REPAIR / MAINTENANCE TO CERTAIN B/R ITEM INCL WOODEN / ALUMINIUM JOINERY AND WATER SUPPLY IN OTM/ MD ACCN CHINAR COMPLEX, PB ENCLAVE AND ADJOINING AREA AGE B/R-I OF GE (NORTH) UDHAMPUR.

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frame), area not exc 1.50 Sqm each including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fasts shall be finished identical to match with existing finish without any extra cost to Govt.), complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame), area exc 1.50 Sqm but not exc 4.00 Sqm each including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fasts shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed.

Taking down shutter of any description, area exc 1 Sqm bu nit exc 2.0 Sqm each, complete all as specified and directed.

S&F powder coated (of approved colour) aluminium sections as in frame & shutter of doors/ windows, partitions as in sliding/ openable/ louvers/ fixed type with and including necessary rolling for smooth moving & locking arrangement etc, fixed to wall including preparation making good of disturbed portion both side (internal & external surfaces of wall) to match with existing surface treatment and all sides of aluminium frame shall be sealed with silicon sealent (inner/ outer face), complete all as specified and directed.

S&F anodised aluminium grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC 15) of approved design/ pattern with approved standard section and fixed to the existing window frame with CP brass/ stainless steel screws @ 200mm centre to centre including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening complete all as per site requirement and direction of Engineer-in-Charge.

Demolition of cement concrete (un-reinforced) of any thickness and description and in any position, not otherwise specifically provided for and removal of derbish outside MoD land, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) as in ground floors and pavings exe 15cm thickness (below or above ground level), complete all as specified and directed.

M&L for plain cement concrete 1:5:10 type E-2 (using 40mm graded crushed stone aggregates) as in sunken floor, foundatiom, complete all as specified and directed. Note :- The work will be executed in G+3 bldg and rates for scaffolding, ladder and other means as required shall be deemed to include in the quoted rates.

M&L for 25mm thick plain cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) as in sub base for laying floor finishes including finishing the surfaces even and rough without using extra cement, complete all as specified and directed.

M&L for treatment of sunken floor surfaces with 0.488 Kg/Sqm first layer of slurry of cement mixed with acrylic based polymer modified cementitious composite compound @ 0.253 Kg/Sqm. This layer shall be allowed to be cured for 4 hours and then applying in second layer slurry of cement @ 0.242 Kg/Sqm mixed with acrylic based polymer based modified cementitious composite compound @ 0.126 Kg/Sqm. This layer shall be allowed to be cured for 4 hours including taking down old/existing treatment with wire brusing and clearing the dust and foreign material before new treatment and incuding one GI light grade 450mm long 32mm dia spout to each sunken floor, complete all as specified and directed.

Demolition of cement concrete (unreinforced) as in roofs of existing water proofing treatment of any type and any thickness, complete all as specified and directed.

M&L for applying bituminous primer confiriming to IS-3384 @ 0.40 Kg/Sqm on prepared surface on sunny day. After the primed surface has dried and apply a coat of hot blown 85/25 penetration grade blown bitumen, confirming to IS:702 @ 1.20 Kg/Sqm on the surfaces. Provide APP (Atactiic Polypropylene) modified polymeric five layered membrane with central core of 100micron high molecular high density firm. Minimum weight of membrance will be 3 Kg/Sqm. APP membrance will be laid across the slope from lowest line sloping roof towards ridge with minimum end lap of 150mm & side lap of 75mm bonded with hot blown bitumen. Over the APP membrance apply semi hot blown 85/25 penetration grade bitumen @ 1.20 Kg/Sqm and blinded with fine sand in dry condition @ 0.50 Kg/Sqm dusted over the bitumen coat, complete all as specified and directed. Note :- The laying of the membrane shall be got done by authorized applicator of the membrane manufacturer.

M&L for factory made precast machine pressed tiles in cement concrete 1:2:4, type B-0, size of each tile 300mm x 300mm x 20mm thick with grey cement and no pigment, laid/ fixed over and including 15mm thick bedding layer in cement mortar 1:4 mixed with 5% creosote oil, joined & pointed in cement mortar 1:3, complete all as specified and directed.

M&L for preparation of new or previously untreated surface of any description, exc 10cm width or girth and applying two coats of aluminium paint over a coat of primer, complete all as specified and directed.

Demolition of stone slabs and tiles, laid dry or dry beded or pointed of any description or thickness as in floors, aprons etc, complete all as specified and directed.

M&L for 18-20mm thick granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window cills, cooking platforms and the like, one piece full in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with the shade of granite, laid/ fixed over and including 15mm thick screed bed in CM 1:6, complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, aches, pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles, complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre pulp, insulation etc.) or insulation boards/ slabs/ blankets of any thickness including cover fillets, complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connection including cleaning for re-fixing or removal to store, complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connection including cleaning for re-fixing or removal to store, complete all as specified and directed.

Dismantling water tanks of 1000 ltrs capacity and removing to store, complete all as specified and directed.

Dismantling water tanks of 500 ltrs capacity and removing to store, complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) as in ground floor and paving, not exe 15cm thickness (below or above ground level), complete all as specified and directed.

Demolition of reinfroced cement concrete of any description and in any position, not otherwise specifically provided for, complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls etc. of any description including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads, complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks, old size, straight or curved on plan exc 6 mtr mean radius, built in CM 1:4, complete all as specified and directed.

M&L for 15mm thick rendering in two layers (10+5mm) on fair faces of brick work or concrete surfaces in CM 1:4 with using water proofing compound, finished the surface even and smooth without using extra cement, complete all as specified and directed. Note :- Rates for WPC shall be deemed to include in the quoted rates.

M&L for 10mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces, finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 5mm thick rendering in CM 1:3 on ceiling surface, finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8mm thick (square / rectangular), area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid/ fixed over and including 15mm thick screed bed or bedding layer in CM 1:4, complete all as specified and directed.

M&L for glazed ceramic coloured tiles, size of each tile 450mm x 300mm x 6 to 7mm thick, sharp edged (joint free) as on vertical surfaces such as walls, skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, fixed over and including 10mm thick plaster in CM 1:4, complete all as specified and directed.

M&L for vitrified ceramic tiles 10mm thick (Square) polished, light shade, area of each tile not exc 0.38 Sqm as in floors, skirtings etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid/ fixed over and including 15mm thick screed bed or bedding layer in CM 1:6, complete all as specified and directed.

M&L for 50mm thick PCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) in floors, finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4, type B-0 (using 12.5mm graded crushed stone aggregates)as in floor, base of tiles floor, complete all as specified and directed.

M&L for reinforced cement concrete, 1:1.5:3, type A-1 (using 20mm graded crushed stone aggregates) as in slab supported on walls, beams and columns in floor, roofs, landings, balconies, canopies, shelves and the like, complete all as specified and directed.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, floor and roof slabs and shelves, horizontal or sloping and similar work, exc 5cm but not exc. 10cm wide, complete all as specified and directed.

Use and waste of form work to soffits of suspended slabs such as floor slab, landings and similar work, not exc 200mm thick, in rough finished surfaces of concrete, complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over as in reinforcement for concrete, cut to length, bent to shape required including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

S&F 4mm thick sheet / tinted / transparent glass, ordinary quality and glazing with any type of beading or oil putty in square not exc 0.50 Sqm each pane, complete all as specified and directed.

S&F 4mm thick figured glass, pin head type, any size and in any type of frame and glazing with oil putty or beading in square exc 0.50 Sqm in each panes, complete all as specified and directed.

Checking of joinery (wooden/ steel) iron/ aluminium mongery, pelmet box, door springs etc. requiring carpentry work and carrying out minor repairs such as tightening of screws/ nails, minor adjustment of joinery, door/ windows by means of planer/ chiesling etc. including petty repairs material like screws /nails, plug etc. to make it functional, complete all as specified and directed. Note :- Any other mongeries used in work will be measured and paid separately under relevant item.

Repair to aluminium door or window of any size, shape and description including easing, cutting, drilling, including provn of parts such as rubber gasket, blanket cloth, cleats etc. to make door or window fully functional, complete all as specified and directed. Note :- Any other mongeries used in work will be measured and paid separately under relevant item.

S&F in repair 18mm thick prelaminated medium density fibre (MDF) boards, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws as in cupboards, shelves, kitchen cabinet etc, complete all as specified and directed.

S&F in repairs 12mm thick plywood, grade BWR type BB, fixed to timber frame work with nails etc, complete all as specified and directed.

S&F in replacement drawer side channel of std size and including of roller for moving drawer, mild steel bright finish or electrogalvanised, width of flap 30mm, suitable for modular kitchen, complete all as specified and directed.

S&F in replacement stainless steel multipurpose bracket/ basket in wooden drawer/ partitions for storing rations of various types, made of 4mm dia stainless steel rods, fixed in side partitions etc, suitable for modular kitchen, complete all as specified and directed.

Fixing only existing stainless steel multipurpose brackets/ basket in wooden drawer/ partitions for storing rations of various type, complete all as specified and directed.

S&F in replacement stainless steel zero crank hinges (auto) fancy type (with Euro concealed hinges) fixed to shutters in cupboards of standard size and shape, suitable for modular kitchen, complete all as specified and directed.

S&F factory made solid PVC door frame of size 50mm x 47mm, made out of 5mm wall nut colour PVC sheet reinforced with MS Square tube, complete all as specified and directed.

S&F factory made solid PVC moulded door shutter of wall nut colour, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm thick plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing, complete all as specified and directed.

S&F pressed steel frames, section size of frame 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete as specified and directed.

S&F pressed steel frames, section size of frame 165x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete as specified and directed.

S&F factory made 35mm thick flush shutter, solid core constructions with block board core and plywood face panel, commercial plywood on both sides, complete all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skelton shutter, open rebated and prepare to receive glass, gauge etc. for door edges of framing plain, chamfered rounded fitted with cut and mitred beads for securing glass etc, confirming to Section 8.24 (a) of SSr Part-II, complete all as specified and directed.

S&F 100mm long stainless steel butt hinges, medium weight, complete all as specified and directed.

S&F 150mm long aluminium handle, cast type, anodised, complete all as specified and directed.

S&F 150mm long aluminium, anodised, barrel towel bolts of extruded section, complete all as specified and directed.

S&F 125mm long aluminium, anodised, barrel towel bolts of extruded section, complete all as specified and directed.

S&F 250mm long aluminium alloy sliding door bolt with hasp and staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed.

S&F floor door stoper of 140mm long of aluminium alloy body and tongue, anodised with hard drawn steel spring, complete all as specified and directed.

S&F in replacement 125mm long aluminium anodised hasp and staple with mild steel hinge pin including bolts to hinge plate and fixed with screws, complete all as specified and directed.

S&F in replacement 250mm long aluminium alloy sliding door bolt with hasp and staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed.

S&F in replacement 200mm long aluminium anodised barrel tower bolts of extruded section, complete all as specified and directed.

S&F in replacement mild steel cold rolled butt hinge, medium weight, 100mm long, fixed to pressed steel/ angle iron frames by welding, complete all as specified and directed.

S&F in replacement mild steel cold rolled butt hinge, medium weight, 50mm long, fixed to pressed steel/ angle iron frames by welding, complete all as specified and directed.

S&F in replacement continuous piano hinges, mild steel, bright finish or electro galvanised with width of flap 30mm when open, complete all as specified and directed.

S&F in replacement 40mm dia cup board knobs, brass polished, fixed with nut, screws and washer of mild steel, complete all as specified and directed.

S&F in replacement mild steel powder coated or chromium plated peg sets of six of standard quality, complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

S&F in replacement PVC bathroom mirror cabinets (quality as approved by Engr-in-Charge), size 600mm x 400mm with mirror on front door and with one towel rail for hanging towel of MS chromium plated, fixed with brass screw and wooden gutties, complete all as specified and directed.

S&F in replacement MS helical door spring of 300mm size including roller and roller plate, fixed to wooden with crews or welded to steel frames with welding, complete all as specified and directed.

S&F in replacement 25mm dia fancy type mild steel curtain rods, powder coated with end fittings, knobs/ lattos and fixing brackets of required size (two Nos end brackets and two Nos wall brackets) fixed with wooden gutties and CP screws, complete all as specified and directed.

S&F in replacement 25mm dia fancy type stainless steel curtain rod with end fittings, knobs/ lattos and fixing brackets of required size (two Nos end brackets and two Nos wall brackets) fixed with wooden gutties and CP screws, complete all as specified and directed.

S&F in replacement door closer of aluminium die cast body, hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to1000mm in width and of weight between 61 to 80 KG, complete all as specified and directed.

S&F in repair aluminium door seal with PVC bush of adjustable type (overall width 25mm) of approved Quality, fixed to door shutter, complete all as specified and directed.

S&F in replacement vitreous china wash down water closet (pedestal pattern), suitable for 'P' or 'S' trap, white complete including connection to drain pipe and to flushing pipe antisyphonage pipe etc, complete all as specified and directed.

S&F in replacement plastic water closet seat cover, closet pattern with flat button and cover and including mild steel chromium plated or aluminium hinges device, complete all as specified and directed.

S&F in replacement vitreous china squalting pan, Orissa pattern of size 580mm x 440mm, white with integral foot rests and fixed with cement concrete bedding, complete all as specified and directed.

