ADDN/ALTN TO MD OFFRS ACCN AT ARJAN VIHAR, DELHI

Amount

Demolition of cement concrete (un-reinforced) in any floor n.exc 15cm thickness (below or above ground level) not otherwise specially provided including removal of rubbish out side complex (MOD land), complete all as specified & directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) by using diamond saw blade cutting machine without damaging adjacent RCC structures not otherwise including removal of rubbish outside complex ( MOD land), complete all as specified & directed.

M&L for 25 mm thick cement concrete 1:2:4 type B-0 using 12.50 mm graded crushed stone aggregate as in sub base of tiles, surface even and rough without using extra cement, complete all as specified & directed.

M&L for 75 mm thick cement concrete 1:3:6 type C2 using 20mm graded crushed stone aggregate as in plinth protection, laid to slope of 1 in 24 in alternate basis system, surfaces even and smooth without using extra cement, each bay shall not exceed 3m in length, 12mm wide joint & 75mm deep joint shall be formed between the bays which shall be filled with Mastic filling to full depth comprising a mixture of 1 part of heator hot blow bitumen 85/25 portion and two parts of heated badrapur sand (by volume), complete all as specified and directed.

M&L for Reinforced cement concrete 1:1.5:3 type A-1 using 20mm graded crushed stone aggregate (nominal mix) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like including bonding agent, complete all as specified and directed.

M&L for Form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick (horizontal or sloping) for rough finished surfaces of concrete, complete all as specified & directed.

M&L for Form work to edges of concrete flats, treads, breaks in floors window cill, concrete railing opening in conc wall , floor and roof n.exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n.exc 20cm wide for rough finished surfaces of concrete, complete all as specified & directed.

Supply & fixing TMT bars 10mm dia & over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified & directed.

All as per Srl item No. 08 above but 6mm dia & over upto & including 10mm dia in stirrups, spacers and binders.

Demolition of brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified & directed.

M&L for Brickwork with sub-class ‘B’ bricks (old size), straight or curved on plan exc. 6m in mean radius, built in cement mortar 1:6, complete all as specified & directed.

All as per Srl item No.11 before but except bricks

M&L for Brickwork with sub-class ‘B’ bricks (old size), straight or curved on plan to any radius, half brick thick walls built in cement mortar 1:4, complete all as specified & directed.

M&L for PCC 1:2:4, nominal mix, type B-1, using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, coping, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified & directed.

Taking down cement plaster of any description and in any position of brick or stone wall/concrete surfaces on walls, ceiling etc including raking out joints ,hacking for key scrubbing down with water etc & prepared to receive new plaster, complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar on fair faces of brick work or concrete surfaces , applied in two layers ie. Ist layer of 10 mm thick rendering in cement mortar 1:6 and 2nd (top) layer of 5 mm thick rendering in cement mortar 1:4 mixed with liquid WPCas per manufacturers instructions, finished even and fair, complete all as specified and directed. Note:- WPC shall be measured and paid for seperately under respective item.

M&L for 12mm thick rendering in cement mortar 1:6 on fair faces of brick surfaces or concrete surfaces, surface finished even and smooth without using extra cement, complete all as specified & directed.

Supply only integral water proofing admixture of approved quality.

M&L for Preparation of old decorated surface (Plastered or unplastered) of ceiling by brooming down or by steel wire brushes, scraping down smoke spots, moulds, moss and efflorescent salts, trading oil, greasy spots etc. and applying two coat of oil bound distemper, complete all as specified and directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on ceiling finished even and fair without using extra cement, complete all as specified and directed.

M&L for complete removal of existing treatment from old decorated plastered surfaces of ceiling and applying two coat of oil bound distemper over a coat of 1 mm waterproof wall care putty cement base, complete all as specified and directed

M&L for preparation on new plastered surfaces of ceiling with two coat of oil bound distemper over a coat of 1 mm waterproof wall care putty cement base on ceiling on plastered surfaces, preparatory to distempering, complete all as specified and directed

M&L for Complete removal of existing treatment from old decorated plastered or unplastered surfaces of walls and applying two coats of white lime washing, complete all as specified & directed.

M&L for preparation of the newly plastered surfaces of walls applying waterproof cement base wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two or more coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification, complete all as specified & directed.

M&L for preparation of old decorated surface (plastered or unplastered) of walls by complete removal of existing treatment by mechanical grinder and applying waterpoof cement base wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two or more coats distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification, complete all as specified & directed.

M&L resecuring or easing and adjusing without taking down of doors for easy opening/closing, tightening of hinges and changing its position or adjustment of tower bolts/sliding bolts etc area exc. 1sqm but not exc. 2 sqm each,complete all as specified and directed.

M&L for 2nd class hardwood plain, solid straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints, complete all as specified& directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each, complete all as specified & directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n exc 4.0 sqm each, complete all as specified & directed.

Taking down shutters of any description exc. 1 sqm and not exc. 2 Sqm each, complete all as specified & directed.

Taking down shutters of any description exc. 1 sqm and not exc. 2 Sqm each and refixing in the same opening after carrying out necessary repair, complete all as specified & directed.

Supply & fixing Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 45 x 70 mm comprising of virgin PVC polymer of K value 50-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and nontoxic additives (max toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length, complete all as specified & directed Notes: - (a) For WPC solid door/windows frames, minus 5mm tolerance in dimension i.e., depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made. (b) Contractor will provide screw out test certificate and manufacturers test certificate.

Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified & directed. Notes: (a) Stainless steel butt hinges shall be paid for separately under relevant item. (b) Contractor will provide screw out test certificate and manufacturers test certificate.

S&F double rebated, Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 65x 125 mm comprising of virgin PVC polymer of K value 50-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and non toxic additives ( max toxicityindex of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engr in charge.Note: For WPC solid door/windows frames,minus 5mm tolerance in dimension i.e depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made. Note : Contractor will provide screw out test certificate and manufacturers test certificate.

Supply and fixing Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 50x 100 mm comprising of virgin PVC polymer of K value 50-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and non toxic additives ( max toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete all as specified & directed. Notes: (a) For WPC solid door/windows frames,minus 5mm tolerance in dimension i.e depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made. (b) Contractor will provide screw out test certificate and manufacturers test certificate.

Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified & directed. Notes: (a) Stainless steel butt hinges shall be paid for separately under relevant item. (b) Contractor will provide screw out test certificate and manufacturers test certificate.

Supply and fixing 30mm thick FACTORY MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 650 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company, Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (Confirming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. SS butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through Other hardwares shouldbe fixed with 19*6mm size steel screws etc. complete all as specified & directed, manufacturer's specification & drawings. Notes: (s) Fixture/fittings shall be measured & paid under relevant item. (b) Contractor will provide screw out test certificate and manufacturers test certificate.

Supply & fixing Mild steel work as in bands, straps, supports or stays for rain water, vantilating pipes including bolts, if required, bolt hooks (stay), heavy for large gates; hook and pintle hinges; large hasp and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles, conforming to Fe-290 grade-E-165, complete all as specified & directed.

Dismantling boarding any description (board/plywood) fixed in any position with screw, complete all as specified & directed.

Supply & fixing Factory Made 18mm thick 100% Solid WPC (Wood polymer Composite) Plain Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural Fibers (Wood Powders/ rice husk/ wheat husk) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded (Inner) with density not less than 650 kg/cbm Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws, complete all as specified & directed. Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet/Kitchen & Cabinets.

Supply & fixing Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Laminated Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded (Inner) with having minimum density not less than 650 kg/cbm having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 , Modulus of elasticity 850N/mm2 and esistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixinng stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws,complete all as specified & directed. Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet/Kitchen and Cabinets.

S&F 100 mm long (size) butt hinges, medium weight, stainless steel (Grade 304), complete all as specified & directed.

S&F 75 mm long (size) butt hinges, medium weight, stainless steel (Grade 304), complete all as specified & directed.

S&F 75 mm long L Bihari concealed type hinges including stainless screw, complete all as specified & directed.

S&F in repairs 150mm size double action spring, hinge, mild steel with steel wire spring, stove enamelled black, complete all as specified & directed.

S&F 300mm long, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed, complete all as specified & directed.

