ADDITION / ALTERATION AND SPECIAL REPAIRS OF DIRECTOR BUNGALOW (BUILDING NO P-28) AT NMRL, AMBERNATH

Material and Labour for dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead For thickness of tiles 10 mm to 25 mm complete all as specified and directed by Engineer - in - charge.

Material and Labour for dismantling Dado/skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead complete all as specified and directed by Engineer - in - charge..

Material and Labour for dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead complete all as specified and directed by Engineer - in - charge.

Material and Labour for demolishing cement concrete Nominal concrete 1:4:8 or leaner mix manually/ by mechanical means including disposal of material within 50 metres lead complete all as specified and directed by Engineer - in - charge

Material and Labour for cement concrete 40mm thick type B-1 1:2:4 (using 20mm graded stone aggregate) 25 mm thick as in sub base & leveling course and finished surface even and fair without using extra cement complete all as specified and directed by Engineer - in - charge.

Material and Labour for Vitrified Ceramic tiles Light Shade 8mm to 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm in floor etc,set and jointed in neat cement sluryy and pointed in coloured cement to match as in floor laid over and including 15 mm thick screed bed in CM (1:4) complete all as specified and directed by Engineer - in - charge.

Material and Labour for Vitrified Ceramic tiles Light Shade 8mm to 10mm thick (square/rectangular) polished, ,set and jointed in neat cement sluryy and pointed in coloured cement to match as in skirting over 15 mm thick screed bed in CM (1:4) complete all as specified and directed by Engineer - in - charge. (Note : Size of tile as directed by Engr-in-Charge)

Material and Labour for Coloured Non skid ceramic tiles 7 to 8mm thick (square / rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm in floor etc set and jointed in neat cement slurry pointed in coloured cement to match as in floor laid over and including 15 mm thick screed bed in CM (1:4) complete all as specified and directed by Engineer - in - charge.

Material and Labour for glazed ceramic tiles in vertical surfaces 450 x 300 x 7-8mm thick as in dado set and jointed in neat cement slury and pointed in coloured cement to match laid over and including 10mm thick backing Coat in CM 1:4 complete all as specified and directed by Engineer - in - charge.

Material and labour for 18-20 mm thick granite (of any type) work (table rubbed and poilshed) in steps, jambs, pillars, window-cills, cooking platforms and like in 15 mm thick cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Material and Labour for making plinth protection 50mm thick of cement concrete 1:3:6 (using stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including expansion joint every 2m interval and necessary excavation, levelling & dressing & finishing the top smooth complete all as specified and directed by Engineer - in - charge.

Dismantling doors, windows and clerestory windows (steel or wood or pvc) shutter Of area 3 sq. metres and below including chowkhats, architrave, holdfasts etc. complete all as specified and directed and stacking within 50 metres lead.

Dismantling doors, windows and clerestory windows (steel or wood or pvc) shutter Of area beyond 3 sq. metres including chowkhats, architrave, holdfasts etc. complete all as specified and directed and stacking within 50 metres lead

Providing and fixing PVC Door Frame of size 50x47 mm with a wall thickness of 5 mm (± 0.2 mm), made out of single piece extruded PVC profile, with mitred cut joints and joint with 2 nos of PVC bracket of size 190 mm x 100 mm long arms of cross section size 35 x 15 mm & self driven self taping screws, the vertical door profiles to be reinforced with 40x20 mm M.S. rectangular tube of 0.8 mm , including providing EPDM rubber gasket weather seal throughout the frame, including jointing 5 mm PVC frame strip with PVC solvent cement on the back of the profile. The door frame to be fixed to the wall using 8 x100 mm long anchor fasteners complete all as specified and directed by Engineer -in- charge.

Providing and fixing PVC Door Decorative finish (wood grained finish) 35 mm thick factory made Solid panel PVC Door shutter, made out of single piece extruded soild PVC profiles, 5 mm (± 0.2 mm) thick, having styles & rails (except lock rail) of size 95 mmx 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross section size 35 mm x 17 mm x 1 mm at each corner. Single piece extruded 5 mm thick solid PVC Lock rail of size 115 mm x 35 mm, out of which 75 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel, all complete all as specified and directed by Engineerin-charge.

Providing Second class hard wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) complete all as specified and directed.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed by Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete all as specified and directed by EngineerIn- Charge

Providing and fixing Second class hard wood 30 mm thick wire gauge shutters with ISI marked M.S. pressed butt hinges bright finished of required size using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws complete all as specified and directed by Engineer-in- Charge

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc complete all as specified and directed by Engineer-In- Charge

Providing and fixing 125x90x4.00 mm ISI marked, IS : 1341, M.S. heavy weight butt hinges with necessary screws etc. complete all as specified and directed by Engineer-In- Charge

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (using stone aggregate 20 mm nominal size) for fixing hold fast including repairing of disturbed plaster ( while taking down Door/window,ventilator frame) and matching the repaired surface with existing one complete all as per direction of Engineer-In- Charge

Providing and fixing 300x16 mm aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete all as specified and directed by Engineer-In- Charge

Providing and fixing 125 mm chromium plated brass handles with necessary screws etc. complete all as specified and directed.

Providing and fixing 200x10 mm aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete all as specified and directed by Engineer-In- Charge

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete all as specified and directed by Engineer-In- Charge

Providing and fixing aluminium Powder coated aluminium Frame (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete (Glazing, paneling and dash fasteners to be paid for separately) complete all as specified and directed by Engineer-In- Charge

Providing and fixing aluminium Powder coated aluminium (minimum thickness of powder coating 50 micron) work for Siliding shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) complete all as specified and directed by Engineer-In- Charge

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) with EPDM rubber / neoprene gasket etc. complete all as specified and directed by Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item)

Providing and fixing fly proof stainless steel With aluminium beading grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm complete all as specified and directed.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc With frosted glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) with EPDM rubber / neoprene gasket etc. complete all as specified and directed by Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item)

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete all as specified and directed.

Material and Labour for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces complete all as specified and directed.

Demolishing brick work In cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead complete all as specified and directed by Engineer-in-charge.

Material and Labour for Brickwork with fly ash brickes old size, straight or curved on plan exc 6m mean radius,built in C.M. 1:6, complete all as specified and directed.

Material and Labour for Cement Concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in bed blocks, coping etc including necessary form work complete all as specified and directed.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead complete all as specified and directed.

Material and Labour for Plastering 15mm thick on fair faces of brick work or concrete surfaces in Cement Mortar 1:4 finished even and fair complete all as specified and directed. Note:- WPC will be measured and paid separately.

Material and Labour for rendering 10mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Material and Labour for rendering 5 mm thick in CM 1:3 on ceiling fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Material and Labour for preparation of Newly Plastered surfaces of Wall and applying Two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification over a coat of primer complete all as specified and directed.

Material and Labour for preparing surfaces of new plastered and applying two coats of exterior emulsion paint over a coat of primer complete all as specified and directed.

Material and Labour for preparation of newly plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

Material and Labour for complete removal of existing treatment on wall surfaces and applying two coat of distemper oil emulsion over a coat of primer and 3 mm thick wall care putty complete all as specified and as directed.

Material and Labour for complete removal of existing treatment on ceiling surface and applying two coat of white wash complete all as specified and directed.

Material and Labour for Preparation of new steel surfaces of exc. 10cm width or girth of any description and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Material and Labour for painting one coat with synthetic enamel paint on old steel surfaces of any description over 10 cm width or girth including preparation of surfaces complete all as specified and directed.

French spirit polishing :Two coats on new works including a coat of wood filler complete all as specified and directed.

Material and Labour for applying priming coat for new wood work With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) and Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer including Painting wood work with Deluxe Multi Surface Paint of required shade. Two coats applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10sqm of approved brand and manufacture as per manufacturers specifications complete all as specified and directed.

Providing and fixing 100 mm sand cast Iron grating for gully trap including jointing with solvent cement, including jointing to waste pipe and fixed in cement concrete type B1 1:2:4 complete all as specified and directed.

Disconnecting damaged overhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level complete all as specified and directed by Engineer-in-charge.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank complete all as specified and directed by Engineer-in charge.

Providing and fixing 20 mm nominal bore ball valve (brass) of approved quality, High or low pressure, with plastic floats complete all as specified and directed by Engineer-in charge.

