SPECIAL REPAIR TO BLDG NO P 7 16 OR LIVING AREA OF IDSR AND CERTAIN MINOR AND REVENUE WORKS AT MIL STN JAMMU UNDER AGE BR I OF GE SATWARI

Amount

Surface excavation n.exc. 30 cm deep and averaging 15 deep and getting out in any type of soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5M in depth for foundation etc or manholes,piers,shafts etc not exceeding 10 Sqm on plan and getting out in any type of soil complete all as specified and directed .

M&L for plain cement concrete 1:4:8, type D2 (using 40mm graded crushed stone aggregates) as in foundation, filling & mass concrete complete all as specified and directed.

Returning, filling in, including spreading, leveling ,watering and well ramming in layers not exc 25cm in any type of soil complete all as specified and directed .

M&L for Earth filling under floor including spreading, levelling, watering and well ramming in layers n exc. 25 cm thick complete all as specified and directed .

Removing excavated material or surplus soil not exc 50 meter and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed

M&L for RCC 1:1.5:3, type A1 (using 20mm gradded crushed stone aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete etc complete all as specified and directed .

M&L for RCC 1:1.5:3, type A1 (using 20mm gradded crushed stone aggregates) as in Columns, pillars, piers, posts and struts etc complete all as specified and directed .

M&L for RCC 1:1.5:3, type A1 (using 20mm gradded crushed stone aggregates) as in Beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and directed .

M&L for RCC 1:1.5:3, type A1 (using 20mm graded crushed stone aggregates) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies , shelves complete all as specified and directed.

M&L for RCC 1:1.5:3, type A1 (using 20mm graded crushed stone aggregates) as in chajjas complete all as specified and directed.

M&L for use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc complete all as specified and directed.

M&L for use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or slopping) fair finished flat surfaces etc complete all as specified and directed .

M&L for use and waste of formwork to chullah hoods, chajjas, troughs and similar items including edges etc complete all as specified and directed .

M&L for use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed .

M&L for use and waste of formwork to sides of pillars, posts, struts, piers, columns, and stanchions etc complete all as specified and directed .

M&L for use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs exc 10cm but n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide etc complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required , including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed .

M&L for Mild steel TMT bars 5 mm dia and over upto & including 10mm dia, as in stirrups, spacers and binders,cut to length bent to shape required including cranking, binding spirally for hooping for columns, hooking ends and binding with and including MS wire annealed not less than 0.9 mm dia or securining with clip complete all as specified and directed .

M&L for brick work with fly ash bricks using old size bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed .

M&L for brick work with fly ash using old size bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed

M&L for rendering 15mm thick in cement mortar 1:4 on surfaces other than fair faces of brick work and surface finished even and smooth without using extra cement complete all as specified and directed .

M&L for rendering 15mm thick in cement mortar 1:6 on fair faces of brick work and surface finished even and smooth without using extra cement complete all as specified and directed .

M&L for rendering 10 mm thick in cement mortar 1:3 on ceiling, surface finished even and smooth without using extra cement complete all as specified and directed.

Supply only liquid water proofing compound

M&L for hard core of gauge not exceeding 63mm using broken stone or boulders, deposited, spread and leveled in layers not exc 15cm thick, watered and rolled/rammed to a true surfaces complete all as specified and directed .

M&L for 25 mm thick PCC 1:2:4, type B-0 (using 12.5mm graded crushed stone aggregates) as in floor etc complete all as specified and directed .

M&L for 8 to 10 mm thick non skid, joint free, ceramic coloured tiles (square / rectengular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and Including 15 mm thick screed bed in cement mortar 1 :6 complete all as specified and directed .

M&L for Glazed digital ceramic coloured tiles 450x300x7 mm thick as in vertical surfaces such as skirting/dados etc, set and jointed in neat cement slurry & pointed in white or coloured cement to match the colour of tiles over and Including 10 mm thick rendering in cement mortar 1 :4 complete all as specified and directed .

M&L for rendering 20 mm thick in cement mortar 1:4 on concrete surfaces when concrete is still green, finished even and fair including mixing of water proofing compound as per manufacturer's instructions complete all as specified and directed Note :- Water proofing compound shall be measured and paid separately as supply only

M&L for water proofing treatment as below:-- (i) Applying a coat of bitumen primer 0.4ltr/sqm by the same membrane manufacturer of density at 25 degree C’ 0.87-0.89Kg/Litre and viscosity 70-160 CPS till the surface properly impregnates and insolvent oil primer evaporates completely. (ii) Applying a coat of blown 85/25 graded bitumen confirming to IS 702 @ 1.2 Kg/sqm. (iiI) Applying Polymeric Polypropylene polymer membrane “APP” (Atactic poly propylene polymer ) modified prefabricated five layer 3mm thick not less than 3.6 Kg/Sqm with 160 grams/sqm non woven polyster made at centre core reinforced laid with 75 mm side overlap and 100 overlap in length using butane torch with 10cm over laps which shall be thermo fused by flame complete all as specified and directed .

M&L for Applying two coats of aluminium paint over the APP membrane complete all as specified and directed.

S&F steel Ventilator ( N exc 0.70 Sqm) 1.25 mm thick Box type (Double Shutter) ERW hollow P section of size 60 mm x 25 mm single rebated comprises glazed & wire gauged skelton shutter ERW sec 50 mm x 20 mm and 1 mm thick with two Nos sash bar of T- section 20 mm x 3 mm complete welded to frame with one vertical mullion of ERW box type T- section of size 60 mm x 25 mm and 1.25 mm thick including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 four No for each window incl following fitting welded to frame shutter hold fast of 150 mm long of 12 mm x 3 mm FI made to shape 4 No, handle of Z section 20 mm x 25 mm x 100 mm long 1 No per leaf, MS tower bolt 150 mm long 2 No per leaf, Z sec 20 mm x 25 mm, 100 mm long stopper 1 No on per leaf, MS Pintal hinges of size 75 mm x 12 mm 2 No per leaf fabrication, 10 mm Square bar gril, specing of gril 100 mm center to center and fixing arrangement as per drg No CEPZ/TD-324,325/0 ( Note:- Gril shall be measured and paid separately)

S&F Mild Steel framed work such as grills, gratings etc. with ends of bars shoulderd and/or riveted, or forged into spikes, framed guard bars, barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks,cooler stand,ladder and similar work conforming to Fe290, Gde-E-165 complete all as specified and directed..

S&F 3 mm thick figured glass, pin head/frosted type and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and directed .

M&L for 50 mm thick cement concrete 1:3:6 type C1( using 20mm graded crushed stone aggregates) as in plinth protection/path finishing surfaces even and fair complete all as specified and directed

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with sainless steel staples complete all as specified and directed

S&F Solid PVC door frame of size 50x47mm, made out of 5mm plain coloured PVC sheet reinforced with MS square tube complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick ( style ) consisting of frame work made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour P.V.C‘ C’ channel having a PVC sheet strip 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail on either side and as gap inserts for top rail; and bottom rail paneling of plain, colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rail with suitable PVC sheets beading and jointed together with solvent cement complete all as specified and directed .

S&F aluminium alloy, anodised, sliding door bolt of length 250mm with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extuded sections or cast aluminium alloy and fixed complete all as specified and directed

S&F aluminium anodised barrel tower bolts,200 mm long of extruded section, fixed to doors with screws complete all as specified and directed .

S&F Aluminium anodised, cast type, handle 150 mm size complete all as specified and directed.

S&F Butt hinges 100mm extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 fixed with screws complete all as specified and directed.

M&L for cutting (in brick walls) chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sun shades, shelves, lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting exc 20cm girth complete all as specified and directed.

M&L for Steel water tubing of 15 mm bore, medium grade, galvanised with all fittings, fixed to wall or laid in floors complete all as specified and directed

M&L for Steel water tubing of 20 mm bore, medium grade, galvanised with all fittings, fixed to wall or laid in floors complete all as specified and directed

S&F Rotational moulded polyethylene water storage tanks of 1000 litres capacity,(cylindrical vertical with closed top) with plastic lid cover, triple layered, white, hoisted and fixed in position including PTMT Ball valves high pressure with epoxy coated Aluminium rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe, including making connections complete all as specified and directed

S&F 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed .

M&L 150 mm bore Double wall corrugated HDPE Pipes,stiffness class SN 8 with integral socket and necessary fittings laid in trenches complete all as specified and directed. .

M&L for Concrete bed to drain pipes of dia 150mm in cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) including packing under and haunching against the sides of pipe after laid & tested including necessary formwork complete all as specified and direced .

S&F UPVC (SWR) pipes single socketed, 110 mm dia, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed .

S&F UPVC (SWR) pipes single socketed, 75 mm dia, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed .

S&F UPVC (SWR) bends any radius, 110 mm dia complete all as specified and directed .

S&F UPVC (SWR) bends any radius, 75mm dia complete all as specified and directed .

S&F UPVC (SWR) junction single, (Single T) equal or unequal, 110 mm bore complete all as specified and directed .

S&F UPVC (SWR) junction single, (Single T) equal or unequal, 75 mm bore complete all as specified and directed .

S&F UPVC (SWR) reducers 110 mm bore complete all as specified and directed

S&F UPVC (SWR) vent cowl 75 mm bore complete all as specified and directed .

S&F UPVC (SWR) floor trap, plain with grating including jointing with solvent cement, 75 mm dia complete all as specified and directed .

S&F bib tap long body, fancy type,chromium plated, with crutch or butter fly handle, screwed down, screwed for 15mm bore pipe & fixed complete all as specified and directed .

S&F 15mm dia angle valve/stop valve,fancy type ,cast copper alloy, chromium plated, concealed type with long shank and cup , screwed both ends for iron pipe complete all as specified & directed .

S&F angle valve with flange, cast copper alloy,fancy type,chromium plated, screwed down for high pressure with crutch or butter fly handle, screwed both ends for iron pipe of 15mm bore complete all as specified and directed .

S&F brass chromium plated tubular towel rail 20mm dia, D type, 600mm long between flanges fixed with CP brass screws including wooden/plastic beads complete all as specified and directed.

S&F vitreous china Wash hand basin, white, flat back of size 580x450mm including cutting for and pinning in ends of brackets or erecting stand including Cast iron brackets,Brass chromium plated waste coupling 32mm bore, Waste pipe PVC 32mm bore and PVC connection 15mm size, 450mm long with PTMT nut and other end fixed complete all as specified and directed.

S&F full pedestal for WHB complete all as specified and directed .

S&F Vitreous china half stall Urinal of size 340x280x490mm, white including providing and fixing plugs, bedding urinal against wall in CM 1:2 securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, flush pipe, grating and union for discharge pipe and Brass chromium plated waste coupling 32mm bore, Waste pipe PVC 32mm bore complete all as specified and directed.

S&F Vitreous china wash down water closet white colour of Size 520x360x390mm with 'S' trap, closed pattern with flat bottom including seat cover complete all as specified and directed .

S&F vitreous China squatting pan 'Orissa pattern', size 580mm x 440mm white / coloured, with integral foot rest including flush pipe and connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floors complete.all as specified and directed..

S&F 10 litres PVC,valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float,32mm PVC bend and handle including brackets complete all as specified and directed.

S&F stainless steel lock grating plain/hole ,100 mm dia including embeding in tiles with white cement complete all as specified and directed .

S&F brass chromium plated tubular towel ring of 150mm dia, fixed with CP brass screws including wooden/plastic beads complete all as specified and directed.

S&F Chromium plated soap dish of size 160x160x90mm, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F chromium plated hand shower (health faucet) with 8mm dia 1.20m long flexible tube and wall hook, complete all as specified and directed .

S&F PVC connection 15 mm x 600 mm including PVC check nut at both ends complete all as specified and directed .

S&F pillar taps,chromium plated ,cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe of 15mm bore complete all as specified and directed

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F corner glass shelf of size 30cm with Chromium plated bracket guard and railing fixed with and including screws and wooden/plastic cleats complete all as specified and directed

S&F Overhead Shower 125 mm dia round shape single flow with shower arm complete all as specified and directed .

M&L for Septic tanks complete for 25 users having excavation in any type of soil, PCC 1:2:4 as in foundation concrere, brick work with sub class 'B' bricks in cement mortar 1:4, including RCC precast cover slab embedded all around cover with angle iron frame, vent shaft and sludge chamber etc complete all per Drg No- CEPZ-TD/013/13) complete all as specified and directed.

M&L soakage well of size 2.40 mtr dia x 3.0 mtr deep,having excavation in any type of soil, PCC 1:3:6 in foundation , brick work with sub class 'B' bricks in cement mortar 1:4 including honey coming as per drawing, RCC cover slab , filling with brick bats complete all per Drg No- CEPZ-TD/013/13) complete all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) as in sub base to floors complete, all as specified and directed .

M&L for Cement concrete tiles 30cm x 30cm x 25mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished with grey cement and no pigment over and including 15mm thick screed bed or bedding layer in cement mortar 1:4 for laying finishes,complete all as specified and directed

M&L for PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) as in coping,bed blocks and similar works including slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregates) as in surface channel and drain including all necessary form work complete all as specified and directed.

M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc.complete all as specified and directed .

M&L for preparing newly plastered surfaces of wall and applying two coats of cement base paint over a coat alkali resistant priming paint complete all as specified and directed .

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over two coats of wall care putty of 1mm thick each & one coat of primer complete all as specified and as directed .

M&L for preparation of new ceiling surfaces and applying three coats of white wash complete all as specified and directed .

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description having width/girth exceeding 10 cm including preparation of surfaces by rubbing with sand paper to make surface even and smooth complete all as specified and directed .

M&L for applying two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces of any description having width/girth exceeding 10 cm including preparation of surfaces and necessary filling by chalk putty as and where required to make surface even and smooth complete all as specified and directed .

S&F Pre- painted galvalume aluminum zinc coating ( AZ-150) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in curved roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed .

S&F Pre-painted galvalume aluminum zinc coating (AZ-150) GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed .

M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel, gusset plates, or flat sections) including distance pieces, cleats etcFe 410 -W (GdeE- 250) quality 'A' complete all as specified and directed

M&L for Plates (plain ) channels, square cut or notched, gusset plates, base plate (ordinary and counter sunk) forming holes, without any attachment Fe 410 -W (Gde- E- 250) quality-A complete all as specified and as directed by Engr-in-Charge

M&L for structural steel tubing ,medium class as in main and cross beams, vertical post, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to latest IS specifications complete all as specified and directed .

S&F Pressed steel frames of size 105 x 60mm made of size 1.25mm thick MS sheet for door with one or more rebates including lugs, hold fast, lock strike plate etc complete including PCC 1:3:6 type C1 as in back fill to chowkats complete all as specified and directed .

M&L for 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed

M&L for preparation of newly plastered or unplastered surfaces of wall and applying three coats of white wash complete all as specified and directed .

Taking down chowkats or frames with shutter without taking off shutter from the frame n. exc 1.5 sqm each including cutting holes for taking out hold fast or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) complete all as specified and directed .

Taking down chowkats or frames with shutter without taking off shutter from the frame exc 1.5 sqm & n. exe 4 sqm each including cutting holes for taking out hold fast or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) complete all as specified and directed .

Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillars etc and removing unserviceable material to a distance exc 100 mtr complete all as specified and directed .

Demolition of cement concrete (un-reinforced) in ground floor to 4th floor and pavings n. exc 15 cm thickness (below or above ground level ) and removing unserviceable material to a distance exc 100 mtr complete all as specified and directed .

Demolition of reinforced cement concrete of any discription in ground floor to 4th floor and removing unserviceable material to a distance exc 100 mtr complete all as specified and directed .

Dismantling posts or struts (wood, steel or RCC) of any section, including taking out embedded portion in concrete, brick work etc and making good the disturbed ground complete all as specified and directed .

Taking down cement plaster from brick walls /ceiling or concerete of any description, raking out joints, hacking for key, scrubbing down with water etc and removing unserviceable material outside the premises complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed .

S&F Pressed steel frames of size 125 x 60mm made of size 1.25mm thick MS sheet for door with one or more rebates including lugs, hold fast, lock strike plate etc complete including PCC 1:3:6 type C1 as in back fill to chowkats complete all as specified and directed .

S&F 35 mm thick 2nd class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); fitted to chowkats complete all as specified and directed

S&F 150 mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed .

S&F in repair mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate fixed with welding complete all as specified and directed .

S&F in repair 25mm outer dia stainless steel decorative drapery rod of 20-22 gauge and with stainless steel brackets near to ends with stainless steel finials at both ends including necessary fittings complete all as specified and directed .

S&F steel window 1.25 mm thick Box type (Double Shutter) ERW hollow P section of size 60 mm x 25 mm single rebated comprises glazed & wire gauged skelton shutter ERW sec 50 mm x 20 mm and 1 mm thick with two Nos sash bar of T- section 20 mm x 3 mm complete welded to frame with one vertical mullion of ERW box type T- section of size 60 mm x 25 mm and 1.25 mm thick including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 four No for each window incl following fitting welded to frame shutter hold fast of 150 mm long of 12 mm x 3 mm FI made to shape 4 No, handle of Z section 20 mm x 25 mm x 100 mm long 1 No per leaf, MS tower bolt 150 mm long 2 No per leaf, Z sec 20 mm x 25 mm, 100 mm long stopper 1 No on per leaf, MS Pintal hinges of size 75 mm x 12 mm 2 No per leaf fabrication, 10 mm Square bar gril, specing of gril 100 mm center to center and fixing arrangement as per drg No CEPZ/TD-324,325/0 complete all as specified and directed . ( Note:- Gril to be measured and paid separately)

S&F 3 mm thick sheet glass ordinary ,quality glazing with steel pins,oil putty to steel windows and beads, nails etc to wooden surfaces as in square exc 0.50 sqm in each pane complete all as specified and directed .

S&F in repair pillar taps,chromium plated ,cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe of 15mm bore complete all as specified and directed

S&F in repair angle valve with flange, cast copper alloy,fancy type,chromium plated, screwed down for high pressure with crutch or butter fly handle, screwed both ends for iron pipe of 15mm bore complete all as specified and directed

S&F in repair bib tap long body, fancy type,chromium plated, with crutch or butter fly handle, screwed down, screwed for 15mm bore pipe & fixed complete all as specified and directed .

S&F in repair 15mm dia stop cock,fancy type ,cast copper alloy, chromium plated, concealed type with long shank and cup , screwed both ends for iron pipe complete all as specified & directed .

S&F in repair brass chromium plated tubular towel ring of 150mm dia, fixed with CP brass screws including wooden/plastic beads complete all as specified and directed.

S&F in repair Chromium plated soap dish of size 160x160x90mm, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail 20mm dia, D type, 600mm long between flanges fixed with CP brass screws including wooden/plastic beads complete all as specified and directed

S&F in repair Overhead Shower 125 mm dia round shape single flow with shower arm complete all as specified and directed .

S&F in repair vitreous china Wash hand basin, white, flat back of size 510x400mm including cutting for and pinning in ends of brackets or erecting stand including Cast iron brackets,Brass chromium plated waste coupling 32mm bore, Waste pipe PVC 32mm bore and PVC connection 15mm size, 450mm long with PTMT nut and other end fixed complete all as specified and directed.

S&F in repair full pedestal for WHB complete all as specified and directed

S&F in repair 10 litres PVC,valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float,32mm PVC 'L' bend and handle including brackets complete all as specified and directed.

M&L for 16 to 18 mm thick Granite black (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed

S&F in repair vitreous China squatting pan 'Orissa pattern', size 580mm x 440mm white / coloured, with integral foot rest including flush pipe and connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floors complete.all as specified and directed..

Taking down or up 15 mm dia steel tubing and connections including cleaning for refixing or removel complete all as specified and directed.

Taking down or up 20 mm dia steel tubing and connections including cleaning for refixing or removel complete all as specified and directed.

Dismantling PVC/Cement/CI pipes 50 to 110 mm dia including all fittings and removing from site complete all as specified and directed .

M&L in repair for providing precast cement concrete 1:2:4, type B-0 (using 12.5mm graded crushed stone aggregates) as in louvers and jallies, 40mm thick (measured solid) including all moulding but excluding frame and set in cement mortar 1:4 complete all as specified and directed.

M&L for 8 to 10 mm thick virified ceramic (double charged) tiles, any shade & colour (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm as in floors etc. using 4 mm spacers, set and jointed in neat cement slurry and pointed in white or coloured tile epoxy grout as per the manufacturer specifications to match over and including 15 mm thick screed bed or bedding layers in cement morar 1:4 complete all as specified and directed .

M&L for 8 to 10 mm thick virified ceramic (double charged) tiles,any shade & colour (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm as in vertical surfaces such as skirting, dado etc. using 4 mm spacers, set and jointed in neat cement slurry and pointed in white or coloured tile epoxy grout as per the manufacturer specifications to match over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed .

M&L for 75 mm thick plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in sub base to floors complete, all as specified and directed .

Providing and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade of approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc of required strength, thickness & size/ shape made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

Removing old brick tiles/ RCC padding including mud phuska and removing from site and clean the surface of roof with water and remove dust complete all as specified and directed .

Complete removal of existing water proofing treatment of any description including under layer, taking down of cement plaster / demolition of cement concrete of any thickness and removal of debris off the premises including grubbing up of trees and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water to remove all loose dirt/dust and applying roof treatment as below:-- (i) Applying a coat of bitumen primer 0.4ltr/sqm of density at 25 degree C’ 0.87-0.89Kg/Litre and viscosity 70-160 CPS till the surface properly impregnates and insolvent oil primer evaporates completely. (ii) Applying a coat of hot blown 85/25 graded bitumen confirming to IS 702 @ 1.2 Kg/sqm. (iiI) Applying Polymeric Polypropylene polymer membrane “APP” (Atactic poly propylene polymer ) modified prefabricated five layer 3mm thick not less than 3.6 Kg/Sqm with 160 grams/sqm non woven polyster made at centre core reinforced laid with 75 mm side overlap and 100 overlap in length using butane torch with 10cm over laps which shall be thermo fused by flame complete all as specified and directed .

M&L for PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregates) as in padding over roof, finished and laid to required slope complete all as specified and directed .

M&L for preparation of old decorated concrete/ plastered surfaces of walls, pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots & rubbing with sand paper and applying one coat of oil bound distemper including necessary filling of wall care putty on uneven surface as and where required complete all as specified and directed .

M&L for preparation of old plastered surfaces of walls, & applying two coats of oil bound distemper over one coat of wall care putty of 1 mm thick complete all as specifieds and directed .

M&L for preparation of old decorative plastered/concreat surface of wall, chajja, facia, face of columns, beam etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots & rubbing with sand paper and applying one coat of weather proof exterior emulsion (APEX) with necessary scaffoding up to 4th storey, including necessary filling of wall care putty on uneven surface as and where required complete all as specified and directed .

M&L for preparation of old decorated plastered /concrete/ brick surfaces of walls (up to 4th storey with necessary scaffolding) and applying two coat of cement based paint complete all as specified and directed .

M&L for preparation of old decorated ceiling surfaces and applying two coats of white wash complete all as specified and as directed .

Taking down carefully existing aluminium/copper point wiring for light, fan, socket or power bell complete with fittings such as Switches, sockets, ceiling roses, holders, call bells etc & making good the disturbed surfaces of walls/ceiling, matching the colour with existing surface complete all as specified and directed. Note : Rate for making good shall be deemed to be included in above item rate.

Taking down of unserviceable MCB DB, DP /TPN along with MCB's complete all as specified and directed

Point wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable(ISI marked) 1100 volts grade FRLSH with multistranded copper conductor, drawn through concealed / surface in wall / roof/ceiling surface and its accessories on the surface etc including PVC rigid concealed conduit of suitable size with all accessories such as bend, reducers, MS hooks including modular galvanised flush boxes of suitable size and white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc including continuous earth wire of size 1.5 Sqmm PVC FRLSH stranded copper conductor unsheathed, insulated, stranded connected to common earth point dolly for one light point/fan point/call bell point, 230 volts controlled by one switch complete all as specified and directed . Note:- Proper colour coding is to be followed as per IS specifications.

All as per Srl item No 147. here-in-before but for one socket outlet, 3 Pin 5 Amps, 230 Volts on independent board complete all as specified and directed

All as per Srl item No.147 here-in-before but for one three pin socket outlet 5 Amp on the same board with other switches complete all as specified and directed

All as per Srl item No 147 here-in-before but for one 3 pin socket outlet 16 Amp independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire complete all as specified and directed

S&F modular type switch, one way 6 Amps , 1 module complete all as specifieds and directed .

S&F modular type socket 3 pin, 6 Amps, 2 module complete all as specifieds and directed .

S&F modular type switch, one way, 16 Amps, 1 module complete all as specifieds and directed .

S&F modular type socket 3 pin, 6 A/16 Amps, 2 module complete all as specifieds and directed .

S&F modular type fan regulator,120 Watt, 2 module complete all as specifieds and directed .

S&F ceiling rose, surface backelite, three terminal, 240 volts complete all as specifieds and directed .

S&F LED light fitting 1 x 18Watt, 220V, Integrated batten type with driver, holder including LED tube light, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose with all fixing arrengenment complete all as specifieds and directed . . Note:- The LED batten and LED tube rod shall be of same make.

S&F lamp holder,PVC /Polycarbonate type with back plate for batten fittings complete all as specifieds and directed . .

S&F LED lamp of capacity 10 Watt suitable for B22 holder complete all as specifieds and directed . . .

S&F energy saving new generation 10W LED bulk head luminaire with opal diffuser, IP 65 and including connecting up with twin core twisted flexible copper coductor cable with suitable size of 230 volt,50 Hz complete all as specified and directed.

S&F Sheet metal enclosure for DBs,SPN, double door,IP-43 protected, 230 Volts,4 ways with 200 amps rated copper bus bar complete all as specified and directed

S&F switch piano, flush type, single pole, one way, 5/6 Amps, 230 volts, AC supply complete all as specified & directed

S&F socket outlet, 2 in 1, 3 pin, 6 Amps, 230 volts ,AC supply complete all as specified & directed

S&F switch piano, flush type, single pole, one way, 16 Amps, 230 volts, AC supply complete all as specified & directed

S&F socket outlet, 3 pin, 16 Amps, 230 volts ,AC supply complete all as specified & directed

S&F Sheet metal enclosure for DBs,SPN, double door,IP-43 protected, 230 Volts,8 ways with 200 amps rated copper bus bar complete all as specified and directed

S&F MCB Single pole, 6 to 32 Amp, 240 Volts with rupturing capacity 10 KA, 'C' series, complete all as specifieds and directed .

S&F MCB DP, 32 Amp, 240 Volts with rupturing capacity 10 KA, 'C' series, complete all as specifieds and directed .

Taking down existing ceiling fan of any size/sweep including oiling, greasing, cleaning and applying two coats of synthetic enamel paint after preparation of surface and refixing the same complete all as specified and directed .

S&F exhaust fan, steel body, AC single phase. 230 V of size 300 m sweep with, blades and frame and louvers, hanging on wall with 4 Nos steel fasterners 10mm dia & 100mm long including wall hole and making good the disturbed surfaces as per existing complete all as specified & directed

S&F electric water heater of capacity 25 litres,BEE 5 Star rated,storage type, steel body vertical type with glass lined /porcelain enamel coated steel inner tank and glass line double ceramic heating element upto 2 KW complete with all accessories such as safety valve,thermostate NRV,connection piece etc and fixing with 04 Nos nut bolt grouting in wall in PCC(1:2:4) using 12.5mm graded stone aggregate for hanging the geyser and making good the disturbed surface complete all as specified and directed

M&L for complete earthing with galvanised mild steel earth plate electrode of size 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC 1:2:4 type B-1, precast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh ,15mm dia light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specifieds and directed ..

S&F ceiling fan complete with blades, modular fan regulator of 120 wattage compatible with BLDC fan, clamp, hooks and accessories, 230 V, 1200 mm sweep, min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor(BLDC) and fixing of hooks by anchor fastner complete all as specified and directed .

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable, cross sectional area 25 Sqmm, 2 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete including taking out old cable & bricks all as specified and directed. Note: (i) Returning filling, earth work, sand cushioning and cable cover for protection of cable shall be measured and paid separately.

All as per Ser item No 174 here-in-before but cable of size 10 sqmm 2 core

M&L for sand cushioning with a layer of dry river sand, 80mm thick before laying of cable and 150mm thick (punned down to 100mm thick) after laying of cables, in trenches/ducts, complete all as specified and directed. Note : Punned down thickness (overall 18cm), shall be considered for measurement and payment.

M&L for factory made unreinforced precast concrete cable cover LV type-1, flat, of size 250x150x40mm, laid flat and dry in trenches over the cable for protection, length perpendicular to the direction of cable adjacent to each other, complete all as specified and directed.

S&F Galvanised steeI tubing, light grade, 40mm bore, for cable protection, fixed to pole/wall with MS clamps, nuts, bolts etc or laid under floor/road/pavement complete all as specified and directed.

M&L for cutting existing cast iron/GI pipe in position for insertion of CI specials or GI fittings viz Tee, collar, bend or tail piece etc for 80 to 200 mm bore pipe including removing of blockage, cleaning of pipe line complete all as specified and directed

S&F Galvanised steeI tubing,25mm bore, medium grade with all fittings , fixed to wall/ceiling or laid in floors/trenches complete all as specified and directed

S&F 25mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed .

M&L for construction of Valve pit of size 600mmX600mmX750mm (internal dimensions) (Type-B) with brick masonry construction including necessary excavation and earth work in any type of soil , brick work in cement mortar 1:4,15mm thick plastering in cement mortar 1:4, three coats of white wash, PCC coping in 1:2:4 Type B-1 and provn of 50 mm thick precast RCC 1:2:4 type B1 valve pit cover with handle complete all as specified and as directed by Engr-in-Charge

J P TECHNO (BID ID -3147762)

M/S ANIL MAHAJAN (BID ID -3150688)

AMRIT ENTERPRISES (BID ID -3156106)

STAR CONSTRUCTIONS (BID ID -3150440)

THAKUR BUILDERS AND CO (BID ID -3155967)