SPL REPAIR TO BLDG NO. MA 112 CONVERSION OF LT OVERHEAD INTO UNDERGROUND CABLE SYSTEM AND PROVN OF CERETAIN LBW AND REVENUE WORKS AT BAGRAKOTE MIL STN UNDER GE SEVOKE ROAD

Amount

Taking down chowkats with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sqm each complete all as specified.

Taking down chowkats with shutters (without taking off shutters from the frames) area exceeding 1.50 Sqm but not exceeding 4.00 Sqm each complete all as specified.

Dismantling wrought iron or mild steel work of any description not other wise provided for complete all as specified.

Dismantling plain or corrugated steel sheeting any gauge or thickness as in roof covering complete all as specified.

Dismantling timber scantling's 40 Sqcm and over in section in any position as in framed works complete all as specified.

Demolition of bricks work built in cement mortar inlcuding all quoins, arches, pillar, etc complete all as specified.

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc 15 cm thickness (below or above GL) complete all as specified.

Dismantling wall & ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified.

Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water etc complete all as specified.

M&L for Brick work with sub class 'B' bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified.

M&L for Brickwork with sub-class `B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified.

M&L for PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in block for hold fast, filling in frames, copings or similar work and finished the surface with existing including form work complete all as specified.

S&F Mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlines to steel trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified.

S&F pressed steel frames (Size-165X60mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified .

S&F factory made 2nd class hard wood rail and style, 35mm thick, plain framed, panelled shutter (two panel ) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (part I), kiln seasoned and chemically pressure treated complete all as specified.

S&F 35 mm thick Glazed and skeleton shutters open rebated and prepare to receive glass, gauze etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing gauge etc size of members of shutters as specified in SSR part-I Section 8 and clause 8.24(a) of second class hard wood all as directed.

S&F mild steel tower bolts stove enamelled black, with bright bolt 200 mm long complete all as specified.

S&F 300 mm long mild steel sliding door bolts, plate type stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts four on bolts plate & two on staple plate complete all as specified.

S&F mild steel pressed handles oval type, stove enamelled black 150 mm long. complete all as specified.

S&F 150mm Mild steel ordinary rat tail rod pattern springs including roller and roller plate complete.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F 150mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified.

S&F 100mm Long Stainless Steel Butt Hinges, fixed to PVC door frame and shutter, complete all as specified and as directed

S&F 150mm long Extruded aluminium alloy handles, fabricated type., anodised complete all as specified.

S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay complete with glazing bars, dovetailed or welded including painting with one shop coat for zinc chromate primer complete all as specified and directed.

All as per item No.26 above, but without glazing bars.

S&F Steel ventilators with top hung shutter including hinges,steel peg stay, complete all as specified and directed.

S&F 3mm thick glass sheet ordinary quality & glazing with oil putty in square not exc 0.50 Sqm in each pane complete all as specified & directed.

S&F galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanized wire staples complete all as specified.

S&F framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde-E-165 complete all as specified.

M&L rendering 15mm thick in CM 1: 6 on fair faces of brick/concrete surfaces finished even & smooth without using extra cement complete all as specified.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 including mixing WPC as per manufacturers instruction, finished even and smooth without using extra cement. (WPC shall be measured seperately)

Supply only integral water proofing compound complete all as specified.

S&F mild steel Roof trusses (framed), trussed, purlins, crane, gantries, rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc( Fe 410-W Gde-E-250 quility-B Including preparation of surface and one shop coat of zinc chromate primer paint at contractors workshop before fabrication complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering fixed with self drilling and self tapping screws, neoprene and limpet washers complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering fixed with self drilling and self tapping screws, neoprene and limpet washers complete all as specified and directed.

S&F mild steel screw bolts, 5 to 10mm dia (machine made) with hexagonal head one end and screwed the other, or screwed both end each screwed end to be fitted with washers and one hexagonal or square nut exceeding 05cm and not exceeding 10cm long complete all as specified and directed.

S&F 605X605mm anodised aluminium snap grid frame work for false ceiling including 2.5mm dia mild steel wire galvanized class 3,@ 60cm centre to centre and fixed to steel or wooden member all as specified and as directed.

M&L 4mm thick non asbestos fibre cement building boards fixed or laid/inserted to aluminium frame work in ceiling complete all as specified and directed.

Preparing of new non AC board surfaces/ new plastered surface and applying three coat of white wash compelet all as specified and directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified.

