Renovation of Office of Public Enterprises Selection Board PESB at Block No 14, CGO Complex, Lodhi Road New Delhi

S.No. Item Description Amount (DSR) Amount (NS)

2 Electro-Mechanical Works 12,56,075.00 44,77,564.86

3 Low Voltage works 41,10,209.10

4 Furniture 47,96,803.21

Add factor 6.33% for increase in GST @ 12 % to

18 % on DSR items 3,44,273.35

Digitally signed by RAHUL

SUMMARY THIRD FLOOR PESB

Renovation of Office of Public Enterprises Selection Board ( PESB) at

Block No: 14, CGO Complex, Lodhi Road New Delhi

SUMMARY OF COST FOR THIRD FLOOR

S.No. Item Description Amount (DSR) Amount (NS)

2 Electro-Mechanical Works 2,71,937.00

4 Furniture 12,03,636.26

Digitally signed by RAHUL

BOQ THIRD FLOOR DSR ITEMS

Renovation of Office of Public Enterprises Selection Board ( PESB) at Block No: 14, CGO Complex, Lodhi Road New Delhi

BILL OF QUANTITY FOR CIVIL WORKS-DSR BASED ITEMS - 3rd Floor

S No DSR 2021 No. Description Quantity Unit Rate Amount

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including

cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the

walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of

Engineer-in-Charge.

1.1 14.1.2 With Cement mortar 1:4 (1 cement:4 coarse sand) 41.08 Sqm 478.00 19,636.24

Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5

2 6.3 conforming to IS: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6

(1 cement : 6 coarse sand) :

2.1 6.3.1 With FPS (Non Modular) Bricks 6 Cum 8030.6 48183.6

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold

water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00

m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of

3 18.8 cutting chases and making good the same including testing of joints complete as per direction of

Engineer in Charge.

Concealed work, including cutting chases and making good the walls etc.

3.1 18.8.4 32mm nominal pipes 15 meter 712.75 10,691.25

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc.

4 18.11 concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making

good the wall :

4.1 18.11.2 20mm dia nominal bore 10 meter 541.10 5,411.00

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592

5 12.41 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal

expansion, (i) Single socketed pipes.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised

6 12.42 Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring

conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

6.1 12.42.1 Coupler

Digitally signed by RAHUL

BOQ THIRD FLOOR DSR ITEMS

6.3 12.42.4 Single Tee without Door

6.5 12.42.5 Bend 87.5 degree

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the

direction of Engineer-in-charge.

Providing and fixing C.P. brass angle valve for basin mixer and geyser

points of approved quality conforming to IS:8931

Providing and fixing C.P. brass long body bib cock of approved quality

conforming to IS standards and weighing not less than 690 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass

10 17.73 screws with concealed fittings

arrangement of approved quality and colour.

600 mm long towel rail with total length of 645 mm, width

10.1 17.73.2 78 mm and effective height of 88 mm, weighing not less 1.00 Each 600.35 600.35

11 17.34 Providing and fixing toilet paper holder :

Providing and fixing PTMT Waste Coupling for wash basin and sink,

of approved quality and colour

Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms

Digitally signed by RAHUL

BOQ THIRD FLOOR DSR ITEMS

Bathroom Counter Work

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform,

vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar

13 8.50 taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 1.00 Nos 808.15 808.15

Providing and fixing 18 mm thick gang saw cut, mirror polished,

premoulded and prepolished, machine cut for kitchen platforms, vanity

counters, window sills, facias and similar locations of required size,

14 8.2 approved shade, colour and texture laid over 20 mm thick base cement

mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching

pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss

finish etc. complete at all levels.

14.1 8.2.2 Granite stone slab of colour black, Cherry/Ruby Red

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine

polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Providing and laying water proofing treatment in sunken portion of

WCs, bathroom etc., by applying cement slurry mixed with water

proofing cement compound consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with

water proofing cement compound @ 0.253 kg/ sqm. This

layer will be allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed

with water proofing cement compound @ 0.126 kg/sqm. This

layer will be allowed to air cure for 4 hours followed with water

curing for 48 hours.

CLADDING AND TILING WORK

Digitally signed by RAHUL

BOQ THIRD FLOOR DSR ITEMS

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be

specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle

green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over

12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry

@ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the

manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand

& manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse

18 11.41A sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement

and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying

of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system

and rubber mallet for placing the tiles gently and easily.

18.1 11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the

manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand

& manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse

19 11.41A sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement

and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying

of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system

and rubber mallet for placing the tiles gently and easily.

Double charge vitrified tile polished finish of size

Size of Tile 800 x 800 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with

water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours &

shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse

sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement &

matching pigments etc. complete.

Size of Tile 800X800 mm

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of

21 11.48 organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling

/ grouting and finishing complete as per direction of Engineer-in-charge.

Digitally signed by RAHUL

BOQ THIRD FLOOR DSR ITEMS

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden

shade texture with following process in the sequence as detailed below: 1. The surface to be polished

is rubbed with sand paper 80/

120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and

allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying

of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess

sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with

22 13.116 special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to

dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12

hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and

melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry

surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final

melamine polish is applied with compressor pressure spray gun using melamine clear polish and

melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final

coat to be done in 1 or 2 layers without gap of time.)

Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above floor

level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit

23 12.31 wire mesh fixed to wooden frame (frame work to be paid separately):

Extra for sunk or raised mouldings in the plaster of Paris (Gypsum

anhydrous) ceiling.

Digitally signed by RAHUL

BOQ THIRD FLOOR DSR ITEMS

Providing and fixing false ceiling at all height including providing and fixing of frame work made of

special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm

(both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick

with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with

dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle

hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of

angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm

centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered

flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction

perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm

long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having

flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl

plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of

gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25

mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the

board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3

layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as

per manufacturer's specification and also including the cost of making openings for light fittings, grills,

diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings,

specification and direction of the Engineer in Charge but excluding the cost of painting with :

Digitally signed by RAHUL

BOQ THIRD FLOOR DSR ITEMS

12.45.3 12.5 mm thick tapered edge gypsum moisture resistant board 68.41 sqm 1300.5 88,967.21

METAL AND GLASS WORK

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built

up standard tubular sections/ appropriate Z sections and other sections of approved make conforming

to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up

the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.

26 21.1 Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever

required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless

steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.

(Glazing, paneling and dash fasteners to be paid for separately) : Kg

21.1.1 For Fixed Portion

21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron)

Weight of member 1 : Hindalco Section 22737 @ 2.594 kg/m

Weight of member 3 : Hindalco Section 22729 @ 0.441 kg/m

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making

27 21.1.2 provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket

required (Fittings shall be paid for separately)

Powder coated aluminium (minimum

thickness of powder coating 50 micron) Black Matt Finish

Providing and fixing glazing in aluminium door, window, ventilator

shutters and partitions etc. with EPDM rubber / neoprene gasket

28 21.3 etc. complete as per the architectural drawings and the directions of

engineer-in-charge . (Cost of aluminium snap beading shall be paid

in basic item):

28.1 21.3.2 With float glass panes of5mm thickness 12.00 sqm 1325.55 15,906.60

Filling the gap in between aluminium frame & adjacent RCC/ Brick/

Stone work by providing weather silicon sealant over backer rod of

approved quality as per architectural drawings and direction of

Engineer-in-charge complete.

29.1 21.8.1 Upto 5mm Depth and 5mm width 64.00 metre 85.25 5,456.00

DOORS and WINDOWS

Digitally signed by RAHUL

BOQ THIRD FLOOR DSR ITEMS

Providing and fixing 12mm thick frameless toughened glass

door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot &

30 21.18 double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing 3.00 sqm 4540.70 13,622.10

required door fittings, all complete as per direction of Engineer in charge (Door handle, lock and

stopper etc. to be paid separately)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type,

core of block board construction with

31 9.20 frame of 1st class hard wood and well matched teak 3 ply veneering

with vertical grains or cross bands and face veneers on both faces of shutters.

Opening - 4'x7.25'

35 mm thick including ISI marked Stainless Steel butt hinges

with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm

32 9.23 minimum depth on all edges of flush door shutters (over all area of door 3.24 Sqm 401.40 1,300.54

shutter to be measured).

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush

33 9.24 doors (cost of glass excluded) (overall area of door shutter to be

33.1 9.24.1 Rectangular or square 2.70 Sqm 173.95 469.67

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid

door/window/clerestory windows & desertory other Frames/Chowkhat comprising of virgin PVC

polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/

rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated

with miter joints after applying PVC solvent cement and screwed with full body threaded star headed

SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face)

& 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and

resistance to spread of flame of Class A category with property of being termite/borer proof,

water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash

fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold

fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames,

minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in

profile dimensions on plus side shall be acceptable but no extra payment on this account shall be

Opening - 4'x7.25'

Digitally signed by RAHUL

BOQ THIRD FLOOR DSR ITEMS

Providing and fixing carbon steel galvanised ( minimum coating 5 micron)

dash fastener of 10 mm dia double threaded 6.8 grade (yield strength

480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide

35 10.27 PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry,

etc. as per direction of Engineer-in-charge.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built

up standard tubular seCtions/ appropriate Z sections and other sections of approved make conforming

to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up

the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.

Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever

required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless

steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.

(Glazing, paneling and dash fasteners to be paid for separately) :

21.1.1 For Fixed Portion

36.1 21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) Black Colour 50 kg 466.30 23,315.00

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making

37 21.1.2 provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket -

required (Fittings shall be paid for separately)

37.1 21.1.2.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) 20 kg 564.8 11,296.00

Providing and fixing stainless steel (SS 304 grade) adjustable friction

windows stays of approved quality with necessary stainless steel

screws etc. to the side hung windows as per direction of Engineerin-

charge complete.

Providing and fixing aluminium tubular handle bar 32 mm outer dia,3.0 mm thick & 2100 mm long

with SS screws etc .complete as per direction of Engineer-in-Charge.

Powder coated minimum thickness 50 micron aluminium

tubular handle bar

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the

surface even and smooth complete.

Digitally signed by RAHUL

BOQ THIRD FLOOR DSR ITEMS

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic

41 13.60 Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying

additional coats wherever required to achieve even shade and colour.

41.1 13.60.1 Two or more coats on new work 272.27 sqm 137.85 37,531.73

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile

Organic Compound ) content.

With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Painting with synthetic enamel paint of approved brand and

manufacture to give an even shade :

43.1 13.61.1 Two or more coats on new work 2 Sqm 131.45 262.90

TOTAL CIVIL WORKS 6,88,075.57

BILL OF QUANTITY FOR ELECTRICAL WORKS-DSR

Point Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, with

modular switch, modular plate, suitable GI box and earthing the point with 1.5 Sqmm FRLS PVC

insulated copper conductor single core cable etc as required.

Wiring for twin control point with 1.5 sq.mm FRLS VC insulated copper conductor single core cable in

surface/ recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box

and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as

Wiring for light/power plug with 2X4 sqmm FRLS PVC insulated copper conductor single core cable in

3 1.12 surface/recessed medium class PVC conduit along with 1 No. 4 Sqmm FRLS PVC insulated copper 200.00 Meter 334.00 66,800.00

conductor single core cable for loop earthing as required.

Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated

4 1.14 copper conductor, single core cable in surface/recessed medium class PVC conduit as required

Rewiring for light point/fan point/ exhaust fan point/ call bell point with 1.5sqmm FRLS PVC insulated

copper conductor single core cable and 1.5 sqmm FRLS PVC insulated copper conductor single core

cable as earth wire in exisiting surface/recesssed steel/pvc conduit including dismantling as required.

Digitally signed by RAHUL

BOQ THIRD FLOOR DSR ITEMS

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in

6 1.21 surface/recess including cutting the wall and making good the same in case of recessed conduit as

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess,

7 1.32 including providing and fixing 6 pin 5/6 & 15/16. A modular socket outlet and 15/16 a modular switch, 20.00 Each 586.00 11,720.00

sonnections etc as required.

8 1.38 Supplying and fixing call bell/buzzer suitable for single phase 230V complete as required 3.00 Each 99.00 297.00

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with

Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2

nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value

(CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-

9 1.45 2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining 9.00 each 2730.00 24,570.00

accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation

resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc.

complete as required.

Installation of exhaust fan in the existing opening including making good the damage connetcion

testing commisssioning etc as required.

11 1.51 Extra for fixing the louvers/shutters complete with frame for a aexhaust fan of all sizes 1.00 each 207.00 207.00

Wiring for group controlled (looped ) light point/fan point/ exhaust fan point/ call bell point(without

independent switch etc) with 1.5 sqmm FRLS PVC insulated copper conductor single core cable in

surface/recessed PVC conduit and earthing the porint with 1.5 sqmm FRLS PVC insulated copper

conductor single core cable etc as required.

Digitally signed by RAHUL

BOQ THIRD FLOOR NDSR ITEMS

Renovation of Office of Public Enterprises Selection Board ( PESB) at Block No: 14, CGO Complex, Lodhi Road New Delhi

BILL OF QUANTITY FOR CIVIL WORKS-NDSR BASED ITEMS - 3rd Floor

IMAGE REFEERENCE

ONLY(DESIGN/IMAGE/FINISH

S No Description Quantity Unit Rate Amount MAY BE CHANGE DURING

EXUTION AS APPROVED BY

Demolishing/Dismantling of brick work, Partition Wall, cement

concrete,wooden boardings, tile work in floors/wall laid in cement mortar,

doors, windows and clerestory windows (steel or wood) shutter including

chowkhats, architrave, holdfasts etc , W.C. Pan of all sizes, Dismantling of all

dia G.I./ PVC pipe, MS/ Alluminium Framing, Electrical Conduits including

accessories (MS/PVC), GI Boxes, Distribution Box, Existing wire/Cable,

Fitting Fixtures, furnitures etc complete as direction by Engineer-In

charge.The item includes the disposal of moorum/building rubbish/ malba/

similar unserviceable, dismantled or waste material by mechanical transport

including loading, transporting, unloading to approved municipal dumping

ground for all lifts. Necessary permission/fee from statuary authority will be

arrange/bear by the contractor.

PLUMBING FIXTURES IMAGE REFEERENCE

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single

hole basin mixer of approved quality and make, including painting of fittings

and brackets, cutting and making good the walls wherever required:-

Size : 565x425x140 mm

Code - KUS-WHT-35935

Company - Jaquar

Health Faucet ALD CHR 565, 1 m Easy Flex Tube and Hooks, Polished, Plastic,

3 NS Chrome Finish 1.00 Nos 1144.99 1,144.99

Company - Jaquar

Digitally signed by RAHUL

BOQ THIRD FLOOR NDSR ITEMS

Providing and fixing wash basin sensor faucet in chrome finish battery

Code:-SNR-CHR-51011N

Providing and fixing Bowl With Cistern For Coupled WC With UF Soft Close

5 NS Slim Seat Cover, Hinges, Dual Flush Cistern Fitting And Fixing Accessories, 1.00 Nos 17566.16 17,566.16

Size: 365x630x750 mm, P Trap-180 mm

Providing and fixing washroom vanity in waterproof ply as per design.

Including oval mirror 600X900mm

Providing and fixing Bolt touch-free infrared hand dryer with 1150W rated

power & carbon brush motor , HDR-SSF-AK2803D

8 NS Providing and fixing court hook,ACN-CHR-1161N 2 Each 483.66 967.32

Providing and supplying Automatic Soap Dispensers, Capacity : 0.8L,

Material: Aluminium/ABS, Finish : Chrome/Black, SDR-BLC-DJ0160AS

Digitally signed by RAHUL

BOQ THIRD FLOOR NDSR ITEMS

Providing and fixing Stainless Steel Pedal Dustbin with Lid & Removable

Trashcan- &Litre capacity

Providing and fixing CP, brass grating of apporved quality and make

conforming to IS:Specification

Providing and fixing AC 4 Class wooden laminated flooring as per company

standards. Wear resistant interlocking planks size 190 x 1200 with surface

layer consisting of a Aluminum Oxide coated tissue to make the flooring

13 NS surface resistant to impact, scratches, burns & stains. Melamine

impregnated decorative wooden texture paper layer on top of wax coated

water resistant 8mm HDF base and balancing paper base. 2.5" PVC skirting

and reducer complete as per directions of Engineer in charge.

