SPL REPAIR OF BLDG NO. P-473 AND P-26 AT SITE-III OF THE RAJPUT REGT CENTRE FATEHGARH

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (including taking down of backing plaster to brick / concrete wall surface), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete in ground floors and paving n exc 15 cm thickness (below or above ground level) complete all as specified and directed

M & L 25 mm thk cement conc. Type B-0 1:2:4 (12.5mm graded crushed stone aggregate) as in sub base to floor complete all as specified and directed

M&L for Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match , laid over & including 15mm thick cement screed bed or bedding layer in CM 1:6, etc. complete all as specified and directed

M & L for machine cut kota stone slab as in flooring 18-20 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and Mirror polishing on marble/ granite/Kota stone/ stone work where ever required to give high gloss finish complete over 20 mm thick screed bed in CM 1:6 complete all as specified and directed

M & L for Glazed ceramic tiles in vertical surface 450 x 350x 7mm thick coloured tiles, set and jointed in neat cement slurry and pointed in white or colour cement to match, over and inlcuding10 mm thick rendering on fair faces of concrete surface of verticle in CM (1:3) finished even and smooth without using extra cement complete, shade & design as approved by EIC/AGE (I), incl rubbish off the primises etc all as specified and directed.

M&L for non skid ceramic any coloured/printed tiles 7 to 8 mm thick (square/rectangular ) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm as in floor of shade & designed as approved by AGE (I),set and jointed in neat cement slurry and pointed with white cement with colour pigment to match the colour of tiles,over15 mm thick screed bed in cement mortar (1:4) in floors, incl dismantling / demolition and rubbish off the primises etc complete all as specified and directed.

M& L For providing Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors Complete all as speecified and directed

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed

M & L Rendering 15mm thick in CM (1:4) on fair faces of brick work or concrete surfaces to be finished even and smooth without using extra cement complete all as specified and directed

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces over 3mm thick wall care putty complete all as specified and directed

M&L for Rendering 15mm thick on brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying two coats of OBD complete all as specified and directed.

M & L Rendering 5mm thick in CM (1:3) on fair faces of brick work ceilling concrete surfaces to be finished even and fair complete all as specified and directed.

M & L for preparation of new plastered surfaces of ceiling and and applying three coats of white wash complete all as specified and directed .

Taking up or down steel tubing and connections,20mm dia including cleaning for re?fixing or removal to store Complete all as specified and directed.

Taking up or down steel tubing and connections,15mm dia, including cleaning for re?fixing or removal to store Complete all as specified and directed.

Supplying and laying of 15 MM CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S&F GI tubes medium grade with all fitting fixed to wall and ceilling or laid in floor of 20 mm bore of pipe complete all as specified and directed.

S & F in repair bib tap fancy type cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia pipe complete all as specified and as directed. Make -Jaquar Cat No FUS-29037 Fusion, Grohe Model No. 20237001, Cera Model No F1014151

S & F in repairs vitreous china squatting pan orissa pattern long pan size 580 mm x 440 mm white with spun pipe ‘P’ or ‘S’ trap including lead joint and CI spun branch piece , front or back inlet and foot rests excluding flushing cistern & flush pipe but incl. cement concrete bedding fixed complete all as specified and as directed.

S&F in repair low level flushing systern PVC valveless syphonic action type 10 ltr capacity complete all as specified and directed .

S&F in repair Stop valves angle, fancy type , screwed down for iron pipe and fixed to 15mm bore pipe , complete all as specified and directed.

S&F 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and dircted

Dismantling of water tanks capacity exc 500 ltrs and n.exc 1000 ltrs and removing to store complete all as specified and directed.

S & F 1000 litre rotational moulded tripple layer polyethlene water storage tanks white colour (cylindrical vertical with closed top) and suitable size of MS tasla with locking system hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

Dismanting of existing sunken treatment including plaster and M&L for water proofing treatment on existing sunken floor/wall with the following specification complete all as specified and directed- (a) 15mm thick (average) plaster in CM 1:3 on sunken floors and walls using WPC in as per manufacturer instruction (b) Apply one coat bituminous primer @ 0.5 Kg/ Sqm on walls and floor conforming to IS 3384-1965 on prepared surface till the surface is properly impregnated (c) Apply hot bitumen 85/25 grade @ 1.2 Kgs/Sqm confirming to IS 702-1988 (d) Laying polymeric water proofing memberance weight not less than 3.0 Kgs/Sqm as per manufacturer instructions confirming to IS (e) One spout of 40mm GI pipe length 0.45 M shall be provided in sunken floor (f) Filling of sunken floor with PCC 1:5:10 upto height directed (g) fixing of trap as per site requirement Complete all as specified and directed

S & F in repair tubular towel rail 20mm dia 60 cm long between flange, brass chromium plated including bracket fixed in repairs complete all as specified and directed

S&F 15mm Pillar taps, fany type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks fly-nuts, screwed for iron pipe and fixed complete all as specified and directed

S&F vitreous china white wash basins, angle back type of size 400mmx400mm including brackets, cutting for and pinning the ends of brackets or erecting stands including 32mm bore dia waste coupling of PTMT ( Half or full threaded) ,(minimum weight 32 mm-45mm-60gms) with 32 mm High density polyethylene pipes (HDPE) of pressure rating 6kgf/cm² fixed complete to walls in floors complete all as specified and directed

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 square metre each, complete all as specified and dircted

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exc 1.5 sqm not exceeding 4 square metre each, complete all as specified and directed

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately) complete all as specified and directed

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: Stainless steel butt hinges shall be paid separately) Complete all as specified and directed

M & L for Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type wiremesh door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: Stainless steel butt hinges shall be paid separately) Complete all as specified

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm double side prelam PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed

S&F Factory Made Solid PVC Moulded Door Shutter with Particle Board Core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed complete all as specified and directed.

S&F 150 mm, long, Aluminium anodised, barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F 150 mm long , extruded aluminium alloy handles fabricated type anodised and fixed complete all as specified and directed.

S&F Aluminium anodised sliding door bolt 250 mm long plate type stove enamelled black with bright bolt not less than 12 mm dia with and incl a minimum of 6 bolt and nut four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F Steel Window 1.25mm thick Box Type (primer coated) ERW hollow P section of size 60mm x 25mm, 1.25 thick sheet single rebated comprises glazed Skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T- Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T- Section of size 60mm x 25mm and 1.25mm thick including following fitting welded to frame shutter: (a) Hold Fast, 150mm long of 12mm square bar made to shape – 04 Nos per window (b) Handles of Z Sec 100mm long (c) Stopper – 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges – 01 No per leaf (e) MS Pintal hinges of size 75mmx75mmx12mm-02 Nos per leaf Note : Glass shall be measured and paid separately under appropriate item etc complete all as specified and directed.

S&F Steel Window 1.25mm thick Box Type ( primer coated) ERW hollow P section of size 60mm x 25mm single rebated comprises gauged Skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T- Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T- Section of size 60mm x 25mm and 1.25mm thick including following fitting welded to frame shutter: (a) Mild Steel Hold Fast,150mm long of 12mm Square bar made to shape – 04 Nos per window (b) Handles of Z Sec 20mm x 100mm long (c) stopper – 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mmx63mm welded to hinges – 01 No per leaf (e) Mild steel Pintal hinges of size 75mmx75mmx12mm-02 Nos per leaf complete all as specified. Note: Wire mesh shall be measured and paid separately under appropriate item etc complete all as specified and directed.

All as per item above but as in ventilator fixed type (partly glazed and gauzed) complete all as specified and directed.

S&F 4.8mm thick, sheet glass ordinary quality and glazing with oil putty in square n exc 0.50 Sqm in each pane complete all as specified and directed.

S&F Galvanized mild steel wire cloth of 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staples or with wooden beads, screws and nuts botls etc complete all as specified and directed.

Dismantling wrought iron / Mild Steel work of any description not otherwise provided for complete all as specified and directed.

S & F MS joist channel , angle or Tee section MS tubes, flats square bars etc fixed indepently or framed or without connecting plates, (cut to ordinary lengths i.e. within 20mm of the length indicated) trusses etc any type framing including purlins and rafters etc complete all as specified and directed.(Fe 410-W Gde E-250 Quality A) complete all as specified and directed.

S&F in repair Wire netting of galvanised steel wire 1.40mm dia and mesh size 25mm fixed with tinned tacks of wire staples complete all as specified and directed

M&L for preparation of new or previously untreated surface of steel or iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint etc Complete all as specified and directed

M & L for 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in plinth protection finish without using extra cement complete all as specified and directed.

Removing and roughing of surface existing water proofing treatment (incl APP membrane, plaster, PCC, padding, bricks tiles etc) of any type all as directed by Engr in charge and dispositing off out side defence land.

Cleaning the surface by roughening, sweeping clean and washing down and applying cement slurry @ 3 Kgs / Sqm complete all as specified and directed.

M&L for 40 mm thick cement concrete 1:2:4 type B-0 (12.5 mm graded stone aagregate) as in RCC roof surface with mxing of water proofing compound 3% by the weight cement to horizontal or vertical finished cement concrete surface even and smooth using extra cement including necessary form work (water proofing compound will be measured separately.)

M&L for preparation of newly plastered surfaces of roof including cleaning the surface by using wire brush / pressure hose and applying high performance polyurethane liquid membrane roof casting cold in two coat @ 1.5 Kg / Sqm with spray / brush an elogation of 300% to 700% and tensile strength not less than 3 N / Sqm as per ASTM D412 and ASTM D23070, crack bridging ability of 3.5 mm as per ASTM C 1305, shore a hardness of not less than 60 as ASTMD 2240. The item includes epoxy prime applied @ 0.15 Kg / Sqm and a geotexitile of 40 GSM to be applied over first coat while first coast is still wet complete all as manufacturer instruiction and sound engineering practice complete all as specified and directed. Note :- Work shall be executed by authorized applicator of manufacture as per manfaucturer instructions and roof height upto double storey building.

Taking down copper/aluminium point wiring of any description and any position (light, fan, socket or power point) complete, including fixture and fittings such as switches,socket, ceiling rose,lamp holder,pendants, bracket and regulator etc and removing material from site including making good disturbed surface to match with the existing surface complete all as specified.

Taking down copper/aluminium sub main wiring and making good disturbed surfaces to match with the existing surface roof/wall/floor complete all as specified and as directed.

Material and labour for concealed Point wiring for one light point/fan point /bell point controlled by one switch (using red, black and green etc colour wires as colour coding) complete with 1.5 Sqmm (nominal cross section area) single core FRLS PVC insulated unsheathed and multi strand copper conductor cable 1100 volt (ISI marked) drawn through and including PVC conduit 20mm dia (medium duty, ISI marked) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction boxes etc., including Pressed steel powder coated sunken modular terminal box (Min 60mm deep, suitable size) concealed in wall, including 3mm thick bakelite plastic laminated sheet top cover for sunken boxes flush to surface for mounting of switches / socket / regulator etc, including provn of 1.5 Sqmm single core FRLS PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using CM (1:3) complete all as specified and as directed. Note- Switch, socket, Regulatro & White cover plate with frame of different module should be measeured & paid separately.

All as per item 59 here in before but for One 6 Amp socket point with switch on an independent board with 2.5 Sqmm (FRLS) copper conductor cable complete all as specified & directed

All as per item 59 here in before but for One 6 Amp socket point with switch on same board complete all as specified & directed

All as per item 59 here in before but for one 16 Amp socket point with switch on independent board with 4.0 Sqmm (FRLS) unsheathed copper conductor single core multistranded complete all as specified & directed.

S&F Modular switch 1 way 6A,1 Module complete all as specified and directed.

S&F Socket Modular , 6A - 2/3 pin combined 2 Module complete all as specified and directed.

S&F Modular switch 1 way 16A, 1 Module complete all as specified and directed.

S&F Socket Modular 16A - 2/3 pin combined 2 Module complete all as specified and directed.

S&F White cover plate with frame, 1 module complete all as specified and directed.

S&F White cover plate with frame, 2 module complete all as specified and directed.

S&F White cover plate with frame, 3 module complete all as specified and directed.

S&F White cover plate with frame, 4 module complete all as specified and directed.

S&F White cover plate with frame, 6 module complete all as specified and directed.

S&F White cover plate with frame, 8 module complete all as specified and directed.

S&F Modular electronic Fan step regulator, 120W - 2 module complete all as specified and directed

S&F LED decorative wall light fixture made up of polycarbonate, suitable for 09W TU retrofit B-22 including LED bulb 09 watt of colour temp 3000 K & luminaire lumen >1000 lm complete all as specified and directed.

S&F ceiling rose PVC/Poly carbonate isolated body three terminal AC 230 volts complete all as specified and directed.

M&L for sub main wiring with two single core 6 Sqmm FRLS copper conductor PVC insulated and unsheathed cable including PVC conduit medium grade (appropriate size) concealed in wall for sub main connection including 6 Sqmm (FRLS) insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly all as specified. (Note :- Two runs of 6 sqmm (FRLS) and one run of 6 sqmm (FRLS) copper conductor shall be measured as one unit length.)

Supply and fixing in repair of VTPN DB 12 way suitable for Mounting MCCB as Incomer of rating 100 Amp with suitable rated bus bar having IP-43 protection and double metal door concealed in wall including connection with aluminium thimbles as required complete all as specified.

Supply and fixing in repair of MCB distribution board SPN 240 Volt 8 way with 200 Amp rated bus bar having IP-43 protection and double metal door concealed in wall including connection with aluminium thimbles as required complete all as specified.

