RequiredExperience with Government Bid to RA enabled No Track Suits - Sports ( 300 pieces ) Technical Specifications * As per GeM Category Specification Specification Specification Name Values Bid Requirement (Allowed Values) UTILITY UTILITY Unisex * COMPONENTS Components Complete Set consisting of Upper and Lower * MATERIAL Fabric ( Composition ) Polyester Blended With Viscose Polyester
RequiredMercerised Combed Cotton
RequiredPolyester Blended with Cotton
RequiredPolyester Blended With Viscose Percentage of Polyester 65 % and Polyester 50 % and 1/8 Blending ( in case of Blended Fabric ) Viscose 35 % Cotton 50 %
RequiredPolyester 50 % and Viscose 50 %
RequiredPolyester 65 % and Cotton 35 %
RequiredPolyester 65 % and Viscose 35 %
RequiredNot Applicable Mass ( gram per square mtrs ) 220 * Fabric Construction Knitted Woven
RequiredKnitted Weave ( In case of Woven Fabric ) Plain Plain
RequiredDiamond
RequiredBox Weave
RequiredNot Applicable
RequiredAny other weave as per buyer's requirements Any other weave as per buyer's requirements ( in case weave is other than already mentioned above ) - * Knitting ( In case of knitted Fabric ) Interlock Knitted Plain ( Single Jersey ) Knitted
RequiredInterlock Knitted
RequiredNot Applicable Ends per dm - * Picks per dm - * Courses per dm - * Wales per dm - * Count of knitting yarn - * Raising at inner side of Main Fabric Yes Yes
RequiredNo Upper Lining Yes Yes
RequiredNo Lower Lining Yes Yes
RequiredNo Lining Material 100% Polyester Mesh 100% Polyester Mesh
RequiredNot Applicable Mass of Lining (Gram per Square Meter) Not Applicable * Netting mesh No of holes on base & bias within 625 Square millimeter Not Applicable * Technical Requirements of Slide Fastener for Upper Closing No Medium special duty Open End as per IS 14181 Latest
RequiredLight Duty as per IS 14181 Latest
RequiredNo Technical Requirements of Slide Fastener for Pocket Closing ( For Pockets with Slide No Medium special duty Open End as per IS 14181 Latest
RequiredLight Duty as per IS 14181 Latest
RequiredNo
RequiredNot 2/8 Fastner for closing ) applicable Slide Fastners are BIS Marked Not Applicable Yes
RequiredNo
RequiredNot Applicable Width of Tape Elastic at Waist of Trouser 4.0 cm * Width of Tape Elastic at Bottom of Upper 4.0 cm * Technical Requirements of Waist Band No Waist band as per IS 9686- 1980 latest
RequiredNo Waist Draw Cord Polypropylene Cord of 4mm dia * Draw Cord Ends Fused * Breaking Strength of Draw Cord 340 N minimum * Sleeve Ends ( Cuff ) Elastic Tape * Upper provided with Piping Yes Yes
RequiredNo Lower provided with Piping No Yes
RequiredNo Piping Fabric- Composition 100 percent Polyester * Piping Fabric- Any other material as per buyer's requirements ( Other than mentioned above ) - * Piping Fabric Mass ( gram per square mtrs ) 90 80
Required90
Required110
Required130
RequiredNot Applicable Embroidery Thread Not Applicable Polyester
RequiredRayon
RequiredMercerised Cotton
RequiredSilk
RequiredNot Applicable SIZE Size Extra Large (XL) Small (S)
RequiredMedium (M)
RequiredLarge (L)
RequiredExtra Large (XL)
RequiredDouble Extra Large (XXL) DIMENSIONS OF UPPER Width Across Chest 25 mm below under arm 57.5 cm ( Extra Large ) * Width Across Bottom Opening (relaxed) 50 cm ( Extra Large ) * Length at front from top of collar to bottom 70 cm ( Extra Large ) * Sleeve length (from center of back to bottom of sleeve 89.5 cm ( Extra Large ) * 3/8 Sleeve opening relaxed ( Cuff ) Width 9 * Front Neck Drop 9 * Back Neck Drop 2 * Length of Slide Fastener 68 cm ( Extra Large ) * DIMENSIONS OF LOWER Side Seam Length 109.5 cm ( Extra Large ) * Waist relaxed ( Width Across ) 47 cm ( Extra Large ) * Waist stretched (Width Across ) 57.5 cm ( Extra Large ) * Seat/Hip ( 15 cm below waist band) 57.5 cm ( Extra Large ) * Thigh (at Crotch) ( Width Across ) 38 cm ( Extra Large ) * Bottom Opening ( Width Across ) 25 * Front rise including waist band 30 cm ( Extra Large ) * Back rise including waist band 40 cm ( Extra Large ) * Length of Waist Tying Cord 154 * Bottom Fold (Hem) with full turn in(cm) 2.5 * POCKETS Number of Pockets (Upper) 2 Side Pockets 2 Side Pockets
Required2 Side Pockets and one Inside Pocket at Chest
