IMPROVEMENT TO CERTAIN SMQs AND OMQs IN CAMP AREA AT AF STN AGRA

Amount

Taking down carefully (aluminium/copper) point wiring complete of any type (batten/ surface conduit or concealed) for light point, fan point, bell point socket point or power point complete with all fitting such as switches, sockets pendants, ceiling rose, round block etc complete and making good disturbed surfaces of wall, floor or ceiling with existing specifications complete all as spcified and directed.

Material and labour for point wiring with two runs of FRLS PVC insulated unsheathed electric cable conforming to IS:694,1100 V grade AC,single core having multistranded copper conductor of size 1.5 sqmm nominal cross sectional area for phase & neutral in & including non metallic rigid PVC conduit ISI marked medium grade not less than 20 mm dia with all conduit accessories in concealed wiring system & 1 run of 1.5 sqmm green PVC insulated copper conductor as a earth wire connected to earth dolly by providing lugs including galvanized MS boxes with laminated sheet cover 3.00 mm thick complete for mounting switches ,sockets,fan regulators etc for the following :-

One light /fan/Exhaust fan point point controlled by one switch

One call bell point controlled by bell push

one 3 pin socket outlet, on the same bord socket 5 Amps point.with other switches with cable 1.5 sqmm

one 3 pin socket outlet, for independent socket 5 Amps point.

All as per item No 2 above but complete with 1100volt grade FRLS PVC insulated unsheathed multistranded wire with 2.5 sqmm copper cable through and including concealed PVC conduit medium grade of size not less than 20 mm, etc fixed in wall/ceiling of suitable size and one run of FRLS PVC Insulated wire of 2.5 sqmm copper cable of green colour connected to upto earth dolly earthing for 15 Amps socket outlet independent all as specified and directed.

All as per item No 2 above but complete with two runs of 1100volt grade FRLS PVC insulated wire unsheathed multistranded wire with 4 sqmm copper cable through and including concealed PVC conduit medium grade of size not less than 25 mm, etc fixed in wall/ceiling of suitable size and one run of 4 sqmm copper cable of green colour connected to upto earth dolly earthing, all as specified and directed.

M & L for point wiring FRLS PVC insulated PVC unsheathed electric cable, 1100 V grade AC, single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area for phase & neutral in existing PVC concealed conduit terminated in existing MS pressed steel sunken box with new 3 mm thick bakelite laminated sheet fixed with new cadmium plated screws and washers for mounting switches sockets fan regulators etc, including 1.5 sqmm single core PVC insulated unsheathed multistranded 1100V FRLS PVC Insulated copper conductor as earth continuity conductor connected to common earth dolly complete all as specified and directed.

All as per srl item No 5 above but for call bell point complete all as specified and directed.

All as per srl item No 5 above but for 3 pin 5 amps socket outlet independent board complete all as specified and directed.

All as per srl item No 5 above but for 3 pin 5 amps socket outlet on the same board with other switch complete all as specified and directed.

M & L for point wiring with two runs of FRLS PVC insulated PVC unsheathed electric cable, 1100 V grade AC, single core having multi stranded copper conductor of size 2.5 Sqmm nominal cross sectional area for phase & neutral in existing PVC concealed conduit, including 1 run of 2.5 sqmm single core PVC(green colour) insulated unsheathed multistanded copper conductor FRLS as earth continuity conductor connected to common earth dolly complete all as specified and directed.

All as per srl item No-9 here in above but using 4.00 sqmm 2 run of FRLS PVC insulated unsheathed multi stranded copper conductor with 1 run of 4 sqmm FRLS PVC insulated unsheathed multistranded copper conductor cable as earth lead complete all as spd and directed.

S & F switch piano flush type one way 5 amps SP 240 volts complete all as specified and directed.

S & F bell push flush type 5 amps SP 240 volts complete all as specified and directed.

S & F switch piano flush type one way 15 amps SP 240 volts complete all as specified and directed.

S & F socket outlet 2 in 1, 3 pin/5 pin 5 amps flush type 240 volts complete all as specified and directed.

S & F socket outlet 2 in 1, 6 pin, 5 and 15 amps flush type 230 volts complete all as specified and directed.

S & F Bell AC , 230 VOLTS, single pole ding dong type complete all as specified and directed.

S & F lamp holder/batten holder/angle holder insulated body with poly carbonate back plate suitable for fittings complete all as specified and directed.

S & F ceiling rose polycarbonate insulated body three terminals complete all as specified and directed.

S & F ceiling fan regulator electronic stepped type 5 stage speed variation ISI marked complete all as specified and directed.

S & F wall/surface mounted type LED light fitiing complete with LED lamp of 1x20 watt (4 Feet) LED batten, extruded aluminium heat sink provided for efficient heat dissipatin & integrated electronic driver complete with all accessories internally pre-wired and including connecting up with three core twisted flexible copper cable complete all as spd and directed. Make:-Havells Cat Part NO. ENDURALINERNEOBS20WLED865PCWH, Crompton Cat Part No. CCS-100-20-65-HL2-DP-NWH, Bajaj Cat Part No. BCLAB20W

M & L tube light fitting with energy saving decorative batten type 9/10 watt energy efficient tube light fitting (2 Feet) highly durable surface mounted LED batten constructed of aluminium/plastic and decorative end caps with all accessories prewired and making connection with 3 core copper flexible cable of size 23/.0076 from ceilling rose/PVC connector to light fittings. Make:- Havells Cat Part No. LUMILINEPLUSBS10WLED86 5SPCSS/ Crompton Cat Part No. LDL-10-CDL/ Phillips Cat Part No. BN021 LED10S-4000PSUGRSI

S & F energy saving new generation LED 10 Watts, 6000 K, IP -65 bulk head luminarie with diffuser complete including connecting electrically using cord flexible 3 core copper flexible cable of size 23/ .0076 from ceilling rose/ PVC connector to light fittings . Make:- Crompton Cat Ref LBHE-10-CDL, Havells Cat Ref HEXAFTIOWLED857 SSYMBOPC, Bajaj Cat PArt No. BIBWP 10W LED.

S & F 20 watt LED building security light made up of pressure dia cast aluminium housing with high power LED as lighting source and lens embedded toughened glass having TOP Opening seperate driver compartment with min IP65 protection, connecting the same to electric source with using copper conductor 23/0.0076 insulated flexible 3 core cable complete all as specified and directed. Make: (i) Phillips Cat Part No.-BRP022LED20CWMRS1PSUGR (ii) Havells Cat Part No-ENDURAPEARLSL20WLED757SASYTOPCMP (iii) Crompton Cat Part No- LSTS-20-CDL-M

Supply & Fixing in replacement light grade GI pipe bracket bend to shape 1.5 mtr (40 mm dia with two pairs of clamps) made out of 40x3mm flat and two nos. bolts & washer with nuts duly grouted iin wall or fixing on pole complete all as specified and directed at site.