S&F in repair 300mm long, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed, complete all as specified & directed.

S&F 300mm long, stainless steel of AISI 304 grade, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and fixed, complete all as specified and directed.

S&F 250mm long, stainless steel of AISI 304 grade, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and fixed, complete all as specified and directed.

S&F 150mm long stainless steel barrel tower bolt of extruded section, complete all as specified and directed.

S&F 200mm long stainless steel barrel tower bolt of extruded section, complete all as specified and directed.

S&F in repair 200mm long (size) aluminium anodised, barrel tower bolt of extruded section and fixed, complete all as specified and directed.

S&F 150mm size extruded aluminium alloy handle, fabricated type, anodised, complete all as specified and directed.

S&F 150mm size stainless steel AISI 304 grade fancy type handle complete all as specified and directed.

S&F stainless steel AISI 304 grade floor door stopper with hard drawn steel spring 140mm long, complete all as specified and directed.

S&F stainless steel hasp and staple, 100mm size, safety type, brass with stainless steel hinge pin including bolt to hinge plate & fixed with screws, complete all as specified and directed.

S&F 150x100mm concealed type SS handle for kitchen cup boards shutters, cabinets, crocery shelf drawers fixed with nuts, screw and washer of mild steel bright finished, complete all as specified and directed.

S&F ball catches with 8mm dia steel ball and brass body and striking plate including letting in and fixed, complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with steel wire staples, complete all as specified and directed.

S&F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed stainless steel wire staple, complete all as specified and directed.

S&F 4.00mm thick plain sheet glass with wooden beads, PVC beading, aluminium beads, in square n.exc 0.5 Sqm in each pane, complete all as specified & directed.

S&F 4.00mm thick figured glass, pin head type and glazing with wooden beads, glass putty, PVC beading, aluminium beads, complete all as specified & directed.

S&F 5.5mm thick sheet glass ordinary quality in square n.exc 0.5 Sqm each including grinding of edges for crockery cupboard including taking out/ broken glass with roller, complete all as specified & directed.

S&F 150mm ordinary rat tail rod, pattern door spring including roller and roller plate of mild steel and fixed to pressed steel frame / MS frame/ wooden chowkhats including necessary welding work etc where-ever required, complete all as specified & directed.

S&F in repair 150mm ordinary rat tail rod, pattern door spring including roller and roller plate of mild steel and fixed to pressed steel frame / MS frame/ wooden chowkhats including necessary welding work etc where-ever required, complete all as specified & directed.

S&F MS roller with 'C' shape staple, chromium plated for 5.5mm thick sheet glass, complete all as specified & directed.

S&F Stainless steel drapery curtain rods confirming to ASTM Schedule 5S gold or antique silver 25 mm nominal dia of SS-304 grade of approved quality with two number decorative brackets design as approved fixed in brick/concrete wall with same finished knobs/latto on each end of curtain rod including taking down old pelmet, complete all as specified and directed.

M&L for Preparation of new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified & directed.

M&L for Preparation of old painted surfaces of wood and wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint, complete all as specified & directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar, complete all as specified & directed.

M&L for coloured ceramic tiles of size 600x600x 7 to 8mm thick as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement over 15mm thick screed bed in cement mortar 1:6, complete all as specified & directed. Note: Double charged vitrified ceramic tiles light shade 10mm thick of 600x600mm shall be used in lieu of ceramic tiles on no cost basis.

M&L for Non skid ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

M&L for Glazed ceramic tiles in vertical surface 600x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering in cement mortar 1:4, complete all as specified and directed.

M&L for double charged vitrified Ceramic tiles light shade 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm of size (600mm X 1200mm), in floors etc. set and jointed with epoxy tile grout to match the colour of tiles using 3mm thick PVC spacers complete including 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

All as per Srl item No 74 above but as in skirting over and including 10mm thick rendering in cement mortar 1:4.

M&L for 16-18mm thick granite ‘Jade black’ table rubbed and polished in Step, Jambs, Pillar, Window Cill, Cooking Platform in single piece, in cooking platform additional 75mm width of same granite patti stick with araldite or equivalent adhensive full moulding of edges to match the colour of granite, fixed with 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed. Notes :- (a) Additonal 75mm width patti shall be measured separately. (b) Minimum rate of granite should not be less than Rs.150 per Sqft including GST.

M&L for 16-18mm thick Machine cut kota stone single piece stone slab for riser, treads, landings over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab laid over and including 15mm thick screed bed in cement mortar 1:6 and rounding of edges, rubbing and polishing, complete all as specified and directed.

M&L for 15mm thick Full body vitrified tiles of size 800x 2400 mm of approved shade in floor set and jointed with epoxy tile grout to match the colour of tiles using 3mm thick PVC spacers complete including 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed

M&L for 15mm thick Full body vitrified tiles in single piece of approved shade including 15mm thick screed bed in CM 1: 6 as in treads/risers of steps in one piece including cutting, jointing, or step grooveing if required and full moulding, complete all as specited and directed. Note : Step grooving shall be factory made and factory moulded.

Taking up or down 15 mm dia GI tubing and connections, complete all as specified and directed.

Taking up or down 20 mm dia GI tubing and connections, complete all as specified and directed.

Supplying and laying of CPVC 20mm OD pipes SDR 11 & plain/brass CPVC SDR 11 fittings on walls/ceiling or laying in floors, complete all as specified & directed with fitting as required.

Supplying and laying of CPVC 25 mm OD pipes SDR 11 & plain/brass CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified & directed with fitting as required.

S&F in Soft closing ball bearing telescopic channel of size 20 inch long fixed with screws in cupboards incl all fittings complete all as specified & directed. Note : Runner/ Channel should be SS 304 grade and load capacity should not be less than 45 kgs

S&F Modular Cabinet Kitchen with accessories of Stainless Steel grade-304, 6mm size rod thickness including the followings :- (i) Perforated Cutlery basket, (ii) Grain trolley, (iii) Thali basket, (iv) Cup & saucer basket, (v) Glass basket, (vi) Plate basket, (vii) Premium magic corner (viii) Oil Pull out Tray (Triple basket layer), (ix) Dust bin, (x) Cleaning kit rack of size as per site requirement all specified & directed.

S&F Galvanized iron tube as in spout pipe, medium grade, 50mm bore in short length, cut to shape required including cutting holes in walls and making good in cement mortar 1:3, complete all as specified & directed.

Dismantling of cast iron pipe of any dia (soil/waste/vent) with fittings etc fixed to walls, ceiling, on floors & from trenches if required including taking out any type of joints, complete all as specified & directed.

S&F 75mm dia (bore of pipe) cast iron (sand cast) soil, waste, vent hubless pipe as per IS-15905:2011 in any length with or without ears with jointed with stainless steel shielded SS-304 coupling double screw system with EPDM rubber, fixed to walls, complete all as specified & directed.

S&F 100mm dia (bore of pipe) cast iron (sand cast) soil, waste, vent hubless pipe as per IS-15905:2011 in any length with or without ears with jointed with stainless steel shielded SS-304 coupling double screw system with EPDM rubber, fixed to walls, complete all as specified & directed.

S&F 100mm dia (bore of pipe) cast iron hubless bends as per IS-15905:2011 (any radius), diminishing pieces or tapers (larger bore measured) jointed with stainless steel shielded SS-304 coupling double screw system with EPDM rubber, complete all as specified & directed.

S&F 75mm dia (bore of pipe) cast iron hubless bends as per IS-15905:2011 (any radius), diminishing pieces or tapers (larger bore measured) jointed with stainless steel shielded SS-304 coupling double screw system with EPDM rubber, complete all as specified & directed.

S&F 100mm dia (bore of pipe) cast iron hubless Tee as per IS-15905:2011 (any radius), diminishing pieces or tapers (larger bore measured) jointed with stainless steel shielded SS-304 coupling double screw system with EPDM rubber, complete all as specified & directed.

S&F 75mm dia (bore of pipe) cast iron hubless Tee as per IS-15905:2011 (any radius), diminishing pieces or tapers (larger bore measured) jointed with stainless steel shielded SS-304 coupling double screw system with EPDM rubber, complete all as specified & directed.

