PROVN OF PM SHRI LAB FOR PM SHRI KENDRIYA VIDYLLAYA BAKLOH UNDER AGE (I) DALHOUSIE

Amount

Surface excavation not.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified and directed.

Excavation in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 mtr in depth and getting out in any type of soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25Cm, complete all as specified and directed.

Removing excavated materials/ soils, not exceeding 50mtrs and depositing where directed at a level not exceeding 1.50mtrs, complete all as specified and directed.

Excavation over areas, n.exc 1.5 m deep and getting out in any type of soil complete all as specified and directed.

Hard core of broken stone or boulders of gauge not exc 100 mm deposited ,spread and leveled in layer not exc 15 cm thick complete all as specified and directed.

Sand filling under floors or in foundations including watering and consolidation, complete all as specified.

PCC 1:5:10 (nominal mix) type D-2 (using 40mm graded crushed stone aggregates) as in foundation filling and mass concrete/ sub base complete all as specified and directed.

Pre construction anti termite treatment by treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area, complete all as specified.

Pre construction anti termite treatment by treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured), complete all as specified.

Pre construction anti termite treatment by treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall, complete all as specified.

PCC 1:3:6 (nominal mix) type C-2 (using 40mm graded crushed stone aggregates) as in foundation filling and mass concrete complete all as specified and directed.

PCC 1:2:4 (nominal mix) type B-2 (using 40mm graded crushed stone aggregates) as in foundation filling and mass concrete complete all as specified and directed.

Plain cement concrete 1:2:4 ( nominal mix ) type B-1 (using 20 mm graded crushed stone aggregates) as in copings and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork where required complete all as specified and directed.

RCC M-25 (Design mix) (using 20 mm graded crushed stone aggregates ) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

RCC M-25 (Design mix) (using 20 mm graded crushed stone aggregates ) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

RCC M-25 (Design mix) (using 20 mm graded crushed stone aggregates ) as in Columns, pillars, piers, posts and struts complete all as specified and directed.

RCC M-25 (Design mix) (using 20 mm graded crushed stone aggregates ) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Extra fro forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex tra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and directed.

Precast cement concrete type B-1, 1:2:4 (20mm graded crushed stone aggregate) as in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings, kneelers, apex stones, pier caps, coloums, posts, boundry pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling) etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and setting in cement mortar 1:6 complete with joints to match, complete all as specified.

Use & waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batterfor rough finished surfaces of concrete flat, complete all as specified & directed.

Use & waste of form work to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc alo splays between floors and beams for rough finished surfaces of concrete, complete all as specified & directed.

Use & waste of form work to Form work to sides of pillars, posts, struts, piers, columns and stanchions for rough finished surfaces of concrete for Square, rectangular or polygonal surface, complete all as specified & directed.

Use & waste of form work to suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished surfaces of flat concrete, complete all as specified & directed.

Brick work with old size fly ash bricks, class 7.5, straight or curved on plan exc. 6 metre mean radius built in cement mortar 1:6 (01 cement : 06 coarse sand) all as specified & directed.

Walling of random rubble stone masonry uncoarsed, well bonded bedded and soilidly hearted built in CM 1:6, complete all as specified and directed.

Extra over stone walling of granite, trap or basalt stone for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses with maximum depression on face from straight edge held against the dressed surface not exc 20mm, complete all as specified & directed.

Powder coated, Anodised aluminium frame powder coated for doors, windows, ventilators with one or more rebates including joining cleat for fixing of glass, particle board,aluminium frame etc complete all as specified and directed.

Pressed steel frame using 1.25 mm thick PBI sheet (size of frame 105 x 60 mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock/ strike plate etc and filling with PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in back of chowkats complete all as specified.

35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Powder coated, Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed.

Aluminium handles cast type anodized of size 150 mm complete all as specified and directed.

Aluminium anodized barrel tower bolt of extruded section of size 200 mm and fixed complete all as specified and directed.

300mm long aluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

Galvanished mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanished wire staples complete all as specified and directed.

Sheet glass, 4.8mm thick ordinary quality and glazing with oil putty in squares n.exc 0.5 sqm each pane complete all as specified and directed.

Mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete drilled for fixing of steel sheeting or other covering, doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing cconforming to grade Fe 410 -W (Gde-E- 250) quality-A, complete all as specified and as directed.

Mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard sectionand fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in- charge

75mm thick PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregates) as in sub base complete all as specified and directed. .