M & L for taking down carefully existing serviceable Tube light / bulk head fitting any type/ wattage for re-use/ refixing at same position or any other location after making connection with 3 core copper flexible cable of size 23/.0076 from ceilling rose/PVC connector to light fittings complete all as specified and directed at site.

Taking down ceiling fan, ceiling cable and dismantling blades and removing fan and blades & refixing ceiling fan of any make any sweep keeping aside in store yard in safe custody for painting of ceiling fan complete in situ with synthetic enamel paint by spraying including filling cavities with fillet one coat after cleaning all dust and reassembling the fan including writing MES NO at the site, all as specified and directed.

M & L for providing/ cutting the round/ square hole of required size in wall finishing the same for distrubed surfaces complete all as specified and supply and fixing ventilating fan AC single phase 230 Volt 50 Hz of size 230mm sweep, pvc body with louvers and connecting the same to electric source with using copper conductor 23/0.0076 PVC insulated flexible 3 core cable complete including writing MES No. at the site all as specified and directed. Make:- Orient/ Havells/Crompton/ Plaza.

M & L for providing/ cutting the round/ square hole of required size in wall finishing the same for distrubed surfaces complete all as specified and supply and fixing Exhaust fan of 300 mm sweep, metal body single phase 230 Volt AC including mounting frame, nut, bolts, washers, fasteners etc and connecting exhaust fan to ceiling rose including provn of 3 core flexible copper cable of size 1.5mm not less than 0.5mtr long for connection complete all as specified and directed. Make :- Model Powerflow in Orient, Max air in Bajaj, Aeroclean in Usha.

S & F in replacament of existing unsv sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 12 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.

S & F MCB 'C' series SP 06 to 32 Amp, 230 volts, 50 Hz, Breaking Capacity 10 KA complete all as specified and directed.

S & F MCB 'C' series 32-40 Amp Double pole MCB,complete all as specified and directed.

M & L for replacement of existing unsv submain wiring with two single core FRLS PVC insulated flexible copper conductor cable of size 6 sqmm and one single core FRLS PVC insulated flexible copper conductor cable green colour of size 6 Sqmm as earth lead in & including concealed PVC conduit medium grade, cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specificationcomplete all as specified and directed.

M & L for replacement of existing unsv submain wiring with two single core FRLS PVC insulated flexible copper conductor cable of size 4 sqmm and one single core FRLS PVC insulated flexible copper conductor cable green colour of size 4 Sqmm as earth lead in & including concealed PVC conduit medium grade cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification complete all as specified and directed.

M & L earthing complete with galvanised steel earth plate electrode , 600 x600 x 6mm thick burried directly in the ground (earth pit not less than 2.25 mtr deep below ground level)with top edge of the plate not less than 1.5mtr below ground level connected to galvanised iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI and steel earth wire protected by provison of GI medium grade pipe 15 mm bore including provision of concrete pit made with 40mm thick cover of RCC 1:2:4 reinforced with 6mm dia M.S. round bar placed 75mm c/c and handle of 10mm dia MS bar made to shape, GI medium grade 20mm bore pipe for watering perforated at bottom, 1.75 meter long placed on top edge of earth plate, common salt & charcoal filling, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding 50 mtr all as per electrical plate No-3 of SSR 2009 Part-I and connecting to earth test points all as specified and directed including testing on completion.

S & F LED Lamp 14 watt B22 base, 6500 K, 230 volts complete all as specified and directed. Make: Philips/Havells/Wipro.

S & F LED Lamp 7 watt B22 base, 6500 K, 230 volts complete all as specified and directed. Make: Philips/Havells/Wipro.

S & F in replacament of existing unsv sheet metal enclosures distribution boards, double door three phase 415 volts 4 ways vertical TPN DB for comprising three phase four wire copper strip bus bar of appropriate capacity complete all as specified and directed and comprising of the following (a) MCCB TPN 63 AMPS AC 415 VOLTS, 16 KA =01 NO as incoming and 12 nos. MCB SP 06-32 Amps, C series Note :- (i)The DB shall be VTPN series of Schenieder or equivalent to Legand/ Seimens . (ii) The DB shall be flush fixed ,and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost. (iii) connection of theMCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble -properly crimped. (iv) all the vacant holes of the DB shall be provided with blank plates of appropriate size. (v) double continuous earth wire shall be provided for each three phase DB from earthing mains dolly.

S & F in replacement of MCB 415 Volts, 50 Hz, 63 Amps TPN with rupturing capacity 10 KA including providing thimbles for out-going cables. Make:- INDOASIAN Cat Part No. 8536/ Legrand Cat Part No. 4086 83/ C&S Cat Part No-CSMBS3C63N

M & L for replacement of existing unsv meter box with polystyrene-polycarbonate hinged door, with transparent lid, meter box of size 168 x 253 x 115 mm in accordance with IEC 60670-24, should be IP65 protection with IEC 60529, corrosion proof, suitable for single phase energy meter, internally embedded polyurethane gasket for lid, metric size knock outs for cable entry from top and bottom. Meter box should be able to adpt any make of meter complete all as specified and directed. Make :- Hensal KG 9002/ GEWIS/ RITTAL/SPLSBERG.

M & L for taking down existing serviceable SPN/ TPN DB including all accessories I,e MCBs, SP/ SPN/ TPN etc after disconnecting all electric connections kept in store for reuse at same or other location flush fixed complete all as spd including providing thimbles for out-going cables.

M & L for taking down existing meters carefully and depositing to MES store yard or safe custody for reuse/refixing including making all electric connections after necessary repair work carried out including refixing of old serviceablemeters alongwith mentioned below or all as directed. Note:- (i) Minimum 4 sqmm single core FRLS PVC insulated multi-stranded copper conductor cable shall be used for making connections from Meter to DB including providing pin/ bottle type copper thimles . (ii) All wires shall be drawn in PVC flexible conduit of suitable dia. (iii) Cost of materials and labour for inter connector between meters and DB's are deemed to be included in the unit rate quoted. No extra payment shall be allowed for the same.

S & Fmodular PVC enclosure with plug and socket with a two pin and earth plug and socket, 240V, AC complete with one single pole MCB of capacity 20 Amp 'C' Series, 240V complete all as specified and directed by Engr-in-Charge.make: L&T/Legrand/Schneider/Siemens

Taking out XLPE insulated, armoured heavy duty electric cable 1100 volt grade with aluminium conductor of crosssectional area 10 Sqmm 2 Core/16 Sqmm 4 core/25Sqmm 4core complete all as specified and directed.

