SPL REP TO BLDG NO P-92 (06 OR QTRS) AT OLD DOMLUR MD ACCN UNDER AGE BR-1

Taking down Cement Plaster of any description on Brick Walls, Stone Walls, Concrete Surfaces including Racking out Joints, hacking for Key, scrubbing down with Water, etc. incl removal of debris outside MD land complete all as specifed and directed.

M&L for rendering 5mm thick on fair faces of concrete surface of ceiling/chajjas in CM 1:3, surface finished even and surface without using extra cement complete all as specifed and directed.

M&L for rendering 15 mm thick on fair faces of brick work or stone masonry surfaces of walls in CM 1:6, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick on other than fair faces of stone masonry or brick masonry of external surface of walls in CM 1:4, surface finished even and smooth without using extra cement complete all as specified and directed.

Cutting/chipping the spalling concrete surfaces of columns, beams, facias, slabs, Chajjas & cartilevers etc and trimming, cleaning the surfaces of any thickness and applying epoxy treatment for bonding old demolished concrete surfaces incl application of one coat of notozinc primer to the exposed reinforcement, plastering in CM 1:4 (average thickness 20mm) finishied even and smooth without using extra cement to level the surface etc incl all necessary scafolding where ever required on site complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), and removal of debris outside MD land complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving etc n.exc 15cm thick above or below ground level including terrazzo finish wherever exist complete all as specified and directed.

Demolition of stone slabs of any description or thickness in floors laid bedded and pointed in any mortar etc. incl removal of debris outside MD land complete all as specified and directed.

M&L for 25mm thick Cement concrete 1:2:4, type B0 (12.50mm graded stone aggregate) as in sub-floor, sub bases, levelling course, floors and pavings etc complete all as specified and directed.

S&F non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement or coloured cement to match the shade of tiles over and incl 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

S&F non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in skirting/dado etc. set and jointed in neat cement slurry and pointed in white cement or coloured cement to match the shade of tile over and incl 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L Non skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M & L for coloured Glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 300X 7mm thick to 8mm mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile over and incl rendering 10 mm thick as backing coat in CM 1:4 complete all as specified and directed.

Roughening surfaces of old concrete floors by hacking, picking, sweeping, cleaning and washing down with water to remove dust etc complete all as specified and directed.

M&L for 18-20mm thick Sadherhali stone slab as in flooring, steps, jambs, pillars, window- cills, steps/stairs, cooking platform and like set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of stone slab Rounding the edges of stone slab over and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for 18-20mm thick Sadherhali stone slab for skirting, riser, dado and like jointing in cm (1:3) cluding pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of stone slab over and rendering including 10 mm thick in CM 1:3 complete all as specified and directed.

M&L 20mm thick Granite work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, rounding the edges of granite over including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for Anti termite treatment to the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as per the manufacturer's instruction and as directed by Engr-in-charge.

S&F 300mm MS ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C-1( using 20mm graded crushed stone aggregate) as in plinth protection laid in alternate bays (n.exc. 2 Sqm each) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight, complete all as specified and directed.

Demolition of brick work or PCC solid block or stone/boulder masonry built in cement mortar complete all as specified and directed. .

M&L for Precast cement concrete block masonry with solid blocks, type C1, 1:3:6 (using 20mm graded crushe/d hard granite stone aggregate) exc 10cm in width & setting in C.M 1:6 complete all as specified and directed.

M&L for Precast cement concrete block masonry with solid blocks, type C1, 1:3:6 (20mm graded aggregate) 10cm thick and setting in CM 1:6 complete all as specified and directed.

Taking down chowkats or frames with shutters (with out taking off shutters from the frames) area n. exc 1.50 Sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (with out taking off shutters from the frames) area exc 1.5 Sqm but n. exc 4 Sqm each complete all as specified and directed.

S & F of pressed steel frames for doors of size 125 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete all as specified and directed by Engr-incharge

S & F of pressed steel frames for doors of size 105 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., complete all as specified and directed by Engr-incharge

M&L for PCC 1:2:4, type B-0 (12.50mm graded aggregate) as in filling of chowkats, steel frame and similar work complete all as specified and directed.