Supply of AC4 Laminated wooden flooring. Shade Authentic Oak (L0701-

1462), Size 1200mm x 190mm x 8mm

Providing and fixing, in position concealed G.I. section for wall paneling

using board of required thickness fixed on the 'W' profile (0.55 mm thick)

having a knurled web of 51.55 mm and two flanges of 26 mm each with lips

of 10.55 mm, placed @ 610 mm C/C in perimeter channel having one flange

of 20 mm and another flange of 30 mm with thickness of 0.55 mm and web

15 NS of length 27 mm. Perimeter channel is fixed on the floor and the ceiling with

the nylon sleeves @ 610 mm C/C with fully threaded self-tapping dry wall

screws. Board is fixed to the 'W' profile with 25 mm countersunk ribbed

head screws @ 200 mm C/C., all complete as per the drawing & directions of

engineer-in-charge.

12mm plyboard of MR grade and termite resistant with 4mm Veener

Digitally signed by RAHUL

BOQ THIRD FLOOR NDSR ITEMS

Supply & fixing of wall paneling of slats surco high density fiberboard made

out of pure pinewood particles , Fire Resistance - Pink in colour core with

5 test Fire Resistance BS 476 part 5 , BS 476 part 6 , BS 476 part 7 ISO 1182

ASTM E662 Smoke Density - Melamine laminated finish, perforated wooden

grooved HDF slats L16-2 (2 mm grooves @ 8 mm centers),tongue-groove

edge for a seamless look of lineal dimension size 128 mm x 2440 mm x 16

mm thick having density 700 Kg /m3, weight -9 Kgs/m2 with back fleecs

from soundtex Germany nonwoven acoustic to be pasted on slats surco is to

be installed by using GI strut system. The technical parameters are as

follows Core Variants - Fiberboard, Climate (OC RH) – 50, 70 Light

17 NS reflectance – 75%,Green (RC %) – 25, Hygiene (VoC, Clean room) – Low, 30.00 Sqm 6354.14 1,90,624.20

Class 1,Strength, Load capacity (Kg) - Anti sag, Ball-Impact. The concealed

wall paneling system shall include GI Wall channel (WC25) having thickness

0.45mm, length 3600mm, unequal flanges of 15 & 20mm and web of 25mm

should be fixed along the perimeters of the wall with nylon sleeves and

suitable fasteners at every 300mm centers. Then fixed Main channels

(MC45) having thickness 0.9mm, length 3600mm, equal flanges of 15mm

and web 45mm from the side wall & fixed at every 1200mm centers with GI

cross channel(CC25) having thickness 0.45mm, length 3600mm, knurled web

35mm, depth of 25mm and equal flanges 9.5mm is fastened to the Main

channel in the direction perpendicular to the Main Channel at every 600mm

centers. The framework will maintain 50 / 75 mm gap from the walls. Now

Providing and fixing Canvas painting of Minimum Size 6ftX3ft with suitable

18 NS design as approved by the Engineer In Charge 4 Nos. 9438.68 37,754.72

Providing ceramic planter pots of minimum size of 400mm height with

19 NS desired plants as approved by the Engineer In charge. 5 Nos. 3701.45 18,507.25

METAL AND GLASS WORK

Providing and fixing Linear glass door handle in S.S 304 (32x600mm) in black

21 NS Providing and fixing Brass mortice lock, chrome plated. (Company - Godrej) 3.00 Nos 2714.40 8,143.20

Digitally signed by RAHUL

BOQ THIRD FLOOR NDSR ITEMS

Providing and fixing SS door lock- OSDL-11L-K2N STD SSS. Ozone Make.

Overall Dimensions:-170 (L) X 70mm ( H)

Glass Thickness 8-12mm.

Lock with Europen Cylinder.

22 NS Directions:-Left Closing/Right opening, if fixed glass on other side. Material:- 1.00 Nos. 2714.40 2,714.40

Stainless Steel.

Finish:-BRUSHED NICKEL PLATED.

CYLINDER & STRIKE PLATE included, Cylinder:-OSL-LKH- ACC-K2N-L 42.8mm

Providing and fixing 8mm toughened clear glass in aluminium section used

for partition. Make:- Saint Gobin

Providing and fixing Bharat Haat, Kalarambh Brass Ashok Stambh Wall

Hanging Emblem Sculpture Medium YellowMounting Type Wall Mount

24 NS Finish Type Brass

Special Feature Waterproof

Included Components 1 Brass wall Hanging Ashok Stmbh

Providing & fixing of Roller Blinds as per the approved sample with fabric

made up of 28% Polyesterand 68% PVC 4% alumlnlum layer on the back,

l2Stex Tilter Basket weave of thickness O.S3mm tS% (ISO 2286-2) and

wleghing 407gsmt5% with openess factor of 5% .The tear resistance (Warp

172Nt10% & ,Weft 153NH0%) As per ISO 544674, and pass NFPA 701 Fire

Resistance test, Vista Blinds

providing and fixing Brass lettering name plate with appropiate size over

Backplate as approved by the engineer in charge

Moulding work in plaster of paris for chair person's room of appropriate size

and design of mould as per 3D views.

Readymade wooden moulding work with for chair person's room of

appropriate size and design as per 3D views.

30 NS Providng and applying frosted glass film. 3.00 Sqm 863.67 2,591.01

Digitally signed by RAHUL

BOQ FURNITURE THIRD FLOOR

Renovation of Office of Public Enterprises Selection Board ( PESB) at Block No: 14, CGO Complex, Lodhi Road New Delhi

BILL OF QUANTITY FOR FURNITURE (NDSR)- 3RD FLOOR

S no Location Description Unit Rate Amount

BILL OF QUANTITY FOR FURNITURE-3RD FLOOR

PS Rooms Desk Providing in place of main table with overall size of table equal to 1350 x 600 x750mm. The table is made of 25 mm 2 Nos 19999.70 39,999.40

Size - 4'6" x 2' thick Prelaminated Twin Board of E1-P2 grade edge banded with matching 2mm thick PVC lipping. Grommet

provided on work surface for wire manaement. The modesty panel is made of 25 mm thick Prelaminated Twin Board

of E1-P2 grade. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved

shade edge banded with matching 2 mm thick PVC lipping. The HInge door unit is made of 25 mm thick Pre-

1 NS laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping.

Handles are provided for ease of opening. Pedestals are provided with lock for security. The product must be UL

Greenguard certified.

Conference room work Providing in place of main table with overall size of table equal to 1350 x 600 x750mm. The table is made of 25 mm 1 Nos 19999.70 19,999.70

station thick Prelaminated Twin Board of E1-P2 grade edge banded with matching 2mm thick PVC lipping. Grommet

Size - 4'6" x 2' provided on work surface for wire manaement. The modesty panel is made of 25 mm thick Prelaminated Twin Board

of E1-P2 grade. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved

shade edge banded with matching 2 mm thick PVC lipping. The HInge door unit is made of 25 mm thick Pre-

2 NS laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping.

Handles are provided for ease of opening. Pedestals are provided with lock for security. The product must be UL

Greenguard certified.

Digitally signed by RAHUL

BOQ FURNITURE THIRD FLOOR

3 NS Workstation Chairs The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method 2 Nos 7636.70 15,273.40

described in OCP-QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane

foam. The dimensions of seat shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated

(DFT 40-60 microns) tubular frame of dia 2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured

lumbar support for extra comfort. The back shall be upholstered using Net fabric with high tenacity yarn. The

dimensions of back shall be 46.5 cm (W) x 70.5 cm (H). The HR polyurethane foam shall be moulded with density

=45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The one-piece armrests shall be

injection moulded from black Co-polymer Polypropylene. The mechanism shall be designed with 360° revolving type,

17±2° maximum tilt m pivot at centre, Upright position locking., Tilt tension adjustment. The pneumatic height

adjustment shall has an adjustment stroke of 11.0 ±0.3cm. The bellow shall be 3 piece telescopic type and injection

moulded in Black Polypropylene. The pedestal shall be injection moulded in black 33% glass-filled Nylon66 and fitted

with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). The twin

wheel castors shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 43.3

to max 54.3cm, Height - min99.5 to max 110.5cm, Width & Depth of Chair as measured from pedestal - Width-76.3

cm and Depth-76.3 cm.

4 NS Visitor's Chairs The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method 12 Nos 5730.30 68,763.60

described in OCP-QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane

foam. The dimensions of seat shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated

(DFT 40-60 microns) tubular frame of dia 2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured

lumbar support for extra comfort. The back shall be upholstered using Net fabric with high tenacity yarn. The

dimensions of back shall be 46.5 cm (W) x 60.5 cm (H). The HR polyurethane foam shall be moulded with density

=45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The one-piece armrests shall be

injection moulded from black Co-polymer Polypropylene. The powder coated (DFT 40-60 microns) tubular frame

shall be cantilever type & made of dia 2.54±0.03cm x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. Overall Dimensions of

Chair shall be Seat Height - 46.5cm, Height - 93.5cm, Width & Depth of Chair as measured from pedestal -Width-61.0

cm and Depth-64.5 cm.

5 NS Low Height Cabinet Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal cladding of 3 Nos 16335.80 49,007.40

Size - 2'6" x 2' 0.8mm thk C.R.C.A (as per IS: 513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50±10

microns thickness.In case of 2.5feet Height Storage units, wooden top is provided which is made of 25mm thick Pre-

laminated board whereas 4.0feet and 4.5feet height Storage units are provided with 1 Imm thk bent metal tops

made of 0.8mm thk C.R.C.A (as per IS: 513). The metal tops are coated with Epoxy polyester powder of 50±10

microns thickness.

Digitally signed by RAHUL

BOQ FURNITURE THIRD FLOOR

6 NS 3 Seater Sofa Set Supplying and Placing in place of 3 seater sofa. The overall dimensions of the sofa shall be 2060W x 905D x 855H. 1 Nos 36825.20 36,825.20

The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU

foam with Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back

should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of

density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be made up of 1.2±0.1 cm.

thick hot pressed plywood (which also shall be resistance and termite proof as per IS:303.) and pinewood of cross

section deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted

over understrucrure for cushioning effect. It should be a welded assembly made in Stainless steel (grade SS 202)

tube & plate with plastic endcap

Digitally signed by RAHUL

BOQ FURNITURE THIRD FLOOR

7 NS Storage Cabinet Aesthetically appealing completely knock down construction.The add—on units are stack widthwise to form a row of 1 Nos 40000.40 40,000.40

SIze - 10' x 2'6" storage having a common side panel. (Note— Single Main unit should not be offered.Minimum 1 Main + IAddon to

be offered)Legs fitted with screw typeleveler(add 45mm to the height).Made from combination of CRCA** 0.5 mm &

0.8mm Thickness.CRCA 'D' Grade as per IS-513.

Supplying & Placing conference table in completely knock down conditions with an

overall size 13600mm X 1800mm X 750mm that is to be assembled at site. The

worktop shall be made up of back to back 36mm thick Pre-laminated particle board of

grade II of IS 12823 with approved laminate and finish as per approved shade. The

table top profile shall be in rectangle shape and the edges shall be sealed with 2mm

thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly

pasted with the assistance of edge banding machine at 200 degree Celsius. Flapper

box shall be enclosed at table top. Wire carrier shall be provided below the table top

for power connection made up of 0.8mm thick high yield strength CRCA sheet of grade

'D' confirming to IS:513. The table top shall be supported on MS powder coated

rectangle pipe having cross-section area 40mm X 20mm with 1.6mm thick. The table

shall be clad with 18mm thick modesty panel which provide structural support for the

8 NS 10 seater Board Table table. It should be 18mm thick pre-laminated particle board with appropriate PVC edge 1.00 Nos 422321.4 422321.4

banding connected with both end. The table understructure shall have SS 202 grade

pipe frame leg having cross-section area 80mm X 20mm. Bottom tile shall be situated

in between the leg with fabric. There shall be buffers provided at the base to avoid

scratches on the floor. The table connections have to be made in such a way that no

gap should be seen in between. The manufacturer shall have quality and safety

assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA

membership and AIOTA certification. The board used should meet International

Standard of quality, Indian Standard IS 12823 grade II should meet long time load

bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity

bending tested as per IS 2380. The product should be approved make The product

should be approved make as per Engineer-Incharge.

Providing and Placing High Back Chair with overall size of 76.1 cm W x 76.1 cm D x 112.7 – 130.2 cm H x 43.1 – 53.1 cm Seat Height. The

seat is cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with leatherette and molded high

resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W

cm x 48.0 D cm. The back is cushioned made of PU foam with insitu molded M.S. ERW round tube of size 1.9±0.03cm x 0.16±0.0128cm,

upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The armrest top is molded from polyurethane and mounted on to a

drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome plated finish.

The armrest is height adjustable up to 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism is designed with following features : 360°

9 NS Board room chairs revolving type, front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort, tilt tension 12.00 Nos 19079.85 228958.2

adjustment can be operated in seating position, 5-position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio

1:2, The mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment is integrated in the seat

through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm. Back frame is connected to the up/down mechanism in

plastic T spine. It can be adjusted in the range of 7.42±0.5 comfort the comfortable back support to suit individual need. The pneumatic

height adjustment has an adjustment stroke of 10.0±0.3cm. The pedestal is high pressure die cast polished aluminium & fitted with 5 nos.

of twin wheel castors. The pedestal is 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection

molded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal.

Digitally signed by RAHUL

BOQ FURNITURE THIRD FLOOR

### NS Full Height Cabinet Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal cladding of 1 Nos 149725.70 1,49,725.70

Size - 11' x 8' 0.8mm thk C.R.C.A (as per IS: 513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50±10

microns thickness.In case of 2.5feet Height Storage units, wooden top is provided which is made of 25mm thick Pre-

laminated board whereas 4.0feet and 4.5feet height Storage units are provided with 1 Imm thk bent metal tops

made of 0.8mm thk C.R.C.A (as per IS: 513). The metal tops are coated with Epoxy polyester powder of 50±10

microns thickness

Digitally signed by RAHUL

BOQ FURNITURE THIRD FLOOR

11 NS 2 Seater Sofa Set Providing and placing in position of 2 seater sofa. The overall dimensions of the sofa shall be 1460W x 905D x 855H. 3 Nos 27073.62 81,220.86

The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU

foam with Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back

should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of

density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be made up of 1.2±0.1 cm.

thick hot pressed plywood (which also shall be resistance and termite proof as per IS:303.) and pinewood of cross

section deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted

over understrucrure for cushioning effect. It should be a welded assembly made in Stainless steel (grade SS 202)

tube & plate with plastic endcap.

12 NS Coffee Table Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing 2 Nos 11693.50 23,387.00

Size - 4'x 2' with understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall

dimensions of table shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.

13 NS Book shelf (154cm x 46 cm) Providing and placing book shelf in real wood (Teak, Sheesham) finished with malemine polish as approved by the 2 Nos 14077.00 28,154.00

engineer in charge

TOTAL FURNITURE BOQ 12,03,636.26

Digitally signed by RAHUL

SUMMARY 5TH FLOOR PESB

Renovation of Office of Public Enterprises Selection Board ( PESB) at Block

No: 14, CGO Complex, Lodhi Road New Delhi

SUMMARY OF COST OF FIFTH FLOOR

S.No. Item Description Amount (DSR) Amount (NS)

2 Electro-Mechanical Works 9,84,138.00 1176774.86

4 Furniture 35,93,166.95

Digitally signed by RAHUL

BOQ CIVIL DSR-PESB

Renovation of Office of Public Enterprises Selection Board ( PESB) at Block No: 14, CGO Complex, Lodhi Road New Delhi

BILL OF QUANTITY FOR CIVIL WORKS-DSR ITEM FOR 5TH FLOOR

S No DSR 2021 Description Quantity Unit Rate Amount

Cutting holes of required size in brick masonry wall for fixing of exhaust

fan including providing and fixing 300 mm dia PVC pipe conforming

BIS-12818 and making good the same etc. complete as per direction

of Engineer-in-charge.

Hacking of CC flooring including cleaning for surface etc. complete

as per direction of the Engineer-in-Charge.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in

3 14.1 proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish

to the dumping ground, all complete as per direction of Engineer-in-Charge.

