed

Dismantling of ceiling board incl snap grid frame of any thickness including cover fillets complete all as specified and directed.

S&F Suspended metal grid Ceiling System with mineral fibre acoustic tiles as per following specifications:- a) Ceiling Tiles:- Mineral fibre acoustic tile of 16mm thickness having sand textured finish with acoustical punchers, bevelled tegular edge and 8mm drop in module size of 600 x 600mm. Tiles shall have humidity resistance (RH) of 99%, NRC 0.50 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 standard, CAC of 33db as per ASTM E1414, Light Reflectance ≥85% as per ASTM E-1477, Thermal Conductivity k = 0.052 - 0.057 W/mK, Colour Global White, Fire Performance of class 0/1 as per BS 476 Part 6/7 and Class A as per ASTM E84. b) Metal Grid:- The grid system shall be 15 mm wide T - section flanges colour global white (matching to tile color) having roll formed double stroke rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm (all sections). The deflection loading of the system shall be 12.5 kg/m2 (as per standard installation layout mentioned below) and main beam tested as per ASTM C635 (Deflection limit less than L/360) with a deflection loading of 15kg/m. The end details of the cross tee shall be made of pre hardened steel and fixed to the ends of the cross tee to provide double locking between “cross tee to cross tee” and “cross tee to main beam”.

(Item No. 1.19 Contd....) All main beam to main beam and cross tee to cross tee connection shall have a pull out strength of more than 100kg. The T Sections shall be made of hot dipped galvanized steel of 90 gsm as per IS 277 (2003) and pre-painted steel with baked polyester paint with 0T bending capability. The ceiling grid sections shall be fixed to ceiling with 6 mm dia GI hangers upto required length by means of ceiling cleats made out of GI flat 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5mm dia 40 mm long. MAKE OF CEILING GRID : ARMSTRONG, Model: SUPRAFINE 38 or equivalent in GYPROC / USG BORAL / UNISTEEL MAKE OF CEILING TILES: ARMSTRONG, Model: DUNE or equivalent item in GYPROC / USG BORAL / U TONE)

Dismantling wrought iron or mild steel work of any description in rafters, purlins and wind ties wtc complete all as specified and directed.

M&L for structural steel work Fe 410-W (Gde-E-250) quality-A in roof trusses (framed), trussed, purlins, crane gantries, rials and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and as directed by the Engineer-in-Charge. (NOTE: Quoted rates shall be deemed to include for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete)

M&L Preparing new Steel or Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint over a coat of Red Oxide/ Zinc Chrome Primer, complete all as specified and as directed.

Dismantling of plain corrugated steel sheeting any gauge, thickness, including nainital or similar pattern roof covering & removing off the site.

S&F 0.50 mm thick TCT (total coated thickness) pre-coloured Galvalume sheets with minimum base metal thickness of 0.45 mm, single skin high rib/multi rib profile Galvalume sheeting having 1000-1020 mm width and 28-30 mm high crest @ maximum 250-255 mm pitch (centre) with sheets manufactured out of 0.50 mm this TCT (total coated thickness) high tensile Galvalume sheets having tensile strength 550 MPA with 18-20 micron top coat over 5 micron primer and 8-10 micron alkyld backer zinc aluminium alloy AZ-150, sheets having a dip metallic zinc (43.5%0 aluminium (55%) & silicon (1.5%) with total mass coating of 150 gms/sqm on both sides, having wide pans with minimum 3 small stiffening ribs for effective water shedding and special male/female ends with full return legs on laps for purlin support and fixed as per existing profile of roof complete all as specified and directed.

All as per Item No. 1.25 above but 0.50 mm thick coloured plain Galvalume sheet as in ridge/valley gutter of roof.

Dismantling stone slabs and tiles, laid, bedded and ointed in any mortar of any description or thickness in floors, aprons etc all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as directed.

M&L 25 mm thick pre polished coloured chequered tiles of size 400mm X 400mm, jointed and pointed in neat cement slurry with white or coloured to match the shade of tiles, laid over and including 20 mm thick screed bed in cement mortar 1:6 completed all as specified and directed.

