Execution of balanced work in GOs Mess for Bn. Hqr. At BSF Campus Gaya, Bihar.

BILL OF QUANTITY

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

CARRIAGE OF MATERIALS

1 1.1. By mechnical transport including loading, unloading & stacking

a 1.1.1 Lime,moorum,Building rubbish

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in

2 2.8 foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing

of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and

disposal of surplus excavated soil as directed, within a lead of 50 m.

a 2.8.1 All kinds of soil. cum 100 130.8 13080.00

Earth work in excavation by mechanical means (Hydraulic excavator/manual means in foundation

3 2.9 treanches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides

and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of

surplus excavated soil as directed within a lead of 50 mtr.

a 2.9.1 Ordinary rock cum 10.00 212.00 2120.00

4 2.26 extra for every additional lift of 15m or part thereof in.

a 2.26.1 All kinds of soil. Cum 20.00 34.60 692.00

b 2.26.2 Ordinary or hard rock cum 10.00 62.00 620.00

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in

5 2.25 layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, cum 250 83.80 20950.00

lead up to 50 m and lift upto 1.5 m.

Supplying & stackng of good earth at site including royalty and carriage up to 1 km (earht

measured in stacks will be reduced by 20% for Payment).

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15

cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m.

a 2.28.1 All kinds of soil. 100 sqm 10 935.25 9352.50

9 2.34 Supplying chemical emulsion in sealed containers including delivery as specified.

a 2.34.1 Chlorpyriphos/Lindane Emulsifiable concentrate of 20%. Ltr. 100.00 185.95 18595.00

Diluting and injecting chemical chemical emulsion for POST CONSTRUCTIONAL anti-termite

treatment (excluding the cost of chemical emulsion)

Treatment of soil under existing floors using chemical emulsion @ one ltr. Per hol, 300mm apart

a 2.35.3 including drilling 12mm diameter holes and plugging with cement mortar 1:2 (1 cement: 2 coarse

sand) to match the existing floor.

i 2.35.3.1 With Chlorpyriphos /Lindane E C. 20% with 1% concentration. Sqm 250.00 88.25 22062.50

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Providing and laying in position cement concrete of specified grade excluding the cost of centering

and shuttering - All work up to plinth level

a 4.1.3 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cum 2.02363 4514.05 9134.77

b 4.1.6 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) cum 10.00 3888.20 38882.00

c 4.1.8 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) cum 88 3593.30 316210.40

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2

coarse sand : 4 graded stone aggregate 20mm nominal size).

Extra for providing and mixing water proofing material in cement concrete work in doses by Per 50

13 4.12 weight of cement as per manufacturer’s specification kg 1320 35.35 46662.00

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg

14 4.13 per square metre on damp proof course after cleaning the surface with brushes and finally with a Sqm 80 96.65 7732.00

piece of cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded

15 4.17 stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal Sqm 90 338.75 30487.50

size, well rammed and consolidated and grouted with fine sand including finishing the top smooth

17 5.9 Centring and shuttering including strutting, propping etc. and removal of form for:

a 5.9.1 Foundations, footings, bases of columns etc. for mass concrete. sqm 351.95 166.9 58740.46

b 5.9.2 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. sqm 100.00 285.15 28515.00

c 5.9.3 Suspended floors, roofs, landings, balconies and access platform. sqm 820.00 311.2 255184.00

d 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers. Sqm 544.25 262.25 142729.56

e 5.9.6 Columns, Pillars, Piers, Abutments, posts and Struts Sqm 81.39 365.6 29756.18

g 5.9.13 Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards. Sqm 87.00 470.1 40898.70

h 5.9.16 Edges of slabs and breaks in floors and walls.

Small surfaces such as cantilever ends, brackets and ends of steps, caps and bases to pilasters and

columns and the like

19 5.9.19 Weather shade, chajjas, corbels etc. including edges. sqm 80.00 411.1 32888.00

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and

binding all complete upto plinth level

a 5.22.6 Thermo-Mechanically Treated bars kg 29900.00 62.25 1861275.00

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position

and binding all complete above plinth level.

a 5.22A.6 Thermo-Mechanically Treated bars kg 25200.00 62.25 1568700.00

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Providing and laying in position machine batched and machine mixed design mix M-25 grade

cement concrete for reinforced cement concrete work, using cement content as per approved

design mix, including pumping of concrete to site of laying but excluding the cost of centering,

shuttering, finishing and reinforcement, including admixtures in recommended proportions as per

IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength

and durability as per direction of Engineer-in-charge.

(Note :- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per

design mix is payable/recoverable separately).

a 5.33.1 All works upto plinth level. cum 134.75 5242.15 706379.71

b 5.33.2 All works above plinth level upto floor V level. cum 275.00 5781.5 1589912.50

Brick work with common burnt clay F.P.S ( non modular ) bricks of class designation 7.5 in

foundation & plinth in:

a 6.1.2 Cement mortar 1:6 (1 cement: 6 coarse sand) cum 90.00 3316.55 298489.50

Extra for providing and placing in position 2 Nos. 6 mm dia MS bars at every third course of half

brick masonry (with FPS bricks)

Brick work with mechanized autoclaved flyash sand lime non modular bricks conforming to IS :

12894 of class desiganation 10 in superstructure above plinth level up to floor V level :

a 6.42.2 Cement mortar 1:6 (1 cement: 6 coarse sand) cum 4679.45

half brick masonary with non modular mechanized autoclaved flyash sand lime bricks of class

desiganation 10 , conforming to IS : 12894 in superstructure above plinth level up to floor V level

a 6.46.2 Cement mortar 1:4 (1 cement: 4 coarse sand) sqm 568.75

Brick edgeing 7cm wide 11.4cm deep to plinth protection with brick of class desiganition 75

including grouting with cement mortar 1:4 ( 1 cement: 4 fine sand )

Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished)

machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of

required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4

(1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment,

epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss

finish etc. complete at all levels.

a 8.2.1 White marble - Raj Nagar plain /udaipur green marble /zebra black marble

i 8.2.1.2 Area of slab over 0.50 Sqm Sqm 7.00 1980.8 13865.60

b 8.2.2 Granite of any colour and shade

i 8.2.2.2 Area of slab over 0.50 Sqm Sqm 15.00 3083.4 46251.00

Providing edge moulding to 18mm thick marble stone counters, Vanities etc. including machine

29 8.3 polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Extra for providing opening of required size & shape for wash basins / kitchen sink in kitchen

30 8.5 platfrom, vanity counters and similar location in marble / Granite / stone work including Each 15.00 281.1 4216.50

necessary holes for pillar taps etc. Including rubbing and polishing necessary etc. complete.