S&F Plain, solid, straight 2nd class hard wood chowkats and frames wrought framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

S&F 2nd class hard wood glazed and skeleton shutters, 35mm thick, open rebated & prepared to receive wire gauge (with sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitread beads for securing glass etc, sizes of members of shutters as specified in SSR Pt-I, section 8, clause 8.24- (a), supplied and fitted to chowkats complete all as specified and directed.

S&F 40 mm flush door shutters, solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F Powder coated aluminium sliding window (three way) frame & shutter with glazed shutter and without wiremesh shutter /skeleton section with the following details and as directed by Engr-in-charge :- (i) Aluminium frame section 116x36.50x1.80mm. (ii) Aluminium shutter glazed/skeleton section 50x20x1.50mm thick. (iii) Aluminium grill size 50mmx50mm and 4 to 5mm thick bars complete all as specified. (iv) Fixing arrangements legs in hold fast in walls incl PCC (1:3:6) making goog distributed surfaces complete in originally shape. (v) 4mm thick glass orinary quality and fixed with rubber gasket for with glazed shutter etc. (vi) Stainless steel wire mesh 0.36mm nominal dia avg aperature 1.14mm and fixed with rubber gasket for without glazed shutter etc. (vii) Aluminium disc /bow hanle and locking system complete

S&F Powder coated aluminium Ventilator (partially fixed glazing and Partially louvered glazing) with the following details and as directed by Engr-in-charge :- (i) Aluminium frame section 45x25x1.80mm. (ii) Fixing arrangements legs in hold fast in walls incl PCC (1:3:6) making goog distributed surfaces complete in originally shape. (v) 4mm thick frosted glass orinary quality (partially fixed glazing and Partially louvered glazing) and fixed with rubber gasket for with glazed shutter etc.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Factory Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. Note: stainless steel butt hinges and necessary S.S screws shall be paid separately.

Dismantling of boarding, any description, fixed in any position with nails complete all as specified and directed.

S&F 19mm thick MDF Board both side finished as in wardrobe any No of compartments & Drawers complete all as specified and directed by Engineer-in-Charge.

Supply only stailess steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with aluminium wire staples with wodden beading on wooden shutter or with screws to steel / aluminium shutter complete all as specified and directed.

Cutting holes in stone/brick walls built in cement mortar for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1;2:4 type B1 exceeding half brick but not exceeding one brick all as specified and as directed.

S&F Mild steel work as in band, strap, hold fast, cleat, hook, hinges, base tie for door frame, support or stay for rain water pipe, guard bars etc and other similar items conforming to Fe-410-0 or Fe-310-0 complete all as specified and as directed.

S&F Continuous (piano) hinges, mild steel bright finish or electrogalvanised complete all as specified and directed.

S&F Butt hinges 100mm extruded aluminium alloy with galvanised mil steel hinge pin anodised and firxed type B-21 complete all as specified and directed.

S&F 150mm long aluminium, anodized barrel tower bolts of extruded section complete all as specified and directed.

S&F 125mm long aluminium anodized handles of extruded section complete all as specified and directed.

S&F 150mm long aluminium handles, cast type anodized complete all as specified and directed.

S&F 300mm aluminium alloy, anodized, sliding door bolts with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F Hasp & staple aluminium anodised, safety type, including bolt to hinge plate and fixed with screw 100mm size complete all as specified and directed.

S&F 15mm dia Magic Eye complete all as specified and directed.

S&F in Repair 25mm dia aluminium anodised Powder coated Curtain Rod of approved quality complete all as specified and directed.

S&F in repair decorative type curtain rod brackets suitable for 25 mm dia curtain rods complete all as specified and directed.

Taking up or down steel tubing and connections 15mm bore incl cleaning for re-fixing or removal to store after necessary disconnection complete all as specified and directed.

Taking up or down steel tubing and connections 20mm bore incl cleaning for re-fixing or removal to store after necessary disconnection complete all as specified and directed.

S&F 20m outer dia CPVC Pipe (ISI Marked) SDR 11 & plain CPVC SDR 11 fittings fixed on wall, celing or floors complete all as specified and directed.

S&F 25m outer dia CPVC Pipe (ISI Marked) SDR II & plain CPVC SDR II fittings fixed on wall, celing or floors complete all as specified and directed.

