CLEANING OF OVER HEAD TANKS INACCESSIBLE ROOFS OLD UNSERVICEABLE PIPE LINES REPLACEMENT OF INTERNAL WATER SUPPLY LINES SANITARY FITTINGS RAIN WATER PIPES AND DAY TO DAY MAINTENANCE FOR THE ADDRESSABLE SYSTEM OF ARMAAN ROUTINE COMPLAINTS IN MAR

Amount

Demolition of cement concrete and paving not exc 15 cm thick (below or above ground level) complete all as specified and as directed.

Demolition of brick work /stone masonry/PCC block masonry built in cement mortar of any description all as specified and directed.

Dismantling floor, hearth or wall tiling including including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the the premises complete all as specified and as directed.

Taking down cement plaster of any description including raking out joints, hacking for key and disposing of debris to a distance exc 1 Km out side MD land complete all as specified and directed.

Precast cement concrete block masonry with solid blocks exc. 10 cm in width and setting in cement mortar 1:6 type C1 1:3:6 ( using 20 mm graded aggregate) complete all as specified and as directed.

15mm thick rendering on brick or concrete surface in cement mortar (1:6) and finishing the surface with even and smooth without using extra cement complete all as specified and directed.

Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM(1:4) finishing the surfaces even and fair mixed with approved water proofing compound complete all as specified and directed. NOTE :- WPC will be measured and paid separately.

Rendering 5 mm thick on ceiling /RCC surfaces in cement mortar (1:3) and finishing the surface with even and smooth without using extra cement complete all as specified and directed.

Preparation of newly plastered ceiling surfaces of any description and applying three coats of white wash complete all as specified and directed.

Preparation of newly plastered surfaces of walls and applying two coats of cement based paint over a coat of alkali resistant primer all as specified and as directed.

Preparation of new plaster surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of oil bound emulsion distemper over a coat of alkali reistant primer on wall complete all as specified and directed.

Supply only approved integral liquid water proofing compound all as specified and as directed.

Plain Cement Concrete (1:2:4), type B-0 using 12.5 mm graded stone aggregate as in floors 25mm thick, as in sub base to floor complete all as specified and as directed.

Non skid ceramic coloured tiles 7-8mm thick(square/rectangular) area of each tile exceeding 0.11 Sqm but n.exc .18 Sqm as in floors set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed.

Glazed coloured ceramic tiles as in vertical surfaces 350 x 250x 7 mm/ 450 x 350 x 7 mm/ 300x450x7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including backing coat 10mm thick in CM (1:4) on fair faces of brick work or concrete surfaces complete all as specified and as directed.

Plain Cement Concrete, (1:3:6), type C-1, using 20 mm graded crushed stone aggregate, 75mm thick as in plinth protection, laid in alternate bays (not exceeding 2 Sqm each) finishing the concrete surface even and smooth at top without using extra cement and providing joints throughout the thickness of plinth protection, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight all as specified and directed

Vitreous china wash basin white flat back size 550x400mm excl chain and plug and porcelain stopper but incl CI bracket. waste fittings, brass chromium plated for glazed ware sinks, basins etc with long screwed shanks and flynuts, flange end bedded in red leead cement and other end fixed, PVC waste pipe 75 cm long complete fixed in repairs all as specified and directed.

Vitreous china wash down water closet pan (pedestal pan) including fixing bolts, flush pipe anti syphonage pipe, plastic water closet seat, coloured, closed pattern with flat bottom and cover, mild steel chromium plated or aluminium hinging device etc complete of CERA model Cat Parpt No. 2008 and 2308 or equivalent fixed in repairs complete all as specified and directed.

Vitreous china squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including PVC(SWR) 'P' or 'S' trap connecting to flush pipe and to anti syphonage pipe, etc. complete including making good to floor fixed in repairs complete all as specified and directed.

Viterous china urinals, bowl type (back or corner wall type), complete fixed in repairs including providing and fixing plugs, beddings urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe.

PVC valveless, syphonic action type, flushing cistern, 10ltr capacity,low level, white, with inlet, ball valve, float and handle including brackets, connections to pipes and fixing of chain and pull, or lever, fixed in repairs complete all as specified and directed.

Taking up or down steel tubing 15mm dia and connections including cleaning for refixing or removal to store all as directed.

Taking up or down steel tubing 20mm dia and connections including cleaning for refixing or removal to store all as directed.

Taking up or down steel tubing 25mm dia and connections including cleaning for refixing or removal to store all as directed.