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative

type, core of block board construction with frame of 1st class hard wood and well matched

commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of

a 9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. sqm 70.00 1578.3 110481.00

25mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges

with necessary screws.

i 9.22 Extra for providing and fixing flush doors with decorative veneering:

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges

of flush door shutters (over all area of door shutter to be measured).

Providing and fixing wire gauze shutters using galvanised MS wire gauze of average width of

b 9.29 aperture 1.4mm with wire of dia, 0.63mm for doors, windows and clerestory windows including

ISI marked stainless steel butt hinges with necessary screws.

34 30 mm thick shutters

a 9.29.1 Second class teak wood Sqm 50.00 2412.7 120635.00

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats,

square or round bars etc. including priming coat with approved steel primer all complete

a 9.48.1 Fixed to steel windows by welding. Kg 100.00 90.75 9075.00

36 9.48.2 Fixed to opening /wooden frames Kg. 2306.00 98.2 226449.20

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc.

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less

c 9.96 than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with nuts and

screws etc. complete:

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than

37 9.97 grade AC 10 as per IS : 1868 ) transparent or dyed toreqired colour or shade with necessary screws

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade

39 9.1 AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc.

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating

41 9.101 not less than grade AC 10 as per IS :1868) transparent or dyed to required colour or shade with

necessary screws etc. complete:

42 9.101.2 Twin rubber stopper Each 31.00 71.55 2218.05

Providing & fixing bright finished brass 100mm mortice latch and lock with 6 levers and a pair of

lever handles with necessary screws etc. complete (Best make of approved quality).

Providing & fixing special quality bright finished brass Cupboard or ward robe locks with four

levers including necessary screws etc. complete (best make of approved quality).

Providing & fixing IS:3564 marked aluminium Die cast body tubular type universal hydraulic door

closer with necessary accessories and screws etc. complete

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work,

44A 10.2 including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer Kg. 10.00 66.5 665.00

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm

44B 10.5 M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a

priming coat of approved steel primer.

a 10.5.2 Using flats 30x6mm for diagonal braces and central cross piece. sqm 5.00 2427.15 12135.75

Providing & fixing factory made ISI marked steel glazed doors, windows and ventilators

side/top/central hung with beading and all members such as F7D , F4B, K11B and K12B etc.

complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars

tenoned and riveted , including providing and fixing of hinges, pivots,including priming coats of

approved steel primer , but excluding the cost of other fitting , complete as per approved design (

( Sectional weight of only steel members shall be measured for payment ).

Fixing with 15x3 mm lugs 10 cm. long embedded in cement concrete block 15x10x10 cm of C.C.

1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Providing and fixing pressed steel door frames conforming to IS:4351 manufactured from

commercial mild steel sheet of 1.60 mm thickness including hinges, jamb, lock jamb, bead and if

required angle threshold of mild steel angle of section 50x 25 mm, or base ties of 1.60 mm pressed

46 10.14 mild steel welded or rigidly fixed together by mechanical means, including M.S pressed but hinges

2.5 mm thick with mortar guards , lock strike plate and shock absorbers as specified and applying

a coat of approved steel primer after pre-treatment of the surface as directed by the Engineer-in-

a 10.14.2 Profile C

i 10.14.2.1 Fixing with adjustable lugs with split end tail to each jamb Mtr 40.00 370 14800.00

47 10.14.3 Profile E

a 10.14.3.1 Fixing with adjustable lugs with split end tail to each jamb Mtr 40.00 404.85 16194.00

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections,

48 10.13 joints mitred and welded, including fixing of necessary butt hinges and screws and applying a

priming coat of approved steel primer.

Fixing with 15x3 mm lugs 10 cm. long embedded in cement concrete block 15x10x10 cm of C.C.

1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc.

49 10.16 including cutting, hoisting, fixing in position and applying a priming coat of approved steel

primer, including welding and bolted with special shaped washers etc. complete.

a 10.16.2 Hot finished seamless type tubes Kg 100.00 97.3 9730.00

Providing and fixing circular/hexagonal cast iron or MS sheet box for ceiling fan clamp of internal

dia 140mm, 73mm height, top lid of 1.5mm thick M.S. sheet with its top surface hacked for proper

50 10.18 bonding, top lid shall be screwed into the cast iron/ MS box by means of 3.3mm dia round headed Each 35.00 117.45 4110.75

screws, one lock at the corners. Clamps shall be made of 12mm dia M.S. bar bent to shape as per

standard drawing.

Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position

and applying a priming coat of approved steel primer using structural steel etc. as required.