3.1 14.1.2 With Cement mortar 1:4 (1 cement:4 coarse sand) 41.08 Sqm 478.00 19,636.24

Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to IS: 2222 in

superstructure above

plinth level up to floor five level in cement mortar 1:6 (1 cement : 6

4.1 6.3.1 With FPS (Non Modular) Bricks 5 Cum 8030.6 40,153.00

Half brick masonry with common burnt clay F.P.S. (non modular) bricks

5 6.13 of class designation 7.5 in superstructure above plinth level up to floor

5.1 6.13.1 Cement mortar 1:3 (1 cement :3 coarse sand) 64.3 Sqm 1043.1 67,071.33

6 13.4 12mm Cement plaster

Providing and laying cement concrete in retaining walls, return walls,

walls (any thickness) including attached pilasters, columns, piers,

abutments, pillars, posts, struts, buttresses, string or lacing courses,

parapets, coping, bed blocks, anchor blocks, plain window sills, fillets,

sunken floor etc., up to floor five level, excluding the cost of centering,

shuttering and finishing:

1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural

7.1 sources : 4 graded stone aggregate 20 mm nominal size 1.2 Cum 9375.2 11,250.24

derived from natural sources)

Digitally signed by RAHUL

BOQ CIVIL DSR-PESB

Centering and shuttering including strutting, propping etc. and removal

Lintels, beams, plinth beams, girders, bressumers and

Providing and laying in position ready mixed or site batched

design mix cement concrete for reinforced cement concrete work;

using coarse aggregate and fine aggregate derived from natural

sources, Portland Pozzolana / Ordinary Portland /Portland Slag

cement, admixtures in recommended proportions as per IS: 9103

to accelerate / retard setting of concrete, to improve durability

and workability without impairing strength; including pumping

of concrete to site of laying, curing, carriage for all leads; but

9 5.33 excluding the cost of centering, shuttering, finishing and

reinforcement as per direction of the engineer-in-charge; for the

following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement

content in design mix shall be payable separately. In case the

cement content in design mix is more than 1.10 times of the

specified minimum cement content, the contractor shall have

discretion to either re-design the mix or bear the cost of extra

Concrete of M25 grade with minimum cement

content of 330 kg /cum

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete

above plinth level.

10.1 2.55A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. 200 kg 89.65 17,930.00

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply,

including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of

11 18.8 pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including

testing of joints complete as per direction of Engineer in Charge.

Concealed work, including cutting chases and making good the walls etc.

11.1 18.8.2 20 mm nominal pipes 50 meter 513.75 25,687.50

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing

with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

Digitally signed by RAHUL

BOQ CIVIL DSR-PESB

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water

13 12.42 pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for

thermal expansion.

12.42.1 Coupler

12.42.4 Single Tee without Door

12.42.5 Bend 87.5 degree

12.42.6 Shoe(Plain)

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40

14 17.10 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

17.10.2 Kitchen Sink without Drain Board

15 17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

17.28.1 Semi Rigid Pipe

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than

17.1 18.50.1 15mm Nominal Bore

Digitally signed by RAHUL

BOQ CIVIL DSR-PESB

18 18.53 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893

Providing and fixing PTMT Waste Coupling for wash basin and sink,

of approved quality and colour

19.1 17.69.1 Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms 3.00 each 103.00 309.00

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed

20 17.73 fittings

arrangement of approved quality and colour.

600 mm long towel rail with total length of 645 mm, width

20.1 17.73.2 78 mm and effective height of 88 mm, weighing not less 3.00 Each 600.35 1,801.05

21 17.34 Providing and fixing toilet paper holder :

WATERPROOFING WORK

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed

with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with

22 22.5 water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of 25.00 sqm 516.60 12,915.00

slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed

to air cure for 4 hours followed with water curing for 48 hours.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen

platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid

over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching

pigment, epoxy touch ups, including rubbing, curing,moulding and polishing to edges to give high gloss finish etc. complete

Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble

Digitally signed by RAHUL

BOQ CIVIL DSR-PESB

Providing and fixing 18 mm thick gang saw cut, mirror polished,premoulded and prepolished, machine cut for kitchen

platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid

over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching

pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete

Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble

Providing and fixing 18 mm thick gang saw cut, mirror polished,

premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of

required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand),

joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and

polishing to edges to give high gloss finish etc. complete at all levels.

Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give

high gloss finish etc. complete as per design approved by Engineer-in-Charge.Marble work

Extra for providing opening of required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and

26 8.50 similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and 1.00 Nos 808.15 808.15

polishing of cut edges etc.complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the

manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by

Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse

27 8.31 sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of

matching shade complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water

absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on

20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting

28 11.41A the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only .

Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet

for placing the tiles gently and easily.

Double charge vitrified tile polished finish of size

Size of Tile 800 x 800 mm

Digitally signed by RAHUL

BOQ CIVIL DSR-PESB

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less

than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm

29 11.46.3 thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting 37.00 sqm 1932.75 71,511.75

the joint with white cement & matching pigments etc. complete.

Size of Tile 800X800 mm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water

absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on

20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting

the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only .

Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet

for placing the tiles gently and easily.

11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of

31 11.48 desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per

direction of Engineer-in-charge.

32 5.9.17 Cornices and mouldings 1.00 sqm 769.30 769.30

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing

of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side

inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the

floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or

suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other

flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at

a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed

33 9.105 flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing

of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels

at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid

through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the

horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and

finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5

mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in

charge all complete. 9.105.1 75 mm overall thickness partition with 12.5 mm thick double

Digitally signed by RAHUL

BOQ CIVIL DSR-PESB

75mm overall thickness partition with 12.5 mm thick double

33.1 9.105.2 skin tapered edged plain Gypsum plaster board conforming 22.00 Sqm 1530.05 33,661.10

to IS: 2095: (part I): 2011 (Board with BIS certification marks)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power

pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting

of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange

fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle

hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with

intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section

0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to

centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm

34 12.45 dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of

20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with

25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel

with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered

and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3

layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's

specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of

perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but

excluding the cost of painting with :

12.5 mm thick tapered edge gypsum moisture resistant

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter

locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of

main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick

(minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30

mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600

mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be

35 12.52 interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and

laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services

like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI

slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI

adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main

T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for

all heights as per specifications, drawings and as directed by Engineer-in-charge.

Digitally signed by RAHUL

BOQ CIVIL DSR-PESB

12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard,

manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant

36 12.54.3 PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed withthe face side PVC film 41.00 sqm 1948.95 79,906.95

which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make

the tile a completely sealed unit.

Metal & Glass Work

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular

seCtions/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash

fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with

38 21.1 required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed

mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless

steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash

fasteners to be paid for separately) :

21.1.1 For Fixed Portion

21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) Black Colour

Weight of member 1 : Hindalco Section 22737 @ 2.594 kg/m

Weight of member 2 : Hindalco Section 22731 @ 0.527 kg/m

Weight of member 3 : Hindalco Section 22729 @ 0.441 kg/m

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of

39 21.1.2 fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for

Powder coated aluminium (minimum

thickness of powder coating 50 micron)

Filling the gap in between aluminium frame & adjacent RCC/ Brick/

Stone work by providing weather silicon sealant over backer rod of

approved quality as per architectural drawings and direction of

Engineer-in-charge complete.

40.1 21.8.1 Upto 5mm Depth and 5mm width 38.40 metre 85.25 3,273.60

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene

42 21.3.2 gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap 321.00 sqm 1325.55 4,25,501.55

beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 20 kg/sqm)

Digitally signed by RAHUL

BOQ CIVIL DSR-PESB

Digitally signed by RAHUL

BOQ CIVIL DSR-PESB

Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including

providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making

necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer in charge (Door handle, lock

and stopper etc. to be paid separately)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board

construction with frame of 1st class hard wood and well matched teak 3 ply veneering

with vertical grains or cross bands and face veneers on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges

with necessary screws

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on

unexposed surface etc. complete :

9.40.1 2nd class teak wood

Providing and fixing PTMT Butt hinges with necessary screws etc.

75x60x10 mm fitted with 5.5 mm dia M.S. Bright Bar Rod

weighing not less than 34 gms

Providing and fixing PTMT Tower Bolts with 12 mm one piece rod inside

and necessary screws etc., complete.

46.1 9.108.1 152x42x18 mm weighing not less than 60 gms 15.00 each 58.85 882.75

Providing and fixing chromium plated brass handles with necessary

screws etc. complete:

Providing and fixing 2nd class teak wood lipping/ moulded beading or taj

beading of size 18X5 mm fixed with wooden adhesive of approved quality

and screws/nails on the edges of the Pre-laminated particle board as

per direction of Engineer-in-charge.

Digitally signed by RAHUL

BOQ CIVIL DSR-PESB

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/clerestory windows

& desertory other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium

carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12

for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star

headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N

49 26.86 (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of

Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position

with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S

hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm

tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall

be acceptable but no extra payment on this account shall be made.

Opening - 4'x7.25'

Painting with synthetic enamel paint of approved brand and

manufacture to give an even shade :

50.1 13.61.1 Two or more coats on new work 10 Sqm 131.45 1,314.50

Providing and fixing carbon steel galvanised ( minimum coating 5 micron)

dash fastener of 10 mm dia double threaded 6.8 grade (yield strength

51 10.27 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide

PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry,

etc. as per direction of Engineer-in-charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in

52 9.1.2 position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for 0.50 cum 106720.85 53,360.43

separately). Sal wood

Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit

shutter thickness complete

Digitally signed by RAHUL

BOQ CIVIL DSR-PESB

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular

seCtions/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash

fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with

54 21.1 required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed

mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless

steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash

fasteners to be paid for separately) :

21.1.1 For Fixed Portion

54.1 21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) Black Colour 150 kg 466.30 69,945.00

Providing and fixing factory made uPVC white colour sliding glazed door

comprising of uPVC multi-chambered frame with in-built roller track and

sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized

mild steel section made from roll forming process of required length

(shape & size according to uPVC profile), appropriate dimension uPVC

extruded glazing beads, uPVC extruded interlock and uPVC extruded

Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy

(white powder coated) handle with key on one side of extreme panels

along with zinc plated mild steel multi point locking having transmission

gear with keeps, zinc alloy (white powder coated) cresent lock (if

55 9.147f required), stainless steel (SS 304 grade) body with adjustable double

nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x

8 mm size for fixing frame to finished wall and necessary stainless

steel screws etc. Profile of frame & sash shall be mitred cut and fusion

welded at all corners, including drilling of holes for fixing hardware's and

drainage of water etc. After fixing frame the gap between frame and

adjacent finished wall shall be filled with weather proof silicon sealent

over backer rod of required size and of approved quality, all complete as

per approved drawing & direction of Engineer-in-Charge. (Single / double

glass panes, wire mesh and silicon sealent shall be paid separately).

Variation in profile dimension in higher side shall be accepted but no

extra payment on this account shall be made.

Two track two panels sliding door made of (big series) frame

67 x 50 mm & sash 46 x 82 mm both having wall thickness

55.1 9.147f.1 of 2.3 ± 0.2 mm and single glazing bead / double glazing 5 Sqm 6882.4 34,412.00

bead of appropriate dimension. (Area of door above 2.00

sqm upto 5.00 sqm)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of

56 fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for

Digitally signed by RAHUL

BOQ CIVIL DSR-PESB

Powder coated aluminium (minimum

56.1 21.1.2.2 thickness of powder coating 50 micron) 50 kg 564.8 28,240.00

Providing and fixing stainless steel (SS 304 grade) adjustable friction

windows stays of approved quality with necessary stainless steel

screws etc. to the side hung windows as per direction of Engineerin-

charge complete.

Providing and fixing aluminium tubular handle bar 32 mm outer dia,3.0 mm thick & 2100 mm long with SS screws etc

.complete as per direction of Engineer-in-Charge.

Powder coated minimum thickness 50 micron aluminium

tubular handle bar

Applying priming coats with primer of approved brand and

manufacture, having low VOC (Volatile Organic Compound ) content.

With water thinnable cement primer on wall surface

having VOC content less than 50 grams/litre

60 13.6 Wall painting with acrylic emulsion paint of approved brand and manafacture to give an even shade:

60.1 13.6.1 Two or more coats on new work 800.00 sqm 137.85 1,10,280.00

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and

smooth complete.

TOTAL CIVIL WORKS-DSR ITEMS 34,94,606.96

Digitally signed by RAHUL

BOQ CIVIL DSR-PESB

BILL OF QUANTITY -ELECTRICAL WORKS DSR ITEMS

Point Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper

1 1.10 conductor single core cable in surface/ recessed medium class PVC conduit, with modular switch, modular plate, suitable GI

box and earthing the point with 1.5 Sqmm FRLS PVC insulated copper conductor single core cable etc as required.

Point Wiring for group controlled (looped) light point/fan point/exhaust fan point/call bell point (without independent

switch etc) with 1.5 sqmm FRLS PVC insulated copper conductor single core cable in surface/recessed PVC conduit and

earthing the point with 1.5 SQMM FRLS PVC insulated copper conductor single coe cable etc are required.

Wiring for twin control point with 1.5 sq.mm FRLS VC insulated copper conductor single core cable in surface/ recessed

3 1.11 medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS 5.00 point 1562.00 7,810.00

PVC insulated copper conductor single core cable etc. as required.

Wiring for light/power plug with 2X4 sqmm FRLS PVC insulated copper conductor single core cable in surface/recessed

medium class PVC conduit along with 1 No. 4 Sqmm FRLS PVC insulated copper conductor single core cable for loop earthing

Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor,

single core cable in surface/recessed medium class PVC conduit as required

5.3 1.14.3 2X4 Sqmm +1X4 Sqmm Earth wire 250.00 Meter 334.00 83,500.00

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting

the wall and making good the same in case of recessed conduit as required.

Supplying and fixing following modular switch/socket on the existing modular plate & switch box including connections but

excluding modular plate etc as required.

53.5 1.24.6 Telephone socket outlet 15.00 Each 148.00 2,220.00

Supplying and fixinf following sizes/modules, GI box along with modular base & cover plate for modular switches in recess

etc as required

Digitally signed by RAHUL

BOQ CIVIL DSR-PESB

55 1.28 Supplying and fixing following modular base and cover plate on existing modular metal boxes etx as required

56 1.38 Supplying and fixing call bell/buzzer suitable for single phase 230V complete as required 8.00 Each 99.00 792.00

Supplying and fixing following way horizontal type three pole and neutral sheet steel MCB distribution board 415 V on

56 2.4 surface/recess complete with tinned copper bus bar neutral bus bar earth bar din bar interconnections powder painted

including earthing etc as required. (but without MCB/RCCB/Isolator)

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct

Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope,

copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210

Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed

control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.),

insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as

Installation of exhaust fan in the existing opening including making good the damage connetcion testing commisssioning etc

59 1.51 Extra for fixing the louvers/shutters complete with frame for a aexhaust fan of all sizes 5.00 each 207.00 1,035.00

Wiring for group controlled (looped ) light point/fan point/ exhaust fan point/ call bell point(without independent switch

etc) with 1.5 sqmm FRLS PVC insulated copper conductor single core cable in surface/recessed PVC conduit and earthing the

porint with 1.5 sqmm FRLS PVC insulated copper conductor single core cable etc as required.

Supplying and fixing 5 amps. to 32 amps. rating, 240/415 V, 10kA, "C" curve, miniature circuit breaker (MCB) suitable for

61 2.10 inductive load of following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, 240V, isolator in the existing MCB DB complete with connections teesting

and commissioning etc as required.

Digitally signed by RAHUL

BOQ CIVIL DSR-PESB

Supplying and fixing following rating, double pole, (signle phase and neutral) 240v residual current circuit breaker (RCCB)

63 2.14 having a sensitivity current 30mA in the existing MCB DB complete with connections testing and commissioning etc as

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing

masonry open duct as required.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated

65 9.1 and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV

grade as required.