S&F in replacement PVC low level flushing cistern of 10 ltrs capacity, valveless syphonic action type, white with inlet ball valve, float and handle including brackets, PVC 32mm dia flushing pipe suitable for EWC or Orissa WC etc, complete all as specified and directed.

S&F in replacement vitreous china wash hand basin, flat back of size 550mm x 400mm, white including MS brackets and pedestal pattern including cutting for and pinning end including 32mm dia CP brass waste coupling and PVC waste pipe od suitable size and length, complete all as specified and directed.

S&F 32mm dia waste pipe for WHB / sink, complete all as specified and directed.

S&F in replacement 32mm dia CP brass waste coupling, suitable for WHB, complete all as specified and directed.

S&F in replacement 40mm dia CP brass waste coupling, suitable for Kitchen sink, complete all as specified and directed.

S&F PVC lid with locking arrangements, suitable for PVC water tank of any capacity, complete all as specified and directed.

S&F in replacement ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for 15mm bore iron pipe, complete all as specified and directed.

S&F in replacement ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for 20mm bore iron pipe, complete all as specified and directed.

S&F in replacement brass spindle, suitable for 15mm bore CP taps/ mixers, complete all as specifed and directed.

S&F in replacement 20mm dia brass chromium plated tubular towel rails, 'D' type, 60cm long between flanges, complete all as specified and directed.

S&F in replacement glass shelf assembly, consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets, guard and railing 60cm long, complete all as specified and directed.

S&F in replacement corner glass self (with CP brakets), complete all as specified and directed.

S&F in replacement single lever wall mixer, telephonic type, brass, chromium plated, fancy type with capstan head handles with lettered 'hot' and 'cold', screwed down high pressure including CP brass wall flanges and necessary extension nipples, screwed for 15mm bore iron pipe connection, complete all as specified and directed.

S&F in replacement centre hole mixer for mixing hot & cold water for wash hand basin, cast copper alloy with dual capstan heads, chromium plated, screwed down high pressure, with lettered 'Hot' & 'Cold' with long screwed shanks and fly-nuts, screwed for 15mm bore iron pipe, complete all as specified and directed.

S&F in replacement hand shower (telephonic type), chromium plated with 900mm long 15mm bore chrome finish flexible pipe, complete all as specified and directed.

S&F in replacement shower rose, brass chromium plated, size 100mm x 100mm square with or without swivel joint, with & including CP brass arm and wall flange, fixing to steel pipe or union, complete all as specified and directed.

S&F in replacement angle valve, brass chromium plated, fancy type with capstan head handle, screwed down high pressure including CP brass wall flanges, screwed for 15mm bore iron pipe connection, complete all as specified and directed.

S&F in replacement bib tap, brass chromium plated, fancy type, long nose with capstan head handle, screwed down high pressure including CP brass wall flanges, screwed for 15mm bore iron pipe connection, complete all as specified and directed.

S&F in replacement health faucet, brass, chromium plated with 900mm long 15mm bore chrome finish flexible pipe, complete all as specified and directed.

S&F in replacement jet spray, brass chromium plated, heavy duty including flexible pipe, suitable for 15mm bore water connection, suitable for EWC, complete all as specified and directed.

S&F in replacement PVC flexible connection pipe of 450mm long 15mm dia with brass flange nuts & washers, complete all as specified and directed.

S&F in replacement PVC flexible connection pipe of 600mm long 15mm dia with brass flange nuts & washers, complete all as specified and directed.

S&F in replacement soap dish, brass chromium plated, heavy duty, fixed to wall with plugs with brass cadmium plated screws, complete all as specified and directed.

S&F in replacement CP brass grating of 100mm dia with centre hole, complete all as specified and directed.

S&F in replacement toilet paper holder, brass chromium plated, heavy duty, fixed with brass screws, complete all as specified and directed.

S&F in replacement sink wall mixture, brass, chromium plated, fancy type with capstan head handles, screwed down high pressure with lettered 'hot' and 'cold' including CP brass wall flanges and necessary extension nipples, screwed for 15mm bore pipe connection, complete all as specified and directed.

S&F in replacement sink with drainage board, made of stainless steel 1mm thick kitchen or laboratary with lugs, washers and wastes including 32mm dia CP waste coupling and 32mm dia waste pipe of suitable length and bedding in CM to dwarf wall or including fixing cantiliver brackets and connecting upon to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed.

S&F in replacement pillar tap, cast copper alloy with capstan head handle, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with' long screwed shanks and fly-nuts, screwed for 15mm bore iron pipe, complete all as specified and directed.

S&F in replacement rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) of 1000 litres capacity (Tripple layer) white in colour including water tank cover (internaly/ interlocking arrangment for water tank cover), hoisted and fixed in position including tank nipple inlet & outlet and connecting up pipes, complete all as specified and directed.

S&F in replacement rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) of 500 litres capacity (Tripple layer) white in colour including water tank cover (internaly/ interlocking arrangment for water tank cover), hoisted and fixed in position including tank nipple inlet & outlet and connecting up pipes, complete all as specified and directed.

Cleaning of 1000 ltrs capacity water tank including removing all scale and dirt etc. from tank and from mouths of circulating pipes etc, complete all as specified and directed.

Cleaning of 500 ltrs capacity water tank including removing all scale and dirt etc. from tank and from mouths of circulating pipes etc, complete all as specified and directed.

M&L for 15mm bore GI pipe, medium grade with all fittings & fixtures, fixed to walls and ceiling or laid in floors, complete all as specified and directed.

M&L for 20mm bore GI pipe, medium grade with all fittings & fixtures, fixed to walls and ceiling or laid in floors, complete all as specified and directed.

S&F 16mm dia of CPVC pipes SDR 11 and plain CPVC SDR 11 including all necessary fittings, fixed in wall or trenches, complete all as specified and directed.

S&F 20mm dia of CPVC pipes SDR 11 and plain CPVC SDR 11 including all necessary fittings, fixed in wall or trenches, complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description and in any position, complete all as specified and directed.

M&L for rolled mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, confirming to Fe-410-W (Gde-E-250 Quality 'A'), complete all as specified and directed.

Dismantling of asbestos cement (corrugated or semi corrugated) sheets in roof coverings including ridges, complete all as specified and directed.

S&F in repair 0.50mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of any colour, having tensile strength of 550 Mpa as in roof coverings / cladding to walls, fixed with self tapping screws, complete all as specified and directed.

S&F in repair 0.50mm thick pre-painted glavalume aluminium zinc coating GI based plain steel sheet of any colour, having tensile strength of 550 Mpa as in roof coverings / cladding to walls, fixed with self tapping screws, complete all as specified and directed.

M&L for preparation of old decorated plastered surfaces of walls and applying one coat of white wash, complete all as specified and directed.

M&L for preparation of old decorated plastered surfaces of ceiling and applying one coat of white wash, complete all as specified and directed.

M&L for complete removing existing treatment on walls surfaces by scraping down smoke, soots, moulds, moss & efflorences salts and trading oil & greasy spots and applying two coats of distemper oil emulsion, white or tinted over one coat of 1 to 1.20mm thick wall care putty and a coat of wall primer, complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls by using necessary filling compound of Altek / Birla white putty to obtain smooth and even finish with using sand paper and applying two coats of distemper oil emulsion over a coat of wall primer, complete all as specified and directed.

M&L for preparation of old plastered or un-plastered surface of walls by brooming down or steel wire brushing, scraping down smoke, soots, moulds moss and filling nails marks with wall putty and applying one coat of oil bound distemper, white or tinted, complete all as specified and directed.

M&L for preparation of plastered or un-plastered surface of walls, old decorative and washing down, brooming down or steel wire brushing and applying one coat of cement base paint, complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of cement based paint over a coat of alkali resistant cement base primer, complete all as specified and directed.

M&L for complete removing existing treatment upto 4 storey bldg including scraping, removing all mud, cake with wire brush and gunny bags from old plastered surfaces and preparation of surfaces by using necessary filling compound of Altek / Birla white putty exterior grade to obtain smooth and even finish with using sand paper and applying two coats of first quality exterior grade wheather proofing acrylic emulsion paint as per manufacturer's instructions of any shade and colour over a coat of alkali resistant cement based priming paint, complete all as specified and directed. Note :- Rates for ecessary scaffolding and ladder or other means shall be deemed to include in the quoted rates.

M&L for preparation of old wooden painted surface, not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint, white or tinted, complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

M&L for preparation of old painted steel and iron surfaces, exc 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

S&F in repair powder coated GI frame grid of size 600mm x 600m for false ceiling including non asbestos fibre cement building boards of 4mm thick and size 595mm x 595mm, fixed or laid / inserted to timber/ GI/ aluminium frame work with screws and including butterfly clips, complete all as specified and directed.

S&F in repair hollow PVC wall paneling, consisting of 5-6mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site as per specifications and drawing, complete all as specified and directed.

anil construction co. (BID ID -3291099)

HANS RAJ SHARMA (BID ID -3296887)

KUMAR CONSTRUCTION CO (BID ID -3297197)

VARDHMAN INTERNATIONAL (BID ID -3297020)