SPECIAL REPAIRS TO BLDG NO P 7 AT MEANEE LINES SEWAGE LINES TO BLDG NO 279 OF CIW PROVN OF TOILET BLOCK NEAR NO P 19 SEWAGE LINE AT TB I THREE URINALS TO TB I AND ROOF TREATMENT TO BLDG NO T 254 AT NEW TB III UNDER GE NORTH BANGALORE

Amount

B/R WORKS

Demolition of cement concrete(unreinforced) of any description and in any position not otherwise specifically provided for and removal of debris off the premises complete all as specified and as directed.

Demolition Reinforced Cement Concrete as roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work and removal of debris off the premises complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the the premises complete all as specified and as directed.

Roughening the surfaces of old concrete floors by picking, sweeping cleaning and washing down with water to remove dust, etc., all as specified and as directed.

Non skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20 mm thick screed bed in CM (1:4) over and including 25 mm thick PCC (1:2:4), type B0 using 12.5 mm graded stone aggregate as in levelling concrete all as specified and as directed.

Matt finish ceramic coloured tiles 7-8mm thick (square / rectangular) area of each tile exceeding 0.11 sqm but n.exc. 0.18 sqm as in floors set and jointed in neat cement slurry and pointed in coloured cement to match over and including 20 mm thick screed bed in CM (1:4) over and including 25 mm thick PCC (1:2:4), type B0 using 12.5 mm graded stone aggregate as in levelling concrete all as specified and as directed.

Glazed coloured ceramic tiles as in vertical surfaces 350 x 250x 7 mm/ 450 x 350 x 7 mm/ 300x450x7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including backing coat 10mm thick in CM (1:3) on fair faces of brick work or concrete surfaces complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid dry and pointed in any mortar complete all as specified and as directed.

Demolition of brick work or stone / PCC /boulder masonry built in cement mortar or lime mortar including all quions, arches, pillars but excluding ashlar facing, dressed stone work of any description all as specified and directed.

Brick work using sub class 'B' bricks in half brick walls built in CM (1:4), straight or curved on plan exc. 6m mean radius complete all as specified and as directed.

Precast cement concrete block masonry with solid blocks exc. 10 cm in width and setting in cement mortar (1:4) type C1 1:3:6 ( using 20 mm graded aggregate) complete all as specified and as directed.

Taking down cement plaster on brick / stone / concrete surface including wall tiling and hacking out joints hacking for key scrubbing down with water etc complete all as specified and as directed.

10mm thick rendering on brick or concrete surface in cement mortar (1:6) and and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

Rendering 5mm thick on ceilings of of concrete surfaces in CM (1:3) all as specified surfaces finished even and smooth without using extra cement on ceiling

Plain Cement Concrete (1:5:10), type E-2 using 40mm graded stone aggregate as in sunken floor fillings, complete all as specified and as directed.

Rendring 10 mm thick in CM (1:3) mixed with and including CEBEX 100 (FOSROC) or equivalent as per manufatures instructions and finishing the surfaces even and smooth with using extra cement as in sunken floor etc complete all as specified and as directed.

Brush bond RFX of FOSROC or equivalent applied as in vertical surfaces of sunken floors all as per manufacturers instructions complete all as specified and as directed.

Preparation of new or previously un treated plastered surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of oil bound emulsion distemper over a coat of alkali reistant primer on wall complete all as specified and as directed.

Taking down chowkat (without taking off shutter from the frame)area not exc. 1.5 sqm each including making good the disturbed surface in PCC (1:2:4) type B0 or in CM (1:3) all as specified and as directed.

All as per Sl Item No 1.019 above but area exc. 1.5 sqm and n.exc. 4 sqm each.

Taking down shutter only of any description area exc. 1 sqm but n.exc. 2 sqm each all as specified and as directed.

Taking down and refixing of shutters of any description area exc. 1 sqm and n.exc. 2 sqm each in same opening after necessary repairs all as specified and as directed.

Pressed steel frames of size 125 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges lock strike plate, etc complete all as specified and as directed.

Pressed steel frames of size 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges lock strike plate, etc complete all as specified and as directed.

Door bottom sweep,having rain drip nylon brush with alluminium casing fixed with screws to door shuter to arrest insects, moisture etc., all as specified and as directed.

Factory made second class hard wood plain, framed panelled shutters 35mm thick with panels of timber flat on both sides (feather edged) or of 12mm thick veneered particle board medium density wood particle tone veneers, fixed to chowkhat all as specified and as directed.

Factory made second class hard wood 35mm thick glazed and skelton shutters, open rebated and prepared to recive gauge, including stainless steel wire cloth and fitted to chowkats all as specified and as directed.

Mild steel tower bolts 150 mm long stove enameled black with bright bolt complete all as specified and as directed.

Mild steel sliding bolt 300 mm long plate type stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fix complete all as specified and as directed.

