SPL REPAIR TO MES MD ACCN BLOCK NO P-101 and P-152 16 X OR QTRS

Amount

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

Demolition of cement concrete in ground floor and pavings not exceeding 15 cm thick above or below ground level, complete, all as specified & directed.

Taking down cement plaster on brick or stone walls,ceiling etc. including raking out joints, hacking for key, scrubbing down with water, etc

Taking down chowkats or frames with Shutters ( without taking off the shutter from the frame ) of area n.exc 1.50 Sqm each and removing from site.

All as per description of serial Item No 4 above but area exc 1.50 Sqm but n.exc 4.00 Sqm.

Taking shutter only of any desription of size exc 1 sqm and n.exc 2sqm

All as per item No 6 above but refixing in the same opening.

M&L brick work , with sub class 'B' bricks built in cement mortar 1:6 straight or curved on plan exc 6 mtr mean radius, complete, all as specified & directed.

All as per item No 8 above but except brick work, complete, all as specified & directed.

M&L for 15mm thick cement plastering in cement mortar (1:6) on other than fair faces of brick work or concrete surfaces finished even & smooth without using extra cement, complete, all as specified & directed.

M&L for 15 mm thick cement plastering in cement mortar (1:4) on fair faces of brick work or concrete surfaces with using water proofing compound as per manufacturer's instruction, finished even & smooth without using extra cement, complete, all as specified & directed. Note:- WPC shall be measured & paid for separately.

M&l for 5 mm thick rendering in cement mortar in 1:3 on ceiling surfaces,finished even & smooth without using extra cement, complete, all as specified & directed.

Dismantling timber scantlings framed work in door frame, rails, posts, rafters, purlins, etc. under 40 sq. cm in section complete all as specified.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering to Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening conforming to GdeFe 290 (Gde E-165), complete, all as specified & directed.

S&F 30mm thick flush shutter solid core construction with block board core and decorative face panels veneer with lipping/frame to match on both faces complete all as specified and directed

M&L for 35mm thick IInd class HW glazed /gauged shutters open rebated and prepared to receive glass /gauge etc without sashbars edges of framing plain or chamfered rounded fitted with cut and mitred beads for securing glass/gauge etc all as specified in SSR Part I section 8 clause 8.24 (a), complete, all as specified & directed.

S&F solid PVC door frame of size 50mmX 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing and as directed.

S&F 30mm th factory made PVC door shutter solid panel consisting of frame made out of MS tubes for top & bottom rails .Ms frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC strip of 20mm width stuck inside with solvent cement for stiles and plain colourPVC sheet for top rail , lock rail &bottom rail on either side & as gap insert for top rail & bottom rail . Panelling of plain of plain colur PVC sheet to be fitted in the MS frame welded/sealed to stiles & rails with suitable PVC sheet beading and joined together with solvent cement ,etc all as specified, shown on drawings and directed.

S & F Anodised aluminium window and ventilator shutters,Powder Coating (minimum thickness of powder coating 50 micron) fixed type without sash bar,hook and eye closure Each door having 02 Nos D type handles, 02 Nos aluminium tower bolts 300 mm size,aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete, all as specified & directed.

S & F Anodised aluminium window and ventilator shutters,Powder Coating (minimum thickness of powder coating 50 micron) side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats,hook and eye closure,Each door having 02 Nos D type handles, 02 Nos aluminium tower bolts 300 mm size, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.), complete, all as specified & directed.

S&F anodised aluminium frame powder coated with minimum thickness of powder coating 50 micron for doors, windows, ventilators with one or more rebates including joining cleat for fixing, hinges etc. complete all as specified. complete all as specified and directed. Note:- Prelaminated partical board and sheet glass/wiremesh shall be measured and paid for separately.

M&L for aluminium framed work such as grill, grating etc with end of bars rivetted or screwed with stainless steel and rivetted etc all as specified & directed.

S & F 4.0 mm thick glass sheet ordinary quality glazing fixing in aluminium frame black or transparent in square n.exc 0 .5sqm in each pane all as specified and directed.

S & F 4.0 mm thick glass sheet ordinary quality glazing fixing in aluminium frame black or transparent in square exc 0 .5sqm in each pane all as specified and directed by Engineer-in Charge

S&F 300mm size stainless steel sliding door bolt plate type with bright bolt not less than 12mm dia incl a minimum of six nut and bolts ,four on bolt plate and two on stapple plate complete all as specified & directed.

