Civil Works

Dismantling the damaged floor finish and dadooing walls in cement mortar with mosaic tiles/Glazed tiles/cuddapah slab and clearing away with carefully stacking the material useful for reuse for any thickness etc., complete complying with standard specification and as directed by the Departmental officers.

Earth work excavation for foundation by manual means for Isolated, Combined and Other type foundations in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2.00mts. and clearing and levelling the site, etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation, basement, etc with filling Crushed Stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing etc. complete complying with standard specification and as directed by the departmental officers - Mixing by mechanical means

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

Reinforced Cement Concrete 1:1-1/2:3 (One Cement, One and a half crushed stone sand and Three hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including Super Plasticiser, laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with Cement Mortar 1:3 (One Cement and Three Sand) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers - manual mix

Foundation and Basement

Ground floor

First Floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel reinforcement grills of all variety like HYSD/CTD/TMTand all grade like Fe 500, Fe550D, Fe 500 D etc., for all RCC works as per design given including cost of steel reinforcement and G.I. binding wire, wastage etc. complete complying with standard specification and as directed by the departmental officers.(Contractor has to make his own arrangements for the supply of steel reinforcement and binding wire)

Brick work in following Cement Mortar using best quality Burnt Clay Brick of size 9" x 4 3/8" x 2 3/4" with class designation of 7.5 conforming to IS 1077-1992 for foundation and basement including Cost of Mortar Plasticizer curing, etc.,complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally.other type of bond shall be done as directed by the Executive Engineer in charge.

For foundation & basement

In Ground floor

In First floor

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc. complete complying with standard specification and as directed by the departmental officers.

Finishing the top of roof with one course of machine Mangalore tiles of following size of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers.

Clean Surface thoroughly with water and remove any loose plaster, flacks, fungus growth etc, from the toilet floor slab and toilet sunken portion by suitable mechanical means like scrapping or wire brushing and wash with adequate water to get an absolutely cleaned surface to take on further treatment.Gal-Tech Multiproof-AD SB modified polymer with cement and fine sand mix ratio 1:2:4 is used to full the grooves, pores, wall to floor joints and surface crakes. Over that Gal-Tech C.T. Epoxy virgin Solvent Free Anticorrosive two packs Resin and Hardener 1:1 mix ratio. The resin and hardener should be mixed thoroughly using a hand held mixer either mechanically or manually. The prepared mixer is then applied as a base coat with uniform application on to the surface it is then impregnated with GalTech GC-110F, impregnation process is done using one coat of Gal-Tech C.T. Epoxy. After touch dry condition is achieved one more coat of Gal-Tech C.T. Epoxy is given uniformly it is again impregnated with Gal-Tech GC-110F over that two coats of Gal-Tech C.T. Epoxy is given as a final finish. Joint less lining system is achieved and now sand is sprinkled on to the finished surface uniformly to get a rough profile to take on further civil works. This system is self-cure after 48 hours civil works can be commenced. This is a solvent free high strength double reinforced system.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

In Ground floor

In First floor

In Second floor

Brick partition walls of 11.50cm thickness using best quality Fly ash Brick of size 230x110x75mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 in Cement Mortar 1:3 (One Cement and Three CS Sand) using hoop iron reinforcement if found necessary including Cost of Mortar Plasticizer, curing etc. complete complying with standard specification and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Ground floor

First Floor

Polishing the old marble flooring with electric polisher machine to high degree more then four times using variety of rough stones such as size 80, 200 and 360 with mixing of marble powder polishing machine more then four times up to final polishing with perfectly smooth and glossy appearance etc, finally the flooring to be washing with thin oxide and oxalic acid with mixed with water etc, complete. The rate is cost of materials, hire charges for polishing machine, labour charges etc, complete, complying with standard specification and as directed by the departmental officers etc., complete.

Dadooing walls with following best approved quality, Designed colour ceramic tiles of size 1200 x 600 x 8mm set in Cement Mortar 1:2 (One Cement and Two sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Paving the floor with best quality Vitrified Tiles of size stainfree nano polish 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Supplying and fixing Korean-type table-top wash basin unit with rear-side vanity mirror, the entire unit made of solid surface (Korean top) material, with smooth, seamless finish, comprising an integrated wash basin, provision for single tap hole (or without tap hole as required), overflow arrangement, waste coupling, and CP fittings, complete with all necessary accessories. The item also includes providing and fixing a rear-side vanity mirror mounted on 12 mm thick charcoal panel, of approved size and thickness, fixed using suitable adhesive and approved fixing accessories. The work includes fixing the wash basin unit in position using approved adhesive and sealant, connecting water supply and waste lines, and testing and commissioning, complete in all respects, as directed by the dept officer. The rate shall be inclusive of the cost of all materials, labour charges, transportation,

Supplying and fabricating the WPC (Wood Plastic Composite) door design printed shutters of 30mm thick with frame scantling size of 3'' x 2'' and both side affixed with 1mm thick special design prelaminated sheet with both side pasted with synthetic resin (or) equvalent to fevicol, such as necessary furniture fittings of 100mm S.S Hinges - 3no's, 150mm S.S Tower bolt - 1no, 150mm S.S Handle - 1no including labour charges for making door with materials neat finishing hire charges for tools and plants etc., complete complying with standard specification and as directed by the departmental officer's.

Labour charges for Core Cutting the RCC item of works for various diameter in all floors and filling the gap after laying the pipe line without any leakage etc., complete as per standard specification and as directed by the departmental officers.

Supplying and fixing in position Two in one wall mixture tap FUS 29273 (Heavy type)/ Roco makeTwo in one tap of approved make conforming to IS spn. And quality including cost of shellac, thread, cutting and threading wherever necessary etc., complete.

Supplying and fixing in position of best approved superior quality ceramic floor mounted european western closet commode white colour for special quality with flush tank merged without any joints, S Trap with slim hydraulic soft close seat cover with internal fittings including labour for fixing neat finishing etc complying with standard specification and as directed by the departmental officers (The quality of materials and design is approved by the departmental engineer before use on works).

