GE/CHM-109/2024-2025 SPL REPAIR TO BLDG NO T-2347, P-579, PROVN OF 03 WASHING POINT AND ADDN /ALTN IN BLDG NO P354 UNDER AGE B/R II AT CHANDIMANDIR MIL STN

Amount

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed

Demolition of stone slabs and tiles of any description or thickness in floors laid, bedded and pointed in any mortar complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified & directed by Engineer-in-charge.

Demolition of reinforced cement concrete in roofs, floors, beams, staircases, landing, chajjas and similar suspended work, complete all as specified and directed.

Demolition of brick masonry and built in cement mortar including all quoins arches, pillars complete all as specified & directed

Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness. (Below or above ground level) complete all as specified and directed.

Taking down cement plaster from brick walls or concrete surfaces including raking out joints, hacking out for key, scrubbing down with water complete all as specified and directed and removing rubbish etc. complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings complete all as specified and directed.

Dismantling in fillets, rails, posts, raters, purlins etc under 40sqcm in section complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed

Vitrified ceramic tiles 10mm thick First quality (square / rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over and including 20mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Coloured vitrified ceramic tiles, light shade, 8-10mm thick (square/rectangular) , area of each tiles exc 0.42 sqm but n.exc 1 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

All as per serial item No 12 herein before but on skirting etc over and including 10mm thick rendering in cement mortar 1:4

Non skid, first quality ceramic coloured tiles, 7 to 8 mm thick area or each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over and including 15mm thick rendering in cement mortar 1:4 complete all as specified and directed.

Glazed coloured ceramic tiles in vertical surface 300mm x 450mm x 7mm thick , set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

Coloured non skid porcelain tiles exterior grade 300x300x15mm thick heavy duty (Endura from Johnson or equivalent) as in floor, set and jointed in neat slurry and pointed in coloured cement to match the colour of tiles over and including screed bed or bedding layer of 15mm thick in cement mortar 1:6, complete all as specified and directed

16-18mm thick Granite work (of any type table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in, set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite compelte all as specified and directed.

Rounding of / moulding to edges of stone of any description including rubbing and polishing (Granite finish) complete all as specified and directed.

Solid 12mm thick wood polymer composite louvers wall paneling (size 192mm x 2900mm x 14mm) fixed to walls with necessary clip, screw / adhesive complete all as specified and directed. NOTE : The wall paneling has to be in conformity with the existing wall paneling at site. Bidders ae requestd to visit the site before quoting their bid.

Concrete interlocking paver block, with grey cement and no pigment, design as approved, any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade, and including laid over 25mm thick sand cushioning, complete all as specified and directed

Factory made coloured chequered cement concrete tiles 300mm x 300mm x 22-25mm thick (with grey cement and pigments), set, jointed and pointed in neat cement slurry with grey cement with pigment to match the colour of tiles, glossy finish, laid over and including 20mm thick screed bed in cement mortar 1:6, complete all as specified and directed

Kota Stone Slab flooring, 18-20mm thick (one piece), best quality over and including cement screed bed 15mm thick in cement mortar 1:6, laid and jointed with grey cement slurry and pointed with grey cement mixed with pigment to match the shade of the slab including cutting, rubbing, grinding and polishing (Mirror finish) complete all as specified and directed.

All as per serial item No 22 hereinbefore but on skirting / vertical surfaces laid over and including 10mm screed layer in cement mortar 1:3, cutting, rubbing, grinding and polishing complete, all as specified.

Cement concrete type B-0, 1:2:4 using (12.5 mm graded crushed stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, parapets and railings upto 60 cm in height, copings, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including the use of forms or moulds with plain faces complete all as specified and directed. (Cement concrete item shall be reinforced, where ordered. Reinforcement shall be measured and paid separately).

