PROVN OF 01 URINAL BLOCK HAVING 20 X URINAL POINT AT NO 2 TRG BN OF AOC CENTRE, ADDN / ALTN AND SPL REPAIRS TO BLDG NO 6,6A AND 6B OF 125 INF BN (TA) UNDER AGE B/R (SOUTH) NO-I AND II OF GE (SOUTH) SECUNDERABAD

Amount

S&F Pre painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws incl dismantling of old AC corrugated or semi corrugated roof sheets complete all as specified and directed.

S&F Pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strengh of 550 mpa as on roof covering/ridges fixed with self tapping screws incl dismantling of old AC corrugated or semi corrugated roof sheets complete all as specified and directed.

Dismantling timber scantlings in unframed work 40 sq. cm and over in section fixed in any position complete all as specified and directed.

Dismantling of wall and ceiling boards ( fiber pulp insullation etc ) or insullation boards / slabs, blankets any thickness including cover fillets complete all as specified and directed.

S&F in repairs anodised aluminium snap grid frame work for false ceiling including supporting wire all as specified of size of grid 605 x 605mm complete all as specified and directed.

S&F 4mm thick non-asbestos fibre cement building boards fixed or laid/inserted to aluminium / wooden frame work with screws including two coats of OBD over a coat of alkali resistant primer and preparation of new surfaces of ceiling complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) not exceeding 1.5 Sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exceeding 1.5 Sqm but n exc 4 sqm each complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with M S Square tube, in opening as per manufacturers instructions complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails .M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail ,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/scaled to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement and fixing in the frame as per manufacturers instructions complete all as specified and directed.

S&F factory made 35mm thick 2nd class hard wood, plain framed, paneled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both sides, the side of rail and stile as per IS-1003(Part-I), kiln seasoned and chemically pressure treated , 35 mm thick complete all as specified and directed.

S&F second class hard wood 35mm thick glazed and skelton shutters divided into squares with plain, chamfered or rounded, mitred and with out sash bars prepared to receive glass, gauge sizes of members of shutters as specified in SSR Pt-I, section 8 , clause 8.24 (A) complete all as specified and directed.

S&F 100 mm long butt hinges extruded aluminium alloy with galvanised mild steel hinge pin type C-21 anodised complete all as specified and directed.

S&F for aluminium alloy anodised sliding door bolt with hasp staple (bolt type) length 300mm complete all as specified and directed.

S&F 200mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F 150mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F for aluminum handles fabricated type anodised 150 mm complete all as specified and directed.

S&F for floor door stoper of aluminium alloy body of 150 mm long complete all as specified and directed.

S&F for Mild steel helical door spring 300 mm long complete all as specified and directed.

M&L for preparation of new wooden surfaces and applying two coats of synthetic enamel paint over a coat of pink primer exceeding 10 cm width or girth complete all as specified and directed.

M&L for complete removal or existing wall treatment of old surfaces and applying two coats of oil bound distemper over a coat of cement primer including preparation of 3mm thick wall care putty surfaces complete all as specified and directed.

M&L for complete removal of existing treatment of old wall surfaces surfaces and applying two coats of weather proof exterior emulsion paint over a coat of primer on wall surfaces complete all as specified and directed.

M&L for complete removal of existing treatment of old wall surfaces and applying one coat of white wash complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. complete all as specified and as directed.

S&F granite work of any type 20mm thick (of any type) work table rubbed & polished in steps , jambs , pillar, widow cills, cooking platforms and laid over 15mm thick screed bed or bedding in layer of in CM 1:4 for laying floor finishes incl pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite complete all as specified and directed.

Rounding to edges of stone slabs one edge such as in slopes cooking platform and other similer shine complete all as specified and directed.

S&F Stainless steel wire cloth, 0.36 mm dia of wire and average width of aperture 1.40 mm and fixed with stainless wire staples in repairs complete all as specified and directed.

S&F 12 mm thick prelaminated particle board interrior grade prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with glazing clips complete all as specified and directed.

S&F in repair 2nd class hard wood in fillets,square, rectangular in section wrought, secured with nails sectional area exc 13 Sqcm and n.exc 25 Sqcm complete all as specified and directed.

S&F hasp & staple 100mm size aluminium anodised fixed with screws complete all as specified and directed.

S&F continous (Piano) hinges , mild steel, bright finished or electrogalvanised width of flaps in 30mm complete all as specified and as directed.