Digitally signed by RAHUL

BOQ CIVIL NDSR-PSEB

Renovation of Office of Public Enterprises Selection Board ( PESB) at Block No: 14, CGO Complex, Lodhi Road New Delhi

BILL OF QUANTITY FOR CIVIL WORKS-NDSR ITEM FOR 5TH FLOOR

IMAGE REFEERENCE

ONLY(DESIGN/IMAGE/FINISH

S No Description Quantity Unit Rate Amount MAY BE CHANGED DURING

EXUTION AS APPROVED BY

Demolishing/Dismantling of brick work, Partition Wall, cement

concrete,wooden boardings, tile work in floors/wall laid in cement mortar,

doors, windows and clerestory windows (steel or wood) shutter including

chowkhats, architrave, holdfasts etc , W.C. Pan of all sizes, Dismantling of all

dia G.I./ PVC pipe, MS/ Alluminium Framing, Electrical Conduits including

accessories (MS/PVC), GI Boxes, Distribution Box, Existing wire/Cable, Fitting

Fixtures, furnitures etc complete in all respect as direction by Engineer-In

charge.The item includes the disposal of moorum/building rubbish/ malba/

similar unserviceable, dismantled or waste material by mechanical transport

including loading, transporting, unloading to approved municipal dumping

ground for all lifts. Necessary permission/fee from statuary authority will be

arrange/bear by the contractor.

Health Faucet ALD CHR 565, 1 m Easy Flex Tube and Hooks, Polished, Plastic,

2 NS Chrome Finish 3.00 Nos 1144.99 3,434.97

Company - Jaquar

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single

hole basin mixer of approved quality and make, including painting of fittings

and brackets, cutting and making good the walls wherever required:-

Size : 565x425x140 mm

Code - KUS-WHT-35935

Company - Jaquar

Digitally signed by RAHUL

BOQ CIVIL NDSR-PSEB

Providing and fixing wash basin sensor faucet in chrome finish battery

Code:-SNR-CHR-51011N

Providing and fixing Single Lever Basin Mixer with Popup Waste and 450mm

Long Braided Hoses. LYR-CHR-38051B

Providing and fixing Bowl With Cistern For Coupled WC With UF Soft Close

6 NS Slim Seat Cover, Hinges, Dual Flush Cistern Fitting And Fixing Accessories, 3.00 Nos 17566.16 52,698.48

Size: 365x630x750 mm, P Trap-180 mm

Providing and fixing Bolt touch-free infrared hand dryer with 1150W rated

power & carbon brush motor , HDR-SSF-AK2803D

8 NS Providing and fixing court hook,ACN-CHR-1161N 5 Each 483.66 2,418.30

Digitally signed by RAHUL

BOQ CIVIL NDSR-PSEB

Providing and supplying Automatic Soap Dispensers, Capacity : 0.8L,

Material: Aluminium/ABS, Finish : Chrome/Black, SDR-BLC-DJ0160AS

Providing and fixing Stainless Steel Pedal Dustbin with Lid & Removable

Trashcan- &Litre capacity

Providing and fixing Urinal Without Sensor With Fixing Accessories, Size:

480x300x740 mm , URS-WHT-13255

Proviidng and fixing Sensor Mini Concealed Type Flushing Valve for Urinal

Complete Set with Installation Box (Battery Operated)

13 NS Providing and fixing Curved shaped urinal partition with frosted glass 1.00 each 4540.44 4,540.44

14 NS Providing pipe joint sealant using drip seal from jointing PVC to CI pipes 5.00 kg 333.13 1,665.65

Digitally signed by RAHUL

BOQ CIVIL NDSR-PSEB

providing and fixing Brass lettering name plate with appropiate size over

Backplate as approved by the engineer in charge no.s

Wooden plank type - Vitrified tiles. As per analysis

Providing and fixing, in position concealed G.I. section for wall paneling using

board of required thickness fixed on the 'W' profile (0.55 mm thick) having a

knurled web of 51.55 mm and two flanges of 26 mm each with lips of 10.55

mm, placed @ 610 mm C/C in perimeter channel having one flange of 20

mm and another flange of 30 mm with thickness of 0.55 mm and web of

17 NS length 27 mm. Perimeter channel is fixed on the floor and the ceiling with

the nylon sleeves @ 610 mm C/C with fully threaded self-tapping dry wall

screws. Board is fixed to the 'W' profile with 25 mm countersunk ribbed head

screws @ 200 mm C/C., all complete as per the drawing & directions of

engineer-in-charge.

12mm plyboard of MR grade and termite resistant with 1mm laminate in

matt/gloss finish

Toilet Cubicles made of 18mm thick compact laminate HPL Boards complete

with doors and SS accessories of MARINO make

Supply & fixing of wall paneling of slats surco high density fiberboard made out of pure

pinewood particles , Fire Resistance - Pink in colour core with 5 test Fire Resistance BS

476 part 5 , BS 476 part 6 , BS 476 part 7 ISO 1182 ASTM E662 Smoke Density - Melamine

laminated finish, perforated wooden grooved HDF slats L16-2 (2 mm grooves @ 8 mm

centers),tongue-groove edge for a seamless look of lineal dimension size 128 mm x 2440

mm x 16 mm thick having density 700 Kg /m3, weight -9 Kgs/m2 with back fleecs from

soundtex Germany nonwoven acoustic to be pasted on slats surco is to be installed by

using GI strut system. The technical parameters are as follows Core Variants - Fiberboard, 50 Sqm 6354.14 3,17,707.00

Climate (OC RH) – 50, 70 Light reflectance – 75%,Green (RC %) – 25, Hygiene (VoC, Clean

room) – Low, Class 1,Strength, Load capacity (Kg) - Anti sag, Ball-Impact. The concealed

wall paneling system shall include GI Wall channel (WC25) having thickness 0.45mm,

length 3600mm, unequal flanges of 15 & 20mm and web of 25mm should be fixed along

the perimeters of the wall with nylon sleeves and suitable fasteners at every 300mm

centers. Then fixed Main channels (MC45) having thickness 0.9mm, length 3600mm, equal

20 NS flanges of 15mm and web 45mm from the side wall & fixed at every 1200mm centers with

Providing and fixing wall vanity light 12 inch chrome finish with acrylic

21 NS diffuser with 7 watt led light warm white temparature range 2700k-3200k. 6.00 Nos. 4935.25 29,611.50

Providing and fixing wall hung mirror for bathroom with size 30inch by

22 NS 20inch 4mm thickness with all necessary fittings and fixtures included. Saint 4.00 Nos. 3454.67 13,818.68

Digitally signed by RAHUL

BOQ CIVIL NDSR-PSEB

4 Metal & Glass Work

Providing and fixing 8mm toughened clear glass in aluminium section used

for partition with necessary fittings and fixtures.

Fixing of 5/6mm premium quality lacquered glass on ply base with premium

24 NS quality silicone including glass, transportation, handling, fixing all complete. 10.00 sqm 4778.58 47,785.80

SS Door Handle 600mm height, for glass doors

Brass mortice lock, chrome plated.

Company - Godrej

Providing & fixing of Roller Blinds as per the approved sample with fabric

made up of 28% Polyesterand 68% PVC 4% alumlnlum layer on the back,

l2Stex Tilter Basket weave of thickness O.S3mm tS% (ISO 2286-2) and

wleghing 407gsmt5% with openess factor of 5% .The tear resistance (Warp

172Nt10% & ,Weft 153NH0%) As per ISO 544674, and pass NFPA 701 Fire

Resistnncc test, Vista Blinds

Providing and fixing Main entrance design in Charcoal louvers panelling on

wall along with vertical m.s section louvers finished with metal duco paint

column cladding with acrylic and ply wood paneling with 3d emblem and

brass lettering as per design.

Consider all with necessary fittings and fixtures

Providing and fixing Canvas painting of Minimum Size 6ftX3ft with suitable

29 NS design as approved by the Engineer In Charge 12.00 Nos. 9438.68 1,13,264.16

Providing ceramic planter pots of minimum size of 400mm height with

30 NS desired plants as approved by the Engineer In charge. 25 Nos. 3701.45 92,536.25

Digitally signed by RAHUL

BOQ LIGHTING WORK PESB

Renovation of Office of Public Enterprises Selection Board ( PESB) at Block No: 14, CGO Complex, Lodhi Road New

BILL OF QUANTITY FOR ELECTRICAL WORKS-NDSR ITEM FOR 5TH & 3 RD FLOOR

S No Item Specifications Quantity Unit Rate Amount

36W ImmaculateLED | CRCO 10, wipro panel light

1 2X2 Panel Light NS 6 Nos 2948.5 17,691.00

12W concealed ceiling LED COB. Black body color,

Company - Havells, Philips, Wipro or equivalent

Providing and fixing philips LNI1865A DN496B

LED12S-6500, down lighter

120 LEDs/m in 3500-4000K

4 COVE STRIP LIGHT NS 105.00 Meter 595.23 62,499.15

Company - Havells, Philips, Wipro or equivalent

120 LEDs/m in 3500-4000K, 18mm aluminium

5 NS profile without collar. 50.00 Meter 442.98 22,149.00

Company - Havells, Philips, Wipro or equivalent

Digitally signed by RAHUL

BOQ LIGHTING WORK PESB

36W linear hanging light in metal body as per

6 NS design, premium quality. 12.00 Nos 9717.62 1,16,611.44

Company - Havells, Philips, Wipro or equivalent

providing and fixing linear hanging light in metal

body as per design, premium quality. Philips

LINEAR HANGING model no SP800P LED38940L 120W6 CD PSD -4ft

LIGHT for members & under secretary room as specified

in the drawings

Providing and fixing decorative wall light chiffe

8 Decorative light NS 18.00 nos 4844.97 87,209.46

wall light. Product code 31455, philips

Blue Star Hot, Cold and Normal Water Dispenser

Corridor Water with Non Cooling Storage Cabinet - White & Blue

Storage Cabinet Stainless Steel, 230 Volts (AC), 500 Watts

complet in all respect.

providing and fixing HighSpeed Torpedo400mm

Wall-Mount Fans Best-In-Class Performance of

2100 RPM high speed and air delivery of 105

CMM, Wide Oscillation, Tilting mechanism, 100%

copper winding, power Source Corded Electric,

Noise level 5 db.

Digitally signed by RAHUL

BOQ LIGHTING WORK PESB

LED SCREENS - 42"

11 Directors & NS 106 cm (42 inch) Full HD LED Smart Android TV 4.00 Nos 58139.58 2,32,558.32

Supply of 1100V grade armoured cable having

sector / circular shaped copper conductor PVC

insulated cores under ground PVC tape wrapped

12 Cabling NS

inner sheathed, GI strip / wire armoured and

overall extruded PVC sheathed confirming to IS:

12.1 Cabling NS 25 Sq.mm 4 core copper cable 50.00 Mtr 1752.02 87,601.00

12.2 Cabling NS 16 Sq mm 4 core copper cable 50.00 Mtr 1246.16 62,308.00

Digitally signed by RAHUL

BOQ HVAC WORKS PESB

Renovation of Office of Public Enterprises Selection Board ( PESB) at Block No: 14, CGO

Complex, Lodhi Road New Delhi

BILL OF QUANTITY FOR HVAC WORKS-NDSR ITEM FOR 5TH & 3RD FLOOR

S.No. Description Capacity Unit Qty Rate Amount

Supply instatllation Testing Commissiong of

Air cooled DX type cassette unit internal

1 external unit including remote etc complet in

1.1 NS Secretary staff 2.0 TR Nos. 1 1,40,250.0 1,40,250.0

1.6 NS Lunch resting room 1.0 TR Nos. 1 66,342.5 66,342.5

1.10 NS Director Sec 1.0 TR Nos. 1 66,342.5 66,342.5

Digitally signed by RAHUL

BOQ HVAC WORKS PESB

S.No. Description Capacity Unit Qty Rate Amount

1.17 NS Chair person Office 2.0 TR Nos. 1 1,40,250.0 1,40,250.0

1.18 NS Chair person personal staff 1.5 TR Nos. 1 1,14,750.0 1,14,750.0

1.20 NS Opposite board room 1.5 TR Nos. 1 1,14,750.0 1,14,750.0

Providing and fixing M.S. structural support for

2 NS condensing External Unit including fatners, Nos. 24 7,000.0 1,68,000.0

staging if required in all respect.

Supply, installation, testing and commissioning

of 4 Core x 2.5 mm2 copper wire in PVC

conduit. (PVC conduit is including in the items)

complete in all respect.

Providing, fixing and testing insulated liquid and

suction copper piping.

i NS Liquid Line Rmtr. 350 977.5 3,42,125.0

ii NS Gas Line Rmtr. 350 1,062.5 3,71,875.0

Supply and fixing of 25mm dia PVC drain line

pipe with insulation complete in all respect.

TOTAL 33,00,790

Digitally signed by RAHUL

BOQ LV SYSTEM PESB

PESB, CGO OFFICE COMPLEX

Low Voltage Work Estimate

Renovation of Office of Public Enterprises Selection Board ( PESB) at Block No: 14, CGO Complex, Lodhi Road New Delhi

BILL OF QUANTITY FOR LV WORKS-NDSR ITEM FOR 5TH & 3RD FLOOR

S.No. / NS Unit Qty Rate Amount

Data & Telephone Network

Supply, Installation, Testing & Commissioning of CAT 6A UTP information outlet

(I/O) in accordance with ANSI TIA 568 C.2, IEC 60603-7-4 2nd Edition, ISO/IEC

1 NS TR 11801-9901-2014, ROHS Compliant. The I/O should have minimum and 200 NOS. 90 463.50 41,715.00

insertion cycle, UL approved for Data, Voice,cctv & Wifi at user end complete etc.

Supply, Installation, Testing & Commissioning of 1, 2 and 4 port face plate,

2 NS British Style with Shutter, 2 Plate system clear finish with transparent NOS. 45 279.00 12,555.00

labelling, ROHS Compliant, for cat6A I/O fixing at user side.

Supplying, installing, testing and commissioning of 24 port 19" modular Loaded

CAT 6A U/UTP patch panels available with block of four equipped with tool & tool

less IO, Rack Mountable complete with all labour and material required to

complete the job in all respect as per technical specifications enclosed.

Supplying and drawing of UTP 4 pair 23 AWG CAT 6A LAN cable in the existing

surface/ recessed steel/PVC conduit as required, conforming to the standards

4 NS ANSI/TIA 568 C.2, EN50173, IEC 11801 2nd ED, 700Mhz etc. complete as Mtrs 4500 56.10 2,52,450.00

required. (The contractor has to submit complete pentascanning of the network

from the OEM of the cable for which nothing extra will be paid)

Supplying, installing, testing and commissioning of following length of UTP 23

AWG Factory crimped CAT-6A Patch cord RoHS compliant complete as required.

5.2 NS 7 ft (At User Side Side) NOS. 90 378.00 34,020.00

Digitally signed by RAHUL

BOQ LV SYSTEM PESB

Supply, Installation, Testing & Commissioning of 24 port Core Switch with 24x

1/10/25G SFP+ ports ,minimum switching capacity of 1.2 Tbps, forwarding

performance of 1000 Mpps, support stacking/virtual chasis/Multi chassis Link

Aggregation(McLAG) upto 200 Gbps. It should have dual hot swappable internal

power supply, support 64K IPv4 and IPv6 Routes and 30K multicast routes, 250

k MAC Address, should support Routing protocols like OSPF v3, IS-IS, BGP, NAT,

with minimum 3 year support, Should be Common Criteria/NDPP/NDcPP

certified& IPv6 Logo Certified. RAM 8GB & Internal Flash memory 8GB, The

switch should be RoHS Compliant, Support management using CLI, GUI / Web

interface. Should be Common Criteria/NDPP/NDcPP & IPv6 Logo Certified. The

scope of work includes providing Stacking/McLAG cables wherever required

complete etc. as required as per the enclosed Technical specifications.