51 10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. kg 160.00 77.9 12464.00

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony

52 10.26 railing, staircase railing and similar works, including applying a priming coat of approved steel

Providing and fixing glass panes with putty and glazing clips in steel doors,windows,clerestory

windows,all complete with:

a 10.30.1 4mm Thick glass panes sqm 5.00 657.75 3288.75

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Providing and fixing stainless steel ( grade 304 )railing made of Hollow tubes , channels , plates

etc , including welding grinding , buffing ,polishing and making curvature ( wherever required )

and fitting the same with necessary stainless steel nuts and bolts complete ,I/c fixing the railing

54 10.28 with necessary accessories &stainless steel dash fasteners ,stainless steels bolts etc ,of required size Kg 200.00 558 111600.00

,on the top of the floor or the side of waist slab with suitable arrangment as per approval of

Engineers -in-charge, ( for payment purpose only weight of stainless steel members shall be

considered excluding fixing accesories such as nuts ,bolts, fasteners etc

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a

55 11.3 floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc.

a 11.3.1 40mm thick with 20mm nominal size stone aggregate Sqm 75.00 280.05 21003.75

Cement plaster skirting (up to 30 cm height) with cement mortar 1:3 (1 cement : 3 coarse sand)

finished with a floating coat of neat cement

57 11.13 Providing and fixing glass strips in joints of terrazo/ cement concrete floors

a 11.13.1 40 mm wide and 4 mm thick Mtr. 50.00 29.4 1470.00

Marble stone flooring with 18mm thick marble stone as per sample of marble approved by

58 11.23 Engineer-in-charge over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse

sand) laid and jointed with grey cement slurry including rubbing and polishing complete with :

a 11.23.5 Udaipur green marble Sqm 100.00 1418.95 141895.00

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement

59 11.26 slurry mixed with pigment to match the shade of the slab including rubbing and polishing

complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average)

60 11.27 thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with sqm 50.00 954.1 47705.00

pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be

specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle

green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados

over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey

cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of

matching shade complete

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Providing & laying rectified glazed ceramics floor tiles 300x300mm or more (thickness to be

specified by the manufacturer) of Ist quality conforming to IS:15622 of approved make in colours

White, Ivory, Grey, Fume, Red Brown, laid on 20 mm thick cement mortar 1:4 (1 cement :4 coarse

sand) including grouting the joints with white cement and matching pigments etc. complete.

Providing & laying vitrified floor tiles in different sizes (thickness to be specified by the

manufacturer) with water absorptions less than 0.08% and conforming to IS:15622 of approved

make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand)

including grouting the joints with white cement and matching pigments etc. complete.

Providing and laying brick tiles over mumty roofs, grouted with cement mortar 1:3 (1 cement : 3

64 12.19 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm

layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat :

a 12.19.1 With common burnt clay F.P.S. (non modular) brick tiles of class designation 10 sqm 100.00 283.65 28365.00

Providing and laying pressed clay tiles (as per approved pattern 20 mm nominal thickness of

approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2%

integral water proofing compound laid over a bed of 20 mm thick cement mortar 1:4 (1 cement : 4

coarse sand) and finished neat complete.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate

66 12.21 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per

standard design :

a 12.21.1 In 75x75mm deep chase metre 150.00 109.45 16417.50

Making khurras 45x45 cm with average minimum thickness of 5 cmcement concrete 1:2:4 (1

cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet

1mx1mx400micron, finished with 12mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of

neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing MS holder bat clamps of approved design to C.I. or S.C.I. rain water pipes

embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix (1 cement:2 coarse

sand : 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good

69 12.39 Providing lead caulked joints to sand cast iron rain water pipes and fittings:

Providing and fixing on wall face unplasticised-Rigid PVC rain water pipes conforming to IS:13592

70 12.41 Type A including jointing with seal ring conforming to IS:5382 leaving to 10mm gap for thermal

expansion. (i) Single socketed pipes:

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Providing and fixing on wall face unplasticised- PVC moulded fittings/accessories for

71 12.42 unplasticised-Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with

seal ring conforming to IS:5382 leaving to 10mm gap for thermal expansion.

a 12.42.1 Coupler

c 12.42.6 Shoe (plain)

Providing and fixing unplasticised- PVC pipe clips of approved design to unplasticised-PVC rain

water pipes by means of 50x50x50mm hard wood plugs, screwed with MS screws of required

length including cutting brick work and fixing in cement mortar 1:4 (1 cement:4 coarse sand) and

making good the walls etc. complete.

Providing & fixing to the inlet mouth of rain water pipe cast iron grating 15cm diameter and

weighing not less than 440 gms.

Providing and fixing at all height false ceiling including providing and fixing of frame work made

of special sections power pressed from MS sheet and galvanised in accordance with zinc coating of

grade 350 as per IS:277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with

flanges of 22 mm and 37 mm at 1200 mm centre to centre one flange fixed to the ceiling with dash

fastner 12.5 mm dia x 40 mm long with 6 mm dia bolts to the angle hangers of 25x25x0.55 mm of

74 12.45 required length and other end of angle hanger being fixed with nut and bolts to GI channels 45 mm

x 15 mm x 0.9 mm running at the rate of 1200 mm centre to centre to which the ceiling section 0.5

mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at

450mm centre to centre shall be fixed in a direction perpendicular to GI channel with connecting

clips made out of 2.64mm dia x 230mm long GI wire at every junction including fixing the

gypsum board with ceiling section and perimeter channels

0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long the perimeter of ceiling fixed

to wall/partition with the help of rawl plugs at 450 mm centre to centre with 25 mm long drive all

screws @ 230 mm interval including jointing and fixing to a flush finish of tapered and square

edges of the gypsum board with recommended filler, paper tapes, manufacturers specification and

also including the coat of making openings for light fittings, grills diffusers, cutouts made with

frame of perimeter channels suitably fix all complete as per drawing and specification and

direction of the Engineer-in-Charge but excluding the cost of painting with:

a 12.45.1 12.5 mm thick tapered edge gypsum baord conforming to IS:2095- Part-I. Sqm 100.00 691.4 69140.00

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium

silicate false ceiling tiles of approved texture spintone/ cosmos/ Hexa or equivalent of size 595 x

595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised

section (galvanising @ 120 grams per sqm including both side) consisting of main 'T' runner

suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick

(minimum) sheet, spaced 1200 mm centre to centre, and cross "T" of size 24x28 mm made out of