20mm dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings, fixed to wall, ceiling or laid in floors complete all as specified and as directed.

20mm dia medium grade Galvanised iron tubing with all fittings and fixed to wall, ceiling or laid in floors etc complete all as directed.

25mm dia medium grade Galvanised iron tubing with all fittings and fixed to wall, ceiling or laid in floors etc complete all as directed.

25mm dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings, fixed to wall, ceiling or laid in floors complete all as specified and as directed.

Brass chromium plated overhead shower rose 100 mm size with or without swivel joints, any size, including fixing to steel pipe or union all as per Prayag Cat No BOS-86 or equivalent makes specified in PS ifxed in repairs complete all as specified and as directed.

Bib taps, 15mm dia fancy type, cast copper alloy, chromium plated, screwed down, screwed for iron pipe all as per Prayag Cat No PIS-06H or equivalent makes specified in PS fixed in repairs complete all as specified and as directed.

Pillar taps, 15mm dia, cast copper alloy, chromium plated, screwed down, screwed for iron pipe all as per Prayag Cat No PIS-02H or equivalent makes specified in PS fixed in repairs complete all as specified and as directed.

Stop valves, 15mm dia fancy type, cast copper alloy, chromium plated, screwed down, screwed for iron pipe all as per Prayag Cat No PIS-26 or equivalent makes specified in PSfixed in repairs complete all as specified and as directed.

Stop valve, 15mm dia, chromium plated concealed type with long shank and cup fixed in repairs all as per Prayag Cat No. PIS-18H or equivalent makes specified in PS complete all as specified and as directed.

Bib taps, 15mm dia fancy type long body, cast copper alloy, chromium plated, screwed down, screwed for iron pipe all as per Prayag Cat No PIS-08H or equivalent makes specified in PS complete all as specified and as directed.

Angle cock, 15mm dia, chromium plated, cast copper alloy, screwed down high pressure with capstan head handle screwed both ends or for unions etc all as per Prayag Model No-PR-544 or techno commercially equivalent makes specified in PS complete all as specified and as directed.

Health faucet, brass body with 1mtr SS braided rubber hose pipe and wall hook all as per Prayag Model No-BEA-81/ or techno commercially equivalent makes specified in PS complete all as specified and as directed.

Brass Chromium plated tubler towel rail, 20mm dia D type 600mm long between flanges all as per Prayag, Model No: BA 40 or techno commercially equivalent maks specified in PS complete all as specified and as directed.

Soap dish chromium plated brass all as per Cat Part No BA-45 of Prayag or equivlaent makes fixed to wall as in repairs complete all as specified and as directed.

PTMT Shelf of minimum weight 300gms of size and pattern as approved fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed.

Bib taps standard of PTMT, fancy type, any colour screwed for iron pipe suitable for 15mm dia fixed in repairs all as directed.

Pillar taps, standard of PTMT, any colour screwed for iron pipe suitable for 15mm dia fixed in repairs all as directed.

Angle Stop valves, standard of PTMT, any colour screwed for iron pipe suitable for 15mm dia fixed in repairs all as directed.

PVC connections 15mm dia with PTMT nuts of length of 600 mm long fixed in repairs complete all as specfied and as directed.

PVC connections 15mm dia with PTMT nuts of length of 450 mm long fixed in repairs complete all as specfied and as directed.

32 mm dia waste fittings, brass, chromium plated for sinks,basins,etc with long screwed shanks and flynuts,flange end fixed in repairs complete all as specified and as directed

40 mm dia waste fittings,brass,chromium plated for sinks,basins,etc with long screwed shanks and flynuts,flange end fixed in repairs complete all as specified and as directed.

PVC corrugated waste pipe 40mm dia, 800mm long fixed in repairs complete all as specified and as directed.

PVC corrugated waste pipe 32mm dia, 800mm long fixed in repairs complete all as specified and as directed.

PVC(SWR) floor trap,75mm dia, plain with grating including jointing with solvent cement fixed in repairs complete all as specified and as directed.

Grating doom 100mm dia of PTMT (Minimum weight 25gms) all asper Prayag Cat No FT-03M or equivalent make complete fixed in repairs all as specified and directed.

75 mm bore PVC (SWR) pipes, type 'B' single socketed in any length with rubber ring joints fixed to wall including PVC clamps all as specified and as directed.

All as per Sl Item No. 1.052 here in before but 110 mm dia. .