S&F 40mm dia cupboard knobs fixed with nuts screws and washers of brass polished of approved quality complete all as specified and directed.

S&F in repair stainless steel sink made out of 1.00 mm thick sheet for kitchen with plug and washers, waste pipe with cantilever brackets.over all size 495 X 420mm bowl size 410mm X 330mm X160mm complete all as specified and directed.

Demolition of cement concrete in floors and pavings n.exc15 cm thickness (below or above ground level) including floor finishes etc complete all as specified and directed.

M&L for 25 mm thick plain cement concrete type B0 (1:2:4) ( 12.5 mm graded stone aggregate ) as in floors complete all as specified and directed.

S&F Vitrified ceramic tiles light shade 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding in layer of CM 1:6 for laying floor finishes complete all as specified and directed.

S&F Vitrified ceramic tiles light shade 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, as in skirtting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick bedding in layer of CM 1:4 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

S&F glazed ceramic coloured tiles 450x300x7mm thick on vertical surfaces such as dados set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

S&F powder coated anodised aluminium frame,three track sliding for windows, fixed/top hung frame for ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F powder coated anodised aluminium sliding window shutter and top hung ventilator shutters with sash bars aluminium sections weighing 0.55kg/m including necessary joining cleats, glazing clips rubber packing,locking arrengement complete all as specified and directed. Note:- Glass panes and wire mesh shall be measured and paid seperately)

Demolition and beaking up drain AC pipes/PVC pipes/CI Pipes set in cement mortar of any dia and size complete all as specified and directed.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls bore of the pipe 110 mm complete all as specified and directed.

S&F PVC (SWR) bends 110 mm complete all as specified and directed.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls bore of the pipe 75 mm complete all as specified and directed.

S&F PVC (SWR) bends 75 mm all complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) junction single ( single 'T') equal or unequal complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) Vent Cowl complete all as specified and directed.

S&F110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fix to walls complete all as specified and directed.

S&F PVC (SWR) bends any radius 75mm bore with access doors complete all as specified and directed.

S&F PVC (SWR) Vent cowls of bore 110mm complete all as specified and directed.

S&F GI pipe medium grade 15 mm dia with all fitting laid in floor or fixed in walls including taking down old GI tubes complete all as specified and directed.

S&F GI pipe medium grade 20 mm dia with all fitting laid in floor or fixed in walls including taking down old GI tubes complete all as specified and directed.

Excavating in trenches n.exc 1.5m wide and n.exc 1.5m depth for foundation etc or wells cess pits manholes n.exc 10 Sqm on plan and getting out in Hard and dense soil complete all as specified and directed.

Excavating over areas and getting out hard/dense soil exc 1.5m and n. exc 3.0 m deep complete all as specified and directed.

Returning filling in including spreading, levelling watering and well ramming in layers not exc 25cm thick complete all as specified and directed.

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

M&L for cement concrete type D 2 1:4:8 (using 40 mm graded crushed stone aggregate) in foundation filling and mass concrete complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia for securing with clips quality conforming to deformed or TMT bars complete all as specified and directed.

Ditto as per item no-54 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders TMT bars complete all as specified and directed.

M&L for Form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc also splays between floors and beams, etc.rough finished surfaces of concrete complete all as specified and directed.

M&L for Reinforced cement concrete (nominal mix) in type B1 1:2:4 (20 mm graded stone aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for broken stone or boulder hard core of gauge exc63 mm but n exc 100mm deposited spread and levelled in layers n,exc 15 cm thick watered and rammed to true surface complete all as specified and directed.

S&F Rolled sections as in main and cross beams, hip and jack rafters, truss, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or coneecting plates Fe 410-W (Gde E 250) Quality - A complete all as specified and directed.

M&L for Damp proof course 40mm thick of PCC type B0 1:2:4(using 12.5mm graded crushed stone) complete all as specified and directed.

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in, built in CM (1:6) Complete all as specified and directed.

M&L for Brickwork with fly ash bricks, straight or curved on plan exc to any radius, half brick walls, built in CM (1:4) Complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8 type D2 (using 40mm graded crushed stone aggregate) as in sub bases, sub flooring finished even and rough complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C2 (using 40mm graded crushed stone aggregate) as in plinth protection finished even and smooth without using extra cement complete all as specified and directed.

M&L for 25 mm thick Cement concrete type B-1 1:2:4 (using 20mm graded crushed stone aggregate) as in floor base complete all as specified and directed.

