Rehabilitation of Karivalamvanthanallur Big Tank, Kuvalaikanni Tank in Sankarankovil Taluk and Maruthankulam Tank, Koothadikulam Tank in Thiruvengadam Taluk of Tenkasi District.

Clearing light jungle with out uprooting and disposing of the same as directed by the Engineer complying with standard specification.

Earthwork in all soils except hard rock requiring blasting and conveying for formation of bund with lead of 0 to 100 metre deploying earth moving machineries and tippers including benching, formation of bunds, breaking clods, sectioning etc. complete including extra watering and compaction of earth fill layers to specified density of 95% of proctor density through deployment of appropriate compaction equipment (standard 8-10 ton power roller; short width drum vibratory power roller; vibratory power roller; fuel-operated vibratory plate compactor of adequate capacity, as per space available for compaction etc., complete complying with standard specification and as directed by the Departmental Officers.

Supplying demarcation R.C.C. pre cast post in Cement concrete M20 grade with well graded aggregates and the nominal maximum size of coarse aggregate of size 20 mm of size 0.15 x 0.15 x 1.20 M and fixing the post 40 Cm depth below ground level, the post includes using 4 numbers of 8 mm RTS main rod to a length of 1.325 M, using 6 mm MS 9 numbers as strrups with steel centering and painting the post with enamel paint to a height of 0.80 M alround the post etc. complete and conveying the post to the site of demarcation boundary such as tank bund and foreshore including earth work excavation for foundation in HSC, and the post embedded by using Cement concrete M10 grade with well graded aggregates and the nominal maximum size of coarse aggregate of 20 mm, as per the direction of the Engineers and complying with standard specification.

Dismantling, clearing away and carefully stacking material useful for reuse for any thickness of brick or stone masonry in Cement Mortar walls under 3 (Three) metres high complying with standard specification and as directed by the Engineer.

Earth work excavating and depositing on bank with a initial lead of 10 m & initial lift of 2m in Hard stiff clay, stiff black cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size of boulders hard gravelly soil complying with standard specification and as directed by the departmental officers. SS 20B (Open excavation)

Refilling the excavated earth in layers not exceeding 23cm thickness and watering to OMC (Optimum Moisture content) and compaction of each layer to 95% of proctor Density through deployment of appropriate compaction equipment (8-10T power roller) vibratory power roller of short width ( 0.90m width drum) power roller or vibratory power roller/fuel operated or electrically operated, vibratory plate compactors, ensuring compaction of designed bund section including side slopes etc., complete complying with standard specification and as directed by the Departmental Officers.

Earth work excavation for foundation in all kinds of soils and sub soils except hard rock requiring blasting full depth as may be directed and depositing the surplus earth in places shown by the Engineer in - charge of work and leveling the same with all leads and lifts including shoring, strutting, shuttering, baling out water wherever necessary and refilling the sides of foundation with excavated earth in layers of 15cm thick well rammed and consolidated etc. complete, complying with technical specifications and drawings as directed by the Engineer in - charge of work. (Specification No.4.2.2.)

Supplying and filling with CS sand of each layer not more than 15 cm thick including consolidation etc complete and as per the technical specifications directed by the Engineer in charge of the works For sluices, weirs sand retainig wall etc., complete complying with standard specification and as directed by the Departmental Officers.

Providing and placing in position of plain Cement concrete of grade M15 using hard well graded aggregates with the nominal maximum size of coarse aggregate of 40mm; weigh batching the ingredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 15 N/mm2 at 28days) including dewatering the placement site by bailing/pumping and by diverting wherever necessary; laying the concrete in layers of not exceeding 15 cm thick and in bays; compacting and finishing the surface with all leads and lifts; watering curing complete so as to attain the profile and strength specified in the approved drawing & specifications etc., complete complying with standard specification and as directed by the Departmental Officers.(Without Vibrations)

Providing and placing in Position of Plain cement concrete of grade M15 using hard broken stone aggregate of maximum nominal size of 20mm 40% and 40mm 60% to IS specified grading mixing by mixer machine including dewatering the placement site,laying the concrete in layers and in bays vibrating,compacting and finishing the surface with all leads and lifts watering curing to attain the profile and strength as specified in the drawing for various depth and height below and above ground level etc complete as directed by the Engineer in charge of work complying with the standard specification (with vibration).

Providing and placing in position of plain Cement concrete of grade M15 using hard broken granite coarse aggregates with the nominal maximum size of 20mm; weigh batching the ingredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 15 N/mm2 at 28days) including dewatering the placement site by bailing/pumping and by diverting wherever necessary; laying the concrete in layers of not exceeding 15 cm thick and in bays; compacting and finishing the surface with all leads and lifts; watering curing complete so as to attain the profile and strength specified in the approved drawing & specifications etc., complete complying with standard specification and as directed by the Departmental Officers.(With Vibrations)

Supplying and erecting water tight steel centering for sides and soffits including supports and strutting up to height of 3.29 m for plain surfaces such as RCC slab, Vertical Slab, Side slabs of RCC works with all cross bracings using mild steel B.G.10 gauge sheets of size 90cm x 60cm stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding laid over silver oak (country wood) joists of size 10cm x6.5cm spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centre to centre complete complying with standard specification and as directed by the by the Engineer in charge of work (The retrieved materials should be taken back by the contractor ). The payment for centering should be made after the concrete is laid etc.,

Centering without strutting

Centering with strutting

Providing and laying in position of Standardised Concrete Mix M25 in accordance with IS 456-2000 using 20 mm down graded hard broken granite stone jelly for all RCC items of works with minimum cement concrete of 350 kg/m3 and maximum water cement ratio of 0.55 with about (5 cum) 7730 kg of 20 mm machine crushed stone jelly and with about (3.30 cum) 5156 kg of 10 - 12 mm machine crushed stone jelly and with about (4.79 cum) 7670 kg of sand weigh batching the ingredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 25N/mm2 at 28days) including dewatering of placement site by bailing/pumping and by diverting wherever necessary laying the concrete in layers and in bays, Vibrating, compacting and finishing the surface water curing so as to attain the profile and strength specified in the approved drawing and specification and excluding the cost component of providing rigid and smooth centering and shuttering wherever necessary for various depths below ground level and various heights above ground level as per the direction of the Engineer complete in all respect but excluding the cost and placing of reinforced grill in position complying with standard specification

Providing and laying in position of Standardised Concrete Mix M20 in accordance with IS 456-2000 using 20 mm down graded hard broken granite stone jelly for all RCC items of works with minimum cement concrete of 325 kg/m3 and maximum water cement ratio of 0.55 with about (5 cum) 7730 kg of 20 mm machine crushed stone jelly and with about (3.30 cum) 5156 kg of 10 - 12 mm machine crushed stone jelly and with about (4.79 cum) 7670 kg of sand weigh batching the ingredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 20N/mm2 at 28days) including dewatering of placement site by bailing/pumping and by diverting wherever necessary laying the concrete in layers and in bays, Vibrating, compacting and finishing the surface water curing so as to attain the profile and strength specified in the approved drawing and specification and excluding the cost component of providing rigid and smooth centering and shuttering wherever necessary for various depths below ground level and various heights above ground level as per the direction of the Engineer complete in all respect but excluding the cost and placing of reinforced grill in position complying with standard specification

Supplying, fabricating & placing in position of mild steel or ribbed for steel grills for Reinforcement of RCC works including cost of steel and binding wire and labour charges for decoiling, cutting, bending and tying the grills complete complying

Providing and placing in position of plain Cement concrete of grade M20 using hard well graded aggregates with the nominal maximum size of coarse aggregate of 20mm; weigh batching the ingredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 20 N/mm2 at 28days) including dewatering the placement site by bailing/pumping and by diverting wherever necessary; laying the concrete in layers of not exceeding 15 cm thick and in bays; compacting and finishing the surface with all leads and lifts; watering curing complete so as to attain the profile and strength specified in the approved drawing & specifications etc., complete complying with standard specification and as directed by the Departmental Officers. without vibration Wearing coat Sluice & Weir)

Supplying and fixing new cut stone Roughly dressed to size all faces and set in cement mortar 1:3 (One cement and three sand by volume) mixed mechanically in approved mixer) including all incidental charges such as finishing, curing etc., complete complying with standard specification and as directed by the Departmental Officers

Fabricating and supply of country wood plug size of 40 x 40 cm and 45 cm to 60 cm height. The plug rod with 20 mm dia mild steel rod size of 3.0 m to 4.50 m height. The plug top side, middle, centre and bottom side covered iron strap - 3 nos. Plate thickness size 3 mm steel plate. The plug hole size 10 cm to 25 cm dia. etc., including cost of rod, wrought and put up and fixing in correct alignment in position. The plug painted with two coats of Varnish, the rod painted with two coats of best anti-corrosive paint and conveyance to the work site including loading, unloading. The rates should be inclusive of all taxes and duties and including fixing charges etc., complete complying specification and as directed by the Engineer.

Fabricating, Supplying and erection of Screw gearing steel shutters of size upto 1.00 m width consist shutters of skin plate made out of 8mm thick mild steel plate and horizontally stiffened with 65x65x6mm mild steel Angle at an interval not more than 0.50m and vertical stiffeners made out of same section at an interval not more than 0.60m and provided with 8mm mild steel gusset plate of required size on both sides fastened with rust free bolts and nuts etc. Conveying the fabricated shutter by using lorries including loading, unloading and leading the shutter to the vent. Dismantling the eroded shutter and shuttering arrangements by using necessary gas cutting equipment. Erecting the new shutter and the shuttering arrangements in the vent in proper position by using necessary hoisting equipment. The shutter shall be painted with two coats of Anticorrosive black paint over one coat of Red Oxide Primer. The rate including cost of materials consumables, labours power charges, conveyance charges for all equipment required conveying the dismantled materials to the section stores, cost of petty civil works, trial operation of shutter and warranty for 5 years etc.,complete.

Fabricating, Supplying and erection of Screw gearing steel shutters of size above 1.00 m and Upto 2.00m width consist shutters of skin plate made out of 8mm thick mild steel plate and horizontally stiffened with 100x50mm mild steel Angle at an interval not more than 0.50m and vertical stiffeners made out of same section at an interval not more than 0.60m and provided with 8mm mild steel gusset plate of required size on both sides fastened with rust free bolts and nuts etc. Conveying the fabricated shutter by using lorries including loading, unloading and leading the shutter to the vent. Dismantling the eroded shutter and shuttering arrangements by using necessary gas cutting equipment. Erecting the new shutter and the shuttering arrangements in the vent in proper position by using necessary hoisting equipment. The shutter shall be painted with two coats of Anticorrosive black paint over one coat of Red Oxide Primer. The rate including cost of materials consumables, labours power charges, conveyance charges for all equipment required conveying the dismantled materials to the section stores, cost of petty civil works, trial operation of shutter and warranty for 5 years etc.,complete.

Fabricating, supplying and fixing of 63mm dia Screw Rod made up of Mild Steel duly machined and fully threaded to suit the Head set Assembly and provided with required holes. Conveying and leading the screw rod to the worksite. Fixing the screw rod to the shutter gusset plate with required bolt and nut in proper alignment to the head set including dismantling the existing damaged screw rod, conveying and stacking at section store. The Screw rod should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, labours, charges for all fabricating and hoisting equipments, conveyance charges for labours and materials and warranty for 5 years etc., complete.

Supplying and fixing of Head Set Assembly Light duty with hexagonal nut (Approximate 50 Kg) made up of cast iron including moulding, machining and the hexagonal nut threaded to suit the Screw Rod provided with thrust bearings for smooth operation. Conveying and leading the head set assembly to the work site. Fixing the head set assembly to the top beam by using required rust free bolts and nuts in proper alignment including dismantling the existing damaged Head set assembly supplied with operating key and the both should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, labours, charges for wooden pattern, moulding and charges for labours and materials and warranty for 5 years etc., complete.

Supplying and fixing of Head Set Assembly Medium duty with hexagonal nut (Approximate 70 Kg) made up of cast iron including moulding, machining and the hexagonal nut threaded to suit the Screw Rod provided with thrust bearings for smooth operation. Conveying and leading the head set assembly to the work site. Fixing the head set assembly to the top beam by using required rust free bolts and nuts in proper alignment including dismantling the existing damaged Head set assembly supplied with operating key and the both should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, labours, charges for wooden pattern, moulding and charges for labours and materials and warranty for 5 years etc., complete.

Fabricating, Supplying and fixing of Top Beam made up of 150x75mm (ISMB 150) duly drilled to suit the Head Set Assembly with required bed bolt made out of 25mm mild steel round rod duly threaded with suitable anchorage arrangements to a height of 0.60m with necessary Fish plate made out of 12mm mild steel plate of size 0.30 x 0.15m 2Nos with required holes. Conveying and leading the top beam arrangements to the work site. Fixing the top beam arrangements at the top of the vent in correct position including dismantling the existing eroded top beam, conveying and stacking and the section stores. The top beam should be painted with two coats of AC black paint over one coat of Red Oxide primer. The Rate including cost of materials, labours, charges for all fabricating and hoisting equipments, cost of petty civil works conveyance charges for labours and materials and warranty for 5 years etc.., complete.

Fabricating, supplying and fixing of Shutter Groove Angle made up of 65x65x6mm Mild Steel angle for required height including welding hold fast of size 25x25x6mm Mild steel angle 2 Nos on both sides and conveying and leading the groove angle to the vents. Fixing the angle to the grooves in proper alignment including dismantling the existing damaged groove angles, conveying and stacking at section store. The groove angle should be painted with two coats of AC black paint over one coat of red oxide primer. The rate including cost of materials, consumables, labours charges for all fabricating and hoisting equipments, conveyance, petty civil works and warranty for 5 years etc., complete, etc.,

Groove Angle

Providing and fixing weep holes of 110mm dia pvc pipes of working pressure 4kg/m2 to a required length for protection wall, abutment and wing wall including cost of conveyance of all materials to work site including cost of labour charges for 90cm spherical back fill arrangements with 110mm dia and 20mm size hard granite broken stone charges at the peripery, the labour charges for fixing and to drain the back fill etc., complete complying with the standard specifications and as directed by the departmental officers.

Random rubble masonry in Cement mortar 1:4 (One cement and four sand) using new hard granite stones and bond stones including simultaneous pointing of the exposed surface with same mortar and all incidental charges such as baling out water curing, finishing complying with standard specification.

using Old stone 60%

using New stone 40%

Gravel packing 15cm thick for cement concrete block revetment or apron including stacking watering and consolidation etc., complete complying with standard specification and as directed by the Departmental Officers

Rough stone dry packing for revetment and apron using hard granite stones obtained from approved sources including the cost of new wedges for filling the gaps etc., complete complying with standard specification and as directed by the Departmental Officers.

using Old stone 60%

using New stone 40%

Pointing with cement mortar 1:3 (One cement and three sand) for flush pointing in Random Rubble masonry complying with standard specification.

Please Enable Macros to View BoQ information