25mm thick Plain cement concrete 1:2:4 type B-0 using 12.5mm graded aggregate as in sub base complete all as specified & directed.

providing cement concrete type D2, 1:4:8 using 40 mm graded stone aggregate, as in foundation, mass concrete etc., complete all as specified and as directed

75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base etc, finished even and rough complete all as specified and directed.

100mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base etc, finished even and rough complete all as specified and directed.

Powder coated GI Frame work grid (Size of grid 605 x 605mm )comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm, fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre with hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long, complete all as specified and directed

4mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws, complete all as specified.

PVC sheet fillet 35mm wide, 5mm thick for wall paneling, inlusive fixing on to wall to make PVC frame complete all as specified and directed.

Reinforced cement concrete type A-1, 1:1½:3 (nominal mix, using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams etc, shelves and the like complete all as specified and directed (reinforcement shall be measured and paid for separately).

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm complete all as specified and directed.

TMT bars for reinforcement, 6 to 8mm dia & over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed by Engineer-in-Charge.

All as per serial item No 36 herein before but 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders, -ditto-

Precast cement concrete (1:2:4) type B-1 using 20mm graded crushed stone aggregate as in cover slabs set in cement mortar (1:6) complete all as specified and directed.

Brick work with sub class ‘B’ bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:6 complete all as specified & directed.

Brick work with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified & directed.

10mm thick rendering in cement mortar 1:6 on brick walls or concrete surface and finished fair and even without using extra cement complete all as specified & directed.

Rendering 15mm thick plaster in cement mortar 1:4 on brick or concrete surface of wall with mixing of WPC, finished even and fair without using extra cement complete all as specified and directed by Engineer-in-charge. Note :- WPC will be measured & paid separately as supply only).

Material and labour 5mm thick rendering in Cement and Sand mortar 1:3 concrete surfaces as in ceiling / chajjas facia at any position finished even and smooth without using extra cement complete all as specified and directedng

Complete removal of existing treatment on wall and preparation of surfaces, of any description complete all as specified and directed.

Applying Wall care putty (average thickness 1-2mm as required for desired smoothness and leveling of surfaces in two or more layers) and sand papering for making the surfaces even and smooth complete all as specified and directed.

Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper in approved tint over a coat of primer, all as specified and directed.

Preparation of old decorated wall surfaces and applying two coats of oil bound distemper complete all as specified and directed.

Preparation of old decorated wall surfaces and applying one coat of oil bound distemper complete all as specified and directed.

Preparation of new surfacs and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, complete all as specified and directed.

Applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 Square metre over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Square metre over old surfaces, complete all as specified and directed.

Applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 Square metre over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Square metre over old surfaces, including 2mm thick wall care putty on surfaces complete all as specified and directed.

Three coats of white wash on ceiling surfaces including preparation of new plastered surfaces complete all as specified and directed

One coat of white wash on ceiling surfaces including preparation of old plastered surfaces complete all as specified and directed

Preparation of new plastered surfaces of walls and applying two coats of cement base paint including all necessary scaffolding and safety arrangements, complete all as specified and directed.

Material and labour for preparation of new steel surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer complete all as specified & directed by Engineer-in-charge.

Preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Applying one coat of synthetic enameled paint on steel and iron surfaces over 10 cm width or girth including preparation of old surfaces complete all as specified & directed.

Preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparation of old wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Taking down chowkats or frame exc. 1.5 sqm and n exc 4 Sqm with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkats or frame n. exc. 1.5 sqm each with shutters (without taking off shutters from the frame) including grill complete all as specified and directed.

Taking down shutter of any description exc 1 Sqm but n.exc 2 Sqm each complete all as specified and directed.

Taking down and re-fixing of shutters of any description exc 1 sqm but not exc 2 sqm each in same opening after securing or easing & adjusting complete all as specified & directed.

Factory made pressed steel frames of profile width 125mm x 60mm fabricated from 1.25 mm thick sheet, for doors with one or more rebate including necessary fixing lugs, hinges, lock strike plate, etc. & one shop coat of primer, including PCC 1:3:6 complete all as specified and directed.

Factory made pressed steel frames of profile width 105mm x 60mm fabricated from 1.25 mm thick sheet, for doors with one or more rebate including necessary fixing lugs, hinges, lock strike plate, etc. & one shop coat of primer, including PCC 1:3:6 complete all as specified and directed.

Steel window, fixed as in repair box type, primer coated, 1.00mm wall thickness, with glazing bar and openable shutter prepared to recieve sheet glass, complete including cutting holes, four Nos. for each window and making good dismantled portion in PCC (1:2:4) type B-1. including following fittings welded to frame/ shutter:- (a) Hold fast 150mm out of 25x6mm flat iron made to shape- 04 Nos. each window (02Nos. on each side). (b) Handle of 'Z' section 20mmx25mm, 100mm long- 01No. each leaf. (c) MS tower bolt 150mm long- 02 Nos. each leaf. (d) 'Z' section 20mmx25mm, 100mm long stopper 01 No. each leaf. (e) Cleat 55mm long of hollow square section 15mmx15mm of 24 guage wall thickness, welded to hinge of 55mm size 01 No. per leaf. (f) MS box type hinges of 75 mm size- 02Nos. per leaf. (g) Fabrication & fixing complete. Note: Glass panes & painting shall be measured & paid separately under respective item.s. Design shall be approved from Engr-in-Charge as existing at site and all as per Drawing before fabrication and bulk order to the manufacturer.

All as per serial item No 66 hereinbefore but without glazing bar.

Framed work such as grills, gratings, etc with ends of bars shouldered and / or riverted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, raillings and similar work confirming to Fe-290 grade Fe-165 complete all as specified & directed by Engineer-in-charge.

Mild steel framed work as in doors or gates of angles or other sections with gusset plates complete drilled for fixing of steel sheeting or other covering. Doors etc to be prepared for hanging or sliding with including hooks and hinges (excluding of covering steel sheeting) fastening, locking arrangement, etc conforming to Fe-410-O or Fe-310-O all as specified and directed.

Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete all as specified and directed.

Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

5.00mm thick ordinary quality tinted glass, fixed to aluminum frame work in panels exc 0.5 Sqm in each pane, complete all as specified & directed.

3mm thick aluminium composite panel sheet (ACP) of colour as approved by Engr In Charge, all as specified and directed.

Mortice lock, verticle type, mild steel, 4 levers, size 100mm, brass body, complete all as specified and directed

Door closer hydraulically regulated of aluminium extruded section, designation No. 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg, complete all as specified and directed.

Door closer hydraulically regulated of aluminium extruded section, designation No. 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg, fixed as in repair complete all as specified and directed.

Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed.

35mm thick flush shutters, solid core construction, with block board core & plywood face panels, commercial type on both sides all as specified & directed by Engineer-in-charge.

Glazed and gauged skelton shutter (Factory made) 35mm thick of second class hard wood open rebated & prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut & mitred beads for securing glass etc including priming coat. Size of members of shutters as specified in SSR Part I Section 8, clause 8.20 (a) including Kiln seasoned and chemically pressure treated, complete all as specified & directed.

Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed with stainless steel wire staples , complete all as specified and directed.

300mm long mild steel helical door springs including roller and roller plate, as in repair complete all as specified and directed.

200 mm size aluminium , barrel tower bolt of extruded section and fixed complete all as specified and directed.

300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed,complete all as specified and directed.

150 mm aluminium handles cast type anodized complete all as specified and directed.

100 mm aluminium handles cast type anodized complete all as specified and directed.

100 mm size butt hinges medium weight cold rolled mild steel complete, all as specified and directed.

25mm dia stainless steel curtain rod including fixing fancy types brackets, stops, rollers etc., as in repairs complete all as specified and directed.

PVC (SWR) rain water pipe, 75mm bore, single socketed in any length with rubber ring joints, fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm, fixed as in repair including nuts bolts etc, complete all as specified and directed.

PVC (SWR) rain water pipe, 110mm bore, single socketed in any length with rubber ring joints, fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm, fixed as in repair including nuts bolts etc, complete all as specified and directed.

PVC (SWR) rain water pipe, 110mm bore, single socketed in any length with rubber ring joints, fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm, including nuts bolts etc, complete all as specified and directed.

PVC (SWR) pipe, 75mm bore, single socketed in any length with rubber ring joints, laid in floorsor in trenches, complete all as specified and directed.

75 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

110 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

PVC (SWR) junction single, (Single T) equal or unequal 75mm dia complete all as specified and directed.

Bottle trap of PTMT suitable for 32mm (Minimum weight -260gms) having minimum water seal of 25mm complete all as specified and directed.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75mm bore, including jointing to waste pipe set in cement concrete type B-1(1:2:4) , fixed as in repair complete all as specified.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75mm bore, including jointing to waste pipe set in cement concrete type B-1(1:2:4) , complete all as specified.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement 110mm bore, including jointing to waste pipe set in cement concrete type B-1(1:2:4) , complete all as specified.

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, fixed as in repair complete all as specified and directed.

Counter top wash basin, of Size 560x 470x190mm, oval shape, white colour, including waste pipe, CP waste coupling etc fixed in position, fixed as in repair complete all as specified and directed.

Bib tap, fancy type cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for brass ferrule, suitable for 15mm bore pipe, fixed as in repair complete all as specified and directed.

Bib tap, fancy type cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for brass ferrule, suitable for 15mm bore pipe, complete all as specified and directed.

Angular stop cock, fancy type, cast copper alloy chromium plated, screwed down, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 20mm bore pipe, fixed complete all as specified and directed.

Soap dish of cast copper alloy, chromium plated (CP), complete all as specified and directed.

Wash hand Basin brass Mixer of chromium plated hot and cold water screwed down for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repair complete all as specified and directed

15mm dia PVC connection with PTMT nut, of length 450mm, fixed as in repair complete all as specified and directed.

Towel rail 600mm long of stainless steel fixed with and including chromium plated brass screws and wooden / plastic cleatcomplete all as specified and directed.

Taking up or down steel tubing and connections 15mm bore, complete all as specified and directed.

Taking up or down steel tubing and connections 20mm bore, complete all as specified and directed.

15 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors, complete all as specified and directed.

20 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors, complete all as specified and directed.

Male Brass Threaded Adaptor 20mm dia (MTA/ MBTA) ) for CPVC pipe complete all as specified and directed.

Female Brass Threaded Adaptor (FTA/ FBTA) 20mm dia for CPVC pipe complete all as specified and directed.

20mm (outer dia) CPVC pipes, SDR 11 and Plain CPVC SDR 11 fittings, fixed on walls/ceiling or laying in floors, complete all as specified.

Brass elbow 20mm for CPVC pipe complete all as specified and directed.

Brass Tee 20mm dia for CPVC pipe complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings etc and cutting chases for concealed water tubing & making good, cutting not exc 10 cm girth, in brick walls complete all as specified and directed.

Supply only integral water proofing compound (ISI Marked) complete all as specified & directed.

Supply and fix 1000 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) triple layered, screwable lid, hoisted and fixed in position, including tank nipple, PTMT 20mm bore etc, including dismantling of existing water tank complete all as specified

Supply and fix 1000 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) triple layered, screwable lid, hoisted and fixed in position, including tank nipple, PTMT 20mm bore etc, complete all as specified

Supply and fix 500 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) triple layered, screwable lid, hoisted and fixed in position, including tank nipple, PTMT 20mm bore etc, including dismantling of existing water tank complete all as specified

Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

2mm thick fibre glass reinforced translucent plain coloured sheeting with side lap, fixed with coach screws as in roof, wall etc, fixed as in repair complete all as specified and directed.

Steel work in tubular trusses and tubular posts including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 t complete all as specified & directed by Engineer-in-Charge

Rolled sections as in main and cross beams, hip and jack rafters,purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates, conforming to Fe-290 Gde E165, all as specified and directed.

Plain cement mortar 1:3:6 (type C-2 using 40mm graded aggregate), 75mm thick as in Plinth protection , finishing cement concrete even and smooth without using extra cement, all as specified.

Dismantling of existing brick tiles or terracing tiles single layer on roof grouted in cement mortar complete all as specified & directed.

Demolition of mud in roofs, any thickness incl plastering and leeping etc (whether full thickness removed or only a part thereof) complete all as specified & directed.

25mm thick PCC 1:2:4 type B-0 (using 20m graded crushed stone aggregate) as in roof padding, finished fair and even without using extra cement, complete all as specified and directed.

3mm thick Atactic polypropylene polymer (APP) based polymeric membrane minimum weighing 3.6kg/sqm and reinforced with polyester non woven fabric (weight not less than 150 gms/sqm) laid over a coat of oil bound bitumen primer @0.40L/Sqm by same membrane manufacturer of density 0.87 to 0.89 kg/L at 25° C temperature and viscosity 70 to 160 CPS. The membrane shall be laid using butane torch and sealing all joints etc having 75mm side lap joint and 100m end lap joint after preparing the surface as per standard practice and as per manufacturer instructions including dismantling of existing felt /treatment, complete all as specified & directed.

40mm thick brick tiles laid on mud mortar and joints grouted and pointed flush in separate operation in cement mortar 1:3 mixed with crude oil @ 5% by weight of cement on mud phuska complete all as specified and directed.

Taking down, chipping and removing the loose, split, damaged cement concrete, cement mortar surfaces of RCC columns, beams, walls, chajjas etc and exposing the reinforcement, wire brushing and cleaning the exposed steel reinforced bar, apply rust remover over the cleaned re-barsurface wash the re-bar with clean water for removing all rusts fromthe old re-barsurfaces, fixing new reonforcement for strengthen the members as required, applying two coats of epoxy zinc primer on new and old steel surfaces, saturate the substrate with water applying one coat of polymer modified cement and quartz sand mortar in CM 1:3 mix, 40mm average thick in two coats, with and including polymer @10% by weight of cement, including erecting and dismantling steel scafoldingfor carrying out the work upto height of 12 metre (Appx) complete all as specified and as directed.

Excavation in post holes (or similar hole) each in hard/dense soil n.exc 0.50 cu m getting out, returning, filling and ramming earth or broken rubble mixed with earth around, in layers not exc 25 cm, watering and removing surplus spoil at a distance not exc 50 metre and making good surfaces complete all as specified and directed.

Plain cement concrete 1:3:6 type C-1 using 40mm graded crushed stone aggregate as in foundation, for fencing post complete all as specified & directed.

12 mm thick tempered for decorative/crest, , toughened glass, plain/frosted, cut to size, polished edge, homogenious colour fixed as in glass door shutter or glass partition including necessary holes, cutouts & shunk holes and necessary fittings, fixtures, brackets and accessories required like stainless steel hinges, floor door closer, latches, knobs, stop plate etc including ruber beading and silicon clear for joints complete all as specified and directed by Engineer-in-charge. Note : Decoration/design or unit name, emblem, crest over glass shutter will be approved by Engr-in-charge before execution and the rates are inclusive of the same.

200 mm long stainless steel handle, fancy type , fixed to toughened glass, complete all as specified and directed.

Surface excavation not exceeding 30 cms deep and averaging 15cms deep and getting out in any type of soil, complete all as specified.

Sink made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 510mm x 430mm bowl size 430mm x 380mm x 203mm compelte all as specified and directed.

Double bowl sink made of stainless steel 1mm thick kitchen with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 940mm x 460mm x 203mm, bowl size 354mm x 405mm x 203mm compelte all as specified and directed.