PVC (SWR) bends 75mm dia,of any radius with access door, type 'B' fixed in repairs complete all as specified and as directed.

All as per Sl Item No. 1.054 here in before but 110 mm dia. .

PVC (SWR) junction single (single T) equal or unequal with access door 75mm dia, type 'B' fixed in repairs complete all as specified and as directed.

All as per Sl Item No. 1.056 here in before but 110 mm dia. .

PVC (SWR) junction single (single Y) equal or unequal with access door 110mm dia, type 'B' fixed in repairs complete all as specified and as directed.

All as per Sl Item No. 1.058 here in before but 75 mm dia.

PVC (SWR) junction double (double Y) equal or unequal with access door 110mm dia, type 'B' fixed in repairs complete all as specified and as directed.

All as per Sl Item No. 1.060 here in before but 75 mm dia.

PVC (SWR) vent cowl of bore 75 mm dia, type 'B' including taking down old PVC vent cowl all as specified and as directed.

All as per Sl Item No. 1.062 here in before but 110 mm dia. .

20mm dia Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed(Min weight 20mm-210 gms) all as specified and as directed.

Gun metal gate or globe valves 25 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete including taking down old gate valve all as specified and as directed.

Dismantling water tanks and removing to store (exc. 250 and not exc. 500 ltr capacity) complete all as specified and as directed.

Dismantling water tanks and removing to store (exc. 500 and not exc. 1000 ltr capacity) complete all as specified and as directed.

Dismantling water tanks and removing to store (exc. 1000 and not exc. 2000 ltr capacity) complete all as specified and as directed.

Rotational moulded polythene water storage tank (cylindrical vertical with closed top) with ISI mark embosed on it, hoisted and fixed in position complete all as specified in SSR part I capacity of tank 500 ltrs capacity complete all as specified and as directed.

Rotational moulded polythene water storage tank (cylindrical vertical with closed top) with ISI mark embosed on it, hoisted and fixed in position complete all as specified in SSR part I capacity of tank 1000 ltrs capacity complete all as specified and as directed.

Rotational moulded polythene water storage tank (cylindrical vertical with closed top) with ISI mark embosed on it, hoisted and fixed in position complete all as specified in SSR part I capacity of tank 2000 ltrs capacity complete all as specified and as directed.

Providing and laying water proofing treatment to sunken portion of WCs, bathroom and kitchen etc by applying cement slurry mixed with two component elastomeric acrylic based polymer modified cementitious composite compound coating of make as approved in TI 5/2003 including demolition and removal of existing treatment of any type with the following procedure in sequence all as specified and as directed:- (i) Demolition of existing treatment of any type including cleaning and removal of debris from site. (ii) First layer of cement slurry @ 0.488 kg/sqm of cement mixed with acrylic based polymer modified cementitious composite compound @ 0.253 kg/sqm, the layer will be allowed to air cure for 4 hours. (iii) Second layer of cement slurry @ 0.242 kg/sqm of cement mixed with with acrylic based polymer modified cementitious composite compound @ 0.126 kg/sqm, the layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (iv) 20mm thick screed in cement mortar (1:3) mixed with including supply of liquid water proofing compound as per manufacturers instructions. Contd.. 1.073

1.072 Contd..(v) Ponding the treated portion atleast 48 hours, if any leakage / seepage observed the entire procedures will be repeated without any extra cost. (vi) Provide 40mm dia light grade GI spout at the lowest point with 30cm projection beyond the out face of the wall. (vii) Sunken portion shall be filled with lean cement concrete(1:5:10), type E-2 using 40mm graded stone aggregate. NOTE :- (i) The sunken slab sloped towards outer face to drain the water in to GI spout pipe. (ii) Coving shall be provided at the junction of slab with the wall. (iii) Nahni trap shall be 10mm below finished floor level and drain pipe dia is larger than the nahni trap size. (iv) The outer end of the spout should be chamfered.

Material and labour for cleaning of PVC/RCC over head water tanks at any height (on accessable / inaccessable roofs) by removing all scale, dirt, mud, any foreign material, accumulated silt, other dirty substance, algae, fungus and any other bacterial material from sides/bottom of tank, cleaning shall be done by draining / pumping out water / sludge from bottom, by high pressure water jet of pressure rating not less than 120 PSI for removing clogged mud/scales etc and cleaning the same again with self priming pumped fresh water and disinfecting the water tank by using UV radiator and approved chemical (chlorite), after cleaning writing letters / figures (Date of cleaning and next Date of cleaning) on black back ground with white synthetic enamel paint including removing the existing letters/ figures complete all as specified and as directed for capacity of water tank exc. 250 litre and n.exc. 500 ltr capacity complete all as specified and as directed. NOTE FOR SL ITEM NO. 1.074 to 1.076:- (i) Contractor has to ensure that there is no damage / leakage in tank after cleaning . (ii) Any air lock /blockage of water flow after cleaning will be made good immediately.

All as per Sl Item No. 1.074 above but capacity exc. 500 litre and n..exc. 1000 litre.

All as per Sl Item No. 1.074 above but capacity exc. 1000 litre and n..exc. 2000 litre.

Material and labour for spraying antiweed / non toxic solution / chemicals containing Glyphosate as per manufacture instructions and removing the weed including the roots after ensuring complete de-germification of palnt/weed and cutting down the plant/trees off from roof/top sides of external walls of bldgs, in chajjas, wall junctions, junctions of GI/CI/AC/PVC pipes and taking out roots entered in wall/slabs, including making good the surface using PCC (1:2:4) type B1 or brick work in CM(1:4) plastered with CM(1:4) to match with existing surface and repairing the pipes and joints which was affected by cutting down/taking out process all as specified and as directed for plants / trees located in the buildings upto four storey high, complete all as specified and directed by Engineer-in-charge. NOTE:- Contractor has to execute the work of de-generated plant/weeds as per the prior approval and directions of Engineer-in-charge.

All as per Sl Item Nno 1.077 here in before but plants located in the buildings of five to eight storey high.

Cleaning the roof /terrace of surface area exceeding 200 sqm but not exceeding 400 sqm at any height (on accessible/inaccessible roofs) by removing all scale, dirt, mud, any foreign material, accumulated silt, other dirty substance, algae, fungus, leaves etc deposited over slab and making good the distrubed surfaces if any, with and including making good the surface using PCC (1:2:4), type B1 or cement mortar (1:2) or brick work in CM(1:4) plastered with CM(1:4) to match with existing surface and removing the material so obtained out side MD land complete all as specified and directed by Engineer-in-charge. NOTE:- Contractor has to submit the phtographic record of work done (before and after the work done duly noted the building No along with location) at the time of claiming the payment (RAR/final bill). No payments shall be be made without submit the photographic records.

All as per Sl Item No. 1.079 here in before but surfce area exc. 400 sqm but not exc. 500 sqm.

All as per Sl Item No. 1.079 here in before but surfce area exc. 500 sqm but not exc. 800 sqm.

Aluminium anodised barrel towel bolts of extruded section of length 150 mm including taking down old unserviceable barrel tower bolts all as specified and as directed.

Aluminium anodised barrel towel bolts of extruded section of length 200 mm including taking down old unserviceable barrel tower bolts all as specified and as directed.

Aluminium anodised barrel towel bolts of extruded section of length 75mm including taking down old unserviceable barrel tower bolts all as specified and as directed.

300mm long Aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete including taking down old sliding door bolt all as specified and as directed.

Aluminium alloy extruded handles fabricated type anodised of size 100 mm long including taking down old handles all as specified and as directed.

Aluminium alloy extruded handles fabricated type anodised of size 150 mm long including taking down old handles all as specified and as directed.

Mild steel Butt hinges, medium weight, cold rolled of size 100mm fixed in repairs complete all as specified and as directed.

Hasp and staple safety type of size 100 mm of aluminium anodized fixed in repairs complete all as specified and as directed.

Mortice lock with two lever brass body 100mm size suitable for 25 to 60mm thick doors including screwing and fixing including taking down the existing complete all as specified and as directed.

40 mm dia cupboard knobs of brass, polished, fixed with nut, screw and washers including taking down the existing complete all as specified and as directed.

150 mm long floor door stopper of aluminium alloy powder coated, with hard down steel spring including taking down the existing complete all as specified and as directed.

Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.18 mm fixed with MS screw and bolts fixed in repairs complete all as specified and as directed.

Door closer hydraulically regulated designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg of aluminium (Die cast body) fixed in repairs complete all as specified and as directed.

Mild steel ordinary rat tail rod pattern springs 300mm long, including roller and roller plate fixed in repairs complete all as specified and as directed.

125mm size rim latch with two lever of mild steel body, stove enamelled finish, lever handle and fixed to steel windows, left and right, fixed in repairs complete all as specified and as directed.

