Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹23.1 LAccepted-AOC E 73 FF GALI NO 17B SADH NAGAR PALAM COLONY NEW DELHI 110045 | SOUTH WEST DELHI | DELHI | 110045 | L1 | Accepted-AOC Being L1 Bidder | |
| 2 | L2₹26.9 L+₹1.6 L (6.19%)Rejected-Finance GROUND FLOOR F 11 PHASE II MAYAPURI WEST DELHI DELHI 110064 | DELHI | WEST DELHI | DELHI | 110064 | L2 | Rejected-Finance OTHER THAN L1 | |
| 3 | L3₹26.9 L+₹1.6 L (6.44%)Rejected-Finance ROOM NO 145 MASJID WALI GALLI GANESH MURTI NAGAR PART NO 2 COLABA MUMBAI 05 | L3 | Rejected-Finance OTHER THAN L1 | |
| 4 | L4₹28.0 L+₹2.7 L (10.6%)Rejected-Finance | L4 | Rejected-Finance OTHER THAN L1 | |
| 5 | L5₹29.0 L+₹3.7 L (14.5%)Rejected-Finance 1 225 5 6 SADAR BAZAR DELHI CANTT 110010 | NEW DELHI | DELHI | 110010 | L5 | Rejected-Finance OTHER THAN L1 |
| Sl No | Description | Qty | Unit | B.R. Enterprises L4 | M/s JAIMAA ASSOCIATES L6 | PRASAD ELECTRICALS L1 | CHOUDHARY ELECTRICAL L3 | M P TYAGI ENGINEERS AND CONTRACTORS L5 | AMIT ENTERPRISES L2 |
|---|---|---|---|---|---|---|---|---|---|
| 1.00 | Disconnecting electric connections from LT control panel and starter of submersible pump set of size 2 to 15 HP and removing the pipe line connections from discharge side and taking down/out submersible pump set along with column pipe from bore well with the help of chain pully block including transportation to workshop for repairs and back and lowering of same pump in bore well after repairs after replacement of rusted nuts, bolts, washers, rubber gasket etc including testing complete all as specified and as directed by Engineer-in-Charge. | 22 | EACH JOB | 1,500 ₹33,000 | 1,000 ₹22,000 | 6,000 ₹1,32,000 | 4,000 ₹88,000 | 999 ₹21,978 Lowest | 6,000 ₹1,32,000 |
| 2.00 | Disconnecting electrical connections from panel board including disconnecting the cable leads from the motor terminal box and taking down/out electric motor of any capacity and makes from base plate of pump set after opening the nuts, bolts etc / Dismantling the induction/Submersible motor and seperate the stator and rotor and removing the Unserviceable DE & NDE sede bearing, burnt winding wire from stator and rewinding the same as per existing supper enamelled copper wire gauge F class insulation used including varnishing and heating for drying of winding, transporting the motor to workshop for repair and back, re-installed after repair including testing complete all as specified and directed . | 450 | HP | 699 ₹3,14,550 | 500 ₹2,25,000 | 800 ₹3,60,000 | 700 ₹3,15,000 | 199 ₹89,550 Lowest | 550 ₹2,47,500 |
| 3.00 | Disconnecting electric connection and De-coupling the Centrifugal pump of capacity 5 to 10 HP and removing from foundation for repair after opening /cutting the rusted nuts, bolts etc and dismantling complete pump and repairing the same with replacing the following unserviceable spare parts i.e. CI Casing wear ring, interstage ring, stuffing box bush, lentern ring, eye bolt with nut, shaft sleeve, impeller key, coupling key, water liquid reflector, bearing cartridge, bearing plate, shaft bush, MS stud with nut, mechanical seal, gasket packing including grinding work of lathe machine if any and re-assembling the same including the transporting the pump from side to workshop for repair and back, re-installed at existing position after repair and providing new MS nuts, bolts,packing flange etc including testing complete all as specified and directed. | 2 | EACH JOB | 2,000 ₹4,000 | 1,000 ₹2,000 Lowest | 5,500 ₹11,000 | 2,000 ₹4,000 | 4,999 ₹9,998 | 4,000 ₹8,000 |
| 4.00 | Disconnecting of electric connection and De-coupling the Centrifugal pump of capacity 20 HP and removimg from foundation for repair after opening /cutting the rusted nuts, bolts etc and dismantling complete pump and repairing the same with replacing the following unserviceable spare parts i.e CI Casing wear ring, interstage ring, stuffing box bush, lentern ring, eye bolt with nut, shaft sleeve, impeller key, coupling key, water liquid reflector, bearing cartridge, bearing plate, shaft bush, MS stud with nut, gland rope gasket packing including grinding work of lathe machine and re-assembling the same including the transporting the pump from side to workshop for repair and back, re-installed at existing position after repair and providing new MS nuts, bolts,packing flange etc including testing complete all as specified and directed | 2 | EACH JOB | 3,000 ₹6,000 | 1,000 ₹2,000 Lowest | 7,000 ₹14,000 | 2,000 ₹4,000 | 4,999 ₹9,998 | 13,500 ₹27,000 |