Supply & laying in replacement of existing un-serviceable XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volt grade of crosssectional area 10 Sqmm, 2 Core complete all as spd and directed.

Supply & laying in replacement of existing un-serviceable XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volt grade of crosssectional area 16 Sqmm, 2 Core complete all as spd and directed.

Supply & laying in replacement of existing un-serviceable XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volt grade of crosssectional area 16 Sqmm, 4 Core complete all as spcified and directed.

Supply & laying in replacement of existing un-serviceable XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volt grade of crosssectional area 25 Sqmm, 4 Core complete all as specified and directed.

Excavation in trenches, n.exc 1.5m wide and n. exc 1.5m depth for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, laying of cable/pipe lines, etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed

Returning & filling including spreading, leveling watering and well ramming in layers n. exc 25 cm thick in soft/loose soil complete all as spcified and directed.

Removal of excavated soil to a distance n. exc 50 m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed by Engr-in-Charge.

Supply and laying bricks(old size) for cable protection by using common burnt clay building bricks, sub-class 'B' designation 75 laid dry flat across length of the cable with width of the trnches equal to length of bricks complete all as specified and directed.

Supply and laying sand for cuishioning of cable in trenches 8cm below the cable and 15cm above cable for cable protection including spreading, levelling and punning down to 18cm complete all as specified in SSR part-I and as directed by Engr-in-Charge. Note:- Thickness of sand cuishioning shall be measured after punning and consolisdation of sand.

Supply and fixing of GI tubing light grade of 50 mm dia for protection of cable on pole/wall/floor/road crossing wall etc complete all as required at site and as directed.

Supply and fixing of GI tubing light grade of 40 mm dia for protection of cable on pole/wall/floor/road crossing wall etc complete all as required at site and as directed.

Taking up or down GI tubing with all fittings of size 50mm bore complete all as specified and directed.(Necessary earthwork will be measured and paid seperately)

All as per srl No:- 55 above but of size 40 mm bore complete all as specified and directed

All as per srl No:- 55 above but of size 25 mm bore complete all as specified and directed

All as per srl No:- 55 above but of size 20 mm bore complete all as specified and directed

Laying and refixing only old but serviceable GI tubing 50 mm bore obtained from srl Item 55 after necessary cleaning including provision of new fittings, complete all as specified and directed.

All as per srl No:- 59 but obtained from srl item No.56 here-in-before but of size 40 mm bore complete all as specified and directed.

All as per srl No:- 59 but obtained from srl item No.57 here-in-before but of size 25 mm bore complete all as specified and directed.

All as per srl No:- 59 but obtained from srl item No. 58 here-in-before but of size 20 mm bore complete all as specified and directed.

Supply, fixing and laying GI water tubing 50 mm bore medium grade ISI marked with all required fittings such as bends, elbow, tees, short pieces, connector, check nuts and threading complete all as specified and required at site.

All as per srl No:- 63 here-in-before but of size 40 mm bore complete all as specified and directed

All as per srl No:- 63 above here-in-before but of size 25 mm bore complete all as specified and directed

All as per srl No:- 63 above here-in-before but of size 20 mm bore complete all as specified and directed

M & L for replacement of existing unsv Gun metal gate valve ISI marked with iron wheet head screwed both ends for pipe of 50 mm bore complete all as specified and directed.

M & L for replacement of existing unsv Gun metal gate valve ISI marked with iron wheet head screwed both ends for pipe of 40 mm bore complete all as specified and directed.

M & L for replacement of existing unsv Gun metal gate valve ISI marked with iron wheet head screwed both ends for pipe of 25 mm bore complete all as specified and directed.

M & L for replacement of existing unsv Gun metal gate valve ISI marked with iron wheet head screwed both ends for pipe of 20 mm bore complete all as specified and directed.

M&L for LT PVC insulated armoured heavy duty cable end terminal joints heat shrinkable type along pole/DB etc, suitable for aluminium conductor cable and testing after jointing for 25-50 sqmm 3.5 core cable. Make-Denson/Raychem/Birla 3M

All as per item no.-71 above but 10-16 Sqmm 2 core

Demolition of brick work or stone masonry built in cement mortar including all quoins arches pillars etc excl ashlar facing dressed stone work and pre-cast concrete articles complete all as specified and directed.

M&L for brick work with sub class ‘B’ brick straight or curved on plan exc 6 M means radius built in CM (1:6) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing, serviceable tiles to store and rubbish off the premises all as specified and directed.

Taking down cement plaster on brick wall including raking out joints, hacking for key, scrrubing down with water etc all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and directed.

S&F Coloured Non Skid ceramic tiles 7 to 8mm thick joint less (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed in CM(1:6) with provision of any dark color border complete all as specified and directed.

M&L for glazed ceramic designed coloured tiles size 450x350x7 mm thick/350x250x7 mm thick on vertical surface such as dado/skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match with coloured over and including rendering 10mm thick on fair faces of brick work or concrete surfaces in CM (1:4) complete all as specified and directed.

M & L for vitrified colour tiles of 8 to 10mm thick first quality (square / rectangular) polished, area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm as in floor etc set and jointed in neat cement slurry and pointed with coloured cement to match the colour of tiles over and including 15mm thick screed bed in CM 1:6. Note:- Rates also includes in this item for necessary raking,circular cutting or notching and waste on tiles with provision of any dark color border complete all as spcified and directed.

-Ditto- all as per Item No 80 above but as in skirting including 10 mm thick rendering in CM 1:4 complete all as specified and directed.

M & L for Machine cut kota stone (size 550x550mm) slab flooring 18-20mm thick over and including 15 mm thick cement screed base in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to obtain mirror finish complete all as spcified and directed. Note:- Rates also includes in this item for necessary raking,circular cutting or notching and wastes

M&L Kota stone slab 10-12mm thick in riser of steps, skirting, dado & pillar over and including 10mm thick plaster in CM (1:4) & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing to obtain mirror finish complete all as specified and directed.

S&F Coloured Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed in CM(1:6) complete all as spcified and directed.

M&L for coloured ceramic tiles size 200x300x7 mm thick on vertical surface over and including 10mm thick rendering in CM (1:4) such as dado/skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match with coloured complete all as spcified and directed.

