Provn of 01 x Guard room with toilet block at TCP-7 and Provn of 01 x Guard room with toilet near Sem Nala at Faridkot Mil Stn

Amount

Surface dressing including Trimming of Natural ground, rough excavated surfaces and filled up area to remove vegetation and/or small inequalities not exceeding 15 cm deep complete all as specified and directed by Engr-In-Charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out including baling/pumping /dewatering(if required) of water complete all as specified and directed by Engr-In-Charge.

Returning, filling in trenches including spreading, leveling watering and well ramming in layers not exceeding 25cm complete all as specified and directed by Engr-In-Charge.

Removing of surplus soil not exceeding 200 m and deposited where directed at a level not exceeding 1.50m above the starting point complete all as specified and directed by Engr-In-Charge.

M&L for PCC 1:4:8 type D2 40mm stone aggregate filling mass concrete in foundation complete all as specified and directed by Engr-In-Charge.

Material and labour for providing Reinforced Cement Concrete(Design Mix) M 25 using 20 mm graded aggregate as in foundation including rafts, footings, foundation beams, plinth beams, bases of columns etc complete all as specified and directed by Engr-In-Charge.

M & L for Applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m complete all as specified and directed by Engr-In-Charge.

Material and labour for providing Reinforced Cement Concrete (Design Mix) M 25 using 20 mm graded aggregate as in Columns, pillars, piers, posts and struts complete all as specified and directed by Engr-In-Charge.

Material and labour for providing Reinforced Cement Concrete (Design Mix) M 25 using 20 mm graded aggregate as in beams, cantilever, lintels over 1.5 m complete all as specified and directed by Engr-In-Charge.

Material and labour for providing Reinforced Cement Concrete (Design Mix) M 25 using 20 mm graded aggregate as in slabs supported on walls, beams and columns in floor, roof, landing, balcknies, conopies, decks, slab and in shelves and like complete all as specified and directed by Engr-In-Charge.

Material and labour for providing Reinforced Cement Concrete (Design Mix) M 25 using 20 mm graded aggregate as in Chajjas complete all as specified and directed by Engr-In-Charge.

M & L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; rough finished vertical or to batter complete all as specified and directed by Engr-In-Charge.

M & L Formwork to sides of pillars, posts, struts, piers, columns and stanchions rough finished vertical or to batter complete all as specified and directed by Engr-In-Charge.

M & L formwork to sides and soffits of floor or roof beams, beam hunching, girders, lintels, cantlievers, shelves including supports, etc for rough finished flat surfaces of concrete complete all as specified and directed by Engr-In-Charge.

M & L formwork to soffits of suspended slabs such as roof slabs, floor slabs, la ndings and similar work; not exceeding 200 mm thick (Horizontal or slopping) for rough finished flat surfaces of concrete complete all as specified and directed by Engr-In-Charge.

M & L of Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concretewalls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide fair finished surface complete all as specified and directed by Engr-In-Charge.

M & L Formwork to chullah hoods, chajjas, troughs and similar items including edges; rough finished flat surfaces of concrete complete all as specified and directed by Engr-In-Charge.

Material and labour for 10 mm dia and over TMT bars, cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed by Engr-In-Charge.

All as per above item here-in-before but 6 to 8 mm dia complete all as specified and directed by Engr-In-Charge.

M&L for hard core of broken brick of guage n.exc 63mm deposited spread and levelled in layer n.exc 15cm thick watered and well rammed to true surfaces as s complete all as specified and directed by Engr-In-Charge.

Material and labour for providing 75 mm thick cement concrete (1:3:6) type C2 using 40mm graded aggregate as in plinth protection surfaces even and smooth without using extra cement including provision of construction joints complete all as specified and directed by Engr-In-Charge.

M & L Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade A complete all as specified and directed by Engr-In-Charge.

M & L Cement concrete 100 mm thick type D-2, 1:4:8 (40mm graded aggregate) as in sub-floors, sub bases, floors and pavings, etc complete all as specified and directed by Engr-In-Charge.

