ADDN ALTN TO ROOF TREATMENT SAMAGRI BHAVAN, EXISTING WORKER CHANGING ROOM AT CERTAIN STORE HOUSES AND PROVN OF EMERGENCY EXIT FOR TRAINING CELL (NS-152) AT MO (MB) GHATKOPAR UNDER GE (NW) BHANDUP

Amount

Dismantling wrought iron or mild steel work of any description not other wise provided for complete all as specified and directed.

Dismantling of wall and ceiling board (fibre, pulp,insulation etc) or insulation boards/slabs/blankets any thickness, including cover fillets etc complete all as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutter from the frames) exceeding 1.5 Sqm but not exceeding 4.0 Sqm each complete all as specified and directed.

Taking down chowkets or frames not exc. 1.5 Sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down cement or cement lime plaster of any description on brick or stone wall including raking out joints, hacking for key, scrubbing down with water etc and disposing off the rubbish outside MD land complete all as specified and directed.

M & L for rendering 12 mm thick in CM 1:6 on brick walls or concrete surfaces and finishing the surfaces even and smooth with sagol finish complete all as specified and directed.

M&L Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. complete all as specified and directed.

M&L for 20 to 25mm machine cut pre polished kota stone slab for flooring laid over cement screed bed and jointed with grey cement slurry mixed with pigment to match the shade of of the slab including rubbing and polishing including over 15mm thick screed bed or bedding layer in CM1:4 complete all as specified and as directed.

M&L precast cement concrete block masonry in PCC 1:3:6 type C1 with solid block exc 10cm in width and setting in CM 1:6 complete all as specified and as directed.

M&L for RCC 1:1.5: (20mm graded aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for Formwork to sides and soffits of floor or roof beams, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.

S&F aluminium section in doors/windows/ventilators ,kitchen cupboards, built n almirah doors any type, powder coated in approved colour (Thickness of powder coating not less than 50 micron), aluminium section (medium weight of series 'B') or section as directed by Engineer-in-Charge, cut to size, jointed together with cadmium plated steel screws including rubber beading or gasket for aluminium sections for fixing glass/XPM jali or for fixing bakelite sheet and all necessary fittings complete, screws, plugs for fixing screws, etc all as specified and directed (Make : JINDAL/HINDALCO) Notes : (i) Weight of aluminium sections shall only be measured.

Supply only stainless steel wire cloth of 0.63 mm nominal dia of wire and average width of aperture 1.40 mm , fixed in aluminium windows complete all as specified and directed.

S&F aluminum anodised grill DG- 202 ( 10 mm x 7.5mm ) of Deco grill or equivalent fixed with 'F' section size not less than 20.60 x 15.20 x 1.5mm thick of approved make all as specified and directed. Note : (i) Make shall be of M/s Decogrille of M/s Associated Groups or equivalent as approved by the GE. (ii) Minimum thickness of anodizing shall be 15 microns.

S&F for 20mm dia curtain rods anodised aluminium alloy, power coated with fixing brackets, stops, rollers etc complete all as specified and directed

S&F II nd class Hard Wood as in plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints etc complete all as specified and directed.

S& F 2nd class HW 35 mm thick,plain, framed, panelled shutters (any numbers of panels), with pannels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face neneers;fixed to chowkats complete all as specified & directed.

S&F alluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast alluminium alloy and fixed of length of bolt 300 mm complete all as specified and directed.

S&F 100 mm stainless steel butt hinges,complete all as specified and directed

S&F 150mm length aluminium anodised barrel tower bolt of extruded section complete all as specified and directed

S&F 150 mm length extruded aluminium alloy handles,fabricated type, anodised complete all as specified and directed

S&F PVC insulation panels of 40mm thick with EPS stuck to 1mm PRINTED PVC sheet suitably placed in false ceiling grid made of Aluminium/G.I./M.S. as per specification directed.

M&L for preparation of old decorated surfaces of wall by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and thereafter applying with roller Two coat of oil bound distemper including application of white cement based wall care putty finish for smooth finish.etc complete all as specified and directed.

M & L for preparation of new plastered surfaces of walls and applying Two coat of oil bound distemper including application of Birla wall care putty for smooth finish.etc complete all as specified and directed.

Chipping, removing carefully loose/damaged concrete including plastering (total thickness exceeding 40mm but not exceeding 60mm ) from surfaces of RCC members, in any location by low impact Hammer/Breakar without damaging the structure & cleaning the surfaces with wire brush etc and disposal of debris out side MOD land complete all as specified and directed. Note : 1) Hard concrete shall not be removed by force

M&L for cleaning existing reinforcement with wire/ rotary wire brush to a shining bright finish, making the surfaces free from loose material, dirt etc complete and applying two coats of alkaline rust converting primer conforming to ASTM-B-117 of make. "Feovert" of "Krishna Conchem" OR "Roff Rust Cleaner' of 'Pidilite' OR 'Shali Rustoff' of 'STP Ltd', on rebars with time interval of 1 hour between the coats, complete all as specified and directed. (Note :- Mode of measurement: superficial area of concrete will be measured.)