Supply, Installation, Testing & Commissioning of 24 port PoE+ Access Switch

with 24 x 10/100/1000BASE-T and 4 x 10G SFP+ uplink ports, minimum

switching capacity of 240 Gbps, forwarding performance 190 Mpps, minimum

PoE budget 370 Watt, support stacking/Multi chassis Link Aggregation(McLAG)

for minimum 5 switch with bandwidth of minimum 100 Gbps. It should have dual

hot swappable internal power supply, 4k Multicast Routes, should support

Routing protocols like OSPF, VRRP, VxLAN-EVPN, ISIS, with minimum 1 year

support, Should support min 2GB internal DRAM, 2GB internal Flash memory,

Should be Common Criteria/NDPP/NDcPP certified. The switch should be RoHS

Compliant, Support management using CLI, GUI / Web interface. The scope of

work includes providing Stacking/McLAG cables wherever required complete etc.

as required as per the enclosed Technical specifications

Supply, Installation, Testing & Commissioning of 10G base fiber Single mode

Modules complete etc. as required. (The OEM of Modules, Switch shall be same)

Supply, Installation, Testing & Commissioning of Indoor Wi-Fi Indoor Access

Point witjh standard OEM provided mounting bracket, arrangements, have an

1G/2.5G/5G Base-T PoE+ port, with 1x5Ghz IEEE 802.11ax and 1x2.4Ghz radios

Wi-Fi6 (802.11ax) bidirectional MU-MIMO, support 2x2 MU-MIMO 2.4GHz

Internal antennas, 4x4 MU-MIMO 5GHz Internal antennas, minimum of 3.0 Gbps

9 NS user throughput including both the radios, must support Automatic channel NOS. 4 58650.00 2,34,600.00

selection, must be EN 62368-1 , UL 62368-1 UL 2043 certified, data rate upto

2400 Mpbs, antennas with 3.9 dBi, should have WIPS, Dedicated Third Radio,

detection and blocking of rougue and honeypot Access Point, Operating temp. 0

to 40 degree complete with all accessories and as per enclosed specification etc.

Digitally signed by RAHUL

BOQ LV SYSTEM PESB

Supply, Installation, Testing & Commissioning of 3 mtr SM Fibre Patch Cord 3

mtr, Jacket should be LSZH sheath, Zirconia ceramic ferrule Connector: ,

10 NS Conector type Duplex LC LC, Patch Cord Should be GHMT/3P/ETL verified etc. to NOS. 8 2520.00 20,160.00

complete the job in all respect upto the entire satisfaction of Engineer-in charge

etc. as required.

Supply, installation, testing and commissioning of Operator work station with PC

having Intel Pentium I7 Processor including Serial ports (RS232) and USB ports

and following accessories etc. complete with software all as specified :

a. Minimum 8 Gigabytes of RAM memory

b. 2 TB of hard disk space

d. 21” LED colour monitor

e. Mouse with Mouse Pad

f. Standard Key Board

g. Latest Windows Operating System

Supply, Installation, Testing and Commissioning of 32 U (600W/800D) floor

12 NS mount rack with fans , 2 cable managers, satationary shelf , 2 Nos. of hardware NOS. 1 40230.00 40,230.00

pkts. complete etc.

Supply, laying, Testing & Commissioning of armoured 6 core Singlemode OS2,

Corrugated ECCS Armor, HDPE (UV) Sheathing, Gel filled OFC cable in pipe/duct/

13 NS on surface as per site requirement with 2 Nos steel music wire embedded in side Mtrs 200.00 118.80 23,760.00

sheathing as stregth member for switch connectivity. Cable should be ROHS

compliant and as per IEC60749-1 and as per technical specifications enclosed.

Supplying, Installing, Testing and Commissioning of 9U Equipment Rack (800w x

8OOd), with front 19" rails and 12x15/16 A power outlet PDUs, and mesh-screen

front and rear lockable doors, ventilated top cover with cable glands complete in

all respect as per technical specifications enclosed.

Digitally signed by RAHUL

BOQ LV SYSTEM PESB

Supply, Installation, Testing & Commissioning of 12 Port SM loaded LIU with LC

adaptor plates, have sufficient slots to accommodate 12/24/48 Duplex LC Ports

Single Mode/Multimode and to be loaded as per requirement with LC single

mode/Multimode pigtail and SM/MM LC duplex adaptors as per BOQ, Should have

fiber management provision inside, Should be rack mountable 1U/2U/3U/4U as

per capacity, Should have sufficient Splice holder as per capacity, Should have

15 NS Adapter body plus flange and integral quick-mounting clip, Protection class (IP- Each 2.00 10790.10 21,580.20

20 rated), Should have integral self-closing metal laser protection flaps, Should

have option for Visual coding, mechanical coding, and lock protection, Adaptor

should be UL listed, Adaptor should have semi transparent plastic dust covers,

allowing optical testing with test lasers without removing the covers, Bidder to

consider color coding for all input and output fiber patching in two different colors

complete as per enclosed specification etc as required.

Supply, installation, testing and commissioning of addressable Networkable

analogue addressable type fire alarm control panel complying to EN54 Standard

with min 640 Character / 240X64 Pixels / 5.5” graphic LCD display. The panel

should be equipped with sufficient numbers of loop with 10% spare capacity,

with each networkable intelligent fire alarm Control Panel having SLC with

capacity of min 200 detectors per loop with key pad, dual flash-based

microprocessor technology, inbuilt USB Port for upload and down load the

configuration tools, RS232 serial port for direct PC or modem connection, inbuilt

NAC's, min 20 programmable Zonal LEDs and operates on 240V AC + 10% with

50 Hz with built in charger. The panel shall have fire, fault relays, Option for BMS

integration MODBUS/ BACKNET, graphical software for provision of TCP/ IP

modules, Remote Access, provision of both class 'A' and class 'B' wiring in the

SLC circuit, user friendly with communication facility to monitor & control the

FACPs from a single window. The panel shall be VDS and FM approved, suitable

for minimum of 5000 event record facility, event fetch from FACP facility and the

single panel shall be suitable for min 2000 fire zones and 200 Panels/ Nodes in

Digitally signed by RAHUL

BOQ LV SYSTEM PESB

1.1 NS 1Loop Expandable upto 2Loop Each 1 244375.00 2,44,375.00

Supply, installation, testing and commissioning of Intellignet (Inbuilt Micro-

Controller) Analogue addressable Multi criteria (Heat + Smoke) detector with

2 NS inbuilt isolator as per EN54 Standard, Detector should be equiped with Dual NOS. 41 3501.00 1,43,541.00

single-colour LEDs providing 360° cone of visibility. (For Detectors/Device

without inbuilt isolator. Fault Isolator or Isolator base to be provided with each

detector/device)

Supply, installation, testing and commissioning of Analogue addressable Manual

Call Point (Resettable Type) with LED indicator and in-built fault isolator as per

3 NS EN54 Standard, to be supplied with Junction Box, Glands and other mounting NOS. 3 4320.00 12,960.00

accessories for proper installation.(Approved

Make:Gamewell,Advanced,Apollo,Thorn)

Supply, installation, testing and commissioning of Analogue Addressable Visual

Strobe having Min 10 distinct sound patterns/ multitone to indicate Exit doors

and direct occupants for safe and fast evacuation to be supplied with Junction

Box, Glands and other mounting accessories for proper installation.

Supply & Fixing of 2 core 1.5 sq.mm, multi strand, copper conductor, FRLS (Fire

5 NS Retardent Low Smoke)-PVC insulated GI Screened Armoured cable with saddle Mtrs 500 193.50 96,750.00

and required accessories.& Power Cable

Supply, installation, testing and commissioning of Response/Remote Indicator

which consists of steady glowing LED. This LED shall be mounted within a

6 NS Polycarbonate box and connected in parallel to the built in indicator of the NOS. 4 256.50 1,026.00

detector as per specifications. The RI shall come "ON" as soon as the detector

activates complete in all respects as per specification.

Supply, installation, testing and commissioning of Exit Signage Double Sided :

Ceiling mounted with Legends & complete accessories

8 NS RG6 Cable for TV Mtrs 200 37.80 7,560.00

9 NS Supplying and fixing of PVC Raceway complete with all accessories.

Supplying and fixing of 25 mm Medium class PVC conduit along with accesDSRies

10 NS in surface/recess including cutting the wall and making good the same in case of Mtrs 700 81 56,700.00

recessed conduit as required.

Supply Installation Testing and Commissioning of floor mounted Single Phase

Input and Single Phase Output 10 KVA online UPS for Control room rack

equipment, having 30 minutes (minimum) battery backup using SMF Battery ,

FREQUENCY RANGE 46 to 54 Hz, Transfer Time: AC mode to Battery mode 0

ms, Invertor mode to Bypass mode 0 ms, complete with 20nos 65ah batteries

i/c interconnections & M.S Rack for housing etc. as required.

TOTAL (DSR) 41,10,209.10

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

Renovation of Office of Public Enterprises Selection Board ( PESB) at Block No: 14, CGO Complex, Lodhi Road New Delhi

BILL OF QUANTITY FOR FURNITURE WORKS-NDSR ITEM FOR 5TH FLOOR

S No Woodwork & Furniture Specifications Quantity Unit Rate Amount

1 Members' Desk Providing and placing of Top surface of the table shall made up of MDF (Medium density fibre ) board duly finished with Veneer 1 Nos 146912.49 1,46,912.49

Size - 10' wide table with and final coating of PU. The Main desk should contain in built key board pull out tray for keeping keyboard of computer. The front

storage space modesty panel of the table shall be made up of MDF board of size 1640 mm x 600 mm x 16mm which shall also be duly finished

with Veener and PU coating. For personal storage one mobile pedestal (3 drawer unit) shall be provided of size 510 mm Width x

635 mm Height and 445 mm Depth. The storage pedestal shall also be made up of MDF duly finished with veener & final coating

of PU. The Side shall be of size 1200mm Width x 445mm Depth x 660 mm Height. The side unit shall be made up of MDF board

duly finshed with Veneer and final finish by PU Coating. The design of the side unit shall be such that it can be placed on either

side of the main table. The side unit shall contain open space for keeping cpu in extreme right side, one closed storage shutter at

extreme left end & open space in the middle with one shelf for keeping files. The thickness of the top of the side unit shall be

25mm. The Size of the Back unit shall be 2215mm width x 410 mm Depth x 2000mm height. The back unit shall be made up of

MDF board duly finished with veneer & final finish by PU coating. Below storage shall be provided with wooden shutters & the

upper left & right side of the back unit shall also be provided with wooden shutters. The middle 3 door shutters should be of glass

of minimum 5mm thick for display purpose. The hardness of the PU coating shall be 1.5H

2 Executive Chair Providing and Placing High Back Chair with overall size of 76.1 cm W x 76.1 cm D x 112.7 – 130.2 cm H x 43.1 – 53.1 cm Seat 1 Nos 17171.91 17,171.91

Height. The seat is cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with leatherette

and molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per IS:7888 for 25%

compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu molded M.S. ERW round tube

of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The armrest top is

molded from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x

0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5 steps. The

adjustable tilting mechanism is designed with following features : 360° revolving type, front-pivot for tilt with feet resting on

ground and continuous lumbar support ensuring more comfort, tilt tension adjustment can be operated in seating position, 5-

position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2, The mechanism housing is made up of

HPDC aluminium black powder coated. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth

adjustment range is of 6.0±0.5cm. Back frame is connected to the up/down mechanism in plastic T spine. It can be adjusted in the

range of 7.42±0.5 comfort the comfortable back support to suit individual need. The pneumatic height adjustment has an

adjustment stroke of 10.0±0.3cm. The pedestal is high pressure die cast polished aluminium & fitted with 5 nos. of twin wheel

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

3 Visitor's Chairs Providing and placing of The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA 4 Nos 7636.70 30,546.80

method described in OCP-QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam.

The dimensions of seat shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60

microns) tubular frame of dia 2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra

comfort. The back shall be upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x

70.5 cm (H). The HR polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888

for 25% compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The mechanism

shall be designed with 360° revolving type, 17±2° maximum tilt m pivot at centre, Upright position locking., Tilt tension

adjustment. The pneumatic height adjustment shall has an adjustment stroke of 11.0 ±0.3cm. The bellow shall be 3 piece

telescopic type and injection moulded in Black Polypropylene. The pedestal shall be injection moulded in black 33% glass-filled

Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). The

twin wheel castors shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 43.3 to max

54.3cm, Height - min99.5 to max 110.5cm, Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3

4 3 Seater Sofa Set cm.

Supplying and Placing in place of 3 seater sofa. The overall dimensions of the sofa shall be 2060W x 905D x 855H. The seat should 1 Nos 36825.20 36,825.20

be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu.

Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density 28 ± 2

kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette.

Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and termite proof as

per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring

assembly is mounted over understrucrure for cushioning effect. It should be a welded assembly made in Stainless steel (grade SS

202) tube & plate with plastic endcap.

5 1 Seater Sofa Set Supplying and Placing in place of 1 seater sofa. The overall dimensions of the sofa shall be 860W x 905D x 855H. The seat should 2 Nos 23081.00 46,162.00

be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu.

Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density 28 ± 2

kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette.

Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and termite proof as

per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring

assembly is mounted over understrucrure for cushioning effect. It should be a welded assembly made in Stainless steel (grade SS

202) tube & plate with plastic endcap.

6 Coffee Table Supplying and placing of Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade 1 Nos 11693.50 11,693.50

Size - 4'x 2' for fixing with understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall

dimensions of table shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

7 Low Height Cabinet Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal cladding of 0.8mm thk 1 Nos 16335.80 16,335.80

Size - 2'6" x 2' C.R.C.A (as per IS: 513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50±10 microns thickness.In case

of 2.5feet Height Storage units, wooden top is provided which is made of 25mm thick Pre-laminated board whereas 4.0feet and

4.5feet height Storage units are provided with 1 Imm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS: 513). The metal

tops are coated with Epoxy polyester powder of 50±10 microns thickness.

8 SECRETARY CABIN

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

9 Members' Desk Providing and placing of Top surface of the table shall made up of MDF (Medium density fibre ) board duly finished with Veneer 1 Nos 146912.49 1,46,912.49

Size - 10' wide table with and final coating of PU. The Main desk should contain in built key board pull out tray for keeping keyboard of computer. The front

storage space modesty panel of the table shall be made up of MDF board of size 1640 mm x 600 mm x 16mm which shall also be duly finished

with Veener and PU coating. For personal storage one mobile pedestal (3 drawer unit) shall be provided of size 510 mm Width x

635 mm Height and 445 mm Depth. The storage pedestal shall also be made up of MDF duly finished with veener & final coating

of PU. The Side shall be of size 1200mm Width x 445mm Depth x 660 mm Height. The side unit shall be made up of MDF board

duly finshed with Veneer and final finish by PU Coating. The design of the side unit shall be such that it can be placed on either

side of the main table. The side unit shall contain open space for keeping cpu in extreme right side, one closed storage shutter at

extreme left end & open space in the middle with one shelf for keeping files. The thickness of the top of the side unit shall be

25mm. The Size of the Back unit shall be 2215mm width x 410 mm Depth x 2000mm height. The back unit shall be made up of

MDF board duly finished with veneer & final finish by PU coating. Below storage shall be provided with wooden shutters & the

upper left & right side of the back unit shall also be provided with wooden shutters. The middle 3 door shutters should be of glass

of minimum 5mm thick for display purpose. The hardness of the PU coating shall be 1.5H

10 Executive Chair Providing and Placing High Back Chair with overall size of 76.1 cm W x 76.1 cm D x 112.7 – 130.2 cm H x 43.1 – 53.1 cm Seat 1 Nos 19079.90 19,079.90

Height. The seat is cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with leatherette

and molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per IS:7888 for 25%

compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu molded M.S. ERW round tube

of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The armrest top is

molded from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x

0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5 steps. The

adjustable tilting mechanism is designed with following features : 360° revolving type, front-pivot for tilt with feet resting on

ground and continuous lumbar support ensuring more comfort, tilt tension adjustment can be operated in seating position, 5-

position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2, The mechanism housing is made up of

HPDC aluminium black powder coated. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth

adjustment range is of 6.0±0.5cm. Back frame is connected to the up/down mechanism in plastic T spine. It can be adjusted in the

range of 7.42±0.5 comfort the comfortable back support to suit individual need. The pneumatic height adjustment has an

adjustment stroke of 10.0±0.3cm. The pedestal is high pressure die cast polished aluminium & fitted with 5 nos. of twin wheel

castors. The pedestal is 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection molded

in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal.

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

11 Visitor's Chairs Providing and placing of The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA 4 Nos 7636.70 30,546.80

method described in OCP-QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam.