Supplying and fixing with Superior quality Health Faucet of approved quality and brand for fixing in position etc., complete complying with standard specification and as directed by the departmental officers at site of work.

Supplying and fixing in position Superior quality (Heavy Duty) swan neck tap of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying and fixing in position Superior quality (Heavy Duty) Two way tap of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying and fixing Stainles steel wall mounted Toilet tissue paper stand of make with necessary wall brackets of same materials of ISI Specification of approved quality including cost of teak wood plug and CP screws etc., complete complying with standard specification and as directed by the Departmental officers.

Supplying and fixing Stainles steel wall mounted Toilet Roll Holder of make with necessary wall brackets of same materials of ISI Specification of approved quality including cost of teak wood plug and CP screws etc., complete complying with standard specification and as directed by the Departmental officers.

Supplying and fixing with Superior quality Angle Cock Tap of approved quality and brand including for labour charges in position etc., complete and as directed by the departmental officers.

Renewing and refixing with new S.S bottle trap of approved quality and make including labour for fixing in position etc complete complying with standard specification and as directed by the departmental officers at site of work.

Supplying and fixing position PVC Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Renewing and laying and jointing UPVC Pipe (Un-Plasticized Polyvinyl Chloride) UPVC used for residential and home applications, water pressure in residential areas do not normally exceed the maximum tolerance. (schedule-40) but excluding cost of such specials and fixing in position dismantling masonry and make the same to original condition etc complete complying with standard specification and as directed by the departmental officers at site of work.

20mm dia UPVC Pipe

25mm dia UPVC Pipe

Supplying and fixing in position best quality PVC soil/waste pipes of various dia having 6 kg/sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC/MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry/RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

75mm dia PVC Pipe

110mm dia PVC Pipe

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

75mm dia PVC Elbow with Door

110mm dia PVC Elbow with Door

75mm dia PVC Elbow

110mm dia PVC Elbow

75mm PVC Tee with Single Door

110mm PVC Tee with Single Door

100X75MM PVC REDUCER

Supplying and fixing in position of CP shower Arm with Overhead shower Rose of approved quality and brand including labour Charges for fixing in position etc complete

Supplying and fixing new one of best approved quality SS soap tray of size 150x150mmx50mm including cost of rawel plug, brass screws etc., complete complying with standard specification and as directed by the Departmental officers.

Supplying and fixing with new one of approved best quality SS towel rod of 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing with new one of Superior quality Standard Towel Ring of approved quality and brand for fixing in position etc complete complying with standard specification and as directed by the departmental officers at site of work.

Supplying and fixing in position first quality and approved variety of UPVC Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

UPVC Valve 25mm dia

Supplying and fixing wall mounted Vanity wash hand basin Cabinet type with Two Drawers, Solid Wood Frame and door shutter arrangements, best and approved quality and including necessary furniture fittings such as handle lock The labour charges for making and fixing in position of the size etc.complete complying with standard specification and as directed by the departmental officers.

Easing the existing over hanging doors and windows including nerewing frame its position and refixing the same after attending petty repair works including for wrough and putup in position fixing necessary furniture excluding cost of aurniture etc., complete complying with standard specification as directed by the departmental officers at site of work.

Supplying and fixing with new one of Hydraulic Door closer of various sizes of approved quality using Aluminium Extruded section body tubular type universal hydraulic door closer with double speed adjustment like HARDWYN (make) 'GAZEL' (or) equivalent (with ISI Monogram) brand including labour charge for fixing inposition etc.,

Supplying and fixing with new Heavy type Long neck door stopper of best and approved quality including labour charges for fixing in position etc, complete with standard specification and as directed by the departmental officers.

Supplying and fixing the cupboard lock with new cupboard lock of best and approved quality including labour charges for fixing in position etc, complete with standard specification and as directed by the departmental officers.

Supplying and placing the bed mattress of size 2100 mm × 2030 mm × 200 mm thickness, made of soft material, Medium-Soft type with 7-Zone support and enhanced breathability, using 100% natural latex with pin holes. The latex layer shall be breathable, supportive and comfortable, made from naturally sourced latex foam. The mattress shall include an Aeroflow Transition Foam layer using high density foam transition material for added breathability, comfort and responsiveness, High Density Foam with DeepTouch™ Pressure technology, and a Super High Density Foam layer for stability — made of durable material that maintains the center of gravity and provides structural stability to the mattress — along with linen side walls made of high-quality linen fabric with strong knitted streaks to protect the mattress and keep it looking classy.” etc, complete and as directed by the departmental officers

Repairing and reupholstering the Wooden Cushion Chairs by assessing the damaged areas by checking for loose Joints, broken legs, on Cracked frames by disassembling the chairs and replacing the damaged parts and reassembling and ensuring all parts are securely attached. Reupholstering includes removing old cushion in the Chair seat and backrest and attaching new cushion of approved quality, design and colour on the chair frame using Screws or Staples to secure the cushion in place. The rate inclusive of Cost of materials, Cast of labour for repairing Upholstering

Repairing and reupholstering the Dressing Cushion Stool with armrest by assessing the damaged areas by checking for loose Joints, broken legs, on Cracked frames by disassembling the chairs and replacing the damaged parts and reassembling and ensuring all parts are securely attached, and attaching new cushion of approved quality, design and colour on the chair frame using Screws or Staples to secure the cushion in place. The rate inclusive of Cost of materials, Cast of labour for repairing Upholstering

Repairing and reconditioning the existing 3-seater Sofa including renewal of upholstery cloth of approved quality and brand, replacement of damaged seat and back cushions, carrying out all necessary repairs, stitching of upholstery cloth, and finishing the sofa to its original condition with neat workmanship. The rate shall include cost of materials, labour charges, and all incidental charges, complete, complying with standard specifications and as directed by the departmental officers.