M&L for rendering 15 mm thick on fair faces of brick work with mixing liquid water proofing compound as per manufacturer's instructions, the surface finished even & fair in CM 1:4 without using extra cement complete all as specified and directed. (WPC will be measured and paid separately)

M&L for 15mm thick cement plaster in CM (1:6) on other than fair faces of brick work finished even and smooth without using extra complete all as spcified and directed.

M&L for preparation of newly plastered wall surfaces & applying two coats of cement base paint on walls over one coat of primer complete all as spcified and directed.

M&L for rendering 5 mm thick on fair faces of brick work or concrete surface of ceiling in cement mortar 1:3 finished even & smooth (without using extra cement) complete all as specified and directed

M&L for scraping out loose motar/concrete by chiseling/ wire brughing complete and applying rust removing solution (rebaklene soulution) to exposed corroded reinforcement and applying a coat of epoxy primer (Nitozink primer from M/S Fosroc or equivalent as approved by GE) as per manufacture instructions providing and fixing of wire mesh of weight 2.5 Kg per Sqm and apply 25mm average thickness in CM (1:4) mixed with liquid integral water proofing compound (complast 'X' recommended by the manufacture with gunitting machine at a pressure not less than 5Kg/Sqcm finally rendering 10mm thick plaster in CM (1:4) using liquid integral water proofing compound (complast 'X' 421 i.e. from M/S Fosroc and nitobound AR from M/S Fosroc or equivalent as approved by GE) in the proportion recommended by the manfacture complete all as specifed and directed.

M&L for dirilling hole in RCC structure by drilling machine upto a depth of 50mm and 18mm dia, removing dust etc by vacuum cleaner and blower, provindg and fixing of heavy grade GI pipe nipple 15mm dia, 80mm long on the concrete column, beams, slab, floors etc 1.2 metre centre to centre in both direction and injection of cement slurry mixed with liquid integral water proofing compound (Conplast x 421 and Nitobond AR manfacture by M/S Fosroc chemical India or equivalent chemeical of M/S Pidilite Insustries as per manufacture instruction of appropriate consistency and conbex 100 of M/S Fosroc or equivalent chemeical of M/S Pidilte @ 225 gm per bag of cement through nipple and close the ends of nipples with epoxy putty/silca jally after injecting the chemical mixed with cement slurry completed all as specified and directed.

Supplying only Integral waterproofing compound liquid as per manufacturer instruction.

Demolation of RCC chajjas, slab, beam and similar work as specified and directed.

Use & Waste Formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. Rough finished surfaces of concrete flat, all as specified and directed.

Use & Waste Formwork to chullah hoods, chajjas, troughs & similar items including edges Fair finished surfaces of concrete flat, all as specified and directed.

M&L TMT bar 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality conforming to GD-I. IS-432 (Part I) ,all as specified and directed.

All as per item no. 96 above but 6 to 8mm dia complete all as specified and directed

All as per item no. 96 above but 5 to 10mm dia as in stirrups, spacers or binders complete all as specified and directed.

M&L RCC 1:2:4 type B1 using 20mm graded stone aggregate as in chajjas complete all as specified and directed.

M&L RCC 1:2:4 type B1 using 20mm graded stone aggregate as in beams,lintels complete all as specified and directed

Dismantaling brick tiles laid bedded and pointed in cement mortar on roof of any size and any description complete all as specified and directed.

Taking down existing roof treatment any thickness including plastering, leaping plaster of any thickness cuting & up rooting tree roots/Vegitation growth & removing the debris from the premises upto 500m from the MOD land including cleaning/washing down and keeping surfaces clean complete all as specified and as directed.

M & L for 10 mm thick screed bed in cement mortar 1:4 complete mixed with liquid water proofing compound as per manufacturers instructions (note:Water proofing compound shall be measured and paid seprerately under respective item) over roof top surface finished even and smooth using extra cement and application of water proofing treatment using APP modified roof membrane over existing accessible RCC roof slab / chajja / canopy / parapet wall to be executed through approved applicator of the membrane manufacturer with following specification etc complete all as specified and directed :- (a) Cleaning existing surface properly. (b) Applying one coat of hot blown bitumen grade 85/25 conforming to IS 702 @1.2 Kg per Sqm over oil bound bitumen primer @ 0.40 litre / Sqm manufactured by the same agency as that of APP membrane with a density 0.87-0.89 Kg per litre at 25 degree centigrade on prepared surface. (c) Laying not less than 4mm thick APP modified water proofing membrane weighing not less than 3.60 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gms/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. Physical property of membrane shall be as under :- (i) Membrane weight not less than 3.60 Kg/Sqm. (ii) Non woven polyester weight not less than 160 gms/Sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650/Sqcm and transverse not less than 450/sqcm at 230 degree Celsius. (v) Tear strength - longitudinal not less than 300 N & transverse not less than 250N. (vi) Elongation of reinforcement not less than 30%. (vii) Impermeability under water pressure not less than 3 Kg/Sqcm. (d) APP membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap. (Note:- WPC shall be measured and paid separately)

M&L for lying 40mm thick brick tiles over and including bedding layer 20mm screed in CM 1:4. The cement mortar screed shall be mixed with liquid water proofing compound as per manufacturer's specfication/instructions and tiles joints shall be filled with 1:3 CM mixed with crude oil as per SSR-2009 (Part-I).

Cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings and making good cutting exc 10cm and not exc 20cm girth for brick wall surfaces complete all as specified and directed

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and directed.

M&L for 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like bedded over and including 15mm thick screed bed in CM (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for 20cm X 20cm X 20mm thick PCC tiles, machine pressed factory made as per IS-1237-1980 (ISI marked) laid over and including 20mm thick screed bedding in CM (1:4) mixed with liquid water proofing compound as per manufacturer's specifications/instructions and tiles joints shall be filled with 1:3 CM mixed with crude oil as per SSR-2009 (Part-I) and dismantling of tiles complete all as specified and directed.

M&L Providing cement concrete type B0 (1:2;4)using 12.5mm graded stone aggregate as in coving on chajja, balcony or in roof kerbs, pressed chowkhat, rounded or chamfered on edges and similar work complete all as specified.

Disconnecting existing water tanks of capacity exceeding 500 litres but not exceeding 1000 litres, setting aside (or lowering if required) for repairs , refixed & reconnected in position after cleaning etc to be measured separately) complete all as specified and directed.

Demolition of PCC in ground floors & pavings n exc 15 cm thickness (below or above ground level) (unreinforced) and removal of demolition materials to outside MoD land complete all as specified and directed.

M&L for 75mm thick cement concrete type C-1 (1:3:6) (using 20 mm graded stone aggregate ) as in plinth protection and path finished even and fair without using extra cement including provision of 20mm wide construction joints at every 3m interval and at every change of direction and construction joints shall be filled with sealing compound Grade-A complete all as specified and directed by Engineer-in-Charge.