0.33 mm (minimum) sheet, 1200 mm long spaced between main 'T' at 600 mm centre to centre to

form a grid of 1200x600 mm and secondary cross 'T' of length 600mm and size 24x28 mm made of

0.33 mm thick (minimum) sheet to be inter locked at middle of the 1200x600 mm panel to from a

grid 600x600 mm, resting on periphery walls / partitions on a Peerimeter wall angle pre-coated

steel of size (24x24x3000 mm) made of 0.40 mm thick (minimum) sheet with the help of rawl plugs

at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm

interval and laying 15 mm thick densified edges calcium silicate ceiling tiles of approved texture

(Spintone/ Cosmos/ Hexa) in the grid, including cutting/ making opening for services like

diffuser, grills, light fittings, fixtures, smoke detector etc. wherever required. Main 'T' runners to be

suspended from ceiling using G.I slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm

dia and 50 mm long dash fasteners, 4 mm G.I adjustable rods with galvanised steel level clips of

size 85x30x0.8 mm, spaced at 1200 mm centre to centre along main 'T' bottom exposed with 24 mm

of all T-section shall be pre-painted with polyster baked paint, for all heights, as per specifications,

drawings and as directed by engineer-in-charge.

Note:- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction

shall be made for exposed frames/ opening (cut outs) having area

less then 0.30 sqm. The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light

a reflection > 85%, non - combustible as per B.S 476 part IV, 100% Humidity resistance and also

having thermal conductivity < 0.043 w/m 0KC.

75 13.4 12mm cement plaster of mix :

76 13.7 12mm cement plaster finished with a floating coat of neat cement of mix :

18 mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 (1 cement : 5 coarse

77 13.12 sand) and a top layer 6mm thick cement plaster 1:3 (1 cement: 3 coarse sand) finished rough with Sqm 198.25

78 13.16 6 mm cement plaster to ceiling of mix :

79 13.5 15mm cement plaster on rough side of single or half brick wall of mix:

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Extra for plastering exterior walls of height more than 10m from ground level for every additional

height of 3m or part thereof.

Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare

the surface even and smooth complete.

a 13.37 White washing with lime to give an even shade

82 13.37.1 New work (three or more coats) Sqm. 100.00 11.75 1175.00

Distempering with oil bound washable distemper of approved brand and manufacture to give an

83 13.41.1 New work (two or more coats) over and including priming coat with cement primer Sqm 1000.00 66.7 66700.00

a 13.45 Finishing walls with textured exterior paint of required shade

New work (two or more coats applied @ 3.28 Ltr/ 10 Sqm) over and including base coat of water

proofing cement paint applied @ 2.20 Kg./ 10 Sqm.

Finishing walls with Premium Acrylic Smooth exterior paint with "Silicone additives of required

New work (two or more coats applied @1.43 ltr/10 sqm over and including base coat of water

proofing cement paint applied @2.20kg/10sqm)

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even

a 13.60.1 Two or more coats on new work Sqm 2000.00 60.25 120500.00

87 13.5 Applying priming coat:

With ready mixed pink or grey primer of approved brand and manufacturer on wood work ( hard

Providing and applying two coats of Fire retardent paint unthunned on cleaned wood/ply surface

88 13.58 @ 3.5 sqm per litre per coat including preparation of base surface asper recommendation of Sqm 50.00 267.15 13357.50

manufacture to make the surface fire retardent.

89 13.61 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

13.61.1 Two or more coats on new work Sqm 500.00 53.85 26925.00

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per

manufacturers specifications

Two or more coats applied on walls @ 1.25 ltr/10 sqm. over and including one coat of Special

primer applied @ 0.75 ltr / 10 sqm.

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied

i 13.48.2 @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/ 10 sqm of approved brand or sqm 140.00 67.7 9478.00

Forming groove of uniform size from 12x12mm and 25x15mm in plastered surface as per approved

pattern using wooden battens, nailed to the under layer including removal of wooden battens,

repair to the edges of panel and finishing the groove complete as per specifications and direction of

the Engineer-In-Charge.

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Boring, providing and installing board cast-in-situ reinf. Cement concrete pile of specified diam

and length below pile cap in M-25 in cement concrete, to carry a safe working load not less than

specified, excluding the cost of steel reinf. but including the cost of boring with bentonite solution

and temporary casing of appropriate length for setting out and the pile cap etc. all complete,

including removal of excavated earth with all lifts and leads (Length of pile for payment shall be

measured upto the bottom of pile cap).

a) 20.2.3 450 mm dia piles Mtr. 2154.4

Vertical load testing of piles in accordance with IS:2911 (Part-IV) including installatioin of loading

82 20.6 platform and preparation of pile head or construction of test cap and dismantling of test cap after

test etc. complete as per specification and the direction of Engineer-In-Charge.

a) 20.6.1 Single pile upto 50 tonne capacity

i) 20.6.1.1 Initial test Per Test 38561.8

ii) 20.6.1.2 Routine test Per Test 17422.5

b) 20.6.3 Group of two or more piles upto 50 tonne capacity

i) 20.6.3.1 Initial test Per Test 56332.8

ii) 20.6.3.2 Routine test Per Test 34264.2

ALUMINIUM WORK:

Providing & fixing aluminium work for doors, windows, ventilators & partitions with extruded

built up standard tubular sections/ appropriate Z-sections and other sections of approved make

comforming to IS: 733 & IS:1285, fixed with rawl plugs and screws or with fixing clips, or with

expansion hold fastners including necessary filling up of gaps at junctions, at top bottom and sides

with required of PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight,

mitred & jointed mechanically wherever required including cleat angle, aluminium snap beading

for glazing/panelling C.P. brass/ Stainless Steel screws, all complete as per architectural drawings

& the directions of Engineer-In-Charge. (Glazing and panelling to be paid for separately).

a 21.1.1 For fixed portion

Anodized aluminium (anodized transparent or dyed to required shade according to IS:1868,

Minimum anodic coating of grade AC 15).