Repairing and reconditioning the existing 2-seater Sofa including renewal of upholstery cloth of approved quality and brand, replacement of damaged seat and back cushions, carrying out all necessary repairs, stitching of upholstery cloth, and finishing the sofa to its original condition with neat workmanship. The rate shall include cost of materials, labour charges, and all incidental charges, complete, complying with standard specifications and as directed by the departmental officers.

Repairing and reconditioning the existing Single seater sofa including renewal of upholstery cloth of approved quality and brand, replacement of damaged seat and back cushions, carrying out all necessary repairs, stitching of upholstery cloth, and finishing the sofa to its original condition with neat workmanship. The rate shall include cost of materials, labour charges, and all incidental charges, complete, complying with standard specifications and as directed by the departmental officers.

Supplying and fabricating and placing in position of M.S Hollow square section of 100mm x 100mm x 6mm thick at 16.98 kg/m, below ground level 0.30m above the ground level 0.70m below ground level 0.30 x 0.30 x 0.30 earth work excavation and P.C.C 1:2:4 ground level of bottom gusset plate 0.30m x 0.30m x 6mm thick hollow square section top closing 100mm x 100mm x 6mm thick with necessary cutting and welding with required size including labour charges for fixing with materials etc., complete complying with standard specification and as directed by the departmental officers.

Fabricating, Supplying and fixing in position Mosquitonet arrangements of Openable type. The Outerframe shall be made with Powder coated AluminiumNatural colour matt finishAluminium Hollow sectionof size 31mmx40mmx1.55mm. The Vertical center Mullion made with Aluminium Hollow section of size 55mmx11mmx1.55mm.The Horizontal and Vertical Aluminium Hollow section Shutter frame of size 31mmx 13mm with a thickness of 1.55mm. The Mid Horizontal Aluminium Hollow section frame provided in the shutter with a size of 10mmx11mmx1.55mm. The Epoxy coated Stainless Steel 304 grade wire mesh with dia of 0.19mm shall be provided for Net. The U shaped Aluminium handle provided in the each shutter with a size of 19mmx26mm. TheConnection Mechanism between Shutter and Outer frame that enables opening the Mosquito net. TheMosquito net arrangement should be fixed to thewindow with 100% packing with Screws, Silicon packing all around the frames with including cost of all materials, labours, power consumption requiredfor fabrication, drilling holes in RCC column/wall, masonry walls, Window frames, wherever necessary with drills to the required extent and make good to the original conditions after fixing and also as directed. All the Aluminium sections are to the powder coated with matt finish under electrically controlled conditions in accordance with relevant IS Code etc.complete complying with standard specification and as directed by the departmentalnofficers.

Supplying and fixing in position of Long body tap with new Long bodytap of approved make conforming to IS spn. And quality including cost of shellac, thread, cutting and threading wherever necessary etc., complete.

Supplying and fixing of Touch Translucent Roller blinds work using 0.37mm thick translucent (Touch) roller fabric with 100 percent polyster and acrylic coarting, moisture resistance type sponge able care instruction, 190 grams / sqm and 10 percent sound observation. The roller blinds to support aluminium section 38mm dia round pipe with electro colour anodised and bottom powder coated aluminium section 25mm dia round pipe. The control unit with operation chain (gear) 38mm x 38mm powder coated metal steel brackets 3mm tape with plastic 0.8mm thick plate and 25mm end caps for bottom round pipe. The quality and colour for the all items involved are got prior approval from the Engineer before use on work with necessary hardware's erection at your site including all labour cost etc., complete as directed by the departmental officers (including all taxes).

Supplying and fixing of Zeebra blind made out aluminium alloy pelmet with necessary control unit with accessories etc., Fabric composition of 100% polyester with weight of 205 g + 5% per m2 fabrics are fire retardant against Korea fire equipment inspection against Korea fire equipment inspection corporation passed complying with standard specification and as directed by the departmental officers.

Providing window Sheer curtains made of unique copper design soft and heavy duty fabric of using M track channel, special features like room darkening, thermal insulation, wrinkle free, black out and grommets, light filtering, Sun UV protection polyster curtains made using durable polyster blends along with sturdy hanging system to ensure long lasting perfection along with user friendly plastic pull-down chain for easy usability etc., The rate is inclusive of cost materials, labour charges and transporting charges, fixing charges etc, complete. The materials quality and design is approved by the Executive Engineer before use on works.

Supplying and fixing high quality WPC (Wood Plastic Composite) soffit panel of 300mm width and 6mm thick finished with walnut colour. The WPC soffit panel installed using J-Channel with screws and fasteners available for secure panel installation in accordance with the instructions as directed by the departmental officers. The rates including labour charges, cost of materials, loading, unloading and conveyance charges etc, Complete complying with standard specification. (The material will be got approved by the Executive Engineer before use on work)

Renewing the damaged wall panelling using 2"x1" Aluminium Channel at 2'0" intervals on both directions and fixing to the single side 12mm thick high density anti terminate water proof plywood partition of approved quality and brand using necessary screws and nails etc., complete complying with standard specification and as directed by the departmental officers at site of work.

Renewal and refixing of Fluted wall panelling with 12mm thick Grey charcoal panels with uniform dual tone design as approved by the departmental officers and the rate inclusive of cost of materials including necessary screws and nails adhesive and labour charges, fixing charges etc. complete complying with standard specification.

Painting two coats to the walls with (Interior) Plastic Emulsion Paint with putty including removing the existing old paint materials if any from the wall surface using the scrapping materials such as Iron brush, emery sheet, rough nice and cleaning the wall surface etc., after finishing the scrapping work to be apply with one coat of water base primer then applying with two or more coat of putty with necessary scrapping charges up to final smooth finishing etc., finally painted the wall surface with two coats of Plastic Emulsion Paint of approved and colour and quality. The rate is inclusive of cost of materials labour charges and transporting charges etc., complete and as directed by the departmental officers.