S&F mild steel barrel tower bolt 200mm size stove enamelled black with bright bolt etc all as specified

S&F 150 mm size mild steel pressed handle oval type

S&F for mild steel butt hinges medium weight 100 mm long, complete, all as specified and directed by Engr-In-Charge.

S&F floor door stopper aluminiumalloy body and tounge 140mm anodised with hard drawn steel spring etc

S&F 300mm size mild steel rat rail rod pattern spring including roller and roller plate complete

S&F in repair block board 19mm th commercial type exterior grade decorated both side fixed to timber frame work around as in kitchen cabinet with magnet catcher and other fixing

S&F in repair pre laminated decorative block board 25mm th prelminated on one face etc fixed to timber frame work

S&F galvanized mild steel wire cloth 0.56mm dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or steel wire staples, complete all as specified and directed.

All as per description of item No 33 above but fixed in repair.

Demolition of stone slabs,floor, hearth or wall tilling incl cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&Lfor Non skid Ceramic coloured, joint free tiles 7 to 8 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.11 sqm and not exceeding 0.18 sqm, as in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15mm thick screed bed in CM 1:6, complete, all as specified and directed by Engr-In-Charge.

M&Lfor Non skid Ceramic coloured, joint free tiles 7 to 8 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.18 sqm and not exceeding 0.38 sqm, as in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15mm thick screed bed in CM 1:6, complete, all as specified and directed by Engr-In-Charge.

M&L for glazed ceramic tiles coloured of size 450 mm x 350 mm x 7mm thick on vertical surfaces such as in skirting, dado etc over and including 10 mm th backing coat in CM 1:4 complete all as specified & directed.

M&L for Granite (of any type) work (table rubbed and polished) 20 mm thick in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over screed or bedding layer in CM 1:4 all as specified and directed .

M&L for Rounding edges of granite stone slabs edge, in steps, cooking plattorm, and other similar situations, complete all as specified and directed .

M&L for PCC 1:4:8 type D-2 using 40 mm graded stone agg as in mass filling and sub base, complete all as specified and directed.

Supply and laying 60mm thick factory made chamfered edge cement concrete interlocking paver block of M-35 grade confirming to IS 15658-2006 with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 25mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete, all as specified & directed.

S&F in repair vitreous china squatting pan ‘Orissa patten’ size 580x440mm white with intergral foot rest (excluding flushing cistern and flush pipe) with "P' or "S" trap including water connection to trap and flushing pipe, flushing cistern etc incl lime concrete bedding and PCC 1:2:4 for making good the floor, complete, all as specified & directed.

S & F in repair PVC 10 ltrs syphonic action type flushing cistern, low level with inlet, ball valve, float and handle including brackets, flush pipe of PVC 32mm bore, connection to WC pan & PVC connection 15mm size with PTMT nuts of length 300mm, complete, all as specified & directed.

Supply and fix for vitreous china ware wash hand basin with pedestal type (color as specified and directed), flat back size 550 X 400mm CP waste coupling, waste fittings, union and waste pipe 32mm dia or required length and all necessary inlet, out let connections complete all as specified and directed

S&F pillar taps, 15mm bore cast copper alloy, with capstan heads, chromimum plated, screwed down hight pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly -nuts, screwed for iron pipe and fixed etc all as specified.

S&F in replacement 20 mm dia harrison rails mild steel with decorative finish , with fixing brackets , stops, rollers complete all as specified and as directed (two brackets per 1.5 M length and 08 Nos roller per 1.RM), complete, all as specified & directed.

Dismantling brick tile or terracing tile single layer on roof, complete all as specified and directed.

Demolition of mud in roofs ,any thickness incl plastering and leeping (weather full thickness removed or part there of), complete all as specified and directed.

Demolition of concrete of any description and in any position not otherwise specifically provided complete all as specified and directed.

M&L for PCC 1:5:10 type E2 with using 40 mm graded stone aggrgate as in filling for sunken floor and like works, complete all as specified and directed.

Supply only Integral waterproofing compound, ISI marked.

M&L for Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces, complete all as specified and directed.

M&L for APP modified polymeric waterproofing membrane not less than 3mm thick, weighing not less than 3.0 Kg/Sqm, reinforced with with polyster non woven fabric (weighing not less than 150 Gm/Sqm) . It shall be laid on primed surface by torch application with side overlap of 75mm and end lap of 100mm . All overlap and joints shall also be sealed by torch application. For parapets, membrane shall be taken to a height of min 60cm and then inserted inside the parapet in a groove. The same shall be finished by a membrane flashing, complete all as per manufacture instructions and as directed by Engr-In-Charge.

M&L for 40 mm average consolidated thickness PCC 1:2:4 type B1 with using 20mm graded stone aggregate as in padding on flat roofs etc, complete, all as specified and directed.

M&L for 40mm thick brick tiles laid on mud mortar and joints grouted flush in cement mortar (1:3), mixed with 5% of crude oil by weight of cement and pointed flush in CM 1:3, complete, all as specified and directed.

All as per description of serial item No. 57 above but except tiles.

M&L for Providing, cement concrete type B-0 1:2:4 (12.5 mm graded aggregate ), as in roof kerbs or mud stops, rounded or chamfered on edges parapets copings, bed plates, etc, complete, all as specified and directed.

Cutting grooves of size 75mm wide and 65mm deep in brick parapet wall for inserting APP membrane and making good the disturbed portion in CM (1:3) etc, complete, all as specified and directed.

M&L for water proofing treatment to sunken floors of kitchen, toilets, laboratories, bath and WC's etc by applying:-(i) Application of two component acrylic modified cementitious coating (aa) The surfaces to be appiled shall be completely dry and free from containments such as dirt , dust ,oil surface treatments and old coatings . Concrete substrates must be mechanically prepared using abrasive blast cleaning or miling to remove cement laitance existing coatings and achive a griping profile that is clean dry and free from laitance and any other from of surfactue contamination. The installation instructions and manufacturer's published literature should be strictly complied with includngf but not limited to the following:- (bb) Chipping out any visible cracks in V-Groove pattern as applicable . Special attention on this part. Cleaning of cracks and then filling those cracks with SIKA latex SBR 100 PUTTY/Dr fixit 302 SBR latex/perma Laxtex SBR /FOSROC Nitabond SBR laxtex / Asian paints latex as required Final clening of surface with power girnder Wire brush & vacuum pressure if required . (cc) Dampen all surfaces immediately ahead of applIcation of Acrylic modified Cementitious coating of SIKA Top seal -107 / Brush bond FOSROC/DR Fixit/STP/CICO.(dd)Whilist the surface is still damo from saturation (S.S.D.) apply one coat of Acrylic modified cementition coating of SIKA Top Seal-107/brush bond FOSROC/DR Fixit/STP/CICO of viscosity as per manufacturer's.instruction. (ee) Apply glass fabric sheet of Sika Fab 1/FOSROC/Dr Fixit/STP whilst the first coat is wet.

(ff) Once touch dry apply second coat of Acrylic modified cementitious coating of SIKA Top seal-107/Brush bond FOSROC/DR Fixit/STP/CICO of viscosity as per manufactureer's instructions on the entire area. (gg) Second coat shall be applied 6-8 hours of application of previous coat and in the direction right angle to the previous coat. (hh) The waterproofing coating should be taken to a height min. 300 mm above the finished floor level on the vertical surface. (jj) It is essential to cure Acrylic modified Cementitious coating immediately after application (min. 6-8 hours drying) for a min. of 3 to 5 days to ensure full cement hydration and to minimize cracking. (kk) A protection layer (12-15mm thick) in CM1;3 admixed with appropriate integral water proofing compound has to be applied on the walls.Admixture : SIKA Plastocrete Plus/FOROC/Dr Fixit/ STP/CICO confirming to IS 2645.Providing and applying a protection screed of 50 mm thick 1:4 cement sand mortar admixed with sika plastocrtete over the applied water proofing coating on horizontal surfaces. Admixture : SIKA Plastocrete Plus/FOROC/Dr Fixit/ STP/CICO confirming to IS 2645.

(ll) All the corners and joints should be pretreated with elastic water proofing sealing tape with a woven bonding mesh on each surface and an elastic expansions zone in the centre of make Sika Seal Tape S/FOSROC/Dr fixit/STP.

(mm) The membrane has to be protected in accordance with the manufacturer's recommendadtions until placement of concrete.The membrane to be inspected for damage just prior to concrete placement and make repairs in accordance with manufacturer's recommendations.

(nn) Water proofing treatment has to be carried out through applicators authorised.

(ii) All the joints of pipes and traps within sunken portion shall be sealed properly by epoxy sealent.

(iii) All CI traps in sunken slabs to be enclosed with PCC 1:1.5:3 (min15 cm) all-round.

(iv) The sunken portion shall be filled with PCC 1:5:10 type E-2 (using 40 mm stone aggregate) complete all as specified (The same shall be measured under item 52 here-in-before).

(v) Providing drainage spout pipe GI 40 mm dia bore light grade up to out side of outer wall( approx 450mm to 600 mm long) including cutting to existing wall and making good the disturbed surface complete all as specified and directed.

(vi) Providing 25 mm th cement concrete 1:2:4 type B-0 using 12.5 mm grade stone aggregate as in flooring for laying floor finish all as specified & directed.

M&L for 25 mm thick cement concrete flooring type B-1, 1:2:4 using 20 mm graded stone aggregate finishing cement concrete surface even and smooth without using extra cement, complete, all as specified and directed.

Dismantling water tanks of any description exc 250 and n.exc 500 ltr capacity

S&F Rotational moulded polythene water storage tanks trible layer (cylinder each vertical with closed top) of capacity 500 Itrs, hoisted and fixed in position including pvc float valve 20mm size,specified in SSR Pt-1

Taking up/ down GI tubing and connections with all fittings 15 mm bore.

All as per description of serial item No. 65 above but 20mm bore.

S&F 15 mmdia GI tubing and connections fixed to wall or ceiling, laid in floor etc

All as per description of serial item No. 67 above but fixing only.

S&F 20 mmdia GI tubing and connections fixed to wall or ceiling, laid in floor etc

All as per description of serial item No. 69 above but fixing only.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed etc. and making good, cutting n. exceeding 20cm girth, complete, all as specified and directed.

S&F in repairs brass CP kitchen sink mixer for mixing Hot and Cold water 15 mm bore screwed down for iron pipe and complete all as specified.

S&F in repair CP shower rose 15mm size fixed to iron pipe

S&F in repairs PVC connection 15mm size with PTMT nuts of length 450mm.

S&F in repair 15mm CP Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S&F in repair 15mm size brass stop valves with crutch or butterfly handles high pressure screwed both ends for iron pipe.

All as per item No76 above but fancy type, chromium plated with long shank and cup (concealed type)

S&F in repair 20mm size stop valves PTMT high pressure screwed for iron pipe .

S & F aluminium anodised tubular towel rail 20mm dia “D” type 60 cm long between flanges incldg brackets complete all as specified and directed. .

Dismantling wrought iron or mild steel work of any description not otherwise provided for

M&L for preparing new surfaces of walls and applying two coats of oil bound distemper over a coat of alkali primer, complete, all as specified & directed.

M&L for Complete removal of existing treatment of walls and applying a coat of oil bound distemper on plastered surface to prepare the surface even and smooth, complete, all as specified & directed.

M&L for Complete removal of existing treatment of walls to prepare the surface even and smooth complete all as specified and directed.

M&L for Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) with colour scheme change complete all as specified and directed .

M&L for three coats of white wash on ceiling on newly plastered surfaces including preparation of surface,complete, all as specified & directed.

M&L for preparation of old treated ceiling surface and applying two coat of white wash , complete, all as specified & directed.

M&L for preparation of new wooden surfaces of any description, over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete, all as specified and directed by Engineer-in-Charge.

M&L for preparation of old or previously treated wooden surfaces of any description, over 10cm in width or girth and applying one coat of synthetic enamel paint complete, all as specified and directed by Engineer-in-Charge.

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide or zinc chrome primer complete, all as specified and directed by Engineer-in-Charge.

M&L for preparation of old or previously treated steel surfaces of any description, over 10cm in width or girth and applying one coat of synthetic enamel paint complete, all as specified and directed by Engineer-in-Charge.

M&L for 25mm thick PCC 1:2:4, type B-0 using 12.5 mm graded stone agg as in levelling course,complete, all as specified and directed .

M&L for 75 mm th PCC 1:3:6 type C2 as in plinth protection with using 40mm graded stone aggregate etc all as specified. Note: Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in altranative bays not exceeding 3m in length. Joints of 6 mm wide 10 mm deep shall be provided along the wall and bays and same shall be filled with between mastic (1:3)

S&F in repair 110 mm bore PVC (SWR) pipes of pressure rating 6kg/per sqcm, single socketed, in any length with rubber ring joints, fixed to walls, complete, all as specified and as directed.