M&L for laying and fixing Machine cut kota stone slab flooring 20-22mm thick over 20 mm thick cement screed base (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for laying and fixing Kota stone slab 20-22mm thick in riser of steps, skirting, dado and pillar laid over 10 mm thick cement screed in cement mortar 1:3 and jointed etc complete all as specified and directed.

M&L granite (of any type) work, 18-20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, urinal partition and like in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and making moulds on edges laid over and including 20 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for vitrified ceramic tiles light shade 10mm thick (square/ rectangular) polished area of each tile not exceeding 0.36 Sqm in floors etc set and joined in neat cement slurry and pointed in colored cement to match over 15 mm thick screed bed of cement mortar 1:4 complete all as specified and directed..

All as per Item No. 1.33 here-in-before but light shade vitrified tiles in skirting over 10 mm thick backing coat in cement mortar 1:4

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key and scrubbing down with water complete All as specified and as directed.

M&L for complete removal of old distempered surfaces of walls and applying 2 mm thick wall putty over plastered surfaces, finishing surfaces even and smooth and applying two coats of acrylic distemper over a coat of alkali resistant primer as per manufacturer's instructions complete all as specified and directed.

M&L for applying 2 mm thick wall putty over newly plastered surfaces of walls, finishing surfaces even and smooth and applying two coats of acrylic distemper over a coat of alkali resistant primer, as per manufacturer's instructions complete all as specified and directed.

Material and labour for complete removal of existing treatment and applying two coats of exterior acrylic weather proof emulsion paint over a coat of alkali resistant primer to old decorated surfaces of walls of any description, over 10cm width or girth not otherwise described, complete all as specified and as directed.

M&L for preparation of old painted wooden surface of any description over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed.

Taking down chowkats of frames with shutters (without taking off shutters, from the frames) not exceeding 1.50 Sqm each and removing off the site complete all as specified and as directed.

Taking down chowkats of frames with shutters (without taking off shutters, from the frames) exc 1.50 Sqm but n exc 4.0 sqm each and removing off the site complete all as specified and as directed.

S&F for 2nd class hardwood, plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, moulded or chamfered, put together with glue, pinned at joints complete all as directed.

S&F Factory made 35mm thick with 2nd class hard wood, rail and style factory made plain framed panelled shutter(two panel) with lock, rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail & style as per IS:1003(Part-I) kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 35mm thick Factory made 2nd class hard wood glazed & skeleton shutters, open rebated and prepared to received glass, gauge etc.(without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part-I section 8, clause 8.20(a) complete all as specified and directed.

S&F 30mm thick Factory made 2nd class hard wood glazed & skeleton shutters, open rebated and prepared to receive glass, gauge etc.(without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc, size of members of shutters as specified in SSR Part-I section 8, clause 8.20(a) complete all as specified and directed.

S&F 4mm thick ordinary quality plain sheet glass and glazing in square n.exc. 0.5 Sqm in each pane complete all as specified and directed.

S&F stainless steel wire cloth, 0.65mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 100mm butt hinges heavy weight, cold rolled mild steel, fixed to shutters etc complete all as specified and directed.

S&F 75mm butt hinges heavy weight, cold rolled mild steel, fixed to shutters etc complete all as specified and directed.

S&F 300mm aluminium, anodised sliding door bolt with hasp, staple(bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy all as directed complete all as specified and directed.

S&F Extruded aluminium alloy handles, fabricated type, anodised, 150 mm complete all as specified and directed.

S&F Extruded aluminium alloy handles, fabricated type, anodised, 100 mm complete all as specified and directed.

S&F 150mm aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 100mm aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

M&L for plain cement concrete (1:2:4) type B1 using 20 mm graded aggregates in roof kerbs or mud stops, rounded or chamfered on edges including formwork complete all as specified and directed.

