SPECIAL REPAIR TO BUILDING NO T-107 AT DAMANA UNDER GE JAMMU

Amount

Taking down chowkats or frames with shutter w/o taking off shutter from the frame n.exc 1.5 sqm each incl cutting holes for taking out hold fast or dismantling brick (holes cut and any other damage to jambs, wall for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) all as specified and directed.

Taking down chowkats or frames with shutter w/o taking off shutter from the frame exc 1.5 sqm but n.exc 4 sqm each incl cutting holes for taking out hold fast or dismantling brick (holes cut and any other damage to jambs, wall for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) all as specified and directed.

Taking down shutters only of any description exceeding 1 sqm but not exceeding 2 Sqm each complete all as specified and as directed by the Engineer in Charge

Demolition of cement concrete (unreinforced) in ground floors and paving's n.exc 15 cm thickness (below or above ground level) and removing unserviceable material exc 100 mtr as specified.

Demolition of reinforced cement concrete of any description and in any position complete all as specified and as directed by the Engineer in Charge.

Demolition of RCC (other then ground floor) beam landing, chajjas slabs sleves, kitchen chimni & similar suspended work and removing unserviceable material exc 100 mtrcomplete all as specified and as directed by the Engineer in Charge.

Demolition of brick work built in cement mortar or cement lime mortar incl all quoins, arches pillars etc and removing unserviceable material exc 100 mtr as specified complete all as specified and as directed by the Engineer in Charge.

Racking out joints / pointing to brick work in walls or to bricks on edge in floors, surface channels, roofs etc complete all as specified and as directed by the Engineer in Charge.

Taking down cement plaster of any description on brick or stone walls or from concrete surface incl racking out joints hacking for key scrubbing with water etc complete all as specified and as directed by the Engineer in Charge.

Dismanting asbestos cement (corrugated or semicorrugated etc) sheets in roof covering complete all as specified and as directed by the Engineer in Charge. .

Dismantling ceilling boarding of any type and description incl cover fillets complete all as specified and as directed by the Engineer in Charge.

Dismantling floors hearth or wall tilling including cement mortar bedding (but not backing) removing serviceble tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer in Charge.

Dismantling of PVC ,cast iron 100mm or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches, if required complete all as specified and as directed by the Engineer in Charge.

Dismantling of PVC ,cast iron 75mm or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches, if required complete all as specified and as directed by the Engineer in Charge.

Dismantling of PVC ,cast iron 50mm or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches, if required complete all as specified and as directed by the Engineer in Charge.

Takind down GI tubing of 15 mm bore and connection and incl cleaning for refixing or removel complete all as specified and as directed by the Engineer in Charge.

Takind down GI tubing of 20 mm bore and connection and incl cleaning for refixing or removel complete all as specified and as directed by the Engineer in Charge.

Dismantling/disconnecting/demolition of water storage tank of any type or description (RCC/PVC/Bricks etc) exc 250 and n.exc 500 Ltrs capacity and removing from site or refixing in position complete all as specified and as directed by the Engineer in Charge.

Pressed steel frames for door (Factory made) out of 1.25 mm thick black MS sheet, with one or more rebates including necessary fixing lugs, butt hinges, lock strike plate, etc. complete, size of frame 105x60mm incl bottom of each chowkat to be welded with 2 Nos 25x25x3 mm thick flat iron projecting 10 cm on either side and back fill to chowkats with PCC 1:3:6 type C0 using 12.5 mm graded crushed stone aggregate including one shop coat of red oxide primer complete all as specified and directed. Note:- PCC 1:3:6 type C-0 using 12.50 mm graded crusheed aggregate as in back fill will measured and paid separately.

Pressed steel frames for door (Factory made) out of 1.25 mm thick black MS sheet, with one or more rebates including necessary fixing lugs, butt hinges, lock strike plate, etc. complete, size of frame 125x60mm incl bottom of each chowkat to be welded with 2 Nos 25x25x3 mm thick flat iron projecting 10 cm on either side and back fill to chowkats with PCC 1:3:6 type C0 using 12.5 mm graded crushed stone aggregate including one shop coat of red oxide primer complete all as specified and directed. Note:- PCC 1:3:6 type C-0 using 12.50 mm graded crusheed aggregate as in back fill will measured and paid separately.

