MAINT / REPAIR TO CERTAIN B/R WORKS AT AAU UNDER AGE B/R-II AT GE JHANSI

Amount

Demolition of cement concrete incl terrazo flooring (un-reinforced) in ground floor and paving not exceeding 15cm thick (below or above ground level) built in cement mortar, complete all as specified and directed.

M&L for 75 mm thick cement concrete type D2 1:4:8 (using 40 mm graded stone agg) in sub base of flooring/ hard standing complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B1 (20mm graded stone aggregate) in flooring, complete all as specified and directed.

M&L for 75 mm thick cement concrete type C2 1:3:6 (using 40 mm graded stone agg) as in plinth protection and path laid in panels, not more than 3.0 mtr in length, laid to slope 1:30 incl forming joints 10mm wide and duly filled with mastic bitumen (01 part bitumen mixed with 03 parts of sand) surface, complete all as specified and as directed. (Note : The quoted rates are deemed to be inclusive of material against form work and joint fillings.)

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and directed.

M&L for Non skid ceramic colored tiles , 7 to 8 mm thick (square / rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm as in flooring etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed/ bedding layer in CM (1:6) complete all as specified and as directed.

M&L for ceramic colour tiles in vertical surface of size 350 X 250 x 7/450x300x7 mm thick, jointless type, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with and including 10 mm thick rendering in CM (1:4) for receiving the tiles, complete all as specified and as directed.

M&L for joint free, Vitrified Ceramic tiles of light shade 8 to 10 mm thick (square/rectangular) polished , area of each tile n.exc 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed.

All as per item here-in-above but on vertical surfaces such as skirting/dado over and including 10mm thick CM rendering in CM 1:4,complete all as specified and as directed.

M&L for joint free, Vitrified Ceramic tiles of dark shde, double charged/ultracharged 8 to 10 mm thick (square/rectangular) polished , area of each tile exc 0.42 but n.exc 1.00 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed.

All as per item here-in-above but on vertical surfaces such as skirting/dado over and including 10mm thick CM rendering in CM 1:4,complete all as specified and as directed.

Dismantling stone slabs and tiles of any description or thickness laid , bedded and pointed in any mortar as in floors, aprons etc. complete all as specified and directed.

M&L for factory made, chequered cement concrete tiles of any colour 30 cm x 30cm x 20 to 22 mm thick, set & jointed and pointed in neat cement slurry mixed with grey cement and pigments, laid over and including 15mm thick screed bed or bedding layer in CM 1:6, complete all as specified and directed.

M&L for factory made machine pressed precast concrete interlocking paver block of any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with coloured pigment made of PVC moulded (or rubber mould) with vibrating system, with and including 50mm thick sand cushioning, including in CM (1:3) in edges of pavers, complete all as specified and directed. (Note : The cost of sand cushion and plastering to edges is included in quoted rate.)

M&L 20 mm thick granite slab of any type , tabled rubbed, machine cut, duly grinding, polishing, moulding etc of all outer edges / sharp corners, duly fixed in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4), incl pointing in grey cement (1:2) using marble dust with admixture of pigment to match with the shade of slab, complete all specified and directed.

M&L for green marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with, over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Dismantling timber scantling 40.0 sqcm and over in section in any position as in framed / unframed works such as roof purlins, rafters, fillets, ridges etc as in roof/ ceiling, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling boarding, cupborad any description, fixed in any position including fittings complete all as specified and directed.

M & L 18 mm thick factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations, kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges shall be paid separately)

Providing and fixing 2mm thick 16 to 19mm wide PVC edge binding tape of approved quality for cupboard/wardrobe shutters including necessary synthetic resin hot pressed to edges on binding machine etc. complete as per directions of Engineer- in-charge.

M&L for 18/19mm thick particle board, prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

Extra over rates of block board or veneered particle board for external teak wood 18/19mm lipping 6mm thick fixed with nails complete all as specified and directed.

S&F continuous (piano) hinges, mild steel bright finish in electro galvanized width of flat (when open) in 30mm, complete all as specified and directed

S & F drawer/shutter handles, projection drop (50mm to 65mm) on screwed plate complete all as specified and directed

S & F 100 mm aluminium anodise hasp and staple, safety type, aluminium anodised with hinge pin including bolt to hinge plate and fixed with screw complete all as specified and directed

Supply & Fix stainless steel magnetic catcher fancy type for kitchen cabinet / drawer complete all as specified and directed by Engineer-in-Charge.