All as per Srl item No.92 above but fitted with hubless oval access door as per IS-15905:2011 for 100mm dia (bore of pipe).

All as per Srl item No.93 but fitted with hubless oval access door as per IS-15905:2011 for 75mm dia (bore of pipe).

S&F 75mm dia (bore of pipe) hubless cast iron as per IS-15905:2011 branch pieces single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, fitted with oval access door jointed with stainless steel shielded SS-304 coupling double screw system with EPDM rubber, complete all as specified & directed.

S&F 100mm dia (bore of pipe) hubless cast iron as per IS-15905:2011 branch pieces single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, fitted with oval access door jointed with stainless steel shielded SS-304 coupling double screw system with EPDM rubber, complete all as specified & directed.

S&F in repair cast iron floor trap square type with Cockroch Proofing CP grating with or without hole including provision of jointing to waste pipes in run lead joint dia of outlet 75mm, complete all as specified and directed.

S&F in repairs 75mm dia of outlet cast iron floor trap fixed with stainless steel shielded (SS-304) coupling double screw system with EPDM rubber to waste pipe fixed in cement concrete 1:2:4 type B1, complete all as specified and directed..

S&F in repairs vitreous china wash down water closet, pedestal pattern with ‘S’ trap fixed in position with necessary cement work, complete all as specified and directed. Makes : Jaquar CAT Part No.CNS-WHT-551SSPP, Hindware CAT Part No.20079, Cera CAT Part No.S1053104S

S&F in repairs PVC valve less symphonic action type flushing cistern low level 10 ltr capacity (ISI marked) white with inlet ball valve float and handle including brackets, complete all as specified and directed”. Makes : Jaquar CAT Part No. WHT-184 ANL, Hindware CAT Part No. 516366, Cera CAT Part No. B1020106

BLANK

S&F mortice lock of size 100mm with Brass fancy type and vertical type 4 levers with key in triplicate, complete all as specified and directed.

S&F sinks made of stainless steel 1mm thick kitchen with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm all as specified and directed.

S&F in repairs Brass CP health faucet hand shower type with 8mm dia 1.2 Meter long Flexible Tube and Wall Hook screwed for iron pipe fancy type long body, complete all as specified and directed. Make. Jaquar CAT Part No. ALD 573, Cera CAT Part No.F8030107AB, Hindware CAT Part No. F160023, Kohler CAT Part No. K-98100IN-CP

S&F in repair PVC connection pipe of 15mm x 600mm long with 2 Nos brass check nuts with washers, complete all as specified and directed.

S&F in repairs CP connection pipe of 15mm x 600mm long with 2 Nos brass check nuts with washers, complete all as specified and directed.

S&F in repairs vitreous chinaware coloured wall hung wash hand basin with full pedestal of size 550mm x 400mm complete including CP brass waste coupling, waste pipe ,complete fixing arrangement and cutting for and pinning in walls & making good, complete all as specifed and directed.

S&F in repairs vitreous china squatting pan of orissa pattern long pan size 580 x 440 mm white with 'p' or 'S' trap front or back inlet and integral foot rest any pattern (excluding flushing cistern and flush pipe) including provn of lime concrete bedding, complete all as specified & directed.

S&F in repairs PVC valveless, syphonic action type flushing cistern, 10 litres capacity, plunger type, low level, white with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long, complete all as specified & directed.

S&F Toilet paper holder with flap, brass chromium plated, complete all as specified & directed . Make.Cera CAT Part No: F5004110, Jaquar CAT Part No.CPA-CHR-1153, Hindware CAT Part No.F-880003CP, Kohler CAT Part No K-5633IN-CP

S&F in repairs fancy type brass chromium plated soap dish, complete all as specified & directed . Make.Jaquar CAT Part No: ACN-CHR-1131N, Cera CAT Part No: F5007106, Hindware CAT Part No. 880011GRT

S&F in repairs stainless steel cockroach trap with jali 125mm dia, complete all as specified and directed.

S&F in repairs stainless steel peg set of 6 peg, 45 centimeter long, complete all as specified and directed.

S&F in repairs fancy type 15mm dia brass chromium plated quarter turn basin mixer with braided hose for mixing hot and cold water screwed down for iron pipe and fixed to WHB complete all as specified and directed. Make. Jaquar CAT Part No: FLR-CHR-5167NB, Cera CAT Part No: F-2008461, Hindware CAT Part No. F570014, Kohler CAT Part No. K-29928IN-4ND-CP

S&F in repairs 15mm dia chromium plated quarter turn wall mixer hot & cold L bend 3 in 1 pattern fixing and connection to pipes, complete all as specified and directed. Make. Jaquar CAT Part No: FLR5281N, Cera CAT Part No: F-2002403, Hindware CAT Part No. F-570022, Kohler CAT Part No K-98754IN-4-CP

S&F in repairs fancy type 15mm dia brass chromium plated quarter turn fancy type wall mixer hot & cold with long swan for kitchen sink fixing and connection to pipes complete all as specified & directed. Make.Jaquar CAT Part No: FLR5309N, Cera CAT Part No: F1003501, Hindware CAT Part No. F570027, Kohler CAT Part No. K-99483IN-A4-CP

S&F in repairs fancy type chromium plated quarter turn brass angle valve type suitable for 15mm bore pipe complete all as specified and directed. Make.Jaquar CAT Part No: FLR5053N, Cera CAT Part No: F1001201, Hindware CAT Part No. F-340006CP, Kohler CAT Part No. K-80158IN-9AV-CP

S&F in repairs fancy type 150mm dia brass CP shower rose including shower arm 600mm long, complete all as specified & directed. Make. Cera CAT Part No. F-7010609AB & F-7040207, Jaquar CAT Part No. OHS-CHR-1663 & SHA-CHR-479L600, Hindware CAT Part No. F-160219CP & F-160024CP, Kohler CAT Part No. K-23657IN-CP & K-16346-IN-CP

S&F in repairs fancy type sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with CP brackrt gaurd and railling 60 cm long, complete all as specified and directed.

S&F in repairs fancy type glass corner 300mm radius of 10mm thick toughned glass with CP railing fixed with screws, complete all as specified and directed.

S&F in repairs fancy type glass corner 250mm radius of 10mm thick toughned glass with CP railing fixed with screws, complete all as specified and directed.

S&F in repairs fancy type stainless steel towel rack size 600mm X 300mm including apair of brass bracket, complete all as specified and directed. Make. Cera CAT Part No F-5003101, Jaquar CAT Part No.CPA-CHR-1181FH, Hindware CAT Part No.F-580008CP, Kohler CAT Part No.K-17529T-CP

S&F Stainless steel of AE - SI 316 grade tubular towel ring including apair of CP brass bracket, complete all as specified and directed.

S&F in repairs bib tap with crutch or butterfly handle, quarter turn screwed down, screwed for iron pipe, 15mm dia, fancy type, cast copper alloy, chromium plated long body with flange complete all as specified and directed. Make. Jaquar CAT Part No: FLRCHR-5047N, Cera CAT Part No : F-2008152, Hindware CAT Part No. F460003 & Kohler CAT Part No K-16093IN-4-CP

S&F in repairs Brass CP bib tap fancy type with flange 15mm dia screwed for iron pipe or for brass ferrule (Minimum weight 15mm-200gms), complete all as specified and directed.

S&F in repairs stainless steel sink with drainage board made out of 1.00mm thick sheet for kitchen with plug, washers, waste pipe including connecting union overall size 910 mm x 460 mm with bowl size 410mm x 330mm x 160 mm including taking out existing sink with waste fittings, complete all as specified and directed.

S&F in repairs Stainless Steel plate rack of size 90x80x25cm made with 1.00 mm thick sheet including taking out existing wooden plat rack, complete all as specified and directed.

S&F 1000 ltr capacity rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top) hoisted and fixed in position including supply & fixing 20mm Ball brass valves, high pressure with polythene float and flynut complete, screwed for iron pipe or brass ferrule Minimum wt 20mm-210grm, 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed and dismantling of PVC water tanks of exc 500 litres and n.exc 1000 litres capacity of any condition or type, complete all as specified and directed.

S&F in repairs of 25mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified & directed.

S&F for steel windows fabricated from roll formed sections made of galvanized steel colour coated powder coated (Base steel as per Sqm IS-513 D quality galvanized as IS 277 with zinc coating of 120 GSM with total coated thickness of 0.60mm. The coated section shall be with primer coated of primer of -7 microns thick, finish painted with a polyster paint of 12.16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure plyster powder upto 50-60microns thick with the following specifications (a) Main frame 72mm x 55mmx0.58mm (b) Mullion 72mmx50mm x0.58mm(c) Glazed/guazed shutter frame 47mmx20.20mmx0.58mm (d) Glass beads size 12mmx12mmx0.58mm Accessories. Each shutter shall be provided the following fittins (a) Stainless steel pipe of hinges 01 set (b) Alumminium powder coated handle-04 Nos. Glass panes Glazed shutter and fixed glass provided with glass of 5.00mm thick float glass. WIRE MESH -Stainless steel wire mesh of 0.3 mm nominal dia of wire and average width of aperature 1.40mm. Grills window shall be provided with grill made of 10mm square MS bars welded to 12mmx6mm thick MS plate. Distance between bars should not be more than 12cm c/c. Total grill unit shall be enamel painted and fixed to window frame with screw. Note: The glazed/Guaged shutter includingguard bars shall be measure once i.e. as per area of opening. No separate payment of separate shutter i.e. glazed and fly proof and guard bars shall be made. Area of shutter shall be the area of opening. The rate quoted by the contractor is deemed to inclusive of all aspects as specified in Drg No- CEDZ/TD/289 sheet 1 R/2 and 2R/2.

(a) Dismantling of floor size not exceeding 4.00 Sqm mtr for EWC water closet and removing out the cinder/concrete from sunken protion, cleaning of RCC surface to remove dust, loose particle with compressed air or any other suitable method depending on site conditons, grinding any sharp edges etc all as specified and directed. (b) Cleaning or RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc. (c) M&L for a glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top & Seal-107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika® Fab-I and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or Pidilite. (d) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with Sika ® Plastocrete plus as specified. (e) M&L for providing 25mm dia GI medium grade pipe spout projecting at least 150mm beyond outer face of wall. (f) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed. (g) The area of Each WC portion is n.exc 4.00 Sqm each. (h) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account. Note : The work will be executed by authorised manufacturers/applicator only.

(a) Dismantling of floor size not exc 1.50 Sqmtr for IWC Water closet and removing out the cinder/concrete from sunken protion, cleaning of RCC surface to remove dust, loose particle with compressed air or any other suitable method depending on site conditons, grinding any sharp edges etc all as specified and directed. (b) Cleaning or RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc. (c) M&L for a glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top & Seal-107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika® Fab-I and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or Pidilite. (d) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with Sika ® Plastocrete plus as specified. (e) M&L for providing 25mm dia GI medium grade pipe spout projecting at least 150mm beyond outer face of wall. (f) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed. (g) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account. Note : The work will be executed by authorised manufacturers/applicator only.

M&L for 16 to 18mm thick granite stone of size 3' x 2' fixed on wall over 15mm thick screed bed in cement mortar 1:4 and ingraved flat Nos and border over the stone for building insignia (letter size 3" to 2"), complete all as specified and directed.

M&L for 5mm thick acrylic sheet of size 200mm x 300mm fixed on wall over suitable fastener border over the stone for building insignia (letter size ht 100mm and 50 mm width) for numbering Qtrs, complete all as specified and directed.

Cutting shrubs, wild growth, plants not exc 30 cm girth grown on permanent structures and removing same from roots and stopping the recurrence by injecting herbicide Glyphosphate 4+ solution (04 % concentrate) into plant root to eliminate further growth. Application shall be as per manufacturer intructions. The disturbed area shall be repaired with PCC (1:2:4) Type B0 mix and surface finished even and smooth in cement mortar 1:4 including applying two coats of matching finish of adjacent area. Minimum plant in each block is 10 Numbers.

Dismantling of brick tiles or terracing tiles single layer on roof and removing the rubbish outside complex (MOD land),including removal of vagitation if any complete all as specified and directed

Demolition of mud in roof, any thickness, including mud plastering and mud phuska under brick tiles at any situation and height, complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc, complete all as specified and directed.

M&L for Brushing neat cement slurry with 3 Kg of cement per square metre, complete all as specified and directed .

M&L for cement concrete 1:2:4 type B1 using 12.5mm graded crushed stone aggregate on roof padding surface finished even and smooth without using extra cement ,complete all as spd & directed.

M&L for rendering 10mm thick on top of roof concrete in cement mortar 1:4 with liquid water proofing compound as per manufacturers instructions to have a smooth surface for laying of water proofing membrane, complete all as specified & directed. Note: Liquid water proofing compound will be measured and paid seprately under respective item.

M&L for APP based polymeric membrane sand/rough finish minimum weighting 3 kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150 gms/sqm) over one coat of 85/25 bitumen @1.2 kg/sqm and paste the membrane with torching method and again apply a coat of 85/25 bitumen @ 1.2 kg/sqm at overlapping joints, complete all as specified & directed.

S&F for Heat Resistant Terrace Tiles (300 mm x 300 mm x 10 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and set and jointed with epoxy tile grout to match the colour of tiles using 3mm thick PVC spacers complete including providing skirting along the parapet walls of height as directed in the same manner including 15 mm thick backing coat in cement mortar 1:4, complete all as specified & directed.

M&L Cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate as in roof kerbs or mud stops etc including weathering slightly rounded or chamfered edges, finished even and smooth without using extra cement, complete all as specified & directed

M&L for Providing & injecting chemical for post construction ATT along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in a portion with cement mortar 1:2 to match the existing apron complete all as specified and directed.

M&L for post construction anti termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same, complete all as specified and directed.

M&L for post construction anti termite treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor, complete all as specified and directed.

M&L for followings :- (i) Removing plaster & finishes all around the coloumns, slabs & beams (on all four sidescription of column to full height , three sidescription of beam to entire span & bottom of slab to area as directed) (ii) After cleaning gently removing cover concrete using pneumatic/electric chipper or any other approved tool in entire portion of structural member (removal of cover concrete shall be done to an extent when reinforcement is visible) (iii) Removal of cover concrete with under cutting of up to a depth of 20mm beyond reinforcement around full circumference & full length of bar where directed. (concrete shall be stripped to an extent concrete substrate is exposed) (iv) Cleaning exposed concrete substrate by using water jet. (v) Removing visible rust along the length of reinforcement using hand tools as approved. Supply & applying of rust removing chemical to remove rust from existing reinforcements. (The Engr-in-charge may order sand blasting if rust is visible) (vi) Any other work as directed by Engr-in-charge to present clean surface for determination of type of repair to be carried out complete all as specified and directed.

M&L for providing rust proof /anti corrosive treatment to bars :- (i) cleaning of all exposed bars (new & old) alround (ii) Apply a single coat of Alkaline rust converting primer on alround bars new & old as recommended by the manufactuer (iii) Apply two coats of Epoxy phenolic anti corrosive protective coat on bars alround new & old as recommended by the manufactuer. Note : Anti corrosive treatment shall be continuous espcially in the regions where pitting, imperfections, etc were present on the surface of the bars. It is important that the rear portions of re bars (those towards the concrete substrate) should not be left without coating.

M&L for providing PMM (Polymer modified cementitious mortar) :- (i) Dry sub strate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness. Note : Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for parapet railing, balconies, metre rooms shaft area any description complete as specified and directed upto six storey height..

S&F MS Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0

M&L for Preparation of new steel and iron surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified.

M&L for Preparation of old painted surfaces of steel and iron surfaces of any description over 10 cm width or girth not otherwise described and applying two coat of synthetic enamel paint, complete all as specified.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 for hand grip in balcony railing and roof terrace or grills, complete all as specified and as directed.

S&F Stainless steel 304 grade modular railing system comprising Ø 50 mm dia S.S Handrail fixed on Ø 50 mm dia ss round baluster with all necessary Accessories, Ø 25 mm Grade two no’s Horizontal Members, Ø 16 mm S.S Verticle Members and all necessary fixtures. The balustrade would be fixed on to the floor with with Ø100 x 8mm Thick 304 Grade base Plate with 4 No. M10*100mm anchor fasteners. Base plate shall be concealed with suitable ss 304 grade cover cap so that the mounting anchor fastener are not visible after installation. Wall thickness of handrail, balusters, vertical members and horizontal members/mid rail shall be 2mm along with all with all visible components Developed in high grade ss & whenever required joints to be filled with modular bend. Railing height to be taken @ 1100mm from finish floor level, complete all as specified and directed.

M&L for chipping of spalled and loose concrete and cleaning rust from re-inforcement by sand brushing scrubing down concrete surfaces with wire brushes cleaning with water allowed to dry applying a layer of zinc rich epoxy primer as antirust on all exposed reinforcement followed by a layer of bonding coat of a layer of epoxy adehessive on complete exposed surfaces of concrete and provide guniting in two layers over steel welded mesh 2 mm dia of wire and total aperture 75 mm, thickness of gunite n.exc 25 mm thick (average thickness) using cement mortar 1 :3 with OPC 43 grade cement mixed with polycrete admixture @ 2 % by wight of cement or as per manufactures instructions and finally applying 10 to 15 mm thick cement plaster over gunite surfaces of required thickness to give an even uniform and smooth finish conforming to proper Geometrics in cement mortar 1:4 to match with the existing surface as in side and soffits of slabs,chajjas,fins,facias ,parapets ,columns and beams etc complete including necessary scaffolding ,shuttering necessary chased to brick work or RCC members at any height upto six storey buildings incl removing of small trees shrubs etc all as specified Note: steel welded mesh to be welded with the existing reinforcement. The cost of welded mesh is to be welded with the existing re-inforcement is deemed to be included in the quoted rate complete all as specified and directed.

Taking down existing steel rolling shutter incl hood cover pull & push type not exc 12 Sqm area of clear opening and cleaning the sides of shutters suspensions shafts,anti-guide channels and greasing all the moving parts of rolling shutters and straightening rolling shafts and replacement of bolts and nuts as required for smooth functioning of shutters and refixing the same incl hood cover complete all as specified and as directed.

S&F in repairs mild steel lock plate & handles made of of Flat iron 35 x 5 mm incl welding and painting with two coats of synthetic enamel paint over one coat of red oxide primer, complete all as specified and directed.

S&F in repairs mild steel helical wire springs (confirming) as to IS-6248-1970) for shutters not exc 9 Sqm of approved make complete all as specified.

S F in repairs roller ball bearing (ISI marked) for 32/40 mm dia pipe shaft complete all as specified and as directed.

S&F in repairs if interlocking lath section formed from rolled MS strip 1,2mm thick for rolling shutters above 3.5m width, complete all as specified and directed.

S & F in repair of steel rolling shutters without ball bearing, as specified incl top cover anchoring rod hasp & staple and one shop coat of primer before erected in position as directed complete manual type thickness of lath 1.25mm. complete all as specified and directed.

S&F Prefabricated Factory made FRP Chajja 4mm thick 600mm wide of Fibre ways brand or equivalent in required size, colour and design made by Resin Transfer Moulding (RTM) machine Technology, resulting in void free compact laminate in single piece, having smooth gradual slope curvature of easy drainage of water and duly reinforced by 2nos vertically and 1 nos horizontally 50 x2 mm thick MS flat with 12mm in built hole for grouting on existing wall along with the 50mm flanges duly inserted and sealed in the wall complete in one single piece casted monolithically including all necessary fittings, complete all as specified and directed.

Cutting holes in brick wall built in cement mortar for inserting hold fasts, depth of embedded postion of hold fast /lugs measured from the face the jambs into the wall exc half brick but n.exc one brick thick and making good the dismantaled portion in cement mortar 1:3 or in cement concrete 1:2:4 type B-1, using 20mm graded stone agg complete all as specified upto six storey height, complete all as specified and directed.

S & F 500 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position incl Dismantling of PVC water tanks of exc 250 litres and n.exc 500 litres capacity of any condition or type complete all as specified and directed.

S&F 20 mm Ball brass valves,high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed. Minimum wt 15 mm -142grm , 20mm-210grm ,25mm -455grm,40mm-690grm complete all as specified and directed.

S&F of 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed complete to walls, ceilings or in floors with suitable clamps/bracket to maintain the gap between wall & pipe and fixing properly including taking down old PVC/CI pipes and necessary cutting through RCC roof and brick work etc (above six storey height) and making good, complete all as specified and directed.

S&F of 110 mm dia PVC (SWR) bends any radius with solvent joints, complete all as specified and directed.

S&F powder coated aluminium Door seal not less than 1.00 mtr long with fine fibres suitable for fixing in doors, complete all as specified and directed.

Removing building materials etc.to a distance of 5.00km beyond the land included in the rates, including loading, unloading and stacking at the destination, complete all as specified and directed.

S&F 50mm dia wooden magnetic door stopper catcher fixed with screw in rear side of door to arrest closing, complete all as specified and directed.

M&L for providing precast reinforced cement concrete jallies 45 mm thick including all mouldings type B-0 1:2:4 using 12.5mm graded crushed stone aggreagte set in cement mortar 1:4, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and providing and applying waterproof cement base putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified as directed.

M&L for preparation of old decorated plastered surfaces of walls, complete removal of existing treatment by rubbing , brooming down, washing with water etc and providing and applying waterproof cement base putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm), complete all as specified as directed.

S&F factory made uPVC any colour fixed glazed window/ventilator made of ( small series) frame 47 x 50mm mullion 47 x 68mm both having wall thickness of 1.9 + 0.20mm and single glazing bead of appropriate dimension ( Area upto 0.75 sqmtr) comprising of uPVC multichambered frame and mullion (wherevr required) extruded profile duly reinforced with 1.60 +0.20mm thick galvanised mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropraiate dimension, EPDM gasket, G.I. fasteners 100 x 8mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless screw etc.Profile of frame shall be miterd cut and fusion welded at all corners, mullion (if reqd) shall be also fusion welded including 5mm thick toughened glass drilling holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of reqd size and approval quality, all complete as per approved drg and direction of Engr in charge. Note: For uPVC frame, sash and mullion extruded profiles ,minus 5% tolerance in dimension i.e depth and width of profile dimension in higher side shall be acceptable but no extra payment on this account shall be made, complete all as specified as directed.

S&F factory made uPVC any colour three track three panels sliding window with flyproof S.S. wiremesh ( Two nos. glazed & one no. wiremesh panels ) upto 1.50m ht made of big series frame 116 x 45mm & sash 46 x 62mm both having wall thickness of 2.3 + 0.20mm and single glazing bead/ double glazing beading of appropriate dimension ( Area of window upto 1.50 sqmtr) comprising of uPVC multichambered frame and mullion (wherevr required) extruded profile duly reinforced with 1.60 +0.20mm thick galvanised mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropraiate dimension, EPDM gasket, G.I. fasteners 100 x 8mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless screw etc.Profile of frame & sash shall be miterd cut and fusion welded at all corners, mullion (if reqd) shall be also fusion welded including 5mm thick toughened glass and SS wire mesh fixed and drilling holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of reqd size and approval quality, all complete as per approved drg and direction of Engr in charge. Note: For uPVC frame, sash and mullion extruded profiles ,minus 5% tolerance in dimension i.e depth and width of profile dimension in higher side shall be acceptable but no extra payment on this account shall be made, complete all as specified as directed.

Supply and fixing factory made uPVC white colour Two track two panels sliding glazed door made of (big series) frame 67 x 50 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of door above 2.00 sqm upto 5.00 sqm) comprising of uPVC multi-chambered frame, with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC, extruded glazing beads, uPVC extruded interlock and uPVC extruded line sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, including filling of UPVC coloured panell complete all as specified and directed by Engineer-in-Charge. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made, complete all as specified as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based profile steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall (above six storey height), fixed with self tapping screws, complete all as specified & directed.

S&F of 32 mm dia PVC (SWR) pipes for Window AC drain outlet pipe with single socketed in any length with rubber ring joints fixed complete to walls, ceilings or in floors with suitable elbow, Tee, socket, clamps/bracket etc (above six storey height) and making good, complete all as specified & directed.