M&L for rendering in CM (1:4), 10mm thick on fair faces of brick work or concrete surfaces for fixing of wall tiles complete all as specified.

M&L for screed bed or bedding layer of cement mortar 1:6, 15mm thick for laying floor finishes complete all as specified.

M&L for glazed ceramic coloured tiles in vertical surface 300x200x7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces complete all as specified.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces complete all as specified.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in Skirtings etc. set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces complete all as specified.

M&L for 25 mm thick Plain Cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in floor complete all as specified.

M&L 75mm thick cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in plinth protection & paving finished even & smooth without using extra cement complete all as specified.

M&L for preparation of new untreated wood and wood base material of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L for preparation of new steel surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified.

M&L for preparing new steel and iron surfaces of any description n.exc 10 cm in width or girth and apply two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified.

M&L RCC 1:2:4 , type B1,(using 20mm graded stone aggregate) as in lintels upto 1.5m clear span and lintel band, roof band and other similar items including form work all as specified.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed, not less than 0.9mm dia or securing with clips complete all as specified.

All as per item No.54 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders all as specified and directed.

S&F mild steel work (miscellaneous) as in wind ties for roof, flat iron fillets (for securing wire mesh etc) including drilling holes for securing bolts and fixed with bolts and nuts etc and similar work conforming to Fe-290.Gde-E-165, complete all as specified and as directed.

Complete removal of existing treatment on wall surfaces and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and as directed

Preparation of new plaster surfaces and applying two coats of distemper oil emulsion over a coat of chalk whiting on wall complete all as specified.

Preparation of old treated surfaces and applying one coat of distemper oil emulsion on wall complete all as specified.

Preparation of new or previously untreated wall surfaces and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and as directed

Taking down 15 mm bore GI pipe line and connections including fittings and removal to store or cleaning for reuse, complete all as specified and as directed

Taking down 20 mm bore GI pipe line and connections including fittings and removal to store or cleaning for reuse, complete all as specified and as directed

S&F 15mm bore stop valves fancy type cast copper alloy, chromium plated, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for union and fixed including taking down of old unserviceable complete all as specified.

All as per item No. 63.00 above but fancy type, chromium plated with long shank and cup (conncelaed type) 15mm bore complete all as specified.

S&F PVC connection 15mm dia with PTMT nuts of length 450mm complete all as specified.

S&F in repairs (EWC) Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including all fittings complete and fixing to flush pipe and outlet pipe complete all as specified and as directed

S&F in repairs Vitreous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including fittings complete all as specified.

S&F PVC valveless, syphonic action type flushing cistern low level, 10 litre capacity with it's complete accessories, including connection to water pipe and PVC 32 mm dia flush pipe etc.complete all as specified.

S&F vitreous china wash hand basin, white, flat back, size 550x400 mm including brackets fixed in repair complete all as specified and as directed.

S&F brass chromium plated Tubular towel rail, 20mm dia, D type, 60 cm long between flanges complete all as specified.

S&F pillar taps, 15mm bore fancy type, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe complete all as specified.

Supply only 32 mm waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement & other end fixed complete all as specified.

S&F low density 32mm dia bore polythene waste pipe (LDPE) of pressure rating 0.6 Kgf/Cm2 complete all as specified.

S&F in repairs 15 mm bore two way bib cock with wall flange chromium plated with crutch or butterfly handle screwed down screwed for iron pipe 15 mm bore and fixed complete all as specified and as directed.

S&F in repairs 15mm bore CP Toilet Hand Pressed Nozzle (Heath faucet) with 1.5 meter long tube with CP wall bracket complete all as specified and as directed.

S&F 15mm bore steel water tubes medium grade galvanised with all fittings, fixed to walls and ceilings or laid in floors complete all as specified.

S&F 20mm bore steel water tubes medium grade galvanised with all fittings, fixed to walls and ceilings or laid in floors complete all as specified.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft or lose soil complete all as specified.

M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregates) 100mm thick as in subbase etc complete all as specified and as directed

M&L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade pointed with grey cement and pigment complete all as specified.

M&L for Sand cushioning under floors or in foundations including watering and consolidation complete all as specified.

S&F 15mm bore Bib taps fancy type chromium plated, cast copper alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified.

S&F Swivel shower of PTMT any colour for fixing with 15mm pipe (Minimum weight 40gms) complete all as specified.