Painting two coats to the walls with Royal Emulsion Paint with putty including removing the existing old paint materials if any from the wall surface using the scrapping materials such as Iron brush, emery sheet, rough nice and cleaning the wall surface etc., after finishing the scrapping work to be apply with one coat of water base primer then applying with two or more coat of putty with necessary scrapping charges up to final smooth finishing etc., finally painted the wall surface with two coats of Royal Emulsion Paint of approved and colour and quality. The rate is inclusive of cost of materials labour charges and transporting charges etc., complete and as directed by the departmental officers.

Repainting the water proofing coating for terracota tile with ready mixed water proofing paint two coats over one coat of crack paste over one coat cement paint including through scrapping clean removal of dirt, etc., complying with standard specifications and as directed by the departmental officers. (The colour and shade of the ready mixed water proofing paint shall be got approved by the Executive Engineer before use of work).

Painting Old iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with Two coats of best approved first quality and colour of synthetic enamel paint in all floors etc., complete complying with standard specification and as directed by the departmental officers.(The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Removal of the existing pre-laminated sheet and refixing a new pre-laminated sheet to the existing table of size 1800 mm × 750 mm, provided with 10 mm thick plain glass with half-round nosing, carefully removing and fixing without any damage, using approved-quality adhesives such as Fevicol or equivalent approved brand, completing all connected works as directed. The rate includes the cost of removing and refixing the material, labour charges, and all tools and plants required for completing the work, complete and as directed by the departmental officers

Supplying and fixing and Brass Tamil Font of 150mm and 10mm thick with new letters made up of brass moulding with laser cut edges, polishing etc., complete and also provided lacquer coating for smooth finish. The rate inclusive of materials, fabrication , fixing for neat alignment,etc., complete as directed by departmental officers.

Supplying and fixing inpoition of unitex matt [Red colour] including conveyance spreading and as directed by the departmental officers including labour charges for removing the same after the function is over etc., complete

Repainting the old tiles flooring two coat with best MRF paint with superior quality colour and brand to be approved by the deptl. Officers and cost of brushes etc., complete.

Providing and fixing 12 mm thick plain WPC wall panelling of approved colour and design, including thorough surface preparation, fixing 2" × 1" aluminium channels as the supporting framework firmly to the existing wall surface, and fixing the plain WPC panels over the aluminium channels using approved-quality adhesives such as Fevicol / WPC adhesive / equivalent approved brand, ensuring proper alignment, level finishing, tight joints and neat edge finishing with matching WPC/PVC beading, including cutting, shaping, labour charges, tools and plants, all complete and as directed by the departmental officers

Providing and fixing a Wood Slat Room Divider using solid Red Oak slats of approved width and thickness, neatly finished and fixed directly to the existing surface using approved-quality adhesives and stainless-steel screws, ensuring proper spacing, alignment, plumb and smooth finishing with matching wooden edge trims/beading. The gap between the slats shall be maintained between 0.5 inch to 2 inches (2 cm to 5 cm), and for proper visual balance the spacing shall always be less than the width of the slat. The slat width generally ranges from 1 inch to 2 inches as per the design requirement. The work includes all materials, labour, cutting, shaping, tools and plants, all complete and as directed by the departmental officers

Providing and fixing 12 mm thick Corian top of approved colour and design, using genuine solid-surface sheets of approved brand, including cutting, edge profiling, joining with matching adhesive, grinding, buffing and polishing to achieve a seamless finish, fixing over the existing platform/table using approved-quality adhesive, ensuring proper alignment, level finishing and neat edges. Corian is scratch-resistant, stain-resistant, and heat-resistant, standing up to the wear and tear of everyday life with ease, ensuring durability and ease of maintenance. The work includes all materials, labour, tools and plants, all complete and as directed by the departmental officers

Painting New Plastered Wall Surface with One finishing coats of ready mixed (Emulsion) of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and fixing superior-quality waterproof, anti-skid rubber mat feet of approved brand and specification. Made from high-quality PVC rubber, these mat feet ensure, Easy to Clean: Simply wipe or hose off the mat for quick and effortless cleaning, maintaining hygiene and cleanliness. durability and longevity even with regular use. The rate includes all associated charges, including loading and unloading, transportation, cutting, tools, and plants, complete.

Supplying and fixing in position of cup-board shutters made of Teak wood scantlings of size 100mm x 32mm for outer frame, horizontal and vertical members. The shutter frame is made out of 75mm x 32mm of Teak wood scantling (horizontal - 3 Nos., vertical - 2Nos. for each shutter) with 19mm thick hi-density water proof anti terminate plywood, single side pasted with 1mm thick prelaminated sheet (natural) single side pasted with 1mm thick prelaminated sheet (white) side The shutters are fixed to the frame with required 6 numbers of aluminium hinges 100x30mm, 2 Nos. D type aluminium handle 100mm, 2 Nos. of aluminium tower bolts 75x10mm, 1 No. of cupboard lock, etc. The teak wood frame shall be painted two coats with synthetic enamel paint over one coat of wood primer. The pre-laminated Sheet and furniture fittings used should be got approved by the Engineer incharge before use. The cost includes cost of all materials labour charges etc.

Removal and refixing of the existing 3-seater wooden armed wire-netted chairs, including carefully dismantling the damaged wire netting without causing any damage to the wooden frame, removing the old worn-out netting, and supplying and fixing new branded wire netting of approved quality. The work also includes providing and fixing new bushes of approved quality, ensuring proper alignment, firm fixing, and neat finishing, all complete as per standard specifications and as directed by the departmental officers.

Paving the floor with best quality Vitrified Parking Tiles of following size 600mm x 600 mm x 20mm and variety and water absorbtion less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing two legged pipe scaffolding using 40mm first class M.S. pipe including fixing cross bracings, couplings, EJP couplers for cross bracing and base plates including erection of scaffolding, conveyance charges, loading and unloading charges and dismantling after completion of the work and removing from the site etc., as directed by the departmental officers.