The dimensions of seat shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60

microns) tubular frame of dia 2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra

comfort. The back shall be upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x

70.5 cm (H). The HR polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888

for 25% compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The mechanism

shall be designed with 360° revolving type, 17±2° maximum tilt m pivot at centre, Upright position locking., Tilt tension

adjustment. The pneumatic height adjustment shall has an adjustment stroke of 11.0 ±0.3cm. The bellow shall be 3 piece

telescopic type and injection moulded in Black Polypropylene. The pedestal shall be injection moulded in black 33% glass-filled

Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). The

twin wheel castors shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 43.3 to max

54.3cm, Height - min99.5 to max 110.5cm, Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3

12 3 Seater Sofa Set cm.

Supplying and Placing in place of 3 seater sofa. The overall dimensions of the sofa shall be 2060W x 905D x 855H. The seat should 1 Nos 36825.20 36,825.20

be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu.

Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density 28 ± 2

kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette.

Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and termite proof as

per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring

assembly is mounted over understrucrure for cushioning effect. It should be a welded assembly made in Stainless steel (grade SS

202) tube & plate with plastic endcap.

13 1 Seater Sofa Set Supplying and Placing in place of 1 seater sofa. The overall dimensions of the sofa shall be 860W x 905D x 855H. The seat should 2 Nos 23081.00 46,162.00

be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu.

Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density 28 ± 2

kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette.

Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and termite proof as

per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring

assembly is mounted over understrucrure for cushioning effect. It should be a welded assembly made in Stainless steel (grade SS

202) tube & plate with plastic endcap.

14 Coffee Table Supplying and placing of Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade 1 Nos 11693.50 11,693.50

Size - 4'x 2' for fixing with understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall

dimensions of table shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.

15 Low Height Cabinet Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal cladding of 0.8mm thk 1 Nos 16335.80 16,335.80

Size - 2'6" x 2' C.R.C.A (as per IS: 513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50±10 microns thickness.In case

of 2.5feet Height Storage units, wooden top is provided which is made of 25mm thick Pre-laminated board whereas 4.0feet and

4.5feet height Storage units are provided with 1 Imm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS: 513). The metal

tops are coated with Epoxy polyester powder of 50±10 microns thickness.

16 PS ROOM 01 0.00

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

17 PS Rooms Desk Providing in place of main table with overall size of table equal to 1350 x 600 x750mm. The table is made of 25 mm thick 1 Nos 19999.70 19,999.70

Size - 4'6" x 2' Prelaminated Twin Board of E1-P2 grade edge banded with matching 2mm thick PVC lipping. Grommet provided on work surface

for wire manaement. The modesty panel is made of 25 mm thick Prelaminated Twin Board of E1-P2 grade. The understructure is

made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC

lipping. The HInge door unit is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded

with matching 2 mm thick PVC lipping. Handles are provided for ease of opening. Pedestals are provided with lock for security.

The product must be UL Greenguard certified.

18 PS Rooms Desk Providing in place of main table with overall size of table equal to 1200 x 600 x750mm. The table is made of 25 mm thick 1 Nos 12570.30 12,570.30

Size - 3'6" x 3' Prelaminated Twin Board of E1-P2 grade edge banded with matching 2mm thick PVC lipping. Grommet provided on work surface

for wire manaement. The modesty panel is made of 25 mm thick Prelaminated Twin Board of E1-P2 grade. The understructure is

made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC

lipping. The HInge door unit is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded

with matching 2 mm thick PVC lipping. Handles are provided for ease of opening. Pedestals are provided with lock for security.

The product must be UL Greenguard certified.

19 Workstation Chairs The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method described in OCP- 2 Nos 7636.70 15,273.40

QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat

shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia

2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be

upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 70.5 cm (H). The HR

polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25%

compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The mechanism shall be

designed with 360° revolving type, 17±2° maximum tilt m pivot at centre, Upright position locking., Tilt tension adjustment. The

pneumatic height adjustment shall has an adjustment stroke of 11.0 ±0.3cm. The bellow shall be 3 piece telescopic type and

injection moulded in Black Polypropylene. The pedestal shall be injection moulded in black 33% glass-filled Nylon66 and fitted

with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). The twin wheel castors

shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 43.3 to max 54.3cm, Height -

min99.5 to max 110.5cm, Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.

20 Visitor's Chairs The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method described in OCP- 2 Nos 5730.30 11,460.60

QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat

shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia

2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be

upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 60.5 cm (H). The HR

polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25%

compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The powder coated (DFT

40-60 microns) tubular frame shall be cantilever type & made of dia 2.54±0.03cm x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. Overall

Dimensions of Chair shall be Seat Height - 46.5cm, Height - 93.5cm, Width & Depth of Chair as measured from pedestal -Width-

61.0 cm and Depth-64.5 cm.

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

21 Coffee Table Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with 1 Nos 11693.50 11,693.50

Size - 1'6"x 1' understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of

table shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

22 Storage Cabinet Aesthetically appealing completely knock down construction.The add—on units are stack widthwise to form a row of storage 1 Nos 40000.40 40,000.40

SIze - 10' x 2'6" having a common side panel. (Note— Single Main unit should not be offered.Minimum 1 Main + IAddon to be offered)Legs fitted

with screw typeleveler(add 45mm to the height).Made from combination of CRCA** 0.5 mm &

0.8mm Thickness.CRCA 'D' Grade as per IS-513.

23 Low Height Cabinet Aesthetically appealing completely knock down construction.The add—on units are stack widthwise to form a row of storage 1 Nos 36123.60 36,123.60

Size - 8' x 2'6" having a common side panel. (Note— Single Main unit should not be offered.Minimum 1 Main + IAddon to be offered)Legs fitted

with screw typeleveler(add 45mm to the height).Made from combination of CRCA** 0.5 mm &

0.8mm Thickness.CRCA 'D' Grade as per IS-513.

24 PS ROOM 02 0.00

25 PS Rooms Desk Providing in place of main table with overall size of table equal to 1200 x 600 x750mm. The table is made of 25 mm thick 1 Nos 12570.30 12,570.30

Size - 3'6" x 2' Prelaminated Twin Board of E1-P2 grade edge banded with matching 2mm thick PVC lipping. Grommet provided on work surface

for wire manaement. The modesty panel is made of 25 mm thick Prelaminated Twin Board of E1-P2 grade. The understructure is

made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC

lipping. The HInge door unit is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded

with matching 2 mm thick PVC lipping. Handles are provided for ease of opening. Pedestals are provided with lock for security.

The product must be UL Greenguard certified.

26 PS Rooms Desk Providing in place of main table with overall size of table equal to 1200 x 600 x750mm. The table is made of 25 mm thick 1 Nos 12570.30 12,570.30

Size - 4' x 2' Prelaminated Twin Board of E1-P2 grade edge banded with matching 2mm thick PVC lipping. Grommet provided on work surface

for wire manaement. The modesty panel is made of 25 mm thick Prelaminated Twin Board of E1-P2 grade. The understructure is

made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC

lipping. The HInge door unit is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded

with matching 2 mm thick PVC lipping. Handles are provided for ease of opening. Pedestals are provided with lock for security.

The product must be UL Greenguard certified.

27 Workstation Chairs The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method described in OCP- 2 Nos 7636.70 15,273.40

QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat

shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia

2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be

upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 70.5 cm (H). The HR

polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25%

compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The mechanism shall be

designed with 360° revolving type, 17±2° maximum tilt m pivot at centre, Upright position locking., Tilt tension adjustment. The

pneumatic height adjustment shall has an adjustment stroke of 11.0 ±0.3cm. The bellow shall be 3 piece telescopic type and

injection moulded in Black Polypropylene. The pedestal shall be injection moulded in black 33% glass-filled Nylon66 and fitted

with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). The twin wheel castors

shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 43.3 to max 54.3cm, Height -

min99.5 to max 110.5cm, Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

28 Visitor's Chairs The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method described in OCP- 2 Nos 5730.30 11,460.60

QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat

shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia

2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be

upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 60.5 cm (H). The HR

polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25%

compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The powder coated (DFT

40-60 microns) tubular frame shall be cantilever type & made of dia 2.54±0.03cm x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. Overall

Dimensions of Chair shall be Seat Height - 46.5cm, Height - 93.5cm, Width & Depth of Chair as measured from pedestal -Width-

61.0 cm and Depth-64.5 cm.

29 Coffee Table Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with 1 Nos 11693.50 11,693.50

Size - 1'6"x 1' understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of

table shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.

30 Storage Cabinet Aesthetically appealing completely knock down construction.The add—on units are stack widthwise to form a row of storage 1 Nos 36123.60 36,123.60

Size - 8'x 2'6" having a common side panel. (Note— Single Main unit should not be offered.Minimum 1 Main + IAddon to be offered)Legs fitted

with screw typeleveler(add 45mm to the height).Made from combination of CRCA** 0.5 mm &

0.8mm Thickness.CRCA 'D' Grade as per IS-513.

31 PS ROOM 03 0.00

32 PS Room Desk Providing in place of main table with overall size of table equal to 1200 x 600 x750mm. The table is made of 25 mm thick 1 Nos 12570.30 12,570.30

Size - 3' x 2' Prelaminated Twin Board of E1-P2 grade edge banded with matching 2mm thick PVC lipping. Grommet provided on work surface

for wire manaement. The modesty panel is made of 25 mm thick Prelaminated Twin Board of E1-P2 grade. The understructure is

made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC

lipping. The HInge door unit is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded

with matching 2 mm thick PVC lipping. Handles are provided for ease of opening. Pedestals are provided with lock for security.

The product must be UL Greenguard certified.

33 PS Room Desk Providing in place of main table with overall size of table equal to 1200 x 600 x750mm. The table is made of 25 mm thick 2 Nos 12570.30 25,140.60

Size - 2' x 3'6" Prelaminated Twin Board of E1-P2 grade edge banded with matching 2mm thick PVC lipping. Grommet provided on work surface

for wire manaement. The modesty panel is made of 25 mm thick Prelaminated Twin Board of E1-P2 grade. The understructure is

made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC

lipping. The HInge door unit is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded

with matching 2 mm thick PVC lipping. Handles are provided for ease of opening. Pedestals are provided with lock for security.

The product must be UL Greenguard certified.

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

34 Workstation Chairs The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method described in OCP- 3 Nos 7636.70 22,910.10

QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat

shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia

2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be

upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 70.5 cm (H). The HR

polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25%

compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The mechanism shall be

designed with 360° revolving type, 17±2° maximum tilt m pivot at centre, Upright position locking., Tilt tension adjustment. The

pneumatic height adjustment shall has an adjustment stroke of 11.0 ±0.3cm. The bellow shall be 3 piece telescopic type and

injection moulded in Black Polypropylene. The pedestal shall be injection moulded in black 33% glass-filled Nylon66 and fitted

with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). The twin wheel castors

shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 43.3 to max 54.3cm, Height -

min99.5 to max 110.5cm, Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.

35 Visitor's Chairs The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method described in OCP- 2 Nos 5730.30 11,460.60

QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat

shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia

2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be

upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 60.5 cm (H). The HR

polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25%

compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The powder coated (DFT

40-60 microns) tubular frame shall be cantilever type & made of dia 2.54±0.03cm x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. Overall

Dimensions of Chair shall be Seat Height - 46.5cm, Height - 93.5cm, Width & Depth of Chair as measured from pedestal -Width-

61.0 cm and Depth-64.5 cm.

36 Coffee Table Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with 1 Nos 11693.50 11,693.50

Size - 1'6"x 1' understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of

table shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.

37 Storage Cabinet Aesthetically appealing completely knock down construction.The add—on units are stack widthwise to form a row of storage 1 Nos 36123.60 36,123.60

Size - 8'x 2'6" having a common side panel. (Note— Single Main unit should not be offered.Minimum 1 Main + IAddon to be offered)Legs fitted

with screw typeleveler(add 45mm to the height).Made from combination of CRCA** 0.5 mm &

0.8mm Thickness.CRCA 'D' Grade as per IS-513.

38 LUNCH/ RESTING ROOM 0.00

39 Center Table Overall Size : Width : 120cm Depth : 60cm Height : 36.7cm Materials : All carcass panel are made of 18 mm prelaminated particle 1 Nos 15061.40 15,061.40

Size - 4' x 2' board with edge banding 1.5 mm thickness.Drawer bottom is made of .9 mm thick prelaminated particle board .Drawer front is

made of 18 mm thick PU painted MDF . Legs : Rubber wood . Hardware : Hettich . Construction : Knock down .Finish : All 18 mm

prelaminated particle board panels are Noce Versaillies with walnut edge band. PU lamination is high gloss in Ecru shade .Packets

: 1 nos . Materials : All carcass panel are made of 18 mm prelaminated particle board with edge banding 1.5 mm thickness.

Hardware : Hettich . Construction : Knock down .Finish : • All 18 mm prelaminated particle board panels are Noce Versaillies with

walnut edge band . PU lamination is high gloss in Ecru shade .Packets : 1 nos.

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

40 Counter Chairs UNIQUE BACK-TILT: A unique back-tilt feature allows an upright as well as relaxed angle, thus reducing pressure on the inter- 4 Nos 14440.30 57,761.20

vertebral discs during long training sessions • MOTHER’S HUG: Derived from the Mother’s Hug, the body hugging contours

comfortably supports your back • BROAD ARMREST: Scratch resistant broad armrest ensures proper comfort to arms during long

sitting hours • BRAKE CASTERS: Brake Casters in the desklet version ensures firm grip on floor while one is seated and facilitates

various room layouts unoccupied with its mobility • Adjustable anti slide footring to suit your seated height with comfort. Turning

around feature to provide more collaborative workspace.716x716x1220mm.

41 Top Cabinet Aesthetically appealing completely knock down construction.The add—on units are stack widthwise to form a row of storage 1 Nos 30262.70 30,262.70

Size - 7' x 2'6" having a common side panel. (Note— Single Main unit should not be offered.Minimum 1 Main + IAddon to be offered)Legs fitted

with screw typeleveler(add 45mm to the height).Made from combination of CRCA** 0.5 mm &

0.8mm Thickness.CRCA 'D' Grade as per IS-513.

42 SECRETARY'S STAFF ROOM 0.00

43 Secretary Staff Room Main Desk size shall be 1804 Width x 450 Depth x 750 Height. Top shall be made up of PVC membrane pressed of 25 mm thick 2 Nos 40736.60 81,473.20

Desks MDF - one side laminate board with 0.4 mm PVC membrane Pressed on to tops. The top shall be having duck nose and half round

Size - 5'6" x 2' profile edges and top is made in only one finish which is European Ash.

44 Secretary Staff Room Main Desk size shall be 1200 Width x 600 Depth x 743 Height . Top shall be of 18 mm thickness made of PLT board with 2 mm 2 Nos 15905.50 31,811.00

Desks Edge banding. Wenge and savannah Maple PLT board shall be used. The Understructure shall be in pre-laminated panels made

Size - 3'6" x 2' with PLT boards . 2- Drawerand 3 - Drawer storage units with different combinations to support tops made with 18 mm PLT

boards of different colours.Modesty and back panels made with 18 mm PLT boards. The pedestals / storages shall be fitted with

necessary locks.

45 Desk Main Desk size shall be 1200 Width x 600 Depth x 743 Height . Top shall be of 18 mm thickness made of PLT board with 2 mm 1 Nos 15905.50 15,905.50

Size - 2'6" x 1'6" Edge banding. Wenge and savannah Maple PLT board shall be used. The Understructure shall be in pre-laminated panels made

with PLT boards . 2- Drawerand 3 - Drawer storage units with different combinations to support tops made with 18 mm PLT

boards of different colours.Modesty and back panels made with 18 mm PLT boards. The pedestals / storages shall be fitted with

necessary locks.

