boot ankle textile jungle boot direct moulded pu sole in pairs Boot Ankle Textile Jungle Boot Direct Moulded Pu Sole In Pairs ( 2524 ) Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values specification Governing Specification Conforming to FDDI (FOOTWEAR DESIGN & DEVELOPMENT INSTITUTE

boot ankle textile jungle boot direct moulded pu sole in pairs Boot Ankle Textile Jungle Boot Direct Moulded Pu Sole In Pairs ( 2524 ) Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values specification Governing Specification Conforming to FDDI (FOOTWEAR DESIGN & DEVELOPMENT INSTITUTE

A - 10/A

Sector-24

NOIDA) Specification No. FDDI/SPEC/Jungle Boot/08:2014 (Revised)

approved by MHA vide their letter N o-U.II-98(Spec)/2012-13 -Prov-9775 dated 10/12/2014

and as per following technical requirements * SIZE Size Assorted sizes (5

6

7

8

9

10

11 & 12) as per buyer's requirements Assorted sizes (5

11 & 12) as per buyer's requirements COLOUR Colour Olive Green Olive Green Colour of Sole and Toe Black ( For all other * 1/5 Cap Boots) MATERIALS Upper Material Upper shell consist of Polyester viscose fabric

Water Repellent as an outer layer and 100 % non-woven Nylon (cambrille type) lining as an inner layer. The two fabrics shall be adhered together with flexible adhesive and polyurethane foam of 5 mm thickness. * Blend Composition of polyester viscose fabric water repellent Polyester-80% Viscose- Remainder * Binding material of Polyester blended fabric

black having blend composition of Polyester-67%

Cotton-33% & confirming to IS:15852-2009 for colour fastness to light

washing & pH value YES * Insocks Covered with cambrille type non woven material black * Thermoplastic Toe Puff and Counter Stiffner Thickness when extacted from boot shall be 1.7 mm to 1.9 mm YES * Full Chrome Leather for Toe Cap and Arch piece confirming to IS 5677-1986 for Heat resistance

Colour fastness to rubbing crocking

Solvent extractable substances

water soluble matters

Chromium contents & pH value of water soluble YES * Thickness of Full Chrome Leather for Toe Cap and Arch Piece shall be 1.2 mm to 1.8 mm YES * 2/5 Length of Nylon Laces (cm) 160 * Width of Laces (mm) 6 * Breaking Load of Laces ( 20 cm between grips ) (Test Method- IS: 1969) 750 * Mass per 10 pairs of Laces (g) 125 * Dye Fastness to Washing for Laces shall be above 4 (Test Method- IS/ISO 105-C10: 2006) (Test Condition as per table-2

Test Number- C(3)) YES * Dye Fastness to Light (Test Method- IS: 2454) for Laces shall be above 4. YES * pH Value of aqueous extract shall be 6.5 to 8.5 for Laces YES * Sewing threads Polyester Sewing thread confirming to IS 9543-1980 (Variety No- 7) * OTHER REQUIREMENTS Mass per pair for Size-8 shall be 750 to 850 gms (with increase or decrease of 50 grams for each bigger and smaller size respectively) YES * SOLE Sole Direct Moulded Polyurethane * Minimum thickness of sole (mm) 4 * Cleat height (mm) 2.5 * Thickness of sole when measured at forepart from outside with side wall (mm) 20 * Thickness of sole when measured at waist from outside with side wall (mm) 16 * Thickness of sole when measured at heel from outside with side wall 35 * 3/5 (mm) TEST REPORT Availability of Test Report from NABL ILAC accredited or Central Government Lab to prove conformity of products to the specification. YES YES Name of the Lab CLRI * Address of The Lab ADYAR CEHHNAI * Test Report No. 45/CLRI/2017-2018 * Test Report Date 25-1-2017 * Test reports to be furnished to buyer on demand

if claimed to be available YES * ADVANCE SAMPLE * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Vivek Srivastav 490006

THQ IG SPL OPS

BSP Hr Secondary School

Opposite SBI- Maroda Uttai Risali sector

Bhilai 2524 15