Mild steel butt hinges 100 mm, long medium weight, cold rolled complete all as specified and as directed.

Mild Steel pressed handles 150mm size oval type stove enameled black complete all as specified and as directed.

Cutting holes in brick walls thickness exc. one brick but not exc. two bricks in cement mortar and making good dimantled portion in CM(1:3) or plain cement concrete (1:2:4) type B1 as required complete all as specified and as directed.

18 to 20mm thick Plywood, grade BWP, type BB fixed with screws to timber frame work complete all as specified and as directed.

0.9mm thick decorative laminate type 1, of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturers instructions complete all as specified and as directed.

Ball catches with 8mm dia steel ball and brass body and striking plate including letting in and fixed complete all as specified and as directed.

Mild steel continuous piano hinges, width of flap 30mm bright finish or electrogalvanised complete all as specified and as directed.

18/20 mm wide edge bands 1mm thick on edges of shutters complete all as specified and as directed.

Steel windows of box type, with frame of 80 x 60mm and 1.25mm profile sheet with box type shutters consisting of inside glazed shutter and out side gauged shutter with steel handle, telephonic peg stay complete with glazing bars of 08 Nos with 10 x 10mm mild steel square guard bars in equal spacing, devotailed or welded all as per TD Drg No. 539 sheet 1/3 to 3/3 including one coat of red oxide primer all as specified and directed. NOTE :- PCC in frame, glass pane and wire mesh will be measured andpaid separately under relevant items.

Steel ventilators of box type, with frame of 80 x 60mm and 1.25mm thick profile sheet with top hung shutters(half fixed) including hinges, steel peg stay, complete with glazing bars and 10 x 10 mm square guard bars in equal spacing, devoited or welded including one coat of red oxide primer all as specified and directed. NOTE :- PCC in frame, glass pane and wire mesh will be measured andpaid separately under relevant items.

Pin headed glass 3mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane and all as specified and as directed.

Plain sheet glass 3mm thick, ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane and all as specified and as directed.

Galvanized mild steel wire cloth 0.56mm nominal dia and average width of aperture 1.18mm and fixed in repairs with tinned tack or galvanized wire staple all as specified and as directed.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 and fixed with stainless steel wire staples all as specified and as directed.

Factory made solid PVC moulded door shutter , 28 to 30mm thick (stiles) with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face and 2mm thick plain colour PVC sheet on back face supplying and fixing in frame at site as per specification & drawing.

Solid PVC door frame of size 50mm x 47 mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube fixed to wall all as specified and as directed.

Aluminium anodised tower bolt 150mm size complete all as specified and directed.

Aluminum Butt hinges, 100 mm long, type C21 complete all as specified and as directed.

Aluminium anodized cast type handles 125 mm long complete all as specified and as directed.

Tubular towel rail, 20mm dia, D type, 60cm long between flanges of brass chromium plated fixed in repairs complete all as specified and as directed.

Hat and coat hooks, solid body, 175mm to 250mm made out of brass complete all as specified and as directed.

Stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x 420mm with bowl size 410mm x 330nun x 160mm including PVC waste pipe 32/40 mm dia and 1200 mm long complete fixed in repairs all as specified and as directed.

Looking mirror of size 600x450mm with PVC sheet frame and back supported with 6mm thick AC building board or plywood sheet complete all as specified and as directed.

Preparation of old painted wooden surfaces of any description exceeding 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Preparation of new or previously untreated steel and iron surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel over a coat of red oxide primer, complete all as specified and directed.

Reinforced Cement Concrete (nominal mix), type B-1, (1:2:4) using 20mm graded stone aggregate as in slabs supported on wall, beams and columns in floors roofs, landings, balconies, canpoies, deck slabs, shelves and the like complete all as specified and directed.

TMT steel bars 10mm dia and over, cut to length bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Rotational moulded polythene water storage tank (cylindrical vertical with closed top) with ISI mark embosed on it, hoisted and fixed in position complete all as specified in SSR part I capacity of tank 500 ltrs capacity Including dismaling old tank complete all as specified and as directed.

Disconnecting existing water tanks setting aside (or lowering if required) for repairs cleaning etc and hoisting if required connecting and refixing in position cleaning, repairing and removing all scale and dirt etc., from tanks and mouths of circulating pipes capacity exc. 250 and not exc. 500 ltr complete all as specified and as directed.