Demolition of unreinforced cement concrete of any description & in any portion not otherwise specifically provided for & removal of demolition material to out side MOD land complete all as spiecified and directed.

M&L for PCC (1:2:4) type B-O (using 12.5mm graded aggregate stone aggregate) as in padding on roof for correction of slope complete all as specified

M&L for Cement concrete type E-2 1:5:10 (using 40mm thick graded stone aggregates as in foundations, sunken portion filling and mass-concrete complete all as specified and directed.

M&L 25mm thick PCC type B-O, (1:2:4) using 12.5mm graded stone aggregate as in sub base complete all as specified and directed..

M & L for water proofing treatment to sunken roof with APP based polymeric membrane, 3 mm thick (minimum), weighing 3.5 Kg/Sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/sqm) shall be applied over and including applying one coat of hot blown bitumin grade 85/25 confirming to IS- 702 @ 1.2 Kg per Sqm over a coat of bituminous primer @ 0.3 litre per sqm surface, application of APP modified membrane joint shall be by torch application. The overlaps shall be minimum 100 mm on the transverse direction and 75 mm longitudinal direction complete all as specified and directed. Make : (i) SUPER THERMOLAY manufactrued by M/s STP limited. (ii) IWL (HYPERPLAS POLYSTER) manufactured by M/s IWL India Ltd. (iii) Pidilite Industries. (iv) M/S Sikka industries WP Shield

S & F 16 to 18mm thick Dholpur stone cladding gang saw cut with machine cut edges, uniform colour of each stone size exceeding 0.25 sqm and not exceeding 0.5 sqm area fixed with and including one number SS clamps (grade-202) of flat 30mmx 2mm, 150 mm long made to shape in each slab, making V groove at top and bottom of stone and drilling hole for hold fastener, polishing, rubbing complete all as specified and directed.

Taking up or down steel tubing and connections 15mm bore complete all as specified and directed

Taking up or down steel tubing and connections in new or old position for 20mm bore pipes complete all as specified and directed

Fixing only GI tubing and connection in new or old position for 15mm bore pipes complete all as specified and directed.

Fixing only GI tubing and connection in new or old position for 20mm bore pipes complete all as specified and directed.

S&F 15mm bore tubes medium grade galvanized with all fittings and fixed complete to walls ceilings or laid in floors complete all as specified and directed

S&F 20 mm bore tubes medium grade galvanized with all fittings and fixed complete to walls ceilings or laid in floors complete all as specified and directed

Dismantling Asbestos Cement (Corrugated, Semi corrugated etc.) sheets in roof coverings.

M&L for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as spd and directed.

M&L for pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as spd and directed.

Cutting chases, pinning in, brick walls and making good to facing where required and pointing in CM (1:3) to ends or edges and making good cutting not exc 10 cm girth all as specified.

S&F in repair plate rack with racks and guard bars made out of stainless steel minimum 1mm thick, over all size 900mm X 750mm and assembled with using brass nuts, bolts and washers complete all as specified and as directed.

M&L for 32 mm dia low density polyethylene pipes (LDPE) of pressure rating 6Kgf/cm2 fixed to wall or floor complete all as specified and directed.

S&F in repair PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets flush pipe of polyethylene of low or high density of PVC, 32mm dia for low level cistern complete all as specified and directed. .

S&F in repair stainles steel sink with draining board made out of stainless steel 1.00mm thick sheet for kitchen with plugs, washers and waste, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting unions to pipe over all size 915mmx460mm with bowl size 410mmx330mmx160mm including waste pipe/waste coupling etc all as specified & directed.

S&F in repair PVC 32/40mm dia flexible waste pipe 800mm long with socket fixed with sink/Wash basin waste coupling complete all as specified and directed.

S&F in repair Bip tap 15mm bore standard of PTMT any colour screwed for iron pipe & fixed (min. weight 15mm - 90gms) complete all as specified and directed. Make :-Prayag/Symet

S&F in repair Stop valves 15 mm bore fancy type, CP with long shank & cup (conncelaed type), cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repair 15 mm angle stop value chromium plated fancy type complete all as specified and as directed.

S&F in repairs CP Bib taps 15 mm bore long body, cast copper alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule fancy type complete all as specified and directed.

S & F in repairs vitreous china wash down water closet ( pedestal pattern), white, including PVC seat cover white with hinging device etc complete all as specified.

S&F in repairs Vitreous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern & flush pipe) complete all as specified and directed.

S&F in repair wash hand basin vitreous china wash basin white flat back size 580x400 including supplied and fixed angle iron brakets errecting stand, CP waste coupling, waste pipe complete all as specified.

S&F Waste fittings 32mm bore, brass, CP for glazed ware sinks, basins, etc. with long screwed shanks & fly-nuts, flange end bedded in red lead cement & other end fixed complete all as specified and directed.

S&F Waste fittings 40mm bore, brass, CP for glazed ware sinks, basins, etc. with long screwed shanks & fly-nuts, flange end bedded in red lead cement & other end fixed complete all as specified and directed.

S&F in repair CP Pillar taps fancy type 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F in repair brass chromium plated shower roses with swivel joints 125mm size in square with CP long shank arm including fixing to steel pipe or union complete all as specified and as directed.

S&F in repair Chromium plated Towel rail 600mm long of fixed with & including CP brass screws & wooden/plastic cleats (min. weight 190gms) complete all as specified and directed.

S&F in repair Grating doom 100 mm dia of PTMT (min. weight 25 gms) complete all as specified and directed

S&F in repair Plastic water closet seat, white ISI Marked, closed pattern with flat bottom and cover and mild steel chromium plated hinges device complete all as specified and directed.

S&F in repair PVC health facet suitable for Europian western commode (EWC) including PVC connection 15mm size with PTMT nuts and washer, of length 900mm complete all as specified and directed.

S&F in repair 15 mm CP wash basin mixture fancy type, with capstan heads, chromium plated, screwed down for high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed by Engr-in-Charge. Make : Jaquar/Marc/Plumber

S&F in repair CP wall mixer for mixing Hot & cold water screwed down for iron pipe 15mm bore complete all as specified and directed. Make : Jaquar/Marc/Plumber

S&F in repair Soap dish, Vitreous China white, approximate size 160x160x90mm complete all as specified and directed.

S&F in repair Towel Ring of PTMT fixed with & including CP brass screws & wooden/plastic cleats (min. weight 90 gms) complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 500 Ltrs Capacity with 20mm dia PTMT float valve incl Dismantling water tanks & removing to store complete all as specified and directed.