M&L cutting and chases pinning in concrete block/ Brick work making good to facings where required and pointing in cement morter 1:3 and cutting chases for concealed water tubing or conduit wiring,etc and making good cutting not exc 10 cm girth, complete all as specified & directed.

S&F for 75 mm dia (bore of pipe) cast iron vent cowls, complete all as specified & directed.

S&F for 100 mm dia (bore of pipe) cast iron vent cowls, complete all as specified & directed.

S&F in repairs PVC moulding to MS flat railing thickness not less than 5mm and width upto 100mm, complete all as specified & directed.

S&F of 150 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed complete to walls, ceilings or in floors with suitable clamps/bracket to maintain the gap between wall & pipe and fixing properly including taking down old PVC/CI pipes and necessary cutting through RCC roof and brick work etc (above six storey height) and making good, complete all as specified & directed..

S&F of 150mm dia PVC (SWR) bends any radius with solvent joints, complete all as specified & directed.

S&F of 150mm dia PVC (SWR) TEE any radius with solvent joints, complete all as specified & directed.

Cleaning and drying the brick surfaces/chajja and make it dust free. Prewetting the surface with water before application of Dampblock 2k, and then applying a skim coat of polymerised putty and after drying 2 coats of Smartcare dumpblock 2K @1.5 Kg/ Sqm. (Application of plaster shall be measured and paid in appropriate item), complete all as specified & directed.

Supply and installation of the PCP expansion joint system specifically designed for floor locations. The system will comprise extruded aluminum base members including self- aligning and self-centering arrangements, along with support plates, conforming to ASTM 6063 standards. The aluminum covers will feature a robust design that is both hard-wearing and maintenance-free, ensuring longevity and durability. The surface of the expansion joint covers will be serrated to provide skid resistance, enhancing safety in pedestrian areas. The design of the expansion joint cover system will minimize exposed surface areas to prevent dirt accumulation and facilitate easy maintenance. The expansion joint covers will incorporate an articulated telescope design, allowing for the accommodation of movements in all six directions (lateral, longitudinal, and vertical).This feature ensures the system can effectively handle the dynamic forces encountered in floor expansions and contractions. The system components will be made from 6063 T5/T6 aluminum alloy, supplied in a mill finish, providing the necessary strength and corrosion resistance for standard pedestrian loads. A moisture barrier membrane will be incorporated within the joint system to ensure a watertight seal, a mandatory requirement as per the manufacturer's design and as approved by the Engineer-In-Charge. All materials and installations will be adhere strictly to the manufacturer’s specification and will be installed as per direction of Engineer-in-Charge to meet specific requirement of the work. Contractor will provided manufacturers test certificate.

Supply and installation of AW expansion joint system for wall joints, both internal and external and under the direction of the Engineer-In-Charge. The expansion joints will consist of extruded aluminum base members, incorporating a self-aligning and self-centering arrangement with support plates, in compliance with ASTM B221-02 standards. The system is designed for vertical wall-to-wall and wall-to-corner applications, suitable for both new and existing construction in office buildings and complexes. The system will ensure stability with no tendency for slippage among its components, providing a secure and reliable expansion joint solution. The joint system will utilize lightweight aluminum profiles with minimal exposed surfaces, featuring a mechanically snap-locking multicellular design that facilitates movement while maintaining integrity. A moisture barrier membrane will be incorporated into the joint system to ensure a watertight seal, which is a mandatory requirement. All materials used in the system will conform to ASTM 6063 standards and will be installed as per the direction of the Engineer-In-Charge to meet the specific requirements of the work. Contractor will provided manufacturers test certificate.

M&L Packing and transportation of luggage (approx 6 tonne) within 10 km radius to include :- (a) Removal from old location and fixing such as AC (01), TV (01), Washing machine (01), RO (01), Dish Antena (01) Dish washer (01) at new location transportation. (b) Transportation of 2 wheeler and four wheelers not included. Note: Luggage will be shifted by packers and movers.

Surface dressing averaging 15 cm deep and getting out in soft/loose soil, complete all as specified and directed by Enginer-in-Charge.

M&L 75mm thick, cement concrete 1:4:8 type D- 2 using 40mm graded crushed stone aggregate as in sub base, hard standing etc, complete all as specified & directed.

M&L for Sand filling (sand cushioning) under floors or in foundations including watering and consolidations, complete all as specified and directed.

M&L for Chequered cement concrete tiles, machine pressed, factory made of size 20cmx20cm, 25mm thick, with grey cement and no pigment, set, jointed and pointed in neat cement slurry, laid in floors, complete all as specified & directed.

S&F Machine pressed precast concrete rubber moulded interlocking coloured paver block of approved pattern shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, complete all as specified & directed.

M&L for cement concrete type 1:2:4 type B1 using 20mm graded crushed stone aggregate as in as in roof kerbs or mud stops etc including weathering slightly rounded or chamfered edges, finished even and smooth without using extra cement, complete all as specified & directed

Removing excavated materials to a distance exc 1.50 Km but not exc 5 Km outside defence land and depositing where directed, complete all as specified & directed.

M&L Hardcore of broken stone or boulders guage n.exc 63mm deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface

Excavation in trenches n exc 1.5m wide and n exc 1.50m in depth for foundation etc and getting out in soft/loose soil, complete all as specified & directed.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25cm, complete all as specifed & directed.

Removing excavated material to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point, complete all as specified & directed.

M&L for PCC 1:4:8 type D2 using 40mm graded crushed stone aggregates as in foundation of manholes, posts etc, complete all as specified and directed.

M&L for PCC 1:2:4, nominal mix, type B-2, using 40mm graded crushed stone aggregate as in surface channel and drains including necessary form work, complete all as specified & directed.

M&L for Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stoped ends etc, complete all as specified and directed.

S&F DWCPE (SN8) 150mm dia (Internal Dia) pipes, snap fit coupler and rubber ring including testing and laid and properly jointed laid in trenches to a level on concrete bed, complete all as specified and directed.

M&L for precast factory made manhole cover, area of each cover n.exc 0.60 Sqm, 100mm thick with SFRC concreting including grove and hook arrangement for lifting and placing in position and sides covered by MS sheet, complete all as specified and directed.

M&L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching, internal dia of pipe 100mm, complete all as specified & directed.

M&L for 15mm thick rendering in cement mortar 1:4 on fair faces of brick surfaces or concrete, finished surfaces even and smooth without using extra cement, complete all as specified and directed.

Demolition and breaking up drain pipes (glazed stone ware, AC or reinforced concrete),150 mm dia pipe of any description and in any position set and jointed in cement mortar, complete all as specified and directed.

M&L for Brickwork with sub-class ‘B’ bricks (old size), straight or curved on plan exc. 6m in mean radius, built in cement mortar 1:4, complete all as specified & directed.

S&F Factory made 18mm thick 100% Solid WPC (Wood polymer Composite) JALI of required size comprising of virgin PVC resin of K Value 58-60 (Suspension Grade), Calcium Carbonate and natural fibers (Wood Powders/ rice husk/ wheat husk) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded (Inner) with having minimum density not less than 650 kg/cbm having good screw holding capacity ( Screw Withdrawal strength of 2000 N (Face) & 1100 N ( Edge), Minimum Compissive of 50 N/mm2 , Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free. Water/ Moisture Proof and Fire Retardant. WPC Jali to be fixed with stainless Steel butt hinges ( if required ) of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company: For Interiors / Kitchen shutters / Balcony & Internal Doors and Partitions. Note :- Contractor will provide manufacturers test certificate.

Supply and installation of joint system for various roof locations, as per the approved drawings and under the direction of the Engineer-In-Charge. The expansion joints will be constructed from extruded aluminum base members, designed to meet ASTM B221-02 standards. The system will include a self-aligning and self-centering arrangement with support plates to ensure proper alignment and stability. The expansion joint system will provide a watertight cover for roof-to-roof and roof-to-corner joints, capable of accommodating multidirectional seismic movements without placing stress on its components. The system will feature a metal profile with a universal aluminum base member, designed to adapt to various project conditions and roof treatments. The cover plate will be engineered with the appropriate width and thickness to meet the movement and loading requirements. It will be secured to the base members using the manufacturer's pre-engineered self-centering arrangement, allowing for free rotation and movement in all directions. The self-centering arrangement will include circular sphere ends that lock and slide within the corresponding aluminum extrusion cavity, enabling movement and flexure in all directions, including vertical displacement. The joint system will be designed to resist damage or deterioration from environmental factors such as falling ice, UV exposure, airborne contaminants, and occasional foot traffic from maintenance personnel. A moisture barrier membrane will be an integral part of the joint system to ensure a watertight seal, as per the mandatory requirements. All materials and installation methods will comply with ASTM 6063 standards and will be subject to the approval of the Engineer-In-Charge to ensure full compliance with project specifications.

M&L for stainless steel (grade 304) grill made of tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete including fixing the grill with necessary accessories & stainless steel dash fasteners, stainless steel bolt etc., of required size, on the top of floor or the side of waist slab with suitable arrangements, complete all as specified and directed.

Description of Work / Item(s)

Amount

Taking down carefully copper/aluminium point wiring (light/fan/ socket/power) complete from the wall by cutting/ chasing including fittings and fixtures such as switches, ceiling roses, pendants holder, regulators,sockets,light fittings etc for credit and making good the disturbed surfaces of wall, floor etc, complete all as specified and directed.

Taking down carefully sub main wiring of any description, complete all as specified and directed.

Disconnecting electric & water supply connections, nuts-bolts & taking down Geyser different capacity and shifting to MES store yard, complete all as specified and directed.

Disconnecting elect connection and taking down of ceiling fan/Exhaust fan of any make and any height, dismantling blade and removing fan alongwith blade for depositing in MES store yard, complete all as specified and directed.

Taking down defective switch fuse main board /MCCB Enclosure/ distribution iron clad or sheet metal enclosure/ MCB DBs with MCBs of any capacity and make including wooden board etc complete all as specified and directed.

M&L for Point wiring (concealed) complete with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor drawn through in and including non metallic medium grade rigid PVC conduit, ISI marked not less than 20 mm dia including all accessories concealed in wall by cutting chases and including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuty conductor including fabricated branded modular metal flush box duly make embossed, concealed in walls and making the adjacent surfaces smooth through POP work & painting as per site requirement and with suitable modular inner and outer plate for housing switches , socket out let and fan regulators etc, complete all as specified and as directed for the followings:-

(a) One light /Ceiling fan/exhaust fan point controlled by one, one way switch .

(b) One bell point controlled by one bell push.

(c) One light point controlled by two Nos two way switches

(d) One 3 pin 5 Amps socket outlet point controlled by one No one way switch on independent board.

(e) One 3 pin 5 Amps socket outlet point controlled by one No one way switch on same board

All as per item No.6 herein before but with 4 Sqmm cable for one 3 pin 15 Amp switch socket outlet and using 4 sqmm PVC single core copper conductor cable multistranded as earth wire complete all as specified and directed. Note for Item 6 & 7 : (i) In case the wiring is encountered with any beam/column, then the wiring will run on PVC casing & caping/ Existing conduit to avoid any damage to the RCC portion. (ii) No cutting shall be done in the roof for laying PVC conduit for ceiling fan point wiring, in this specified portion wires shall run through the surface new conduit shall be provided as mentioned in note (i) above. (iii) Proper colour code will be used for wiring as per the electrical rule and as directed by EIC.

S&F switch Modular type 6 Amps 230V AC, complete all as specified and directed.

S&F switch modular type 6 amp SP two way, complete all as specified and directed.

S&F Modular socket outlet 5 pin 6 Amp socket 2 module, complete all as specified and directed.

S&F switch bell push Modular type 6 Amps 1W-1 module, 230V AC complete all as specified and directed.

S&F switch Modular type 16 Amps 230V AC complete all as specified and directed.

S&F Modular socket outlet 5 pin 6/16 Amp universal socket 2 module complete all as specified and directed.

S&F ceiling rose, PVC / Polycarbonate, isolated body with three terminals, complete all as specified and directed.

S&F bell electric (ding dong) 230 volt, SP, complete all as specified and directed.

S&F of modular AC Box consisting of 20 Amp multipower socket including MCB of capacity 25 Amp mini MCB, ‘C’ curve, single phase 240 V, AC including modular box, frame, cover plate including plug top with indicator complete all as specified and directed.

S&F of LED batten luminaire surface mounted, 4 feet system wattage of 20 Watts with lifetime of 50000 burning hours with 70% of its initial lumen maintained. CRI>80, Power Factor > 0.95, THD< 20%, colour temperature - 6500K, surge protection 3KV in CM, IP-20 protected, meets LED IS specifications, Class - 1, Short circuit and over circuit protection, voltage range - 150 to 270 Volts AC, temperature range 0 to 50 Degree C, system efficency at luminaire level > 105 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting fixed, complete all as specified and directed.

S&F of LED batten luminaire surface mounted 2 feet system wattage of 10 watts and not less than 1000 lm with life time of 50000 burning hours with 70% of its initial lumen maintained. CRI > 80, power factor > 0.95, THD < 10%, color temperature > 6500 K , surge protection 2.5 KV in CM IP- 20 protected meets LED IS specifications, voltage range - 150 to 270 volts AC, temperature range 0 to 50 Degree C, system efficiancy at luminarie level ≥100 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire fixed, complete all as specified and directed.

S&F decorative type wall mounted luminaire (comet type) with unbreakable poly carbonate materials with 1x14 watt LED bulb B22 Base, complete all as specified and directed.

S&F LED 10 watts bulkhead fitting with powder coated die cast aluminium housing with glass/ non yellowing polycarbonate cover, IP65 Protection, System level efficacy of the Luminary is > 100 lm/W with a life class of 50,000 burning hours at L70 criteria, Power Factor >0.95, driver with Voltage range 150-270V, Temperature range 0 to 50 Deg, Driver efficiency >85%, THD<20%, CRI>80, Color Temperature-6500K, Surge protection of 4 KV, including connecting up with necessary PVC sheathed 3 core 1.5Sqmm copper conductor flexible wire fixed, complete all as specified and directed.

S&F surface ceiling mounted, round LED down light fitting 12 watts with die cast aluminium housing and system wattage of 12W, system efficacy at luminary level ≥ 80 Lumens/watt, 50000 burning hours, 6500K color temperature with CRI >80, Power Factor > 0.90, Driver should meet IEC compliant for safety with multi stage high Isolate CC-CV operated driver with voltage variation range - 150 to 270 Volts AC, and surge protection of 2.5 KV, and including connecting up with PVC sheathed 3 core 1.5Sqmm copper conductor flexible wire fixed, complete all as specified and directed.

S&F for angle Lamp holder with metalic ring, pvc/ polycarbonate type back plate with LED bulb 09 watt, 900 lumens out put, 6500K suitable for B-22 base, complete all as specified and directed.

S&F 35 W High efficient LED Street light fitting with pressure die cast Aluminum housing and has lenses specially designed for Street Lighting with polycarbonate cover. System level efficacy of the Luminarie should more than 80lm/W. The color temperature is around 6500 K with a color rendering index of 70. The luminaire is IP:66 protected. It has an electronic driver complaint to IEC safety standards with a power factor>.0.9, voltage variation range 120-270V, THD<20%, High and low protection along with a surge protection of 4 KV including provision of sutable dia GI light grade pipe1.5 meter length bend to shape and necessary clamps etc for fixing the light fittings on wall fixed complete as specified and directed.

S&F water heater storage type (Geyser) vertical type with suitable size of fastner and incl provision and connecting up of SS braided pipe with adopter for inlet and outlet water connection, having adjustable knob for temperature control and inner tank should be glass line coated complete all as specified of capacity 25 ltr having heating element 1.5/2.0 KW and not less than 5 star rating. Against BER, complete all as specified and directed.

S&F water heater storage type (Geyser) vertical type with suitable size of fastner and incl provision and connecting up of SS braided pipe with adopter for inlet and outlet water connection, having adjustable knob for temperature control and inner tank should be glass line coated complete all as specified of capacity 25 ltr having heating element 1.5/2.0 KW and not less than 5 star rating. complete all as specified and directed.