Demolition of existing roof treatment of any type including cement plaster 10 mm thick and PCC 25mm thick and providing Roof treatment with screed bed/rendering 10mm thick in CM (1:4) over PCC(1:2:4) type B0, 25mm thick mixed with and including supply of approved water proofing compound as per manufacturers instructions, removing all loose gravel, dirt, oil, grease and foreign materials by jet or dry air, cleaning the surfaces mechanically or by grinding to make it smooth and providing 50mm x 50mm coving at the corners with PMC mortar, applying prime coat with anti root primer consisting of Shali prime WP WB @ 400gm/sqm, first coat of water based UV resistent elastomeric modified PU liquide membrane consiting of Shaliurethane(R) BTD of STP @ 1 Kg/ Sqm, spreading the fibre glass net of 45 gsm over the entire area, second coat of Shaliurathene(R) BTD of STP @ 1 Kg/ Sqm for elastomeric seamless water proof membrane in two coats to a final DFT of 1.5mm thick having an elongation capacity of over 500% which conforms to ASTM C 836 and ASTM D 6083, complete all as specified and as directed.

Complete removal of existing treatment on walls by preparation of plaster surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of oil bound emulsion distemper of approved tint over a coat of alkali reistant primer on walls complete all as specified and directed.

Forming jambs etc to openings including toothing and properly bonding into old brickwork also facing, jointing and pinning to match the existing work complete in CM (1:6) all as specified and as directed.

Preparation of new plastered or unplastered ceiling surfaces of any description and applying three coats of white wash on ceiling all as specified and as directed.

Complete removal of existing treatment on walls and preparation of plaster surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of cement based paint of approved tint over a coat of alkali resistent primer complete all as specified and as directed.

Soap dish, fancy type of brass, Chromium plated complete all as specified and as directed.

Bib taps, 15mm dia, fancy type, cast copper alloy, chromium plated screwed down, screwed for iron pipe or for brass ferrule fixed as in repairs complete all as specified and as directed.

PVC connections 15 mm size with PTMT nuts of length 600mm fixed as in repairs all as specified and as directed.

Brass chromium plated overhead shower rose 125 mm size with or without swivel joints, 75mm dia round shower, including fixing to 15mm dia steel pipe or union fixed in repairs complete all as specified and as directed.

Stop valves, 15mm dia, fancy type, cast copper alloy, chromium plated with long shank and cup concealed type screwed down, screwed for iron pipe or for brass ferrule fixed as in repairs complete all as specified and as directed.

PVC health faucet suitable for pedastal pattern water closet with flexible pipe of length 1.5 Mtr all as per Prayag Cat No. 452 or techno commercially equivalent makes specified in PS complete all as specified and as directed.

Vitreous china wash hand basin, white, flat back size 550x400mm including CI brackets, PTMT waste coupling and PVC waste pipe 75 cm long and 15mm dia PVC connections including pillars taps 15mm dia, fancy type, cast copper alloy chromium plated screwed down high pressure with lettered Hot or Cold with long screwed shanks, screwed for iron pipe or for brass ferrule and including PVC waste pipe 32/40 mm dia, 1200 mm long etc., complete fixed in repairs all as specified and as directed.

Vitreous china wash down water closet pan (pedestal pan) including fixing bolts, PVC flushing cistern 10 Ltr capacity, with flush pipe anti syphonage pipe, plastic water closet seat cover, black closed pattern with flat bottom and cover with mild steel chromium plated or aluminium hinging device etc complete fixed in repairs all as specified and as directed.

Grating doom 125/75 mm dia with waste hole of PTMT (minimum weight 40 gms) fixed in repairs all as specified and as directed.

Two way bib taps 15mm dia, standard PTMT, any colour screwed for iron pipe and fixedall as per Prayag Cat No. 129-E or techno commercially equivalent makes specified in PS complete all as specified and as directed.

Taking up or down steel tubing 15mm dia and connections including cleaning for refixing or removal to store all as specified and as directed.

Taking up or down steel tubing 20 mm dia and connections including cleaning for refixing or removal to store all as specified and as directed.

20mm dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings, fixed to wall, ceiling or laid in floors complete all as specified and as directed.

Stainless steel plate rack made out of 1 mm thick stainless steel sheet, over all size 900mm x 900mm x 230mm with shape, capacity of utensiles and pattern complete all as specified and as directed.

Drapery rods of high strength aluminum rod, powder coated thickness 40-60 micron of outer dia 28mm and inner dia 24.5mm with providing 2 Nos brackets (projected type / wall to wall) and finials as approved all as specified and as directed.

Rolled mild steel framed work as in doors or gates of angle other section etc complete incl necessary welding using steel Fe 410 -W all as specified and as directed.

Taking down PVC (SWR) pipes 110mm dia complete all as specified and as directed.

Taking down PVC (SWR) pipes 75mm dia complete all as specified and as directed.

110 mm bore PVC (SWR) pipes, type 'B' single socketed in any length with rubber ring joints fixed to wall including PVC clamps all as specified and as directed.

110 mm bore PVC (SWR) pipes, type 'B' single socketed in any length with rubber ring joints laid in trenches or floors all as specified and as directed.

75 mm bore PVC (SWR) pipes, type 'B' single socketed in any length with rubber ring joints fixed to wall including PVC clamps all as specified and as directed.