30mm thick PCC 1:2:4 type B-0 (using 12.50 mm graded crushed stone aggregates) as in levelling course , surface finished even and rough to receive to finish , complete all as specified and directed.

Plain cement concrete , 1:3:6, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 75m thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over and including 15 mm thick screed base in cement mortar 1:6 over and complete all as specified and directed.

Machine cut kota stone slab flooring 20-25 mm thick of size not less than 550 mm X 550 mm as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in floor etc, laid over and including 15mm screed layer in cement mortar 1:4 (1 cement : 4 coarse sand), cutting, rubbing, grinding and polishing to achieve mirror finish, laid over PCC subbase complete, all as specified.

Machine cut kota stone slab 20-25mm thick as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab,as in in skirting, dados, risers to steps etc, laid over and including 10mm thick rendering in cement mortar 1:4 (1 cement : 4 coarse sand), cutting, rubbing, grinding and polishing to achieve mirror finish complete, all as specified.

Chequered cement concrete coloured tiles, homogenious texture glossy finished , chemically coated machine pressed 30 cm x 30cm x 25mm thick set, jointed and pointed in near cement slurry in floor with gray cement and pigment and including 20 mm thick cement screed in cement mortar 1:4 over and including , complete all as specified and directed.

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified.

Rendering cement plaster 10mm thick in cement mortar 1:6 (1 cement : 6 coarse sand) in two layers (5mm thick first layer and 5mm thick second layer) on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified.

Rendering cement plaster 10mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers (5mm thick first layer and 5mm thick second layer) on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified.

Rendering cement plaster 20mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) on stone masonry surfaces or surface other than fair face of brick-work, surface finished even and smooth without using extra cement, all as specified.

5 mm thick rendering in cement mortar 1:3 on concrete surfaces as in ceiling , surface finished even & smooth without using extra cement complete all as specified and directed .

Flush pointing to random or polygonal rubble, uncoursed or brought upto courses in cement mortar 1:4, complete all as specified.

APP based polymeric membrane minimum weighing 3.6kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application over one coat of primer conforming to IS: 3384-1986 over plastered surfaces @ 0.40 litres/Sqm of density 0.87-0.89kg/litres at 25°C and viscosity 70-160CPS ( primer shall be of same make as of memebrane),complete all as specified. Note : The membrane shall be laid with 100mm side overlap and 150mm end overlap, fixed using butane torch and sealing all joints after preperation of surface as per manufacturer's instructions and finished with applying one coat of bituminpus paint @100gm/ Sqm on top of membrane , complete all as specified.

Supply only liquid water proofing compound, complete all as specified.

Preparation of new plastered or unplastered surfaces of walls and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces including 2mm thick wall care putty (applied in two layers), finished smooth with sand paper complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification, over a coat of primer over and including plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth, finished smooth with sand paper complete all as specified and directed.

Three coats of white wash on newly plastered or un plastered, previously undecorated ceiling surfaces including preparation of surfaces complete, all as specified.

Preparation of new plastered surfaces or un plastered, previously undecorated wall surfaces and applying two coats of cement base paint, complete all as specified and directed.

Preparation of new wooden surfaces of any description , not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparation of new steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

G I tubing medium grade of 15 mm bore with all fittings and fixtures fixed to wall and ceiling or laid in floor/trenches complete all as specified and directed.

50mm bore, Low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. cm as in weep holes, complete all as specified.

G I tubing medium grade of 25 mm bore with all fittings and fixtures fixed to wall and ceiling or laid in floor /trenches complete all as specified and directed.

Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc., all as specified.

Sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified.

Bib tap, cast copper alloy ,chromium plated, fancy type , screwed for iron pipe or for brass ferrule of 15 mm bore complete all as specified and directed.

Gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed bore dia of pipe 25mm complete all as specified and directed.

75mm dia PVC(SWR) pipe single socketed with rubber ring joints, laid/fixed to tranches or in floor or walls, complete all as specified and directed.

75 mm dia PVC(SWR) bend, any radius complete all as specified and directed.

75 mm dia PVC(SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

Cutting the existing CI/GI pipe (40 to 150mm bore) or screwing existing CI/GI pipe for addn/altn as required at site including GI fittings , complete all as specified. Note : Earth work shall be measured and paid seperately.

Rotational moulded polyethylene water storage tank 1000 Ltrs capacity four layered (ISI Marked) cylinderical vertical with closed top, hoisted and fixed in position with ball brass valve, high pressure with PVC float valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line complete all as specified.

Black board of size 3.00m x 1.40m , fixed in poistion, complete all as specified.

Point wiring for one light/fan/call bell point controlled by one 5/6 Amp switch with 1.5 Sqmm two single core multistranded copper conductor FRLSH, PVC insulated (unsheathed) heavy duty cable 1100 volts including continuous earth wire of size 1.5 Sqmm copper conductor multistrand FRLSH, PVC insulated (unsheathed) drawn into concealed rigid non-metallic PVC conduit Med Grade ISI marked not less than 20mm wide of 1.8mm wall thickness ISI marked including modular GI sunken flush box (Pressed steel powder coated Modular GI sunken flush boxes and cover plates of any way i.e. 1 to 8 way as per site requirement suitable for modular switch/socket) for mounting switches, sockets, fan regulators etc & making good to disturbed surfaces as well as matching with existing whitewash colour/surface complete all as specified and as directed for the following:- (a) Wiring shall be done by using proper colour coding (b) Earth wire shall be of green colour (c) On RCC roof/ceiling PVC conduit shall be provided on surface with proper fixing clamps all as directed.

All as per serial item No '98' above, but for one 3 pin 5 Amps socket outlet on the same board all as specified and directed.

All as per serial item No '98' above, but for one 3 pin 5 Amps socket outlet on the independent board all as specified and directed.

All as per serial item No. '98' above but for 3 pin 15 Amps socket out let independent with 2.5 Sqmm PVC copper conductor cable and and PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, all as specified.

Modular switch 1 way 6A, 1 module, all as specified.

Modular switch 1 way 16A, 1 module, all as specified.

Modular Socket, 6A - 2/3 pin combined 2 module, all as specified and directed.

Modular Socket 6A/16A - 2/3 pin combined 2 module, all as specified.

Ceiling rose, 65 mm to 50 mm, two to three terminals, PVC/ Polycarbonate, insulated body fixed on PVC block, all as specified.

Modular fan regulator, step type, 2 module, all as specified.

Decorative, surface mounting, dome shaped pendant light , upto 1 metre hanging length, dome shaped in green & black finishes with 7.5 W A60 LED Filament Lamp Black , complete all as specified and directed. Make: Havells cat part No. LHFHDPE1TN1K020 or equivalent in Appx

LED Luminaire 600mmx600mm, 36 watt, 6500K, Ultra modern recess mounting luminaire with high performance LEDs, suitable for mounting with Armstrong/Grid ceiling, complete all as specified Make: Havells cat part No. LHEBAEP7IW1W036 or equivalent in Appx

50 Watt Street Lights with best in class design & Robust heat sink along with class leading IP, IK & Surge protections for long lasting performance. with IP65 protection and impact resistance of IK08. connecting with PVC insulated three core flexible copper conductor of suitable size to fitting including bracket made up of 32mm dia GI pipe light grade 1.5 metre long and bent to shape required, complete all as specified Make: Havells cat part No. LHEXBAP7PN7J050 or equivalent in Appx

LED Bollard cone type light fitting , IP 65 protection , complete with all accessories , fixed in ground including necessary earth work and foundation complete all as specified Make: Havells cat part No. CONEBLS8WLED857PSYMTOPC or equivalent in Appx

Sheet metal enclosures for DBs when MCBs to be used, triple pole and neutral, 6 way, double door, 415 volts with 200 Amp rated bus bar completed all as specified.

Sub main wiring with two single core PVC insulated cable 1100 volts grade with copper stranded RLS conductor of size 2.5 Sqmm (2 single run) with one continuous FRLS copper earthing lead wire of size 2.5 Sqmm and drawn into PVC conduit/ casing & capping with all fittings/ accessories, junction boxes 1 to 4 way 20mm dia, cutting chases, making good in cement mortar (1:3), finishing surfaces to match with existing and connected to common earth dolly complete and as directed. Note :- Two run (each run of 1 RM) of 2.5 sqmm copper conductor and one RM of earth wire of 2.5 Sqmm, shall be measured as one RM).

MCB TPN , 40 to 63 Amp,415 Volts, 10 KA all as specified.

MCB SP 6 to 32 Amp, 240 Volts, 10 KA all as specified.

MCCB , 4 Pole , 415 Volts, Adjustable type, 160 Amps with breaking capacity 36 KA, Complete all as specified.