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and

93 21.1.2 making provision for fixing of fittings wherever required including the cost of PVC/ neoprene

gasket required. (Fittings shall be paid for separately)

Anodized aluminium (anodized transparent or dyed to required shade according to IS:1868,

Minimum anodic coating of grade AC 15).

Providing & fixing double action hydraulic floor spring of approved brand and manufacture

IS:6315 marked, for doors including cost of cutting floors as required, embedding in floors and

cover plates with brass pivot and single piece MS sheet outer box with slide plate etc. complete as

per the direction of Engineer-In-charge.

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

a 21.4.1 With stainless steel cover plate Each 1.00 1953.1 1953.10

Providing & fixing 100mm brass locks (best make of approved quality) for aluminium doors

including necessary cutting and making good etc. complete.

Providing & fixing aluminium casement window fastener of required length for aluminium

windows with necessary screws etc. complete.

b 21.15.1 Anodized( AC15) aluminium. Each 1.00 50.5 50.50

Providing & fixing aluminium round shape handle of outer dia 100mm with SS screws etc.

complete as per direction of Engineer-incharge.

96 21.16.1 Anodized( AC15) aluminium. Each 1.00 60.95 60.95

Providing and fixing glazing in aluminium doors, windows, ventilator shutters & partitions etc.

97 21.3 with PVC/ neoprene gasket etc. complete as per architectural drawings and the directions of

Engineer-In -Chage (Cost of aluminium snap beading shall be paid in basic item).

a 21.3.2 With float glass panes of 5.5 mm thickness Sqm 1.00 905.75 905.75

b 21.3.3 With float glass panes of 8mm thickness Sqm 1.00 1227.8 1227.80

WATER PROOFING:

Providing and laying integral cement based water proofing treatment including preparation of

surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:

a) Applying a slurry coat of neat cement using 2.75 kg/sqm. of cement admixed with water

proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab

including adjoining walls upto 300mm height including cleaning the surface before treatment. b)

Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115mm size with 50% of

cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming

to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix

1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and

approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto

300 mm height including rounding of junctions of walls and slabs c) After two days of proper

curing applying a second coat of cement slurry

using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645

and approved by Engineer-in-charge. d) Finishing the surface with 20 mm thick jointless cement

mortar of mix1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to

IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved

quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry

and making pattern of 300x300 mm square 3mm deep. e) The whole terrace so finished shall be

flooded with water for a minimum period of two weeks for curing and for final test. All above

operations to be done in order and as directed and specified by the Engineer-in-Charge :

a 22.7.1 With average thickness of 120mm and minimum thickness at khurra as 65 mm. sqm 800.00 786.7 629360.00

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Substitute item

Brick work with common burnt clay F.P.S ( non modular ) bricks of class designation 7.5 in

superstructure above plinth level upto floor V in all shapes and sizes in :

6.4.2 Cement mortar 1 : 6 (1 cement : 6 coarse sand ) cum 168.55 3876.15 653332.83

Half brick masonary with common burnt clay F.P.S (non modular ) bricks of class designation 7.5

plinth level upto floor V level:

6.12.2 Cement mortar 1 : 4 (1 cement : 4 coarse sand ) SQM 250.00 476.85 119212.50

NON SCHEDULE ITEM

Supplying and filling in plinth with local sand under floors including watering, ramming

consolidating and dressing complete.

TOTAL CIVIL WORK A 12379958.63

PLUMBING & PHE SYSTEM

Providing and fixing white vitreous china pedestal type water closet (European type W.C pan)

with seat & lid, 10 ltr low level white PVC flushing cistern manually controlled device (handle

liver), coforming to IS:7231, with all fittings and fixtures complete including cutting & making

good the walls and floors wherever required.

17.2.1 WC Pan with ISI marked white plastic seat and lid. Each 12.00 2885.1 34621.20

Providing and fixing white vitreous chine flat back type lipped front urinal basin 430x260x350mm

size with automatic flushing cistern with standard flush pipe and CP brass spereaders with brass

unions and GI clamps complete including painting of fittings brackets, cutting & making good the

walls and floors wherever required

b) 17.4.2 Range of two urinal basins with 5 ltrs. White PVC automatic flushing cistern Each 1.00 4652.8 4652.80

Providing and fixing wash basin with CI brackets, 15mm CP brass pillar taps, 32mm CP brass

3 17.7 waste of standard pattern, including painting of fittings and brackets cutting & making good the

walls, wherever required

4 17.7.1 White vitrious china wash basin size 630 x 450mm with a pair of 15mm C.P. brass pillar taps Each 12.00 1848.35 22180.20

Providing and fixing stainless steel A ISI: 304 (18/8) kitchen sink as per IS:13983 with CI brackets

17.1 and stainless steel plug 40mm including painting of fittings & brackets, cutting and making good

the walls wherever required.

17.10.1 Kitchen sink with drain board

5 17.28 Providing & fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete

17.28.1 Semi rigid pipe

6 17.29 Providing & fixing 100 mm sand cast iron grating for gully trap Each 15.00 24.6 369.00

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Providing and fixing 600 x 450mm bevelled edge mirror of superior glass (of approved quality)

7 17.31 complete with 6mm thick hard board ground fixed to wooden cleats with CP brass screws and Each 12.00 674.05 8088.60

washers complete.

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50cm

deep and 1.8cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase

8 8.1 cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 ( 1

cement: 2 coarse sand: 4 graded stone aggregte 6mm nominal size) aas per direction of Engineer-in-

chare and finished smooth

8.10.1 White Agria Marble Stone sqm 0.38 2670.75 1001.53

9 17.35 Providing and fixing soil, waste vent pipes

17.35.1.2 Centrifugally cast (spun) iron socketed pipe as per IS:3989.S&S pipe Mtr 68.75 857.30 58939.38

17.35.2.2 Centrifugally cast (spun) iron socketed pipe as per IS:3989. Mtr 125.00 744.50 93062.50

Providing and fixing MS holder-bat clamps of approved design to Sand Cast iron/cast iron (spun)

10 17.37 pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement: 2

coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and

making good the walls etc.