75 mm bore PVC (SWR) pipes, type 'B' single socketed in any length with rubber ring joints laid in trenches or floors all as specified and as directed.

110mm bore PVC (SWR) vent cowl, type 'B' all as specified and as directed.

75mm bore PVC (SWR) bends with access door type 'B' all as specified and as directed.

110mm bore PVC (SWR) bends with access door type 'B' all as specified and as directed.

110 mm bore PVC (SWR) branch piece (double Y) equal or unequal with access door, type 'B' all as specified and as directed.

110 mm bore PVC (SWR) junction single (single T) equal or unequal with access door, type 'B' all as specified and as directed.

PVC (SWR) multi floor trap 75mm dia with grating type 'B' including joint with solvent cement all as specified and as directed.

Hard core of guage n.exc. 63mm deposited spread and levelled, laid in layers n.exc. 15cm thick, watered and rammed to a true surface using broken boulders all as specified and as directed.

75 mm thick plain cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) as in paving/ plinth protection laid in panels including necessary form work, finished rough surfaces of concrete complete all as specified and directed.

Plain Cement concrete (1:4:8), type D2, using 40mm graded stone aggregate as in sub bases of floors, 75mm thick, complete all as specified and directed.

Chequerred cement concrete tiles with grey cement and pigment, 300x300x25mm thick, set, jointed and pointed in neat cement slurry with grey cement and pigments to match the colour of tiles over 20mm thick screed bed in CM (1:4) complete all as specified.

Machine cut Granite stone slab 18 -20mm thick, black colour, laid over and including 15mm thick screed bed in cement mortar (1:4) bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing, rounding to edges of stone slabs at one edge all as specified and as directed.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth and getting out in hard/dense soil complete all as specified and as directed.

Plain Cement Concrete as in foundation filling and mass concrete (1:4:8), type D-2, using 40 mm graded stone aggregate complete all as specified and as directed.

Reinforced Cement Concrete, M-25 (design mix)using 20mm graded stone aggregate as in foundation footing complete all as specified and as directed.

Reinforced Cement Concrete, M-25 (design mix)using 20mm graded stone aggregate as in columns complete all as specified and as directed.

Reinforced Cement Concrete, M-25 (design mix)using 20mm graded stone aggregate as in beams and slabs complete all as specified and as directed.

Use and waste of form work to sides of footings and plinth beams complete all as specified and as directed.

Use and waste of form work to sides of columns complete all as specified and as directed.

Use and waste of form work to sides of lintles, tie beams, roof slabs and chajja complete all as specified and as directed.

TMT steel bars 8mm dia, cut to length bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

TMT steel bars 6mm to 8mm dia as in stirrups cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and as directed.

Returning, filling in excavated soil, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in hard / dense soil etc complete as specified as directed.

Removing the excavated material to a distance exc. 50m but n. exc. 100m and depositing where directed at a level n. exc. 1.5m above the starting point.

Plain Cement Concrete,(1:2:4), type B0, 25mm thick as in damp proof course with using including supply of approved integral liquid water proofing compound as per manufacturers instructions complete all as specified and as directed.

Precast cement concrete block masonry with solid blocks n.exc. 10 cm in width and setting in cement mortar 1:4 type B1(1:2:4), using 20 mm graded stone aggregate complete all as specified and as directed.

Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

Hard core of guage n.exc. 63mm deposited spread and levelled, laid in layers n.exc. 15cm thick, watered and rammed to a true surface using broken boulders all as specified and as directed.

Plain Cement concrete (1:4:8), type D2, using 40mm graded stone aggregate as in sub bases of floors complete all as specified and directed.

Plain Cement Concrete (1:2:4), type B0, using 12.5mm graded stone aggregate as inlevelling concrete complete all as specified and directed.

Non skid ceramic coloured printed tiles 7 to 8mm thick(square/ rectangular) area of each tile exc. 0.06 sqm but not exc. 0.11sqm as in floors, set and jointed in neat cement slurry and pointed in white cement mixed with colour pigment to match over including 20 mm thick cement screed in CM(1:4) complete all as specified and as directed.

Glazed coloured ceramic tiles as in vertical surfaces 350 x 250x 7 mm/ 450 x 350 x 7 mm/ 300x450x7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including backing coat 10mm thick in CM (1:4) on fair faces of brick work or concrete surfaces complete all as specified and as directed.

Rendering 15mm thick in cement mortor (1:4) on fair faces of brick or concrete block masonry surfaces finishing the surfaces even and smooth with out using extra cement complete all as specified and as directed.

Rendering 10mm thick in cement mortor (1:4) on ceiling surfaces finishing the surfaces even and smooth with out using extra cement complete all as specified and as directed.

Preparation of new or prevously plastered wall surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of cement based paint of approved tint over a coat of alkali resistent primer complete all as specified and as directed.