RequiredWithout Pockets Size of Side Pockets- Upper ( Length X Width ) ( cm ) 18 X 20 cm * Size of Inside Pocket at Chest- Upper Not Applicable * Side Pocket opening - Upper 15.0 cm * Side Pocket Closure with Slide Fastener -Upper No Yes
RequiredNo
RequiredNot Applicable Number of Pockets (Lower) 2 Side Pockets 2 Side Pockets
Required2 Side Pockets and 1 Back Pocket
RequiredWithout Pockets Size of Side Pockets - Lower ( Length X Width 18 cm X 20 cm * 4/8 ) ( cm ) Side Pocket Opening- Lower 15 * Pocket Closure with Slide Fastener - Lower All Pockets with Slide Fastener Side Pockets with Slide Fastener
RequiredBack Pockets with Slide Fastener
RequiredAll Pockets with Slide Fastener
RequiredAll Pockets without Slide Fastener Material of Pockets Main Basic Fabric * COLLAR Collar Type Stand and Fall Type
RequiredMade of two layers of self material * Collar Reinforcement Without Reinforcement * SLEEVE Sleeve Type Reglan Sleeve * PIPING Position and Dimensions of Piping on Upper - * Position and Dimensions of Piping on Lower - * STITCHING Sewing Thread 125 d tex X 3
RequiredPolyester * Raw edges
Requiredif any shall be bound by overlock stitching Yes * Waist band stitching of Upper Stitched in three rows with chain stitch on the elastic * Sleeve Bottom (Cuff ) Stitching Stitched in three rows with chain stitch on the elastic * Waist band stitching of Lower Stitched in three rows with chain stitch on the elastic * Lining seams Inverted * Bartack Stitching ( Reinforcement Stitching ) at stress bearing areas Pocket opening
RequiredCentre of Waist Band Seam and bottom hem and other stress bearing areas * Tunnel at Waist Band for Lower Two holes stitched to allow the draw cord with insertion free movement * Stitches per dm ( min ) 36 * COLOUR/PRINT Colour Light Blue * 5/8 Multicolour Contrasting Pannels Any other colour as per buyer's requirements - * Sublimation Printing (for 100 % polyester only) Sublimation Print as per buyer's requirements Sublimation Print as per buyer's requirements
RequiredWithout
RequiredNot applicable Sublimation Print as per buyer's requirements - * Colourfastness to Light ( IS 2454 ) 5 * Colourfastness to Washing ( IS/ISO 105-C10
RequiredTest- C (3)) Change in Colour- 4; Staining of Adjacent Fabric- 3-4 * Colourfastness to Rubbing ( IS 766 ) Dry- 4/Wet- 3 * Colourfastness to perspiration ( IS 971 ) 4 * Colour of Mesh Lining Same as colour of the base fabric White
RequiredSame as colour of the base fabric
RequiredAny other colour as per buyer's requirements
RequiredNot Applicable Any other colour of Mesh Lining as per buyer's requirements - * Colourfastness to Washing ( IS/ISO 105-C10
RequiredTest- C (3))- Mesh Lining Not Applicable * Colourfastness to perspiration ( IS 971 )- Mesh Lining Not Applicable * Colour of Piping Material Blue * Any other colour as per buyer's requirements - * OTHER REQUIREMENTS Pilling Resistant [after 5 hours Test as per IS 10971 (Part 1)]
Requiredmin 4 * Dimensional stability to washing
RequiredShrinkage or Elongation Percentage
Requiredmax ( IS 2977 latest)
Requiredin lengthwise and widthwise direction 3 1
Required2
Required3 6/8 LOGO AND MARKING Logo/Totem Marking As per buyer's requirements As per buyer's requirements
RequiredNo Type of Logo Printed Embroidery
RequiredPrinted
RequiredEmbossed
RequiredNot Applicable Number of Logos on Upper Not Applicable 1
Required2
Required3
RequiredNot Applicable Number of Logos on Lower Not Applicable 1
Required2
Required3
RequiredNot Applicable Size
RequiredDesign and Location of Logo as per buyer's requirement - * TEST REPORT Availability of Test Report from designated AHSP NABL/ILAC accredited or Central Government Lab to prove conformity of products to the specification No Yes
RequiredNo Test Report No - * Test Report Date - * Name of the Lab - * Address of the Lab - * Test reports to be furnished to buyer on demand
Requiredif claimed to be available Not applicable * ADVANCE SAMPLE Agree to provide Advance Sample(s) for buyer's approval before commencement of supply Yes Yes
RequiredNo
RequiredNot applicable * Specifications highlighted in bold are the Golden Parameters. * Bidders may note that In respect of non-golden Parameters
Requiredthe specifications 'Values' chosen by Buyer will generally be preferred over 'Bid requirement ( allowed Values) by the Buyer.