S&F in repairs Stainless Steel (conforming to AISI -304 grade) Kitchen Sink with drainage board of overall size 915mm x 460mm and bowl size 410mm x 330mm x 160mm depth made of 1mm thick stainless steel sheet with CP waste coupling including ball and chain 300mm long with brass cap rubber plug, 32mm bore PVC waste pipe (heavy duty ) 90 cm long, and bedded in cement morter and fixed on CP cantilever brackets, complete all as specified and directed.

S&F in Repair Bib Tap Sink Cock with flange 15 mm bore complete all as specified and directed by the Engineer -in -charge.

S&F in repairs Stainless steel plate rack of size 900mm x 900mm x 250mm including fixed with rawl plug and screws on walls complete all as specified and directed.

S&F in Repair Vitreous China Wash hand basin, white flat back size 550x400 mm including brackets (including Pillar Tap 15 mm bore Chromium plated fancy type with capstan heads, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts & PVC waste pipe) and bedded in cement morter and fixed on CP cantilever brackets all as specified & directed by Engineer-in-charge.

S&F 40mm bore Galvanised steel spout, medium grade complete all as specified and directed.

S&F in Repair Vitreous China Wash down water closet pan pedastel pattern (EWC) white in colour with and incl plastic water seat and cover white closed pattern with flat bottom and cover and MS chromium plated hinging device incl connection to outgoing pipe and flushing pipe complete all as specified & directed by Engineer-in-charge.

S&F in repairs 10 ltr capacity PVC Low level flushing cistern including 32mm dia PVC flush pipe, fixing in position with PVC connection pipe of 15mm x 600mm long etc complete all as specified and directed.

S&F 15mm bore brass CP wall mixer for mixing hot and cold water screwed down with provision of over lead shower and cock for iron pipe and fixed complete all as specified and directed.

S&F in repairs 15mm Bib taps chromium plated fancy type cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for union complete all as specified and directed.

S&F in repairs 2 in 1 CP 15mm Bib taps Quarter turn fancy type with crutch or butterfly handle screwed down, screwed for iron pipe or for union complete all as specified and directed.

S&F in Repair 15mm Bore Stop Valves / Angle Cock Fancy Type Chromium plated cast copper alloy screwed down high pressure with crutch or butterfly handles screwed both ends complete all as specified and directed.

S&F in repairs Brass chromiun plated tubular towel rail, 20mm dia ‘D’ type, 60CM long between flanges complete all as specified and directed.

S&F in repairs Shower rose with brass chromium plated shower rose with or without swivel joints, 125mm size including fixing to steel pipe or union complete all as specified and directed.

S&F as in repair Hand Shower (Health Faucet) 1 Meter Long Flexible Tube & Hook complete all as specified and directed.

S&F in repairs CP Soap dish 150mm, fixed to wall with chromium plated brass screws complete all as specified and directed.

S&F in repairs toilet paper holder chromium plated complete all as specified and directed.

M&L for preparation of New surfaces of wall and applying two coats of distemper oil bound over a coat of Birla Wall care putty 1mm thick complete all as specified and directed.

M&L for preparation of Newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M & L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces of wall complete all as specified.

Complete removal of existing treatment and preparation of surface of wall, washing, rubbing down and stopping of distempered and painted surface, applying a coat of 1mm thick Birla wall care putty for smooth finished surfaces and applying two coat of oil bound distemper complete all as specified and directed.

M&L for preparation of Old decorated surfaces of ceiling and applying two coat of white wash complete all as specified and directed.

M&L for preparation of New Wood or wood based surfaces over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old steel surface over 10cm with or girth and applying two coats of synthetic enamel paint complete all as specified.

M&L for preparation of new steel surface over 10cm with or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for PVC (SWR) floor trap 75mm dia, including jointing with solvent cement etc fixed in repair complete all as specified and directed.

S&F in repair 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with clamps etc complete all as sepcified and directed.

S&F in repair 75mm dia PVC (SWR) pipes single socketed in any length with rubber joints fixed to walls with clamps etc complete all as specified and directed.

S&F PVC (SWR) bends 110mm dia any radius with access door complete all as specified and directed.

S&F PVC (SWR) bends 75 mm dia any radius with access door complete all as specified and directed.

S&F PVC (SWR) junction single, (Single T) 110mm dia equal or unequal with access door complete all as specified and directed.