32mm dia waste coupling / waste fitting of PTMT (half or full threaded) any colour high-pressure screwed for iron pipe and fixed (minimum weight 45 gms), complete all as specified and directed.

32mm dia Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, complete all as specified and directed.

Plate rack of stainless steel of size 610mmx 760mm x 254mm with steel shelves and hanging arrangements for utensil, complete all as specified and directed.

Taking down carefully aluminum/copper point wiring on & including hard wood battens, surface conduit and board/blocks etc or through conduits for light , socket or power point ,fan point complete incl fitting such as switches ,sockets, ceiling rose , holder socket, light fitting, regulators and making good disturbed surfaces of wall, floor , ceiling etc and removing materials (other than those for which credit has been given by the contractor) to the MES stores yard for keeping in safe custody complete

Point wiring with approved colour code multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade, two run of single core cable for phase & neutral and one run of single core multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade for earth continuity conductor to common earth and connected to earth dolly in existing conduit terminated on and including new modular sunken box and suitable size of frame, cover for mounting switch, socket and regulator fixed on surface flush with wall , comprising of One light /bell/buzzer point controlled by one switch or one fan point controlled by one switch &fan regulator, complete all as specified and directed. Note : (i) Unit rate is inclusive of making good the disturbed surfaces by provding by wall putty/POP after mason work and finshing to match the original surface and nothing extra shall be paid on this account. (ii)Unit rate is inclusive of cutting chases in wall /foor/PCC for sunken box and making good the disturbed surfaces to match the original and nothing extra shall be paid on this account.

All as per serial item 147 herein before but for socket outlet 3 pin 5 Amps on same board complete all as specified and directed

All as per serial item 147 herein before but for socket outlet 3 pin 6 Amps on independent board complete all as specified and directed

All as per serial item 147 herein before but One socket outlet three pin ,6/16 Amp, independent board, with 2.5 Sqmm (nominal area ) FRLSH cable & 2.5 Sqmm (nominal area ) cable as earth continuity conductor

Material and labour for point wiring with approved colour code multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade, two run of single core cable for phase & neutral and one run of single core multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade for earth continuity conductor to common earth and connected to earth dolly in and including new concealed PVC conduit terminated on and including new steel sunken box and suitable size of frame, cover for mounting switch, socket and regulator fixed on surface flush with wall , comprising of One light /bell/buzzer point controlled by one switch or one fan point controlled by one switch &fan regulator, complete all as specified and directed. Note : Unit rate is inclusive of making good the disturbed surfaces by provding by wall putty/POP after mason work and finshing to match the original and nothing extra shall be paid on this account. Note :Unit rate is inclusive of cutting chases in wall /foor/PCC and making good the disturbed surfaces to match the original and nothing extra shall be paid on this account.

All as per serial item 151 herein before but for socket outlet 3 pin 5 Amps on same board complete all as specified and directed

All as per serial item 151 herein before but for socket outlet 3 pin 6 Amps on independent board complete all as specified and directed

All as per serial item 151 herein before but One socket outlet three pin ,6/16 Amp, independent board, with 2.5 Sqmm (nominal area ) FRLSH cable & 2.5 Sqmm (nominal area ) cable as earth continuity conductor

Switch modular type (ISI marked), single pole, one way 6 Amps, one module (ISI marked), complete all as specified & directed.

Switch modular type (ISI marked), single pole, one way 16 Amps, one module (ISI marked), complete all as specified & directed.

Socket shutters outlet 2/3 pin 6 Amp modular type multi purpose two module (ISI marked), complete all as specified & directed.

Socket shutters outlet 2 in 1 pin 6/16 Amp modular type multi purpose combined 2 module (ISI marked), complete all as specified & directed.

Switch piano, flush type, 6 amps, 230 volts, single pole, one way (ISI marked) complete all as directed by Engineer-in-charge

Switch piano, flush type, 16 Amps, 230 volts, single pole, one way (ISI marked) complete all as directed by Engineer-in-charge

Sockets outlet multipurpose 2 in 1 pin, 6 and 6 Amps flush type ISI marked all as specified and directed by Engineer-in-charge

Sockets outlet multipurpose 2 in 1 pin, 6 and 16 Amps flush type ISI marked all as specified and directed by Engineer-in-charge

Modular switch type stepped fan regulator, single pole, 230 volt two module complete all as specified and directed.

Ceiling rose, PVC or polycarbonate of size 65mmx50mm three terminals (ISI marked) all as specified and directed by Engineer-in-charge.

Lamp holder, PVC/Polycarbonate type with back plate modular type fixed on wall suitable for batten fitting ,complete all as specified and directed.

LED lamp 9 watts, B-22 type complete all as specified .

Disconnecting the power supply and taking down carefully by unscrewing from boards fittings and fixtures such as DBs, Junction Box, Panels of any size complete with all MCCB's ,MCB's etc and removing from site, Complete all as specified and directed .

MCCB, 125 Amps, four pole, 3 phase , 16KA, 415 volt with adjustable thermal and maganetic release, with proper thimble complete all as specified and directed

Vertical TPN distribution board double door flush mounting with provisions for MCCBs incomer upto 125 Amps & outgoing 4 way having IP 43 protection Complete all as specified and directed .

Sheet metal enclosure for DB, flush mounted single door suitable for 2 way SPN without busbar 240V completed all as specified and directed.

MCB DB, IP 43 protection, powder coated double door with locking arrangement suitable for surface and flush mounting, 08 way SPN with 200 Amps busbar 240V completed all as specified and directed.

MCB, SPN , 240 volt, 32Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed

MCB, SPN , 240 volt, 40 to 63Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed

MCB ,SP , 240 volt, 6Amps to 32Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed

Sheet metal enclosure with socket plug and MCB Single pole and neutral 20 Amp 220 V with a two pin and earth plug and socket complete with one single pole MCB complete all as specified and directed.

LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size fixed as in repair complete all as specified and directed.

Slim LED lights fitting, 4 feet, 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose fixed as in repair complete all as specified and directed.

Slim LED lights fitting, 2 feet, 1x 10W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose fixed as in repair complete all as specified and directed.

Slim LED lights fitting, 4 feet, 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose fixed as in repair complete all as specified and directed.

Taking down carefully old copper or aluminium sub main wiring of any Nos of wiring and size with earth wire on wooden batten/ surface conduit/ casing- capping complete with its all accessories and making good disturbed surfaces of wall , floors etc complete all as specified and directed.

Sub main wiring with two single core FRLSH PVC insulated and unsheathed cable with copper conductor of size 4 Sqmm (nominal area), 1100 Volt grade(with approved colour coding as per IS) with and including continuous earth wire of size 4 Sqmm PVC insulated and unsheathed FRLSH multi stranded copper conductor 1100 volts grade , and connected to main board drawing through PVC concealed conduit 25mm size(minimum size), cutting chases in walls for PVC concealed conduit and making good the disturbed surfaces by providing by wall putty/POP after mason work and finshing to match the original surfaces and nothing extra shall be paid on this account all as specified and directed. Note : (i) For the purpose of measurement, 2 single core of 4 sqmm and one single core earth cable of 4 sqmm cable shall be considered as 1 running metre. (ii) colour code shall be Red for phase, Black for neutral and green for earth

Sub main wiring with two single core FRLSH PVC insulated and unsheathed cable with copper conductor of size 6 Sqmm (nominal area), 1100 Volt grade(with approved colour coding as per IS) with and including continuous earth wire of size 6 Sqmm PVC insulated and unsheathed FRLSH multi stranded copper conductor 1100 volts grade , and connected to main board drawing through PVC concealed conduit 25mm size(minimum size), cutting chases in walls for PVC concealed conduit and making good the disturbed surfaces by providing by wall putty/POP after mason work and finshing to match the original surfaces and nothing extra shall be paid on this account all as specified and directed. Note : (i) For the purpose of measurement, 2 single core of 6 sqmm and one single core earth cable of 6 sqmm cable shall be considered as 1 running metre. (ii) colour code shall be Red for phase, Black for neutral and green for earth

Supply and fixing sub main wiring with two single core FRLSH PVC insulated and unsheathed cable with copper conductor of size 10 Sqmm (nominal area), 1100 Volt grade(with approved colour coding as per IS) with and including continuous earth wire of size 10 Sqmm PVC insulated and unsheathed FRLSH multi stranded copper conductor 1100 volts grade , and connected to main board drawing through PVC concealed conduit 25mm size(minimum size), cutting chases in walls for PVC concealed conduit and making good the disturbed surfaces by providing by wall putty/POP after mason work and finshing to match the original surfaces and nothing extra shall be paid on this account all as specified and directed. Note : (i) For the purpose of measurement, 2 single core of 10 sqmm and one single core earth cable of 10 sqmm cable shall be considered as 1 running metre. (ii) colour code shall be Red for phase, Black for neutral and green for earth

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10cm girth Complete all as specified and directed .

LED pannel Recess mounted ultra slim 2'x2' - 36 watts edge lit tile in aluminum extruded housing with opal diffuser suitable for perfect lighting complete including cutting hole of required size in POP/false ceiling making good disturbed including taking down any type ceiling fitting, fixed as in repair complee all as specified and directed.

LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver,including lamp bracket upto 1.5metre length as per suitable for fitting including clamp with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection, including taking down old street lght complete all as specified and directed.

LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver,including lamp bracket upto 1.5metre length as per suitable for fitting including clamp with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection, including taking down old street lght complete all as specified and directed.

GI bracket made of GI pipe Medium Grade of size 40mm dia 1.5 mtr length bend to shape of 120 degre fixed o pole/wall with clamp of size 50x6 of suitable length fixed with nuts/ bolts and 1.5 mtere long 1.5 sqmm 2 core flexible wire from connector / ceiling rose to light fitting complete all as specified and directed.

Exhaust fan, steel body AC single Phase. 230V of size 300mm sweep , 1200 rpm, heavy duty with, blades, and frame and louvers complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6.00mm thick, burried directly in ground vertically to a depth not less than 2.25m below normal ground level, with top edge of the plate not less than 1.5m below normal ground level, earth plate surrounded by 15cm thick and packed alternate layers of charcoal dust and common salt, connected with and including earth lead of GI wire 4mm dia (8 SWG) by means of bolts, nuts, check nuts and washers of galvanized iron or thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15mm dia bore including watering pipe 20mm dia bore GI light grade (ISI marked) with funnel and wire mesh, including all necessary excavation and earth work, PCC chamber in plain cement concrete (1:3:6) type C-1 and pit cover of presast RCC with MS frame etc and all as shown in electrical plate No 3 of MES Sch Part-I (2009), complete including dismantling of old earthing, all as specified and directed. Note(s) :- (i) RCC pit cover shall be pre-cast of RCC (1:2:4) type B-1, 80mm thick reinforced with XPM not less than 4Kg/Sqm. (ii) PCC chamber shall be constructed 500 mm away from the edge of earth pit. (iii) Rate shall include earth lead and protection pipe of length 7.5m (iv) Earth resistance should be less than 3Ohm. In case the test results are not found below 3Ohm, complete earthing will be redone without any extra cost to Govt. (v) unit rate including protection pipe and GI wire 4.00mm dia from top to earth plate upto 7.5 meter

Dhingra Brothers (BID ID -3300728)

KUNDRA CONSTRUCTIONS (BID ID -3302237)

Balwantsinghandco (BID ID -3296776)