M&L for carry out application of ‘Bi-polar migratory corrosion inhibitor' [Make : M/s. Krishna Conchem (EPCO KP-100) / BASF (MasterProtect®8000Cl)] on RCC surfaces, complete all as specified and directed. (Note :- Mode of measurement: superficial area of concrete will be measured.)

M&L for Anticorrosive Treatment to Reinforcement using IPNET-RB of M/s Krishna Conchem or Epoxy Zinc Primer of M/s. Dr. Fixit by application on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be done by brush after cleaning/wire brushing to the exposed steel surfaces complete all as specified and directed . Note :- Mode of measurement: superficial area of concrete will be measured.

M&L for Epoxy bond coat of Make Fosroc (NITOBOND-EP) OR EPOXY BONDING AGENT of Dr. Fixit OR equivalent of M/s. Krishna Conchem as approved by GE over exposed concrete surfaces prior to application of any type of mortar / concrete to ensure bond between old concrete & new concrete/ new mortar by brush application, complete all as specified and directed.

M&L for building up the profile of structural members using polymer modified mortar from M/s Krishna Conchem (Molith PMM) OR Polymer mortar HB of Dr. Fixit, exceeding 20mm thick and not exceeding 40mm thick in two layers, each of equal thickness including levelling, profilling etc, complete all as specified and directed.

M & L for TMT steel bars 10 mm dia and over, cut to length , bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or escuring with clips quality confirming to complete all as specified and directed.

M&L for post construction ATT treating soil under existing floor at internal junctions with wall using chemical emulsion @ 1.00 ltr per hole , 300 mm apart including drilling and plugging 12 mm dia holes with CM 1:2 to match the existing floors , all as specified and directed.

M&L for treating points of contact of wood work with masonary / concrete by chemical emulsion (in oil or kerosene based solution) @ 0.50 litre/hole by drilling 6 mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same all as specified and directed.

Excavating in post holes in soft/ loose soil (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed.

Demolition of brick work/ stone boulder built in cement mortar or cement lime mortar of certain portions including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortor 1:6 complete all as specified and directed.

M&L for plastering in CM 1:6, 10 mm thick on walls finished even and smooth w/o using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces of brick work in CM 1:6 and 5mm thick in CM 1:4 including water proofing compound, finishing even and smooth without using extra cement. (WPC shall be measured and paid separately)

S&F Mild steel TMT bars 5mm dia and over upto and including 10mm dia for stirrups cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified

S&F MS Stairs (framed) including stringers, treades, landing, balusters, hand rails etc. including cleats, brackets, etc. fixed with angle cleats or any other material complete all as specified and as directed by Eng-in -Charge Fe 410-W (Gde-E-250 quality-A)

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment. ( Fe 410-W (Gde-E-250 quality-A)

S&F aluminium anodised barrel tower bolts of extruded section 200 mm size.

S&F aluminium extruded door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed

Supply and fix for 6mm thick bakelite sheet prelaminated both side with decorative choice laminations with aluminium frame cuboard shutter work complete all as specified and directed.

M&L for preperation of new surfaces of any description , over 10cm in width or girth not otherwise described and applying two coats of anti corrosive epoxy paint over a coat of epoxy primer, over a coat red oxide on steel sufaces complete all as specified and directed.

M&L for two coats of antifungal paint (Apex ultima Protek of Asian Paints or equivalent in approved makes) over a coat of exterior primer (Professional pack of Asian Paint) on newly prepared plastered external surfaces and including scaffoldings and cradle including hoisting and lowering as required with bracing, support complete all as specified and directed by Eng-in-Charge

M&L for two coats of antifungal paint (Apex ultima Protek of Asian Paints or equivalent in approved makes) over a coat of exterior primer (Professional pack of Asian Paint) on old plastered external surfaces and including scaffoldings and cradle including hoisting and lowering as required with bracing, support complete all as specified and directed by Eng-in-Charge

Dismantling of roof terracing cement / brick concrete (un-reinforced) and existing water proofing treatment of any thickness in any position and of any portion from top of roof of building, cleaning surface of roof with wire brush / mechanical brush and with water thoroughly to remove all dust / dirt and loose particles to expose base concrete roof slab and removal of rubbish / demolished material out of MD land complete all as specified.

M&L for PCC 1:2:4 Type B0 using 12.5 mm graded aggregate with 2% by weight of cement or as per manufacturer's instructions water proofing as in levelling course, haunching, coping and similar works over RCC roof surface and RCC over head tank top surface including rounded or chamferred on edges and formwork etc all as specified and directed.

M&L for supply and application of 7 layer SHR water proof coating system on leaking concrete surface by thorough surface preperation, opening of cracks, followed by one absorption coat of thermacool WP51, nano modified, UV resistant elastomeric clear coating having min 50% solids, filling of cracks, then over coating with sand witch coat of elastomeric ( Thermacool WP51 +Cement) water proofing layer with 80 GSM non woven fibre mesh, application of 3rd coat of elastomeric water proofing layer having 450% elongation ,tensile strength min 2.2MPa and then top coated with two coats of thermacool 0.3c pure acrylic based UV resistant , non yellowing bio organism resistant (anti fungal, anti bacterial) solar reflective coating confirming to BIS STTD IS 17218: 2019 with pull off adhesion 2.8MPa, passes 20 hrs accelerated durability test, suitable for all types of cementitious surfaces, white colour, matt, surface coverage 3.25sqm/ltr/2 coat ,DFT 100-120 microns using brush, roller, airless spray gun as applicable and application is to be done with Thermacool approved applicator with ten year guarantee all as specified. Or equivalent make of Dr.Fixit/ BASF/Fosroc with their specification with authorised applicator with 10 year guarantee

M&L for Supply and application of 5 layer SHR water proofing coating system on leaking concrete surface by thorough surface preperation followed by one absorption coat of Thermacool WP 51, nano tech modified, UV resistant elastomeric clear coat having min. 50% solids, then over coating with 2 coats of Thermacool WP 51 + cement mixture as water proof coating having +450% elongation, tensile strength min 2.2 MPa and then top coated with 2 coats of Thermacool 0.3 C pure acrylic based UV resistant, non yellowing bio organism resistant ( anti fungal, anti bacterial) Solar IR heat reflective coating confirming to BIS STD IS 17218:2019 with pull off adhesion 2.8 MPa, passes 20 hrs accelerated durability test , suitable for all types of cementitious surfaces, white colour, matt , surface coverage 3.25sqm/ltr/2 coat , DFT 100-120 microns using brush roller, airless spray gun as applicable. The product should have been tested at IIT or NABL approved lab and application is to be done by Thermacool approved applicator only. Or equivalent make of Dr.Fixit/ BASF/Fosroc with their specification with authorised applicator with 10 year guarantee

Taking down carefully unserviceable point wiring of any type & pattern (Light/Fan/Socket or power) including unserviceable fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings of any type etc and making good disturbed surfaces of walls/ roof etc complete all as specified and directed.

M & L for point wiring complete with proper colour coding using, 1100 Volts grade, 1.5 Sqmm, PVC insulated FRLS, unsheathed wire with multi stranded copper conductor confirming to IS-694, Part II, ISI marked drawn in and including PVC conduit (minimum 20mm dia) concealed in wall etc (also including cutting chiseling in wall and making good the same in CM 1:3 to match with the adjoining surfaces) with all accessories, fittings, PVC junction boxes etc, also including 1.5 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts multistranded copper conductor green colour as continuous earth wire connected to common earth dolly all as specified and directed for one light point /fan/bell point controlled by one one way switch, complete all as specified and directed. Note: Modular flush box and inner/outer plates measured and paid separately.

M&L for ceiling rose three terminals AC 240 volts 50Hz complete all as specified and directed.

Supply and fixing modular ceiling fan regulator 120 watt 2 module complete all as specified and directed.

M&L for switch modular one way 6/5 amps 1 module complete all as specified and directed.

Supply and fixing modular metal flush box 6 module complete all as specified and directed.

Supply and fixing modular metal flush box 12 module complete all as specified and directed.

Supply and fixing modular white cover plate with frame 6 module complete all as specified and directed.

Supply and fixing modular white cover plate with frame 12 module complete all as specified and directed.

Material and Labour for tube light fitting LED 20 watt with decorative end caps made out of CRCA sheet powder coated complete with housing with aluminium heat sink on back of leds ,power factor >0.9,having inbuilt surge protection device for overvoltage protection with all accessories prewired and making connection with 3 core copper flexible cable of size 23/.0076 from ceiling rose/PVC connector to light fitting and shall be fitted on new plastic square/round block complete all as per specified and directed. M

Deduct Credit for Demolished/ Dismantled material Rs. (-) 11495.00 (Minus) as listed in Schedule of Credit Note1: Tenderers will not quote against this item being a tentative amount to be considered to arrive at the 'Contract Sum' Note 2:- The tenderer must keep in mind when quoting rates against items out in multiple store house having height 4 mts to 7 mts. Necessary scaffolding and saftey measures required during execution of work are including in this items.

M/s Qureshi Construction Co

Joy builders

S R INFRASTRUCTURE