M&L Machine cut kota stone slab as in flooring of 20-25 mm thick, set and jointed in cement slurry over & including screed of 20 mm thick in cement mortar (1:6) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and mirror type polishing complete all as specified & directed by Engr-In-Charge.

M&L Machine cut kota stone slab 20-25 mm thick as in skirting, set and jointed in cement slurry over & including screed of 15 mm thick rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and mirror type polishing complete all as specified & directed by Engr-In-Charge.

M & L brick work with fly ash bricks, straight or curved on plan exceeding 6 metre mean radius built in CM 1:6 complete all as specified and directed by Engr-In-Charge.

M & L Brickwork with flyash bricks, straight or curved on plan to any radius i n half brick thick walls, built in CM 1:6 complete all as specified and directed by Engr-In-Charge.

M&L rough cast over rendering of 10 mm thick on fair face of brick or concrete surface as in CM 1:4 all as specified and directed by Engr-In-Charge.(The rough cast mixture shall consist of crushed stone or fine gravel aggregate, coarse sand & cement in the ratio of 1:1:1 over rendering coat.)

Rendering 15mm thick in cement mortar 1:4 on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified & directed by Engr-In-Charge.

Rendering 15mm thick in cement mortar 1:6 on any face of Brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified & directed by Engr-In Charge.

M&L for 5 mm thick plaster on ceiling in cement mortar (1:3) finished even and smooth without using extra cement complete all as specified and directed by Engr-In-Charge.

Preparation of newly rough cast plastered surfaces of walls etc., and applying two coats of cement base paint complete all as specified & directed by Engr-In-Charge.

Preparation of newly plastered/ RCC surfaces of walls etc., and applying two coats of cement base paint complete all as specified & directed by Engr-In-Charge.

Preparation of newly plastered surfaces of walls etc., and applying three coats of white wash complete all as specified & directed by Engr-In-Charge.

Preparation of new plastered surfaces and applying three coats of white wash on ceiling as specified & directed by Engr-In-Charge.

M&L Preparation of new plastered surfaces of walls & applying two coats of oil bound distemper over chalk whitening complete all as specified & directed by Engr-In-Charge.

M & L Rendering 1:3 of mortar 10 mm thick for laying floor finishes with water proofing compound complete all as specified & directed by Engr-In-Charge.(WPC shall be measured seperately).

Supply only integral water proofing compound(WPC) complete all as specified and directed by Engr-In-Charge.

M & L Applying evenly a tack coat of blown bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces complete all as specified and directed by Engr-In-Charge.

M & L a coat of Bitumen primer for use in waterproofing and damp-proofing treatments @ 0.70 ltr/sqm all described in paras 11.44.5 of MES Schedule Part -I complete all as specified and directed by Engr-In-Charge.

M & L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and directed by engr-in-charge.

M & L for Two coats of 3 Mangoes Aluminium Paint (Make- Asian Paint) over APP membrane complete all as specified and directed by Engr-In-Charge.

Material and labour for steel framed work such as grills, gratings, etc, with ends of bars shouldered and or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walkways; railings; frame work of water tanks and similar work conforming to Fe-290. Gde-E-165 complete all as specified and directed by Engr-In-Charge.

S&F Factory made box type steel window with side hung shutter including pintol hinges & 2 Nos 150 mm MS tower bolts on each shutter complete with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed by Engr-in-Charge.

S&F Factory made box type steel window with side hung shutter including pintol hinges & 2 Nos 150 mm MS tower bolts on each shutter complete without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed by Engr-in-Charge.

M & L for 3 mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads (supplied alongwith shutters) in Squares n.exc 0.5 sqm each complete all as specified and directed by engr-in-charge.

M & L for 3.0 mm thick frosted glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and directed by engr-in-charge.

S&F Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed by Engr-inCharge.

M&L for two coats of synthetic enamal paint oversteel surfaces complete all as specified and directed by Engr-in-Charge.

S&F of 35 mm thick 2nd class hard wood plain framed panel shutters (two number of pannels) with pannels of timber flat on both sides (feather edges) or of vaneered partical board medium desnsity, wood partical board with commercial face veneers fitted to chowkats complete all as specified and directed by Engr-in -Charge.

S & Factory made 35mm thick 2nd class hardwood (Hollock), glazed and skeleton shutters open rebated and prepared to receive gauge /gauge etc (without sash bars), edges of framing plain chamfered or rounded fitted with cut and mixed beads for securing glass etc for doors, size of members as specified in clause 8.20 (a) of MES Schedule Part-I Section -8 complete all as specified and directed by engr-in-charge.

M&L preparation of new or previously untreated surface of wood or wooden based surface any description not other wise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed by engr-in-charge.

S & F Pressed steel rectangular frames for doors,with one or more rebate for size of frame 125X60 mm, necessary including necessary fixing lugs hinges lock strike plate ,over a shop coat of zinc chromate primer complete all as specified and directed.

S & F Pressed steel rectangular frames for doors,with one or more rebate for size of frame 105X60 mm, necessary including necessary fixing lugs hinges lock strike plate ,over a shop coat of zinc chromate primer complete all as specified and directed.

S&F Factory made box type mild steel ventilator and with one shop coat of zinc chromate primer ready for wire mesh/glass pan fixing complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 150mm long aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed by engr-in-charge.

S & F 125 mm long aluminium handles, fabricated type, anodised complete all as specified and directed by engr-in-charge.

S&F 100 mm long butt hinges, medium weight, cold rolled, mild steel and fixed complete all as specified and directed by engr-in-charge.

S & F Floor door stopper of aluminium , 75-100 mm cast iron body, with hard drawn steel spring complete all as specified and directed by engr-in-charge.

S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasps staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extuded sections or cast aluminium alloy and fixed complete all as specified and directed by engr-in-charge.

S & F 2nd class hardwood Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles n exc 200 cu. cm each complete all as specified and directed by engr-in-charge.

M & L Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match & including 15 mm thick screed in cement mortar (1:6) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed by engr-in-charge.

M & L Coloured glazed ceramic tile 450x300x7 mm/350x 250x 7mm/ 450X 350X 7 mm thick on vertical surface such as skirting / dados set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade over & including screed of 10 mm thick rendering in cement mortar (1:4) complete all as specified & directed by Engr-In-Charge.

S&F Vitreous china bowl half urinal flat back, size of 465 x 355 x 265mm white (minimum), with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws complete with flush pipe and half turn valve 15mm more all as specified and directed by Engineer - in - Charge.

S&F vitreous china wash basin, size 550x400mm white flat back including cutting for and pinning in ends of brackets or erecting stand including 32mm waste fittings, 15mm fancy type chromium plated pillar taps, cast copper alloy, with capstan heads, screwed down high pressure, with long screwed shanks and flynuts, screwed for iron pipe and chromium plated with long screwed shanks & fly-nuts, flange end bedded in red lead cement with PVC connections 15 mm size, 450 mm long with PTMT nuts and other end fixed complete all as specified and directed by Engineer in Charge.

S&F Mild steel galvanized tubing 15 mm bore medium grade with fittings to walls with hooks, ceiling or laid on floor complete all as specified and directed by Engineer in Charge.

S&F Mild steel galvanized tubing 20 mm bore medium grade with fittings to laid in trenches / walls with hooks, ceiling or laid on floor complete all as specified and directed by Engineer in Charge.

M&L of PVC (SWR) floor trap 75 mm bore plain with grating including jointing with solvent cement fixed to wall/laid in trenches etc complete all as specified and directed by Engineer in Chrge.

S & F PVC 10 ltr. Cap. valveless syphonic action type, flushing cistern, low level, white/ coloured with inlet, ball valve, float and handle including brackets and connection to pipe etc. fixed in repairs complete all as specified and directed by engr-in-charge.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 1000 Ltr capesity hoisted and fixed in position all as specified including PVC float valves, high pressure, with polythene float and fly nut complete screwed for 20mm bore iron pipe & dismantling existing water tankcomplete all as specified and directed by engr-in-charge.

S & F PVC (SWR) pipes 110 mm single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by engr-in-charge.

S & F PVC (SWR) bends any radius, 110 mm complete all as specified and directed by engr-in-charge.

S&F in repair looking mirror 6mm thick of size 600mm x 450mm on commercial ply wood 6mm thick with PVC/ wooden moulding beading fixed to wooden plugs with chromium plated brass screws and cup washers etc complete all as specified and directed by Engineer in Charge.

M & L PVC (SWR) 'P’ trap 110 mm size complete all as specified and directed by engr-in-charge.

M & L Vitreous china squatting pan, Orissa pattern, size 580x440mm white/ coloured with integral foot rests including flus pipe and connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete all as specified and directed by engr-in-charge.

S&F 15mm size, length 450 mm PVC connection with PTMT nuts complete all as specified and directed by engr-in-charge.

S&F bib taps, cast copper alloy with crutch or butterfly handle,chromium plated screwed down, screwed for 15mm bore of iron pipe or for brass ferrule and fixed all complete all as specified and directed by engr-in-charge.

S&F 15mm bore stop valve chromium plated ,screwed down high pressure with screwed both ends for GI out let/inlet pipe or for union including threading to existing pipes on both ends complete all as specified and directed by engr-in-charge.

S&F in repair 20 mm bore stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engineer in Charge.

S & F Swivel shower of PTMT any colour for fixing with 15mm pipe. (Minimum weight 40gms) complete all as specified and directed by Engr-In-Charge.

S & F Shower arm 15 mm size, 195mm long with bend of 45degree with flange of PTMT any colour including fixing to steel pipe complete all as specified and directed by engr-in-charge.

S&F Tubular towel rail, Brass chromium plated, 20mm dia, D type, 60cm long between flanges complete all as specified and directed by Engineer in Charge.

S&F PTMT shelf fixed with and including Chromium plated brass screw and plastic cleat complete all as specified.

S & F Hat pegs, solid body, 225mm to 300 mm complete all as specifed and directed by Engr-In-Charge.

S&F 15mm bore stop valve chromium plated with longshank and cup (concealed type) complete all as specified and directed by engr-in-charge.

S& F Stainless steel grating of any size with or without waste hole complete all as specified and directed.

M & L for cement Concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in coping, bed block of hold fast and splash stone complete all as specified.

M & L Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking complete all as specified and directed by engr-in-charge.

Material and labour 25 mm` sand filling under floors or in foundation including watering and consolidation as specified and directed by Engr-In-Charge.

M & L Machine pressed precast concerte interlocking paver block any shape and size conforming to IS-15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment all as specified and directed by Engr-In-Charge.

M & L Pre-cast cement concrete block in PCC 1:3:6 type C1 masonry with solid blocks, exc/n exc 10cm in width and setting in mortar 1:6. including necessary form work, on sides of roads including necessary excavation embedding blocks in ground to depth as directed and finishing exposed surface even and smooth complete all as specified and directed by Engr-In-Charge.

M&L for preparation new concrete/bricks surface of any description over 10cm girth or width, not otherwise described and applying two coat of synthetic enamel paint over one coat of primer complete all as specified and directed by Engr-In-Charge.

M&L Cement concrete (1:2:4) type B-1 using 12.5 mm graded stone aggregate as in lintels upto 1.50 m clear span, cills , steps, seismic and other similar bands, copings, kneelars, apex stones, bed plates, bed blocks of hold fasts etc including necessary form work complete all as specified & directed by Engr-In-Charge.

M&L for 1 : 3: 6 Type C2 ( 40 mm graded aggregsate) in foundation filling and mass concrete as in base fdn etc complete all as specified and directed & directed by Engr-In-Charge.

M & L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc. n exc 6m mean radius, built in CM 1:4 complete all as specified & directed by Engr-In-Charge.

M & L 1:2:4 (20 mm agg) Type B1 set in CM 1:4 landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces complete all as specified & directed by Engr-In-Charge.

M & L Reinforced concrete pipes, class NP2; 150 mm, laid and jointed complete with collars complete all as specified and directed by Engr-In-Charge.

M & L Concrete1:4:8 type D2 bed to drain pipes; 150 mm including packing under, and haunching against the sides of pipes after they arelaid and tested; incomplete all as specified and directed by Engr-In-Charge.

M & L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required

Point wiring complete with 1100 volts grade FRLS insulated unsheathed cable of copper conductor cable multi stranded of size 1.5 Sqmm single core including PVC rigid concealed conduit medium grade of suitable size (not less than 20mm dia) with all accessories such as bend reducers /MS hooks, MS junction boxes 2mm thick galvanized steel pressed sunken terminal boxes of suitable sizes for mounting of switches sockets, fan regulators etc covered with 2.8mm thick plastic laminate (Hylem/Anchor) top cover sheet of required colour fixed with brass screws and cup washers, painting terminal boxes inside and out side with one coat of red oxide primer including continuous earth wire of size 1.5 Sqmm PVC stranded copper conductor unsheathed, insulated stranded (Green colour) connected to common earth point dolly for One light point/call bell point/fan point to be controlled by one number one way PT switch complete all as specified and directed by Engineer in Charge.

All as per Srl item No. 99 here-in-before but on same board.

All as per Srl item No. 99 here-in-before but Switch socket combination (multi purpose) 5 Pin 5 Amps 230 volts point to be controlled by one switch and wiring with 1.5Sqmm PVC unsheathed copper conductor cable FRLS 1.5 Sqmm PVC insulated earth wire on independent board.

All as per Srl item No. 99 here-in-before Switch socket combination (multi purpose) 6 Pin 15 Amps 230 volts point to be controlled by one switch and wiring with 2.5Sqmm FRLS PVC unsheathed copper conductor FRLS cable 2.5 Sqmm PVC insulated earth wire on independent board.complete all as specified and directed by Engineer in Charge.

S&F PVC Lamp holder suitable for and including batten fittings suitable for LED Lamp 5 to 20 watts bulb with bakalite 20mm back plate etc complete all as specified and as directed by Engineer-in-Charge.

S&F LED bulb 1 x 10 watt Lamp having luminous efficiency warranty 2 years complete all as specified and directed by Engineer in Charge.

S&F complete set of tube light fitting, 1x18/20 watt LED (4 feet long) 230 volt, decorative ultra slim linear LED lighting fixture with environment friendly, energy efficient ready to use pack etc with all acessories such as LED adopter, decorative bipin holder, LED tube internally prewired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Engineer in Charge. Make: Bajaj cat No.BCLSB 18W LED or Havells/Phillips

S&F complete set of LED mirror light fitting 1 x 12 W to 17 W, 230 V, including LED lamp with driver complete suitable for fixation on wall with body retrofit corrosion resistant superior finish and without any cracks through holes with all accessories pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size as per specification & directed by Engineer-in-Charge.

S&F ceiling rose three terminals PVC polycarbonate isolated body with bakalite 20mm back plate complete all as specified and directed by Engineer-in-Charge.

S&F sub main wiring with two runs of single core PVC FRLS sheathed insulated copper cable of 6 sqmm size, multi stranded 1100 volts grade with PVC insulated FRLS copper wire 6sqmm for continous earth wire drawin into existing concealed conduit complete all as specified and directed by Engineer-in-Charge. Note ;- Two runs of 6 Sqmm copper cable and one run of 6 sqmm copper wire earth continuty conductor in existing conduit with accessories shall be measured as one length)

S&F switch Piano type single pole one way 5 Amp, 230 VAC supply complete all as specified and directed by Engineer in Charge.

S&F socket two in one, 5 Pin 5 Amps 230 VAC supply, complete all as specified and directed by Engineer in Charge.

S&F switch piano flush type single pole one way 15 Amps, 230 volts on laminated sheet top cover complete all as specified and directed by Engineer-in-Charge.(Note:-Sheet top cover included in point wiring)

S&F socket two in one, 5 Pin 15/16 Amps 230 VAC supply, complete all as specified and directed by Engineer in Charge.

S&F MCB DB double door of sheet metal TPN 4 way with 415 Volts complete with and including MCCB 63 /100Amps with fixed thermal magnetic setting with breaking capacity not less than 16 KA complete all as specified & directed by Engineer-in-Charge.

S&F MCB distribution board double door of sheet metal single pole and neutral 8 way with 200 amps rated bus bar 240 volts complete all as specified and directed by Engineer-in-Charge.

S&F MCCB 4 Pole, 415 V, 100 Amps with breaking capacity 16 KA complete all as specified and directed by Engineer-in-Charge.

S&F MCB single Pole 240 Volts 32 Amp C Series with breaking capacity 10 KA complete all as specified and directed by Engineer in Charge.

S&F MCB SP&N 240 Volts 32 Amp C Series with breaking capacity 10 KA complete all as specified and directed by Engineer in Charge.

M & L Earthing complete with galvanised iron earth plate electrode of size 600 x 600 x 6mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to and including 4mm dia (8 SWG) GI earth wire from earth plate to main switch board including necessary GI bolts, nuts, check nuts, washers, thimble etc to the extend 7.5 mtr as earth lead by means of GI bolts & nuts etc, connecting to LT panel wlith provision of charcoal and salt all as per electrical plate No 3 of SSR Part-I including water arrangement with GI pipe 20mm dia (medium grade) for watering and including funnel, wire mesh, RCC cover & frame, PCC (1:3:6) type C2 using 20mm graded crushed stone aggregate) as in earthing pit including necessary excavation and earth work, returning , filling, ramming and remove of soil to a distance not exc 50 mtr, make good to match with existing surface and testing on completion complete all as specified and directed by Engineer in Charge. Note : The unit rate including earthing lead & protection pipe upto 7.5 meter from top to earth plate.

Supply, fixing & hanging Energy efficient Ceiling fan (white colour) 1400mm sweep including electronic type regulator, AC single phase, 230V, including canopies, three Nos. blades down rod double ball bearing with capacitor 2.5 mfd and making connection with including PVC insulated PVC sheathed copper conductor flexible cable 3 core of suitable size from ceiling rose or connector to fan including marking of MES number, complete all as specified and directed by the engr-in-charge .

S & F exhaust fan 300mm sweep, 380 RPM trans air 70 Watt, with louver shutter suitable for operation on 220/230 volts, single phase , AC and complete all as specified & directed by Engr-in-charge.

Writing MES Nos (Black, Roman, Italic or Indian) n.exc 30cm height complete all as specified & directed by Engr-in-charge.

Supply, installation, commissioning and testing water storage heater (geyser) vertical type of 25 ltr capacity, ultathick stainless steel superior 304 Gde PUF insulation thermostate, thermal cut off, 1PX4 multifunctional safety valve technology, feroglas dry powder coating finish, suitable for to operate / function on AC 220 V, single phase having heating element of 2 KW capacity and high thermal cut-out, energy saving BEE 3 star rating including fixed along walls including grouting fastening & fixing nuts/bolts of sitable size (04 Nos) and connecting up inlet/ outlet with cold water PVC connection pipes and electric connections cable cord min 1.50m length with copper conductor cable 3 core and 3 pin plug 15/16 Amp, including making good the disturbed surfaces matching with existing complete all as specified and directed by the Engr-in-charge. Make :- Havells , Bajaj, Surya, V Gaurd, Usha, CG Note : PVC connection will be measured & paid separately.