S&F in repair Rubber bush (door seal) of 25mm wide fixed to door complete all as specified and directed

Demolition of brick work built in cement mortar or lime mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L for brick work with old size fly ash bricks, straight or curved on plan exc. 6 M mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for half brick thick wall with old size fly ash bricks, straight or curved on plan to any radius built in cement mortar 1:4, complete all as specified and directed.

M&L for 10 mm rendering thick in CM (1:6) on fair faces of brick work/concrete surfaces finished even & smooth (without using extra cement) including taking down cement plaster on brick or stone wall,dado and skirting etc including racking out joints hacking for key scrubbing down with water etccomplete all as specified and directed.

M&L for rendering 15mm thick in two coats (1st coat 10 mm thick in CM 1:6 & 2nd coat 5 mm thick in CM 1:4 with WPC) on fair faces of brick work/concrete surfaces, finished even & smooth (without using extra cement) including taking down cement plaster on brick or stone wall,dado and skirting etc including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed. Note: WPC in 5 mm thick 2nd layer plaster measured and paid separately.

M&L for 10 mm rendering thick in CM (1:6) on fair faces of brick work/concrete surfaces finished even & smooth (without using extra cement), complete all as specified and directed.

M&L for rendering 15mm thick in two coats (1st coat 10 mm thick in CM 1:6 & 2nd coat 5 mm thick in CM 1:4 with WPC ) on fair faces of brick work/concrete surfaces, finished even & smooth (without using extra cement), complete all as specified and directed. Notes: WPC in 5 mm thick 2nd layer plaster measured and paid separately.

M&L for preparation of new plastered surface of wall and applying two coat of cement based paint over and incl one coat of exterior grade cement based primer, complete all as specified and directed.

M&L for preparation of new plastered of wall surface and applying two coats of interior acrylic emulsion (OBD), over a coat of chalk whitening primer over and incl a layer 3mm thick of wall care putty to get even and smooth level finish on new plastered surface of internal wall, complete all as specified and as directed.

Taking down chowkhats with shutters (without taking off shutters from the frame) area exc 1.5 sqm but not exceeding 4 sqm each including cutting holes in brick/ stone wall built in cement / lime mortar, embedded portion exc half brick but n.exc one brick for inserting new hold fast and making good the disturbed portion/surfaces, in CM 1:3 complete all as directed.

All as per item here-in-above but not exc 1.5 sqm each

Taking down shutters of any description not exc 01 Sqm each, complete all as specified and directed.

Taking down shutters of any description exceeding 01 Sqm and not exc 02 Sqm each, complete all as specified and directed.

M&L for powder coated ( minimum thickness of powder coating not less than 50 micron) aluminium frame for doors, windows, ventilators with one or more rebates, fabricated out of powder coated aluminium hollow square or rectangular section of required size incl necessary joining cleats, fixing screws etc complete, having size of frame for doors 100mm x45mm x 3.18 mm thick; for window 104mm x 45mm x 3mm thick; for ventilators 59mm x 33mm x 2.5mm, complete all as specified and directed.

M&L for powder coated ( minimum thickness of powder coating not less than 50 micron) aluminium door shutters, aluminium section for top rail and styles 85mm x 45mm x 2.0mm thick; bottom rail 100mm x 45mm x 2mm thick and lock rail 100mm x 45mmx 2.0mm thick including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, incl powder coated aluminum hinges, powder coated aluminum snap beading, screws, handle , particle board, ACP sheet etc, complete all as specified and directed.

S & F of pressed steel frames 105x60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed.

M&L for second class hard wood plain, solid, straight chowkhats and frame, wrought framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints and fixing, complete all as specified and directed.

S & F rolled mild steel in Fe 290 (Gde-E- 165) as in framed work in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sidesand one face is covered with decorative face veneer with lipping/frame to match complete all as specified and directed.

S& fixed factory made plain framed panelled shutters 35mm thick of 2nd class hard wood (any number of panels) with panels of timber flat on both sides feather edges or panel of 9mm BWP commercial ply over 12mm thick veneered panticle board with commercial face veneers fixed to chowkhat . The size of rail and stile as per IS : 1003 (Part-1), kiln seasoned and chemically pressure treated complete all as spfd.