Painting the wall with Texture Finish Paint including labour charges with neat finishing etc., Complete complying with stanadrd specification and as directed by the departmental officers.

Painting the wall with two coats of approved Superior weather - resistant Exterior Emulsion paint over the one coat of primer on cement plastered wall surface ect., complete complying with standard specification and as directed by the departmental officers.

Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9)grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer

Supplying, fabricating, and fixing 20 mm thick toughened plain glass for ceiling high-strength quality, having approximately three times higher tensile strength and five times higher impact resistance compared to annealed glass, and significantly stronger than heat-strengthened glass. The toughened glass shall possess high load-bearing and thermal resistance capacity, making it suitable for applications where strength and temperature resistance are critical. It shall have higher edge strength to resist thermal breakage caused by sudden temperature variations and shall be suitable for spider fittings and point-fixed glazing systems. The glass may also be provided with acoustic properties where required for enhanced privacy and sound insulation. All joints between glass panels shall be sealed with high-quality epoxy grouting to ensure structural integrity and leak-proof installation. In addition to its functional advantages, the toughened glass shall offer aesthetic flexibility and be suitable for modern interior and architectural applications, complete with all fittings, supports, labour, tools, and accessories as per approved drawings and site requirements, complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Supplying and fabricating the plasing in position main special type of teak wood door Vertical frame size of the 0.13m x 0.045m Top Horizontal the frame size of the 0.13m x 0.045m and Middle Horizontal the frame size of the 0.13m x 0.045m with shutter styles vertical 0.10mx0.04m and Bottom Horizontal the frame size of the 0.15m x 0.045m, intermediate- door panels using 35mm thick teakwood planks, and fixing with special type of foldable brass hinges 200mmx100mm labour charges for wrought and put up hire charges for tools and plants including labour charges for making door with materials etc, complete, complying with standard specification and as directed by the departmental officers.

Supplying and fixing wall cladding using approved quality Italian marble for exterior walls to give a sleek and contemporary appearance. Large marble slabs with minimal veining shall be used for a modern, clean look that complements minimalist architecture. Dark-toned Italian marble may be used to create a rustic and earthy appeal, harmonizing with greenery and outdoor spaces. The marble slabs shall be fixed in cement mortar (1:2) with crushed stone sand, 10 mm thick, with the addition of mortar plasticizer. Joints shall be pointed neatly with water-resistant tile epoxy grout at the rate of 0.27 kg/sq.m. The work shall include curing, finishing, and all labour, tools, and materials complete, complying with standard specifications and as directed by the departmental officers. The make and brand of marble slabs shall be approved by the Executive Engineer before use.

Uprooting rang vegetation and weeds by digging the area to a depth of 30cm removing all weeds and other growth breaking clods rough dressing flooding with uprooting fresh growth after 10to 15 days and then fine dressing for planting new grass including disposal of all rubbish with all leads and lifts etc, complete by the departmental officers

Supplying ,spreading and mixing red earth , and manure mixture with required base 0.12m of chemical for control of pest and disease like neem cake and carbofureden and fertilizers for root regulator like DAP urea and super phosphate and for mind the mix cost of red earth sand fertilizers and labour charges etc., complete directed by the Departmental officers.

Make Lawn mixcigan grass including forking the ground top dressing with sludge manure of fertilizers mixing with the same width forked soil watering, weeding and maintenance for a period of 30 days or more from the date of completion of planting work etc complete.

Supply, Installation, Testing and Commossioning of Outdoor type Automatic Control Panel with water proof MS sheet power box including openable double door with locking arrangements powder coated finish along with – 1no. Incoming MCB,4no. Outgoing MCB, 4no. Starter with O/L Relay for Pump, 1no. Single Phase Preventor, 2no. MCB for Lights, 2no. 230v/12v DC Power supply for Lights, 2no. RGB Controller,1no. Logical Controller Unit for Sequencing of Fountain Effect (for 5mtr dia Pod) 2no. 24Hr Timer for Fountain Auto ON/OFF Operation including Panel wiring etc., as required, Indicating Lamps including Panel internal wiring etc,. as required. The rate inclusive of cost of materials, transportation, labour for fixing, testing, time setting, etc., complete as directed by the departmental officers.

Supply, Installation, Testing and Commissioning of Fountain Foam Jet Nozzle- 35mm Orifice, 1" BSP-MOC SS 316 with Internal Air/Water Ratio Adjusment, Ball joint - 1" BSP- MOC Brass with Chromium Plated finish. The rate inclusive of cost of materials, transportation, labour for fixing, testing, etc., complete as directed by the departmental officers.

Supply, Installation, Testing and Commissioning of Fountain Aerator Jet Nozzle - Column of Frothy, aerated water made up of cast bronze and brass with internal air/Water Ratio Adjustiment, Ball joint - 1" BSP- MOC Brass with Chromium Plated finish. The rate inclusive of cost of materials, transportation, labour for fixing, testing, etc., complete as directed by the departmental officers.

Supply, Installation, Testing and Commissioning of Fountain Calyx Jet 2" BSP-madrial made up of PVC/SS combined Nozzle with internal air/Water Ratio Adjustiment, Ball joint - 1" BSP- MOC Brass with Chromium Plated finish. The rate inclusive of cost of materials, transportation, labour for fixing, testing, etc., complete as directed by the departmental officers.

Supplying, fabricating, installing of Fountain Ring 2' dia wih adjustable fountain ring nozzle - MOC Brass with nickel coated finish 1/4" BSP and 4mm orifice with O-ring, fabricated out of Stainless steel 304 Pipe (1-1/2") of size 2'-0"dia act as supports and water conducting tubes to the nozzles, the ring bottom with supporting leg arrangements to be on fountain floor. Sprit level to be maintained at to of ring to obtain uniform discharge in all outlets. The delivery jet nozzle to be fixed with the SS ring with necessary drilling holes, fixing of pipes with welding in neat intervals as design provided, the fabricated ring to be tested at full discharge, tested for leakages, The rate inclusive cost of all materials including necessary Process Bending, Shaping, Welding, Drilling, Tapping and screwed. Brass Adopters, Main Feeding arrangements and Supporting Legs as required, etc., complete as directed by the departmental officers.