Preparation of new or prevously plastered ceiling surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of white wash over one coat of chalk whiting complete all as specified and as directed.

Preparation of new or prevously plastered wall surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of white wash over one coat of chalk whiting complete all as specified and as directed.

PTMT butt hinges, 100 mm long and fixed with steel screwscomplete all as specified and as directed.

PTMT tower bolts, 150 mm long and fixed with steel screws complete all as specified and as directed.

PTMT door handle, 150 mm long and fixed with steel screws complete all as specified and as directed.

300mm long Aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

Rotational moulded polythene water storage tank (cylindrical vertical with closed top) with ISI mark embosed on it, hoisted and fixed in position complete all as specified in SSR part I capacity of tank 2000 ltrs capacity Including dismaling old tank complete all as specified and as directed.

20mm dia Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed(Min weight 20mm-210 gms) all as specified and as directed.

Gun metal gate or globe valves 25 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

Preparation of new or previously untreated wooden surfaces of any description not other wise described over 10cm width or girth applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Plain Cement Concrete (1:2:4), type B1, using 20mm graded stone aggregate as in copings, bed blocks, hold fasts etc., complete all as specified and directed.

Soap dish, PTMT fancy type ,all as per Cat Part No1951 of Prayag or equivalent makes specified in PS fixed to wall as per manufacturers instructions complete all as specified and as directed.

Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe complete all as specified and as directed.

Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including PVC (SWR) P trap connecting to flush pipe and to anti syphonage pipe, PVC valveless, syphonic action type flushing cistern, low level, white,with inlet, ball valve, float and handle 10 ltrs capacity incl brackets, etc. complete including making good to floor fixed complete all as specified and directed.

Vitreous china wash down water closet pan (pedestal pan) including fixing bolts, flush pipe anti syphonage pipe, plastic water closet seat , coloured, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device etc complete of CERA model Cat Pt No. 2008 & 2308 and mild steel chromium plated or aluminised hinging device, PVC valveless, syphonic action type flushing cistern, low level, white,with inlet, ball valve, float and handle 10 ltrs capacity incl brackets and stop valve fancy type cast copper alloy chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed 15mm dia complete all as specified and as directed.

Vitreous china wash basin white flat back size 550x400mm excl chain and plug and porcelain stopper but incl CI bracket, PTMT waste coupling and PVC waste pipe 75 cm long and 15mm dia PVC connection Pillars taps fancy type cast copper alloy fancy type,Stop valve fancy type chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed 15mm dia etc complete all as specified and as directed.

25mm dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings, fixed to wall, ceiling or laid in floors complete all as specified and as directed.

PVC (SWR) Gully trap 125/110 mm dia, setting and jointing with solvent cement including jointing to waste pipe fixed in cement concrete type complete all as specified and as directed.

Bib taps standard of PTMT, any colour screwed for iron pipe suitable for 15mm dia completed all as directed.

Stop valves, standard of PTMT, any colour screwed for iron pipe suitable for 15mm dia complete all as directed.

PTMT overhead shower with shower arm length 225 mm with flange all as per Prayag Cat No 1814-C or equivalent all as specified and as directed.

Brass Chromium plated tubler towel rail, 20mm dia D type 600mm long between flanges complete all as specified and as directed. MAKE:- CERA Model no: CG303 or techno commercially equivalent maks specified in PS.

Roof treatment by providing screed bed/rendering 10mm thick in CM (1:4) over and including plain cement concrete (1:2;4) type B0, 25mm thick mixed with and including supply of approved water proofing compound as per manufacturers instructions, removing all loose gravel, dirt, oil, grease and foreign materials by jet or dry air, cleaning the surfaces mechanically or by grinding to make it smooth and providing 50mm x 50mm coving at the corners with PMC mortar as above, applying prime coat with anti root primer, Shali prime WP WB @ 400gm/Sqm, first coat of water based Uv resistent elastomeric modified PU liquide membrane, Shaliurethane(R) BTD of STP @ 1 Kg/ Sqm, spreading the fibre glass net of 45 gsm over the entire area, second coat of Shaliurathene(R) BTD of STP @ 1 Kg/ Sqm for elastomeric seamless water proof membrane in two coats to a final DFT of 1.5mm thick having an elogation capacity of over 500% which conforms to ASTM C 836 and ASTM D 6083, complete all as specified and as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 150mm internal dia pipe complete all as specified and as directed.

Precast Reinforced Cement Concrete (1:2:4), type B1, using 20mm graded stone aggregate as in cover slabs of man holes, chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain facesset in CM (1:4) complete all as specified and as directed.

Plain Cement Concrete (1:2:4), type B1, using 20mm graded stone aggregate as in benching of manholes, surface channels and drains complete all as specified and as directed.

Rendering 15 mm thick on brick work or concrete surfaces in CM (1:4), using integral water proofing compound as per manufacturers instructions, finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and as directed.