M&L for Rendering 10mm thick in CM( 1:6) on fair faces of brick work or concrete surfaces finished even and fair without using extra cement complete all as specified and directed.

M&L for Rendering 15mm thick in CM (1:4) finished even and fair without using extra cement complete all as specified and directed.

S&F Figured glass, pin head type 3mm thick and glazing with aluminium glazing clips in square n.exc 0.5 sqm in each pane complete all as specified and directed.

S&F glazed ceramic coloured tiles of size 300x450x7mm thick in vertical surfaces of wall set and jointed in neat cement slurry and pointed in coloured cement to match including 10mm thick rendering in CM (1:3) backing complete all as specified and directed.

S&F Non skid coloured ceramic tiles300x300mm x 7 to 8mm) thick, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM (1:6) complete all as specified and directed.

S&F Chequered cement concrete tiles of size 200x 200x25mm thick set, jointed and ointed in neat cement slurry in floors with grey cement and no pigmnet to match with the colour of tiles over and including 20mm thick screed bedding layer in cement mortar 1:6 complete all as specified and directed.

S&F of factory made solid PVC moulded shutter with 28 to 30mm thick(stiles)with 2,4 or 6 raised panel design with 2mm thick moulded PVC prelam sheet on the front face and 2mm thick plain colour PVC sheet on back face with particle board core complete all as specified and directed.

S&F of extruded aluminium handles fabricated type anodised 100mm complete all as specified and directed.

S&F 15 mm dia Tubes'Medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F 20 mm dia Tubes, 'Medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F 15 mm Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F for Stop valves,cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

M&L for preparation of newly plastered surface of wall and applying two coats of cement base paint over and including a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil emulsion distemper over and including a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation of new steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over and including a coat of zinc chrome primer complete all as specified and directed.

S&F PVC valveless syphonic action type flushing cistern 10 lit capacity low level white with inlet, ball valve, float and handle including brackets and 32mm PVC flush pipe complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F 15mm bore pillar taps, fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F Towel Ring of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats ( Min wt 90 gms) complete all as specified and directed.

S&F Towel Rail 600 mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats ( Min wt 190 gms) complete all as specified and directed.

S&F Vitreous china wash basin, white, flat back, size 550x400 mm excluding ditto but including brackets, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed.

S&F Vitreous China Urinal, Half stall type, white complete including providing and fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with 60 mm long brass screws, pointing around urinal back in cement, including all fittings cistern, brackets, flush pipe, spreader, push tap, waste coupling, grating, etc Complete set incl all fitting & fixtures complete all as specified and directed.

S&F Vitreous china urinal partition white of size 310x700 mm terminating about 40 cm above floor line complete all as specified and directed.

S&F Vitreous china Squatting pan Orissa pattern of size 580mx440mm wite with integral foot rests (excluding flushing cistern and flush pipe) complete including concrete bedding complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks 1000 ltrs(cylindlerical vertical with closed top) hoisted and fixed in position all as specified in SSR part I complete all as specified and directed.

S&F in repairs 20 mm dia gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

S&F 20mm bore Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weigth 455gms) complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface in hard or dence soil complete all as specified and directed.

M&L for SWG drain pipe grade 'A' of 150 mm internal dia laid in trenches and jointed in cement mortar 1:1 complete all as specified and directed.

M&L for concrete bed to drain pipes 150mm dia using cement concrete 1:3:6 type C2 including packing under and haunching against the sides of pipes after they are laid and tested in complete all as specified and directed.

M&L Precast reinforced cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregate ) for manhole cover septic tank covers slabs etc including necessary form work and set in CM (1:4) complete all as specified and directed. (Note:- Reinforcement will be measured and paid separately under relevant item)

Taking down existing unserviceable point wiring of any description/type/ size of light/ fan/tube/power/two way/bell point etc on TW batten/conduit including removal of batten / conduit / gutties / wooden boards / switches / sockets / regulators/ light fittings etc and removal of unserviceable material out of site and making good the disturbed surfaces of wall/ceiling so as to match with the existing finishes complete all as specified and directed.

M&L for Point wiring complete with two runs of 1.5 Sq mm copper conductor (for Phase and neutral) PVC insulated unsheathed multi stranded ,copper conductor FRLSH cable of 1100V grade confirming to IS- 694 drawn through and including new non metallic rigid PVC conduit medium grade , ISI marked , 20 mm bore with conduit accessories surface mount on wall or fixed on ceiling/roof/truss/columns etc,including provision of fabricated branded pressed steel terminal box of suitable sizes with 1.6mm thickness duly painted inner and outer side by anti corrosive paint for housing the modular switches,sockets,fan regulators etc and covered with 3mm thick steel plates complete concealed in walls and provn of 1.5 Sqmm PVC insulated unsheathed copper conductor cable of green colour to common earth dolly etc. complete all as specified and as directed for one light point controlled by one switch complete all as specified and directed. Note: The wiring shall be done in proper color coding using red,yellow,blue for phases , black for neutral and green for earth

All as per item No-105 above but for one ceiling / exhaust fan point controlled by one, one way switch

All as per item No-105 above but for one 2/3 pin 5 Amps switch socket outlet point controlled by one switch on the same board

All as per item No-105 above but for one 3 Pin 5 Amps switch socket Independt board

Description all as per item No 105 here-in-before but using 4 Sq mm single core copper conductor cable of multistranded PVC insulated FRLS 1100 Volts grade for 5/15 Amps switch socket combination point including running of 4 Sq mm copper conductor PVC wire as earth continuity conductor along with wiring and connecting to the common earth dolly.

M&L for Point wiring complete with two runs of 1.5 Sq mm copper conductor (for Phase and neutral) PVC insulated unsheathed multi stranded ,copper conductor FRLSH cable of 1100V grade confirming to IS- 694 drawn through and including new PVC casing caping , ISI marked , including provision of fabricated branded pressed steel terminal box of suitable sizes with 1.6mm thickness duly painted inner and outer side by anti corrosive paint for housing the switches,sockets,fan regulators etc and covered with 3mm thick plastic laminated sheet cover with cadmium plated screw ,cup washer etc. complete concealed in walls and provn of 1.5 Sqmm PVC insulated unsheathed copper conductor cable of green colour to common earth dolly etc. complete all as specified and as directed for one light point controlled by one switch one way switch 5A, SP complete all as specified and directed. Note: The wiring shall be done in proper color coding using red,yellow,blue for phases , black for neutral and green for earth.Modular cover plate with frame, flush box will be inclusive of rate quoted.

All as per item No-110 above but for one ceiling / exhaust fan point controlled by one, one way switch

All as per item No-110 above but for one 2/3 pin 5 Amps switch socket outlet point controlled by one switch on the same board

All as per item No-110 above but for One 3 Pin 5 Amps switch socket Independt board

All as per item No-110 above but for One Bell point controlled by one, bell push

Description all as per item No 110 here-in-before but using 4 Sq mm single core copper conductor cable of multistranded PVC insulated FRLS 1100 Volts grade for 5/15 Amps switch socket combination point including running of 4 Sq mm copper conductor PVC wire as earth continuity conductor along with wiring and connecting to the common earth dolly complete all as specified and directed. Note: The wiring shall be done in proper color coding using red,yellow,blue for phases , black for neutral and green for earth.Modular cover plate with frame, flush box will be inclusive of rate quoted.

S&F single pole Modular switch 1 way 6 Amps, 1 Module complete all as specified and directed.

S&F single pole Modular switch 1 way 16 Amps, 1 Module complete all as specified and directed.

S&F socket outlet modular type multipurpose 2/3 Pin, 6 amps, 230 volts combined 2 Module complete all as specified and directed.

S&F socket outlet modular type multipurpose 3/5 Pin, 6/16 amps, 230 volts combined 2 Module complete all as specified and directed.

S&F Modular Bell Push 6A, 1 Module complete all as specified and directed.

S&F bell (buzzer/ding dong) working on 230 volts AC Supply

S & F Modular ceiling fan regulator stepped socket size (modular) suitable to work on 230 volts complete all as specified, 2 Module

S & F Switch piano type single pole one way flush type 5 Amps capacity 230 volts complete all as specified and directed.

S&F switch socket combination flush type multipurpose 2/3 pin 5 Amps, 230 Volts complete all as specified and directed.

S&F socket outlet flush type multipurpose 2/3 pin 5 amps, 230 volts complete all as specified and directed.

S&F switch socket combination flush type multipurpose 5 in 1, 5/16 Amps, 230 Volts complete all as specified and directed.

S&F ceiling fan regulator step socket type AC 240 volt suitable for 1200 mm sweep complete all as specified and directed.

S&F ceiling rose three terminal surface bakelite type AC 50 Hz 230 Volts of size 65 x 50 mm complete all as specified and directed.