S&F PVC (SWR) junction single, (Single T) 75mm dia equal or unequal with access door complete all as specified and directed.

S&F PVC (SWR) branch piece, (Single Y) 110mm dia equal or unequal with access door complete all as specified and directed.

S&F PVC (SWR) branch piece, (Single Y) 75mm dia equal or unequal with access door complete all as specified and directed.

S&F PVC (SWR) vent cowl 110mm bore complete all as specified and directed.

S&F PVC (SWR) vent cowl 75mm bore complete all as specified and directed.

S&F in Repair Chromium Plated Steel Grating of 100mm size With or Without Waste Hole complete all as specified and directed.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for roof /chajja padding including removal of debris outside MD land complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 using 12.5mm grades stone aggregate as in Padding over roof / chajjas, kerb, coping etc finished even and smooth without using extra cement complete all as specified and directed.

M&L Rendering 10mm thick on brick work or concrete surface in CM 1:3 surface finished even and smooth surface without using extra cement including WPC (WPC measured and paid seprately).

M&L for Applying oil bound bitumen primer @ 1.50 Kg/Sqm and providing 3 mm thick APP modified water proofing membrane weighing 3.0 kg/sqm reinforced with non woven polyester matt weighing not less than 150 gm /sqm having softening point not less than 140 centigrate, having tensile strength of 650N/sqm and 350 N/sqm in longitudinal and transverse directions respectively of the reinforced tearing strength of 180N by torch application with minimum 10cm side overlap and 15cm end lap, applying a coat of blown grade hot bitumen 85/25 over the membrane @ 1.2 Kg /Sqm top of membrane surface shall then be finished with solar reflective bituminious aluminium paint @ 0.10 Kg/Sqm complete all as directed including taking down existing treatment all as specified and directed by Engr-in-Charge.

Supply only integral water proofing compound complete all as specified and directed.

Demolition of cement concrete (reinforced) other than ground floors, beams stair cases, landings, chajjas and similar suspended work (reinforcement cut as required to facilitate demolition) complete all as specified and directed.

Form work to rough finished flat surface of sides and soffits of suspended slabs such as roof slabs, floor slabs, landings, chajjas and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Form work rough finished flat surface edges of concrete flats, treads, RCC/PCC bands in walls, chajjas, horizontal or sloping ans similar wk exc 10cm but n exc 20cm wide complete all as specified and directed.

M&L for Reinforced cement concrete Type B-1, 1:2:4 (using 20 mm graded stone aggregate) as in slabs supported on walls,chajjas, beams, landings, deck slab and like complete all as specified and directed.

Providing and fixing pre cast reinforced concrete type B-1, 1:2:4 (using 20 mm graded stone aggregate) for man holes cover slab, set in CM 1:4 including necessary form work complete all as specified and directed. Note:- Reinforcement steel shall be measured and paid separatly)

S&F mild steel TMT bars 10 mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for (Columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

TMT bars 6 to 8 mm dia and over for roof slab, cut to length, bent to shape required, including cranking, bending etc and securing with including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S & F Sheet glass shelf assembly consisting of 5.5mm thick shee glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F 140mm long floor door stopper of aluminium alloy body and tongue, anodised , with hard drawn steel spring complete all as specified and directed.

S&F towel ring of PTMT (minimum weight 90 gms) fixed with and including chromium plated brass screws and wooden /plastic cleats washers etc complete all as specified and directed.

S & F glass corner shelf 8mm thick including CP railing radius 250mm complete all as specified and directed.

S&F magnetic catcher with 8mm dia steel ball and brass body and strike plate including letting in and fixed complete all as specified and directed.

S & F 5 feet long pulley operated clothes drying system kit of 4 pipes consisting of aluminium pipes each of outer dia 22mm and inner dia 19.8mm, pulleys made up of derlin with rope guide mounted on channel pair of length 24" (distance between two pipes is adjustable). Locking system to hide rope knot. Channel to be mounted or fixed with self tapping screws provided in kit. Rope will HDPE double core of 4mm dia complete all as specified and directed by Engr-in-charge.

M&L for PCC 1:4:8 type D2 (40mm graded agg) 75mm thick as in sub base of floor, path/pavement etc complete all as specified and directed.