Reinforced Cement Concrete pipes, class NP2, of 200mm dia laid in trenches and jointed complete with collars all as specified and directed.

Reinforced Cement Concrete pipes, class NP2, of 150mm dia laid in trenches and jointed complete with collars all as specified and directed.

Plain cement concrete (1:4:8) type D2 using 40 mm graded stone aggregateas in bed to drain pipes including packing under and haunching against the sides of SWG/RCC pipes after they are laid and tested suitable for 200mm dia bore pipe all as specified and as directed.

Plain cement concrete (1:4:8) type D2 using 40 mm graded stone aggregateas in bed to drain pipes including packing under and haunching against the sides of SWG/RCC pipes after they are laid and tested suitable for 150mm dia bore pipe all as specified and as directed.

Providing plain cement concrete 1:3:6 type C-1, 75mm thick using 40mm graded stone aggregate as in plinth protection/path finising the surface even and smooth without using extra cement all as specified

Excavation in trenches not exceeding 1.5 mtr wide, depth exceeding 1.5 mtr and not exc. 3.0 mtr and getting out in hard/dense soil complete all as specified and as directed.

Demolition and breaking up drains pipes(Salt glazed ware) set in cement mortar internal dia of pipe 150 mm complete all as specified and as directed.

Demolition and breaking up in drains pipes(Salt glazed ware) set in cement mortar internal dia of pipe 200 mm complete all as specified and as directed.

Demolition of RCC man hole covers and similar works etc complete all as specified and as directed.

PVC (SWR) pipes 150 mm dia, 6 kg/sq.cm pressure rating single socketed in any length jointed with solvents tested all as specified and as directed.

Removing the excavated material to a distance exc. 250m but n. exc. 500m and depositing where directed at a level n. exc. 1.5m above the starting point.

Cutting of existing road surface Including WBM for sewage line where ever required and making good thesurfaces with PCC(1:2:4) complete as specified and as directed.

Plain Cement Concrete (1:3:6), type C1, using 20mm graded stone aggregate as in copings, water troughs and the like including weathering, slightly rounded or chamfered angles and throughs complete as specified and as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 200mm internal dia pipe complete all as specified and as directed.

Rolled mild steel as in roof trusses (framed), trussed purlins crane gantries rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces cleats etc.,steel conforming to Fe 410-W (Gde-E- 250) quality-A all as specifeid and as directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws as specifed and as directed.

Plain Cement concrete (1:3:6), type C2, using 40mm graded stone aggregate as in sub bases of floors, 100mm thick, complete all as specified and directed.

18 -20mm thick Granite(of any type) tiles machine cut in skirting/dado / urinal partition incl necessary fitting arrangements and nosing and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing complete all as specified and directed.

75mm bore PVC (SWR) vent cowl, type 'B' all as specified and as directed.

E/M WORKS

Taking down carefully aluminium / copper wiring / power point wiring (light, fan, socket or power) complete including fittings such as switches, ceiling roses, regulators, sockets, light fittings, fans, bell pushs, bells, regulators etc and making good the disturbed surface of walls, ceiling etc all as specified and as directed.

Point wiring complete with 1.5 sq.mm single core FRLS PVC insulated unsheathed, 1100 volts grade, multi stranded copper conductor cable conforming to IS 694 drawn through and including non-metalic rigid PVC conduit of suitable size, medium grade including necessary accessories surface type / concealed run on walls/ ceiling with MS terminal boxes fabricated with 1.6 mm thick MS sheet surface mounted/ concealed on walls with industrial laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch socket outlets, fan regulators etc., including provision of 1.5 sq.mm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly all as specified and as directed for one light point controlled by one switch.

All as per Sl Item No. 2.002 here in before but for one fan point controlled by one switch / regulator.

All as per Sl Item No. 2.002 here in before but for one bell point controlled by one switch.

All as per Sl Item No. 2.002 here in before but for one light point controlled by two two way switches.

All as per Sl Item No. 2.002 here in before but for one 3 pin socket out let 5 Amps on independent board.

All as per Sl Item No. 2.002 here in before but for one 3 pin socket out let 5 Amps on same board with other switches.

Point wiring complete with 2.5 sq.mm FRLS single core PVC insulated unsheathed cable 1100 volts grade multi stranded with copper conductor conforming to IS 694 drawn through and incl non-metalic rigid PVC casing and capping incl accessories surface type/ concealed run on walls/ ceiling incl MS terminal boxes fabricated with 1.6 mm thick MS sheet surface mounted/ concealed on walls with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch socket outlets, fan regulators etc., incl provision of 2.5 sq.mm FRLS PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly all as specified and as directed. NOTE FOR SL ITEM NO. 2.002 to 2.008 :- (i) The earth wire for the points in the same circuit can be looped from point to point. (ii) Earth wire shall be taken inside the conduit. (iii) Cost of terminal box is deemed to be included in the item rate quoted for point wiring. (iv) Cost of a circuit of any length of cable from DB to any switch/ socket board to be included in point wiring.