46 Workstation Chairs The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method described in OCP- 5 Nos 7636.70 38,183.50

QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat

shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia

2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be

upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 70.5 cm (H). The HR

polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25%

compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The mechanism shall be

designed with 360° revolving type, 17±2° maximum tilt m pivot at centre, Upright position locking., Tilt tension adjustment. The

pneumatic height adjustment shall has an adjustment stroke of 11.0 ±0.3cm. The bellow shall be 3 piece telescopic type and

injection moulded in Black Polypropylene. The pedestal shall be injection moulded in black 33% glass-filled Nylon66 and fitted

with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). The twin wheel castors

shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 43.3 to max 54.3cm, Height -

min99.5 to max 110.5cm, Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

47 Visitor's Chairs The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method described in OCP- 4 Nos 5730.30 22,921.20

QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat

shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia

2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be

upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 60.5 cm (H). The HR

polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25%

compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The powder coated (DFT

40-60 microns) tubular frame shall be cantilever type & made of dia 2.54±0.03cm x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. Overall

Dimensions of Chair shall be Seat Height - 46.5cm, Height - 93.5cm, Width & Depth of Chair as measured from pedestal -Width-

61.0 cm and Depth-64.5 cm.

48 3 Seater Sofa Set Providing and placing in position of 3 seater sofa. The overall dimensions of the sofa shall be 2060W x 905D x 855H. The seat 1 Nos 36822.40 36,822.40

should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2

kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density

28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or

leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and

termite proof as per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm

dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should be a welded assembly made in

Stainless steel (grade SS 202) tube & plate with plastic endcap.

49 Coffee Table Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with 1 Nos 11693.50 11,693.50

Size - 4'x 2' understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of

table shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.

50 Full Height Cabinet Aesthetically appealing completely knock down construction.The add—on units are stack widthwise to form a row of storage 1 Nos 36123.60 36,123.60

Size - 8' x 2'6" having a common side panel. (Note— Single Main unit should not be offered.Minimum 1 Main + IAddon to be offered)Legs fitted

with screw typeleveler(add 45mm to the height).Made from combination of CRCA** 0.5 mm &

0.8mm Thickness.CRCA 'D' Grade as per IS-513.

51 Full Height Cabinet Aesthetically appealing completely knock down construction.The add—on units are stack widthwise to form a row of storage 2 Nos 36123.60 72,247.20

Size - 8' x 2'6" having a common side panel. (Note— Single Main unit should not be offered.Minimum 1 Main + IAddon to be offered)Legs fitted

with screw typeleveler(add 45mm to the height).Made from combination of CRCA** 0.5 mm &

0.8mm Thickness.CRCA 'D' Grade as per IS-513 .

52 Top Cabinet Aesthetically appealing completely knock down construction.The add—on units are stack widthwise to form a row of storage 1 Nos 40000.40 40,000.40

Size - 10' x 2'6" having a common side panel. (Note— Single Main unit should not be offered.Minimum 1 Main + IAddon to be offered)Legs fitted

with screw typeleveler(add 45mm to the height).Made from combination of CRCA** 0.5 mm &

0.8mm Thickness.CRCA 'D' Grade as per IS-513.

53 DIRECTOR'S CABIN 01 0.00

54 Director's Cabin Desk Main Desk size shall be 1804 Width x 450 Depth x 750 Height. Top shall be made up of PVC membrane pressed of 25 mm thick 1 Nos 40736.60 40,736.60

with storage space MDF - one side laminate board with 0.4 mm PVC membrane Pressed on to tops. The top shall be having duck nose and half round

Size - 5' x 2' profile edges and top is made in only one finish which is European Ash.

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

55 Executive Chair Providing and Placing High Back Chair with overall size of 76.1 cm W x 76.1 cm D x 112.7 – 130.2 cm H x 43.1 – 53.1 cm Seat 1 Nos 19079.90 19,079.90

Height. The seat is cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with leatherette

and molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per IS:7888 for 25%

compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu molded M.S. ERW round tube

of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The armrest top is

molded from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x

0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5 steps. The

adjustable tilting mechanism is designed with following features : 360° revolving type, front-pivot for tilt with feet resting on

ground and continuous lumbar support ensuring more comfort, tilt tension adjustment can be operated in seating position, 5-

position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2, The mechanism housing is made up of

HPDC aluminium black powder coated. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth

adjustment range is of 6.0±0.5cm. Back frame is connected to the up/down mechanism in plastic T spine. It can be adjusted in the

range of 7.42±0.5 comfort the comfortable back support to suit individual need. The pneumatic height adjustment has an

56 Visitor's Chairs adjustment

The stroke shall

seat assembly of 10.0±0.3cm.

1.2 ±0.1cm.is high pressure

thick die cast

hot-pressed polished

plywood aluminium

measured & fitted

as per with 5 nos.

QA method of twininwheel

described OCP- 2 Nos 7636.70 15,273.40

QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat

shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia

2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be

upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 70.5 cm (H). The HR

polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25%

compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The mechanism shall be

designed with 360° revolving type, 17±2° maximum tilt m pivot at centre, Upright position locking., Tilt tension adjustment. The

pneumatic height adjustment shall has an adjustment stroke of 11.0 ±0.3cm. The bellow shall be 3 piece telescopic type and

injection moulded in Black Polypropylene. The pedestal shall be injection moulded in black 33% glass-filled Nylon66 and fitted

with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). The twin wheel castors

shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 43.3 to max 54.3cm, Height -

min99.5 to max 110.5cm, Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.

57 3 Seater Sofa Set Providing and placing in position of 3 seater sofa. The overall dimensions of the sofa shall be 2060W x 905D x 855H. The seat 1 Nos 36825.20 36,825.20

should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2

kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density

28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or

leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and

termite proof as per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm

dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should be a welded assembly made in

Stainless steel (grade SS 202) tube & plate with plastic endcap.

58 Coffee Table Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with 1 Nos 11693.50 11,693.50

Size - 4'x 2' understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of

table shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.

59 Low Height Cabinet Aesthetically appealing completely knock down construction.The add—on units are stack widthwise to form a row of storage 1 Nos 25435.90 25,435.90

Size - 6' x 2'6" having a common side panel. (Note— Single Main unit should not be offered.Minimum 1 Main + IAddon to be offered)

Legs fitted with screw type leveler

(add 45mm to the height)

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

60 DIRECTOR'S CABIN 02 0.00

61 Director's Cabin Desk Main Desk size shall be 1500 Width x 450 Depth x 750 Height. Top shall be made up of PVC membrane pressed of 25 mm thick 1 Nos 40736.60 40,736.60

with storage space MDF - one side laminate board with 0.4 mm PVC membrane Pressed on to tops. The top shall be having duck nose and half round

Size - 5' x 2' profile edges and top is made in only one finish which is European Ash.

62 Executive Chair Providing and Placing High Back Chair with overall size of 76.1 cm W x 76.1 cm D x 112.7 – 130.2 cm H x 43.1 – 53.1 cm Seat 1 Nos 19079.90 19,079.90

Height. The seat is cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with leatherette

and molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per IS:7888 for 25%

compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu molded M.S. ERW round tube

of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The armrest top is

molded from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x

0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5 steps. The

adjustable tilting mechanism is designed with following features : 360° revolving type, front-pivot for tilt with feet resting on

ground and continuous lumbar support ensuring more comfort, tilt tension adjustment can be operated in seating position, 5-

position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2, The mechanism housing is made up of

HPDC aluminium black powder coated. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth

adjustment range is of 6.0±0.5cm. Back frame is connected to the up/down mechanism in plastic T spine. It can be adjusted in the

range of 7.42±0.5 comfort the comfortable back support to suit individual need. The pneumatic height adjustment has an

63 Visitor's Chairs adjustment

The stroke shall

seat assembly of 10.0±0.3cm.

1.2 ±0.1cm.is high pressure

thick die cast

hot-pressed polished

plywood aluminium

measured & fitted

as per with 5 nos.

QA method of twininwheel

described OCP- 2 Nos 7636.70 15,273.40

QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat

shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia

2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be

upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 60.5 cm (H). The HR

polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25%

compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The powder coated (DFT

40-60 microns) tubular frame shall be cantilever type & made of dia 2.54±0.03cm x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. Overall

Dimensions of Chair shall be Seat Height - 46.5cm, Height - 93.5cm, Width & Depth of Chair as measured from pedestal -Width-

61.0 cm and Depth-64.5 cm.

64 3 Seater Sofa Set Providing and placing in position of 3 seater sofa. The overall dimensions of the sofa shall be 2060W x 905D x 855H. The seat 1 Nos 36825.20 36,825.20

should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2

kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density

28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or

leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and

termite proof as per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm

dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should be a welded assembly made in

Stainless steel (grade SS 202) tube & plate with plastic endcap.

65 Coffee Table Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with 1 Nos 11693.50 11,693.50

Size - 4'x 2' understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of

table shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.

66 Low Height Cabinet Aesthetically appealing completely knock down construction.The add—on units are stack widthwise to form a row of storage 1 Nos 28257.90 28,257.90

Size - 6' x 2'6" having a common side panel. (Note— Single Main unit should not be offered.Minimum 1 Main + IAddon to be offered)

Legs fitted with screw type leveler

(add 45mm to the height).

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

67 ADMIN ROOM 0.00

68 Admin Room Desks Made of 25mm Thick Pre-laminated board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with 4 Nos 12392.30 49,569.20

Size - 3' x 2' matching 2 mm thick PVC lipping. Access Flap provided on work surface for wire management Worktop Modesty Panel Legs Made

of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconfirming to IS-12823:1990, Edge banded with

matching 2 mm thick PVC lipping. Cube legs are fabricated from MS ERW Tube of 50 mm x 25 mm x 1.2mm thick and40 mm x 40

mm x 1.2 mm thick (as per IS: 7138). At the top surface of leg, support brackets of 3 mm thick HR (as per IS: 2062) are welded for

fixing worktop. These arewelded together by argo shield welding. This welded structure is coated with 50 micron epoxy polyester

coating. At the base, a plastic cap with M8 molded insert is fixed, on to which a straight M8 leveler fitted which allows for

adjustment of the height.

69 Workstation Chairs The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method described in OCP- 4 Nos 7636.70 30,546.80

QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat

shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia

2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be

upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 70.5 cm (H). The HR

polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25%

compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The mechanism shall be

designed with 360° revolving type, 17±2° maximum tilt m pivot at centre, Upright position locking., Tilt tension adjustment. The

pneumatic height adjustment shall has an adjustment stroke of 11.0 ±0.3cm. The bellow shall be 3 piece telescopic type and

injection moulded in Black Polypropylene. The pedestal shall be injection moulded in black 33% glass-filled Nylon66 and fitted

with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). The twin wheel castors

shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 43.3 to max 54.3cm, Height -

min99.5 to max 110.5cm, Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.

70 Full Height Cabinet Aesthetically appealing completely knock down construction.The add—on units are stack widthwise to form a row of storage 1 Nos 38896.00 38,896.00

Size - 9' x 2'6" having a common side panel. (Note— Single Main unit should not be offered.Minimum 1 Main + IAddon to be offered)

Legs fitted with screw type leveler

(add 45mm to the height)

71 DAK ROOM 0.00

72 Dak Room Desks Made of 25mm Thick Pre-laminated board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with 4 Nos 11313.27 45,253.08

Size - 3' x 2' matching 2 mm thick PVC lipping. Access Flap provided on work surface for wire management Worktop Modesty Panel Legs Made

of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconfirming to IS-12823:1990, Edge banded with

matching 2 mm thick PVC lipping. Cube legs are fabricated from MS ERW Tube of 50 mm x 25 mm x 1.2mm thick and40 mm x 40

mm x 1.2 mm thick (as per IS: 7138). At the top surface of leg, support brackets of 3 mm thick HR (as per IS: 2062) are welded for

fixing worktop. These arewelded together by argo shield welding. This welded structure is coated with 50 micron epoxy polyester

coating. At the base, a plastic cap with M8 molded insert is fixed, on to which a straight M8 leveler fitted which allows for

adjustment of the height.

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

73 Workstation Chairs The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method described in OCP- 4 Nos 7636.70 30,546.80

QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat

shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia

2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be

upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 70.5 cm (H). The HR

polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25%

compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The mechanism shall be

designed with 360° revolving type, 17±2° maximum tilt m pivot at centre, Upright position locking., Tilt tension adjustment. The

pneumatic height adjustment shall has an adjustment stroke of 11.0 ±0.3cm. The bellow shall be 3 piece telescopic type and

injection moulded in Black Polypropylene. The pedestal shall be injection moulded in black 33% glass-filled Nylon66 and fitted

with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). The twin wheel castors

shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 43.3 to max 54.3cm, Height -

min99.5 to max 110.5cm, Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.

74 Full Height Cabinet Aesthetically appealing completely knock down construction.The add—on units are stack widthwise to form a row of storage 1 Nos 38896.00 38,896.00

Size - 9' x 2'6" having a common side panel. (Note— Single Main unit should not be offered.Minimum 1 Main + IAddon to be offered)

Legs fitted with screw type leveler

(add 45mm to the height)

75 SECTION 01 0.00

76 Section 01 Desk Main Desk size shall be 1500 Width x 450 Depth x 750 Height. Top shall be made up of PVC membrane pressed of 25 mm thick 3 Nos 36662.94 1,09,988.82

Size - 5' x 2' MDF - one side laminate board with 0.4 mm PVC membrane Pressed on to tops. The top shall be having duck nose and half round

profile edges and top is made in only one finish which is European Ash.

77 Section 01 Desk Providing in place of main table with overall size of table equal to 1200 x 600 x750mm. The table is made of 25 mm thick 18 Nos 12570.30 2,26,265.40

Size - 3'6" x 2' Prelaminated Twin Board of E1-P2 grade edge banded with matching 2mm thick PVC lipping. Grommet provided on work surface

for wire manaement. The modesty panel is made of 25 mm thick Prelaminated Twin Board of E1-P2 grade. The understructure is

made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC

lipping. The HInge door unit is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded

with matching 2 mm thick PVC lipping. Handles are provided for ease of opening. Pedestals are provided with lock for security.

Consider 2 ft ht pin board with fabric at workstations as per requirement. The product must be UL Greenguard certified

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

78 Executive Chair Providing and Placing High Back Chair with overall size of 76.1 cm W x 76.1 cm D x 112.7 – 130.2 cm H x 43.1 – 53.1 cm Seat 1 Nos 19079.90 19,079.90

Height. The seat is cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with leatherette

and molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per IS:7888 for 25%

compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu molded M.S. ERW round tube

of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The armrest top is

molded from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x

0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5 steps. The

adjustable tilting mechanism is designed with following features : 360° revolving type, front-pivot for tilt with feet resting on

ground and continuous lumbar support ensuring more comfort, tilt tension adjustment can be operated in seating position, 5-

position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2, The mechanism housing is made up of

HPDC aluminium black powder coated. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth

adjustment range is of 6.0±0.5cm. Back frame is connected to the up/down mechanism in plastic T spine. It can be adjusted in the

range of 7.42±0.5 comfort the comfortable back support to suit individual need. The pneumatic height adjustment has an

adjustment stroke of 10.0±0.3cm. The pedestal is high pressure die cast polished aluminium & fitted with 5 nos. of twin wheel

castors. The pedestal is 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection molded

in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal.

79 Workstation Chairs The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method described in OCP- 18 Nos 7636.70 1,37,460.60

QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat

shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia

2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be

upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 70.5 cm (H). The HR

polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25%

compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The mechanism shall be

designed with 360° revolving type, 17±2° maximum tilt m pivot at centre, Upright position locking., Tilt tension adjustment. The

pneumatic height adjustment shall has an adjustment stroke of 11.0 ±0.3cm. The bellow shall be 3 piece telescopic type and

injection moulded in Black Polypropylene. The pedestal shall be injection moulded in black 33% glass-filled Nylon66 and fitted

with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). The twin wheel castors

shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 43.3 to max 54.3cm, Height -

min99.5 to max 110.5cm, Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.

80 Visitor's Chairs The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method described in OCP- 4 Nos 5730.30 22,921.20

QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat

shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia

2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be

upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 60.5 cm (H). The HR

polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25%

compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The powder coated (DFT

40-60 microns) tubular frame shall be cantilever type & made of dia 2.54±0.03cm x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. Overall

Dimensions of Chair shall be Seat Height - 46.5cm, Height - 93.5cm, Width & Depth of Chair as measured from pedestal -Width-

61.0 cm and Depth-64.5 cm.