Mild steel casement stays,size 300mm,with hinged joint and two plates, with studs fixed in repairs complete all as specified and as directed.

Curtain rods, Mild steel, Chromium plated with fixing brackets fixed in repairs complete all as specified and as directed.

Drapery rod of high strength aluminum rod powder coated thickness 40-60 micron of outer dia 28mm & ineer dia 24.5mm with providing 2 Nos brackets(projected type/wall to wall) and finials as approved by GE fixed in repairs complete all as specified and as directed. (Make : MAC-Sleek line type II/ Vista Levolor Soffio-II)

Ball catches with 8mm dia steel ball, brass body with striking plate including letting in and fixed in repairs complete all as specified and as directed.

4 mm thick figured glass, pin head type and glazing with oil putty in squares n.exc 0.5 Sqm in each pane including hacking out old broken glass of any thickness, size, quality or description from metal frame including punching or drilling out old glazing pins/spring clips etc complete all as specified and as directed.

3mm thick sheet glass, ordinary quality and glazing with oil putty in squares n.exc 0.5 sqm in each pane all as specified and as directed.

Resecuring or easing and adjusting without taking down shutters of any description area exc. 1 sqm but n.exc. 2 sqm each complete all as specified and as directed.

Kitchen sink with drain board overall size 915x460mm, bowl size 410x330x160mm made out of stainless steel 1mm thick with plugs, washers and waste including bedding in mortar on to dwarf wall, fixing cantilever brackets and connecting union pipes complete in repairs including taking down the existing sink complete all as specified and as directed.

Kitchen sink made of stainless steel 1mm thick with plugs, washers and waste, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets or fixing in granite slab and connecting union to pipe overall size 495mm x 420mm bowl size 410mmx 330mm x 160mm complete fixed in repairs all as specified and as directed.

Stainless steel plate rack made out of of 0.63mm thick stainless steel sheet, over all size 800mm x 600mm with shape, capacity of utensiles and pattern complete all as specified and as directed.

Plastic water closet seat cover, coloured, for pedestal pan closed pattern with flat bottom,and cover with mild steel chromimium plated or aluminised hinging device complete fixed in repairs all as specified and directed.

Brass CP wall mixer for mixing hot and cold water screwed down for iron pipe all as per Prayag Cat No-PIS-80H or equivalent makes specified in PS fixed in repairs complete all as specified and directed.

Brass CP sink mixer for mixing hot and cold water screwed down for iron pipe all as per Prayag Cat No-PIS-55H or equivalent makes specified in PS fixed in repairs complete all as specified and directed.

Brass CP central hole basin mixer for mixing hot and cold water screwed down for iron pipe all as per Prayag Cat No-PIS-50H or equivalent makes specified in PS fixed in repairs complete all as specified and directed.

Pillar taps, 15mm dia, swan neck type, cast copper alloy, chromium plated, screwed down, screwed for iron pipe all as per Prayag Cat No PIS-14H or equivalent makes specified in PS fixed in repairs complete all as specified and as directed.

15mm dia angle cock, chromium plated, cast copper alloy screwed down high pressure with capstan head handle screwed both ends or for unions etc., all as per Prayag Cat No PIS-10H or equivalent makes specified in PS fixed in repairs complete all as specified and as directed.

Health faucet, brass body with 1mtr SS braided tube and wall hook all as per Prayag Cat No. BEA-41/BEA-85 or equivalent makes specified in PS fixed in repairs complete all as specified and as directed.

Towel rail, stainless steel glossy finish all as per Prayag Cat No. BA10S or equivalent makes specified in PS fixed in repairs complete all as specified and as directed.

PVC Mirror cabinet of size 400x500 mm all as per Prayag Cat No. 554 or equivalent makes specified in PS fixed in repairs complete all as specified and as directed.

Health faucet, PVC body with 1.5mtr tube all as per Prayag Cat No. 188 or equivalent makes specified in PS fixed in repairs complete all as specified and as directed.

PTMT waste coupling of 32 mm dia, half or full threaded, [Minimum weight for 32 mm – 45 gms] fixed in repairs complete all as specified and as directed.

PTMT waste coupling of 40 mm dia, half or full threaded, fixed in repairs complete all as specified and as directed.

Grating doom type, 100 mm dia with waste hole all as per Prayag Cat No. FT-04M or equivalent makes specified in PS fixed in repairs complete all as specified and as directed.

25mm dia Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed all as specified and as directed.

Atom Engineers and Builders