PROVN OF LT UG CABLE WITH CONNECTED WORKS AND AREA LIGHTING FOR GOLF PUMP HOUSE, SUBSTATIONS AT VARIOUS LOACATIONS AND CSS-1, CSS-2 OF MAP OFFRS ACCN AT DSSC WELLINGTON.

Amount

Supply, laying, jointing, connecting & testing XLPE insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 400 Sq mm 3.5 core in trenches / through GI pipe / fixed along with pole structure etc with all fixing & connecting accessories complete all as specified & as directed. Make :Havells/Finolex/Polycab/Gloster

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for laying of cables, pipes etc and getting out in hard/ dense soil complete all as specified and as directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers n.exc 25cm thick with excavated soil complete all as specified and as directed.

Removing of excavated material (soil) to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed.

M & L for GI pipe medium grade 100mm bore with all running fittings (ISI Marked), laid in trenches, under road or fixing on wall/pole/crossing drain/nallah etc., complete all as specified and directed. Make : TATA/JINDAL/PRAKASH/ ZENITH/ SWASTIK. Note : wherever the GI pipes are to be fixed on wall/pole/crossing drain/nallah etc shall be fixed with suitable fixing accessories like/incl nuts, bolts, washers of suitable size/number as directed by Engr-in-Charge and the quoted rates are deemed to be included these provisions.

M & L for cutting the existing hard standing /PCC /WBM road at a depth not less than 45 cm and 25 cm in width for passing of cable through GI pipe, returning filling in, complete including finishing the surfaces by providing top 25 cm thick cement concrete (1:3:6) type C-2 (using 40 mm graded stone aggregate), bottom filled with excavated earth and finishing to a uniform smooth surface complete all as specified and directed.

M & L for providing sand cushioning for protection of UG cable in trenches with M-sand approved quality including filling ,spreading and punning down to desired thickness complete all as specified and as directed. Note: Punned thickness only shall be measured.

Supply and laying sub class "B" bricks in trenches for protection of UG Cable with width equal to length of bricks, laid dry & flat complete all as specified and as directed.

S & F cable jointing kit for 1.1 KV (Earthed) grade cable for OUTDOOR termination heat shrink type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 400 Sq mm complete all as specified and as directed. Make : RAYCHEM/ DENSONS/ M SEAL/ BIRLA 3M / YAMUNA GASES AND CHEMICALS

S & F cable jointing kit for 1.1 KV (Earthed) grade cable for STRAIGHT THROUGH heat shrink type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 400 Sq mm complete all as specified and as directed. Make : RAYCHEM/ DENSONS/ M SEAL/ BIRLA 3M / YAMUNA GASES AND CHEMICALS

Supply, laying, jointing & testing XLPE insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 240 Sq mm 3.5 core in trenches / through GI pipe / fixed along with pole structure etc., with all fixing & connecting accessories complete all as specified & as directed. Make :Havells/Finolex/Polycab/Gloster

Supply, laying, jointing & testing XLPE insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 Sq mm 4.0 core in trenches / through GI pipe / fixed along with pole structure etc with all fixing & connecting accessories complete all as specified & as directed. Make :Havells/Finolex/Polycab/Gloster

S&F for GI pipe medium grade 50mm bore with all running fittings (ISI Marked), laid in trenches, under road or fixing on wall/pole/crossing drain/nallah etc., complete all as specified and directed. Make : Make : TATA/JINDAL/PRAKASH/ ZENITH/ SWASTIK. Note : wherever the GI pipes are to be fixed on wall/pole/crossing drain/nallah etc shall be fixed with suitable fixing accessories like clamps incl nuts, bolts, washers etc of suitable size/ number as directed by the Engr-in-Charge and the quoted rates are deemed to be included these provisions.

M & L for cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) as in foundation, filling mass concrete for pole foundation & finishing the surface fair and even incl necessary formwork complete all as specified & as directed.

M & L for PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) for coping of poles etc & finishing the surface even & smooth without using extra cement incl necessary formwork complete all as specified & as directed.

S&F for steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts & screws as specified type 410 SP-31 (9.0 metres long) complete in the location as specified and directed by Engr-in-Charge. Note : (i) Earthwork and PCC shall be measured and paid separtately. (ii) Design/Drawing of the poles incl dimension is to be obtained from the OEM/Auth Distribution/Dealer & is to be got approved from the Engr-in-Charge & GE before placing final order to the manufacturer/Supplier. (iii) Original Purchase Vouchers & Test Certificate is to be submitted to the Engr-in-Charge for verification & record. (iv) Cost of 02 coats of Aluminium painting of the poles over a coat of red oxide primer after preparation of surfaces complete is deemed to be included in the unit quoted rates.

M & L for cable route indicators for LT cable with CI plate with embossing "MES LT CABLE" with "Arrow symbol" and cable size and voltage written on it. The CI path indicator shall be fixed on MS angle iron of size 25x25x5mm with suitable PCC base complete. The cable path indicators shall be erected at the time of refilling the trenches and the cable path indicator shall be painted as - “BROWN” for LT Cable complete all as specified and as directed. Note : (i) Quoted rate is deemed to be inclusive of earth work and PCC. (ii) The spacing between two consecutive cable route indicators shall not be more than 50.0 meters & also shall be provided at each & every bend or corner.

S & F LED flood light fitting of capacity 150 Watts, Power factor >0.95, colour temperature >5700 K, luminous efficacy >100 lumens/watt, IP-65 including electronic driver (SMPS based constant current supply with lower THD, output open/short circuit protection, phase to phase protection, over voltage protection, surge voltage protection etc.) unit suitable for working voltage 140-270V AC, 50 Hz, pressure die cast aluminium housing and finishing epoxy powder coated with all accessories as per manufaurers instructions of Make: HAVELLS, Cat No : JETA PROPLUSFL150W LED757LTG or techno-commercially equivalent in PHILIPS/JAGUAR and connecting up including necessary fixing arrangements on steel poles etc. complete all as specified and directed by Engr-in-Charge.

S & F loop in-loop out fuse junction box of Make : Sintex, Cat No: GSJB-2014 or techno-commercially equivalent in Hensel/OBO, internal dimension 200 x140 x 95mm (min dimensions) made out of FRP sheet with weather proof canopy and locking screw fitted with and incl 6 Amps MCB, SP of rating 10 KA, C Series - 02 Nos, 50 Amps rated 4 Way connectors for 3 phase and neutral incoming/out going, mounted in the box, fixing on steel tubular including necessary aluminium clamps, suitable glands, lugs, nuts and bolts of suitable size/type complete all as specified and directed by Engr-in-Charge.

NOTE for Item Nos 18 & 19 : (i) Design / drawing / BOM / Technical specifications / comparative analysis of the Items is to be got approved from the Engr-in-Charge & GE before placing final order to the manufacturer whereever techno-commercial equivalency w.r.t. given Cat/Part ref is concerned. (ii) Anything missed out in the technical specifications but technically required for efficient working is deemed to be included in the quoted rates. (iii) LM 79/80 test certificates etc. in respect of the LED fittings is to be ssubmitted to the Engr-in-Charge. (iv) Cost of suitable fixing arrangements as decided by the Engr-In-Charge/GE is deemed to be included in the unit quoted rates.

Supply, install, commissioning and testing of multi stage submersible pump set of capacity not less than 5 HP with bronze impeller, directly coupled with motor, suitable for minimum total head 20 meter and discharge min 36 M3/HR confirming to relevant IS suitable for AC 3 Phase, Voltage range 300 V - 440 V, 50 Hz. The motor casing shall be of stainless steel, pump shaft / motor shaft shall be of stainless steel, pump bowls shall be of high graded cast iron with & including fully automatic Star-Delta starter of rated capacity matching with the pump set, suitable size submersible (water proof) copper cable from existing electric control/panel to starter & starter to pump set with suitables lugs etc. including connecting the pump set with existing suction & delivery pipe lines with required addition/alteration (if any), nuts, bolts, washers etc. complete all as specified & as directed by the Engr-in-Charge. Make of Pump Set - KIRLOSKAR/KSB/CG/JYOTI, Make of Starter - L&T/C&S/SIEMENS, Make of Cable - HAVELLS/POLYCAB/FINOLEX.

Supply, install, commissioning and testing of multi stage submersible pump set of capacity not less than 15 HP with bronze impeller, directly coupled with motor, suitable for minimum total head 40 meter and discharge min 90 M3/HR confirming to relevant IS suitable for AC 3 Phase, Voltage range 300 V - 440 V, 50 Hz. The motor casing shall be of stainless steel, pump shaft / motor shaft shall be of stainless steel, pump bowls shall be of high graded cast iron with & including fully automatic Star-Delta starter of rated capacity matching with the pump set, suitable size submersible (water proof) copper cable from existing electric control/panel to starter & starter to pump set with suitables lugs etc. including connecting the pump set with existing suction & delivery pipe lines with required addition/alteration (if any), nuts, bolts, washers etc. complete all as specified & as directed by the Engr-in-Charge. Make of Pump Set - KIRLOSKAR/KSB/CG/JYOTI, Make of Starter - L&T/C&S/SIEMENS, Make of Cable - HAVELLS/POLYCAB/FINOLEX.

Supply, install, commissioning and testing of multi stage open-well type submersible pump set of capacity not less than 40 HP with bronze impeller, directly coupled with motor, suitable for minimum total head 180 meter and discharge min 65 M3/HR confirming to relevant IS suitable for AC 3 Phase, Voltage range 300 V - 440 V, 50 Hz. The motor casing shall be of stainless steel, pump shaft / motor shaft shall be of stainless steel, pump bowls shall be of high graded cast iron with & including fully automatic Star-Delta starter of rated capacity matching with the pump set, suitable size submersible (water proof) copper cable from existing electric control/panel to starter & starter to pump set with suitables lugs etc. including connecting the pump set with existing suction & delivery pipe lines with required addition/alteration (if any), nuts, bolts, washers etc. complete all as specified & as directed by the Engr-in-Charge. Make of Pump Set - KIRLOSKAR/KSB/CG/JYOTI, Make of Starter - L&T/C&S/SIEMENS, Make of Cable - HAVELLS/POLYCAB/FINOLEX.

Supply, install, commissioning and testing of horizontal end suction centrifugal pump set, multi-stage of capacity not less than 60 HP, suitable for minimum total head of 180 meter & discharge minimum 65 M3/HR confirming to relevant IS with CI casing, bronze impeller and stainless steel shaft mounted on heavy duty bearings for continuous operation with non-over loading power characteristics for frequent start/stop operations coupled with TEFC electric motor suitable for AC 3 Phase, Voltage range 300 V - 440 V, 50 Hz complete including suitable common steel frame/base plate, MS coupling guard, PCC platform / foundation (PCC 1:2:4, Type B1) as per manufacturer instructions/recommendations etc. with & including fully automatic Star-Delta starter of rated capacity matching with the pump set, suitable size copper cable from existing electric control/panel to starter & starter to pump set with suitables lugs etc. including connecting the pump set with existing suction & delivery pipe lines with required addition/alteration (if any), nuts, bolts, washers etc. complete all as specified & as directed by the Engr-in-Charge. Make of Pump Set - KIRLOSKAR/KSB/CG/JYOTI, Make of Starter - L&T/C&S/SIEMENS, Make of Cable - HAVELLS/POLYCAB/FINOLEX.

NOTE for Item Nos 21 to 24 : (i) Design / drawing / BOM / Technical specifications / comparative analysis of the Items is to be got approved from the Engr-in-Charge & GE before placing final order to the manufacturer. (ii) Anything missed out in the technical specifications but technically required for efficient working is deemed to be included in the quoted rates. (iii) Original manufacturer test certificates, product catalogues etc. in respect of the pumping sets is to be submitted to the Engr-in-Charge. (iv) Cost of suitable fixing arrangements etc. as decided by the Engr-In-Charge/GE is deemed to be included in the unit quoted rates.

M & L for earthing complete with galvanized steel earth plate electrode 600 x 600 x 6.3 mm thick buried directly in ground (in vertical position) earth pit not less than 2.25 mtr below normal ground level with the top edge of the earth plate not less than 1.5 mtr (B.G.L.) and connected to galvanized iron earth strip 32 x 6 mm by means of bolts, nuts, check nuts, and washers of galvanized iron including PCC Chamber & cover with suitable handle, including necessary excavation and earth work in any type of soil, 20 mm dia med grade galvanized steel tube for watering with one end fixed with cast iron funnel and wire mesh, 40 mm bore medium grade galvanized steel tubing for drawing earth lead GI strip protection & common salt, charcoal in alternate layers etc. complete all as shown in EP No 3 of SSR Part 1 and testing on completion complete all as specified and as directed. Note: On testing after completion, if the desired earth resistance is not found according to the relevent Indian standards it is to be redone to the entire satisfaction of Engr-in- Charge at no extra cost to the Dept.

Supply, laying, jointing & testing XLPE insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 25 Sq mm 4.0 core in trenches / through GI pipe / fixed along with pole structure etc with all fixing & connecting accessories complete all as specified & as directed. Make :Havells/Finolex/Polycab/Gloster

Supply, laying, jointing & testing XLPE insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 16 Sq mm 4.0 core in trenches / through GI pipe / fixed along with pole structure etc with all fixing & connecting accessories complete all as specified & as directed. Make :Havells/Finolex/Polycab/Gloster

Supply, laying, jointing & testing XLPE insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 Sq mm 2.0 core in trenches / through GI pipe / fixed along with pole structure etc with all fixing & connecting accessories complete all as specified & as directed. Make : Havells/Finolex/Polycab/Gloster.

Supply, install, commissioning & testing of street light panel suitable for 1 phase, 240 volts supply, maximum load 6 KW, digital 24 Hr timer, 63 Amps SPN contactor, 63 Amps SPN MCB rating incl electric connection all as specified and directed for outdoor operation with & including suitable legs made out of angle iron 25 x 25 x3 mm (min size), necessary PCC foundation complete all as specified & as directed by Engr-in-Charge. Make :Havells/Finolex/Polycab/Gloster

Note: (i) Design / drawing / BOM / Technical specifications / comparative analysis of the Items is to be got approved from the Engr-in-Charge & GE before placing final order to the manufacturer whereever techno-commercial equivalency w.r.t. given Cat/Part ref is concerned. (ii) Anything missed out in the technical specifications but technically required for efficient working is deemed to be included in the quoted rates. (iii) Cost of suitable fixing arrangements as decided by the Engr-In-Charge/GE is deemed to be included in the unit quoted rates.

Supply, install, testing & commissioning of LT control panel board "in-door type" of size 1500 mm (height) x 1800 mm (breadth) x 600 mm (depth) (minimum dimensions) factory fabricated CPRI approved (type-tested) with suitable neoprene rubber gasket to make it completely dust & vermin proof & degree of protection not less than IP-43 & general construction confirming to IS-13947, single door, front & back openable. The panel shall be of the type of 2 Incomers with Bus-Coupler system comprising of 06 Sections : (i) Incoming – I, (ii) Incoming – II, (iii) Bus-Coupler Breaker, (iv) Interlock Logic, (v) Outgoing – I, (vi) Outgoing - II. The panel board shall be fabricated out of 2.0 mm thick CRCA sheet duly pre-treated & powder coated, supporting angle iron frame & MC channel base suitable for 3 Ph, 4 wire system 415/440 volts grade incl complete internal wiring with not less than 2.5 sqmm copper wire incl cable glands of suitable sizes incl suitable PCC (1:2:4) type B-1 foundation/plinth, necessary earthwork (if any), Danger Notice Plates etc. complete all as specified & as directed with & incl the following accessories : (MAIN DG/CHANGEOVER PANEL AT SS NO-02)

BUS-BAR & INTERNAL CONNECTIONS :- The bus-bars shall be made up of 04 Nos high grade Aluminium 600 A rated, duly insulated with 1100 V grade standard colour coded PVC sleeves & rigidly mounted on suitable sized "F" class insulators of non-hygroscopic, non-combustible, all internal connections from main bus-bars to switch gears etc.

BUS-COUPLER BREAKER : MCCB 4P (Ics = 100% Icu) with microprocessor release, adjustable short circuit & adjustable overload setting, inbuilt instantaneous protection, inbuilt ground fault protection, adjustable neutral overload protection, variable trip class, front LED indication, panel mounted display for current metering & trip record with & incl UNCO Module for Status Indication & Control through Communication, suitable for isolation, Mechanical/Door Interlock & Pad/Key lock facility, Spreader Terminals, Phase Barriers etc. having breaking capacity 36 KA & of rating 160 to 400 A - 01 Nos. Model – dsine MTX2.0, Cat No : CM93003OOOOAG of Make L&T or techno-commercially equivalent of LEGRAND/SIEMENS. INTERLOCK LOGIC : Electrical & Mechanical Interlocking arrangement with Trip Logic between the Incomer & Bus-Coupler MCCBs to be provided. (a) Under Normal condition, i.e. when supply is available through both the Incomers, Incomers I & II shall be in closed condition & Closing of the Bus-Coupler Breaker shall be prohibited. (b) In case of failure of either of the sources, the Incomer of that source shall trip through Under-Voltage Relay & Bus-Coupler shall be allowed to close. After restoration, the respective Incomers shall be allowed to close only after opening of the Bus-Coupler Breaker. (c) The above Electrical Interlock should be done through Breaker Auxiliary Contact Switch.

OUTGOING - I : (a) MCCB 4P (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting, suitable for isolation, Spreader Terminals, Phase Barriers etc. having breaking capacity 25 KA & of rating 63 to 80 A - 02 Nos. Model – dsine TM, Cat No : CM91712OOJOOG of Make L&T or techno-commercially equivalent of LEGRAND/SIEMENS. b) MCCB 4P (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting, suitable for isolation, having breaking capacity 25 KA & of rating 100 to 125 A - 02 Nos. Model – dsine TM, Cat No : CM90642OOLO of Make L&T or techno-commercially equivalent of LEGRAND/SIEMENS.

OUTGOING - II : (a) MCCB 4P (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting, suitable for isolation, Spreader Terminals, Phase Barriers etc. having breaking capacity 25 KA & of rating 63 to 80 A - 02 Nos. Model – dsine TM, Cat No : CM91712OOJOOG of Make L&T or techno-commercially equivalent of LEGRAND/SIEMENS. (b) MCCB 4P (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting, suitable for isolation, having breaking capacity 25 KA & of rating 100 to 125 A - 02 Nos. Model – dsine TM, Cat No : CM90642OOLO of Make L&T or techno-commercially equivalent of LEGRAND/SIEMENS. NOTE : (a) Design / drawing / BOM / Technical specifications / comparative analysis of the Panel Board/Accessories showing the dimensions is to be obtained from the CPRI type-tested Manufacturer & is to be got approved from the Engr-In-Charge & GE before placing final order to the manufacturer. (b) Anything missed out in the technical specifications but technically required for efficient working is deemed to be included in the quoted rates. (c) CPRI type-test certificates of the Panel Manufacturer is to be submitted to the Engr-In-Charge.

Supply & laying or passing through pipes 11v grade heavy duty cable with PVC insulated standard aluminum conductor served with inner sheathing of PVC tape armoured with galvanized steel wire or tape & overall PVC sheathed of size 10 Sqmm 4 Core in service connections complete all as specified & as directed by Engr-in-Charge. Make: Havells/Finolex/Polycab/Gloster.

P K ENTERPRISES

KRA Engineering and Construction

lakshmibuilders

Sreekrupa Enterprises