| 5.00 | Disconnecting of electric connection and De-coupling the Centrifugal pump of capacity 30 HP and removing from foundation for repair after opening /cutting the rusted nuts, bolts etc and dismantling complete pump and repairing the same with replacing the following unserviceable spare parts i.e CI Casing wear ring, interstage ring, stuffing box bush, lentern ring, eye bolt with nut, shaft sleeve, impeller key, coupling key, water liquid reflector, bearing cartridge, bearing plate, shaft bush, MS stud with nut, gland rope or Mechanical seal as applicable on site, gasket packing including grinding work of lathe machine and re-assembling the same including the transporting the pump from side to workshop for repair and back, re-installed at existing position after repair and providing new MS nuts, bolts,packing flange etc including testing complete all as specified and directed. | 5 | EACH JOB | 3,800 ₹19,000 | 1,200 ₹6,000 Lowest | 8,000 ₹40,000 | 3,000 ₹15,000 | 4,999 ₹24,995 | 14,000 ₹70,000 |
| 6.00 | Disconnecting of electric connection and De-coupling the Centrifugal pump of capacity 40/50HP and removing from foundation for repair after opening /cutting the rusted nuts, bolts etc and dismantling complete pump and repairing the same with replacing the following unserviceable spare parts i.e CI Casing wear ring, interstage ring, stuffing box bush, lentern ring, eye bolt with nut, shaft sleeve, impeller key, coupling key, water liquid reflector, bearing cartridge, bearing plate, shaft bush, MS stud with nut, gland rope or Mechanical seal as applicable on site, gasket packing including grinding work of lathe machine and re-assembling the same including the transporting the pump from side to workshop for repair and back, re-installed at existing position after repair and providing new MS nuts, bolts,packing flange etc including testing complete all as specified and directed. | 6 | EACH JOB | 3,800 ₹22,800 | 1,500 ₹9,000 Lowest | 12,000 ₹72,000 | 3,000 ₹18,000 | 4,999 ₹29,994 | 15,000 ₹90,000 |
| 7.00 | Disconnecting the electric connection of monoblock pump of capacity 10 HP and removing the same from foundationfor repair after opening /cutting the rusted nuts, bolts etc and dismantling complete pump and repairing the same with replacing the following unserviceable spare parts i.e CI Impeller, GM shaft sleeve, Mechanical seal, water seal, water liquid reflector, MS stud with nut, gasket packing including grinding work of lathe machine and re-assembling the same including the transporting the pump from side to workshop for repair and back, re-installed at existing position after repair and providing new MS nuts, bolts,packing flange etc including testing complete all as specified and directed. | 3 | EACH JOB | 2,000 ₹6,000 | 1,000 ₹3,000 Lowest | 4,500 ₹13,500 | 1,800 ₹5,400 | 4,999 ₹14,997 | 11,000 ₹33,000 |
| 8.00 | Dismantling complete submersible pump of capacity 5-7.5 HP and repairing the same with replacing the following unserviceable spare parts i.e GM bush, rotor sleeve, water seal,cable seal, thrust bearing, sealing ring, upper & lower housing flange upper & lower with stud and nut, wire mesh, drain plug, SS distance sleeve, impeller key, inter ring GM neck ring, Guide bush, GM impeller/EPV Impeller, CI section chamber,SS coupling, CI stage bowl, T bolt with nut including grinding work of lathe machine and re-assembling the same testing, complete all as specified and directed | 16 | EACH JOB | 5,500 ₹88,000 | 1,000 ₹16,000 | 6,000 ₹96,000 | 1,700 ₹27,200 | 999 ₹15,984 Lowest | 3,500 ₹56,000 |
| 9.00 | Dismantling complete submersible pump of capacity 10-12.5 HP and repairing the same with replacing the following unserviceable spare parts i.e GM bush, rotor sleeve, water seal,cable seal, thrust bearing, sealing ring, upper & lower housing flange upper & lower with stud and nut, wire mesh, drain plug, SS distance sleeve, impeller key, inter ring GM neck ring, Guide bush, GM impeller/EPV Impeller, CI section chamber,SS coupling, CI stage bowl, T bolt with nut including grinding work of lathe machine and re-assembling the same testing, complete all as specified and directed | 6 | EACH JOB | 3,500 ₹21,000 | 1,500 ₹9,000 Lowest | 7,000 ₹42,000 | 2,000 ₹12,000 | 1,999 ₹11,994 | 3,500 ₹21,000 |
| 10.00 | Disconnecting the all electric connection and lifting the raw sewage pump set from sludge well/equilisatin tank and dismantling complete raw sewage submersible pump of capacity 5 to 7.5 HP and repairing the same with replacing the following unserviceable spare parts i.e GM bush, roror sleeve, water seal, thrust bearing, sealing ring, upper & lower housing flange upper & lower with stud and nut, wire mesh, drain plug, SS distance sleeve, impeller key, inter ring GM neck ring, Guide bush, GM impeller, CI section chamber,SS coupling, EPV impeller, CI stage bowl, T bolt with nut including grinding work of lathe machine and re-assembling the same testing complete all as specified and directed | 3 | EACH JOB | 5,500 ₹16,500 | 1,500 ₹4,500 Lowest | 6,000 ₹18,000 | 3,500 ₹10,500 | 2,999 ₹8,997 | 6,500 ₹19,500 |
