PROVISION OF RCC CULVERT 8 by 1 MTR NEAR OMQ AREA, PROVISION OF SHED NEAR COOK HOUSE ENTRANCE, ADDN AND ALTN OF BLDG NO P-24 AND PROVISION OF MISC E AND M WORKS AT 2AFSB MYSORE

Amount

Taking down chowkats or frames with shutters ( without taking of shutter from the frame) exc 1.5 sqm but n.exc 4.00 sqm each complete all as directed.

Cutting openings, through brick walls for door, window and other openings or enlarging existing openings built in cement mortar and removing surplus etc. to store and rubbish not exc. 50m etc complete all as specified and directed.

M&L for pre cast cement concrete solid block masonry 1:3:6 type C-1(using 20mm aggregate)with solid block exc 10cm in width setting in CM 1:4 etc complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces with CM 1:6 finished even and smooth without using extra cement in internal surfaces complete all as specified and directed.

M&L for rendering 10 mm thick on ceiling in CM 1:3 even and smooth without using extra cement complete all as specified and directed.

M&L for 10mm thick rendering in CM 1:4 on brick or concrete surfaces finished even and smooth complete all as specified and as directed.

M&L for preparing new plaster surface apply two coat of oil bound distemper over coat of wall care putty to obtained smoothness of wall/ceiling surfaces over one coat of primer complete all as specified and directed.

M&L for complete removal of plastered surface and apply two coat of oil bound distemper over coat of wall care putty to obtained smoothness of wall/ceiling surfaces over one coat of primer complete all as specified and directed.

M&L preparation and washing, rubbing down and stopping of distempered and painted surfaces of wall including cornices and applying one coat of acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete as per manufacturer's specification complete all as directed.

M&L for PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) of 25mm thick as in correction/levelling course, finished surfces even and rough to receive floor finish complete all as directed.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and incl over screed bed or bedding layer of mortar 15mm thick for laying tiles in cement mortar 1:6 complete all as directed.

-ditto- but as in skirting over 10mm thick rendering as in backing coat of CM 1:4.

M&L 35mm thick flush shutters, solid core construction, with partical board core and plywood face panels, both face is covered with decorative face veneer with glipping/frames complete (Design and pattern approved by AGE(I)) all as specified.

Anodised aluminium powder coated window two or three track or side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and approved by AGE(I).

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor 140mm long complete.

S&F Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F 100mm MS butt hinges cold rolled mild steel, and fixed complete all as specified and directed.

S&F Aluminium anodised, barrel tower bolts 150mm of extruded section and fixed

S&F Aluminium anodised, handles 150mm of extruded section and fixed

S&F for Powder coated aluminium frames and shutters/grills for door and window, ventilator or framing with one or more rebates joining cleat for fixing etc of any thpe, side hung shutter, sliding shutters etc complete all as specified and directed by Engr-in-Charge.

M&L for Rubber gasket EPDM/Neoprene for fixing glass pane in aluminium frame work/door/window complete all as specified and directed by Engr-in-Charge.

S&F Sheet glass 4mm thick, ordinary quality and glazing with oil putty in square of any size in each pane all as directed by Engr-in-Charge

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples

S&F in repair for Drapary rod 20mm dia, mild steel, chromium plated with fixing brackets, stops etc all as specified and directed by Engr-in-Charge.

S&F in repair Brackets suitable for drapary rod, mild steel, chromium plated etc all as specified and directed by Engr-in-Charge.

M&L RCC 1:1.5:3 (20mm graded aggregate) nominal mix as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as directed.

M&L preparation wood surfaces with two coats of Synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) of 25mm thick as in padding course, finished surfces even and rough for roof treatment complete all as directed.

M&L for 10mm thick plastering in CM 1:3 on concrete surfaces finished even and smooth complete all as specified and as directed.

Supply only Integral waterproofing compound.

Applying Oil bound Bitumen primer @ 0.20 Kg/Sqm all as specified and directed by Engineer-in-Charge.

M&L APP minimum 4mm thick polymeric membrane minimum weighing not less than 4kg/sqm and reinforced with polyster nonwoven fabric matt(wt. not less than 150 gms/sqm) & applying a coat of blown hot Bitumen over the membrane @ 12.0 kg/sqm complete all as specified and directed by Engineer-in-Charge.

M&L PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) 100mm thick as in sub base complete all as specified and directed.

M&L for PCC 75mm thick, 1:4:8 type D-2 using 40mm stone aggregate as in sub base of flooring and mass concrete complete all as specified and directed.

M&L Cement concrete 1:4 :8 type D2 using (40 mm graded aggregate) as in filling, fdn, mass concrete and sub base of floors etc.

Surface excavation n. exc. 30 cm deep and averaging 15 cm deep and getting hard/dense soil.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out hard soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,

Excavation in trenches in exc 1.5 m wide and not exc 1.5 M depth for foundation and getting out in soft and loose soil.

Returning, filling in including spreading leveling watering and well ramming in layers not exc 25 cm (soil)

Removing excavation materials not exc 50 Metre and deposition where directed at a level not exc 1.5 M above the starting point (soil).

M & L hard core of broken bricks gauge n. exc 63 mm, deposited spreaded and leveled in layer not exc 15 cm thick, watered and rammed to atrue surface, broken stone or boulder.

M&L Plain cement concrete 1:3:6 type C-1(using 20mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets copings, kneelers, apex stones, bed plates including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for provinding 100mm thick cement concrete in 1:2:4 type B1, (using 20mm graded stone aggregate) finishing cement concrete surface even and fair without using extra cement as base complete all as directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and pigment complete all as specified and directed.

M&L for Prepolished Chequered cement concrete tiles of size 30cm X30cm X 25mm thick, set and jointed and pointed in neat cement slurry in floors with grey cement and pigments over 15 mm thich screed bed in CM 1:6 complete all as specified and directed.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia for securing with clips quality conforming to deformed or twisted bars.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) all as specified and as directed

M&L Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, incl welding, drilling to RCC pillar all as specified and directed by Engr-in-Charge.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L preparation steel surfaces with two coats of Synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for prep of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and as directed complete.

M&L for Point wiring with 1.5 sqmm, single core ,PVC insulated, unsheathed FRLS cable, 1100 volts grade, IS -694 marked, with multi stranded copper conductor and earth continuity copper conductor cable of same size as in phase/neutral and connected to common earth dolly drawn through and including PVC conduit/casing and caping of suitable size alongwith fittings and accessories, fixed /laid on wall/beam/coloumn and also incl steel terminal box embedded in wall suitable for mounting of switches sockets regulators etc complete for one light point/ one fan point, controlled by one switch 5 amps one way

All as per item No 1 above but throug stove enamelled Steel coduite

All as per item No 1 above but for one socket out let 5A , independent with cable 1.5 Sq.mm(for WM fan)

All as per item No 1 above but for one socket out let 15A , independent with cable 2.5 Sq.mm

S & F modular switch 1 way 6A, 1 module

S & F modular socket 6A 2/3 pin combined, 2 module 16A 2 module.

S & F switch piano 6 Amps one way flush type

S & F switch piano 16 Amps one way flush type

S & F socket oulet 2 in one ,3 pin 6 Amps flush type

S & F socket oulet 2 in one ,3 pin 6 and 16 Amps flush type

Supply and fix in surface mounted LED light fittings 1X22W,220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper coductor cable of suitable size from ceiling rose complete

Supply and fixing ceiling fan complete with blade, down rods, electronic regulators and accessories, 230 V , 1200 Mm sweep ,service value 6.00 BEE , five star rated with brushless direct current motor (BLDC)

Supply and fixing wall mounted fan 300 MM sweep 4 starrated, Swing off white,Make Havells moael No FHWSWSTIVR12 OR equivallent in Crompton/Khaitan

Supply and fix fan regulator AC 230 V electronic step type

Supply and fix ceiling rose 3 terminals

S & F MCB distribution board SPN 2 way single door 240V powder coated with 200 Amps rated bus bar neutral link etc.

S & F MCB SPN 6 to 32 Amps10 KA, 'C' Series, 240V, 50HZ, ISI Marked .

Supply and fix XLPE insulate armoured heavy duty electric cable with aluminium conductor 1100 V grade 6 Sq.mm

Supply, installation, commisioning of water coolers fully stainless steel, electric driven single phase having approximate storage capacity 40 Ltr and cooling capacity 40 Lit/hr

ANAND REFRIGERATION (BID ID -3445517)

Suneetha Engineers and Contractors (BID ID -3445873)