S&F Rotational moulded polyethylene triple layered water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 1000 Ltrs Capacity incl with 20mm dia PTMT float valve & Dismantling water tanks & removing to store complete all as specified and directed.

S&F in repair 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe (minimum weight 210 gms) complete all as specified and directed.

S&F in repair Gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and directed.

S&F Mild Steel 300mm, ordinary rat tail rod patttern springs including roller & roller plate complete all as specified and directed.

S&F sheet glass corner self of 3 tier assembly consisting of 5.5mm thick sheet glass self 15cm radius with chromium plated bracket guard and rail and fixed with CP screws and wood cleats with wall complete all as specified and directed.

S & F in repair Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm with tinned tacks or galvanised wire staples windows complete all as specified and directed.

S&F drapery rod fancy type, made out of 25mm dia MS pipe having wall thickness 0.63mm bright finish, colour and pattern as approved by GE, over all dia 28-29mm complete all as specified and directed. Make: Aerolux/ MEC/ Vista.

S&F mild steel prepainted brackets suitable to hold the drapery rod/ curtain rod 25mm dia and fixed to wall (concrete/ brick masonary) with the help of 2Nos 50mm long steel screws and rawl plug including drilling with electric drill and making good the disturbed surface complete all as specified and directed. Make: Aerolux/ MEC/ Vista.

S&F plastic finial of 28-29mm bore, decorative type, of best quality to suit the drapery rod/ curtain rod and fixed at the end of curtain rod with suitable adhesive colour and pattern as approved by GE complete all as specified and directed. Make: Aerolux/ MEC/ Vista.

Dismantling of wall and ceiling boards (fibre, pulp, insulation,etc)or insulation boards/slabs/blankets,any thickness, inclduing cover fillets complete all as specified and directed.

M&L for powder coated GI grid false ceiling of grid size 600mm x 600mm with Tee of dimensions web- 25mm, flange-35mm and thickness 0.7mm & wall angles of web and flange size 25mm each and thickness 0.7mm fixed to wall and hanging with roof with 4mm GI suspender including 4 mm thick designer E-board of size 595 mm × 595 mm etc complete all as specified & directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames exc 1.5 sq. m but n exc 4 sq. m each complete all as specified and directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) n. exc 1.5 sqm complete all as specified and directed.

Taking down shutters of any description n exc 1 sqm area each complete all as specified and directed

Taking down shutters of any description exc 1 sqm and not exc 2 sqm each complete all as specified and directed

Taking down shutters of any description exc 1.00 Sqm mtr and n:exc 2 Sqm in each including resecuring or easing and adusting etc and refixing in same opening complete all as specified.

S&F solid PVC door frame of size 50x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in door opening as per specification and drawings complete all as specified and directed.

S & F with wood free EPS Factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front Face & 2mm Plan colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed

S&F 18mm thick Rajashri UPVC ply of grade 1 quality of both side plain white colour fixed with screwes, solvent cement/ adhesive to make kitchen cabinate sides top and botton, shelves inside the cabinet and shutter or drawer complete all as specified and directed.

S&F 18mm thick Rajashri UPVC ply of grade 1 quality of both side pre laminated colour fixed with screwes, solvent cement/adhesive to make kitchen cabinet and cupboard sides top and bottom, shelves inside the cabinet and shutter or drawer complete all as specified and directed.

S&F 6mm thick Rajshri UPVC ply of grade 1 quality of both side plain white colour fixed with screwes solvent cement/ adhesive to make kitchen cabinet and bed room cupboard back side complete all as specified and directed.

S&F Stainless steel handle of 100mm size for kitchen cabinet and bed room cupboard shutter complete all as specified and directed.

S&F Stainless steel hinges of 100mm size complete all as specified and directed.

S&F Stainless steel tower bolt of 100mm size complete all as specified and directed.

S&F MS hold fast and similar article conforming to Fe-290 Gde-E-165-0 or Fe-310-o complete all as specified and directed.

M&L for PCC (1:3:6) type C-1 with using 20mm graded stone aggregated as in cill, step and for inserting hold fast of doors and windows complete all as specified and directed.

S&F aluminum anodized barrel tower bolt of extruded section size of bolt 150mm complete all as specified and directed.

S&F aluminum handle cast type anodized 150 mm size complete all as specified and directed.

S&F Butt hinges 100mm size, medium weight, cold rolled mild steel.

S & F 75 mm long Extruded Aluminium alloy handles, fabricated type, anodised.

S & F 75 mm long medium weight, cold rolled mild steel Butt hinges.

S&F for 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S & F Mild steel work in window guard bars, plain, let in and fixed independently in wooden frames, hand rail,balusters and similar work confirming to Fe 410 - O or Fe 310 - O complete all as specified and directed

S & F Aluminium plate type II Gate and shutter, hook & eye 150 mm size complete all as specified and directed

S&F Stainless steel hasp & staple for 75mm size size for kitchen cabinet/ bed room cupboard shutter complete all as specified.

S&F auto closing hinges 35mm of O crank (KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutter complete all as specified and directed.

Preparing surfaces of wood and wood based materials, treating ends of posts, backs of chowkhats, etc, area tarred exc 0.1 sqm but n,exc 0.5 sqm each complete all as specified and directed.

Resecuring or easing adjusting exc 1.5 sqm but n excc 2 sqm easing/cutting of doors shutter from bottom without taking out from the chowkhats all as specified and directed by Engr-in-Charge.

M&L Preparing surface of wood & wood based materials, steel & iron work, new or old, & treated with tar or coal tar black paint, area n exc 0.1 sq. m each, treating small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats, etc complete all as specified and directed.

S & F Second class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F 30mm thick flush shutters factory made solid core construction with block boards core and plywood face panels, commercial type on both sides (ISI marked) fixed to chowkhats complete all as specified and directed.

S&F 35 mm thick flush shutters factory made solid core construction with block boards core and plywood face panels, commercial type on both sides (ISI marked) fixed to chowkhats complete all as specified and directed.

S&F 35mm th 2nd class Hard wood (Hollock) Kiln seasoned and chemically pressure treated glazed & skeleton shutters, open rebated at prepared to receive glass/gauze (without sash bars) edges of framing plain, chamfered, or rounded, fitted with and incl cut and mitred beads for securing glass, gauge etc, size of members of shutters as specified in SSR Pt-I, Sec-8, clause 8.24 (a) fixed to chowkhats complete all as specified and directed.

S & F factory made box type steel window/ventilator with pressed steel frame made out from 1.25mm thick steel having two rebete with glazed shutters and fly proofing shutters including guard bars etc complete all as specified & shown in drg CE/ALD/TD-172 sh 1/2 & 2/2 complete all as specified and directed.

S&F IInd class hard wood Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours; articles n exc 200 cu. cm each complete all as specified and directed.

S & F 50 mm long medium weight, cold rolled mild steel Butt hinges.

S&F factory made plain framed, panelled shutter 35mm thick (two panel) with lock rail & panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. 2nd Class HW rail & style of size as per IS: 1003 (Part I), kiln seasoned & chemically pressure treated complete all as specified and directed.

S&F 30mm thick factory made 2nd class Hard wood (Hollock) Kiln seasoned and chemically pressure treated glazed & skeleton shutters, open rebated at prepared to receive glass/gauze (without sash bars) edges of framing plain, chamfered, or rounded, fitted with and incl cut and mitred beads for securing glass, gauge etc, size of members of shutters as specified in SSR Pt-I, Sec-8, clause 8.24 (a) fixed to chowkhats complete all as specified and directed.

S&F 30mm th 2nd class Hard wood (Hollock) Kiln seasoned and chemically pressure treated glazed & skeleton shutters, open rebated at prepared to receive glass/gauze (with any number of sash bars) edges of framing plain, chamfered, or rounded, fitted with and incl cut and mitred beads for securing glass, gauge etc, size of members of shutters as specified in SSR Pt-I, Sec-8, clause 8.24 (a) fixed to chowkhats complete all as specified and directed.

M & L for Applying two coat of synthetic enamel paints over one coat of pink primer on wooden surfaces over 10 cm width or girth including preparation new surfaces complete all as specified and directed.

M&L two coats of synthetic enamel paint to steel surfaces of any description,over 10cm in width or girth, not otherwise described over one coat of red oxide primer including preparation of surfaces complete all as specified and directed.

Hacking out old broken glass any thickness size, quality or description from wooden frame glazed with putty or fixed with beads complete all as specified and directed.

Supply and fixing wire cloth 0.56mm nominal dia of wire and avg width of aperture 1.18mm complete all as specified and directed.

Supply and fixing 3mm thick sheet glass ordinary quality and glazing with oil putty or beads in square not exc 0.50 sqm in each pane, complete all as specified and directed.

S&F Figured glass 3.0mm thick, pin head type & glazing with oil putty in squares n exc 0.5 sq.m in each pane complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F angle iron posts and rails,drilled and struts in fencing including cutting tops to shape as directed, driiling holes, notching for wire, etc, flat iron fillets (for secruing wire mesh,concertina coil,barbed wire etc) including all necessary drilling, bolting or riveting, etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

S&F Rolled mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with & including either hooks & hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails & guides) & hanging; also fastening & fixing complete GDE Fe410-0 or Fe 310-O

S & F Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

S& F in repair 1mm thick mild steel, plain black sheet in in hearths; covering to door shutters; covering to door chowkats (frames); chullah hoods; waters tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size, edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40mm lap joints or welded/riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc.complete all as specified and directed

S & F Floor door stopper of Aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate 150 mm.

Taking down eaves gutters and rain water pipe (any size or pattern ) including all fittings , heads, shoes, bends, swan-necks etc. complete all as specified and directed.

S&F PVC SWR pipes 110mm bore single socketed in any length with rubber ring joints fixed to wall complete all as spd and directed.

S & F PVC SWR pipes 75mm bore single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S & F PVC SWR pipes 75mm bore single socketed in any length with rubber ring joints, laid in trenches or in floor complete all as specified and directed.

S&F in repair PVC (SWR), junction single, (Single T) equal or unequal 110mm dia complete all as spcified and directed.

S&F in repair PVC (SWR) vent cowl 110mm dia complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) bends any radius complete all as specified and directed

S&F in repair 75mm bore PVC (SWR) bends any radius complete all as specified and directed

S&F in repair 75mm bore PVC (SWR) bends any radius with access door complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) bends any radius with access door complete all as specified and directed.

S&F in repair PVC floor trap 125/110mm dia including jointing to waster pipe fixed in cement conccrete type- B1 (1:2:4) complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) branch piece single (Single Y) equal or unequal any radius complete all as specified and directed.

S&F in repair 75mm bore PVC (SWR) branch piece single (Single Y) equal or unequal any radius complete all as specified and directed.

S&F in repair 75 mm bore PVC (SWR) single (Single T) equal or unequal any radius complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) single (Single T) equal or unequal any radius complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) vent cowl any radius complete all as spcified and directed.

S&F in repair 75mm bore PVC (SWR) vent cowl any radius complete all as specified and directed.

S&F Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays. Including bolts & nuts & securing ends of stays to wall or roof for 110 mm bore pipe complete all as specified and directed.

M&L for preperation of newly plastered ceiling surface & applying three coat of white wash on ceiling surface complete all as specified and directed.

S&F aluminium beading 50 mm wide fixed with beading on wooden shutters bottam rail with screw all as specificed and directed.

M&L in repair 18/19mm thick Particle board, medium density, flat pressed, single layer type / three layer type with BWR type adhesive,fixed with screws to timber frame work complete all as spcified and directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps (when open) is 30 mm complete all as spcified and directed.

S&F steel tank cover with zink coating, dia of cover 500 mm and height 150mm of cut spherical shape and gas welded of spikes 2mm dia and 50mm length at 50mm c/c both bay in zig zag motion with ms hinges, hasp and staple fixed to existing PVC water water starage tank of any capacity and binded with barbed wire 2mm dia and 2.24mm barbs 75mm c/c all around of tank including dismantling of old pvc water tank cover complete all as specified and as directed.

M&L two coats of distemper oil emulsion on newely plastered wall surfaces including preparation and 3mm thick wall care putty complete all as specified and directed.

M&L for preperation of newly plastered wall surface & applying three coat of white wash on wall surface.Complete all as specified & directed.

M&L for Applying one coats of white wash on old wall surface including preparation of surface complete all as spcified and directed.

M&L for Applying one coats of white wash on old Ceiling surface including preparation of surface complete all as spcified and directed.

M&L for complete removal of existing treatment of old decorated furface of walls and applying two coats of cement base paint complete over a ccoat of alkali resistant primer complete all as spcified and directed.

M & L complete removal of existing treatment of old decorated surface of walls and applying two coats of oil bound distemper with 3 mm thick wall care putty to make smooth surface all as specified and directed by Engr-in- charge.

M&L for one coat of synthetic enamel paint on old wood or wooden based surfaces of any description over 10cm width or girth including preparation surfaces complete all as specified and directed.

M&L for one coat of synthetic enamel paint on old steel surfaces of any description over 10cm width or girth including preparation of old painted steel surfaces complete all as specified and directed.

S&F coloured Toilet paper holder, vitreous china box type complete all as specified and directed.

Providng and injecting chemical emulsion for post construction anti termite treatment along the external wall below concrete or masonery apron using chemical emulsion @ 2.25 Ltr per liner meter inlcuding drillling and pluging holes etc in apron complete all as specified and directed by Engr-in-Charge.

Treatment of soil under existing floors using emulsion @ one litre per litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors complete all as spcified and directed.

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates of Fe 410-W (Gde E-250) quality A complete all as spcified and directed.

M & L 50mm thick sandstone slabs; set and jointed over joists in cement mortar 1:4, etc., complete

S & F Fe 410-W (Gde E-250) quality A, Roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in Soft/loose soil

M & L Type C2 1:3:6 (40 mm graded aggregate) Cement concrete in foundations, filling and mass-concrete

M&L Brickwork with sub-class `B' brick straight or curved on plan to any radius in half brick thick walls built in CM 1:4.

S&F aluminum anodized barrel tower bolt of extruded section size of bolt 100mm

S&F factory made solid panel PVC door shutter 30mm thick (style ) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded colour plain PVC or channel having a PVC sheet strip of 20mm width stuch in side with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert top rail & bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement supplying & fixing in the frame at site as per specification & drawing.

M/L for prepration of newly plastered external surfaces of wall incl cornises plasters and appling two coat of exterior acrylic weather proof anti fungal emulsion paint of approved brand and shade over one coat of alkali primer all as per manufacturs instrustions over a layer of JK/ Birla wall putty 2mm thick including necessary scaffolding etc complete all as specified and directed.

Complete removal of existing treatment and preparation of old surfaces of wall.

M/L for prepration of old/existing external surfaces of wall and appling two coat of exterior acrylic weather proof anti fungal emulsion paint of approved brand and shade over one coat of alkali primer all as per manufacturs instrustions incl over a layer of JK/ Birla wall putty 2mm thick including necessary scaffolding etc complete all as specified and directed.

M&L for Machine pressed precast concrete, rubber moulded coloured interlocking paver block of any shape and size confirmingto IS-15658-2006 of 60mm th M-35 grade with gray cement and pigment complete all as specified.

M & L for sand filling for interlocking tiles including watering and consolidation complete all as spcified and directed.

M&L for 100 mm PCC type D2 1:4:8 (40 mm graded agg) as in sub base complete all as spcified and directed.

M&L plain cement concrete type C-I, 1:3:6 (using 20 mm graded stone aggregate) cast in situ in kerb/edges(in interlocking tile path) like including weathering, slightly rounded or chamfered angles and throating, complete all as spcified and directed..

S&F S.W.G pipe grade A laid in trenches with cement joint, pipe of 150mm dia pipe incl Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed.

M&L PCC (1:4:8) type D2 using 40mm graded stone aggregate as in bedding hanching to side of drain pipe as specified for 150mm dia pipe complete all as spcified and directed.

Cutting into existing M.H for connecting new drains and making good to pipe and rendering cuting benching etc and finished etc complete all as spcified and directed.

Demolition of Reinforced cement Concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as spcified and directed

M&L MS TMT 8mm dia and over cut to length bent to shape required including cranking bending spirally for hoping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for pre-cast RCC (1:2:4) type B-1 (using 20mm graded stone aggregate) cover slabs for man-holes etc set in CM (1:6) complete all as specified and directed.

M&L for Soakage wells exc, in ordinary Soil, Foundation in PCC 1:3:6, wells of Honey combed and solid in M-25 Concrete, including intercepting chamber, screen chamber Brick work in CM, RCC cover slab in M-25/ RR masonry / Filling with brick bats, complete of size 3.6 M dia X 4.5M deep complete all as spcified and directed and shown in drg no.. CELZ/TD/576 sheet 1/2 to 2/2.

M & L for conventional type RCC Septic tanks designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, RCC M-30 Design mix in walls, base slab, baffle walls and roof slab incl beams etc with vent shaft, manhole opening with covers connectionn etc.,complete with effective depth of 1.5 m and overall depth of 3.0 m for 50 users complete all as spcified and directed and shown in drg no. CELZ/TD/217 sheet 1/2 to 2/2

S&F Mild steel posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.

S&F Mild steel round bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending with clips for fencing complete all as spcified and directed.

Supply only Chain link MS galvanisd fencing, 100 x 100

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. ncluding provission of binding wire complete all as spcified and directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm & n. exc 10 cm longcomplete all as spcified and directed.

M&L Preparation of new surface appling two coat of Aluminium paint over one coat of red oxide primer exc 10 cm width or girth complete all as spcified and directed

M&L Preparation of new surface appling two coat of Aluminium paint over one coat of red oxide primer n.exc 10 cm width or girth complete all as spcified and directed.

Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as spcified and directed.

M&L for 15mm thick cement plaster in CM (1:4) on fair faces of brick work finished even and smooth with using extra cement complete all as spcified and directed .

Plain Cement Concrete Type B1 1:2:4 (using 20 mm graded stone aggregate) cast in situ in lintels up to 1.5 M span, cills and other similar bands, plinth courses, parapets, copings, bed plates and the like including weathering, slightly rounded or chamfered angles and throating, complete all as spcified and directed.

S & F Mild steel work in framed and hung gates, including Pintle hinges, stops, hand made sliding bolts etc. and similar work confirming to Fe 410 - O or Fe 310 - O complete all as spcified and directed.

Surface dressing not exc. 15cm deep in soft/loose soil.

Excavating in trenches, n exc. 1.5m wide and n exc. 1.5m depth; for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc. n exc. 10 sqm on plan and n exc 1.5m in depth and getting out in soft/ loose soil complete all as specified and directed.

M&L cement concrete in foundations, fillings and mass- concrete type E2 1:5:10(40mm graded stone aggregate) complete all as specified and directed.

Removing excavated soil material exc 500m but n exc. 1000m and depositing where directed.

Returning , filling in, including spreading, levelling, watering and well raming in layers n exc. 25 cm in soft/loose soil.

M&L for rendering 15mm thick on fair faces of brick work finished even & smooth without using extra cement in CM 1:6 complete all as specified and directed.

Demolition of PCC in ground floors and pavings exc 15cm thickness (below or above ground level)(unreinforced) complete all as specified and directed.

M&L cement concrete in foundation, filling and mass concrete type D-2 1:4:8(40mm graded crush stone aggregate), complete all as specified and directed.

M/S JAWAHAR LAL SHARMA