Supply, fixing and testing LED street light fitting of 25 Watt fitted on 4 to 9 meter high octagonal pole 9 & 11 meter PCC/Swan neck pole including LED lamps complete with body robust, corrosion, resistant, superior finish and without any cracks or through holes, made in a single piece by high pressure die cast aluminium alloy including GI pipe bracket made out of 32mm bore pipe. The luminaries shall be monolithic construction totally enclosed dust and water proof with minimum IP-65 protection as per IS-10322-1982 (Part-I) with latest amendments and input voltage range 140-300V, AC, frequency 50-60 Hz, PF should be more than 0.9 with total harmonic distoration THD (I) less than 15%, cool white colour and lamp starting time should not be more than 10 second, Fittings should be provided upto 10 KV surge protection. Driver should be constant current constant voltage driver. Driver should also have high voltage with standing capacity upto 300V, AC double phase protection, no load, open circuit and short circuit protection. LED light fittings should be suitable for ambient temperature from - 10 degree centigrade to 50 degree centigrade and humidity level 10% to 90% RH. Covers should be polycarbonate/ toughened glass to ensure minimum IP 65 degree protection cover should not degrade due to heating and ageing. The efficient of LED luminaries system shall be more than 85 lumens per watt and must be certified by LM-79 test report complete all as specified and directed by Engineer-in-Charge. Make: Bajaj Cat No. 169821 BCLST25WLED or equivelant in Crompron/ Havells/Halonix/Philips Note :- (a) Bidder shall submit test report of LED street light fitting from accredited test laboratory for LM-79 (b) Bidder has to furnish a replacement warranty of 05 years for LED light fittings complete including lamps from the date of completion of CA. The product will be replaced free of cost in the following cases : - (i) Manufacturing defects, (ii) Failure due to mechanical and electrical impact, (iii) Drop in lumen (or lux at 1m) below 90% of claimed values of lumen (or lux at 1m) of the LED/ luminairies. (c) All LED light luminaire must meet the provision laid down in IS-16101, 16102 Part-I/II, 16103 Part-I, 16104, 16105, 16106, 16108/2012 and 15885 Part-II/ Section 13 (d) scope of work shall include supply and fixing street light fittings on poles which includes needful T & P and required accessories etc if any, complete including making connection, testing etc complete. No extra payment is admissible on these account. Note: Every light fitting will be warranty 5 years after completion of CA and replacement/defects as applicable should be complied/rectified within 7 days .

Supply and laying XLPE insulated stranded and PVC sheathed heavy duty armoured electric cable with stranded aluminium conductor 1100 Volts grade confirming to IS - 7098 (Part-I, 1988) cross sectional area 16 Sqmm 4 core including thimbles / lugs with and including passing through pipe along wall, under road crossing / Nallah / under floor etc complete all as specified and directed by Engineer in Charge. (Note : Earth work, sand cushioning, GI pipe protection and brick protection to be measured and paid seperately).

M & L for sand cushioning with dry coarse sand to under ground cable 23 cm thick, 8 cm thick below the cable and 15 cm thick after laying the cable complete all as specified and directed by Engineer-in-Charge. Note : Thickness after punning shall be considered for payment.

M & L for brick protection with old size sub class 'B' bricks laid flat , length of bricks across the route of underground cable complete all as specified and directed by Engineer-in-Charge.

Supply and fix GI pipe 40mm bore light grade with all fittings, laid in trenches / under roads, drain, paths, fixed to poles/ walls with Mild steel clamps, nuts, bolts and washers complete all as specified and directred by Engineer-in-Charge.

S&F GI tubing medium grade 25mm bore with all fittings and laid in trenches / fixed to wall/ceiling and laid in floors complete all as specified and directed by Engr-In-Charge.

S&f Gun Metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed 25mm dia of pipe complete all as specified and directed by Engr-In-Charge.

S&f Gun Metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed 20mm dia of pipe complete all as specified and directed by Engr-In-Charge.

M/s Balvinder Singh Engineer and Contractors