M&L for 35mm thick 2nd class hard wood glazed & skeleton shutter (fully glazed or gauged) open rebated & prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamfered sash bar, or rounded, fitted with & mitred beads for securing glass/wiremesh etc, conforming to IS-1003 Part-I & II; size of members of shutters as specified in SSR Part-I section–8, clause 8.24(a) complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F steel window "Box Type" double shutter with side hung shutters (glass and wiremesh) including 3.00 mm thick glass, stainless steel wire cloth 0.56 mm in nominal dia of wire and average width of aperture 1.18 mm, inbuilt MS grills, projecting type hinges with steel handle, steel peg stay complete with glazing bar dovetailed/welded complete all as specified and directed.

S&F powder coated ( minimum thickness of powder coating not less than 50 micron) aluminium window shutter (three shutter) sliding type with frame of powder coated aluminium channel section suitable for sliding aluminium shutters weighing 0.55Kg/M of three channel including necessary joining cleats glazing clips rubber packing Powder coated aluminium shop beading screws with two shutter Including 5mm thick coloured/plain glass and one shutter with stainless steel wire gauze including necessary locking arrangement and handle etc; as specified etc complete all as specified and directed.

S&F steel Ventilator "Box Type" double shutter with side hung shutters (glass and wiremesh) including 3.00 mm thick figured glass , inbuilt MS grills, projecting type hinges with steel handle, steel peg stay complete with glazing bar dovetailed/welded complete all as specified and directed.

M&L for powder coated ( minimum thickness of powder coating not less than 50 micron) aluminium ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, 5.5 mm thick figured glass, rubber packing, powder coated aluminium snap beading, screws etc, complete all as directed.

M&L for preparing new or previously untreated surfaces of wood or wood based materials of any description not otherwise described exc 10 cm width or girth and applying two coat of synthetic enamel paint over and including a coat of pink primer and layer of putty/filling material to get smooth & level finish, complete all as specified and directed.

S&F of aluminium alloy anodized sliding door bolt 300mm (aldrop bolt) length with hasp staple and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all specified and directed

S&F of 100 mm size butt hinges, stainless steel, bright finish with galvanized mild steel pin complete all specified and directed

S&F of 150mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed.

S&F of 150mm aluminum handle cast type anodized complete all specified and directed.

S&F of mild steel ordinary rat tail rod pattern springs of size 300mm including roller and roller plate complete all as specified and directed

S&F of 140 mm door stopper of aluminium body and tongue anodized with hard drawn steel spring fixed in floor complete all as specified and directed.

M&L for cement concrete 1:2:4 type B1 (20mm graded aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, copings, bond stones, bed plates for hold fast and the like including weathering, slightly rounded or chamfered angles and throating, , complete all as specified and directed.

M&L for mild steel angles, bars, flats etc, as in hold fasts, pipe clamps, plain angle cleats for securing purlins, supports for stiffening of fencing, wall ties and similar small articles confirming to Fe-290 Gde E-165, complete all as specified and directed.

S&F of stainless steel wire cloth 0.56 mm in nominal dia of wire average width of aperture 1.18 mm and fixed with tinned tacks of stainless steel wire staples to steel shutters or fixed with wooden beads to wooden joinery, complete all as specified and directed.

S&F in repair of aluminium alloy anodized sliding door bolt 300mm (aldrop bolt) length with hasp staple and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all specified and directed

S&F of 3 mm thick sheet figured glass pin headed type, not exc 0.50 sqm in each pane, duly fixed with oil putty or wooden bidding as required, including hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S&F of 3 mm thick sheet glass ordinary quality and glazing type, not exc 0.50 sqm in each pane, duly fixed with oil putty or wooden bidding as required, including hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S&F in replacement of stainless steel wire cloth 0.56 mm in nominal dia of wire average width of aperture 1.18 mm and fixed with tinned tacks of stainless steel wire staples to steel shutters or fixed with wooden beads to wooden joinery, complete all as specified and directed.

S & F in repair stainless steel curtain rod 25mm dia steel pipe cutting into length as required at site with and incl SS end caps/lobs and SS wall mounting brackets, complete all as specified and directed.

S & F in repair stainless steel rod 15mm dia steel pipe cutting into length as required at site with and incl SS end brackets, fixed in cupboard and similar works, complete all as specified and directed.