Dismantling of 100 mm bore cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches and removing as required complete all as specified.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified.

S&F PVC (SWR) bends any radius 110mm bore.

S&F PVC (SWR) bends any radius 75mm bore.

S&F PVC (SWR), junction single, (Single T) equal or unequal 110mm bore.

S&F PVC (SWR), junction single, (Single T) equal or unequal 75mm bore.

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, for laying of pipes, etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified.

M&L for PCC 1:3:6 Concrete bed to drain pipes including packing under and completely surrounding pipes with concrete after they are laid and tested; 100mm bore pipes complete all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified.

S&F 500 litres capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I.

Dismantling water tanks 500 litres capacity and removing to store as directed by engineer-in-charge.

M&L PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundations filling and mass concrete etc. complete all as specified.

M&L for brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified.

M&L rendering 5mm thick in CM 1:4 on ceiling surfaces finished even & smooth without using extra cement complete all as specified.

M&L for rendering 20mm thick on fair faces of brick work or concrete surfaces in CM 1:4, finished even and smooth without using extra cement, including mixing WPC as per manufacturers instructions complete all as specified. (WPC shall be measured seperately)

S&F mild steel bars TMT 6mm to 8 mm dia, cut to length,bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25cm in hard/dense soil complete all as specified.

M&L for RCC M25 (Design Mix) in beams, cantilevers, bressurnmers lintels, roof band, etc complete all as specified.

M&L for RCC M25 (Design Mix) in slabs supported on walls, beams and columns in floors, roofs, landings balconies, canopies, deck slabs and in shelves, etc complete all as specified.

All as per item No. 104.00 above but is in chajjas etc.

M&L formwork to sides and soffits of floor or roof beam beam hauchings. girders. bressum-mers.· lintels. cantilevers. shelves including supports. overhangs. etc. also splays between floors and beams. etc.. for flat rough finished surfaces complete all as specified.

M&L Formwork to chajjas, troughs and similar items including edges for flat rough finished surfaces of concrete all as specified.

M&L formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick, Horizontal or sloping for flat rough finished surfaces complete all as specified.

M&L for broken stone or boulders hardcore of gauge n exc 63mm, deposited, spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard / dense soil complete all as specified.

M&L for screed bed or bedding layer of cement mortar 1:6, 20mm thick for laying floor finishes compelete all as specified

M&L for bricks work with sub class B (old size brick), laid flat in floor in Cm 1:6 complete all as specified

M&L for 10mm thick rendering in Cm (1:4) over RCC roof surface to receive roof treatment finished even and smooth without using extra cement mixed with water proofing compound as per manufacturers instruction (WPC shall be measured and paid separately).

M&L for laying and providing of water proofing treatment over RCC roof all as under:- (a) The dried surface of slab shall be painted with one coat of bituminous primer @0.4 liter/Sqm conforming to IS-3384. (b) Over the primed surface a layer of APP based polymeric membrane of approved manufacturer 3mm thick, reinforced with polyester non woven fabric (weighing not less than 160gms/sqm) shall be laid by torch application method. The side over laps of membrane shall be minimum75mm and the end laps shall be minimum 100mm and sealing all overlaps and joints shall be done as per manufacturer's instruction. (c) The finished surface shall be given one coat of Aluminium paint @ 0.11 Kg/Sqm on top of APP for heat resisting as per manufacturer instruction. Make:-M/S TEXSA INDIA LTD (MOPLY-FP) / M/S STP LIMITED (SUPER THERMOLAY) / M/S PIDILITE INDUSTRIES/ IWL INDIA LIMITED (HYPERPLAS)/CHOKSEY CHEMICALS PVT. LTD.

S&F pressed steel frames (Size-105X60mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified .

M&L preparing new plastered surfaces and applying three coats of white wash on walls complete all as specified.

M&L for preparation of newly plastered surfaces and applying two coats of Weatherproof paint over a coat of alkaline resistant primer complete all as specified and as directed

M&L for 150mm thick PCC 1:3:6, type C2 (using 40 mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L 75mm thick PCC 1:4:8, type D2 (using 40mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L PCC 1:2:4, type B0 (using 12.5mm graded stone aggregate) as in copings, kerbs and the like including weathering, slightly rounded or chamfered angles and throating, as directed incl necessary form work as reqd.