Cutting out concrete blocks, slabs, brickwork or stone masonry (in alternate course), forming tooth-ings for and bonding new work in mortar into old work, including new materials entering old wall, cement concrete 1:2:4, type B1 (using 20 mm graded stone aggregates) set in cement mortar 1:4 complete all as specified and directed.

M & L for hardcore of gauge not exc 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to true surface with broken stones complete all as specified and directed.

Materials and Labour for 100 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded aggregates as in floors and paving etc., complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6 type C2 (using 40mm graded crushed stone aggregate) as in plinth protection, finished even and smooth without using extra cement as directed by the Engr-in-Charge.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L Rendering 10 mm thick, on fair faces of brick or concrete surfaces of walls in cement mortar 1:4, finished even and fair complete all as specified and directed.

M&L Rendering 15mm thick, on fair faces of brick or concrete surfaces of walls in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and directed.

M & L for RCC 1:1½:3, type A1, using 20 mm dia graded stone aggregates as in Beams, cantilevers, lintels over 1.5 M span complete all as specified and directed. (NOTE: MS reinforcement shall be measured and paid separately)

M&L RCC 1:1½:3, type A1, using 20 mm graded stone aggregate as in chajjas etc complete all as specified and as directed. (NOTE: MS reinforcement shall be measured and paid separately)

M&L TMT Bars 10 mm dia and over, cut to length, bent to shape required including crank-ing, bending and binding with and including Mild Steel Wire (annealed) not less than 0.90 mm, complete all as specified and as directed.

M&L for TMT bars 5 mm dia and over upto and including 10 mm dia in stirrups , spacers and binders cut to length , bent to shape required as in reinforcement and binding with MS wire ( annealed ) not less than 0.90 mm dia complete all as specified and directed .

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressumers, lintels, cantilevers, shelves etc for fair finished surfaces complete all as specified and directed.

M&L for formwork to chullah hoods, chajjas, troughs and similar items including edges for fair finished surfaces complete all as specified and directed..

M&L for preparation of new plastered of ceilings and applying two coats of acrylic distemper over a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation of new plastered of ceilings and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

M&L mild steel work in tubular trusses including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS-1161:2014 grade St-240 complete all as specified and directed. (NOTE: Quoted rates shall be deemed to include for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete)

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment all as specified rolled mild steel in stairs (framed) including stringers, treads landing, balusters, hand rails etc including cleats, brackets etc complete all as specified and as directed.

Material and Labour for applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

S&F Mild steel ordinary rat tail rod pattern springs including roller and roller plate, 300 mm complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor. 140mm overall length of cover plate complete all as a specified and as directed

Supply and Fix for galvanized, plain mild steel sheeting 1.0 mm thick, with minimum zinc coating of 120 gram/Sq m, as in ridge, hips, valley gutters, drip and straight flashing, complete all as specified and directed.

M&L for false ceiling with 'E' board "Classic", reinforced, designer series, board with HPSC of size 600 mm x 600 mm x 4 mm thick fixed on aluminium snap grid to support the boards/files with aluminium anodised main 'T' section 36mm x 25mm x 1.40mm cross tee 23.50mm x 23.50mm x 1.40mm thick and aluminium angle 25mm x 25mm x 1.40mm as on edges/sides, fixed to ceiling with hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long and applying two coats of oil bound distemper over a coat of primer on exposed surfaces complete all as specified and as directed. (NOTE: Quoted rate shall be deemed to be inclusive of the cost of ceiling board)

M&L for damp proof course to horizontal or vertical surfaces 25 mm thick including necessary formwork in cement concrete 1:2:4, type B0 using 12.5 mm graded stone aggregates complete all as specified and directed.

M&L for applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cum per sqm complete all as specified and directed.

Excavation in trenches not exc 1.5 metre width and not exceeding 1.5 metre in depth in soft/loose soil and getting complete all as specified and as directed.

Returning, filling in including spreading levelling watering and well ramming in layers n.exc 25 thick for soft/loose soil complete all as specified and as directed.

Removal of excavated material to a distance n.exc 50 metre and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed.