M & L Chequered cement concrete tiles (glosssy) of size 30cm x 30cm x 20 to 25mm thick (with grey cement and pigments) set, jointed and pointed in neat cement slurry in floor,laid over and incl 15mm thick cement screed base in CM 1:4,laid and jointed with grey cement slurry mixed with pigment to match the shade of the tiles incl cutting, rubbing, grinding complete all as specified and directed.

Taking down copper/ aluminium point wiring(light, fan, socket or power) complete, including fittings and fixtures such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions seperately) and making good distrubed surfaces of wall, floors, etc complete.

Point wiring for One light point / ceiling Fan/Exhaust fan point/ Bell point controlled by one 5 Amps switch one way with PVC insulated and unsheathed FRLS cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS-694 1990 drawn in and including PVC rigid non metalic concealed conduit on stone/brick Bldg conforming to IS-9537 with all accessories including fabricated MS terminal boxes fixed flush with wall surface with 3mm thick laminated sheet top cover fixed with brass screw for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed by Engr-in-Charge.

All as per item No 113 here-in-above but for One light point controlled by one 5 Amps switch two way complete all as specified and directed by Engr-in-Charge.

All as per item No 113 here-in-above but for One 3 pin socket point 5 Amp on independent board complete all as specified and directed by Engr-in-Charge.

All as per item No 113 here-in-above but for One 3 pin socket point 5 Amp on same board with other switches complete all as specified and directed by Engr-in-Charge.

All as per item No. 113 here-in-above but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade (ISI marked) including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour complete all as specified and directed by Engr-in-Charge.

Supply and fix Switch piano, flush button single pole, 5 Amps one way complete all as specified and directed by Engr-in-Charge.

Supply and fix Switch piano, flush button single pole, 5 Amps two way complete all as specified and directed by Engr-in-Charge.

Supply and fix Switch sokcet combination flush type 5 Amp 2/3 pin muliti purpose complete all as specified and directed by Engr-in-Charge.

Supply and fix Switch socket combination flush type 6/16 Amps 3/3 pin universal multipurpose complete all as specified and directed by Engr-in-Charge.

Supply and fix Fan regulator electronic, step & socket type 230 volt, suitable for 1200/1400mm sweep ceiling fan complete all as specified and directed by Engr-in-Charge.

Supply and fix Ceiling rose surface bakelite 65x50mm three terminals including supply and fix PVC blocks complete all as specified and directed by Engr-in-Charge.

Supply and fix in repair door bell electronic, multi music type, 230 volt AC complete all as specified and directed by Engr-in-Charge.

Supply and fix bell Push, flush type, 5 Amp, 230 volt AC complete all as specified and directed by Engr-in-Charge.

S&F in replacement LED tube light fitting of 10 watts 6000K , 230 volt, with aluminium extruded channel powder coated with diffuser for glare free light complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge.

S&F in replacement LED tube light fitting of 20 watts 6000K , 230 volt, with aluminium extruded channel powder coated with diffuser for glare free light complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge.

S&F in repair bldg security light light fittings 1x 35 Watt LED street light with New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08 with all accessories and including connection up with twine core twisted flexible copper conductor cable with 1.5 M long suitable size all as specified and directed.

S&F in repair security light bracket made out of 25 mm bore GI Light grade 1.00 M long to required shape as in bracket for steet light fittings fixed with two pair of MS flate iron clamp of size 32mm X 5 mm thickness of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flate iron surface with two coates of synthetic enamel paint over a coat of red oxide primer complete including taking down unserviceable one all as specified and directed.

Supply and fix in repair Sheet metal enclosure (ISI marked) distribution board VTPN, 415 volts, 4 way Vertical type double door type, 200 Amps rated neutral copper bus bar for housing MCB and fixed and tested on completion complete all as specified and directed.

All as per item No 130 here-in before but SPN 8 ways DB complete all as specified and directed by Engr-in-Charge.

Supply and fix MCB single pole 6 to 32 Amps 240 volts, C series, 10 kA rupturing capacity complete all as specified and directed by Engr-in-Charge.

Supply and fix MCB single pole & neutral 32 Amps 240 volts, C series,10 kA rupturing capacity complete all as specified and directed by Engr-in-Charge.

Supply and fix MCCB Tripple pole & neutral 100 Amps 415 volts, C series,16 kA rupturing capacity providing in DB complete all as specified and directed.