Providing and fixing CPVC gate valve with C.I. wheel of approved quality (screwed end) of 20mm dia bore and fixed complete all as specified and as directed.

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete all as specified and directed by Engineer-in charge.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete all as specified and directed by Engineer-in charge.

Providing and fixing White Vitreous China Wash basin of size 630x450 mm with C.I. brackets, 15 mm C.P. brass pillar tap, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require complete all as specified and directed by Engineer-in charge.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete all as specified and directed.

Providing and fixing 15 mm nominal bore C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 complete all as specified and directed by Engineer-in charge.

Providing and fixing uplasticised PVC connection pipe 45 cm length with brass unions 15 mm nominal bore complete all as specified and directed by Engineer-in charge.

Providing and fixing C.P. brass 15 mm nominal bore bib cock of approved quality conforming to IS:8931 complete all as specified and directed by Engineer-in charge.

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 100 mm diameter complete all as specified and directed by Engineer-in charge.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make complete all as specified and directed by Engineer - in - charge

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms complete all as specified and directed.

Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead :75 to 80 mm dia pipe complete all as specified and directed.

Providing and fixing Single socketed pipes 75 mm diameter on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion complete all as specified and directed.

Providing and fixing Single socketed pipes 110 mm diameter on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, complete all as specified and directed.

Providing and fixing 75 mm bend on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion complete all as specified and directed.

Providing and fixing 110 mm bend on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion complete all as specified and directed by Engineer-in charge.

Providing and fixing 75 mm Single tee with door on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion complete all as specified and directed by Engineer-in charge.

Providing and fixing 110mm Single tee with door on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion complete all as specified and directed by Engineer-in charge.

Supply and Fix PVC (SWR) Vent cowl 75 mm dia complete all as specified and directed.

Supply and Fix PVC (SWR) Vent cowl 110 mm dia complete all as specified and directed.

Providing and fixing cup board shutters 25 mm thick, with Pre-laminated flat pressed three layer particle board or graded wood particle board IS: 12823 marked, exterior grade (Grade l Type ll), having one side decorative lamination and other side balancing lamination, including IInd class hard wood lipping of 25 mm wide x12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete all as specified and directed by Engineer-in-Charge

Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) complete all as specified and directed by Engineerin-Charge.

Providing and fixing 15 mm nominal dia Pipes Chlorinated Polyvinyl Chloride (CPVC) pipes Concealed work, including cutting chases and making good the wall etc, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete all as specified and directed by Engineer in Charge.

Providing and fixing 20 mm nominal dia Pipes Chlorinated Polyvinyl Chloride (CPVC) pipes for External work, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete all as specified and directed by Engineer in Charge.

Providing and fixing 15 mm nominal dia CP Brass Single lever wall mixer of quality & make as approved and complete all as specified and directed by Engineer in charge.

Providing and fixing square-mouth S.W. gully trap 180x150 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design complete all as specified and directed.

Providing and fixing mild steel CP 20mm external dia and 1.60 mm thick curtain rods with two brackets fixed with brass screws and wooden plugs etc. wherever necessary complete all as specified and directed by Engineer-in charge.

Removing existing water proofing treatment of any type all complete all as specified and directed by Engineer-in-charge and disposing off out side MD land.

Demolishing Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) cement concrete manually/ by mechanical means including disposal of material within 50 metres lead complete all as specified and directed by Engineer - in - charge.

Providing and laying in position cement concrete with smooth finish of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) complete all as specified and directed by Engineer-in charge.

Supply only liquid water proofing compund complete all as specified and directed.