Tender Value
₹44.8 L
EMD Value
₹89,500
Closing Date
1 Oct 2025, 6:00 pmClosed
GE(U)(W/S) DELHI CANTT
GE(U)(W/S) DELHI CANTT 110010
REPAIR/MAINTENANCE OF INSTALLED PUMPING SETS, ELECTRIC MOTORS, CONTROL PANELS AND CONNECTED ITEMS OF WATER SUPPLY INSTALLATIONS OF 1/5 GR UNIT AREA, CVD FAMILY QUARTER AREA, CVD PUMP HOUSE, SIGNAL GROUP, PIRU VIHAR PALAM BAGH AND DAD PANCHWATI AREA
2025_MES_729108_1
GE/WS/Token No-31 OF 2025-26
Open Tender
Civil Works
Item Rate
180 days
GE(U)(W/S) DELHI CANTT
AS PER NIT AND TENDER DOCUMENTS
6 documents required · 6 mandatory
₹500
GE(U)(W/S) DELHI CANTT
₹89,500
1 Dec 2025
3 Sept 2025
3 Oct 2025
3 Sept 2025
1 Oct 2025
18 Sept 2025
Amount
Disconnecting electric connections from LT control panel and starter of submersible pump set of size 2 to 15 HP and removing the pipe line connections from discharge side and taking down/out submersible pump set along with column pipe from bore well with the help of chain pully block including transportation to workshop for repairs and back and lowering of same pump in bore well after repairs after replacement of rusted nuts, bolts, washers, rubber gasket etc including testing complete all as specified and as directed by Engineer-in-Charge.
Disconnecting electrical connections from panel board including disconnecting the cable leads from the motor terminal box and taking down/out electric motor of any capacity and makes from base plate of pump set after opening the nuts, bolts etc / Dismantling the induction/Submersible motor and seperate the stator and rotor and removing the Unserviceable DE & NDE sede bearing, burnt winding wire from stator and rewinding the same as per existing supper enamelled copper wire gauge F class insulation used including varnishing and heating for drying of winding, transporting the motor to workshop for repair and back, re-installed after repair including testing complete all as specified and directed .
Disconnecting electric connection and De-coupling the Centrifugal pump of capacity 5 to 10 HP and removing from foundation for repair after opening /cutting the rusted nuts, bolts etc and dismantling complete pump and repairing the same with replacing the following unserviceable spare parts i.e. CI Casing wear ring, interstage ring, stuffing box bush, lentern ring, eye bolt with nut, shaft sleeve, impeller key, coupling key, water liquid reflector, bearing cartridge, bearing plate, shaft bush, MS stud with nut, mechanical seal, gasket packing including grinding work of lathe machine if any and re-assembling the same including the transporting the pump from side to workshop for repair and back, re-installed at existing position after repair and providing new MS nuts, bolts,packing flange etc including testing complete all as specified and directed.
Disconnecting of electric connection and De-coupling the Centrifugal pump of capacity 20 HP and removimg from foundation for repair after opening /cutting the rusted nuts, bolts etc and dismantling complete pump and repairing the same with replacing the following unserviceable spare parts i.e CI Casing wear ring, interstage ring, stuffing box bush, lentern ring, eye bolt with nut, shaft sleeve, impeller key, coupling key, water liquid reflector, bearing cartridge, bearing plate, shaft bush, MS stud with nut, gland rope gasket packing including grinding work of lathe machine and re-assembling the same including the transporting the pump from side to workshop for repair and back, re-installed at existing position after repair and providing new MS nuts, bolts,packing flange etc including testing complete all as specified and directed
Disconnecting of electric connection and De-coupling the Centrifugal pump of capacity 30 HP and removing from foundation for repair after opening /cutting the rusted nuts, bolts etc and dismantling complete pump and repairing the same with replacing the following unserviceable spare parts i.e CI Casing wear ring, interstage ring, stuffing box bush, lentern ring, eye bolt with nut, shaft sleeve, impeller key, coupling key, water liquid reflector, bearing cartridge, bearing plate, shaft bush, MS stud with nut, gland rope or Mechanical seal as applicable on site, gasket packing including grinding work of lathe machine and re-assembling the same including the transporting the pump from side to workshop for repair and back, re-installed at existing position after repair and providing new MS nuts, bolts,packing flange etc including testing complete all as specified and directed.
