Construction Balance work of New Type Primary Health Centre at Sherikhawaja Poonch.

Amount

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth within a lead of 50 metres having classification of soil as:-

All Kind of Soil =40%

Ordinary Rock=60%

Providing and laying in position cement concrete of grade M7.5 mix including curing but excluding the cost of centring and shuttering. All work upto plinth level.

Providing and laying in position cement concrete of grade M15 mix including curing but excluding the cost of centring and shuttering. All work upto plinth level

Reinforced cement concrete work of grade M20 mix in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of cement, centering and shuttering, finishing and reinforcement. Columns

Reinforced cement concrete work of grade M20 mix in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring,shuttering,finishing and reinforcement.

Foundations, footings, bases of columns etc. for mass concrete.

Suspended floors, roofs, landings, balconies and access platforms.

Shelves (cast-in-situ)

Lintel, beams, plinth beams, girders, bressumers and cantilevers.

Columns, pillars, piers, abutments, posts and struts.

Stairs (excluding landings) except spiral staircases.

Edges of slabs and breaks in floors and walls under 20cm wide

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay (non-modular) bricks of class designation 75 in foundation and plinth including curing complete in Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level in foundation and plinth including curing in Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Half brick masonry with common burnt clay (non-modular) bricks of class designation 75 in foundation and plinth including curing in cement mortar 1:4(1cement:4coarse sand)

Extra for half Brick masonry in superstructure above plinth level upto floor V level.

Providing and fixing pressed steel door frames conforming to IS: 4351,manufactured from commercial mild steel sheet of 1.60mm thickness, including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.60mm pressed, mild steel welded or rigidly fixed together by mechanical means, including M.S pressed butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface fixing with carbon steel galvanized dash fastener of required dia and size (to be paid for separately).

Providing and fixing 35mm thick panelled or panelled and glazed shutters for doors,windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete (Note: -Butt hinges and necessary screws shall be paid separately) using second class deodar wood.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick using Decorative ply wood both side decorative veneer (type 1) conforming to IS 1328 BWR type

Providing and fixing 35mm thick glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws Using second class deodar wood.

Providing and fixing 35mm thick wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws using second class deodar wood.

6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand)

15mm Cement plaster of mix 1 : 6 ( 1 cement : 6 fine sand) Interior

20mm Cement plaster on the rough side of single or half brick wall of mix 1:6 (1cement: 6 fine Sand)

Providing and applying Plaster of Paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer INTERIOR

Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm) EXTERIOR

Applying priming coat With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Applying priming coat With ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel galvanized iron/steel works

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc complete on steel work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade (Two or more coats on new work) over an under coat of suitable shade with ordinary paint of approved brand and manufacturer.

Providing and laying vitrified floor tiles 600x600mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments

Providing and laying Vitrified tiles in sizes 600x600mm (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shades, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints

Supply and Filling of Stone in Horizontal with hand packing

Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete.

Making plinth protection with common burnt clay bricks of class designation 7.5 laid on edge in cement mortar 1:6 (1 cement : 6 coarse sand) with 12 mm thick bed of cement mortar 1:6 (1 cement : 6 coarse sand) over 75 mm bed of dry brick aggregate 40mm nominal size rammed, consolidated and grouted with fine sand. The top of bricks pointed with cement mortar 1:3 (1cement: 3 fine sand) and curing complete.

Making soak pit 2.5 m diameter 3.0 meter deep with 45x45 cm dry brick honey comb shaft with common burnt clay (non modular) bricks of class designation 7.5 bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

Carriage of Material By MT

Agg above 40mm upto 15Km

Agg below 40mm upto 15Km

Sand upto 15Km

Sand upto 160Km(for Plastering)

Cement & Steel upto 25Km

Bricks upto 170Km

Stone upto 5Km

Providing and fixing G.I. pipes of medium class having dia 40mm with G.I. fittings excluding trenching and refilling etc. (external work)

Providing and fixing G.I. pipes of medium class having 15mm dia. Nominal bore complete with G.I. fittings and clamps,including cutting and making good the walls having dia 15mm etc.:(Internal Work)

Providing and fixing G.I. pipes of medium class having 20mm dia. Nominal bore complete with G.I. fittings and clamps,including cutting and making good the walls having dia 25mm etc.:(Internal Work)

Making connection of G.I. distribution branch with G.I. main of sizes 25 to 40mm nomial bore by providing and fixing Tee, including cutting and threading the pipe etc. complete

Providing and fixing brass bib cock of approved quality having 15mm nominal bore.

Providing and fixing brass bib cock of approved quality having 15mm nominal bore.

Providing and fixing gun metal gate valve of 25mm nominal bore with C.I. wheel of approved quality (screwed end)

Providing and fixing gun metal gate valve of 32mm nominal bore with C.I. wheel of approved quality (screwed end)

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete.(25mm nominal bore)

Providing and filling sand of coarser grade around the G.I. pipes in external works

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work)

15 mm nominal bore

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931

Providing and fixing 15 mm nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 grams

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality.

Providing and fixing 15 mm nominal bore of standard back type C.P. brass close hole basin mixer pillar tap of approved quality and make, weighing not less than 1.970 kg

Providing and fixing PTMT grating of approved quality and colour Circular type 100 mm nominal dia.

Providing and fixing PTMT grating of approved quality and colour Circular type of 125 mm nominal dia with 25mm waste hole

Providing and fixing PTMT soap dish holder breadth 102mm, height of 75mm with concealed fitting arrangements, having length of 138mm, weighing not less than 106gms.

Providing and fixing un plasticized P.V.C. nuts, collars and bush of approved quality and colour connection pipe with PTMT 15 mm nominal bore with 45 cm length.

Providing and fixing Coupling/Socket Stainless Steel Fitting of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. For 15.88 mm outer dia pipe

Providing and fixing Coupling/Socket Stainless Steel Fitting of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. For 28.58mm outer dia pipe

Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. Coupling/Socket For 34mm outer dia pipe

Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. Reducer For 28.58 mmx15.88 mm outer dia pipe.

Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. Reducer For 34.00 mmx28.58 mm outer dia pipe.

Providing and fixing Reducer Stainless Steel Fitting of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. For 42.70 mmx34.00 mm outer dia pipe.

Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M profile and with O-ring sealing gasket of EPDM material of required dia 15.88mm outer dia Elbow 90 degree

Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M profile and with O-ring sealing gasket of EPDM material of required dia 28.58mm outer dia Elbow 90 degree

Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M profile and with O-ring sealing gasket of EPDM material of required dia 34.00mm outer dia Elbow 90 degree

Providing and fixing required Stainless Steel Elbow 90 degree of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M profile and with O-ring sealing gasket of EPDM material of 34.00mm outer dia

Providing and fixing required Stainless Steel Egual Tee of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M profile and with O-ring sealing gasket of EPDM material of dia for 15.88mm outer dia pipe

Providing and fixing required Stainless Steel Egual Tee of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M profile and with O-ring sealing gasket of EPDM material of dia for 28.58mm outer dia pipe

Providing and fixing required Stainless Steel Egual Tee of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M profile and with O-ring sealing gasket of EPDM material of dia for 34.00mm outer dia pipe

Providing and fixing required Stainless Steel Egual Tee of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M profile and with O-ring sealing gasket of EPDM material of dia for 42.70mm outer dia pipe

Providing and fixing required Stainless Steel Reducing Tee of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M profile and with O-ring sealing gasket of EPDM material of for 28.58mm x 15.88mmouter dia pipe

Providing and fixing required Stainless Steel Reducing Tee of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M profile and with O-ring sealing gasket of EPDM material of for 34.00mm x 28.58mmouter dia pipe

Providing and fixing required Stainless Steel Reducing Tee of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M profile and with O-ring sealing gasket of EPDM material of for 42.7mm x 34.00mmouter dia pipe

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:18.2.1 W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40mm C.P. brass waste and 40 mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the walls wherever required of size 600x450x200mm

Providing and fixing P.V.C low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete: 10 litre capacity -white.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings completeof 32 mm dia

Providing and fixing 600x120x5mm glass shelf with edges round off supported on anodized aluminum angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc. complte.

Providing and fixing toilet paper holder of C.P Brass

Providing and fixing PTMT Waste coupling 31mm of 79 mm length and 62 mm breadth weighing not less than 45gms. for wash basin and sink, of approved quality and colour:

PVC Pipe 110mm

PVC Pipe 75mm

PVC TEE 110mm

PVC TEE 75mm

PVC DOOR BEND 110mm

PVC DOOR BEND 100mm

PVC COLLAR 110mm

PVC COLLAR 75mm

PVC TAPE

PVC SOLUTION

Providing and fixing bright finished brass butt hinges with necessary srews complete of size 125 x85 x5.5mm (Heavy Duty)

Providing and fixing bright finished brass Butt hinges with necessary srews complete of size 75 x65 x4mm (heavy Duty)

Providing and fixing bright finished brass tower bolts (barrel type) withnecessary screws etc. complete. : (250x10mm)

Providing and fixing bright finished brass tower bolts (barrel type) withnecessary screws etc. complete. : (100x10mm)

Providing and fixing bright finished brass door latch with necessary screws etc. complete.

Providing and fixing bright finished brass handles with screws etc. complete : (125mm)

Providing and fixing bright finished brass handles with screws etc. complete : (100mm )

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in existing surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. ( Group C)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in existing surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. ( Group B)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit.

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 6 sq. mm + 1 X 4 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Bell push

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.

1 or 2 Module

3 Module

6 Module

8 Module

12 Module

18 Module

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Upto 450 mm sweep

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Single pole and neutral

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required vertical/Hoezontal run.