S&F of ringfit PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of Ringfit PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F PVC (SWR) vent cowl 75mm bore, jointing to waste pipe, complete all as specified and directed.

S&F PVC(SWR) vent cowl 110mm bore, jointing to waste pipe, complete all as specified and directed.

S&F PVC floor trap of 75 mm outlet, jointing to waste pipe, complete all as specified and directed.

M & L for PVC (SWR) gully trap 110 mm, setting and jointing with solvent cement complete all as specified and directed.

S & F 15 mm bore Galvanized Steel tubes, medium grade fixed to walls and ceilings or laid in floors, concealed or open incl cutting of grooves including taking up or down with connections and fittings all as specified and directed

S & F 20 mm bore Galvanized Steel tubes, medium grade fixed to walls and ceilings or laid in floors, concealed or open incl cutting of grooves including taking up or down with connections and fittings all as specified and directed

Supplying and laying of 16 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/wall including taking up or down with connections and fittings complete all as specified and directed.

Supplying and laying of 20 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches /wall including taking up or down with connections and fittings complete all as specified and directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning etc. and hoisting, reconnecting and re-fixing in any position of exc. 250 litres & not exc. 500 litres capacity of tanks inclusive of necessary tank nipple , gate valve, airpipe, and float valve date of cleaning of tank will be marked on the tank by stencil with synthetic enamaled paint in uniform size, size of letters & numbers should be 40mm. complete all as specified and directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning etc. and hoisting, reconnecting and re-fixing in any position of 1000 litres capacity of tanks, inclusive of necessary tank nipple , gate valve, airpipe and float valve date of cleaning of tank will be marked on the tank by stencil with synthetic enamaled paint in uniform size, Size of letters & numbers should be 40mm. complete all as specified and directed.

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered white colour 500 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, with and incl disconnecting and dismantling the existing un-serviceable PVC/RCC water tank on top of roof/slab of bldgs, complete all as specified and directed.

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered white colour 1000 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, with and incl disconnecting and dismantling the existing un-serviceable PVC/RCC water tank on top of roof/slab of bldgs, complete all as specified and directed.

S&F of 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed.

S&F of 20 mm dia of Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iorn pipe and fixed. (minium weight 20 mm-210 gms) etc, complete all as directed.

S&F in repair 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed.

S&F in repair 20 mm dia of Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iorn pipe and fixed. (minium weight 20 mm-210 gms) etc,complete all as specified and directed.

S&F in replacement of stainless steel sink, 1.00 mm thick for kitchen with plug, with and incl 40mm dia CP waste coupling, waste pipe of 750mm long, washers, cantilever brackets, connecting union etc overall approx size 495 mm x 420 mm with approx bowl size of 410 mm x 330 mm x 160 mm etc, complete all as specified and directed.

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm

S&F in replacement of stainless steel kitchen plate rack made out of 1 mm thick sheet of size 765x920mm and 220mm deep, weight not less than 7 Kg, complete all as specified and as directed.

S&F in replacement of pillar taps, 15 mm dia, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with long screwed shanks and fly-nuts, complete all specified and directed.

S&F in replacement of stop cock with long shank and cup (concealed type), 15mm dia with wall flange, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe / unions, complete all as specified and directed.

S&F in replacement of overhead shower of dia 125 mm round shape single flow, ABS body chrome plated fancy type, with and incl swivel type shower arm of 20mm dia with wall flange made of cast copper alloy, chromium plated fancy type, complete all specified and directed.

S&F in replacement of long body bib cock, 15 mm dia with wall flange made of cast copper alloy, chromium plated, complete all specified and directed.

S&F in replacement of angular stop cock 15 mm dia with wall flange made of cast copper alloy, chromium plated type, complete all specified and directed.

S&F in repair SS grating of squre/round shape, overall size of 150x150mm with hinge type openable jali of 100 mm dia size with and incl fixing with CM to floor/nahani traps etc, complete all specified and directed.

S&F in replacement of towel rail 600 mm long D type between flange and wall bracket made of cast copper alloy, chromium plated, complete all specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as directed.

S&F in replacement of PVC multipurpose cabinet mirror with front openable door of overall size 350 x 450 mm, complete all as specified and directed.