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

81 Low Height Cabinet Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal cladding of 0.8mm thk 1 Nos 20505.80 20,505.80

Size - 3'6" x 2'6" C.R.C.A (as per IS: 513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50±10 microns thickness.In case

of 2.5feet Height Storage units, wooden top is provided which is made of 25mm thick Pre-laminated board whereas 4.0feet and

4.5feet height Storage units are provided with 1 Imm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS: 513). The metal

tops are coated with Epoxy polyester powder of 50±10 microns thickness.

82 U.S CABIN 01 0.00

83 U.S Cabin 01 Desk Main Desk size shall be 1500 Width x 450 Depth x 750 Height. Top shall be made up of PVC membrane pressed of 25 mm thick 1 Nos 40736.60 40,736.60

Size - 5' x 2' MDF - one side laminate board with 0.4 mm PVC membrane Pressed on to tops. The top shall be having duck nose and half round

profile edges and top is made in only one finish which is European Ash.

84 Executive Chair Made of 25mm Thick Pre-laminated board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with 1 Nos 19079.90 19,079.90

matching 2 mm thick PVC lipping. Access Flap provided on work surface for wire management Worktop Modesty Panel Legs Made

of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconfirming to IS-12823:1990, Edge banded with

matching 2 mm thick PVC lipping. Cube legs are fabricated from MS ERW Tube of 50 mm x 25 mm x 1.2mm thick and40 mm x 40

mm x 1.2 mm thick (as per IS: 7138). At the top surface of leg, support brackets of 3 mm thick HR (as per IS: 2062) are welded for

fixing worktop. These arewelded together by argo shield welding. This welded structure is coated with 50 micron epoxy polyester

coating. At the base, a plastic cap with M8 molded insert is fixed, on to which a straight M8 leveler fitted which allows for

adjustment of the height.

85 Visitor's Chairs The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method described in OCP- 2 Nos 5730.30 11,460.60

QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat

shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia

2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be

upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 60.5 cm (H). The HR

polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25%

compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The powder coated (DFT

40-60 microns) tubular frame shall be cantilever type & made of dia 2.54±0.03cm x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. Overall

Dimensions of Chair shall be Seat Height - 46.5cm, Height - 93.5cm, Width & Depth of Chair as measured from pedestal -Width-

61.0 cm and Depth-64.5 cm.

86 2 Seater Sofa Set Providing and placing in position of 2 seater sofa. The overall dimensions of the sofa shall be 1460W x 905D x 855H. The seat 1 Nos 30081.80 30,081.80

should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2

kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density

28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or

leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and

termite proof as per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm

dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should be a welded assembly made in

Stainless steel (grade SS 202) tube & plate with plastic endcap.

87 SECTION 02 0.00

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

88 Section 02 Desk Size shall be 1500 Width mm x 750 Depth mm x 728 Height mm . Top shall be 18 mm thick Pre laminated particle board all 1 Nos 23718.50 23,718.50

Size - 5' x 2' work surface edges shall be having duly sealed with 2 mm thick PVC edgebanding. Understructure Modesty Panel 18 mm thick Pre

laminated particle board . The Rectangular frame shall be fabricated component in 1.2 mm thick CRCA , Finish : powder Coat(

epoxy polyster) . Leg shall be fabricated component in 38 mm x 25 mm 1.2 mm thick MS ERW ATube ,finish powder coat ( epoxy

polyster).The plastic cap for cable travel shall be injection moulded polypropylene and leveler glide for shall be nylon 6 & MS bolt.

The storage shall be having shell and drawer tray 0.6 mm thick CRCA Finish powder coat (epoxy polyster) plus the drawer front

shall be 0.8 mm thick CRCA Finish powder coat (epoxy polyster) plus lock with 10 lever and handle and leveller. The wire

management shall be horizontal wire carrier 0.7 mm thick CRCA Finish powder coat (epoxy polyster) and vertical wire carrier 0.8

mm thick CRCA Finish powder coat (epoxy polyster)

89 Section 02 Desk Providing in place of main table with overall size of table equal to 1200 x 600 x750mm. The table is made of 25 mm thick 8 Nos 12570.30 1,00,562.40

Size - 3'6" x 2' Prelaminated Twin Board of E1-P2 grade edge banded with matching 2mm thick PVC lipping. Grommet provided on work surface

for wire manaement. The modesty panel is made of 25 mm thick Prelaminated Twin Board of E1-P2 grade. The understructure is

made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC

lipping. The HInge door unit is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded

with matching 2 mm thick PVC lipping. Handles are provided for ease of opening. Pedestals are provided with lock for security.

The product must be UL Greenguard certified.

90 Executive Chair The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat inner(material-polypropylene) with 1 Nos 19079.90 19,079.90

moulded polyurethane foam and polyster fabric. the net back should made up of back outer(material-glass fiber filled nylon) and back inner(material-PP)

and upholstered using polyester mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-51.0cm x (D)-

49.0cm. The supprot spine should made up of high pressure die cast polished aluminium. Armrest is having two adjustment, Height(6+/-0.5cm) and

depth(6+/-0.5cm). Height adjustment shall be provided in aluminium structure of armrest which is connected to aluminium back spine and is operated

with button. Armtop is made up of PU molded over plastic inner. The mechanism shall be Active BioSynchro Mechanism. The mechanism of chair shall

have following features:360 degree revolving type, Seat/Back tilt ratio of 1:2, Active Bio-Synchro mechanism, 5 position tilt limiter giving option of

variable tilt angle to the chair. Front-Pivot for tilt with feet resting on ground and continious lumber support should ensure more comfort. The

mechanism housing should made up of HPDC Aluminium and black powder coated. The chair shall be provided with pneumatic height adjustment which

shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished aluminium. it shall be fitted with 5 nos twin wheel castor. The size of

the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black

polypropylene. The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon) which is fixed to Aluminium back spine.

The neckrest assembly consists of upholstered neckrest inner(material-poly propylene) with moulded polyurethane foam and polyster fabric. upholstered

inner shall be fixed to neck rest cover. neckrest shall be fixed to back assembly through neckrest spline. Overall dimensions of Chair shall be, Width of

Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below. Height from ground - min 109.3 to max 124.4 cm. Seat height - min 45.5cm to

max 55.5cm. Dimensions tolerance / variations shall be within +/- 1 cm.

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

91 Workstation Chairs The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method described in OCP- 8 Nos 6873.03 54,984.24

QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat

shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia

2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be

upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 70.5 cm (H). The HR

polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25%

compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The mechanism shall be

designed with 360° revolving type, 17±2° maximum tilt m pivot at centre, Upright position locking., Tilt tension adjustment. The

pneumatic height adjustment shall has an adjustment stroke of 11.0 ±0.3cm. The bellow shall be 3 piece telescopic type and

injection moulded in Black Polypropylene. The pedestal shall be injection moulded in black 33% glass-filled Nylon66 and fitted

with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). The twin wheel castors

shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 43.3 to max 54.3cm, Height -

min99.5 to max 110.5cm, Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.

92 Visitor's Chairs The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method described in OCP- 2 Nos 5729.40 11,458.80

QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat

shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia

2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be

upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 60.5 cm (H). The HR

polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25%

compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The powder coated (DFT

40-60 microns) tubular frame shall be cantilever type & made of dia 2.54±0.03cm x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. Overall

Dimensions of Chair shall be Seat Height - 46.5cm, Height - 93.5cm, Width & Depth of Chair as measured from pedestal -Width-

61.0 cm and Depth-64.5 cm.

93 Full Height Cabinet Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal cladding of 0.8mm thk 1 Nos 89836.02 89,836.02

Size - 8' x 8' C.R.C.A (as per IS: 513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50±10 microns thickness.In case

of 2.5feet Height Storage units, wooden top is provided which is made of 25mm thick Pre-laminated board whereas 4.0feet and

4.5feet height Storage units are provided with 1 Imm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS: 513). The metal

tops are coated with Epoxy polyester powder of 50±10 microns thickness.

94 Full Height Cabinet Aesthetically appealing completely knock down construction.The add—on units are stack widthwise to form a row of storage 1 Nos 32511.24 32,511.24

Size - 8' x 2'6" having a common side panel. (Note— Single Main unit should not be offered.Minimum 1 Main + IAddon to be offered)Legs fitted

with screw typeleveler(add 45mm to the height).Made from combination of CRCA** 0.5 mm &

0.8mm Thickness.CRCA 'D' Grade as per IS-513 .

95 Top Cabinet Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal cladding of 0.8mm thk 1 Nos 112295.88 1,12,295.88

Size - 18'8" x 2'6" C.R.C.A (as per IS: 513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50±10 microns thickness.In case

of 2.5feet Height Storage units, wooden top is provided which is made of 25mm thick Pre-laminated board whereas 4.0feet and

4.5feet height Storage units are provided with 1 Imm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS: 513). The metal

tops are coated with Epoxy polyester powder of 50±10 microns thickness.

96 U.S CABIN 02 0.00

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

97 U.S Cabin 02 Desk Main Desk size shall be 1500 Width x 450 Depth x 750 Height. Top shall be made up of PVC membrane pressed of 25 mm thick 1 Nos 36662.94 36,662.94

Size - 5' x 2' MDF - one side laminate board with 0.4 mm PVC membrane Pressed on to tops. The top shall be having duck nose and half round

profile edges and top is made in only one finish which is European Ash.

98 Executive Chair The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat inner(material-polypropylene) with 1 Nos 17171.91 17,171.91

moulded polyurethane foam and polyster fabric. the net back should made up of back outer(material-glass fiber filled nylon) and back inner(material-PP)

and upholstered using polyester mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-51.0cm x (D)-

49.0cm. The supprot spine should made up of high pressure die cast polished aluminium. Armrest is having two adjustment, Height(6+/-0.5cm) and

depth(6+/-0.5cm). Height adjustment shall be provided in aluminium structure of armrest which is connected to aluminium back spine and is operated

with button. Armtop is made up of PU molded over plastic inner. The mechanism shall be Active BioSynchro Mechanism. The mechanism of chair shall

have following features:360 degree revolving type, Seat/Back tilt ratio of 1:2, Active Bio-Synchro mechanism, 5 position tilt limiter giving option of

variable tilt angle to the chair. Front-Pivot for tilt with feet resting on ground and continious lumber support should ensure more comfort. The

mechanism housing should made up of HPDC Aluminium and black powder coated. The chair shall be provided with pneumatic height adjustment which

shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished aluminium. it shall be fitted with 5 nos twin wheel castor. The size of

the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black

polypropylene. The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon) which is fixed to Aluminium back spine.

The neckrest assembly consists of upholstered neckrest inner(material-poly propylene) with moulded polyurethane foam and polyster fabric. upholstered

inner shall be fixed to neck rest cover. neckrest shall be fixed to back assembly through neckrest spline. Overall dimensions of Chair shall be, Width of

Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below. Height from ground - min 109.3 to max 124.4 cm. Seat height - min 45.5cm to

max 55.5cm. Dimensions tolerance / variations shall be within +/- 1 cm.

99 Visitor's Chairs The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method described in OCP- 2 Nos 6873.03 13,746.06

QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat

shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia

2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be

upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 60.5 cm (H). The HR

polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25%

compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The powder coated (DFT

40-60 microns) tubular frame shall be cantilever type & made of dia 2.54±0.03cm x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. Overall

Dimensions of Chair shall be Seat Height - 46.5cm, Height - 93.5cm, Width & Depth of Chair as measured from pedestal -Width-

61.0 cm and Depth-64.5 cm.

100 2 Seater Sofa Set Providing and placing in position of 2 seater sofa. The overall dimensions of the sofa shall be 1460W x 905D x 855H. The seat 1 Nos 27073.62 27,073.62

should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2

kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density

28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or

leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and

termite proof as per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm

dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should be a welded assembly made in

Stainless steel (grade SS 202) tube & plate with plastic endcap.Complete all as per the direction of Engineer in Charge.

101 SUPPORT STAFF

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

102 Support Staff Seating Table - T 101 size shall be 1199 Width x 590 Depth x 750 Height . The top panels shall be made from 18 +/- 0.5 mm thick Pre - 1 Nos 13410.63 13,410.63

Table laminated boards as per with 2 mm thick PVC edge banding on all sides . Understructure shall be made from 0.9 mm +/- 0.09 mm

Size - 4' x 2' thick powder coated 50 microns (+/-10) CRCA MS. Tubular Frame shall be sq. 25.4 +/- 0.3 mm x 1.2 +/- 0.096 mm thick MS ERW

tube .Modesty panel shall be made from 1.0 +/- 0.09 mm thick powder coated 50 microns (+/- 10). The Storage shall be having

shell 0.5 +/- 0.07 mm thick CRCA MS plus drawer tray 0.5 +/- 0.07 mm thick CRCA MS plus drawer front 0.8 +/- 0.1 mm thick CRCA

MS . Also there should be 10 lever cam lock plus handles built in plastic

103 Support Staff Chairs The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method described in OCP- 4 Nos 6873.03 27,492.12

QLTA-P14-18 and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat

shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia

2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be

upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 70.5 cm (H). The HR

polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25%

compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The mechanism shall be

designed with 360° revolving type, 17±2° maximum tilt m pivot at centre, Upright position locking., Tilt tension adjustment. The

pneumatic height adjustment shall has an adjustment stroke of 11.0 ±0.3cm. The bellow shall be 3 piece telescopic type and

injection moulded in Black Polypropylene. The pedestal shall be injection moulded in black 33% glass-filled Nylon66 and fitted

with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). The twin wheel castors

shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 43.3 to max 54.3cm, Height -

min99.5 to max 110.5cm, Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.

105 Low Height Cabinet Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal cladding of 0.8mm thk 1 Nos 89836.02 89,836.02

Size - 15'6" x 2'6" C.R.C.A (as per IS: 513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50±10 microns thickness.In case

of 2.5feet Height Storage units, wooden top is provided which is made of 25mm thick Pre-laminated board whereas 4.0feet and

4.5feet height Storage units are provided with 1 Imm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS: 513). The metal

tops are coated with Epoxy polyester powder of 50±10 microns thickness.

106 Full Height Cabinet Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal cladding of 0.8mm thk 1 Nos 134753.13 1,34,753.13

Size - 11' x 8' C.R.C.A (as per IS: 513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50±10 microns thickness.In case

of 2.5feet Height Storage units, wooden top is provided which is made of 25mm thick Pre-laminated board whereas 4.0feet and

4.5feet height Storage units are provided with 1 Imm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS: 513). The metal

tops are coated with Epoxy polyester powder of 50±10 microns thickness.

107 Low Height Cabinet Aesthetically appealing completely knock down construction.The add—on units are stack widthwise to form a row of storage 2 Nos 22892.31 45,784.62

Size - 6'6" x 2'6" having a common side panel. (Note— Single Main unit should not be offered.Minimum 1 Main + IAddon to be offered)

Legs fitted with screw type leveler

(add 45mm to the height)

109 Pantry Chairs 4 nos 4752.00 19,008.00

Digitally signed by RAHUL

BOQ FURNITURE WORKS 5TH FLOOR PESB

110 Bottom Cabinet size- 9'x Aesthetically appealing completely knock down construction. The add—on units are stack width wise to form a row of storage 2 nos 19004.40 38,008.80

2'6"x 2'6" having a common side panel. (Note— Single Main unit should not be offered. Minimum 1 Main + IAddon to be offered)

Legs fitted with screw type leveller

(add 45mm to the height)

111 JC Cabinet Janitor Cupboard made up of 20/22gauge CRCA sheets duly enamel painted finish

112 Material Mild Steel 1 Nos. 16154.10 16,154.10

No. Of Shelves 3 Shelves

No. of Doors 2 Doors

Mount Type Wall Mount

Door Type Hinged

Height (in Feet) 6

Dimension ( L*W ) 3X1.5

Usage/Application Office

113 Top Cabinet Aesthetically appealing completely knock down construction.The add—on units are stack widthwise to form a row of storage 1 Nos 27236.43 27,236.43

Size - 7' x 2'6" having a common side panel. (Note— Single Main unit should not be offered.Minimum 1 Main + IAddon to be offered)Legs fitted

with screw typeleveler(add 45mm to the height).Made from combination of CRCA** 0.5 mm &

0.8mm Thickness.CRCA 'D' Grade as per IS-513.

Digitally signed by RAHUL