Supply and fixing ceiling fans complete three blade, Robust and reliable inverter motor (brush less DC Motor) powered by ECM technology, BEE 5 star rating for energy saving, rated Air delivery >220cum/min, AC single phase 230/240 V of size 1200 mm sweep including making connection with three core flexible copper cable pvc insulated of suitable length, down rods, electronic regulator and accessories complete. Against BLDC conversion, complete all as specified and directed. Note : Fan regulator Deemed be Quoted rate.

Repair and replacement of wall mounted fan 400 mm sweep, aerodynamic designed, air delivery ≥ 70 CMM, thermal over load protected motor, 3 blade white colour, 230 volts, 50 Hz, 1300 RPM with 90 degree oscillation and having speed & oscillation control by two pull cords system complete all as specified and directed.

S&F/ replacement of Ventilating Fan 200 mm sweep, 1250 RPM, non metallic resin body, single phase 240 volts AC 50 Hz and connecting up complete including louvers and provision of copper cable 3 core of size 0.5 sqmm complete all as specified and as directed.

S&F for Repair and replacement heavy duty exhuast Fan 230 mm sweep, 1400 RPM, metallic body, single phase 240 volts AC 50 Hz and connecting up complete including louvers and provision of copper cable 3 core of size 0.5 sqmm, complete all as specified and as directed.

S&F MCB DB SPN 12 way Horizontal, IP - 43 Protection double door 240 V AC 50Hz with for MCB SPN as incomer and SP MCBs as out going with tinned copper bus bar ,neutral link earth link complete all as specified and directed.

S&F MCB DB SPN 02 way, single door 240 V AC 50Hz, MCB SPN as incomer / out going complete all as specified and directed.

S&F MCB SPN 40 Amps 240 volts 10 KA 50 HZ 'B' curve complete all as specified and directed..

S&F MCB SPN 16 Amps 240 volts 10 KA 50 HZ 'B' curve complete all as specified and directed..

S&F MCB SP 6 - 32 Amps 240 volts 10 KA 50 HZ 'B' curve complete all as specified and directed..

BLANK

M&L for Sub main wiring complete with two runs of 4 Sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable with one run of 4 sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 20 mm dia non metallic rigid PVC conduit and conduit accessories concealed in walls complete all as specified and directed. Note:- (1) Two runs of cable, one run of earth continuity conductor and one run of PVC conduit shall be measured as unit length. (2) The damaged surfaces to be made good with plastering will be carried out by contractor and cost of the same deem to be included in the quoted rates. Nothing extra in this account will be admissible.

Supply and Laying jointing & testing XLPE insulated PVC sheathed armoured heavy duty electric cable with stranded aluminium conductor 1100 volts grade, cross sectional area 16 Sqmm 2 core complete fixed to floor/walls/ceiling with suitable size of clamp/saddles complete all as specified and directed.

M&L earthing complete with GI electrode 600x 600 x 6mm, thick buried directly in ground vertically in a pit of depth not less than 2.25 mtr below normal ground level (with top edge of earth plate not less than 1.50 mtr below normal ground level connected to GI strip 25 x 4 mm as earthing lead by means of bolt nuts, check nuts, and washers of brass connected including gun metal or phosphorus bronze of size 75x75x25mm drilled and screwed including 3 Nos 8mm dia 25 mm long hexagonal head screwed all as specified including excavation and earth work and disposal of surplus soil incl 40 mm GI tubing light grade and necessary fitting for protection of GI strip incl laying of alternate layer of charcoal dust and common salt PPC (1:2:3) type C-1 (using 20mm graded stone aggregate) for earth pit with 40 x 40 x 6mm MS angle iron frame for cover 40 mm thick (1:2:4) type B20 using 12.5 mm graded stone aggregate reinforced with 8 mm dia round bar @ 75mm C/C both way with MS handle 20mm dia plastering 15mm thick CM (1:6) internally and upto 150mm below ground level externally PGL funnel with ground wire mesh 20mm dia GI pipe Medium grade for watering complete all as shown on electrical plate No 3 of SSR Part-1 2009 and connected in earth test incl testing completed all as specified and directed. Note:- Galvanised strip and protection light grade GI pipe upto 7.5 mtr shall be deemed to be in the rates.

M&L for earth continuity conductor or main earthing lead fixed to wall on batten or recessed or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc of size 25X4 mm thick galvanised strip with duly fixed on suitable size of porcelain/ PVC insulato,r complete all as specified and directed.

M&L for fixing of GI tubing medium grade 40 mm dia fixed to wall / ceiling for hanging of ceiling fan (Approx length- 3 RM) including suitable size of fan hook as per site requirement and cement work including making good the disturbed surface with existing surface complete all as specified and directed.

S&F in reapirs sheet metal enclosure one way for independent mounting of 4 Pole MCCB, Including MCCB 4 Pole 250 Amps 25 KA, 415 Volts complete all as specified

Supply, laying in repairs of PVC under ground XLPE insulated heavy duty electric cables armoured with aluminium conductor, 1100 volts grade, cross sectional area 10 sqmm 2 core laying in trenches, fixed along wall, through GI pipe under floor complete all as specified.

Excavation in trenches n.exc 0.45 m wide and n.exc 0.60 m depth for laying of LT cables etc. and getting out in hard/dense soil soil soil complete all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming in layers n. exc. 25 cm complete all as specified and directed.

Removal of excavation material not exc 50 Meter and depositing where directed at a level not exc. 1.5 M above the starting point complete all as specified and directed.

M&L for dry river sand filling in trenches as cushioning to under ground cable provided with a layer of 8 cm deep before laying and 15 cm covering above the top edge of cable after laying complete all as specified and as directed by EIC. Note :- Punned thickness only shall be measured and paid.

Supplying laying sub class ‘B’ bricks old size with axis of the bricks perpendicular to the axis of the cable as in cable protection complete all as specified and directed.

S&F wall mounted angular Electric chimney black colour of suction power not less than 1200 Cum/Hr, Al casette with stainless steel outer layer ,touch control panel,3 speed motor with 250 watt with decorative smart cooker hood SS and glass ,energy efficent Led light with digital display , including ducting not less than 20 feet as per site required, complete all as specified and directed. Make. GLEN CAT Part No.CH6061 BLDC AC, LIVPURE CAT Part No. ELICA FL 600 SLIM HAC, HINDWARE CAT Part No. HOOD VENICE in HS SC FL LG 60

S&F switch modular type 25 Amps, 2 module 230 V, AC complete all as specified and directed.

S&F Instant Hot Water Geyser 3 Ltrs capacity,3 KW with corrosion proof thermoplastic external body, ISI approved with suitable size of fastner and incl provision and connecting up of SS braided pipe with adopter for inlet and outlet water connection, complete all as specified and directed.

M&L for Point wiring (concealed) complete with all accessories for TV cable drawn through in and including non metalic medium grade rigid PVC conduit, ISI marked, not less than 20mm dia for TV socket outlet on independent modular TV board,, complete all as specified and directed.

S&F Modular TV socket outlet 1 module on phenolic laminated sheet, complete all as specified and directed.

L G BUILDERS (BID ID -3129598)

ASSOCIATED CONSTRUCTION CO. (BID ID -3129691)

Adhunik Builders (BID ID -3128914)

M/s Puja Construction Company (BID ID -3129153)

M/S Chhavi Constructions Co (BID ID -3127831)

M/s Innovative Coolings and Constructions (BID ID -3128894)

Third Wave Services Pvt Ltd (BID ID -3127192)

M P TYAGI ENGINEERS AND CONTRACTORS (BID ID -3124533)

ASSOCIATED CONSTRUCTION CO. (BID ID -3129691)

Adhunik Builders (BID ID -3128914)

M/S Chhavi Constructions Co (BID ID -3127831)

L G BUILDERS (BID ID -3129598)

M/s Puja Construction Company (BID ID -3129153)

M/s Innovative Coolings and Constructions (BID ID -3128894)

Third Wave Services Pvt Ltd (BID ID -3127192)

M P TYAGI ENGINEERS AND CONTRACTORS (BID ID -3124533)