S&F Vertical loadline type TPN DB 4 way double door with fixed magnetic setting for current rating of 100 Amps 16 KA (MCCB TP volts AC 3 phase 50 Hz ) confirming to IS specification made out of CRCA sheet housing duly powder coated & confirming to IS specification complete all as specified and directed.

S&F MCCB 415 V,16KA,100 A 4 pole suitable for DB including the existing unserviceable one and making good the disturbed surface to match with the existing surface complete all as specified and directed.

S&F sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 Volts double door with magnetic locking system complete all as specified and directed.

S&F sheet metal enclosure MCB DB SPN 4 way with 200 Amps rated bus bar 240 Volts double door with magnetic locking system complete all as specified and directed.

S & F MCB SPN 230V suitable for fixing on MCB DB of capacity 40 Amps complete all as specified and directed.

S& F MCB SP 230V suitable for fixing on MCB DB of capacity 6 to 32 Amps complete all as specified and directed.

S&F MCB SPN 230V suitable for fixing on MCB DB of capacity 63 Amps complete all as specified and directed.

M&L for Submain wiring with two single core 6 Sq mm PVC insulated cable FRLS type copper conductor multistranded 1100 Volts grade drawn through and including rigid PVC conduit and conduit accessories of 25 mm dia medium grade including running up of 6 Sq mm copper conductor multistranded PVC insulated cable as earth continuity conductor along the wiring and connected to the common earth dolly complete including removing the existing unserviceable sub main wiring and making good the disturbed surface to match with the existing complete all as specified and directed. Note:-two runs of cable, one run of earth contuinity conductor and one run of conduit shall be measured and paid as one unit length.

M&L for Submain wiring with two single core 4 Sq mm PVC insulated cable FRLS type copper conductor multistranded 1100 Volts grade drawn through and including rigid PVC conduit and conduit accessories of 25 mm dia medium grade including running up of 4Sq mm copper conductor multistranded PVC insulated cable as earth continuity conductor along the wiring and connected to the common earth dolly complete including removing the existing unserviceable sub main wiring and making good the disturbed surface to match with the existingcomplete all as specified and directed. Note:-two runs of cable, one run of earth contuinity conductor and one run of conduit shall be measured and paid as one unit length.

M&L Submain wiring with 2 runs of single core 10 sqmm PVC insulated FRLS multistranded 1100 volts grade wire, copper conductor drawn through and including non-metalic rigid PVC conduit and conduit accessories of medium grade not not less than 25mm dia including one run of single core 10 sqmm PVC insulated sheated multistranded 1100 volts grade with copper conductor cable as earth continuty conductor along with the wiring and connected from DB to DB/main board including removing the existing unserviceable submain riwing complete all as specified and directed. Note:-Two runs of cable, one run of earth contuinity conductor and one run of conduit shall be measured and paid as one unit length.

S&F wall mounted box type LED of 20 watt with LED Lamp, with 2 Nos round blocks with necessary fixing arrangements and connecting to the point wiring with necessary flexible copper conductor multistranded three core of suitable length & size from fitting to the ceiling rose complete all as specified and directed.

S&F wall mounted LED batten of 09 watt with LED Lamp complete all as specified and directed.

S&F 12 Watt LED Bulb complete all as specified and directed.

S&F lamp holder insulated body surface bakelite with back plate suitable for angle / batten fittings complete all as specified and directed.

S & F 36 watt recess softline luminaire (2x2) suitable for armstrong/grid ceiling with high brightness white LEDs and PMMA extruded diffuser giving glare free light and good aesthetic appeal and all including taking down complete all as specified and directed.

S&F wall mounted decorative light antique finish with IP 54 protection complete all as specified and directed.

M&L for Earthing complete with galvanised steel earth plate electrode 60cm x60cm x6mm thick buried directly in ground earth pit not less than 2.25 mtr deep with top edge of plate not less than 1.5m below ground level, connecting to the Galvanised iron earth earth lead 4 mm dia, by means of nuts, bolts, check nuts and washer etc of galvanised iron and earth lead protected by provision of GI pipe Light grade 15mm bore from earth elelctrode to test point incl provn of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone agagregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4Kg/Sqm) and frame of angle iron 25 x 25x6mm with lugs 2 Nos and with 6mm dia MS bar handle made to shape, GI pipe med grade 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, test point with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning in and removal of surplus soil to a distance not exceeding 50mtr, all as per electrical plate No 5 of Part-I and connection to earth test point all as specified incl testing on completion complete all as specified and directed. Note :- Item of Earthing includes cost of 7.5m long galvanised iron earth lead 4 mm size and protection pipe of 15 mm bore GI light grade.