SCHEDULE 'A' PART-II (INTERNAL ELECTRIFICATION WORKS)

Taking down copper/ aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets etc excluding light fitting for reuse or removing from site and making good disturbed surface of walls, floors etc.complete all as specified and directed.

Taking down of Old MCB DB any type any size including MCCB/RCCB/MCBs and disconnecting the serviceable MCBs and keeping in safe custody for reuse at site or removal from site complete all as specified and directed.

Taking down of old Sub main wiring any type including batten/ conduit/ casing at any indicated situation complete all as specified and directed.

M&L for concealed type point wiring with 1.50 Sq. mm (nominal area) FRLS-H PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and including PVC conduit complete with all fittings and accessories, fixed to walls/ceiling, including mild steel terminal boxes 1.25 mm thick conforming to IS-5133 (Part-I) with 3.0 mm thick plastic laminated sheet top cover (ISI Marked) for mounting switches/ regulator /bell push etc and including 1.50 Sq. mm (nominal area) FRLS-H PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly, for one light point /bell point/ ceiling fan/exhaust fan point controlled by one way switch complete all as specified and directed. (NOTES: - (i) Where tube light fitting is to be fitted/suspended, CI Circular boxes shall be provided with the PVC Pipes in the ceiling & the unit rate shall be deemed to be included for the same. (ii) Cost of cutting chases for concealed wiring shall be deemed to be inclusive in the quoted rates. No claim in this regard shall be entertained at a later stage)

All as per item No. 2.04 above but for one 5 amps switch socket outlet on same board controlled by another switch, complete all as specified and directed (concealed type point wiring with terminal box).

All as per item No. 30 above but for one 5 amps switch socket combination on independent board, complete all as specified and directed (concealed type point wiring with terminal box).

All as per item No. 2.04 above but using 2.5 sqmm single core multi stranded copper conductor FRLS-H PVC insulated and unsheathed, cable for 3/6 pin 15 Amp socket outlet controlled by one switch on independent board with and incl 2.5 sqmm green FRLS-H PVC insulated and unsheathed, copper conductor as continuous earth wire with lugs complete all as specified and directed (concealed type point wiring with terminal box).

S&F new Switch piano, flush type, one way 5/6 Amps, Single Pole, 240 Volts complete all as specified and directed

S&F new switch socket combination outlet, 3 pin, flush type (non-shuttered) 5/6 Amps, 240 Volts complete all as specified and directed

S & F new socket outlet, 2 in 1, 3 pin, flush type (non-shuttered) 5/6 Amps, 240 Volts complete all as specified and directed

S & F new switch socket combination outlet, flush type (non-shuttered) 6 in 1, 3 pin, 6/16 Amps, complete all as specified and directed

S&F stepped type electronic fan regulator, flush type 5 Speed Control, 230/240 Volts complete all as specified and directed.

S&F lamp holder, PVC/Polycarbonate body with back plate suitable for batten/pendant fittings or to be mounted on walls complete all as specified and directed.

S&F new Ceiling rose, 3 terminals, 240 volts, surface type complete all as specified and directed.

S&F in repairs surface mounted LED luminaries, 1 X 20 Watt in aluminium housing, operating voltage 180-270 V, with acrylic/polycarbonate diffuser & integrated constant current electronic driver complete with all other accessories internally prewired and including connecting up with three core flexible copper wire of suitable size complete all as specified and directed. complying with the following specifications:- (a) minimum efficacy 110 lumen/watt (b) CRI not less than 80, (c) THD < 20% (c) having in built short circuit and surge protection (d) colour temperature not less than 5700 degree K (e) life not less than 25000 hours of operation

Taking down ceiling fan 1200 mm to 1400 mm sweep of any make sealing cable ends, dismantling blades, applying one coat of synthetic enamel paint by spraying after cleaning thoroughly with kerosene oil including filling cavities with filler etc, hanging the ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan, complete all as specified and as directed by Engr In Charge.

Taking down exhaust fan 200 mm to 450 mm sweep of any make sealing cable ends, dismantling blades, applying one coat of synthetic enamel paint by spraying after cleaning thoroughly with kerosene oil including filling cavities with filler etc, refixing the same in original position including provision of cable from ceiling rose or connector to fan, complete all as specified and as directed by Engr In Charge.

S&F TPN DB, IP 43 protection, double door (premium quality), 415 volts, 4 way (8+12), with 100 Amps copper bus bar for each phase complete all as specified and directed. (MAKE : L&T, Cat No. DBTPN004DD / LEGRAND, Cat No: 507670 / SCHNEIDER, Cat No. A9HTND04 / ABB, Cat No: E-SHDB M4 / PANASONIC, Cat No: BQS 304H / HAGER, Cat No: VYT04DH)

Supply and Fix, Double Door, Sheet Metal Enclosure for DBs (Premium Quality), for mounting of MCB for 240 Volts, 8 way, with 100 Amps rated copper bus bar, Single Pole & Neutral, complete all as specified and directed. (MAKE : L&T, Cat No. DBSPN008DD / LEGRAND, Cat No: 507611 /ABB, Cat No. E-SHC M 8 / SCHNEIDER, Cat No. A9HSND08 / HAGER, Cat No: VYS08D)

S&F SPN DB, IP 43 protection, double door (Premium Quality), 240 volts, 4 way, with 100 Amps copper Bus Bar complete all as specified and directed. (MAKE : L&T, Cat No. DBSPN004DD / LEGRAND, Cat No: 507610 / ABB, Cat No. E-SHC M4 / SCHNEIDER, Cat No. NBKRENSNDD04 / HAGER, Cat No: VYS04D)

S&F MCB (premium quality), 'C' series, TPN, 415 volts, 63 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / PANASONIC / HAGER)

S&F MCB (premium quality), 'C' series, SPN, 32 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / PANASONIC / HAGER)

S&F MCB (Premium Quality), 'C' series, single pole, 6 to 32 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / PANASONIC / HAGER)

M&L earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.5M below normal ground level connected to galvanized steel earth wire 4 mm dia (upto 7.5 metres) by means of bolts, nuts check nuts and washers of galvanized steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 45 cm x 45 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm centre to centre both ways, with one handle for lifting made out of 8 mm dia MS bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 40 mm bore galvanized steel tubing medium grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown in Figure 15A of IS 3043 :1987, complete all as specified and directed.

M&L for sub main wiring with 2 run of FRLS-H PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm along with one run of FRLS-H PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm as earth continuity conductor drawn through and including PVC casing-capping of suitable size, surface type complete all as specified and directed. (NOTE : Three runs of single core 4.0 sqmm cable & one run of PVC casing capping shall be measured as one unit)

S&F in repair Bracket/Arm suitable for street light fittings, made out of 32 mm bore (light grade) GI pipe length not exceeding 1.2 metre long, fixed with 02 sets of flat iron clamp of size 32mm x 6 mm, with bolts, nuts and washers of suitable size including applying two coats of aluminium paint over a coat of red oxide zinc chrome primer incl taking down existing bracket complete all as specified and as directed.

S&F in repairs LED Street Light fitting, 24/25 Watt capacity, in high pressure die cast aluminium housing with prismatic polycarbonate modular secondary lens optics with integrated constant current electronic driver, top opening driver cover, IP66 ingress protection, impact resistance of IK08 complete all as specified and directed and complying with the following specifications:-. (a) minimum system efficacy 120 lumen/watt (b) CRI not less than 70, (c) THD < 10% (d) Power Factor not less than 0.90 (e) having in built short circuit and surge protection upto 4 kV (f) having 10 KV external surge protection (for 45 watt & above) (g) colour temperature not less than 5700 degree K (h) life not less than 50000 hours of operation (MAKE: BAJAJ, Cat No: ENXT P 24L WH CR PC SD or equivalent model in other makes specified in tender) NOTE: Wire for electric connection shall be measured and paid separately)