Supplying, fabricating, installing of Fountain Ring 3' dia wih adjustable fountain ring nozzle - MOC Brass with nickel coated finish 1/4" Fabricated out of Stainless steel 304 Pipe (1-1/2") of size 3'-0"dia act as supports and water conducting tubes to the nozzles, the ring bottom with supporting leg arrangements to be on fountain floor. Sprit level to be maintained at to of ring to obtain uniform discharge in all outlets. The delivery jet nozzle to be fixed with the SS ring with necessary drilling holes, fixing of pipes with welding in neat intervals as design provided, the fabricated ring to be tested at full discharge, tested for leakages, The rate inclusive cost of all materials including necessary Process Bending, Shaping, Welding, Drilling, Tapping and screwed. Brass Adopters, Main Feeding arrangements and Supporting Legs as required, etc., complete as directed by the departmental officers.

Supply and Installation of Horizontal openwell Submersible pumpset 2880 RPM operating on 3 phaase 2.2KW/3.0 HP with Discharge 900LPM, 8mtrs head, suction and delivery size 80x80 with Cast iron body & Impeller, Stainless steel shaft & Suction screen for Fountain operating on 3 phase 415V AC Supply with suitable pipe connection and suction unit covered with stainless steel screen mesh as required, the rate inclusive of cost of pump, transportation, labour charges for fixing, testing, electrical wire connection, etc., complete as directed by the departmrntal officers.

Supply and Installation of Horizontal openwell Submersible pumpset 2880 RPM operating on 3 phaase 2.2KW/3.0 HP with Discharge 900LPM, 8mtrs head, suction and delivery size 80x80 with Cast iron body & Impeller, Stainless steel shaft & Suction screen for Fountain operating on 3 phase 415V AC Supply with suitable pipe connection and suction unit covered with stainless steel screen mesh as required, the rate inclusive of cost of pump, transportation, labour charges for fixing, testing, electrical wire connection, etc., complete as directed by the departmrntal officers.

Supply and Installation of Horizontal openwell Submersible pumpset 2880 RPM operating on 3 phaase 3.7KW/5.0 HP with Discharge 720LPM, 12mtrs head, suction and delivery size 80x65 with Cast iron body & Impeller, Stainless steel shaft & Suction screen for Fountain operating on 3 phase 415V AC Supply with suitable pipe connection and suction unit covered with stainless steel screen mesh as required, the rate inclusive of cost of pump, transportation, labour charges for fixing, testing, electrical wire connection, etc., complete as directed by the departmrntal officers.

Labour and material charges for Interconnecting Plumbing works for small fountain ( 3meter dia) pipe line from submersible Pump to Fountain Main nozzle, Stainless steel Circular rings of size 3' dia and 2' dia with equal distribution without any leakages using UPVC pipes, UPVC fitting and regulating UPVC ball valves, cleaning water discharge outlet as required. The rate inclusive of cost of UPVC pipe materials, labour charges, testing, etc., complete as directed by the departmental officers.

Labour and material charges for Interconnecting Plumbing works for small fountain ( 5 meter dia) pipe line from submersible Pump to Fountain of each nozzle as per nozzle location with equal distribution without any leakages using UPVC pipes, UPVC fitting and regulating UPVC ball valves, cleaning water discharge outlet as required. The rate inclusive of cost of UPVC pipe materials, labour charges, testing, etc., complete as directed by the departmental officers.

Providing water proof Submersible cables of best quality and brand with ISI specifications. The wiring consists of 3c x 2.5sqmm for fountain pump, 4c x 2.5sqmm FRLSH round cable for LED Lights (6 nos LED fittings), 2.5sqmm wire for earthing with suitable PVC conduit pipes from Fountain to control panel of best quality, suitable sizes for Pumps & Lights with suitable PVC Conduit pipes of best quality from Fountain Pond to Fountain Controller unit as required. The wire connection is layed below ground level from the control pannel and in fountain under water open wiring without any damages. the rate inclusive of cost materials, labour for connection charges, testing, etc., complete as directed by the departmental officers.

Providing water proof Submersible cables of best quality and brand with ISI specifications. The wiring consists of 3c x 4sqmm for fountain pump, 4c x 2.5sqmm FRLSH round cable for LED Lights (11 nos LED fittings), 2.5sqmm wire for earthing with suitable PVC conduit pipes from Fountain to control panel of best quality, suitable sizes for Pumps & Lights with suitable PVC Conduit pipes of best quality from Fountain Pond to Fountain Controller unit as required. The wire connection is layed below ground level from the control pannel and in fountain under water open wiring without any damages. the rate inclusive of cost materials, labour for connection charges, testing, etc., complete as directed by the departmental officers.

Supplying and fixing of Stainless steel 304 Underwater light fitting of best quality and make Colour-RGB 230V/18W LED bulb, The light fitting to be in 150mm dia, 32mm thick with center hole open 1 inch with follwing specification. The LED fitting provided with 0.5sqmm 4 core water proof under water cable and fitting top covered with Acrylic with silicon and polyurathene screws, chord seal cable entry with Stainless steel fixing brackets as required. The rate inclusive of cost of materials, transportation, labour for fixing, testing, etc., complete as directed by the departmental officers.

