Development of New Parks/Green Belts.

SCHEDULE-A Excavating holes more than 0.10 cum & up to 0.5 cum including getting out the excavated soil, then returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto1.5 m. a)All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : a)1:1½:3 (1 Cement: 1½ coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Providing and fixing "Air Walker" with the specifications below: 1. Dimensions (LxWxH): 1100 x 450 x 1300mm. 2. Fabricated with main post of NB 100mm (G.I.) "C" Class Pipe of approved make. 3. U-shaped main frame of NB 80mm (G.I.) "C" Class Pipe, Leg Support frame of NB 50mm (0.1) "C" Class Pipe. 4. Handy frame pipes of NB 32mm (G.I.) "C" Class (NB stands for Nominal Bore i.e., Internal Diameter of pipe in millimetres). 5. All pipes are powder-coated with 80–120-micron thick AkzoNobel or equivalent paints. 6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Baseplate cover made of virgin LLDPE plastic by rotational molding with a minimum of 4.00mm thickness, UV resistant and coloured. 9. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury. 10. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured. 11. The equipment must be fitted with inbuilt limiters to prevent unwanted movements. 12. The equipment is to be fixed on the ground by providing and laying Cement Concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness. 13. High tensile steel with galvanized nut bolts is used for assembly. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with a baseplate cover. 15. Equipment made to G5 Mark, EN16630, DIN 79000 & 150 14001 International standard for outdoor fitness equipment. 16. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years. 17. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra.

Providing and fixing "Horse Rider Station" with the specifications below:1. Dimensions (LxWxH): 1000 x 600 x 1100 mm.2. Fabricated with main post of NB 100mm (G.I.) "C" Class Pipe of approved make.3. Main frame of NB 65mm (G.I.) "C" Class Pipe. 4. Handle support frame of NB 50mm (G.I.) "C" Class Pipe and other pipes of 4 NB 32mm & NB 25mm (G.I.) "C" Class Pipe. ('NB' stands for Nominal Bore i.e., Internal Diameter of pipe in millimetres).5. All pipes are powder-coated with 80–120-micron thick AkzoNobel or equivalent paints.6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing.8. Baseplate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and coloured.9. Foothold made of NB 32mm (G.I.) "C" Class Pipe. 10. Seat to be made up from virgin LLDPE manufactured by rotational moulding with 4.00 mm thickness, coloured, UV resistant and environmentally friendly.11. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured. 12. The equipment must be fitted with inbuilt limiters to prevent unwanted movements.13. The equipment is to be fixed on the ground by providing and laying cement concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.14. Once the concrete is set, the equipment is fixed on to it and the nuts and bolts are covered with a baseplate cover. 15. High tensile steel with galvanized nut bolts is used for assembly.16. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. 17. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years.18. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra.

Providing and fixing "Leg Press" in a pair with the below specifications: 1. Dimensions (LxWxH): 2000 x 550 x 1600 mm. 2. Fabricated with main post of NB 100mm (G.I.) "C" Class Pipe of approved make. 3. Seat Main frame of NB 50mm (G.I.) "C" Class Pipe and Pipe connecting main post to seat main frame of NB 65mm (G.I.) "C" Class Pipe. ('NB' stands for Nominal Bore i.e., Internal Diameter of pipe in millimetres). 4. All pipes are powder-coated with 80–120-micron thick AkzoNobel or equivalent paints. 5. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs. 6. Zinc primer paint is applied at all the welding points prior to finishing. 7. Baseplate cover made of virgin LLDPE plastic by rotational molding of 4.00mm thickness, UV resistant and coloured. 8. Foothold is made of NB 50mm (G.I.) "C" Class Pipe. 9. Seats made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, are coloured, UV resistant and environmentally friendly. 10. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured. 11. The equipment must be fitted with inbuilt limiters to prevent unwanted movements. 12. The equipment is to be fixed on the ground by providing and laying cement concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness. 13. Once the concrete is set, the equipment is fixed on to it and the nuts and bolts are covered with a baseplate cover. 14. High tensile steel with galvanized nut bolts is used for assembly. 15. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. 16. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years. 17. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra.