S&F 110 mm bore PVC (SWR) pipes of pressure rating 6kg/per sqcm single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete, all as specified and as directed.

S&F in repair 75 mm bore PVC (SWR) pipes of pressure rating 6kg/per sqcm, single socketed, in any length with rubber ring joints, fixed to walls, complete, all as specified and as directed.

S&F 75 mm bore PVC (SWR) pipes of pressure rating 6kg/per sqcm single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete, all as specified and as directed.

S&F in repair 75mm size PVC (SWR) floor trap plain with grating incl to jointing with waste pipe with adhessive etc all as specified

S&F 110 mm bore PVC (SWR) bends, any radius with oval access door, complete, all as specified and directed by Engineer-in-Charge

S&F 75 mm bore PVC (SWR) bends, any radius with oval access door, complete, all as specified and directed by Engineer-in-Charge.

S&f 100 mm dia stack clamp made out of 25x4mm Flat iron etc all as specified and directed.

S&f 75mm dia stack clamp made out of 25x4mm Flat iron etc all as specified and directed.

M&L for 50mm th PCC 1:2:4 type B1 using 20mm graded stone agreegates as in flooring including finishing the surface even and smooth without using extra cement etc, complete, all as specified & directed.

Taking down carefully surface aluminium or copper point wiring on TW Batten/in conduit/ with PVC casing-caping/conduit (light, fan, socket, or power) complete and making good the disturbed surface of wall/celling etc including taking down fitting such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc and removing material from site and taking credit as per schedule of credit complete all as specified & directed.

M & L for concealed Point wiring complete with 1.5 Sqmm (nominal area) 1100 volts grade single core PVC insulated FR-LSH multistranded copper conductor cable in and including medium grade PVC conduit not less than 20 mm (wall thickness 1.5 mm ) including fitting & accessories, with sunken galvanized pressed steel terminal boxes with 3 mm thick laminated baklite (Hylum/Anchor) sheet top cover for mounting switch, socket etc for one light/fan/bell point controled by one switch and (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm. stranded copper conductor with green FRLSH PVC insulating earth connected to common earth dolly, complete all as specified & directed.

All as per description of serial item No.104 above but for one socket outlet 6 amp controlled by one switch on the same board with other switches

All as per description of serial item No.104 above but for one socket outlet 6 amp controlled by one switch on indepdendent board

All as per serial Item No. 104 here-in-before but for one light point controlled by two numbers, 2 way switches.

M & L for Point wiring with 1100 volts grade single core PVC insulated FRLSH multistranded copper conductor cable 2.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 2.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal box of thickness not less than 1.2 mm covered with 3 mm thick phenolic laminated white sheet cover for one 16 Amp socket outlet controlled by one switch on independent board complete.

S & F switch piano flush button single pole one way 5/6 Amp complete.

S & F switch piano flush button single pole one way 16 Amp complete.

S & F of switch piano, flush type, 5 Amps, 230 volts, single pole, two way, complete all as specified

S & F socket outlet 2 in 1, 2 & 3 pin, 6 Amp, flush type complete.

S & F socket outlet 2 in 1, 3 pin 16 Amp flush type complete.

M & L of lamp holder, PVC/ polycarbonate type complete all as specified

S&F LED lights fitting 1 x 20 W, 220 V AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complect as specified.

S&F LED lights fitting mirror type with high output diffuser 2 feet, 10Watt 220 V AC decorative type with driver holder and LED lAmp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified

S & F ceiling rose 65x50mm 3 terminals polycarbonate body complete.

Supply and fixing fan regulator electronic step type and making connection complete all as specified and as directed.

S & F MCB DB SPN 8 way double door IP 43 complete prewired including Bus Bar with earth bar and neutral bar etc suitable for operation on 240 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed .

Supply and fixing sheet steel metal enclosure (DB) triple pole and neutral 4 way Double Door 415 V, with 200 Amps rated bus bar complete all as specified and directed.

Supply and fixing MCB's single pole and neutral 32 Amps, 240 Volts,10 KA rupturing capacity 'B' curve.complete all as specified & directed.