Switch Piano, flush type, one way, 5 Amps, 240 Volts single pole with ISI marked complete all as specified and as directed.

Switch Piano, flush type, two way, 5 Amps, 240 Volts single pole with ISI marked complete all as specified and as directed.

Bell push, flush type, one way, 5 Amps, 240 Volts single pole with ISI marked complete all as specified and as directed.

Switch socket combination 3 & 2 pin, 5 Amps, 240 Volts, flush type multipurpose controlled by one switch all as specified and as directed.

Switch socket combination 2 in 1, 3 pin and 2 pin, 5 and 15 Amps flush type, universal complete all as specified and as directed.

Lamp holder angular type, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

Buzzer, Ding dong AC, 230 volts, single pole all as specified and as directed.

Ceiling rose surface type, PVC/ polycarbonate, isolated body with three terminals complete all as specified and as directed.

Sub main wiring complete with two runs of 4 sq.mm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable with one run of 4 sq.mm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 25 mm dia non metallic rigid PVC conduit and conduit accessories including taking down the old submain wiring all as specified and as directed. NOTE :- Two runs of cable and one run of earth wire with PVC conduit shall be measured as one unit for payment purpose.

LED batten fittings 4 feet long, suitable for indoor application of system wattage 18 /20 watt , CCT 6500 K , luminous efficiacy 100 Lm /watt , PF > 0.9 etc including electrical connecion from ceiling rose with 3 core 1.0 sqmm sheathed cable all as per Wipro Cat part No: LL20 -221- XXX- 65 NE /Bajaj Cat No. 830192 or techno commercially equivalent makes specified in PS complete all as specified and as directed.

LED batten fittings 2 feet long, suitable for indoor application of system wattage 10 watt , CCT 6500 K, luminous efficiacy 100 Lm /watt, PF > 0.9 etc including electrical connecions from ceiling rose with 3 core 1.0 sq.mm sheathed cable all as per Wipro Cat part No: LL20 -111- XXX- 65 NE / Bajaj Cat No. 830203 or techno commercially equivalent makes specified in PS complete all as specified and as directed.

LED building security light of protection IP-66, system wattage 30 Watt, CCT -5700 K , PF >0.9, etc complete including GI bracket made out of 40mm dia medium grade pipe of 1 mtr length bend to shape fitted at pole / building including connections with sheathed cable of 2.5 sq.mm 3 core all as per Wipro Cat part No: LR-02-291-XXX -57-XX or techno commercially equivalent makes specified in PS complete all as specified and as directed.

LED lamp of 9 watt suitable to fit in angle holder all as specified and as directed.

Vertical DB VTPN with MCCB as incomer 4 ways double door with provision for and including supply of MCCB TP 125 Amps in 16 KA as incomer, IP 43 protection , conforming to IS-13032, universal mounting with copper bus bar, neutral link, earth link, earthing studs, detachable gland plates with knockouts on both sides all as per INDOASIAN OPTIPRO Cat No.811888 or techno commercially equivalent makes specified in PS complete all as specified and as directed.

MCB DB SPN 8 way, double door,with 200 Amps rated busbar 240 V, AC, 50 Hz, IP-43 protection conforming to IS-13032, universal mounting with copper bus bar, neutral link, earth link, earthing studs, detachable gland plates with knockouts on both sides all as per Indo Asian Optipro Cat No.8119807 or techno commercially equivalent makes specified in PS including taking down the existing complete all as specified and as directed.

RCCB double pole as per IEC 12640, 240 volts, degree of protection IP-20, short circuit current 10 KA, current carrying capacity 25 Amps, sensitivity 30 mA complete including taking down the existing complete all as specified and as directed.

MCB single pole, 240 volts 5 to 40 Amps complete including taking down the existing complete all as specified and as directed.

Taking down ceiling fan care fully , dismantling the blades, down rods, painting the ceiling fan complete in situ with synthetic enamel paint by spraying including filling cavities with one filler coat after claeaning the dust etc, writing MES No and refixing the fan in the exisiting position complete with connection of fan from ceiling rose with 1.0 sq.mm 3 core shaethed cable all as direceted.

Dismantling the ceiling fan of any size and sweep at site or workshop, taking out the burnt winding, rewinding the stator winding with enamelled copper wire of exsiting guage including replacement of ball bearings, capacitor , bush etc , reassembling the ceiling fan after proper oiling and greasing all as specified and directed. NOTE :- Transportation from the site and workshop shall be deemed to included in the quoted rate.

Fan regulator 5 Amps, Stepped, electronic and flush type fixed on the exisiting laminated sheets all as specified and as directed.