Disconnecting and removing ceiling fan of 1200/1400 mm sweep any height from electrical connection bringing down, dismantling, cleaning internally and externally thoroughly examine and rewinding of the ceiling fan with equivalent new super enamelled copper wire of existing gauge and weight as per manufacturer's design and instructions including varnishing for ceiling fan complete including replacement of worn out/defective parts such as capacitor, sealed ball bearing, rubber bushes , split pins, cotter pins and check nuts etc overhauling, lubricating with approved lubricants, reassembling and refixing in original position with provision of new flexible wire of size 23/0.0076 multistranded copper conductor cable from ceiling rose to fan including painting of ceiling fan complete with synthetic enamel paint by spraying including filling cavities with filler , one coat after cleaning all dust etc & testing complete all as specified.

Disconnecting and removing Exhaust fan of 300/225 mm sweep any height from electrical connection bringing down, dismantling, cleaning internally and externally thoroughly examine and rewinding of the Exhaust fan with equivalent new super enamelled copper wire of existing gauge and weight as per manufacturer's design and instructions including varnishing for Exhaust fan complete including replacement of worn out/defective parts such as capacitor, sealed ball bearing, rubber bushes etc overhauling, lubricating with approved lubricants, reassembling and refixing in original position with provision of new flexible wire of size 23/0.0076 multistranded copper conductor cable from ceiling rose to fan including painting of Exhaust fan complete with synthetic enamel paint by spraying including filling cavities with filler , one coat after cleaning all dust etc & testing incl provision of metallic louver and HDPE high grade plastic net 800 GSM,hole size one inch,thickness 3mm green colour on the outside wall complete all as specified and directed.

S&F Single pole and Neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps (AC Box) complete all as specified and directed.

S&F Security Lights of 1x25 watt LED light with high power LED and unique peanut lens to ensure uniform distribution and including provision of 1.5 sqmm 3 core multistranded copper conductor cable from light fitting to junction box complete all as specified and directed.

M&L bracket made out of GI pipe of suitable dia not less than 1.2 mtr long and fixed on walls with 2 nos MS clamps made out of MS flat of suitable size thick complete with MS nuts, bolts and washers etc bent to required shape complete all as specified and directed.

S&F Exhaust fan of metal body 300 mm sweep with metallic louver including connecting up of PVC insulated copper conductor multi stranded cable of suitable size from ceiling rose to connector complete including provision of HDPE high grade plastic net 800 GSM,hole size one inch,thickness 3mm green colour on the outside wall complete all as specified and directed.

M&L for cutting of wall in round shape irrespective of height of building using machine cutting only and making opening suitable for mounting of 300 mm dia exhaust fan and making good disturbed surfaces matching with existing colour including grouting of nuts and bolts and clearing the debris and making the work area clean complete all as specified and directed. Note: Contractor to check the site requirement.

Supply & lay on wall / in ground / on pole XLPE insulated, armoured, heavy duty electric cables with stranded aluminium conductor, 1100 volts laid in trenches, ducts, pipes, drawn across the roads/paths/drains/along poles/walls/floors/equipment etc including jointing and testing complete all as specified and directed. of size 2 core 10 sqmm

Supply, spread river sand of approval quality sharp and angular free from organic matters in cable trenches providing for cable cushioning complete all as specified and directed. NOTE :- Punned thickness of 18cm after watering and compaction of sand only will be measured and paid.

Supply and Laying PCC cable covers for LT cable protection, Class LV, Type 1 of size 250x150x40mm

Supply and Laying 40 mm dia GI tubing light grade in protection of cable at roads crossing/hard standing/pole protection fixed with clamps as per site requirement etc complete all as specified and directed.

SAI RUPA CONSTRUCTIONS (BID ID -3086227)

GADUSU RAMESH CONTRACTOR (BID ID -3090584)

ATUL ENTERPRISES (BID ID -3076478)

PARDEEP AND CO (BID ID -3090443)

RAGHAVENDRA CONSTRUCTIONS (BID ID -3087059)

SRI DHANESWARI ENGINEERING WORKS (BID ID -3088665)

BEEGEE DESIGN SYSTEMS (BID ID -3090390)