S&F in replacement of Brass CP connection 15mm dia and 45cm long with 2 Nos brass check nuts with washers for geyser, complete all as directed.

S&F in replacement of PVC waste pipe 32 mm dia 750 mm long with for wash hand basin or for kitchen sink, complete all as specified and directed.

S&F in replacement of waste coupling, chromium plated (half or full threaded), 32 mm dia size, complete all as directed.

S&F in replacement of waste coupling, chromium plated (half or full threaded), 40 mm dia size, for kitchen sink complete all as directed.

S&F in replacement of PVC connection 450 x 15mm dia PTMT (PVC), complete all as directed.

S&F in replacement of PVC connection 600 x 15mm dia PTMT (PVC), complete all as directed.

S&F in replacement of 10 ltr capacity PVC valve less symphonic action type flushing cistern, white, with inlet ball valve, float and handle with and including wall bracket, 32 mm dia PVC flush pipe and connected to squat pattern / pedestal pattern water closet, including all joints and making good to the wall & floor,complete all specified and directed.

S&F in replacement of 1st quality vitreous china squatting pan Orissa pattern of size 580x440 mm, white colour with integral foot rests water closet including flush pipe, P Trap and connecting cone but exluding flushing cistern, duly fixed in lime concrete bedding and making good of floor surface, complete all as directed.

S&F in replacement of 1st quality vitreous china wash hand basin, white flat/angle back, size 550x400mm, complete including necessary cutting for and pinning in ends of brackets) with and including wall brackets, PVC waste pipe of 750mm long, CP waste coupling of 32mm dia size, complete all as specified and directed.

S&F in replacement of 1st quality vitreous china ware European type WC with "P" or "S" type traps and same make plastic seat cover of white colour including flush pipe, fixing bolts etc and making good of the wall & floor surface, complete all as directed.

Supply & Fix in repairs Vitreous China wash down water closet pan (single unit, means one piece ), EWC, wall mounted/hung, white or off white coloured including concealed flushing cistern system & matching coloured seat covered fixed, complete all as approved by Engr-in-charge and directed.

Supply & Fix in repairs Vitreous China wash down water closet pan (single unit, means one piece), EWC, floor mounted, white or off white coloured including flushing cistern system & matching coloured seat covered fixed, complete all as approved by Engr-in-charge and directed.

Providing and fixing Table Top white Vitreous China wash basin of size (390x390x150) Oval shape with 32mm CP brass waste coupling, including C.P brass swan neck pillar cock 15mm size having long neck and Aerator, C.P brass bottle trap 32 mm size, extension pipes, wall flanges and concealed G.I clamps complete including making necessary holes and other cutting in the counter top and fixing the wash basin, pillar cock rigidily including making good the walls wherever required all complete as per the architectural drawings and as directed by Engineer-in-Charge. Note - (The rate is inclusive of wash basin, waste coupling, swan neck pillar cock, bottle trap, brackets, all other fittings and accessories required for completion of work. For the purpose of payment, only the number of wash basins provided and fixed in position shall be enumerated.)."

M&L for preparation of new steel or iron surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over and including a coat of red oxide primer complete all as specified and directed

S & F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F in replacement of corner glass shelf 300 mm with Chromium plated bracket guard and railing and fixing accessories, complete all as directed.

Demolition of RCC Not exc 15cm thickness Roofs, floors (other than ground floors), beams staircases, landing, chajjas, Cover slab and similar suspended work

M&L for RCC M-20 (Nominal Mix) (20 mm stone agg) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as spd

M&L for mild steel deformed TMT bars 5 mm To 10mm dia (as in reinforcement) cut to length, bent to shape require including cranking, bending spirally for hooking for column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as spd and directed by engr in charge

M & L for rough finish formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Demolition of cement concrete of any description and in any position of WC’s/Bathroom etc in sunken portion area above ground floor, removing demolished material completely and old waste pipe from sunken portion and cleaning the side/bottom surface of sunken floor with wire brush, complete all as specified and directed.

M&L PCC 1:5:10 Type E2 using 40mm graded stone aggregate as in mass filling in two layer in sunken portion complete all as spd and directed

M&L for 25 mm thick PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate as in padding levelling etc and roof kerbs with liquid water proofing solution finished even and fair with proper slope as prepatory works to water proofing treatment complete all as spd and directed by EIC. Note:-liquid water proofing solution shall be provided in 150ml in 50 Kg of Cement by weight and cost of liquid water proofing solutionmeasured and paid seperate item complete all as directed.

M&L for 15mm thick plastering in CM 1:3 along the wall of toilet and bath mixed with 3 % WPC and finished even and smooth without using extra cement complete all as specified and directed.

M&L for bitumen blown 80/100 grade applied hot, two coats to plastered surfaces of any description at the rate of 1.5 kg per sqm per coat complete all as specified and directed.

M&L for Polythene film black 50 micron laid in floor complete all as specified and directed.

M&L for 50mm dia G.I pipe as in spout to drain out if any leakage occures in the sunken portion complete all as spd

M&L for 55 mm thick PCC 1:2:4 type B0 using 20 mm graded stone aggregate as in padding levelling etc and roof kerbs with liquid water proofing solution finished even and fair with proper slope as complete all as specified and directed. Note:- WPC measured and paid separetely.

Supply only integral liquid water proofing compound LW++, mixed in CM as per manufacturer instruction, complete all as specified and directed.

M&L for preparation of old existing surface of wall and applying one coats of cement base paint complete all as specified and directed.

M&L for structural steel Fe-410-W(Gde-E-250) quality A for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, complete all as specified and directed.

Dismantling asbestos cement (corrugated or semicorrugate etc) sheet in roof covering, complete all as specified and directed.

S&F of pre-painted 0.50mm thick Gavalume Aluminium Zinc coating GI based corrugated / semi corrugated / trapezoidal steel sheet of any colour having tensile strength 550 MPa and AZ 150 grade as in roof covering/cladding to walls, fixed with self tapping screws, complete all as specified and directed.

S&F pre-painted Galvalume Aluminium Zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength 550 MPa and AZ 150 grade as in ridge of roof covering, fixed with self tapping screws, complete all as specified and directed.

Supply & Fix in repair auto closing hinge (CLIP-ON SOFT CLOSE) 35 mm of 0 crank (K15-00 or equivalent ) or 8 crank full overlay openable for kitchen cabinet shutters fixed complete al as specified and directed.

Supply & Fix in repair Ball bearing runner (drawer slide) 45 mm telescopic type (ST-210-1245-18) full extension having length 450 mm or more of load capcity 50 Kgs fixed with suitable type SS Screw complete all as specified and directed by Engineer-in-Charge.

Supply & Fix repair Stainless steel handles pullout 100 mm size fancy type for kitchen cabinet / drawer complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair chromium plated stainless steel wire basket (storage basket) pull out type for large utensil of size 480x500x150 mm of grade 304 with necessary fixing clips/screw complete all as specified and directed by Engineer-in-Charge.

Supply and fix chromium plated stainless steel wire basket (cup and saucer basket) pull out type for large utensil of size 380x500x100 mm of grade 304 with necessary fixing clips/screw complete all as specified and directed by Engineer-in-Charge.

Supply and in repair fix chromium plated stainless steel wire basket (Plate basket) pull out type for large utensil of size 380x500x165 mm of grade 304 with necessary fixing clips/screw complete all as specified and directed by Engineer-in-Charge. Make - AKS Kitchen Solutions or Equivalent

Supply and fix in repair chromium plated stainless steel wire basket (Cutlery basket) pull out type for large utensil of size 380x500x100 mm of grade 304 with necessary fixing clips/screw complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair chromium plated stainless steel wire basket (Grain Trolley) pull out type for large utensil of size 480x500x250 mm of grade 304 with necessary fixing clips/screw complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair chromium plated stainless steel wire basket (Bottle Pull out ) pull out type for large utensil of size 130x490x450 mm of grade 304 with necessary fixing clips/screw complete all as specified and directed by Engineer-in-Charge.

S & F in repair plastic water closet seat cover , white colour , closed pattern with flat bottom , fixed with S S Hingle/ aluminium hinge and screw complete all as specified and directed.

S & F in repair Brass CP mixer (swan neck for wash basin) for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

Khushi Muskan Engineer & Developer (BID ID -3106142)

M/S SHARADA ASOCIATE (BID ID -3127062)

S GOURAV PRAKASH ENTERPRISES (BID ID -3115150)

Ms Prakash Raikwar Traders Co. (BID ID -3115136)