Supply and installing of Electric Water storage heater of ABS body type 25 Litre Capacity with rated power 2 KW, 5 star rated, vertical type, thermally insulated Mild steel tank with, glass line coating inside he tank alongwith glass line incoloy heating element with anti corrosive magnesium anode, NRV, theremostate, indicators and temperature adjustable knob including steel braided flxible connection for pipe of size 15mm dia bore GI hexagonal adopeters./ Nuts on both sides of inlet (Cold water supply) & outlet (hot water supply) and including provision of wall mouting arrangement and mounting on wall with suitable size of anchor bolts with complete connection of water including testing after installation complete all as specified and as dierected by Engr-in-Charge.

Exhaust fan, 300mm sweep, steel body AC single Phase. 230V complete with with, blades, and frame and louvers including provision of cable copper flexible PVC three core 23/0.0076 from ceiling rose to fan, complete all as specified. Note : Quoted rate shall include for making hole in wall for grouting, fixing the fan on outer side of wall with suitable size anchor bolt and making good disturbed surfaces without ant extra cost.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC), complete all as specified.

Sand cushioning to under ground cables provided with a layer of sand 8 cms thick before laying the cable and 15 cms thick after laying the cable complete all as specified and directed.

Un-reinforced precast concrete cable cover, Class LV, Type I, flat, size 250 mm x 150mm x 40mm all as specified and directed.

XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with multi-standard aluminium conductor, 1100 volts grade, cross sectional area 35 Sqmm, 3.5 core, laid in trenches or passing through pipes, including making necessary connections at both ends, complete all as specified and directed.

XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with multi-standard aluminium conductor, 1100 volts grade, cross sectional area 16 Sqmm, 4 core, laid in trenches or passing through pipes, including making necessary connections at both ends, complete all as specified and directed.

Street Light timer panel 3 phase maximum load capacity, maximum load 6KW capacity, Contactor Rating 32 Amp, MCB Rating 40 Amps TPN with 24 hours working digital timer 24 hours, outdoor type panel with canopy and locking arrangement complete with all incoming and outgoing cable connection, complete all as specified. Havells cat part No. IHXTS03060 or equivalent in Appx

Supply, installation , Commissiong and Testing of totally enclosed LT panel box outddor type, CPRI approved, LT 440 Volts, 50 Hz , 3 Phase 4 wire supply system, double door type, having independent cabin including locking arrangement for each MCCBs, floor mounted factory fabricated weather and vermin proof protection class IP 55 made out of 3.15 mm thick MS Sheet CRCA Sheet on angle iron 50X50X6mm frame of size suitable to incorporate and including following accessories with front and rear opening doors, handle type locking arrangement powder coated internally and externally shall have angle iron legs made out of angle iron 40x40x6mm and embeded in PCC foundation of size as required or approved by manufacturers in PCC 1:3:6 Type C-2 , using 40 mm graded crushed stone aggregate ( 150mm below GL and 100mm above GL) as recommended by manufacturer or directed including earth work complete comprising of following:-

Incoming:- (a) MCCB having current rating 400 Amps with rupturing cap 25 KA (Adjustable Thermal & Adjustable Magnetic) , AC 415 Volts,triple pole anu neutral, complete with spreader links. (Qty -01 No)

Outgoing:- (a) MCCB having current rating 125 Amps with rupturing cap 25 KA (Adjustable Thermal & Adjustable Magnetic) , AC 415 Volts,triple pole and neutral, complete with spreader links. (Qty -06 Nos) (b) Multifunctional digital panel meter with LCD display flush mounting type of size 96x96mm, accuracy class 1, suitable for CTs with secondary current 5A having provision of display parameters such as voltage, Amp, Power factor , KW, KV etc. ( Qty-01 No) (c) LED phase indicator lamp ( Qty- 01 set of three) (f) 600 Amp rated Bus bar chamber comprising 4 Nos Aluminium Strip bus bars PVC insulated made of aluminium strip of size (40 x 5) mm. PVC sheathed with colour coding.

Note : (i) Incoming and outgoing cables shall be fixed with appropriate size of thimble. (ii) Apron shall be provided at bottom of protection of cable to avoid entry of vermins, raptiles. (iii) Entries of all sizes of cables in panel should be done through adequate size of metallic cable glands. (iv) Layout diagram of panel shall be produced by contractor for approval of AGE (I) before placing order to manufacturer and panel shall be brought at site as per approved drawing

Location : Main LT Panel for KV School

Eshaan Construction Co. (BID ID -3403951)

M/S WALIA ENGINEERS (BID ID -3400926)

MS ROSHAN LAL THAKUR (BID ID -3403132)

M/S AMAN ENTERPRISES (BID ID -3397804)

R.K.CONSTRUCTION ENGINEERS (BID ID -3403986)