Earthing complete with galavnised steel earth plate electrode 600mm x 600mm x 6mm thick burried directly in ground vertically to a depth not less than 2.25 meter below ground level with top edge of earth plate at a depth not less than 1.5 mtr connected to and including galavnised iron wire of 4 mm dia as earth lead up to 7.5 mtr long by means of nuts, bolts, thimbles, check nuts and washer etc made of galavnised iron connected to earthing test point through protection pipe light grade of 20 mm dia all as shown in electrical plate No 3 of SSR Part - I, 2009 and as specified or indicated and testing on completion including earth work and excavation in any type of soil PCC (1:3:6) type C 1 chamber, precast slab 40mm thick in Reinforced cement concrete (1:2:4) type B 1 with 8 mm dia TMT bars reinforced at 10 cm centre to centre both ways including funnel with watering pipe of 20 mm dia medium grade ,wire mesh and lugs, including test point, cable connected with suitable size copper lugs and complete all as specified and as directed.

All as per Sl Item No. 2.029 above but including takin down the existing earthing.

Removing the existing single phase energy meter 4 Nos carefully by disconnecting all the electrical connections, removing the exisitng wooden box /board providing industrial laminated sheet of 5 / 6 mm thick of existing box / board size for fiixng 4 energy meter and one VTPN DB, fixed on wall with proper fxing arrangement including refixing of energy meter, with all necessary electrical connections etc., complete all as specified and as directed.

Galvanised iron pipes 20 mm dia, medium grade with all required necessary fittings and fixed complete to walls and ceilings or laid in floors including taking down the existing complete all as specified and as directed.

Gun metal gate valves 20mm dia, with iron wheel head ISI Mark embosed on it, screwed both ends fixed in repairs complete fixed in repairs all as specified and as directed.

MCB single pole and neutral 20 to 40 Amps 240 volts, 10 KA rupturing capacity providing in DB complete all as specified and as directed.

Exhaust fans AC, heavy duty, single phase 230/ 240 V of RPM 1400, air delivery 750 CHM of size 300 mm sweep , fixed to wall with nuts and bolts etc including electrical connection from the ceiling rose to fan by using 3 core 1.5 sq.mm sheathed cable with provision of metal louvers filtted outsdie including. cutting of the existing wall , making of the wall to match with the exsiting surface all as per Bajaj Cat No.FRESHEE MK II product code : 70003 or techno commercially equivalent makes specified in PS all as specfied and as directed

LED Building security light fittings 25 Watts, housing made of die cast aluminium in gray finish with clear acrylic and cast aluminium pipe mounting attachment, IP-66 degree of protection with all accessories and pre wired complete including PVC three core flexible copper Conductor cable form ceiling rose to connector of fittings including GI bracket made of GI pipe light grade 40 mm dia 1.0 mm long bend in to shape fitted to the wall with GI clamps of size 32 x3 mm all as per Wipro Model No: LR02- 291-XXX-57-XX techno commercially equivalent makes specified in PS all as specified and as directed.

Excavation in trenches in hard / dense soil not exc 1.5 mtr wide and not exc 1.5 mtr in depth for laying of cables or pipes / errection of pole etc complete all as specified and as directed.

Returning, filling in trenches incl spreading leveling watering and well ramming in layers with hard / dense soil not exc 25 cm thick in each layer complete as specified and as directed.

Removing excavated soil to a distance exceeding 250 mtr butnot exc. 500m and depositing where directed at a level not exc. 1.5 mtr above the starting point complete all as specified and as directed.

Sand cushioning in layers for cables in trenches / ducts for cable including consolidation complete all as specified and directed. NOTE: Punned thickness will be measured for payment purpose.

Bricks, sub class 'B' of old size 230 mm x 115 mm x 75 mm laid in trenches for cable protection all as specified and directed.

XLPE insulated screened PVC bedded galvanised steel strip or wire armored, electric power cable (heavy duty) 2 core x 16 sq.mm 1100 Volts grade with stranded aluminium conductor laid in trenches complete all as specified and as directed.

Mild steel galvanized pipe light grade for protection and passing of LT cable fixed to poles/walls/laid under floor/roads complete including fittings/clamps as required at site all as specified for size of 40mm bore dia all as specified and as directed.

Cutting existing steel tubing of size 40 or 50 m dia for alterations or additions all as specified and as directed. NOTE:-Each cut shall be measured.

Screwing existing steel tubing for alterations or additions of size 40 or 50 mm dia or lengthening screw on pipe to form connector all as specified and as directed.

Galvanised iron pipes 40 mm dia, medium grade with all required necessary fittings and fixed complete to walls and ceilings or laid in floors including taking down the existing complete all as specified and as directed.

Galvanised iron pipes 25 mm dia, medium grade with all required necessary fittings and fixed complete to walls and ceilings or laid in floors including taking down the existing complete all as specified and as directed.

25mm dia Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed all as specified and as directed.

SAI CONSTRUCTIONS

Shanthi Construction