Supply and fixing MCB's single pole 6 Amps to 32 Amps, 240 Volts,10 KA rupturing capacity 'B' curve.complete all as specified & directed.

Supply and fixing 415 V , 10 KA 'C' curve miniature circuit breaker (MCB's) of capacity 63 Amps TPN. complete all as specified & directed.

S&F in repair of bell AC single pole Ding Dong type 230 volt all as specified.

S&F of bell push flush type 5 Amps complete all as specified.

S & F LED light fitting 1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified.

M & L for submain wiring with approved colour code/as per IS (Red,black & green for single phase) concealed conduit circuit with two single core PVC insulated cable with multistranded copper conductor of nominal cross sectional area of 6.00 Sqmm (FRLS) in and including PVC rigid non metallic medium grade conduit including one run of PVC insulated multistranded copper conductor nominal cross sectinal area of 6.00 Sqmm (FRLS) of continous earth wire green in colour complete all as specified and directed by Engr-In-Charge.(Note :- Two runs of 6.00 Sqmm cable & one run of 6.00 Sqmm earth cable alongwith conduit shall be paid as one unit length)

M& L for painting of ceiling fan complete in situ with synthetic enamel paint by spraying including filling cavity with filler one coat after cleaning all dust etc compete all as specified and directed .

Supply & fix exhaust fan, steel body AC single phase. 230V,50 Hz,1350rpm of size 300 mm sweep with, blades, and frame andlouvers all as specified.

Supply & fix exhaust fan, made of sturdy Engineering plastic complete with louvers shutter voltage 230V 50 HZ 1200 RPM copper winding of size 250 mm sweep with, frame all as specified.

Supply and fix electric water heater, storage type steel body with stainless steel inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 star rated complete with all accessories such as safety valve, thermostat, NRV, connection pipes 2 Nos (stainless steel) etc.all as per directed.

M&L for Earthing complete with galvanised steel earth plate electrode 60x60cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate no. 3 connected to earthing test point all as specified or indicated including testing on complection., earth plate surrounded by packed layers of charcoal dust and common salt 15cm thick, all around including top and bottom and watering pipe 20mm bore of GI pipe light grade with funnel and wire mesh, PCC chamber of size 300x300x300mm (top of chamber minimum 15 cm above the normal ground level (1:3:6) using 20mm graded stone aggregate and RCC cover (1:2:4) type B-I using 20mm graded crushed stone aggregate with 1 nos MS handles of 8mm dia including necessary excavation/ earth work in any type of soil/rock and as shown in Electrical plate No. 3 of SSR Part-I (2020) testing on completion complete all as specified.

M&L for cuttings of holes in PCC or through bricks walls 250 to 300 mm dia for opening for exhaust fan, making good in cement mortar 1:3 or cement concrete 1:2:4 type B2 as required and making good the disturbed portion, complete, all as specified and directed.

S&F LED street light fitting 35 Watt 230 V AC outdoor type with high high pressure die cast aluminium hosing and heat resistant toughened glass complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection complete.

S&F single pole and neutral enclosure with a two pin and earth plug and socket complete with single MCB 20 Amp 240 V for geyser all as specified.

Supply , laying and testing cable XLPE insulated ,PVC sheathed ,PVC bedded ,galvanized steel strip or wire armoured electric power cables (heavy duty) 1100 Volts grade with stranded aluminium condutor of size 25 sq mm 4 core including taking down the old cable complete all as specified and directed .

Excavation in trenches in Soft/disntegrated soil not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, laying of GI pipe etc or soil for shaft, walls, cesspts, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in Soft/loose of soil complete all as specified & directed.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick soft/loose soil, all as specified & directed.

Removing excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point soft /loose soil all as directed .

M&L for sand cushioning with 8 cm sand beneath the cable and 15 cm above the under ground cable below the sand and gently punning the sand above the cable upto10 cm to cushioning to cable complete all as directed by Enginner-in-charge . (Note : The payment will be made for the 18 cm )

Supply and laying common burnt clay building brick Sub class B designation 75 and laying it perpendicular along the length of the cable all as specified and directed.

supply, laying or fixing in repairs 40 mm bore GI tubing "light grade " in treches or on pole for protection of cables complete all as specified & directed.

M/s Dinesh Kumar (BID ID -3359278)

R G ENTERPRISES (BID ID -3359305)