Rehabilitation of Hydro-Mechanical Parts and Electrical Works of Matiyari Medium Irrigation Project in Mandla under DRIP-II

Design, Drawing, fabrication, supply, erection, testing and commissioning of Vertical lift fix wheel type sliding gate/inter changeable Stop log gates consisting of skin plate, stiffeners, horizontal girders, pulley, pulley supports, bracings, lifting lug, bracket, rubber seals, clamps plates etc., with all accessories as per relevant for Canal , sluice Vertical gates and spillway gates including cost of all materials, machinery, labour, cutting, bending, aligning, anchoring, welding, seal fixing, tools and tackles etc., finishing, cleaning, applying two coat of zinc rich epoxy primer to give dry film thickness of 70± 5 microns and finish coat(two coats)of solvent less coal tar epoxy paint using airless spray to provide dry film thickness of 150± 5 microns per coat thus total dry film thickness of all coats, including primer coating, should not be less than 350 microns., complete as per specifications and approved drawings complete, including packing & forwarding, transportation charges for structural steel components and other materials.

Design, Drawing, fabrication, supply, erection, testing and commissioning of Adequate capacity Electrically operated screw type hoist according to relevant IS code, consisting of supporting structure, platform bridge etc., operating handle ,gate position indicator, plumber block, couplings, motor, reduction gear unit, limit switch, control panel, cables, with inbuilt manually operation with all required accessories for operating Head/cross/ escape regulator gate including cost of all materials, machinery, labour, tools and tackeles, cutting, aligning, anchoring, welding, finishing, cleaning, greasing, oiling, applying two coats of zinc chromate red oxide primer and three coats of approved synthetic enamel paint etc., complete as per specifications and approved drawings with all lead and lifts, including packing & forwarding, transportation charges for all materials

Painting of Spillway gates, sluice gates, canal gates (both vertical or radial), stop log gates, exposed embedded parts and all un machined ferrous surface ( hoist cylinders, cylinder heads, hydraulic piping, pipe fittings , bonnet covers),exposed to water as per IS 14177, for which surface preparation by blast cleaning of class “B” primer coat (one coat) of inorganic zinc silicate (preferably airless spray) or alternatively, two coats of zinc rich primer (containing not less than 85% zinc on dry film) to give dry film thickness of 70 ± 5 micron and finish coat (two coats) of solvent less coal tar epoxy paint using airless spray to provide dry film thickness of 150± 5 micron per coats. Thus, total dry film thickness of all the coats, including primer coating, should not be less than 350 microns; this will include expenses on mobilization and demobilization of equipments. For maintenance painting the surface preparation shall be done by appropriate hand And power tool cleaning, prior to hand power tool cleaning. Any heavy layer of rust should be removed by chipping visible oil, grease, dirt and other foreign material be cleaned using solvents like clean mineral spirits, xylot or white gasoline. After hand and power tool cleaning the surface should be cleaned of loose dust and debris and /or blast cleaned as laid down in para 7.0 of IS code 14177.After the surface preparation the primer and finishing coats shall be carried out as provided above for painting etc. complete Upto 1.5M Height

Beyond 1.5M Height

Painting of machinery, including gearing, housing, shafting, bearing, pedestals, oil tanks, control cabinets, hoist beams, pipe support, clamps, ladders etc., of hoists and supporting structures, as upto 1.5 m height

Beyond 1.5M Height

cleaning gates /hoist /embedded parts for repainting by removing rust oil, paint grease etc . By using wire brush , scrubber , rust remover and applying a coat of rust remover and applying a coat of rust inhibitive compound etc. complete

Supplying and fixing bulb type Teflon cladded rubber seals and stainless steel counter sunk bolts/ nuts/ washers of approved quality

Supplying and fixing flat rubber seals and stainless steel counter sunk bolts/ nuts/ washers of approved quality including cost of all materials, labour, removing existing worn-out/ damaged flat type rubber seals, from gates, cleaning surface, making holes in new seals, fixing new seals/ bolts/ nuts/ washers tightly in position, scaffolding etc. Complete. R/C gate size 12×5m

Supply ,installation of PV Module 75 Wp Under STC ,MNRE Approved 012 Battery, Minimum 360 Wh LiFePo4 Battery, BIS Certified, 30AH/12.8 Volt013 12 Watt, W-LED luminary, Light(White LED based Light) 01 , Erection of System with 5 Year warranty as per MMRE technical specification.