Supply and fixing in repair of MCB distribution board SPN 240 Volt 4 way with 200 Amp rated bus bar having IP-43 protection and double metal door concealed in wall including connection with aluminium thimbles as required complete all as specified.

S&F of MCCB 100 Amp, 16KA, 4 Pole including complete electrical connection complete all as specified and directed

S&F of MCB SPN 63 Amp 240 volt 'C' curve 10 KA complete all as specified and directed.

S&F of MCB SP 10 to 32 Amp 240 Volt 'C' curve 10 KA complete all as specified and directed.

Supply and fixing LED lights fitting 4 feet, 20W, 220V, AC, Batten type fitting including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose having luminaire lumen >2000 lm complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC Batten type including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed

S & F of post Top lantern outdoor type 20 watt LED light AC 50 Hz 230 V indirect with IP-65 protection resistant to impact and corrosion ftee and better uniformily complete including dismentling all as specified and directed.

S & F building security LED Light 30 Watt sensor based made up pressure die-cast aluminium housing with high power LED as lighting source and lens embedded PC having top opening separate driver compartment with IP-65 protection and impact resistance of IK 07 for building secuity purpose with bracket size made of GI pipe medicum grade 25 mm dia 1.5 mtr long bend to shape as required and fixing with two nos MS Clamp of size 25x6 mm for fixing of builiding security light fittings completed all as specified and directed.

Supply and Laying cable XLPE Insulated screened PVC bedded, galvanized steel strip armoured service cable pole to building electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 Sqmm 4 Core complete incl dismentling all as specified and directed

S & F in of 40 mm bore GI Tubing light grade with all fittings laid across road, in trenches or across PCC drain, along electric pole or floor/wall for cable protection with suitable size of MS Clapms and nut and bolts/washer complete incl dismentling all as specified and directed.

M & L of Sand cushioning for cables complete all as specified and directed .

M & L of old size brick well burnt, laid flat, for cable protection complete all as specified and directed.

Excavation in trenches not exceeding 1.5 mtrs wide and not exceeding 1.5 mtrs in depth for laying of cables including getting out in any type of soil complete all as specified and directed.

Returning filling in including spreading, leveling ,and well ramming, in layers not exceeding 25 cm each layer of any type of soil complete all as specified and directed

Removing surplus excavated material from site not exceeding 50 mtrs from starting point and depositing where directed at level not exceeding 1.5 mtr above the starting point complete all as specified and directed

S&F in repair of MCB distribution board SPN 240 Volt 2 way with 200 Amp rated bus bar having IP-43 protection and double metal door concealed in wall including connection with aluminium thimbles as required complete all as specified.

Taking down and Up of ceiling fan including accessories such as down rod (upto 600mm length), canopy and fan blade and refixing the same with flexible copper wire of size 23/0.0076 Sqmm upto 0.40 mtr with fan connector to ceiling rose complete all as specified and directed.

Material and labour for Earthing complete with galvanised iron earth plate electrode of size 600 x 600 x 6 mm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including GI earthing wire of size 4 mm dia by means of GI bolts/nuts/washers and protected by 15 mm bore GI light grade pipe upto test point or upto main switch board, HT/LT equipments, fixing with 02 Nos nuts and bolts and protection pipe fixed with and including flat iron clamps, bolts, nuts and washers. Earth plate shall be surrounded by alternate packed layer 15 cm thick of charcoal or coke and common salt all around bottom and top. 20 mm bore GI medium grade pipe for watering and including funnel, wire mesh, PCC chamber pit made with PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) including necessary form work, excavation and earth work in any type of soil, returning filling and disposal of surplus soil to a distance not exceeding 50m, Pit cover 40mm thick made with RCC (1:2:4) type B1 (using 20 mm graded stone aggregate) including TMT reinforcement 8mm dia @ 75mm c/c both way, MS handle 12mm dia, cover rest on MS angle iron frame 40x40x6mm embeded in concrete duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified & shown in electrical plate No. 3 of SSR 2009 (Part-I) complete incl dismantling all as specified and as directed by Engineer-in-charge. Note:- (i) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) Protection pipe and GI earthing wire upto test point or upto electric equipment from top of earth plate shall be included in the unit rate of this item. (iii) The earth testing arrangement should be done by the contractor as per direction of Engineer-in-charge.

A K ENGINEERS AND SONS (BID ID -3386832)

M/S WASEEM KHAN CONTRACTOR (BID ID -3394715)

M/S SRI JAGDAMBE TRADERS (BID ID -3395012)

M/S DEVENDRA KUMAR GUPTA (BID ID -3387125)

B.K.ASSOCIATES (BID ID -3381768)

M/s R.V. Constructions (BID ID -3390778)

MD BUILDER (BID ID -3393519)