Providing and fixing "Pull Chair' in a pair with the below specifications: 1. Dimensions (LxWxH): 2400 x 800 x 2000 mm. 2. Fabricated with main post of NB 100mm (G.L.) "C" Class Pipe of approved make. 3. Seat main frame of NB 50mm (G.L.) "C" Class Pipe, Pipe connecting main post with handle frame of NB 65mm (GL) "C" Class Pipe. 4. Handle frame of NB 32mm (G.L.) "C" Class Pipe. ("NB" stands for Nominal Bore i.e., Internal Diameter of pipe in millimetres). 5. All pipes are powder-coated with 80–120-micron thick AkzoNobel or equivalent paints. 6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Handle bars are provided with high-end quality rubber grips. 9. Baseplate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and coloured. 10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, coloured, UV resistant and environmentally friendly. 11. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured. 12. The equipment must be fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is to be fixed on the ground by providing and laying cement concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with a baseplate cover. 15. High tensile steel with galvanized nut bolts is used for assembly. 16. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. 17. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years. 18. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra.

Providing and fixing "Seated Chest Press" in a pair with the below specifications:1. Dimensions (LxWxH): 1800 x 700 x 2000 mm.2. Fabricated with main post of NB 100mm (G.I.) "C" Class Pipe of approved make. 3. Seat Main frame of NB 50mm (G.I.) "C" Class Pipe.4. Handle frame of NB 32mm and NB 25mm (G.I.) "C" Class Pipe.('NB' stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimetres).5. All pipes are powder-coated with 80–120-micron thick AkzoNobel or equivalent paints.6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing.8. Handle bars are provided with high-end quality rubber grips. 9. Baseplate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and coloured.10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, coloured, UV resistant and environmentally friendly. 11. Maintenance-free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.12. The equipment must be fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is to be fixed on the ground by providing and laying cement concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with a baseplate cover.15. High tensile steel with galvanized nut bolts is used for assembly.16. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.17. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years.18. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra.

Providing and fixing an "Arm Wheel" in a pair with the below specifications: 1. Dimensions (LxWxH): 850 x 800 x 1800 mm. 2. Fabricated with main post of NB 100mm (G.I.) "C" Class Pipe of approved make. 3. Wheel frame of NB 32mm with connecting spokes of NB 25mm, Pipe connecting main pilar with wheel frame of NB 50mm. All pipes must be (G.I.) "C" Class Pipes ('NB' stands for Nominal Bore Size, i.e., Internal Diameter of pipe in millimetres). 4. All pipes are powder-coated with 80–120-micron thick AkzoNobel or equivalent paints. 5. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs. 6. Zinc primer paint is applied at all the welding points prior to finishing. 7. Baseplate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and coloured. 8. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured. 9. The equipment is to be fixed on the ground by providing and laying Cement Concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J shaped welded bolts of 18mm thickness. 10. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with a baseplate cover. 11. High tensile steel with galvanized nut bolts is used for assembly. 12. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. 13. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years. 14. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra.

Providing and fixing "Double Cross Walker "with the specifications below: 1. Dimensions (LxWxH): 1600 x 600 x 1600 mm. 2. Fabricated with main post of NB 100mm (G.I.) "C" Class Pipe of approved make. 3. Handle main frame of NB 50mm and other connecting pipes of NB 32mm and NB 25mm (G.I.) "C" Class Pipe. ('NB' stands for Nominal Bore Size, i.e., Internal Diameter of pipe in millimetres). 4. Foot support frame of 96 x 46 x 3mm MS rectangular pipe. 5. All pipes are powder-coated with 80–120-micron thick AkzoNobel or equivalent paints. 6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Baseplate cover made of virgin LLDPE plastic by rotational molding with a minimum of 4.00mm thickness, UV resistant and coloured. 9. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury. 10. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured. 11. The equipment must be fitted with inbuilt limiters to prevent unwanted movements. 12. The equipment is to be fixed on the ground by providing and laying Cement Concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J shaped welded bolts of 18mm thickness. 13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with a baseplate cover. 14. High tensile steel with galvanized nut bolts is used for assembly. 15. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. 16. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years. 17. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra.

Providing and fixing "Triple Twister" with the specifications below: 1. Dimensions (LxWxH): 1300 x 1300 x 1650 mm. 2. Fabricated with main post of NB 100mm (G.I.) "C" Class Pipe of approved make. 3. Handle Main frame of NB 32mm (G.I.) "C" Class Pipe. 4. Handle frame spokes of NB 25mm (G.I.) "C" Class Pipe. ('NB' stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimetres). 5. Foothold plate made of MS Sheet Metal of 3mm thickness. 6. All pipes are powder-coated with 80–120-micron thick AkzoNobel or equivalent paints. 7. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs. 8. Zinc primer paint is applied at all the welding points prior to finishing. 9. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured. 10. The equipment is to be fixed on the ground by providing and laying cement concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness. 11. Once the concrete is set, the equipment is fixed on to it. 12. High tensile steel with galvanized nut bolts is used for assembly. 13. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. 14. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years. 15. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra.