REPAIR REPLACEMENT OF TILING JOINERY PLUMBING AND SANITARY FITTINGS INCLUDING PETTY REPAIRS WORK AT SECTOR D UNDER AGE BR I OF GE 865 EWS

Amount

Demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness (below or above ground level) and Removing demolished material to a distance and depositing out site of MoD land Where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) of any description and in any position not other wise specifically provided for and removing debris outside the MoD land complete all as specified and directed by Engr-in-Charge

Demolition of reinforced cement concrete of any description and in any position not other wise specifically provided for and Removing demolished material to a distance and depositing out site of MoD land Where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tile to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed.

Demolition of bricks (laid flat or on edge) or interlocking tiles in floors, channels, kerbes, aprons, etc laid dry of laid dry and pointed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles/concrete block walling complete all as specified and as directed by Engr-in-Charge.

Taking down cement or cement lime plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, including cutting of trees, shrubs or any type of vegitation upto and including roots complete all as specified and directed by Engineer-in-Charge.

Material & Labour 75mm thick PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in plinth protection and finished concrete surface even and smooth without using extra cement including making proper joints with bitumen mastic with sand as per specification at an interval of 3m complete all as specified and as directed.

M&L for plain cement concrete 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) 100 mm thick sub base, sub floors, hard standing and pavings complete all as specified and directed.

Forming Contraction (Dummy) Joints 65 mm deep x 10 mm wide, filled with sealing compound grade A, complete all as specified and directed.

M&L for plain cement concrete 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) 75 mm thick sub base, sub floors and pavings complete all as specified and directed.

M&L for Vitrified ceramic tiles 10 mm thick (ligh shade) (square/ rectangular), first quality, polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed or bedding layer in Cement Mortar 1:4 for laying floor tiles complete all as specified and directed.

M & L for joint free Non-Skid coloured Ceramic tiles, first quality, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed or bedding layer in Cement Mortar 1:4 for laying floor finishes complete all as specified and directed.

M & L for joint free Non-Skid coloured Ceramic tiles, first quality, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed or bedding layer in Cement Mortar 1:4 for laying floor finishes complete all as specified and directed.

M&L for 300 x 200 x 7mm thick coloured glazed ceramic tiles, first quality, set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments.(Note: Any disturbed surfaces shall be matched w/o any extra cost to the govt) including 10mm thck screed bed below tile for dado/skirting CM 1:4 complete all as specified and as directed.

M&L for (350mm x 250mm x 7mm/450mm x 350mm x 7mm thick) coloured glazed ceramic tiles, first quality, set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments.(Note: Any disturbed surfaces shall be matched w/o any extra cost to the govt) including 10mm thck screed bed below tile for dado/skirting CM 1:4 complete all as specified and as directed.

M&L for Plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregates as in sub base, foundation, filling and mass concrete, complete all as specified and as directed by Engineer-in-Charge.

M&L dressed granite or trap stone as in Kerb stones roughly squared stones of size 20cm x 30 cm, so that the maximum depression from a straight edge held against the dressed surface shall not exceed 6mm for top and exposed surfaces of sides and 20mm for the rest of surfaces jointed in CM 1:6 and struck finish (rate included for removal of old damaged kerb stones of any description) complete all as specified and as directed.

M&L for plain cement concrete 1:5:10, type E-2 (using 40 mm graded crushed stone aggregate) 100 mm thick sub base, sub floors and pavings complete all as specified and directed.

M&L for plain cement concrete 1:2:4, type B-2 (using 40 mm graded crushed stone aggregate) 75 mm thick, as in floors and the like including finishing the surfaces even and fair without using extra cement complete all as specified and directed.

M&L for Machine pressed / vibro mechenically floated interlocking cement paver block ISI marked, any shape and size conforming to IS 15658-2006 of 60mm thickness, M-35 Grade, with topping of grey cement and pigment, laid over and including 50mm thick sand cushioning complete. Shape pattern of laying shall be approved by Engineer-in-charge.

M&L for cement concrete 1:4:8 type D1, (20mm graded crushed stone aggregate) 75 mm thick as in sub -floors ,sub- bases ,floors and pavings,etc complete all as specified and as directed.

M&L PCC 1:2:4, 40 mm thick type B1 using 20 mm graded crushed stone aggregate as in floor finished even and smooth without using extra cement complete all as directed by Engr-in-charge.

M&L for cement concrete 1:4:8 type D1, (20mm graded crushed stone aggregate) 100 mm thick as in sub -floors ,sub- bases ,floors and pavings,etc complete all as specified and as directed.

M&L for Chequred cement concrete tiles 20cm X 20cm X 25mm thick, set ,pointed & jointed in neat cement slurry in floors polished with grey cement & pigments laid over and including 20mm thick cement screed base (1:4) and all as directed by Engr-in -Charge.

Providing precast cement concrete 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate), as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting in mortar complete with joints to match complete all as specified and as directed.

TMT mild steel bars, 10 mm dia and over, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia), complete all as specified and as directed by Engineer-in-charge.

TMT mild steel bars, 6 to 8mm dia, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia), complete all as specified and as directed by Engineer-in-charge.

M&L for 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over and including 20 mm thick cement screed bed in CM 1:3 complete all as specified and as directed.

M&L for second class soft wood clean swan as in battens for grids of ceiling and lining, plain fillets exc 13 sqcm and n.exc 25 sqcm, square/ rectangular in section, secured with nails or brads to timber frame work including dismantlng fillets, rails, posts, rafters, purlins, grids for ceiling & wall panelling etc under 40 Sq.cm in section complete all as directed.

M&L for second class soft wood clean swan as in beading for edges of ceiling, lining, wooden flooring work, plain fillets exc 6 sqcm and n.exc 13 sqcm, square/ rectangular in section , secured with nails or brads to timber frame work including dismantlng fillets, rails, posts, rafters, purlins, grids for ceiling & wall panelling etc under 40 Sq.cm in section all as specified

M&L for covered fillets of standard hard board not less than 6mm thick and up to 40mm wide and fixing with screws complete all as specified and as directed

9mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work as in walls complete incluidng taking down old wall/ceiling board/ply wood all as specified and as directed by Engr-in-Charge.

9mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work as in ceiling complete incluidng taking down old wall/ceiling board/ply wood all as specified and as directed by Engr-in-Charge.

S&F 19mm dia mild steel, chromium plated curtain rods, with brackets, end bulbs, fixed in repairs, complete all as specified and as directed by Engr-in-Charge.

M&L 7mm thick printed PVC sheet in strips & channel feathered at edges for fixing on solid PVC wall lining, insulated PVC wall lining and solid PVC partition inclusive of solvent cement and fixing at site as per specifications including taking down old wall/ ceiling board/ ply wood and as directed by Engr-In-Charge

S&F 5mm thik PVC sheet fillets of width 35mm for wall panelling inclusive of fixing on wall to make PVC frame as per specification and drawing.

M&L French polishing on new wood or wood based surface of any width or girth or any description, including cleaning and preparing the surface including a coat of wood filler on new surface with two or more coats complete all as specified and as directed.

M&L for hard wood 2nd class factory made wooden boarded floors 10mm thick and skirtings planed one side & edges tonged and grooved or rebated , including backing with thermocol sheets or as specified by manufacture including dismantling boarding / wooden flooring of any description, fixed in any positon all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt), complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt), complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description area exceeding 1 Sqm and not exceeding 2 Sqm each, complete all as directed by Engr-in-Charge.

Taking down shutters of any description area not exceeding 1 Sqm each, complete all as directed by Engr-in-Charge.

Hacking out old broken glass (any thickness size/ quality description) from metal frame including punching or drilling out old glazing pin/spring clips and providing and fixing new one complete all as specified and directed.

Taking down wooden shutters of any description not exceeding 1.00 sqm, easing and adjusting and refixing the same in same opening with old builder's hardware as required complete all as specified and as directed bye Enginner-in-Charge.

Taking down wooden shutters of any description exceeding 1.00 sqm but not exceeding 2.00 sqm, easing and adjusting and refixing the same in same opening with old builder's hardware as required complete all as specified and as directed bye Enginner-in-Charge.

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frames for door, windows, ventilators with one or more rebates including joining cleat for fixed etc complete all as specified.

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium door shutter, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading screws etc complete all as specified and directed.

Anodised aluminium powder coated (minimum 50 micron thickness) windows and ventilator shutter, side hung type with out sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodized aluminium fittings such as 150 mm long peg stay (01 No), 100mm long (2 Nos) type B-21 hinges, 200mm long (1 Nos) suitable handles, 250 mm long aluminium Tower bolt (01 No), aluminium snap beading, screws, etc. complete all as specified and as directed.

S&F for 4.80mm thick sheet plain glass ordinary quality and glazing with oil putty/ wooden beads with nails in square n.exe 0.5 Square metre in each pane etc complete all as specified and directed.

Pressed steel frames for doors, made out of 1.25 mm thick MS sheet, with one or more rebates including supply and fixing of necessary fixing lugs, hinges, lock strike plate etc. complete, of frame size 105 mm x 60 mm, including one shop coat of red oxide zinc chrome primer, including bottom of each chowkat to be welded with and including 25 x 3 mm thick flat iron projecting 10 cm on either side and back filling to chowkats with PCC 1:3:6 type C-0 using 12.5 mm graded crushed stone aggregates after applying and including one coat of black paint to prevent from corrosion complete all as specified and as directed by Engr-in-Charge.

M&L 2nd class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the soild, rounded or chamfered, put together with glue pinned at joints, supplied and fixed plain fillets, square, rectangular or triangular in section clean swan, secured with nails or brads complete all as specified and as directed.

Mild Steel Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) as in hold fast, bed block and like complete all as specified and directed by Engr-in-Charge.

Factory made 35mm thick IInd Class Hard wood Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified and directed by Engineer-in-Charge.

40 mm thick flush shutters, solid core construction, with block board core and plywood face pannels and one face is covered with decorative face veneer with 4mm thick teak wood beading all around the edges to match, complete all as specified and directed by Engineer-in charge.

S&F for factory made 35mm thick 2nd class hard wood, Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.20 (a); supplied and fitted to chowkats all as specified and as directed by Engineer-in-Charge.

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165 complete all as specified and as directed

Plain Sheet glass 3.00 mm thick, ordinary quality and glazing with oil pane putty in squares not exceeding 0.5 Sq. mm in each pane, complete, complete all as specified and as directed.

Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and as directed by Engr-in-Charge.

Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples, fixed in repairs complete all as specified and as directed by Engr-in-Charge.

Butt hinges, medium weight, cold rolled mild steel and fixed with screws to wooden frames or with welding to existing MS frames, 100 mm size, ISI marked, complete all as specified and directed by Engineer-in- Charge.

S&F for Aluminum, anodized, barrel tower bolts, ISI Marked, of extruded section 150 mm long, complete all as specified and directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed.

Butt hinges, medium weight, cold rolled stainless steel and fixed with screws to wooden frames or with welding to existing MS frames, 100 mm size, ISI marked, complete all as specified and directed by Engineer-in- Charge.

S&F 75mm long aluminium anodized, butt hinges of extruded section complete all as specified and directed.

S&F for Aluminum, anodized, barrel tower bolts, ISI Marked, of extruded section 100 mm long, complete all as specified and directed.

S&F 100 mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed.

S&F in repair 300mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

S&F 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed, fixed in repairs, complete all as specified and as directed

M&L for pre cast cement concrete block masonary of 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) with soild blocks, exc.10cm in width, set and jointed in cement mortor 1:6 complete all as spd and directed.

M&L for pre cast cement concrete block masonary (except blocks) of 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) with soild blocks, using old concrete blocks obtained from the demolition, exc.10cm in width, set and jointed in cement mortor 1:6 complete all as spd and directed.

M&L for 15mm thick rendering in CM (1:6) on other than fair faces of brick work or stone masonary work, mixed with liquid water proofing admixture @ as per manufacturer's instructions by weight of cement finishing the surfaces with even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick rendering in cement mortar 1:4 on fair faces of brick walls or on concrete surfaces, finished even and smooth without using extra cement in complete all as specified and as directed

Supply only liquid Water Proofing Admixture complete all as specified and directed. Make: Pidilite/Dr Fixit

Rotational moulded polyethylene water storage tank, inner and out white, two layers, ISI marked (cylinderical vertical with closed top) hoisted with threaded cap and fixed in position all as specified in SSR Part-I of Capacity 500 litres each including all accessories (i.e GI nipples, etc), including provn of 20/15mm dia spout for connecting inlet, outlet, overflow and washout pipes, including taking down of old broken water tank complete all as specified and as directed by Engr-in-Charge.

Rotational moulded polyethylene water storage PUF tank, PUF insulated with 75 mm thick PUF insulation of density not less than 48Kg/Cum, inner and out white, two layers, ISI marked (cylinderical vertical/rectangular/loft type with closed top) hoisted with Threaded Cap and fixed in position all as specified in SSR Part-I of Capacity 500 litres each including all accessories (i.e GI nipples, etc), including provn of 20/15mm dia spout for connecting inlet, outlet, overflow and washout pipes, including taking down of old broken water tank complete all as specified and as directed by Engr-in-Charge.

Rotational moulded polyethylene water storage tank, inner and out white, two layers, ISI marked (cylinderical vertical with closed top) hoisted with Threaded Cap and fixed in position all as specified in SSR Part-I of Capacity 1000 litres each including all accessories (i.e GI nipples, etc), including provn of 20/15mm dia spout for connecting inlet, outlet, overflow and washout pipes, including taking down of old broken water tank complete all as specified and as directed by Engr-in-Charge.

Rotational moulded polyethylene water storage PUF tank, PUF insulated with 75 mm thick PUF insulation of density not less than 48Kg/Cum, inner and out white, two layers, ISI marked (cylinderical vertical/rectangular/loft type with closed top) hoisted with Threaded Cap and fixed in position all as specified in SSR Part-I of Capacity 1000 litres each including all accessories (i.e GI nipples, etc), including provn of 20/15mm dia spout for connecting inlet, outlet, overflow and washout pipes, including taking down of old broken water tank complete all as specified and as directed by Engr-in-Charge.

25mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 455 gram), fixed in repairs, complete all as specified and as directed by Engineer-in-Charge.

15mm bore bib tap, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule, fixed in repairs, complete all as specified and directed by Engineer-in-Charge.

15mm bore pillar tap cast copper alloy chromium plated screwed downhigh pressure, with or without lettered 'hot or cold' with long screwed shanks and fly-nuts screwed for iron pipe, fixed in repairs, complete all as specified and directed by Engineer-in-Charge.

Chromium plated, long shank, concealed type, Stop valve/cock, cast copper alloy, screwed down, high pressure with handle, fancy type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, fixed in repairs, complete all as specified.

Angular stop cock/Angle cock with wall flange, fancy type, brass, chromium plated, screwed down for iron pipe or for brass ferrule for bore of pipe 15 mm, fixed in repairs, complete all as specified and as directed by Engr-in-Charge.

S & F 750 mm long, 32mm dia., PVC flexible Waste pipe for sinks / wash hand basins, fixed in repairs, complete all as specified and as directed.

S & F 750 mm long, 40 mm dia., PVC flexible Waste pipe for sinks / wash hand basins, fixed in repairs, complete all as specified and as directed..

Waste coupling of PTMT (half or full threaded), 32mm bore dia of discharge pipe (Minimum weight 32mm-45gms/40mm-60 gms) fixed in repairs, complete all as specified and directed by Engineer-in-Charge.

15mm bore, Pillar tap standard of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-110 gms), fixed in repairs, complete all as specified and as directed by Engineer-in-Charge.

15mm bore, Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-90gms/20mm-125gms), fixed in repairs, complete all as specified and as directed by Engineer-in-Charge.

15mm bore, Stop valve standard of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-90gms/20mm-92gms), fixed in repairs, complete all as specified and as directed by Engineer-in-Charge.

PVC connections 15 mm size with PTMT nuts of length 450 mm, fixed in repairs, complete all as specified and diected by Engr-in-charge.

Viterous china wash basin, white flat back size 550 x 400mm including waste coupling CP 32mm dia and CI brackets of iron 65 x 65 x 6mm embedded in PCC block with PCC 1:2:4 type B-1 and PVC waste pipe 32mm dia & CP grating with holes fixed in repairs complete, all as specified and as directed by Engr-in-Charge.

Vitreous china water closet, 'Orissa' pattern, including lime concrete bedding, size 580 x 440 mm white with integral foot rests excluding flushing cistern and flush pipe but including connection to trap, anti syphonage pipe etc. complete fixed in repairs, incl bedding with PCC 1:2:4 type B-1 using 20 mm grade stone aggregate complete all as specified and as directed by Engr-in-Charge.

Vitreous China wash down water closet pan and seat cover (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including P or S trap and including plastic water closet seat, black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device, including connection to drain pipe (or out going pipe) and to flushing pipe, antisyphonage pipe, etc. including cast iron 'P' or 'S' trap for 100mm bore of pipe, fixed in repairs complete all as specified and as directed by Engr-in-Charge.

10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with twin flush provision, complete, fixed in repairs all as specified and as directed by Engr-in-Charge. MAKE: Cera Model Combiflush twin flush as per Cat Part No. B1020101 (Old Cat Part No 2603) or equivalent in HINDWARE/PARRYWARE

600 mm x 450 mm mirror of thickness 5/5.5mm of slected quality glass, mounted on 6 mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete, fixed in repairs all as specified and as directed by Engr-in-Charge.

Supply and fixing in repairs health faucet manually operated (Hand held) complete set with CP Nipple-01 (100/50mm as required) and CP Tee-01 No connected to existing taps with 8mm dia 1.20 metre long flexible tube and wall hooks complete all as specified and as directed. Make: Cat part No ALD-CHR-573 of Jaquar or equal approved in Kohler

S & F in repair towel rail 600mm long of PTMT fixed with and including chrominium plated brass screws and wooden/plastic cleats (Min Wt 190 Gms).

S & F in repair CP floor gratings 150mm dia all as directed by the Engr-in-Charge

S&F 15mm bore single leaver basin mixer with popup waste system with chrome finish, fixed in repairs, complete all as specified nad as directed. Make: CAT PART No. OPP-CHR-15051BPM of Jaquar or in equivalent in Kohler/CERA

S&F 15mm bore CP wall mixer 3-in-1 system with provision of bath telephonic shower and over head shower with ben pipe, fixed in repairs, complete all as specified nad as directed. Make: CAT PART No. SHFLR5281N of Jaquar or in equivalent in Kohler/CERA

M&L for two coats cement base paint on newly plastered surfaces of wall including preparation of surfaces including curing before and after applying each coat complete all as specified and directed.

M&L for preperation of new concrete /plastered wall surface of any description, applying three coat of white wash complete all as specified and as directed

M&L for preperation of new concrete /plastered wall surface of any description,applying 3mm thick wall care putty and two coat of distemper oil emulsion over a coat of primer complete all as specified and as directed.

Preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Horizon Construction Company

Mehar Enterprises

SHARMA AND SONS CONSTRUCTION CO

R B TRADERS

BETONG BUILDERS