Solid PVC door frame of size 50mm x 47mm made out of 5mm plain coloured PVC sheet, reinforced with MS square tube supplying and fixing in opening as per specification and drawing and as per sample kept in office of GE Jammu.

35 mm thick Flush Shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

35 mm thick 2nd class hard wood factory made glazed and Skelton shutters open rebated and prepared to receive glass/wire gauge etc. without sash bar but with lock rail edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass/wire mesh etc sizes of member as per clause 8.20(a) of SSR part -I for door shutter complete all as specified and as directed.

18/19 mm thick prelaminated particle board interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber frame work as in cupboard shelves/pelmet box including teak wood beading all around all as specified & directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing in SSR Part -II and as per sample kept in GE office complete all as specified and as directed..

Steel window 1.25 mm thick Box type (primer coated) ERW hollow P section of size 60 mm x 25 mm single rebated comprises glazed skelton shutter ERW sec 50 mm x 20 mm and 1 mm thick with two Nos sash bar of T- section 20 mm x 3 mm complete welded to frame with one vertical mullion of ERW box type T- section of size 60 mm x 25 mm and 1.25 mm thick including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 four No for each window incl following fitting welded to frame shutter hold fast of 150 mm long of 12 mm x 3 mm FI made to shape 4 No, handle of Z section 20 mm x 25 mm x 100 mm long 1 No per leaf, MS tower bolt 150 mm long 2 No per leaf, Z sec 20 mm x 25 mm, 100 mm long stopper 1 No on per leaf, MS Pintal hinges of size 75 mm x 12 mm 2 No per leaf fabrication and fixing arrangement as per drg No CEPZ/TD-324,325/07.

Steel window 1.25 mm thick Box type (primer coated) ERW hollow P section of size 60 mm x 25 mm single rebated comprises wire gauged skelton shutter ERW sec 50 mm x 20 mm and 1 mm thick with two Nos of FI section complete welded to frame for holding wire mesh with one vertical mullion of ERW box type T- section of size 60 mm x 25 mm and 1.25 mm thick including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 four No for each window incl following fitting welded to frame shutter hold fast of 150 mm long of 12 mm x 3 mm FI made to shape 4 No, handle of Z section 20 mm x 25 mm x 100 mm long 1 No per leaf, MS tower bolt 150 mm long 2 No per leaf, Z sec 20 mm x 25 mm, 100 mm long stopper 1 No on per leaf, MS Pintal hinges of size 75 mm x 12 mm 2 No per leaf fabrication and fixing arrangement as per drg No CEPZ/TD-324,325/07 complete all as specified and as directed.

Mild steel works of flat iron, square bar, round bars etc. as in framed work such as grills, guard bars, gratings etc incl bending, cutting and welding as necessary of confirming to Gde Fe 290-0 including one shop coat of red oxide primer complete all as specified and as directed.

Galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tacks or galvanized wire staples complete all as specified and as directed.

3 mm thick sheet glass ordinary quality glazing with steel pins,oil putty to steel windows and, beads nails etc to wooden surfaces as in square exc 0.50 sqm in each pane, complete all as specified and as directed.

3 mm thick figured glass, frosted head type and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and as directed.

MS butt hinges 100mm long medium weight cold rolled complete all as specified.

Aluminium anodized barrel tower bolt 150 mm long of extruded section complete all as specified.

Aluminium anodized handle fabricated type 150mm long complete all as specified.

MS butt hinges 50mm long medium weight cold rolled complete all as specified.

Mild steel helical/ordinary rat tail rod pattern door spring 300 mm including roller and roller plate complete fixed with welding complete all as specified and as directed.

Aluminium alloy, anodised,sliding door bolt 300 mm long with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloycomplete all as specified and as directed.

100 mm long hasp and staple, aluminium anodixed with bolt to hinge palte and fixed with screws complete all as specified and as directed.

PCC 1:2:4 type B 1 using (20 mm graded aggregate) as in blocks for hold fasts,lintels upto 1.5m clear span, benching, coping apex stones, bed plates and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and as directed. Note: Form work required for these items included in the unit rate of this item.

Non skid ceramic coloured tiles 7 to 8mm thick (square /rectangulament ) area of each tile exeeding 0.06 but not exceeding 0.11 sqm, in floors,including roughening old surfaces over 15 mm thick screed in CM 1:6 set and jointed in neat cement slurry and pointed in white/coloured cement with pigment to match complete all as specified and as directed.