Providing and fixing bend of required degree with access door insertion rubber washer 3mm thick

bolts and nuts complete

17.38.1.2 Sand Cast iron S&S as per IS-3989 Each 12.00 353.25 4239.00

17.38.2.2 Sand Cast iron S&S as per IS-3989 Each 18.00 281.15 5060.70

12 17.39 Providing and fixing plain bend of required degree

17.39.1.2 Sand Cast iron S&S as per IS-3989 Each 20.00 296.35 5927.00

17.39.2.2 Sand Cast iron S&S as per IS-3989 Each 20.00 221.95 4439.00

13 17.57 Providing and fixing collars

17.57.1.2 Sand Cast iron S&S as per IS-3989 Each 34.38 238.25 8189.84

17.57.2.2 Sand Cast iron S&S as per IS-3989 Each 62.50 169.65 10603.13

Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron

pipes of diameter :

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes & fittings of

Providing and fixing trap of self cleaning design with screwed down or hinged grating with or

15 17.60 without vent arm complete, including cost of cutting and making good the walls and floors.

a) 17.60.2 a) 100mm inlet and 75mm outlet

17.60.2.2 Sand Cast iron S&S as per IS-3989 Each 28.00 838.85 23487.80

Painting sand cast iron/centrifugally cast (spun) iron soil, waste vent pipes and fittings with paint

16 17.65 of any colour such as chocolate grey or buff etc. over a coat of primer (of approved quality) for new

Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm

17.70.1 from the centre of the waste coupling, 77 mm breadth with 25 mm Each 15.00 403.30 6049.50

minimum water seal, weighing not less than 260 gms

Providing and fixing PTMT liquid soap container 109 mm wide, 125mm high and 112mm distance

18 17.71 from wall of standard shape with bracket of the same meterials with snap fitting of approved Each 12.00 180.10 2161.20

quality colour and make, weighing not less than 105 gms.

Providing and fixing PTMT towel rail complete with brackets fixed towooden cleats with CP brass

screws with concealed fitting arrangement of approved quality and colour.

450 MM long towel rail with total length of 495mm, 78mm wide and effective height of 88mm,

weighing not less than 170gms.

Providing and fixing water Jet spray with hose pipe and CP brass angle valve to be fitted with seat

cover of european water closet complete in all respect of approved quality

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for

hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the

20 18.7 pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC

solvent cement and testing of joints complete as per direction of Engineer in Charge.

Internal work - Exposed on wall

18.7.1 15 mm nominal outer dia Pipes Mtr 5.00 133.95 669.75

18.7.2 20 mm nominal outer dia Pipes Mtr 5.00 157.15 785.75

18.7.3 25 mm nominal outer dia Pipes Mtr 8.00 197.90 1583.20

18.7.4 32 mm nominal outer dia Pipes Mtr 14.00 252.65 3537.10

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

18.7.5 40 mm nominal outer dia Pipes Mtr 15.00 348.25 5223.75

18.7.6 50 mm nominal outer dia Pipes Mtr 15.00 514.35 7715.25

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for

hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe

21 18.8 with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC

solvent cement and the cost of cutting chases and making good the same including testing of joints

complete as per direction of Engineer in Charge.

Concealed work, including cutting chases and making good the walls etc.

18.8.1 15 mm nominal outer dia Pipes Mtr 42.00 218.65 9183.30

18.8.2 20 mm nominal outer dia Pipes Mtr 35.00 243.05 8506.75

18.8.3 25 mm nominal outer dia Pipes Mtr 30.00 297.95 8938.50

18.8.4 32 mm nominal outer dia Pipes Mtr 5.00 358.9 1794.50

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for

hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing

of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints

complete as per direction of Engineer in Charge.

External works:

18.9.3 25 mm nominal outer dia Pipes metre 9.00 185.15 1666.35

18.9.4 32 mm nominal outer dia Pipes metre 15.00 230.45 3456.75

18.9.5 40 mm nominal outer dia Pipes metre 18.00 309.6 5572.80

18.9.6 50 mm nominal outer dia Pipes metre 5.00 475.7 2378.50

Making connection of GI distribution branch with GI main of following sizes by providing & fixing

tee, including cutting and threading the pipe etc. complete.

24 18.17 Providing and fixing gun metal gate valve with CI wheel of approved quality (screwed end).

18.17.1 25mm nominal bore Each 7.00 372.95 2610.65

18.17.2 32mm nominal bore Each 7.00 450.9 3156.30

18.17.3 40mm nominal bore Each 4.00 546.05 2184.20

18.17.4 50mm nominal bore Each 1.00 780.6 780.60

Providing and fixing ball valve (brass) of approved quallity. High or low pressure, with plastic

floats complete.

a) 18.18.3 a) 25mm nominal bore Each 2.00 421.65 843.30

26 18.19 Providing and fixing gun metal non-return valve of approved quality (screwed end).

18.19.4 50mm nominal bore

27 18.21 Providing & fixing unplasticised PVC connection pipe with brass unions:

18.21.1 30cm length

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

18.21.1.1 15mm nominal bore Each 12.00 51.35 616.20

28 18.41 Providing & fitting sand of grading zone V or coarser grade alround the GI pipes in external work:

18.41.6 50mm diameter pipe Mtr 1.00 61.4 61.40

29 18.49 Providing & fixing CP brass bib cock of approved quality conforming IS 8931:

18.49.1 15mm nominal bore Each 39.00 397.5 15502.50

Providing and fixing CP brass stop cock (concealed) of standard design and approved make

confirming to IS: 8931.