-ditto- but street light of capacity 35/36 watt (MAKE: BAJAJ, Cat No: ENXT P 36L WH CR PC SD or equivalent model in other makes specified in tender)

M&L for surface type point wiring with 1.50 Sq. mm (nominal area) FRLS-H PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and including PVC casing capping medium duty complete with all fittings and accessories, fixed to walls/ceiling, including mild steel terminal boxes 1.25 mm thick conforming to IS-5133 (Part-I) with 3.0 mm thick plastic laminated sheet top cover (ISI Marked) for mounting switches/ regulator /bell push etc and including 1.50 Sq. mm (nominal area) FRLS-H PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly, for one light point /bell point/ceiling fan/exhaust fan point controlled by one way switch complete all as specified and directed.

All as per item No. 2.29 above but for one 5 amps switch socket outlet on same board controlled by another switch, complete all as specified and directed (surface type point wiring with terminal box).

All as per item No. 2.29 above but for one 5 amps switch socket combination on independent board, complete all as specified and directed (surface type point wiring with terminal box).

All as per item No. 2.29 above but using 2.5 sqmm single core multi stranded copper conductor FRLS-H PVC insulated and unsheathed, cable for 3/6 pin 15 Amp socket outlet controlled by one switch on independent board with and incl 2.5 sqmm green FRLS PVC insulated and unsheathed, copper conductor as continuous earth wire with lugs complete all as specified and directed (surface type point wiring with terminal box).

S&F in repairs recess mounted slim-fit down lighter, round or square, having glare free frosted diffuser, operating voltage 180-270V, with constant current electronic driver complete with all accessories with and including 15 Watt LED and including all accessories, mounting frame etc and connecting up with three core flexible copper conductor wire of adequate size complete all as specified and directed and complying with the following specifications:- (a) minimum efficacy 105 lumen/watt (b) CRI not less than 80, (c) THD < 20% (c) having in built short circuit and surge protection (d) colour temperature not less than 5700 degree K (e) life not less than 25000 hours of operation (f) Weather protection: IP20

Supply and Hanging, ceiling fan, with brushless DC motor, 1200 mm sweep with remote, down rod, canopy, fan blades and accessories and connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 1.0 Sq mm, 3 core, 1100 Volts grade, from ceiling rose/ connector to fan including dismantling existing fan complete all as specified and directed. (MAKE : USHA, Model: ENERGIA 32 / CROMPTON GREAVES, Model : ENERGION HS / ORIENT, Model: ECOTECH / PANASONIC, Model: BLDC F-12XDA / HAVELLS, Model: Efficiencia Neo) NOTE: Old fan, if any taken down, shall be deposited by contractor in MES store yard

Supply and fixing ventilating fan, 250 mm sweep, made of sturdy engineered plastic with louver shutter, 230 Volts, 50 Hz, connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 1.50 Sq mm, 3 core, 1100 Volts grade, from ceiling rose to fan complete all as specified and directed. (MAKE : HAVELLS, Model : Venti Air DX / CROMPTON, Model : Brisk Air / USHA, Model: CRISP AIR or equivalent model in BAJAJ / ORIENT / POLAR)

SCHEDULE 'A' PART-III (EXTERNAL ELECTRIFICATION WORKS)

M&L for sand cushioning/sand covering for underground cable protection and consolidated and compacted with clean dry sand complete all as specified and as directed. (NOTE: Punned thickness shall be measured for payment)

M&L bricks with sub class 'B' locally available laid in trenches above sand cushioning for cable protection complete all as specified and as directed.

Taking down unserviceable LT cable for repair/ replacement etc (from cable duct/underground trench / pole), stacking properly (cable, pipe and bricks) of size 10 sqmm 2 core complete all as directed by the Engr-in-Charge. (Note :- Necessary earth work to be measured and paid separately.

Supply, Laying and testing XLPE insulated, screened PVC bedded, galvanised steel strip or wire armored electric power cable 1100 Volts grade with stranded aluminium conductor of size 10 sqmm 2 core, laid in trench or fixed to wall/passing through pipe/pole complete all as specified and directed. (Note :- Necessary earth work to be measured and paid separately.