Non skid ceramic coloured tiles 7 to 8mm thick (square /rectangulament ) area of each tile exeeding 0.11 but not exceeding 0.18 sqm, including roughening old surfaces of floors, over 15 mm thick screed in CM 1:6 set and jointed in neat cement slurry and pointed in white/coloured cement with pigment to match complete all as specified and as directed.

Glazed ceramic coloured tiles 300x 200x 7 mm thick on skirting, dado set and jointed in neat cement slurry and pointed in white cement with pigment to match the surface over 10 mm thick screed in CM 1:6 complete all as specified and as directed.

Green Marble work 18 to 20 mm thick (table rubbed and polished ) in stapes jambs, pillars, window cill, cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15 mm thick screed in CM 1:6 set and jointed in neat cement slurry and pointed in white/coloured cement with pigment to match complete all as specified and as directed.

Rendering 15 mm thick in CM 1:4 on fair face of brick work surfaces finished even and smooth with out using extra cement complete all as specified and as directed.

Rendering 15 mm thick in CM 1:6 on other than fair face of brick work surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 5 mm thick cement plaster 1:4 on fair faces of concrete surfaces as in ceiling, chajja, shelves etc. finished even and smooth without using extra cement complete all as specified and as directed..

Rendering 15 mm thick cement plaster 1:3 on other then fair faces of concrete surfaces as on fascia of roof slab, chajja, shelves etc. finished even and smooth without using extra cement (incl all necessary scaffolding, lifting arrangment for three story building on external surfaces) complete all as specified and as directed.

Rolled structrual steel work as in rafters, purlins, where connected to common rafters and running rails fixed with angle cleats or other connecting plates, wind ties for roof etc incl painted with and incl one coat of primer Fe-410- W(Gde- E-250) quality -B complete all as specified and as directed.

Plates (plain or chequered channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe-410- W(Gde- E-250) quality -B complete all as specified and as directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 22.5cm and n exc 30cm long, Diameter of neck 16mm to 20mm complete all as specified and as directed.

Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

4mm thick of size 605X605 mm ,White pre-premiered, self embossed, Reinforced Designer Board for false ceiling Conforming to IS-14862 and ISO-8336:1993. As per following specification : (i)GI section frame work (POWDER COATED) for white, pre-premiered, self embossed, reinforced designer board consisting of perimeter wall angle 19mmX19mmX0.45mm, cross 'Tee' 28.6mm (web)X 24mm flange .33mm thick powdered coated main tee 38(Web) X24mm flange 0.33mm thick. wall angle screwed fixed to brick wall/partition wall/concrete/RCC with the help of nylon sleeves and screws @ 610 mm C/C , Then suspending GI main 'Tee' in both directions by means of hangers with alignment @ 1220mm C/C to soffits. To form grid of 610X610mm cross Tee shall be provided @ 610mm C/C in both directions. Suitable provisions shall be made for fixing the recessed/surface mounting light fittings if any, complete all as specified and directed by Engr-in-Charge.

PVC (SWR) pipes 110 mm bore double socketed, in any length with rubber ring joints, fixed to walls complete all as specified.

PVC (SWR) pipes 75 mm bore double socketed, in any length with rubber ring joints, fixed to walls complete all as specified.

PVC (SWR) bends 110 mm bore any radius complete all as specified.

PVC (SWR) bends 75 mm bore any radius complete all as specified.

PVC (SWR) 'P’ trap 110/110 mm bore complete all as specified.

PVC (SWR) 'S' trap 110/110 mm complete all as specified.

PVC (SWR) floor trap 75mm, plain with grating including jointing with solvent cement complete all as specified.

WC Orissa pattern white with integral foot rest 580 x 440 mm fixed in repair including PCC bedding 1:2:4 and making good disturbed floor connecting to trap and flush pipe complete all as specified.

Vitreous China wash basin, white, flat back, size 580x450 mm including 32 mm dia PVC waste pipe, CP brass waste coupling 32 mm dia, pair of MS brackets or MS fastener/bolts for fixing arrangements and 450 mm long PVC connection with PVC nut and washer fixed in repair complete at site and all as directed.

PVC low level flushing cistern 10 Ltr capacity white with inlet ball value, float valve and handle inc brackets, PVC flush pipe complete all as specified and as directed.

Pillar taps 15 mm dia, cast copper alloy, with capstan heads, chromium plated fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed suitable for 15 mm bore fixed in repair complete all as specified.

Bib tap cast copper alloy with crutch or butterfly handle, chromium plated fancy type screwed for iron pipe, suitable for 15 mm bore fixed in repair complete all as specified.

Stop valve cast copper chromium plated concealed type screwed down high pressure with capstan head suitable for 15 mm bore fixed in repair complete all as specified.

Stop valve/angle valve cast copper chromium plated screwed down high pressure with capstan head suitable for 15 mm bore, screwed both ends for iron pipe fixed in repair complete all as specified.

Stop valve 20 mm dia cast copper alloy, secrewed down high pressure with crutch or butterfly handle secrewed both ends for iron pipe and fixed fixed in repair complete all as specified.

Brass chromium plated shower rose 125 mm size swivel type with connecting rod 15 mm bore fixed in repair complete all as specified and as directed.

Stainless steel gratings of outer frame dia 150 mm open able type incl all necessary fitting such as hinges including embedding in tiles with white cement complete all as specified and as directed.

PVC connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipes of 15 mm bore complete all as specified and as directed.

15 mm bore galvanised pipe medium grade with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

20 mm bore galvanised pipe medium grade with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Fixing only 15 mm dia old galvanised pipes incl new fittings where necessary fixed complete to wall and ceiling or laid in floor complete all as specified and as directed.

Fixing only 20 mm dia old galvanised pipes incl new fittings where necessary fixed complete to wall and ceiling or laid in floor complete all as specified and as directed.

Cutting chases for concealed water tubing or concealed conduit & making good in CM 1:3 of grith exc 10 cm and n.exc 20 cm in brick wall complete all as specified and as directed.

Rotational moulded polythylene water storage tank with float valve, plastic lid cover, triple layered, cylindrical verticl with closed top hoisted and fixed in position of capacity 500 Ltr incl making connections complete all as specified and as directed.

Preparation of surface of sunken slab and applying 15mm thick plaster in cement morter 1:4 mixed with water proofing compound both on floor and wall @ 200ml per 50 Kg bag of cement and apply Epoxy Resin coating with modified cementtition coating like Brush Bond of Fosroc/Pedilite/Bostic as per manufacture instruction both on floor and wall complete all as specified.

Supply only integral liquid water proofing admixture of approved make all as specified.

Stainless steel kitchen sink with drainage board made of stainless steel of 1 mm thick sheet including plugs, washers and pvc waste pipe of 40 mm dia. Fixing with complete on appropiate size of cantilever brackets of MS angle or GI pipe 15 mm dia with proper arrangment to hold and fitting of sink complete all as specified and directed at site and connecting union to pipe. The overall size of sink 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified and as directed by the Engineer in Charge.

Preparation of new plastered surfaces and applying two coats of white wash on walls complete all as specified and as directed by the Engineer in Charge.

Preparation of old plastered surfaces and applying two coats of white wash on walls complete all as specified and as directed by the Engineer in Charge.

Preparation of new plastered surfaces and applying two coats of white wash on ceilings complete all as specified and as directed by the Engineer in Charge.

Preparation of old plastered surfaces and applying two coats of white wash on ceilings complete all as specified and as directed by the Engineer in Charge.

Preparation of new plastered surfaces and applying two coats of oil bound distemper on walls over a coat of chalk whitening complete all as specified and as directed by the Engineer in Charge.

Preparation of old plastered surfaces and applying two coats of oil bound distemper on walls complete all as specified and as directed by the Engineer in Charge.

Preparation of new plastered surfaces and applying two coats of cement base paint on walls over a coat of chalk whitening complete all as specified and as directed by the Engineer in Charge.

Preparation of old plastered surfaces and applying two coats of cement base paint on walls complete all as specified and as directed by the Engineer in Charge.

Preparation of new steel surface exc 10cm width or girth and applying two coats of synthetic enamel paints over priming with red oxide complete all as specified and as directed.

Preparation of new wood or wood based surface and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and as directed.

50 mm thick PCC 1:2:4 750 mm wide, laid to an outward slope of not less than 1:12, cast in panels not exceeding 2.00 SM areas with 6mm wide joints. The joint shall be filled with mastic filling and 10 mm wide Joints between the walls and plinth protection shall be filled with mastic filling complete all as specified.

MS PVC caoted drapery rods of 25 mm dia complete with coloured conical end balls at both end, dia not less then 50mm and fitted with and incl MS PVC sheeted/powder coated bracket size 150mm made to shape or 75mm dia PVC/PVC Coated coloured end wall to wall round block made to shape in male and female pieces as required complete all as specified and as directed.

Plain aluminium sheeting 0.56 mm thick as in cover of crumple section and fixed to wall and roof with screws complete all as specified and as directed.

E&M PORTION:- Taking down carefully unsv aluminium / copper conductor point wiring (light, fan, light socket, power socket) complete fitting such as swithes, sockets, lamp holder, utility light fitting, fan regulator etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and as directed.

Taking down carefully unsv main switch / DBs alongwith MCBs / wooden board / connected fittings & fixtures any type and making good distrubed surface of walls and roofs to match the existing surface, complete all as specified and as directed.

Point wiring with 1.5 Sqmm single core multi stranded copper conductor FRLS insulated and unsheathed heavy duty cable in colour code including contineous earth wire with cable of size 1.5 sqmm copper conductor flexible FRLS insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked 25mm dia terminated into CI/pressed steel terminal boxes including 3.00mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etc for one light/fan/bell point controlled by one, one way switch including cutting chases and making good to disturbed surfaces of wall / ceiling / floor including treating with existing finishes, complete all as specified and as directed.

Description all as per item No.97 above but for 3 Pin socket outlet 5 Amps point on independent board with PVC insulated copper conductor cable 1.5sqmm complete all as specified and directed.

Description all as per item No.97 above but for one bell / buzzer point controlled by one 5 Amp switch complete all as specified and directed.

Description all as per item No.97 above but for 3 Pin socket outlet 5 Amps point on same board with PVC insulated copper conductor cable 1.5sqmm complete all as specified and directed.

Description all as per item No.97 here in before but for 3 Pin socket outlet 15 Amps point on independent board other switches with with PVC insulated copper conductor cable 2.5sqmm 1100 Volts grade, complete all as specified and directed.

Description all as per item No. 97 here in before but for 3 Pin socket outlet 15 Amps controlled by two way switch with PVC insulated copper conductor cable 1.5sqmm 1100 Volts grade, complete all as specified and directed.

Socket outlet multipurpose combination 2 in 1, 5 Amp flush type universal, complete all as specifed.

Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Self ballast LED retro fit lamp with PVC body and PC diffuser 9 watt 230 volt 6500k complete all as specified and directed.

Switch piano flush type 5 Amp single pole one way, (ISI marked), complete all as specified.

Socket outlet multipurpose combination 3,5 pin 15 Amp shuttered type, complete all as specifed.

Bell push piano flush type 6 Amp, (ISI marked), complete all as specified.

Calling bell Ding Dong type, fixed in repair complete all as specified. .

Sheet metal enclosure factory made phosphatised, powder painted MCB DBs, 240 volts, 8 way without bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning, complete all as specified.

Ceiling rose (ISI Marked) 3 terminals PVC/poly carbonate, insulated body, compete all as specified.

Supply and fixing in replacement New generation energy saving,wall mounted LED Tube light fitting 20 watt wall mounted LED batten rod extruded aluminium heated sink provided for efficient heat dissipation and integrated electronic driver 20 watt LED 6500 k (4 feet long) with LED rod of 20 watt , complete all as specified.

Supply and fixing in replacement MCB single pole and neutral 32 amps 240 volts fixing in replacement, complete all as specified and directed.

MCB triple pole and neutral 63amps 415 volts 50 Hz, B 'series ' 10 KA breaking capacity, complete all as specified.

Sheet metal enclosure factory made (Double door) for DBs, Triple pole and neutral, 240 volts, 4 way with 200 Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning, complete all as specified.

MCB single pole and neutral 6-32 amps 240 volts fixing in replacement, complete all as specified and directed.

Earthing complete with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh, 40mm dia bore light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection pipe, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion. Note:- Rate for earth lead wire & protection pipe upto 7.5mtr length are inclussive in this item & no extra payment shall be admissible for the same.

Mehta Enterprises

M/S STAR CONSTRUCTIONS

M/s Sekinder Paul Sharma

Jagbir Singh and Co

Kanwal Nain Behl