PROVN OF GRIT WASH TO CERTAIN OTM BLDGS AT 12BRD AND PROVISION AND INSTALLATION OF IRON/ALUMINIUM/GRILLS AT IT SECTION AT 12BRD UNDER GE (AF) TUGHLAKABAD

Amount

Taking down Cement plaster including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed by Engr-in-charge.

M&L for Rendering 15mm thick in cement mortar (1:6) on other than fare face of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement complete all as specified and directed by Engr-in-charge. (350+45)

M&L for Rendering 5mm thick on fair faces of brick work or concrete surface in cement mortar in (1:3) on ceiling without using extra cement complete all as specified and directed by Engr-in-charge.

M&L for applying 2 coats of OBD on new surface of walls over 3mm thick wall care putty complete all as specified and directed by Engr-in-charge. (350+45)

M&L for preparation of new undecorated surfaces and apply three coat of white wash on ceiling complete all as specified and directed by Engr-in-charge.

Dismantling of old brick tiles or terracing tiles, single layer on roofs complete all as specified and directed by Engr-in-charge.

Demolition of existing mud in roofs of any thickness including plastering and leaping, whether full thickness removed or only a part there of, and removing of mud complete all as specified and directed by Engr-in-charge.

Roughening the surfaces of old concrete roof surfaces by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and directed by Engr-in-charge.

Cutting out cracks to V-section in existing roofs or terracing cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand (1:1) (by weight) complete all as specified and directed by Engr-in-charge.

M&L for PCC (1:2):4), type B1 by using 20mm graded stone aggregate in padding/mass concrete and haunching complete all as specified and directed by Engr-in-charge.

M&L for 10mm thick rendering in CM (1:4) using water proofing compound at the rate of 3% weight of cement over concrete surfaces complete all as specified and directed by Engr-in-charge.

Supply only water proofing compound complete all as specified and directed by Engr-in-charge.

M&L for APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3 mm thick reinforced with polyester non wove fabric (wt not less than 150 gms /Sqm ) land on Providing & laying a coat of cold applied bitumen 85/25 based primer on entire surface @ 0.300 Ltr/Sqm on dry and clean surfaces complete all as specified and directed by Engr-in-charge.

M&L for washed stone grit plaster on exterior walls in two layers under layer 12 mm cement plaster (1:4) (1 cement : 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square meter , top layer 15 mm cement plaster (1: 1/2::2) (1 cement 1/2 coarse sand : 2 stone chipping 10 mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing the top layer with brushes and water to expose the stone chippings complete all as specified and directed by Engr-in-charge. Note: Payment for providing grooves shall be made separately.

Forming groove of uniform size 15 mm wide and 15 mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens , nailed to under layer including removal of wooden battens repair to the edges of panels and finishing the groove complete all as specified and directed by Engr-in-charge.

Dismantling existing water tanks Exc 250 & N exc 500 and S&F New Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed by Engr-in-charge.

Dismantling existing water tanks Exc 500 & N exc 1000 and S&F New Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed by Engr-in-charge.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed by Engr-in-charge.

M&L for bricks works with sub class "B" bricks straight or curved on plan exc 6m mean radius built in CM (1:4) complete all as specified and directed by Engr-in-charge.

M&L for bricks works with sub class "B" bricks straight or curved on plan exc 6m mean radius built in CM (1:6) and external face of brick pointed flush in the same mortar complete all as specified and directed by Engr-in-charge.

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed by Engr-in-charge.

M&L for renewing Glazed tiles in patches, area n exc 5 Sq.m. Including removing and cleaning old tiles, preparing beds and laying or setting, jointing and pointing new or old tiles complete all as specified and directed by Engr-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in-charge.

M&L for 25mm thick cement concrete flooring (1:2:4) type B1 using 20 mm graded aggregate finished even and fair complete all as specified and directed by Engr-in-charge.

M&L for Screed bed or bedding layer of mortar 15 mm thick in CM (1:6) for laying floor finishes complete all as specified and directed by Engr-in-charge.

M&L for Non- skid joint free ceramic coloured printed tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engr-in-charge.

M&L for rendering 10 mm thick in CM (1:3) finished even and fair as on brick or concrete surfaces for laying wall tiles complete all as specified and directed by Engr-in-charge.

M&L for colour joint free Glazed ceramic tiles in vertical surface 350x250x7mm/450x350x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed by Engr-in-charge.

M&L for Dark Shade Vitrified ceramic tiles 10 mm thick (Square/rectangular) polished area of each tiles not exc 0.36 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement complete all as specified and directed by Engr-in-charge.

Demolition of cement concrete reinforced in any position including cut of bars as required complete all as specified and directed by Engr-in-charge.

M&L for reinforced cement concrete (1:2:4) type B1 using 20mm graded crushed stone aggregate as in chajjas complete all as specified and as directed by Engr-in-Charge.

M&L for Reinforced cement concrete (1:2:4) type B1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engr-in-charge.