Material and Labour for applying water based polyurethane modified dispersion (single component cold applied, non toxic, VOC complaint) in 03 coats including 01 coat of primer of same material after dilution of water at 50% of specific primer matching same material as per manufacturer specification and as directed by GE /Engr-in Charge Properties of Poly urethane based chemical shall confirm to following Technical Parameters: (i) Highly elastic (ii) UV resistance (iii) Adhesion to concrete >1N/Sqmm (iv) Tensile strength not less than 2 0 N/Sq mm for free film (v) Elongation not less than 300% (vi) Solid content by weight not less than 60% (vii) Air/water permeability BSEN 12390 at 5 bar 72 hours should be NIL and minimum dry film thickness of water proofing membrane must be 1.0 mm (viii) Accelerated weathering (ASTM 453) Pass 1000 hours (ix) Reaction to fire- non inflammable NOTE : 1.To be applied by the Rep of manufacturer’ s authorized applicator mentioned only. Contractor has to provide manufactrurer’s Test certificate for the above mentioned technical parameters. 2. For accessible terrace and inaccessible terrace. 300 mm height of vertical surface / parapet wall to be treated with same specification of slab 3. Make:- Bostik, Berger, Fosroc, Sika, Asian or any other make approved by E-in-C’s Branch for PU based water proofing treatment

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead complete all as specified and directed.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval and complete all as specified and directed by Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc Fixed to steel windows by welding including priming coat with approved steel primer all complete all as specified and directed by Engineer-in charge.

Providing and fixing Steel work In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc complete all as specified and directed by Engineer-in charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required complete including taking down existing unservicable AC sheets all as specified and directed by Engineer-in charge.

Supplying and fixing 80x1.25 mm M.S. laths with 1.25 mm thick top cover rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters complete all as specified and directed by Engineer-in charge.

Providing and fixing 6mm thick both sides Pre-laminated cement bonded HDHMR board as per IS : 15786:2008 of approved brand and shade with suitable full threaded steel screws etc. on the backing of racks, drawer, cupboard, kitchen cabinet under kitchen counter etc. complete all as specified and directed by Engineer-in-charge

Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed HDHMR grade marine ply as per IS 710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete all as specified and directed by Engineer-in-charge.(Payment of providing and fixing auto closing hinges shall be paid separately)

Providing and fixing 19mm thick both side balancing lamination factory pressed HDHMR grade marine ply as per IS 710 of approved brand boxes, shelves, racks, almirah, cupboard and drawer etc. including necessary nails, screws etc. complete all as specified and directed Engineer-in charge

Providing and fixing 200 mm long stainless steel fancy handle of approved make fixed with SS screws etc. complete all as specified and directed by Engineer-in-charge.

Providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic type) of approved make/brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete all as specified and directed by Engineer-in-charge.

Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete all as specified and directed by Engineer- in-charge

Providing and fixing ready made 304 grade stainless steel Modular kitchen basket and accessories such as right angle basket (Plain Cup & Saucer, plant, Partition, Bottle rack, Thali, Cutlery) kitchen utensil basket, Dinner set basket, kitchen grain basket, Multipurpose basket as per site requirement including finishing (wherever required) and fittings. The same shall be fixed with necessary stainless steel nuts & bolts, Stainless Steel screws & telescopic channel etc. as per direction of Engineer-in charge. (For payment purpose only weight of Stainless steel basket shall be considered excluding weight of all fixing accessories such as nuts, bolts, fasteners telescopic basket channels etc. Payment of providing and fixing telescopic channel shall be paid separately) complete all as specified and directed.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 using stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying factory made chamfered edge 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.

Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, laid over and including on 20 mm thick bed of cement mortar 1:4 Light shade pigment using white cement complete all as specified and direction

Providing and laying 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Dismantling of the ceiling fan/exhaust fan and painting the same with one coat of spray painting with synthetic enamel paint of approved brand and manufacture to give an even shade, including cleaning of surface with detergent and replacing the damaged rubber reel, nuts and bolts with washers and safety pins, reinstalling the same as required.

Wiring for light point with 1.5 sq mm FRLS PVC insulated copper conductor single core cable in recessed medium class PVC conduit, modular plate, suitable GI box and earthing the point with 1.5 sq mm FRLS PVC insulated copper conductor single core cable etc. as required for One light point controlled by one; one way

All as per item No 105 above but for One ceiling/Exhaust/ Wall fan point controlled by one; one way switch

All as per item No 105 above but for One 3 pin 5 Amp socket out let controlled by one switch on indep board.