Providing, fabricating, assembling, erecting, and fixing of Mild Steel Structure compromising of adequate section such as MS plates, channels, ISMB, ISHB, ISWB angles, Building up of new sections as per requirements, Stay cables wherever required, Anchor bolts aluminium extruders etc. conforming to IS 2062-grade A/B at all elevations, levels and heights including aligning, leveling, straightening, cutting, welding, bending to shape, bolting, as per approved design specifications. Fabrication involves connection using plates, channel and angles ,gussset plate, foundation bolts, cleats and fastners to Main structure wherever necessary The rate includes scaffolding charges and different types of powder coated structural steel tubes of grade YST 210 conforming to IS 1239 and IS - 1161 and also the rate shall include for powder coating of all the members 50 microns thickness complete and as directed by the departmental officers. The tenderer shall design canopy structure in detail, based on the orders of the departmental officers, without altering the architectural profile and submit the detailed design calculation independently. Proof checked and submitting the same and getting approval from the Executive Engineer before commencement of the work is mandatory.Payment for assembly and erection shall be done on weight in Kilogram basis.

Providing and fixing Glass Reinforced Concrete (G.R.C) ornamental Screens casted with 'Spray Mix' concrete design in approved size, pattern, Thickness (Border 40-50m Thick & Internal Member 25-30mm thick) and shade.

The Screens should be made from '53 grade' White Portland Cement manufactured by 'JK Cement' or 'Birla white', White Quartz fine graded sieve Silica sand, Alkali Resistant Glass Fiber manufactured by 'NEG Japan, Owen corning 'Saint Gobain' or equivalent, Super Plasticizers manufactured by 'Karochem' or equivalent, Polymers manufactured by 'Nova Polychem or equivalent and U.V resistant Synthetic inorganic pigments should be used for pigmentation manufactured by 'Phenochem industries or equivalent. The Screens casting shall take place with layering methodology using-Direct power spray machines. The GRC Screens flexural strength average L.O.P should be above or equivalent to 6 N/mm2 & M.O.R should be above or equivalent to 12N/mm2 for tests done on 28 days cured samples. The fixing of Screens should be done using 'Dry fixing' method onto structural support mambers i.e. R.C.C, Brick work or Red oxide primer-paint or Epoxy primer-paint treated mild steel. The fixtures, fasteners and self tapping screws to be used for dry fixing should be of HILTI/KLIMAS/Fischer. The quantity of fasteners or self tapping screws shall be calculated in accordance to the weight of Screens and actual site fixing conditions. If there will be a requirement of Joint filling then Elastometrtic exterior grade paintable PU sealant will be used. For final finishing of Screen one weathershield exterior grade water based diluted paint coat will be done if required. Vendors shall submit shop drawings of the same, the drawings to be duly approved by the

Providing Stone seating bench made up of Granite Stone or Equivalent with sculpture works made with skilled stone sthapathis. The individual pieces shall be fixed to each other with adequate bonding adhesives like Aralddite or Equivalent. Stone varnish shall be applied to the stone bench to provide appealing look. The pattern and design of Stone Bench shall be got approved by the Executive Engineer before use on works.

Supplying, fabricating, and fixing 12 mm thick toughened glass windows of high-strength quality. The 12 mm thickness provides exceptional strength, creating a robust barrier while allowing natural light. Unlike traditional perceptions of glass fragility, 12 mm toughened glass windows are highly durable and safe. The glass shall be capable of withstanding compressive stresses above 90 MPa and shall be significantly stronger than annealed or ordinary glass. It shall be uniform in thickness, with low impurity content, providing enhanced mechanical strength, thermal resistance, and safety. All joints shall be sealed with high-quality epoxy grouting to ensure structural integrity and leak-proof installation. The work shall include all necessary frames, fittings, supports, labour, tools, and accessories as per approved drawings and site requirements. complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing and fixing of FRP Gratings of 600 x 300mm size with M.S flats of 25x10mm for outer frames, 25x6mm for inner braces and PVC pipe 150mm dia fixed with mild steel grating, including cost and coveyance of pipes and gratings and fixing them in position (At 5m interval)

Flooring with Self design Joint free rectified Ceramic Tiles of size 305 x 305 x 8mm laid over 20mm thick cement mortar 1:3 (Onecement and Tree sand) base mortar over the existing slab / floorincluding cutting the tiles to the required size with special cutterwherever necessary, laying in positionand and pointing with whitecement mixed with colouring pigment at the rate of 0.3 kg. / sq.m.etc., complete complying with standard specification. (The makeand brand of the tiles should be Johnson / Kajaria / Somany / Nitco/ RAK or Equivalent which has to be got approved by executiveEngineer before use on works)

Dadooing walls with Joint free rectified Colour designed digital print ceramic tiles, with borders, with size of 300mm x 600mm x 10mm and above setin Cement Mortar 1:2 (One Cement and Two sand) 20mm thick andpointing the joints with white cement mixed with colouring pigmentsat the rate of 0.40 Kg. / Sq.m. nbatly in all floors, curing, etc,,complying with standard specification and as directed by thedepartmental officers. (The make and brand of the tiles should belike Johnson / Kajaria / Somany / Nitco / RAK or Equivalent whichhas to be got approved by Executive Engineer before use on works)

Supplying and fixing in position of Steel fibre reinforced cement concrete (SFRC) manhole / inspection chamber cover slab with following frame sizes including necessary labour charges for fixing the frame in position over the cement mortar base and finishing the joints etc. complete as directed.

Supplying UPVC Specials in water supply arrangements (both in internal and external water supply arrangements

40mm dia upvc Elbow

40mm dia UPVC Tee

40mm dia UPVC Union

Supply and delivery of clear water vertical wet type submersible pump (5HP) suitable for 100 / 150 mm dia borewell conforming to IS 8034/2002 as amended thereafter and BEE 3 Star Rated capable of discharging noted LPM against head of water column due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze or Cast SS impeller, brass screws and CI FG 200 grade pump bowl/diffuser with ISI mark. The pump shall be directly coupled to a continuos rated two pole suitable wet type vertical squirrel cage induction motor as per IS 9283 /1995 and as amended there after, suitable for operation in AC three phase 415 V+/- 10 %, 50 HZ +/- 5 %

Supplying and fixing of 3 Phase Panel Board including labour charges complete to suit the need (The pump set should be got approved by the Executive Engineer before supply)

Supplying and fixing and connecting of 4 core 16 sq.mm Flat Sub mersible cable wire for the sub-mersible motor from panel board to sub-mersible pump.