Supplying and fixing of following rating 240 Volts "C" Series miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning. (Make as per annexure enclosed).

Triple Pole and Neutral 63/40 Amp.

Supplying and fixing of surface 15/18 watt LED type. Ceiling light including connections etc as required.

Supplying and fixing of 10 watt LED batten fitting for Mirror Light including connections etc. as required.

Supplying and fixing of surface mounted 20/22 watt batten LED tube fiiting 4 feet long including connections etc as required.

Supplying & fixing 50W LED Flood light fitting complete with connection,testing etc

Supplying and fixing of following electrical items suitable for operating on 240/230Volts AC, 50 Hz including connections etc. as required.

Ceiling fan 1200 mm sweep (5 star Rating)

Exhaust fan 300 mm size

2-way AC Box

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Providing and Fixing of 8way DD (4+24)Distribution Board

Providing and Fixing of 4way DD (4+12)Distribution Board

Providing and fixing of L.T.Panel after fabrication of panel with 14 CRCA Sheet,hinged lockable door,LED Indicator Lamp,3-phase Bus Bar,powder coated along with following accessories:- incoming-400A 4P 50K MCCB-1NO. Out going-100A 25kMCCB-4NO,200A MCCB 50K-1, 63A 4P 25K MCCB -4 NO,200A 4P-change over switch 1NO.,63ATPN MCB-3N0.Complete with all lift and leads,Testing ,Commissioning etc.MAKE:MCCB/MCB-LEGRAND/ABB/ L&T-(Main L.T.Panel)

Providing and Laying 300 Sqmm 3.5 core Pvc Insulated AL.Cable along with reqd.size of AL.Glands.

SITC of M.S Pipes (C class) including cutting, screwing, welding etc. and providing all fittings e.g flanges, bends, tees, elbows reducers, clamps, hinges etc. Painting with one coat of primer and two coats of synthetic enamel of approved shade of following sizes::(in mtr)

80 mm dia

25 mm dia

SITC of single headed oblique pattern hydrant Landing valve with 80mm dia flanged inlet and 63mm dia Instantaneous type female outlet complete with cap and all Accessories ISI marked.

Supply of non-percolated flexible hose RRL 63mm dia x 15 mtr long complete with instantaneous type 63mm dia male and female ISI marked coupling and Riverted to hose pipe with riverts and copper wire.& ISI marked

Supply & installation of gunmetal 63mm dia short branch pipe with 20mm dia nozzle , ISI marked.

SITC of First aid hose reel wall mounting swinging type complete with drum & brackets, 25 mm dia ball valve & 20 mm dia 30 mtr long high pressure pad hose with shut off nozzle complete as req.

SITC of cast iron double flanged ISI marked Butterfly valve complete with rubber insertion, nuts, bolts, washers etc. of following sizes: 80mm dia

Supply & installation of weather proof hose cabinets fabricated from 18 swg MS sheet/section with full front glass door and suitable to accommodate 2 nos 15 mtr long hoses and 1 no branch pipes as req.

SITC of gunmetal Fire Brigade connection with collecting head 63mm,4 way instantaneous type male couplings with flanged outlet complete with blank caps nuts, bolts & rubber insertions, conforming IS:904-1983

Supplying, Installation, Testing and Commissioning of electric driven pump suitable for automatic operation andconsisting of following: complete in all respect as required. (a) Horizontal type, multistage, centrifugal,split casing pump of cast iron body &bronze impeller with stainless steel shaft,mechanical seal and flow of 450 Ipm at 35 m. head confirming to IS :1520 (b) Suitable HP SQ cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz. AC with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation,conforming to IS-325. (c) M.S.fabricated Common base plate,coupling, coupling guard, foundation boltsetc.as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads. The job also includes Supply, installing, testing and commissioning of Control panel & cable for fire pumps of required specifications as per the motor ratingand site requirements.

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & Suitable for operation with amplifier i/c line matching transformer etc. complete as required.

Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

Supplying of ABC type fire extinguishers filled with MAP-50 powder, 4 kg capacity. Complete with discharge arrangement, high-pressure hose pipe, leak detection tested and ISI approved with standard warranty .

Supplying of CO2 type fire extinguishers 4.5 kg capacity. Complete with discharge arrangement, high-pressure hose pipe, leak detection tested and ISI approved with standard warranty .

supplying of 5 Kg Ceiling Mounted Fire Extinguisher Mono Ammonium Phosphate Powder 90, Stored Pressure Type, Pressure Gauge, Auto discharge mechanism on temperature rise, Applicable on Class A,B,C and electrically started Fire, Leak Detection Tested and ISI approved with standard warranty .

Supplying a set of GI fire bucket with round bottom as per IS standards. Each set comprising of 4 nos buckets each of 9 ltrs capacity including fixing suitable brackets in the hook for holding buckets painted with red paint & filled with sand in 2 buckets of each set

M/S GURNAM SINGH

Manohar Singh Sasan