Wiring with 2.5 sq mm FRLS PVC insulated multistranded copper conductor cables single core cable in surface/recessed medium class PVC conduit for one 3 pin socket outlet, 5/15Amps, independent, and earthing the point with 2.5 sq mm FRLS PVC insulated, unsheathed, copper conductor single core cable etc. as required

Supply and fixing Basic all purpose surface and wall mounted LED batten 10 Watts with aluminum housing & integrated electronic driver. complete with all accessories including pre wired and connecting up with twin core twisted flexible copper cable of suitable size complete all as required

Supply and fixing LED light fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing Elegantly designed sleek surface mounted pressure die-cast aluminium luminaire 15 Watts in powder coated white finish in square profile with optimized heat sink for efficient heat dissipation and independent electronic LED driver.

Supply and fixing Decorative wall light, stainless steel, rust free fixture with white glass diffuser suitable for 9 W LED lamp E27 base.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete

Supply and fixing 32/40 mm dia x 2.0 meter long G.I. pipe (medium class) bracket for mounting of fluorescent / HPMV / HPSV / LED street light fitting on pole/wall including bending the pipe to the required shape, 2 Nos 40 mm x 3 mm flat iron clamps with nuts, bolts and washer, painting the flat iron with primer and finish paint etc. as required.

Supply and fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. (a) 15/16 Amp switch, 1 module

(b) 6 Pin 15/16 A socket outlet

(c) 3 Pin 5/6A Socket outlet

supply and fixing 3 module (100 mm x 75 mm) size/modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required

Supply and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plat etc. as required.

Supply and fixing 3 pin, 5A ceiling rose on the existing junction box/ wooden block including connections etc as requied

Wiring for circuit. Submain wiring along with earth wire with the 2 x 4 sq mm + 1 x 4 sq mm eath wire of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required including taking down old unserviceable submain wiring

Wiring for circuit. Submain wiring along with earth wire with the 2 x 2.5 sq mm + 1 x 2.5 sq mm eath wire of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required including taking down old unserviceable submain wiring

Supply and fixing CRCA sheet steel, RAL 9003, powder coated Vertical TPN DB double door, 12' way, IP 54 protection with provision for 3 pole and 4 Pole MCCB as incomer and SP/TP MCBs as outgoings, conforms to IS 8623-1 & 3, IEC 61439-1 & 3, IK 09, provided with insulated vertical phase bus-bars, neutral bar/s with shroud/s, earth bar/s, sticking saddles, cement spill protector, color-coded interconnecting wire set, cable ties' blanking plates and circuit identification labels including taking down old unserviceable distribution board complete all as required

Providing and fixing 100A rating, 30 KA breaking capacity, FP MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including driling holes in cubicle panel, making connections, etc., as required including taking down old unserviceable MCCB.

Supply and Fixing 5A to 32A rating, 240V, 10kA, "C" curve, miniature circuit breaker suitable for inductive load of single pole in the MCB DB complete with connection, testing and commissioning etc as required including taking down old unserviceable MCB.

Supply and fixing 20/32A, 240V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug alongwith 20/32A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required including taking down old unserviceable socket outlet.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and directed.

Earthing with GI earth plate 600mm × 600mm× 6mm thick including accessories,and providing masonary enclusure with cover plate having locking arrangment and watering pipe of 2.7 meter long etc with charcoal/ coke and salt as required in any type of strata including taking down old unserviceable earthing.

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. wire in 15 mm dia G.I. pipe from eath electorde including conneciton with G.I. thimble excavation and re-filling as required including taking down old unserviceable one.

Supply and fixing Heavy duty Electric chimney of size 90cm with stainless steel baffle filter and suction capacity not less than 1150 cum/hr and outlet pipe of 150 mm dia all as directed.

Taking down old unserviceable LT cables any size from trenches including disconnecting cables and stacking of cables within 50 metres lead

Material and labour for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 70 sq. mm, 3.5 core (Earthwork will be measured and paid separately) including necessary lugs and glands complete all as specified and directed.

Supply and fixing post top lantern LED type 40 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete.

Material and labour for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 6 sq. mm, 3 core complete (Earthwork will be measured and paid separately) including necessary lugs and glands complete all as specified and directed.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : 2.10.1 All kinds of soil

Supply and spreading stone crushed sand of approved quality for cushioning of UG cable laid in trenches all as specified and directed

Supplying and laying reinforced precast concrete cable cover, classClass LV, Type I, flat, size 250 mm x 150mm x 40mm

Please Enable Macros to View BoQ information