S&F in repair GI tubing 50mm bore (light grade) in trenches/floor/fixed along pole for cable/earth strip protection with proper size of clamp, nuts and bolts or for fixing lightning conductors etc all as specified and as directed by Engineer-in-Charge.

S&F GI tubing 40mm bore (light grade) in trenches/floor/fixed along pole for cable/earth strip protection with proper size of clamp, nuts and bolts or for fixing lightning conductors etc all as specified and as directed by Engineer-in-Charge.

S&F in repairs LED Flood Light fitting, of 150 watt capacity, in high pressure die cast aluminium housing with prismatic polycarbonate modular secondary lens optics with integrated constant current electronic driver and toughened glass cover, IP66 grade ingress protection, impact resistance IK07 complete all as specified and directed and complying with the following specifications:-. (a) minimum system efficacy 120 lumen/watt (b) CRI not less than 70, (c) THD < 10% (d) Power factor not less than 0.90 (e) having in built short circuit and surge protection upto 4 kV (f) having 10 KV external surge protection (g) colour temperature not less than 5700 degree K (h) life not less than 50000 hours of operation

S&F PVC insulated multistranded copper conductor wire, 2.5 sqmm 3 core, round flexible for connection of light fittings complete all as specified and as directed.

M&L for PCC (1:2:4) type B-1 using 20 mm graded crushed stone aggregate as in coping of poles / pipes / strip alignment etc using necessary formwork and finishing the exposed surfaces even and smooth without using extra cement, including demolition of existing concrete complete all as specified and as directed.

S&F polycarbonate junction box with metric knockouts, dust / water proof and with IP 66 protection for mounting on the street light pole of size 180 mm x 130 mm x 77 mm with Bakelite terminals (05 Nos), suitable for 10 Sqmm cable complete with suitable size cable gland and locknut fixed to pole with flat GI clamp of size 30 x 5 mm (02 Nos per pole), with suitable size nuts bolts & washers complete all as specified and directed. (MAKE : HENSEL, Cat No. KF 1010 B or equivalent model in SPELSBERG / SCHNEIDER / RITTAL)

M&L for cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling hole for bolts, in any shape of size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of aluminium paint including dismantling of existing unserviceable cross arms etc complete all as specified and as directed.

Materials and Labour for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.5M below normal ground level connected to galvanized iron strip 25 X 4 mm (upto 7.5 metres) by means of bolts, nuts check nuts and washers of galvanized steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 45 cm x 45 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm centre to centre both ways, with one handle for lifting made out of 8 mm dia MS bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 40 mm bore galvanized steel tubing medium grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown in Figure 15A of IS 3043 :1987, complete all as specified and directed.

Supply, installation and commissioning of street light control panel board of size 500 x 450 x 300mm, fabricated in a CPRI approved factory, for 3 phase, 4 wire, 415 volts, AC supply, outdoor cubicle type, dust and vermin proof, floor block mounting type suitable for outddor applications, made out of 3.15 mm thick CRCA sheet with mild steel angle iron frame and legs (of length 300mm) of section 40mm x 40mm x 4mm angle iron frame and supports, front openable (with locking arrangements_ with 100 Amps Busbar (04 Nos) fixed with insulator of suitable size and duly finished powder coated of approved colour with necessary earthwork, excavation & PCC work complete all as specified and directed and comprising of the following accessories :- (a) MCB, 10 kA, TPN, 63 Amps - 01 Nos (b) LED indicating Lamp with holder for main supply & standby supply indicating RYB (Set of three) - 01 Set (c) Analogue time switch, 3 module, 24 Hours programme, current capacity 16 Amps - 01 No (d) Contactor 32 Amps, 3 pole, 415 volts - 01 No

PINKY CO.

UNITED ENGINEERS

DEB AND COMPANY

MAZUMDER ENTERPRISE

R.K.TRADING CO. INDIA

dutta and dutta