Disconnecting of electric connection and De-coupling the Centrifugal pump of capacity 40/50HP and removing from foundation for repair after opening /cutting the rusted nuts, bolts etc and dismantling complete pump and repairing the same with replacing the following unserviceable spare parts i.e CI Casing wear ring, interstage ring, stuffing box bush, lentern ring, eye bolt with nut, shaft sleeve, impeller key, coupling key, water liquid reflector, bearing cartridge, bearing plate, shaft bush, MS stud with nut, gland rope or Mechanical seal as applicable on site, gasket packing including grinding work of lathe machine and re-assembling the same including the transporting the pump from side to workshop for repair and back, re-installed at existing position after repair and providing new MS nuts, bolts,packing flange etc including testing complete all as specified and directed.
Disconnecting the electric connection of monoblock pump of capacity 10 HP and removing the same from foundationfor repair after opening /cutting the rusted nuts, bolts etc and dismantling complete pump and repairing the same with replacing the following unserviceable spare parts i.e CI Impeller, GM shaft sleeve, Mechanical seal, water seal, water liquid reflector, MS stud with nut, gasket packing including grinding work of lathe machine and re-assembling the same including the transporting the pump from side to workshop for repair and back, re-installed at existing position after repair and providing new MS nuts, bolts,packing flange etc including testing complete all as specified and directed.
Dismantling complete submersible pump of capacity 5-7.5 HP and repairing the same with replacing the following unserviceable spare parts i.e GM bush, rotor sleeve, water seal,cable seal, thrust bearing, sealing ring, upper & lower housing flange upper & lower with stud and nut, wire mesh, drain plug, SS distance sleeve, impeller key, inter ring GM neck ring, Guide bush, GM impeller/EPV Impeller, CI section chamber,SS coupling, CI stage bowl, T bolt with nut including grinding work of lathe machine and re-assembling the same testing, complete all as specified and directed
Dismantling complete submersible pump of capacity 10-12.5 HP and repairing the same with replacing the following unserviceable spare parts i.e GM bush, rotor sleeve, water seal,cable seal, thrust bearing, sealing ring, upper & lower housing flange upper & lower with stud and nut, wire mesh, drain plug, SS distance sleeve, impeller key, inter ring GM neck ring, Guide bush, GM impeller/EPV Impeller, CI section chamber,SS coupling, CI stage bowl, T bolt with nut including grinding work of lathe machine and re-assembling the same testing, complete all as specified and directed
Disconnecting the all electric connection and lifting the raw sewage pump set from sludge well/equilisatin tank and dismantling complete raw sewage submersible pump of capacity 5 to 7.5 HP and repairing the same with replacing the following unserviceable spare parts i.e GM bush, roror sleeve, water seal, thrust bearing, sealing ring, upper & lower housing flange upper & lower with stud and nut, wire mesh, drain plug, SS distance sleeve, impeller key, inter ring GM neck ring, Guide bush, GM impeller, CI section chamber,SS coupling, EPV impeller, CI stage bowl, T bolt with nut including grinding work of lathe machine and re-assembling the same testing complete all as specified and directed
Supplying and Fixing in replacement of Terminal Connection Plate of following capacity
Supply and fixing spare tyre for coupling type TC/P/011 after taking down/out as existing at site complete all as specified and as directed.
Supply and fixing spare tyre for coupling type TC/P/013 after taking down/out as existing at site complete all as specified and as directed
Supply and fixing spare tyre for coupling type TC/P/014 after taking down/out as existing at site complete all as specified and as directed
Supply and fixing spare tyre for coupling type TC/P/015 after taking down/out as existing at site complete all as specified and as directed
Supply and Fixing in replacement of Ball Bearing 6205
Supply and Fixing in replacement of Ball Bearing 6305
Supply and Fixing in replacement of Ball Bearing 6306
Supply and Fixing in replacement of Ball Bearing 6307
Supply and Fixing in replacement of Ball Bearing 6308
Supply and Fixing in replacement of Ball Bearing 6309
Supply and Fixing in replacement of Ball Bearing 6310
Supply and Fixing in replacement of Ball Bearing 6311
Supply and Fixing in replacement of Ball Bearing 6312
Material and labour for painting Two coat of synthetic enamel paint as per existing pattern or scheme, on centrifugal pump & motor of any capacity rating 5-120 HP and suction/ delivery pipeline including NRV and sluice valve, MS Base channel including preparation of surfaces by scratching and removing the rust complete all as specified and as directed.
M&L for pump shaft stainless steel suitable for centrifugal pump set up to 15 HP including turning, grinding and balancing work complete all as specified and as directed.
M&L for pump shaft stainless steel suitable for centrifugal pump set up to 20-30 HP including turning, grinding and balancing work complete all as specified and as directed.
M&L for pump shaft stainless steel suitable for centrifugal pump set up to 40-50 HP including turning, grinding and balancing work complete all as specified and as directed.
M&L for CI Impeller suitable for centrifugal pump set up to 15 HP including turning, grinding and balancing work complete all as specified and as directed.
M&L for CI Impeller suitable for centrifugal pump set up to 20-30 HP including turning, grinding and balancing work complete all as specified and directed.
M&L for CI Impeller suitable for centrifugal pump set up to 40-50 HP including turning, grinding and balancing work complete all as specified and directed.
M&L for taking up the suction pipe of size 80/100/150 mm dia after opening of Nuts and Bolts and open the bottom plate of Swing type CI Valve and replace the unserviceable leather Gasket of swing disc as per existing size but of minimum thickness not less than 6 mm complete all as specified and directed.
Supply and fixing in replacement GI Nipple with flange welded, heavy duty 40 x 300 mm size complete all as specified and as directed.
Supply and fixing in replacement GI Nipple with flange welded, heavy duty 50 x 300 mm size complete all as specified and as directed.
Supply and fixing in replacement GI Nipple with flange welded, heavy duty 80 x 300 mm size complete all as specified and as directed.
Supply only GI column pipe, heavy grade, class 'C', 50 mm bore of 3 metre length, heavy duty, flange welded on both ends complete all as specified and as directed .
Supply Only GI column pipe, heavy grade, class 'C', 80 mm bore of 3 metre length, heavy duty, flange welded on both ends complete all as specified and as directed .
S&F in replacement of submersible cable of size 2.5 Sqmm 3 Core. 1100 Volt complete all as specified and directed by Engineer-in-Charge.
S&F in replacement of submersible cable of size 4 Sq mm 3 core , 1100 Volts Volt complete all as specified and directed by Engineer-in-Charge.
S&F in replacement of submersible cable of size 6 Sq mm 3 core, 1100 Volts Volt complete all as specified and directed by Engineer-in-Charge.
Testing the cables with high voltage DC testing machine and locating the fault in the cables by fault locating machine to pin point exact position of fault, disconnecting faulty 1100 volts LT cables of different sizes from both ends , removal of fault , Reconnection and testing of cables after removal of fault complete all as specified and directed by Engr-in-charge. NOTE: (i) 1100 volt cables and joints shall be measured and paid for seperately under respective items of schedule (ii) Retrieved old serviceable cable cover/ bricks will be laid in trenches for cable protection. If extra PCC cover / bricks and sand required at site shall be measured and paid separately under respective items of BOQs. (iii) Exacavation and earth work will be measured and paid for separately under respective items of schedule.
Supply and fixing in replacement heat shrinkable jointkit suitable for XLPE cable insulated screened PVC bedded armoured electric power cable heave duty 1100 volts grade, with straded aluminium conductor, cross sectional area 25/35 Sqmm, 3.5 core after taking down/out faulty portion as exists compete all as specified and as directed.
M & L for preparation of surfaces for painting of existing submersible pump sets of capacity 2 to 15 HP and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge.
Supply and fixing in replacement of Mild steel clamps in Mild steel flat of size 50mm x 6 mm with including two Nos Mild steel nut and bolts suitable for 50mm bore column pipe complete all as specified and directed.
Supply and fixing in replacement of Mild steel clamps in Mild steel flat of size 80 mm x 6 mm with including two Nos Mild steel nut and bolts suitable for 80mm bore column pipe complete all as specified anddirected.
Supply and fixing in replacement PVC insulated Aluminium wire 1100 volt, Double core of size 10.0 Sq mm complete all as specified and as directed.
Supply and fixing in replacement PVC insulated multistranded copper conductor wire 1100 volt, single core of following sizes complete all as specified and as directed.
Supply,Laying, jointing, Testing and commisioning of MS Pipe of following size, as per IS:1239 with and including MS flange, 16 mm thick welded for drilling of 16 mm dia bolts, nuts, washers, rubber gaskets etc laid in trenches complete all as specified and as directed.
Supply & Fixing in replacement MS Flange of following sizes, 16 mm thick, duly welded on ends of MS pipe including necessary cutting to existing MS pipe or in new MS pipe with flange joint including nuts, bolts, washers and rubber gaskets complete all as specified and as directed .
Supply and Fixing in replacement of Vibration Pad with nuts, bolts and washers, for existing capacity of 40-75 HP complete all as specified and as directed.
Supplying and laying XLPE insulated, armoured heavu duty electric cable with aluminium conductor 1100 Volts grade cross sectional area 25 Sqmm 3.5 Core laid in trenches/floor/wall incl taking out old unserviceable cable and connection to panel for incoming and outgoing using suitable aluminium lugs complete all as specified and as directed.
Supplying and laying XLPE insulated, armoured heavu duty electric cable with aluminium conductor 1100 Volts grade cross sectional area 35 Sqmm 3.5 Core laid in trenches/floor/wall incl taking out old unserviceable cable and connection to panel for incoming and outgoing using suitable aluminium lugs complete all as specified and as directed.
Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out in soft/ loose soil complete all as specified ans as directed.
Returning filling in trenches including spreading leveling watering and well ramming in layers not exceeding 25 cm thick complete all as specified and as directed.
Removing of excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all complete all as specified and as directed.
M&L for spread fine river sand in trenches complete all as specified ans as directed. (Note: For measurement purpose, punned down thickness shall only be taken.)
M&L for laying brick sub class 'B' old size burnt bricks for cable protection of size 230mmx115mmx75mm complete all as specified and as directed
M&L for taking out old and broken PCC pole of any size/height from the existing size by breaking the foundation and dismantlimg the cable connections complete all as specified and directed by Engr-in-Charge.
Excavating in post holes each not exceeding 0.5 cum in soft / loose soil, getting out, returning filling in and ramming earth or broken rubble mixed with around earth in layers not exceeding 25 cm thick, watering and removing surplus soil to a distance not exceeding 50 metre and making good surface complete all as specified and directed.
Supply, erecting and fixing in position Steel tubelar swaged poles complete with cast iron base plate finial taper plug bolts, nuts & screws as specified type 410 SP-31 (9 Metres long) complete all as specified and directed.
Providing PCC (1:4:8) type D-2 using 40mm graded crushed stone aggregate as in foundations filling mass concrete bed of pipe etc complete all as specified and directed.
Provinding PCC (1:2:4) type B-1 using 20mm grded crushed stone aggregate as in coping bed plate including weathering slightly rounded or chamfered angles and throating etc all as directed.,
Supply and fixing poly carbonate junction box , weather and vermin proof of suitable size including provn of 2 Nos aluminium strip 25x3.15 mm size bus bar single phase and neutral suitabely mounted on bus bar insulators , including one No. MCB SP 6 Amps for light control,drilling of holes.Provn of suitable size of GI nuts, bolts, earthing bolt, double washer and galvanised flat iron clamps of suitable size for taking connections and fixing on LT steel tubular poles complete with locking arrangement complete including cable gland of suitable size at entry and exit point of cable. Note: (i) Box shall be provided at 1 metre above the pedastal of pole. (ii) Quoted rate shall be deemed to include bus bars, MCB and clamps.
Openning of gland packing coupling and removing the unserviceable gland rope from centrifugal/Monoblock pump set of capacity 15 to 50 HP and fixing the new gland rope all as per existing size gland rope complete all as specified and directed.
Openning of gland packing coupling and removing the unserviceable gland rope from Sluice valve of size 100 to 300 mm dia and fixing the new gland rope all as per existing size gland rope complete all as specified and directed.
M&L for Decorative ultra slim round profile LED lightning fixture 20W,6000K, with extruded polycarbonate environmental friendly energy efficient incl taking down old unsv light fitting complete all as specified and as directed.
Supply and fixing in replacement 45 watt LED street light New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 including making connections with GI pipe 0.6mtr angle braket fixing on wall and connectng to ceiling rose with apropriate wire complete all as specified and directed.
Supply and fixing in replacement 90 watt LED street light New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 including making connections with GI pipe 0.6mtr angle braket fixing on wall and connectng to ceiling rose with apropriate wire complete all as specified and directed.
Supply and fixing exhaust Fan, heavy Duty 450 mm sweep, 1400 RPM Single pole 230V, 50Hz complete all as specified and directed.
Supply and fixing ceilling fan 1200 mm sweep Single pole 230V , 50Hz ,5 Star Ratingcomplete with fan regulator and down rod connection complete all as specified and directed.
S&F in replacement of GI Pipe 80 mm dia along with all fittings laid in trenches/floor all as per exisiting and specified by Engr-in-Charge.
S&F in replacement of GI Pipe 20 mm dia along with all fittings laid in trenches/floor all as per exisiting and specified by Engr-in-Charge.
S&F in replacement of Gun Metal Gate Valve 20 mm dia with iron wheel head screwed both ends for iron pipe as per IS-778 complete ISI marked complete and specified by Engr-in-Charge.
Supply and Fixing in replacement MS base channel of size as exists including cutting, welding and making hole, applying two coats of synthetic enamel paint over a coat of red oxide primer including dismounting existing Centrifugal pump motor set and taking out old unservicable existing MS Base chennel complete all as specified and as directed.