Supply and fix in replacement Sub main wiring with 2 runs of 4.0 sqmm, single core, PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in existing non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 4 sqmm single core PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old submain wiring and type of conduit complete all as specified and directed.

Supply and fix in replacement Sub main wiring with 2 runs of 6.0 sqmm, single core, PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in existing non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 6 sqmm single core PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old submain wiring and type of conduit complete all as specified and directed.

M&L for taking down and dismantling of ceiling fan 1200mm/1400mm sweep 230 Volt 50 C/S AC of any make or model by opening the cover, separating down rod, rotor and stator assembly, locating the fault and making the fan fully in serviceable condition with & including replacing the bearing with similar type of exisitng one, worn out screws of the cover, split pin, twin core flexible copper wire of size 23/0.0076, locking nuts & machine screws with spring washer for ceiling fan blades, oiling and greasing etc, finally painting the ceiling fan with one coat of spray painting with white DUCO Paint & lettering & Numbering the same as per existing ,reassembling & testing the fan complete all as directed.

M&L for rewinding of ceiling fan of size 1200mm/1400mm sweep, 230 volt, 50 C/S, AC by removing of burnt winding from stator and rewinding the same with super enamelled copper winding wire of same gauge, same weight & turns including varnishing of winding & reassembling complete all as directed.

Taking down and Refixed any type and size of Exhaust fan in any description after making necessary connections & testing on completion and making good distrubed surfaces of wall, floors, etc complete all as specified and directed.

Rewinding of Exhaust fan with appropriate size of copper enamelled wire including varnishing, heating with proper insulation complete and testing all as specified and directed.

M&L, Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6.0mm thick buried directly in ground (earth pit depth not less than 2.25m deep below the ground level) with top edge of earth plate at a depth not less than 1.5m below ground level connected to earth using GI earth wire of 6mm dia by means of of nuts, bolts and washer and check nuts of GI or steel as shown in electrical plate No.3 of MES SSR-2009 (Part-I) and connected to earth test point all as specified or indicated including testing on completion with and including 15mm bore light grade GI protection pipe 7.5 metre long for earth including PCC (1:2:4) pit with RCC (1:2:4) type B-1 cover, 40mm thick reinforced with 6mm dia MS bars @ 100mm both ways with lifting hooks made out of 6mm dia MS bars, watering arrangement with 20mm dia light grade pipe, funnel, wire mesh, common salt chorcoal, necessary excavation and earth work in any type of soil complete all as specified.

S&F GI tubing medium grade, ISI Marked conforming to IS 1239 Part-I 2004, size of 25 mm bore with and including all fittings such as bends, elbows, tees, short length, socket, union, check nuts, nipples etc. fixed and laid in trenches/floor/under culvert/road crossing etc, including taking down old/rusted complete all as specified and directed

S&F Gun-metal gate valve with iron wheel head, screwed both ends for iron pipe and fixed, ISI marked conforming to IS 778 : 1984, size of 25 mm complete all as specified and directed.

S&F Gun-metal gate valve with iron wheel head, screwed both ends for iron pipe and fixed, ISI marked conforming to IS 778 : 1984, size of 40 mm complete all as specified and directed.

Cutting of existing GI steel tubing and screwing for existing GI steel tubing of size 50/40 mm x 25 mm and connection to existing pipelines complete all as specified and directed.

Supply and laying of cable XLPE Insulated, screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded Size of 35 sqmm x 3.5 core including taking our old burnt/unsv cable complete all as directed by Engr-in-charge.

Excavation in trenches n.exc 1.5 mtr wide and n.exc 1.5 mtr in depth and getting out in soft /loose soil for laying of cable / errection of poles / stay assembly etc complete all as specified and directed.

Returning filling in trenches in soft/loose soil including spreading, leveling, watering and well ramming in layers n .exc 25 cm complete all as specified and directed.

Removing surplus soil to a distance n.exc 50 mtr and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as specified and directed.

Supply and lay common burnt bricks size 230 x 115 x 75 mm,bricks of sub class B,laid at right angle on the cable complete in trenches for cable protection complete all as specified and directed by Engr-in-chagre.

Supply and spreading clean dry river sand in trenches for cushioning of UG cables complete all as specified and directed.

Please Enable Macros to View BoQ information