Supplying and planting the following varieties of plants as directed by the departmental officers , plants of height 150 mm to 200 mm, including soil preparation, mixing of compost and river sand in suitable proportion, planting in position, watering and maintenance of the planted area for the required period including replacement of dead plants, weeding, and cleaning of the bed, and application of organic fertilizer (vermicompost or cow dung manure) during maintenance; the rate including cost and conveyance of all materials, labour charges for planting, leveling, watering, and cleaning after completion of work, etc., complete, complying with standard specification and as directed by the departmental officers.

Pandanus

Euphorbia Red

Lantana

devil backbone

Ixora chinensis plants

Madagascar Periwinkle (Catharanthus roseus) plants

Construction of INSPECTION CHAMBER size of 600mm x 600mm including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of Clay burnt Bricks of size 9” x 43/8” x 23/4” with Class designation of 7.5 and Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification.

Providing & Fixing Staircase hand rail made out of 50.80mm dia stainless steel tube of 1.60mm thick at required locations to a height of 1000mm from finished floor level, welded to 38.10mm dia S.S.tube post of 1.60mm thick as vertical at 1m centre to centre with 3 nos of 25.40 mm dia horizontal S.S.tubes of 1.60mm thick in between as per details shown in the drawing and as directed. Stainles Steel Handrails with 10mm thk Ornamental stained glass or designed etched glass panelling - rate including fixing of glass panel , SS Clip , fixtures and labour charges for fixing of handrail in proper position. Rate shall include for grouting into concrete with necessary supporting arrangements in hand rail vertical and in floor, welding the base cup of post into slab reinforcement polishing, buffing and protecting the hand rail surface etc. complete as directed by the departmental officers.

Providing and laying 50 mm thick granite stone slab flooring of size 600 mm × 600 mm in portico / parking area, using hard, dense, durable and machine-cut granite stone, free from cracks, cavities and structural defects, with uniform colour and texture, conforming to relevant specifications and IS codes. The granite slabs shall be machine-dressed on all sides with true right angles and uniform thickness, and the exposed surface shall be flame finished / bush-hammered to obtain a non-skid finish suitable for vehicular traffic. The slabs shall be laid over an approved and properly prepared cement concrete base, to correct line, level and slope, on 20 mm thick cement mortar bed of proportion 1:4 (one cement : four sand) or over cement slurry, as directed by the Engineer-in-Charge. The slabs shall be properly set, pressed and tapped to achieve full bearing without hollow sound. Joints shall be uniform and shall not exceed 3 mm, and shall be filled with neat cement slurry or approved polymer-modified grout matching the shade of granite. The flooring shall be capable of withstanding heavy vehicular loads such as ambulances and service vehicles, and proper drainage slope shall be ensured in the portico area. After laying, the flooring shall be cured for a minimum period of seven days and protected from damage. The rate shall include the cost of materials, labour, tools, curing and all incidental charges, complete as per specification and as directed by the Engineer-in-Charge.

Paving the floor with best approved quality fine polished Granite Stone Slabs of following size and Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., complete complying with standard speicification and as directed by the departmental officers.(The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification and as directed by the departmental officers.

Providing and laying , spreading and compacting graded stone aggregate to wet mix macadam 200mm thick specification inculding premixing the materials with water at OMC in mechanical mix plant carriage of mixed materials by tipper to site laying in uniform layers with pavers in subbase /base course on well perapred surface and compacting with vibratory roller to achive the desired density including cost of materials, labour charges rental for machonery, fuel and all other incidental charges etc., complete as per clause 406 of MORTH Rev-5.

Labour charges for cleaning the floor with foam and vaccum cleaning with high power equipment using skilled labours. The rate includes cost of labour charges, material charges hire charges for machines etc complete complying with standard specification and as directed by the departmental officers.

Providing and placing L–type 6–seater modern sofa of overall size 2.35 m × 1.50 m (length) × 0.90 m (breadth); seat height – 0.45 m; back height – 0.85 m, upholstered with high–quality leatherette (faux leather) in dark brown finish. The sofa shall have cushioned seat and backrest, broad cushioned armrests with partial wooden finish on both ends, and an internal frame made of Silverwood with heavy–duty support, finished with a combination of wood and leather at both ends. Seating shall be provided with 100 mm thick latex foam + 25 mm super soft foam for enhanced comfort; backrest filled with Recron polyester material and fully finished with leatherette cover. Frame and foam interspaced with springs and 75 mm elastic tape for additional strength and seating comfort. All exposed surfaces shall be smoothly finished with concealed fasteners and high–quality workmanship. The entire work shall be carried out with precise cutting, neat fixing, and clean finishing, the rate including hire charges for tools and plants, labour, and all other incidental items, complete in all respects, in compliance with standard specifications and as directed by the departmental officers.

Supplying the Heritage type T.W Matt finish wooden chair of approved quality and brand, bottom seat covered with 100m thick, chair supports with good quality wooden joist leg and back rest using support with arm curved wooden material, and seating rest best quality foam with upholstery chair rest arm wood back support for comfortable person heritage type lock for elegant for room loading and varnishing the chair for matt finish using spray machine with neat finishing etc., loading and unloading transportation charges varnishing the chair for matt varnish finish with neat finishing etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing the special type Veneer Coffee Table in Dark Oak Finish size of the 1200m x 700mm x 410mm approved quality and brand, the table supports solid Oak wood, and table top herringbone pattern using mdf board and table bottom to be made on book rack the rate inclusive labour charges for fixing etc., table supported by solid wood tapered legs, the open storage complete transportation loading and unloading charges with neat finishing etc., complete complying with standard specification and as directed by the departmental officers.

Please Enable Macros to View BoQ information