Providing and fixing CP brass angle valve for basin mixer and gyser points of approved quality

confirming IS: 8931:

18.53.1 15mm nominal bore Each 15.00 449.35 6740.25

Providing and placing on terrace (at all floor levels) polythene water storage tank of approved

32 18.48 brand and manufacture with cover and suitable locking arrangement and making necessary holes

for inlet , outlet and overflow pipes but without fittings and the base support for tank.

Making khurras 45x45cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1

cement :2 coarse sand :4 graded stone aggregate of 20 mm nominal size ) over PVC sheet 1 m X1M

X400 micron finished with 12 mm cement plaster 1:3 (1 cement :3 coarse sand) and a coat of neat

cement rounding the edge sand making and finishing the outlet complete.

Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS 13592

34 12.41 Type A including jointing with seal ring conforming to IS 5382 leaving 10 mm gap for thermal

expansion i) single socketed pipe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised -PVC rain

water pipes by means of 50 X50X50 mm hard wood plugs ,screwed witjh MS screws of required

length including cutting brick work and fixing in cement morter 1:4 (1 cement :4 coarse sand) and

making good the walls etc. complete.

TOTAL FOR SCHEDULE ITEMS (WATER SUPPLY)

Providing and fixing 15mm C.P brass mixing fitting (C.P. wall mixer Tel. type) for Bath with C.P.

MR bend/Crutch complete. Including cutting and making good the walls wherever required .C.P. EACH 7.00 2073.6246 14515.37

brass mixing fitting.

D) SEWERAGE (INTERNAL):

Providing, laying & jointing glazed stoneware pipes grade 'A' with stiff mixture of cement mortar

in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate

40mm nominal size) alround SW pipes including bed concrete as per standard design.

Providing and fixing square - mouth SW gully trap grade 'A' complete with CI grating brick

38 19.4 masonry chamber with water tight CI Cover with frame of 300x300mm size (inside) the weight of

cover to be not less than 4.50 Kg) and frame to be not less than 2.70 Kg as per standard design.

a) 19.4.1 100x100mm size 'P' type

19.4.1.1 With FPS bricks class designation 7.5 Each 15.00 1256.35 18845.25

Constructing brick masonary manhole in cement mortar 1:4 (1 cement: 4 coarse sand) RCC top

slab with 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size),

fondation concrete 1:4:8 (1 cement: 4 coarse sand: 8 graded stone aggregate 40 mm nominal size)

39 19.7 inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with

floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement: 2 coarse

sand: 4 graded stone aggregated 20 mm nominal size) finished with a floating coat of neat cement

complete as per standard design.

Inside size 90 x 80 cm and45cm deep including CI cover with frame (light duty ) 455 x 610 mm

a) 19.7.1 internal dimensions total weight of cover and frame to be not less than 38 kg) (weight of the cover

23 kg and weight of frame 15 kg).

19.7.1.1 With FPS bricks with class designation 75 Each 14.00 7132 99848.00

40 19.8.1 Extra for depth of manhole

With FPS bricks with class designation 75 Each 5.00 4061.7 20308.50

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per

IS:10910 on 12mm dia steel bar comforming to IS:1786 having minimum cross section as 23mm x

25mm and over all minimum length 263 mm and width as 165mm with minimum 112mm space

between protruded legs having 2mm tread on top surface by ribbing or chequiring besides

41 19.16 necessary & adequate anchoring projections on tail length on 138mm as per standard drawing and Each 16.67 256.75 4279.17

suitabbe to with stend the bend test and chemical resistance test as per specifications and having

manufacture's permanent identification mark to be visible even after fixing, including fixing in

manholes with 30x20x15cm cement concrete block 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone

aggregate 20mm nominal size) complete as per design.

TOTAL FOR SCHEDULE ITEMS

E) EARTH WORK( INTERNAL PLUMBING WORK)

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Earth work in excation by mechanical means (hydraulic excavator)/manual means over areas

(exceeding 30cm in depth, 1.5 in width as well as 10 sq.mt in plan) including disposal of

excavated earth lead upto 50m and lift upto 1.5 m disposed earth to be levelled and neatly

a) 2.6.1 All kind of soil Cum 73.19 129.35 9467.60

Excavating trenches of required width for pipes, cables, etc. including excavation for sockets and

refessing of sides, ramming of bottom depth upto 1.5m including getting out the excavated soil,

43 2.10 and then returning the soil as required in layers not exceeding 20mm in depth including

consolidating earth deposited layer by ramming, watering etc. and disposing of surplus excavated

soil as directed within a lead of 50m.

a) 2.10.1 All kinds of soil

2.10.1.2 Pipes, cables etc. exceeding 80mm dia but not exceeding 300mm dia Mtr 190.00 101.4 19266.00

Filling available excavted earth (excluding rock) in trenches, plinth sides of foundations etc. in

44 2.25 layet not exceeding 20 cm in depth consolidation earth deposited layer by ramming and watering cum 19.00 83.8 1592.20

lead upto 50m and lift upto 1.5m

TOTAL B 888531.26

ELECTRICAL WORKS

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC

1 1.10 insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with

modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC

insulated copper conductor single core cable etc as required.

Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core

2 1.11 cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, Point 4.00 710.00 2840.00

suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single

core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated copper conductor single core

3 1.12 cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FR PVC insulated Metre 140.00 162.00 22680.00

copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FR PVC insulated copper conductor single core

4 1.13 cable in surface/ recessed medium class PVC conduit alongwith 2 Nos 4 sq. mm FR PVC insulated Metre 60.00 268.00 16080.00

copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC

5 1.14 insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as

b) 1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 400.00 206.00 82400.00

c) 1.14.9 4 X 6 sq. mm + 2 X 6 sq. mm earth wire Metre 100.00 358.00 35800.00

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Supplying and drawing following pair 0.5 sq mm FR PVC insulated annealed copper conductor,

6 1.18 unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE

7 1.19 insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing Metre 90.00 22.00 1980.00

surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in

8 1.21 surface/recess including cutting the wall and making good the same in case of recessed conduit as

Supplying and fixing following modular switch/ socket on the existing modular plate & switch

box including connections but excluding modular plate etc. as required.

a) 1.24.6 Telephone socket outlet Each 9.00 89.00 801.00

b) 1.24.7 TV antenna socket outlet Each 6.00 93.00 558.00

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch

box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box

excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for

modular switches in recess etc as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in

13 1.31 recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps Each 25.00 288.00 7200.00

modular switch, connection etc. as required. (For light plugs to be used in non residential

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in

14 1.32 recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 Each 8.00 366.00 2928.00

amps modular switch, connection etc. as required.