M&L for Form work to soffits of suspended slab such as roof slab, floor slab etc n exc 200 mm thick rough finished surface of concrete slab complete all as specified and directed by Engr-in-charge.

M&L for for rough finished surfaces if concrete formwork to sides and soffits if floor or roof beams haunching girder bressummer chajja shelves including supports complete all as specified and directed by Engr-in-charge.

M&L for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-charge.

M&L for Mild steel TMT bars 5 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-charge.

Demolition of cement concrete (un reinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engr-in-charge.

M&L 100mm thick cement concrete (1:2:4) type B2 using 40mm graded aggregate as in path/ plint protection finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed by Engr-in-charge.

M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Engr-in-charge.

M&L for 100 mm thick PCC (1:4:8) type B2 using 40 mm graded crushed stone aggregate as in PCC hard standing, finish the surfaces even and smooth without using extra cement complete all as specified and directed by Engr-in-charge.

Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engr-in-charge.

M&L for Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm m thickness, M-35 grade With grey cement and no pigment complete all as specified and directed by Engr-in-charge.

M&L for cement concrete chequered tiles 20cmx20cmx25mm thick set & jointed with cement mortar (1:3) & pointed in neat cement slurry with grey cement and pigments including 20 mm thick screed bed in cm (1:6) complete all as specified and directed by Engr-in-charge. Make: Coral/Terra ferrma/Ultra

Dismantling Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings complete all as specified and directed by Engr-in-charge.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-charge.

S&F 0.56 mm Plain, Aluminium sheeting, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed) complete all as specified and directed by Engr-in-charge.

Dismantling of wrought iron or Mild Steel work of any description complete all as specified and directed by EIC complete all as specified and directed by Engr-in-charge.

S&F roof trusses Fe 410-W (Gde E-250) quality -A (framed), trussed, purlins, wind tie, crane gantries and rail and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed by Engr-in-charge.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed by Engr-in-charge.

M&L for providing and injecting chemical emulsion for post construction anti-termite treatment along external wall where the acron is not provided using chemical emulsion @7.5 Ltr per sqm of the vertical surface of the sub-structure to a contact of 300mm including excavating channel roding etc colete all as specified and directed by Engr-in-charge.

M&L for filling voids in masonry using chemical emulsion @ one ltr per hole at a distance of 300mm center to centre (Apart) including drilling holes at 45 degree and replugging the existing floor etc compllete all as specified and directed by Engr-in-charge.

M&L for treament to soil under existing floor using chemical emulsion @ one ltr per hole at a distance of 300mm center to center (apart) including drilling and plugging 12mm dia holes with cm (1:2) to match the existing floor etc compllete all as specified and directed by Engr-in-charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) not exceeding 1.5 Sqm complete all as specified and directed by Engr-in-charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exceeding 1.5 sqm and but n,exc 4 sqm each for archives soffits, linings window boarss etc complete all as specified and directed by Engr-in-charge.

S&F for anodised aluminium frame (minimum 50 micron powder coating) for doors windows ventilators with one or more rebates including cleat for fixing etc complete all as specified and directed by Engr in charge

S&F Aluminium powder coated of any colour (thickness or powder coating not less than 50 micron) doors shutters aluminium section weighing 0.55 Kg/Sqm including necessary jointing cleats glazing clips rubber neoprene packing hangles two nos in each door hinges anodised aluminium snap beading screws complete all as specified and directed by Engr-in-charge.

S&F aluminium powder coated of any colour (thickness or powder coating not less than 50 micron) windows and ventilator shutters with aluminium grill side hung type without sash bars aluminium section weighing 0.55KG/Sqm including necessary jointing cleats glazing clips rubber packing anodised snap beading screws anodised aluminium fitting such as peg stay 150 mm long (01 No) hinges type B2 100 mm long (02 No) suitable handle (01 No) complete all as specified and directed by Engr-in-charge.

S&F 12mm thick pre-laminated particle board interior grade pre-laminated both side with decorative choice lamination fixed with screws to timber frame work or as in cubical, partition or cupboards, complete all as specified and directed by Engr-in-charge.

S&F double action floor spring hydraulically regulated made up of aluminium 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed by Engr-in-charge.

S&F 4 lever brass mortice lock, vertical type, size 100 mm complete all as specified and directed by Engr-in-charge.

Taking down ceiling board with frame of any description complete all as specified and directed by Engr-in-charge.

M&L for false ceiling of approved (ISI marked) make with 4mm thick HPS board fixed to galvanised iron steel angled grid 600x600mm size suspended system fixed to MS framed work of approved make and section as specified in SSR Part I with suitable hook/fasteners and GI/almn suspenders not less than 3mm dia @ 1.00m C/C minimum. ceiling system is to be fixed in water level without any sag complete all as specified and directed by Engr-in-charge.

MOHIT ENTERPRISES

NAVYUG VYAPARI

DP Traders

M/S Parshant Associates

M/s R P Enterprises

M/S RK Builders

M/s Gravitas Enterprises