Supply and Fixing in replacement of MS foundation bolts with nuts and washers, size 20mm dia, 450 mm long complete all as specified and as directed (including breaking of hard standing foundation)
Supply and fixing rotational moulded polyethylene water storage tank , cylindrical vertical with closed top, 500 ltrs capacity, trippple layered hoisted and fixed in position after taking down as existing at site (of any capacity) complete all as specified an as directed. (Note: For Pump Priming purpose in pump house.)
Supply and fixing rotational moulded polyethylene water storage tank , cylindrical vertical with closed top, 1000 ltrs capacity, trippple layered hoisted and fixed in position after taking down as existing at site (of any capacity) complete all as specified an as directed. (Note: For Pump Priming purpose in pump house.)
M&L for development of bore well of any capacity and size at the pressure 10 kg/sqcm to 15 kg/sqcm by diesel engine driven air compressor of capacity 620 cfm includiing air pipe and connected items to improve the yield of tube well complete all as specified and directed by Engineer in charge.
M&L for development of bore well of any capacity and size at the pressure 22 kg/sqcm to 25 kg/sqcm by DTH Machine of capacity 1200 CFM including air pipe and connected items to improve the yield of tubewell as specified and directed by Engineer in charge. (Note : The rate deemed to include the cost of Transportation of machine and minimum 1 Hrs of running.)
Taking down cement plaster or cement lime plaster on PCC/Stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed .
Rendering 15 mm thick in CM (1:4) on fair faces of brickwork or concrete surfaces finished even & smooth.
Demolition of brick work or stone/boulder masonry built in cement mortar including all quoin jambs pillars etc.
M&L Brick work with sub class 'B' old size bricks bricks straight or cured on plan exceeding 6 m mean radius built in cement mortar 1:6
M&L for preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.
M&L for coloured Glazed ceramic tiles in vertical surfaces of size 300mm x 200mm, 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.
Demolition and dismantling concrete in ground floors and pavings n exc 15 cm thickness below or above ground level.
M & L for PCC (1:3:6) type C2 using 40mm graded aggregate as in foundation for including fair finish even and fair to exposed surfaces without using extra cement complete all as specified and as directed
Hacking out old broken glass any thickness, size, quality or description from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads including S&F 3 mm thick plain sheet glass ordinary quality in square not exceeding 0.5 complete all as specified and as directed
Supply and fixing & installation in replacement of perforated MS cable tray of size 350x50x2mm including horizontal and vertical bends, prepared hanging system and other accessories including painting of cable tray of complete all as specified and as directed.
M&L for fabrication (welding work ) of MS Header/ any size upto 300mm MS pipe at various pump house site for connection of pipe , arresting leakges on header complete all as specified and directed.
Excavation in trenches by cutting of road crossing, PCC hard standing for taking out/laying of cables including M& L for PCC (1:2:4) type B-I (with 20 mm graded aggregate) as in coping, grouting, finished even and smooth without using extra cement as on brick work/flooring complete making good the existing surface complete all as specified and as directed.
S&F in replacement of analog type time switch FM 1/ Quartz daily 240 VAC, flush mounting, 50 Hz Code No. J648F1.
M&L for replacement to Off load Change over Switch of rating 200 Amp, 4-Pole 415V as per IS / IEC: 60947 - 1&3 with dual mounting facility fixed at exisiting/new location incl the connections complete all as specified and directed by Engr-in-Charge.
M&L for replacement to Off load Change over Switch of rating 400 Amp, 4-Pole 415V as per IS / IEC: 60947 - 1&3 with dual mounting facility fixed at exisiting/new location incl the connections complete all as specified and directed by Engr-in-Charge.
M&L for replacement to Bus Bar Chambers of rating 200 Amp, 4-Pole 415V 6 Way as per IS: 2675/1966 with mounting facility fixed at exisiting/new location incl the connections complete all as specified.
M&L for replacement to Bus Bar Chambers of rating 400 Amp, 4-Pole 415V, 6 Way as per IS: 2675/1966 with mounting facility fixed at exisiting/new location incl the connections complete all as specified
Supply and installation of flanged ends Water Meter woltman type, including testing and making good connection with flanged ends, with gasket rubber sheet and nut & bolts etc ISI Marked fixing in horizontal / incline / vertical position, including taking out unserviceable of following sizes complete all as specified and as directed at site by the Engineer-in-Charge.
100 mm bore
Supply and Fixing in replacement of CI Foot valve of following size , Flanged ends, Swing type opration with rubber sheet as per IS-4038 including taking out unserviceable of following sizes all as specified and directed by Engineer-in-Charge. (Note :- Flanged joints complete with jointing material shall deemed to be included in the unit rate of this items.)