Removing excavated soil/material not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point all as specified and as directed

M&L for sand cushioning for cable in trenches over & under the cables, with sand, as per standard practice with proper compaction complet all as specified and directed by Engr-in-Charge. (Punned thickness shall be considered for payment).

M&L for brick protection over cables inside the trench by using common burnt clay building bricks,sub-class"B" laid dry and flat and width wise along the axis of the trench complete all as specified and as directed by Engineer-in-Charge.

Supply,laying, connecting and testing , Galvanised steel water tubing, light grade, nominal dia 50 mm, for protection of cable as required at site complete all as specified and directed by the Engr-in-charge.

Supplying , Laying, connecting and testing XLPE insulated,sheathed, armoured,heavy duty electric power cable with aluminium conductor suitable for 1100 Volts grade and having cross sectional area 95Sqmm 3.5 Core including taking up old unserviceable cable complete all as directed by Engr-in-Charge.

Supplying , Laying, connecting and testing XLPE insulated,sheathed, armoured,heavy duty electric power cable with aluminium conductor suitable for 1100 Volts grade and having cross sectional area 6 Sqmm 2 Core including taking up old unserviceable cable complete all as directed by Engr-in-Charge.

Supply and fixing thermoplastic polycarbonate street light juntion box suitable for connection of cable , cable size range 10-25 Sqmm cat No KF1616B of make Hansal or equivalant from list of make, size 155X210X92mm which is totally safe, shock proof, impact resistant, weather proof, dust proof, rust proof ,halogen and slica free, having internal embedded gasket technology made of PUR, complete with IP 66degree of protection with cable glands M-25-2 Nos material polymide in and including the following :- Junction box with 5 way Hensel terminal arrangement and 3 terminal block and fixing arrangement of one MCB 6 Amp) and having metric knock out on 4 sides ) - 01 Nos,cable gland -03 Nos, Lock nut - 03 Nos, MCB SP, 6 Amps - 01 Nos complete all as specified and directed.Make : Hansel or equivalent in sintax Industries/C&S.

S&F 20 mm dia (medium grade) Rigid non-metallic PVC conduit fixed with FI clamps, nuts and bolts of suitable size with nuts & bolts for protection of connecting wires, connection from junction box to light fittings, complete all as specified and directed.

Supply & fixing of weather proof pvc insulated copper conductor cable 1.5 sqmm 3 core duly inserting the cable inside the pole including making hole on top and bottom of the steel pole all as directed by engineer-in-charge.

Boring in road/PCC foot path for passing the cable through GI Pipe 50 mm complete all as directed by Engr-in-charge.( GI pipe will be measured seperately)

Dismantling existing ACSR (any size) from over head line complete all as directed by Engr-in-Charge.

Dismantling insulators any type and any size complete all as directed by Engr-in-Charge.

Dismantling of cross arm(made of MS channels / angles etc.) or clamps etc.complete and stacking aside for re-use / replacement all as directed by Engr-in-Charge

Dismantling of stay assembly embedded in concrete and removing materials from site of work complete all as directed by Engineer-in-Charge.

Taking down carefully copper/Aluminum point wiring light fan, socket or power complete (fittings such as switches ceiling roses pendants, regulators, sockets, sketch light fittings, tube light fittings etc. to be measured separately if found serviceable) and removing unserviceable materials from site of work and segregating serviceable materials for safe custody and making good to disturbed surfaces of walls, floors, etc. including disconnecting of ceiling fan/exhaust fan complete all as directed

Point wiring for light/fan/call bell etc. controlled by one switch with 1.50 Sqmm (nominal area) FRLS PVC insulated 1100 volts grade multi stranded copper conductor single core unsheathed cable drawn through and unsheathed single core solid copper conductor cable of size 1.50 Sqmm as earth continuity conductor connected to common earth dolly, including rigid PVC concealed conduit (Medium Grade) of suitable size, with all fittings and accessories including provision of mild steel terminal boxes of suitable size made with 1.2 mm thick mild steel sheet duly galvanised and suitable for fixing switches / sockets / regulators etc. fixed in recess of wall with brass chromium plated screws and cap washer complete for one light / fan point controlled by one switch all as specified and directed.

All as per item No. 136 here-in-before but for 5/6 Amp socket point on independent board.

All as per item No.136 here-in-before but with2.5 Sqmm cable for 15/16 Amp socket point on independent board and 2.50 sqmm solid copper cable for earth continuity conductor.

S&F Switch piano flush type, single pole, one way, 5/6Amp complete all as specified and as directed.

S&F Switch Socket combination, 2-in-1, 3 pin, 5/6 Amps flush type complete all as specified and as directed.

S&F Switch Socket combination, 5-in-1, 5/16 Amps flush type complete all as specified and as directed.

S&F Ceiling rose, surface bakelite, 3 terminals complete all as specified and as directed.

S&F electronic step regulator (speed regulation in 5 steps) suitable for ceiling fan 1200 / 1400 mm sweep 120 watts complete all as specified and as directed.

S&Fmaster LED tube 1200mm, 18w retrofit type with one mounting rail heavy quality complete with side holders. Make:Philips, cat part no TMC 501 P1x T-LED 22W P3241(for mounting rail ) and for LED Tube rod Cat part No. MAS LEDtube 1200mm 18W865 T8 I-2100lm or equvalent make from list of make as approved by GE.

S&F SPN MCB of capacity 32 Amps, 240 volts, complete all as specified and as directed.

Supply and fixing Green line smart luminaire of 40 watt LED street light luminaires with highly efficient lighting in & including mounting bracket made out of GI pipe light grade 32-40mm bore not less than 01 mtr long duly fixed with wall with fixing arrangement such as clamps, nuts, bolts complete all as specified and directed by the Engr in charge make- Philips cat part No BRP 409 LED 040 CW HO MR FG S1 PSU GR or equivalent from list of make as approved by GE

S&F MCB, SP,240 volts, breaking capacity 10 KA, rating 6 to 32 amps, complete all as specified and as directed.

Taking down old serviceable/unserviceable ceiling fan, connecting wire etc and keeping at site for reuse at site after carrying out repiar works to building/rewiring complete all as specified and directed by the Engr-in-charge

Supply and fixing energy efficient, 5 star rated ceiling fan 1200 mm sweep, with all acceesories and connecting up with the ceiling rose with new flexible wire of suitable size complete all as specified and as directed. Make: Usha Energia Star ISI or equivalent make of Havells / Bajaj/ Crompton/ Khaitan

M&L for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of the earth plate not less than 1.5 m below ground level, connected to GI earth wire 4mm dia by means of bolts, nuts,check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of SSR Part-I, connected to earth test point all as specified or indicated including excavation and connected earth work in soft / loose soil, P.C.C 1:3:6 type C-1 as in pit, 20mm dia GI pipe medium grade for watering pipe, 15mm bore GI light grade earth lead protection pipe, 50mm thick R.C.C. 1:2;4 type B-1 cover slab of earth pit reinforced with 8mm dia TMT bars @ 10cm C/C both ways and with handle made out of 10mm dia bars, funnel, strainer,charcoal and testing on completion including dismantling unserviceable earthing complete all as specified and as directed.

S&F Sheet Metal enclosure( IP-43) for SPN DBs,08Ways, Single Door, suitable for mounting DP MCB as incomer & SP MCBs as outgoings, built- in bus bars complete suitable for 240 Volts, AC, 50 Hz supply, and fixed in recess in brick masonary wall all as specified.

M&L for air termination, single pointed aluminium rod 12 mm dia and 300 mm long including taking down old U/S air termination rod all as specified .

M&L aluminium strip 25x3 mm with saddles and fixing screws etc. for roof conductors and down conductors above ground including taking down old U/S almunium strip complete all as specified and directed.

M&L GI strip 32x6 mm for earth continuity conductor including taking down old U/S strip complete all as specified.

M&L for porcelain insulator suitable for fixing earthing strip to the wall / floor etc all as specified.

M&L for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of the earth plate not less than 1.5 m below ground level, connected to 32 x 6 mm aluminium strip by bolts, nuts,check nuts and washers all as shown in electrical plate No 3 of SSR Part-I, connected to earth test point all as specified or indicated including excavation and connected earth work in soft / loose soil, P.C.C 1:3:6 type C-1 as in pit, 20mm dia GI pipe medium grade for watering pipe, 40mm bore GI pipe light grade earth lead protection pipe, 50mm thick R.C.C. 1:2;4 type B-1 cover slab of earth pit reinforced with 8mm dia TMT bars @ 10cm C/C both ways and with handle made out of 10mm dia bars, funnel, strainer,charcoal and testing on completion including dismantling unserviceable earthing complete all as specified and as directed.

M/S Bikash Saha