Construction of Market Shed at Boro Bazar under 5th ASFC 2019-20

Amount

Plain cement concretre floor base in prop 1:3:6 laid in alternate bays as specified with course aggregate at size 13mm to 32mm including dewatering if necessary and curing complete. c) 100 mm thick

Providing and laying 25 mm thick DPC with CC in prop 1:1:5:3 with graded stone agg. Of 10 mm down nominal size including providing approved damp proof admixture in prop as recommended by the manufacture including curing etc. complete as directed.

REINFORCED CEMENT CONC WORK Providing and laying plain/reinforcement cement concrete works in prop 1:2:4( 1 cement : 2 coarse sand :4 coarse aggregate 20mm down ) including dewatering if necessary and curing compelete but excluding cost of from work and reainforcement for reainforced cement concrete work. (from work and reainforcement will and be measured and paid separately) (i) Using mixture machine (A) In sub-structure upto plint level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank not less than 100mm thick plinth level. (N) Without using admixture, plasticser c) M 25 grade concrete

(B) In super structure from plinth level up to 1st floor level. ii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, linte; sill band, beam, girder, bressumer, cantilever, staircase (except sprial staircase and landing) including preparing the top surface and finishing or nosing. (N) Without using admixture, plasticser c) M 20 or Prop. 1:1.5:3

SHUTTERING AND FORWORK PLYBOARD SHUTTERING (FORMWORK) Providing from work of 12mm thick plywood Board so as to give a rough finish including etc. height of proping and centering below supporting floor supporting floor to ceiling not exeeding 4.0M and removal of the same for situ reinforced concrete and plain concrete works in: Foundation, footings, base of columns, pile cap etc., (b) Using 25mm thick plank

Sides of tie beams, grade beams etc., (b) Using 25mm thick plank

Columns, pillars, Post & Strut b) Circular or curved in plan (Using 38mm thick plank)

PLYBOARD SHUTTERING (FORMWORK) Providing from work of 12mm thick plywood Board so as to give a rough finish including etc. height of proping and centering below supporting floor supporting floor to ceiling not exeeding 4.0M and removal of the same for situ reinforced concrete and plain concrete works in: Columns, pillars, Post & Struts of square/ rectangular/ polygonal in plan or any shape like Tee/ L etc. having plane vertical face.

Sides and Soffits of Beams, beam haunchings, cantilever griders, bressumers, lintels and horizental ties. A) For depth not exeeding 1.0M

MASONRY WORKS BRICK WORKS: Providing brick soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to lavel and in pael after preparing the sub grade as directed including all labours and materilas and if necessary dewatering complete. a) Brick on flat soling

Brick work in cement mortar with 1st class brick including racking out joints and curing complete as directed. (I) In sub-structure upto plinth level including dewatering if necessary. (b) In proportion 1:6

1st class brick nogged wall in cement mortar in racking out joint and caring complete as directed in super structer above plinth upto 1st floor level. (a) 112mm thick brick wall (b) In cement mortar in proportion 1:4 (1 cement : 4 sand )

FLOORING AND FLOORING FINISHING CEMENT CONCRETE FLOORING 65 mm thick cement concrete floor consisting of 50 mm under layer of cement concrete in prop. 1:3:6 (1cement :3 coarse sand :6 coarse aggregate of 25mm and down) and 15mm thick waering layaer in cement concrete in prop. 1:1:2….. Includimh curing etc. complete as directed.

PLASTERING WORK 10mm thick cement plaster in single coat on rough side of brick/concrete walls for interior plastering up to 1st floor level including arises or rounded angles not execeeding 80mm girth and finished even and smooth including curing complete as directed. (b) In cement 1:4

15mm thick cement plaster in single coat on rough side of brick/concrete walls for interior plastering up to 1st floor level including arises or rounded angles not execeeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side. (c) In cement 1:4

Extra over item no. 6.2.1 to 6.2.3 for plastering on celling and soffits of stairs upto 1st floor level (instead of plastering on walls) including curing complete as directed.

CEILLING, LINING AND PARTITION BISON PANEL CELING AND PARTION Providing, fitting and fixing in position false ceiling of 6mm thick Bison panel (cement bonded particle board) on timber frame of 1st class local wood (Hollock/ Bonsum/ Sundi) of 50mm × 50mm spaced at not more than 1.20m a part, fixed to the wall at the end with necessary nails, wood screws, hooks, botls etc.. as directed by the Department for all levels. (a) Both sides commercial

ROOFING Providing Pre Painted Galvanized Iron Sheet Roofing (PPGI) at all levels including fitting and fixing with self driling, self tapping screws complete. (Roof trusses, purlins etc. to be measured and paid serparately) Dyna roof/ Wonder Roof/ JSW Steel/ Specturm or equivment as directed by the Department. (ii) 0.50 mm thick

Providing Pre Painted Galvanized Iron Sheet Roofing (PPGI) accessories (Ridges/ Valley/ Gutter/ Flashing) at all levels including fitting and fixing with self driling, self tapping screws complete. Dyna roof/ Wonder Roof/ JSW Steel/ Specturm or equivment as directed by the Department. (iii) 0.50 mm thick

WOOD WORKS Providing wood work in frame of false ceiling partitions etc. sawn, wrought, framed hoisted and fixed in position with spikes, nails, M.S flat, angle/cleats with bolt and nuts complete including kircide oiling two coats to unexposed surfaces of the timber (M.S flat, angle cleats, and bolt and nuts required for flat, angle cleats wherever necessary shall be measured and paid separately) b) With Gamari/Bonsum/Sundi

m) Distempering two coas with oil bound distemper of approved brand and manufacture and of required shade on new wall surface to give and even shade over and including a priming coat with ditemper primer of approved brand and manufacture after throughly brooming the surface free from throughly brooming the suface free from mortar droppings and other foreign matter and including preparing surfaces even and sand pepered smooth. (i) Painting coat with distemper primer

(ii) Top coat

Providing two coats of J.K Wall Putty (White Cement based for concrete/mortar walls and ceilling both internal and external) after removing all lossely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm)

Finishing old/new wall surface after cleaning and cleaning the surface etc. including scaffolding complete as directed at all levels (two coats)

Applying priming coat over new wood and wood; based surfaces over 100mm in girth / width after and including preparing the surface by througly cleaning oil, grease, dirt and other foriegn matter, sand papering and knotting a) With ready mixed paint, wood primer (pink)

Painting two coats (excluding priming cat) on new wood and wood based surfaces with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ICICI paint/ J & N Pint/Nerolac) to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matter sand papering and stopping. a) Surface over 100mm in width or girth i) General purpose (Asian paint/ Berger paint/ ICICI paint/ J & N Paint/Nerolac)

PAINTING ON STEEL AND OTHER METAL SURFACES Applying primary coat over new steel and other metal suface over 100mm in with or girth after preparing the surface by throughly claening oil, grease,dirt and other foreign mater and scoured with wire brushes, fine steels, wood scapers and sand paper. a) With ready mixed "red-lead/red-oxide" primer.

Painting two coats (excluding priming cat) on new wood and wood based surfaces with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ICICI paint/ J & N Pint/Nerolac) to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matter sand papering and stopping. a) Surface over 100mm in width or girth i) General purpose (Asian paint/ Berger paint/ ICICI paint/ J & N Paint/Nerolac)

STEEL & IRON WORKS Supplying, fitting and fixing in position reainforcement bars conforming to relavent I.S. Code for R.C.C work/R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs spacers etc. complete. B) Other ISI approved TMT reinfocement bar (SAI/BISCON/THERMAX

Providing, fitting , hoisting and fixing of roof trusses fabrication out of combination of any two or all of the folowing sections (i) Squre section (ii) Rectangular Hollow section of specification RSH/SHS nad (iii) M.S. circular hlollow section of Grade 210.....M.S. cleats, base plates, bolts and nuts etc. as directed as per specifications b) Using other ISI marked approved circular hollow section

Providing and fixing in position collapsible M.S. shutters with vertical channels 20mm×10mm×2mm braced with flat iron diagonals… including applying a priming coat of red lead paint.

PLINTH PROTECTION WORKS AND DRAINS Providing plinth protection with bricks flat laid in cement mortar 1:4 and finishing with 15mm thick cement plaster in prop. 1:2 with a floating coat of neat cement finish.

Providing drain with brick work in cement mortar in prop. 1:5 with half brick thick side walls and 100 mm thick CC (1:3:6) base over one brick flat soling including 15mm thick cement plastering in prop. 1:3 finishing with a floating coat of cement slurry as directed with necessary shuttering for sides and earth work in excavation of foundation trances and refilling the sidesn after completion of work etc. as specified. i) 300mm wide and average 150mm deep with bed slope in 150 with intial depth of 100mm.

ANTI TERMITE TREATMENT Pre contruction anti-termite treatment at the bottom of foundation pits and walls on either side up to a height of 300mm from bottom of the excavation made for column plinth beam, wall, trenches etc. by applying the emulsion @ 5 (five) litres per square meter of the surfaces area before starting construction work (supplying of necessary tools and accessories by the contractor) as per the direction of the department complete. a) With aqueous emulsion having concentration 1:19 with chloropirophose solution (tricl or equivalent) and water, i.e 1% solution.

CONSTRUCTION OF ASSAM TOILET BLOCK AT DETAILS ESTIMATE OF CIVIL WORKSEARTHWORK IN EXCAVATION: Earth work in excavation for foundation, trenches of walls, retaining walls, footing, columns, steps and septic tank etc. Including refiling (return filling) the quantity as necessary after complete of work, breaking clods in return filling dressing, watering and ramming etc and removal of surplus earth with all lead & lift as directed and specified in following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00 below the existing ground level. (a) In ordinay soil.

Earth/ Sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming, etc complete as directed and specified. Including payment of land compensensation, Forest Royalty, Sales Tax and other duties an d taxes as may be necessary , (C) With river sand or silt (predominently non plastic) by truck carriage including loading and unloading.

Plain cement concretre work with course aggregate at size 13mm to 32mm in foundation bed for footing steps, walls brick work etc. as directed and specified including dewatering if necessary and curing complete(Shuttering works where necessary shall be measured and paid separtely) a) In prop 1:3:6 (1cement: 3sand:6 coarse aggregate ) by volume

Plain cement concretre work with course aggregate at size 13mm to 32mm in foundation bed for footing steps, walls brick work etc. as directed and specified including dewatering if necessary and curing complete(Shuttering works where necessary shall be measured and paid separtely) b) In prop 1:4:8 (1cement: 4sand:8 coarse aggregate ) by volume

Providing and lying 25mm thick damp proof course concrete with cement in prop. 1:5:3 with graded stone agg. Og 10mm down nominal size including approved damp proof admixture in proportion as recommended by the manufacture including curing etc. complete as directed.

REINFORCED CEMENT CONC WORK Providing and laying plain/reinforcement cement concrete works in prop 1:2:4( 1 cement : 2 coarse sand :4 coarse aggregate 20mm down ) including dewatering if necessary and curing compelete but excluding cost of from work and reainforcement for reainforced cement concrete work. (from work and reainforcement will and be measured and paid separately) (i) Using mixture machine (A) In sub-structure upto plint level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank not less than 100mm thick plinth level. (N) Without using admixture, plasticser c) M 20 or Prop. 1:5:3

(B) In super structure from plinth level up to 1st floor level. ii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, linte; sill band, beam, girder, bressumer, cantilever, staircase (except sprial staircase and landing) including preparing the top surface and finishing or nosing. (N) Without using admixture, plasticser c) M 20 or Prop. 1:1.5:3

SHUTTERING AND FORWORK TIMBER SHUTTERING (FORMWORK) Providing from work of 12mm thick plywood Board so as to give a rough finish including etc. height of proping and centering below supporting floor supporting floor to ceiling not exeeding 4.0M and removal of the same for situ reinforced concrete and plain concrete works in: Foundation, footings, base of columns, pile cap etc., (b) Using 25mm thick plank

Sides of tie beams, grade beams etc., (b) Using 25mm thick plank

PLYBOARD SHUTTERING (FORMWORK) Providing from work of 12mm thick plywood Board so as to give a rough finish including etc. height of proping and centering below supporting floor supporting floor to ceiling not exeeding 4.0M and removal of the same for situ reinforced concrete and plain concrete works in: Columns, pillars, Post & Struts of square/ rectangular/ polygonal in plan or any shape like Tee/ L etc. having plane vertical face.

Sides and Soffits of Beams, beam haunchings, cantilever griders, bressumers, lintels and horizental ties. A) For depth not exeeding 1.0M

MASONRY WORKS Providing brick soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to lavel and in pael after preparing the sub grade as directed including all labours and materilas and if necessary dewatering complete. a) Brick on flat soling

Brick work in cement mortar with 1st class brick including racking out joints and curing complete as directed. (I) In sub-structure upto plinth level including dewatering if necessary. (b) In proportion 1:6

1st class brick nogged wall in cement mortar in racking out joint and caring complete as directed in super structer above plinth upto 1st floor level. (a) 112mm thick brick wall (b) In cement mortar in proportion 1:4 (1 cement : 4 sand )

FLOORING AND FLOORING FINISHING CEMENT CONCRETE FLOORING 65 mm thick cement concrete floor consisting of 50 mm under layer of cement concrete in prop. 1:3:6 (1cement :3 coarse sand :6 coarse aggregate of 25mm and down) and 15mm thick waering layaer in cement concrete in prop. 1:1:2….. Includimh curing etc. complete as directed.

Providing polished ceramic wall tiles of approved quality, size shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 ( 1 cement: 3 coarse sand) including cutting… directed by the Department). (Walls means both inerior and exterior walls) a) Normal range ii) Of size 200mm×300mm and above

PLASTERING WORK 10mm thick cement plaster in single coat on rough side of brick/concrete walls for interior plastering up to 1st floor level including arises or rounded angles not execeeding 80mm girth and finished even and smooth including curing complete as directed. (b) In cement 1:4

15mm thick cement plaster in single coat on rough side of brick/concrete walls for interior plastering up to 1st floor level including arises or rounded angles not execeeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side. (c) In cement 1:4

Extra over item no. 6.2.1 to 6.2.3 for plastering on celling and soffits of stairs upto 1st floor level (instead of plastering on walls) including curing complete as directed.

FALSE CEILLING WORKS BISON PANEL CELING AND PARTION Providing, fitting and fixing in position false ceiling of 6mm thick Bison panel (cement bonded particle board) on timber frame of 1st class local wood (Hollock/ Bonsum/ Sundi) of 50mm × 50mm spaced at not more than 1.20m a part, fixed to the wall at the end with necessary nails, wood screws, hooks, botls etc.. as directed by the Department for all levels. (a) Both sides commercial

Providing Pre Painted Galvanized Iron Sheet Roofing (PPGI) at all levels including fitting and fixing with self driling, self tapping screws complete. (Roof trusses, purlins etc. to be measured and paid serparately) Dyna roof/ Wonder Roof/ JSW Steel/ Specturm or equivment as directed by the Department. (iii) 0.50 mm thick

Providing Pre Painted Galvanized Iron Sheet Roofing (PPGI) accessories (Ridges/ Valley/ Gutter/ Flashing) at all levels including fitting and fixing with self driling, self tapping screws complete. Dyna roof/ Wonder Roof/ JSW Steel/ Specturm or equivment as directed by the Department. (iii) 0.50 mm thick

WOOD WORKS Providing wood work in frame of false ceiling partitions etc. sawn, wrought, framed hoisted and fixed in position with spikes, nails, M.S flat, angle/cleats with bolt and nuts complete including kircide oiling two coats to unexposed surfaces of the timber (M.S flat, angle cleats, and bolt and nuts required for flat, angle cleats wherever necessary shall be measured and paid separately) b) With Gamari/Bonsum/Sundi

DOOR SHUTTER Providing, fitting and fixing factory made Santro Flush door shutters having core & cross bands fabricated from seasoned 1st class timber, 25mm core battens, 2.5mm to 3.5mm unifformly thick cross bands, style & rails made from hardwood tiber of width not less than 50mm, fixed to the door frames (chowkath) with necessary hinges, screws, bolts etc. as specified and directed at all levels ( Door fixtures and fittings will be measured and paid separately) (b) 35 mm thick

MS GRILLWORK Providing, fitting and fixing M.S. Grill of requred pattern for windows/ clerestory windows/ opening with M.S. flats at requred spacing in frame all round, square or round M.S. Bars with round headed bolts and nuts or screws. I. Plain grill (b) Fixed to Brickwork/P.C.C/R.C.C

Providing, fitting and fixing anodised aluminium windows and ventilators of standard sections of approved brand (HINDALCO/NALCO/BALCO/JINDAL/BHAG WATI SAI (with proof of puschase of ingot from primary producer) / Other equivment primary producer) without horizental glazing bars joints mitred and horizental glazing bars joints mitred and welded (manufactured to relevant IS specifications).. and providing and fixing handles, frictions strays, joining cleat, bolting device, locking arrangement, spring catch as requred complete as specified and directed for all levels. (a) Side hung and Top hung windows and ventilators (ii) 5mm frosted glass

PAINTING WORKS DISTEMPER m) Distempering two coas with oil bound distemper of approved brand and manufacture and of required shade on new wall surface to give and even shade over and including a priming coat with ditemper primer of approved brand and manufacture after throughly brooming the surface free from throughly brooming the suface free from mortar droppings and other foreign matter and including preparing surfaces even and sand pepered smooth. (i) Painting coat with distemper primer

(ii) Top coat

Providing two coats of J.K Wall Putty (White Cement based for concrete/mortar walls and ceilling both internal and external) after removing all lossely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm)

Finishing old/new wall surface after cleaning and cleaning the surface etc. including scaffolding complete as directed at all levels (two coats)

PAINTING ON WOOD BASED SURFACES Applying priming coat over new wood and wood; based surfaces over 100mm in girth / width after and including preparing the surface by througly cleaning oil, grease, dirt and other foriegn matter, sand papering and knotting a) With ready mixed paint, wood primer (pink)

Painting two coats (excluding priming cat) on new wood and wood based surfaces with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ICICI paint/ J & N Pint/Nerolac) to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matter sand papering and stopping. a) Surface over 100mm in width or girth i) General purpose (Asian paint/ Berger paint/ ICICI paint/ J & N Paint/Nerolac)

PAINTING ON STEEL AND OTHER METAL SURFACES Applying primary coat over new steel and other metal suface over 100mm in with or girth after preparing the surface by throughly claening oil, grease,dirt and other foreign mater and scoured with wire brushes, fine steels, wood scapers and sand paper. a) With ready mixed "red-lead/red-oxide" primer.

Painting two coats (excluding priming cat) on new wood and wood based surfaces with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ICICI paint/ J & N Pint/Nerolac) to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matter sand papering and stopping. a) Surface over 100mm in width or girth i) General purpose (Asian paint/ Berger paint/ ICICI paint/ J & N Paint/Nerolac)

DOOR AND WINDOWS FITTINGS ALUMINIUM FITTINGS Supplyings, fitting, fixing anodised aluminium fittings of approved make, resonably smooths, free from sharp edges and cornes, flaws and other defects and with counter sunk hloes for screws including necessary aluminium screws etc. complete.(anodised to bright natural matt & satin finished) a) Slinding door bolts ii) 250mm × 16mm

DOOR AND WINDOWS FITTINGS ALUMINIUM FITTINGS Supplyings, fitting, fixing anodised aluminium fittings of approved make, resonably smooths, free from sharp edges and cornes, flaws and other defects and with counter sunk hloes for screws including necessary aluminium screws etc. complete.(anodised to bright natural matt & satin finished) b) Tower bolts ii) 200mm × 12mm

DOOR AND WINDOWS FITTINGS ALUMINIUM FITTINGS Supplyings, fitting, fixing anodised aluminium fittings of approved make, resonably smooths, free from sharp edges and cornes, flaws and other defects and with counter sunk hloes for screws including necessary aluminium screws etc. complete.(anodised to bright natural matt & satin finished) c) Door handles ii) 150mm

STEEL AND IRON WORKS REINFORCEMENT Supplying, fitting and fixing in position reainforcement bars conforming to relavent I.S. Code for R.C.C work/R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs spacers etc. complete. (No Extra measurement for lap, hook, chair , anchor etc. will be entertained in the measurement as the are including in the rates) (Upto 1st floor level) B) Other ISI approved TMT reinfocement bar (SAI/BISCON/THERMAX

Providing, fitting , hoisting and fixing of roof trusses fabrication out of combination of any two or all of the folowing sections (i) Squre section (ii) Rectangular Hollow section of specification RSH/SHS nad (iii) M.S. circular hlollow section of Grade 210.....M.S. cleats, base plates, bolts and nuts etc. as directed as per specifications b) Using other ISI marked approved circular hollow section

Providing, fitting and fixing powder coated pressed steel door frame made of 1.25mm/1.6mm thick sheet of various sizes with necessary hinge jamb, lock jamb, head and steel base ties at the bottom of the frame etc....complete as directed by the department for all levels. (P.C.C. to be measured and paid for separately). (a) 1.25mm thcik sheet (iii) Size 125mm × 60mm (Single rebate)

PLINTH PROTECTION WORKS AND DRAINS Providing plinth protection with bricks flat laid in cement mortar 1:4 and finishing with 15mm thick cement plaster in prop. 1:2 with a floating coat of neat cement finish.

Providing drain with brick work in cement mortar in prop. 1:5 with half brick thick side walls and 100 mm thick CC (1:3:6) base over one brick flat soling including 15mm thick cement plastering in prop. 1:3 finishing with a floating coat of cement slurry as directed with necessary shuttering for sides and earth work in excavation of foundation trances and refilling the sidesn after completion of work etc. as specified. ii) 300mm wide and average 150mm deep with bed slope in 150 with intial depth of 100mm.

ANTI TERMITE TREATMENT Pre contruction anti-termite treatment at the bottom of foundation pits and walls on either side up to a height of 300mm from bottom of the excavation made for column plinth beam, wall, trenches etc. by applying the emulsion @ 5 (five) litres per square meter of the surfaces area before starting construction work (supplying of necessary tools and accessories by the contractor) as per the direction of the department complete. a) With aqueous emulsion having concentration 1:19 with chloropirophose solution and water.

Cost of Septic Tank, 50 user capacity.

DETAILS ESTIMATE OS SANITARY & PLUMBING WORKS INDIAN TYPE OF CLOSET Providing fitting and fixing vitreous china pedestel tyoe water closet squatting pan (Indian type W.C. Orissa pattern) with all fittings and fixing complete including cutting and making good to the walls and floors whereever required. (Flushing Cistern to be paid separately) Indian type W.C Orissa pattern of size 580mm × 440 mm a) White i) Parryware make

Providing fitting and fixing vitreous china pedestel tyoe water closet (European type W.C. pan 400mm high) with seat and lead, CP brass hinges and rubber buffers, CI/MS brackets, 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately) A) Parryware make/a) White/(vii) Niagara (Cat No.C0252) (inclusive of seat cover)

PVC FLUSHING CISTERN Supplying, fitting and fixing PVC flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. complete as directed and specified (pipes will be measured separately) i) Parryware make/a) White/(i) Economy Single Flush (Cat No.8090/C8055)

URINAL Providing fitting and fixing vitreous china flat back type lipped front urinal basin of with automatic flushing cistren with standard flush pipe and CP brass... and making good the walls & floors wherever required. A) Parryware a) White (i) Integrated EFS-Smart DC...

DIVISION PLATE Supplying, fitting and fixing vitreous china division plate including fitting and fixing compare as directed and specified. A) Parryware a) White (i) Partion Magnum / Large (Cat. No.C0571/07)

WASH BASIN Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug, PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop coacks, waste coupling are to be separately) Basin (without pedestal) A) Parryware (A)White (iii) Tunga Basin 450 × 300 l (Cat No.C0401)

FITTINGS & ACESSORIES MIRROR Providing, fitting and fixing Mirror with plastic frame of size 500×400mm complete as directed and specified

SOAP TRAY, SOAP DISH, LIQUID SOAP DISPENSER AND LIQUID SOAP CONTAINER Providing, fitting and fixing recessed soap tray / soap dish complete as directed and specified Providing, fitting and fixing recessed soap tray / soap dish complete as directed and specified (i) Parrywake Make (ii) Wall Soap tray(Cat.No.C0401)

TOWEL RAIL, TOWEL RACK & TOWEL RING Providing, fitting and fixing CP towel rail complete as directed and specified (a) Jaquar make (ii) Queen's (450mm long) (Cat. No.AQN- 7711A)

BOTTLE TRAP Providing, fitting and fixing CP bottle trap complete as directed and specified (a) Jaquar make/ (ii) Bottle trap (with internal partiion) 32mm size with 300mm long wall connection pipe (Cat.No.ALD-769B)

BIG COCK Providing, fitting and fixing CP bib cock 15mm dia of appropved brand directed and specified (a) Jaquar make/ (a) Continental/Clarion (i) Standard\

PILLAR COCK Providing, fitting and fixing CP bib cock 15mm dia of appropved brand directed (a) Jaquar make/ (a) Continental

PIPES & FITTINGS PVC PIPES, BENDS, JUNCTIONS, TEES ETC. Supply, fitting and fixing PVC pipes of 6 kg/cm2 (Suprem/Princes) or other ISI approved including joining, ftting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches (ii) 110mm dia.

(iv) 75mm dia

b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.

(iv) 75mm dia

Supply, fitting and fixing 87.5 degree PVC bend of (Suprem/Princes) or other ISI approved including joining, ftting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.

Supply, fitting and fixing 45 degree PVC bend of (Suprem/Princes) or other ISI approved including joining, ftting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.

Supplyment fitting and fixing PVC Plain single tee with door of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplyment fitting and fixing PVC single 'Y' of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.

Supplyment fitting and fixing PVC reducing Tee of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm× 110mm

CPC PIPES Providing and fixing Chlorinated Polyvinyle Chloride (CPVC) Pipes, having thermel stability for hot and cold water supply including all CPVC plain and brass threaded fittings i/c fixing the clamps at 1.00m spacing. This includes joint of pipe. (A) Exposed or in trenches (Vertical in shaft & Terrace) C) 25 mm nomial outer dia pipe.

CPC PIPES Providing and fixing Chlorinated Polyvinyle Chloride (CPVC) Pipes, having thermel stability for hot and cold water supply including all CPVC plain and brass threaded fittings i/c fixing the clamps at 1.00m spacing. This includes joint of pipe. (A) Exposed or in trenches (Vertical in shaft & Terrace) E) 40 mm nomial outer dia pipe.

(B) Concealed pipe with cutting chases & making good the walls a) 15 mm nomial outer dia pipe.

(B) Concealed pipe with cutting chases & making good the walls b) 20 mm nomial outer dia pipe.

(B) Concealed pipe with cutting chases & making good the walls c) 25 mm nomial outer dia pipe.

GRATING Peoviding fitting & fixing C.I. Grating to the floors complete as directed and specified. (a) 110mm dia

VALVE Supplying and fitting ball valve as specified and directed. a) 25 m dia (gun material)

Supplying fitting and fixing gun metal check valve including necessary threads to pipes. B) 40 mm dia (Heavy type)

SOAK AND INSPECTION CHAMBER Construction of inspection pit inside measurement 450mm×450mm ×450mm flush wirth 100mm diameter HCI/PVC pipes and cement concrete base in proportion 1:3:6 over flat brick soling, 12cm brcik wall in cement mortar in prop. 1:4 ... excavation of pit as directed.

DETAILS ESTIMATE OF ELECTRICAL WORKS Wiring for light/fan/call bell point with 2×1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR confirming to IS-694: 1990 with flexible bright annealed electrolyic copper conductor for volatage grade up to 1100 volts (Finolex/RR Kabel/ Nicco/ Anchor or Equivement Make as approved by the Deppt.) in surface / recessed conduit wiring system with 20mm dia rigid ISI marked Steel conduit pipe complete. 1.Short point up to 3.00 metre. length.

Wiring for light/fan/call bell point with 2×1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR confirming to IS-694: 1990 with flexible bright annealed electrolyic copper conductor for volatage grade up to 1100 volts (Finolex/RR Kabel/ Nicco/ Anchor or Equivement Make as approved by the Deppt.) in surface / recessed conduit wiring system with 20mm dia rigid ISI marked Steel conduit pipe complete. 2.Medium point up to 6.00 metre. Length.

Wiring for light/fan/call bell point with 2×1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR confirming to IS-694: 1990 with flexible bright annealed electrolyic copper conductor for volatage grade up to 1100 volts (Finolex/RR Kabel/ Nicco/ Anchor or Equivement Make as approved by the Deppt.) in surface / recessed conduit wiring system with 20mm dia rigid ISI marked Steel conduit pipe complete. 3.Long point up to 10.00 metre. Length.

Wiring to 5 a pin 6 Amps plug point with 1.5 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR confirming to IS-694: 1990 with flexible bright annealed electrolyic copper conductor for volatage grade up to 1100 volts (Finolex/RR Kabel/ Nicco/ Anchor or Equivement Make as approved by the Deppt.) in surface / recessed ISI marked Steel 20 mm. dia. conduit pipe wiring system including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete. 1.Short point up to 3.00 metre. length.

Wiring to 5 a pin 6 Amps plug point with 1.5 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR confirming to IS-694: 1990 with flexible bright annealed electrolyic copper conductor for volatage grade up to 1100 volts (Finolex/RR Kabel/ Nicco/ Anchor or Equivement Make as approved by the Deppt.) in surface / recessed ISI marked Steel 20 mm. dia. conduit pipe wiring system including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete. 2.Medium point up to 6.00 metre. Length.

Wiring to 5 a pin 6 Amps plug point with 1.5 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR confirming to IS-694: 1990 with flexible bright annealed electrolyic copper conductor for volatage grade up to 1100 volts (Finolex/RR Kabel/ Nicco/ Anchor or Equivement Make as approved by the Deppt.) in surface / recessed ISI marked Steel 20 mm. dia. conduit pipe wiring system including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete. 3.Long point up to 10.00 metre. Length.

Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR confirming to IS-694: 1990 with flexible bright annealed electrolyic copper conductor for volatage grade up to 1100 volts (Finolex/RR Kabel/ Nicco/ Anchor or Equivement Make as approved by the Deppt.) in surface / recessed ISI marked Steel 20 mm. dia. conduit pipe wiring system including earth continuity with 2.5 sq. mm. cable to the 3rd pin of the socket as required complete with 20mm. dia. Steel conduit (AKG or equivment as approved by the Deptt.) 1.Short point up to 3.00 metre. leng

Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR confirming to IS-694: 1990 with flexible bright annealed electrolyic copper conductor for volatage grade up to 1100 volts (Finolex/RR Kabel/ Nicco/ Anchor or Equivement Make as approved by the Deppt.) in surface / recessed ISI marked Steel 20 mm. dia. conduit pipe wiring system including earth continuity with 2.5 sq. mm. cable to the 3rd pin of the socket as required complete with 20mm. dia. Steel conduit (AKG or equivment as approved by the Deptt.) 2.Medium point up to 6.00 metre. Length.

Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR confirming to IS-694: 1990 with flexible bright annealed electrolyic copper conductor for volatage grade up to 1100 volts (Finolex/RR Kabel/ Nicco/ Anchor or Equivement Make as approved by the Deppt.) in surface / recessed ISI marked Steel 20 mm. dia. conduit pipe wiring system including earth continuity with 2.5 sq. mm. cable to the 3rd pin of the socket as required complete with 20mm. dia. Steel conduit (AKG or equivment as approved by the Deptt.) 3.Long point up to 10.00 metre. Length.

Wiring for circuit wiring with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR confirming to IS-694: 1990 with flexible bright annealed electrolyic copper conductor for volatage grade up to 1100 volts (Finolex/RR Kabel/ Nicco/ Anchor or Equivement Make as approved by the Deppt.) in surface / recessed PVC conduit (Belia/ AKG/ Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Dept.) wiring system. With 2 × 1.5 sq. mm cable in 20 mm dia. 2mm thick/ haevy rigid PVC IS: 9537 Part - III conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR confirming to IS-694: 1990 with flexible bright annealed electrolyic copper conductor for volatage grade up to 1100 volts (Finolex/RR Kabel/ Nicco/ Anchor or Equivement Make as approved by the Deppt.) PVC conduit (Berlia/ AKG/ Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Dept.) including earth continuity in suface/ recessed 20 mm. dia. 2mm thick/ haevy ISI marked IS: 9537 PART-III rigid PVC conduit wiring system. 1.With 2 × 2.5 sq. mm + earth continuity with 1×1.5 sq. mm in 20 mm dia. 2mm thick/ haevy rigid PVC IS: 9537 Part - III conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR confirming to IS-694: 1990 with flexible bright annealed electrolyic copper conductor for volatage grade up to 1100 volts (Finolex/RR Kabel/ Nicco/ Anchor or Equivement Make as approved by the Deppt.) PVC conduit (Berlia/ AKG/ Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Dept.) including earth continuity in suface/ recessed 20 mm. dia. 2mm thick/ haevy ISI marked IS: 9537 PART-III rigid PVC conduit wiring system. 3.With 2 × 6 sq. mm + earth continuity with 1×4 sq. mm in 25 mm dia. 2mm thick/ haevy rigid PVC IS: 9537 Part - III conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR confirming to IS-694: 1990 with flexible bright annealed electrolyic copper conductor for volatage grade up to 1100 volts (Finolex/RR Kabel/ Nicco/ Anchor or Equivement Make as approved by the Deppt.) in suface/ recessed 20 mm. dia. 2mm thick/ haevy ISI marked IS: 9537 PART-III rigid PVC conduit PVC conduit (Berlia/ AKG/ Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Dept.)wiring system. 5.With 4 × 16 sq. mm + earth continuity with 2×10 sq. mm in 40 mm dia. 2mm thick/ haevy rigid PVC IS: 9537 Part - III conduit.

Supplying with fitting and fixing sheet steel, phosphatised, power painted dust & vermin proof revsible Double door IP-43 double door surface mounting horizental TPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. Richa, Bentec, Adhunic, V-Gaurd make) 1.4 way TPN (8+12) double door

Supplying with fitting and fixing sheet steel, phosphatised, power painted dust & vermin proof revsible Double door IP-43 double door surface mounting horizental TPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. Richa, Bentec, Adhunic, V-Gaurd make) 2.6 way TPN (8+24) double door

Supplying with fitting and fixing sheet steel, phosphatised, power painted dust & vermin proof revsible Double door IP-43 double door surface mounting horizental TPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. Richa, Bentec, Adhunic, V-Gaurd make) 1.4 way SPN double door

Supplying with fitting and fixing sheet steel, phosphatised, power painted dust & vermin proof revsible Double door IP-43 double door surface mounting horizental TPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. Richa, Bentec, Adhunic, V-Gaurd make) 2.6 way SPN double door

Supplying with fitting and fixing sheet steel, phosphatised, power painted dust & vermin proof revsible Double door IP-43 double door surface mounting horizental TPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. ABB, Schneder MG, legrand, Hager make) 4 way TPN ( 8+12) double door

Supplying with fitting and fixing sinlgle Pole 10 KA 240/415V 50 Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deppt. B Series (Schneider MG, legrand, Hager make) 1.6 to 32A

C Series (Schneider MG, legrand, Hager make) 6 to 32A

Supplying with fitting and fixing TP 10 KA 240/415V 50 Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deppt. C Series (ABB,Schneider MG, legrand, Hager make) 6 to 32A

Supplying with fitting and fixing TPN 10 KA 240/415V 50 Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deppt. C Series (ABB,Schneider MG, legrand, Hager make) 63A

Supplying with fitting and fixing 30/100/300mA Sensitivity 240/415V 50 Hz 4P RCBO of the following capacity complete with making necessary connection as approved, specified and directed by the deppt. 30mA sensitivity 4P RCBO (ABB,Schneider MG, legrand, Hager make)

Supplying with fitting and fixing 30/100/300mA Sensitivity 240/415V 50 Hz 4P RCBO of the following capacity complete with making necessary connection as approved, specified and directed by the deppt. 30mA sensitivity 4P RCBO (ABB,Schneider MG, legrand, Hager make) 20A

Supplying with fitting and fixing 30/100/300mA Sensitivity 240/415V 50 Hz 4P RCBO of the following capacity complete with making necessary connection as approved, specified and directed by the deppt. 30mA sensitivity 4P RCBO (ABB,Schneider MG, legrand, Hager make) 40A

Supply, installation 7 testing of Copper Plate earth station with 600 mmx×600 mm× 3 mm copper earth plate with necessary 40 mm dia G.I. medium duty watering pipe with G.I. Fittings such as Socket, Tee, elbow, nipple and 50mn×40mm G.I. reducing socket for funnel including locking arrangement with 300 mm ×300 mm×+6mm C.I. hinged coveer plate complete with digging of both inner & outer surface of wall as specified and directed by the deppt.

Supplying with fitting and fixing 20 mm ×5 mm G.I. strips drawn on vertically or horizontally on building wall/parapet wall in surface system complete with supply of G.I. Nuts & Bolts, Screws etc including riveting, soldering and making connection as approved by the Deppt.) with earth electrode G.I. stripts and Lightining Arrestor etc. as specified and direction by the deppt.

Supplying with fitting and fixing 20 mm ×3 mm Copper strips drawn on vertically or horizontally on building wall/parapet wall in surface system complete with supply of G.I. Nuts & Bolts, Screws etc including riveting, soldering and making connection as approved by the Deppt.) with earth electrode G.I. stripts and Lightining Arrestor etc. as specified and direction by the deppt.

Supplying & lying of 6 SWG G.I. earth from Earth Electrode (below G.L.) to electrical switch gears or electrical machineries including making necessary connection as approved, specified and directed by the deptt.

MODULAR SWITCH Supplying with fitting fixing of 6/10 amp one way modular clip in switch with LED, MODEL RANGE LEGRAND (ARTEOAR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying including installation of socket outlet 10 Amps 3 pin combine shuttered complete, MODEL RANGE LEGRAND (ARTEOAR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying with fitting fixing of 16 amp one way modular clip in switch with LED, MODEL RANGE LEGRAND (ARTEOAR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying including installation of socket outlet 10/16 Amps 3/5 pin combine shuttered complete, MODEL RANGE LEGRAND (ARTEOAR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying with fitting fixing of electronic modular fan speed controller 2 - module type MODEL RANGE LEGRAND (ARTEOAR), ANCHOR (VIOLA), MK (WRAPAROUND/PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including 100 watt electronic modular 4 step speed control 2 - module type

Supplying with fitting fixing of following Metal boxes for MODEL RANGE LEGRAND (ARTEOAR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) in surface/ recessed system complete as per direction of department. 1. 1-2 module type Metal.

Supplying with fitting fixing of following Metal boxes for MODEL RANGE LEGRAND (ARTEOAR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) in surface/ recessed system complete as per direction of department. 2. 3 module type Metal.

Supplying with fitting fixing of following Metal boxes for MODEL RANGE LEGRAND (ARTEOAR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) in surface/ recessed system complete as per direction of department. 3. 4 module type Metal.

Supplying with fitting fixing of following MODEL RANGE LEGRAND (ARTEOAR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) front plate of suitable colour as per direction of department. 1. 1 module.

Supplying with fitting fixing of following MODEL RANGE LEGRAND (ARTEOAR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) front plate of suitable colour as per direction of department. 2. 2 module.

Supplying with fitting fixing of following MODEL RANGE LEGRAND (ARTEOAR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) front plate of suitable colour as per direction of department. 3. 3 module.

Supplying with fitting fixing of blank plate sinlge in modular switch system, MODEL RANGE LEGRAND (ARTEOAR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying including fitting fixing of following A.C. Exhaust fan in the exixting hole on the wall of following sweeps with making necessary connection as approved by the Deptt.) as required complete and as directed by the Department. Ventilator DX 250 mm sweep Louver type (ORIENT make), Brick Air 250 mm sweep Louver type/ Trans Air 150 mm sweep (Croption make), Ventile Air DX 150 mm sweep Louver type (Havells make)

Supplying including fitting fixing of following star rated A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.s etc. as required complete and as directed by the Department. (ORIENT PSPO make / Usha make/ CROMPTON make/ Havells/ ATC/ V GAURD make) Enegy efficient 5- star 1200 mm sweep. ORIENT PSPO / Usha / CROMPTION / Havells/ ATC or equivalent make.

Supplying, installation, testing and Commission of following luminaries complete with all accessories such as ballast, starter etc. mounting with necessary support with 1.5 sq.mm P.V.C. insulated S.C.copper conductor as required and as directed by the consultant. Philips TLED Battern BN 108C LED 20S PSU NW WH

Supplying, installation, testing and Commission of following luminaries complete with all accessories such as ballast, starter etc. mounting with necessary support with 1.5 sq.mm P.V.C. insulated S.C.copper conductor as required and as directed by the consultant. Model No DN395B LED 20S-4000 PSR WH

Supplying and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2×10 sq mm. 3×10 sq mm, 4×6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908 (Part 1) 1988 armoured U.G. cable U.C. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand coushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/Havells/RPG/CCI/Polycab/Gloster /Finolex make) 3 & 12 Core A2XFY 300.00 Sq. mm.3 & 1/2 Core armoured U.G. cable.

chakrasing Muchahary