Erection of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS lamps per

fitting, complete with all accessories including connection etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent

17 1.41 fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including Each 81.00 69.50 5629.50

connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing

etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard

18 1.44 length (upto 30 cm) with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable etc. as Each 22.00 73.50 1617.00

Installation of exhaust fan in the existing opening, including making good the damage, connection,

testing, commissioning etc. as required.

20 1.51 Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes. Each 12.00 68.50 822.00

Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board

including drilling holes in cubicle panel, making connections, etc. as required.

Supplying and fixing following way prewired TP&N MCB distribution board of steel sheet for 415

volts on surface/ recess complete with loose wire box, terminal connectors for all incoming and

22 2.8 outgoing circuits, duly prewired with suitable size FR PVC insulated copper conductor up to

terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate,

interconnections, powder painted including earthing etc. as required.(But without MCB/ RCCB/

Supplying and fixing following way prewired vertical type TP&N MCB distribution board of steel

sheet for 415 volts on surface/ recess complete with loose wire box of sheet steel, dust protected,

duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar,

23 2.9 din bar for mounting MCB's, terminal connectors for all incoming and outgoing circuits, duly

prewired with adequate size of FR PVC insulated copper conductor upto the terminal connector/

neutral link, earthing etc as required (But without MCB/ RCCB/ Isolator). (Note : Prewired

vertical type MCB TPDB is normally used where 3 phase outlets are required.)

a) 2.9.6 6 way Double door Each 2.00 8810.00 17620.00

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker

24 2.10 suitable for inductive load of following poles in the existing MCB DB complete with connections,

testing and commissioning etc. as required.

b) 2.10.5 Three pole and neutral Each 4.00 723.00 2892.00

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual

25 2.15 current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing

MCB DB complete with connections, testing and commissioning etc. as required.

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth,

26 2.18 metal enclosed plug top alongwith 20 amps "C" curve, SP, MCB, in sheet steel enclosure, on surface Each 16.00 693.00 11088.00

or in recess, with chained metal cover for the socket out let and complete with connections, testing

and commissioning etc. as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing

27 5.2 masonry enclosure with cover plate having locking arrangement and watering pipe etc. with Each 3385.00

charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode,

28 5.9 including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing Metre 97.50

shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as

30 NS Supplying of light fittings complete with all standard accessories as required.

10W CFL Fitting Surface mounted down lighter as per Osram Product. No LEDCOMFO CEILING

10W 6000K 4x1 APAC or similar specification of other approved makes.

9W CFL. Fitting Recess mounted as per Osram Cat No.- LEDCOMFO DL 9W 6500K 18x1 EN or

similar specification of other approved makes.

42W LED Fitting Recess mounted as per Osram Product. No OPTV SKYL LL0401-865 42W VS2 or

similar specification of other approved makes.

12W CFL Fitting Surface mounted down lighter as per Osram Product. No PLATFORMA LED

12W13101/6500K 4x1 APAC or similar specification of other approved makes.

18W LED Box Type Fitting Surface mounted as per Osram Product. No LUXLINE LED BATTEN

18W 765 10x1 IN or similar specification of other approved makes.

20W LED Mirror Light Fitting Wall mounted as per Philips Product. No Ecomoods Wall light

f) (16926, antracit) with 20W E27 LED Osram Lamp or similar specification of other approved makes. Each 8.00 3339.81 26718.45

1x14W LED. Fitting Single Wall Bracket as per Philips Product. No myLiving Wall light (QWG305)

or similar specification of other approved makes.

8W LED Fitting Bulk Head Site as per Philips Product. No WT202W LED6S CW PSU S1 PC or

similar specification of other approved makes.

Supplying of approved make ceiling fan (BEE - 5 Star) of double ball bearing of the following sizes

31 NS and its all accessories suitable for operation on 230V single phase, 50 Hz, AC supply complete as

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST

DSR 2012 Qty for

SI.NO DESCRIPTION Unit Rate Amount

CODE NO. balanced work

Supplying installation, testing commissioning of Wall Fan of the following sizes and its all

32 NS accessories suitable for operation on 230V single phase, 50 Hz, AC supply complete as required.

Supplying of approved make Exhaust Fan of the following sizes and its all accessories suitable for

operation on 230V single phase, 50 Hz, AC supply complete as required.

Supplying installation, testing commissioning of telephone tag block or similar specification of

other approved makes. of the following sizes

Supplying & fixing of following capacity TP&N MCB inside the existing panel board with drilling

holes in cubicle panel, making connections, etc. as required.

Supply of ISI marked (IS:2878) Squeeze Grip carbon-di-oxide gas type fire extinguisher with

36 NS cylinder of 4.5 kg. capacity complete with suitable length hose and horn duly charged and ready Each 2.00 9253.24 18506.47

for use GI bracket for wall mounting etc. as required.

Supply of ISI marked (IS:13849) ABC dry powder 6 kg. fire extinguisher with cylinder fully

37 NS charged complete with bakelite horn discharge tube, GI bracket for wall mounting etc. as required. Each 2.00 4947.41 9894.82

Providing and fixing of 2W LED based Exit Sign Board (Bajaj BHEX 20 R AC or other makes of

similar specification) as complete required.

TOTAL C 1195149.56

Digitally signed by

NBCC PRIYA PRIYA KUMARI

KUMARI 21:29:00 IST