80 mm bore
100 mm bore
150 mm bore
Supply & fixing , install testing and commissioning of feeder pillar box , outdoor type cubical shape,three phase, 4 wire, copper bus bar for phases and neutral made out of CRCA sheet 3.15 mm thick ,factory fabricated , CPRI approved , powder coated ,dust and vermin proof , provn for ventilation , angle iron frame and four legs of 50x50x6mm thick angle iron ,2 ft long grouted on PCC foundation of height not less than 30 cm from the ground level , grouting properly ,and of suitable size to accomodate the items mentioned below and having seperate compartment /chambers for cable gallery busbar ,switch gear etc all as specified and comprising of following including necessary cable connections to the MCCBs ,voltmeter, Ammeter and cable lugs etc .
Copper bus bar with PVC sleeve rating 200 amps for Phase & 200 Amp for neutral - 01Set.
Phase indicating lamps LED type ( RYB) 01 Set
Incoming MCCB 125 Amp 3 pole 18 KA with adjustable thermal and fixed magnetic release -01 No
Outgoing MCCB 63 Amp 3-Pole 18 kA with adjustable thermal and fixed magnetic release - 01 Nos
FASD Stater ML-1.5 or MN-16 FASD-01 Nos
Analog time switch -01 No
Single phase preventer-01 No
Supply & Fixing in replacement for fixing MCCB's following sizes in existing location complete all as specified and as directed at site by the Engineer-in-Charge.
MCCB 32 Amps 3 Pole 16 KA
MCCB 63 Amps 3 Pole 16 KA
MCCB 100 Amps 3 Pole 16 KA
MCCB 125 Amps 3 Pole 16 KA
MCCB 160 Amps 3 Pole 36 KA
MCCB 200 Amps 3 Pole 36 KA
Supply & Fixing in replacement for fixing of Power Contacor MNX Series MNX 40 sizes in existing location complete all as specified and directed.
Supply & Fixing in replacement for fixing of FASD Starter ML 1.5, Suitable for Upto 12.5 HP Motor existing location complete all as specified and as directed at site by the Engineer-in-Charge.
Supply & Fixing in replacement for fixing of FASD Starter ML 2.0, Suitable for Upto 12.5 HP Motor existing location complete all as specified and as directed at site by the Engineer-in-Charge.
Supply and fixing in replacement 3 pole power contactor ML-1.5, 25 Amps suitable for fixing in existing panel complete all as specified and as directed.
Supply and fixing in replacement 3 pole power contactor ML-2, 32-40 Amps suitable for fixing in existing panel complete all as specified and as directed.
Supplying, laying, jointing, testing and commmisioning in Replacement of DI Pipe, class K-7 with inside cement mortar lining with spigot and socket ends laid in trenches Including taking out Old UNSC Pipe complete all as specified and as directed at site for the following sizes :- Note : - (i) Rubber gasket Joint (Tyton Joint) is deemed to be included in this unit rate of items (ii)Earth work shall be measured and paid separetely
100 mm bore
Supply and installation of flanged ends strainer/dirt box, PN-10 with stainless steel mesh suitable for water meter for potable water supplies on up stream of water meter to avoid foreign material entering into meter including taking out unserviceable of following sizes complete all as specified and as directed at site by the Engineer-in-Charge.
100 mm bore
Material and labour including jointing and testing of cast iron sluice valves class PN-1.0, conforming to IS:14846 flanged ends drilled having stainless steel spindle with cast iron wheel at top complete with nuts, bolts, washers and rubber gaskets including taking out unserviceable sluice valve and removal from site for the follwing sizes complete all as specified .
80 mm bore
100 mm bore
150 mm bore
Supply and fixing jointing and testing of cast iron Non return valve without by pass arrangment swing type confirming to IS 5312 flanged ends pressure rating PN 1.0 complete including taking out unserviceable NRV complete all as specified and as directed by Engineer-in-Charge. (Note - Flanged joints complete with rubber jointing materail shall deemed to be included in the unit rate of this item)
80 mm bore
100 mm bore
150 mm bore
Material and labour for DI specials like MJ Collars, Bends, tapers any type any radius and angle, Tee pieces single branch `Y' junction, double branch, cross (all sockets or socket and spigot) collars, DI connecting pieces one end flanged and other end spigot/socket, reducers/bell mouth pieces one end flanged and other end tapering as bell mouth for the size up to 250 mm dia bore.
Taking up GI/Nidhi/CI/MS Pipes including all fitting of the following sizes as specified and directed by Engineer-in-Charge :-
100 mm bore
An amount of Rs 1,04,370.00 shall be deducted from BOQ on account of schedule of credit
AMIT ENTERPRISES (BID ID -3434813)
CHOUDHARY ELECTRICAL (BID ID -3432996)
B.R. Enterprises (BID ID -3434088)
M P TYAGI ENGINEERS AND CONTRACTORS (BID ID -3438383)
M/s JAIMAA ASSOCIATES (BID ID -3434670)
stage.html
html • 0.06 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .