Spl repair to certain Bldg and provn of gate, boundary wall, toilet, laundry area for women at Old Cantt Allahabad.

Amount

Dismantling of 6 mm thick AC corrugated or non- corrugated sheets in roof covering including ridges, hips, valleys and flashings etc , complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 MPa as in roof covering / cladding to wall, fixed with self tapping screws, fixed in repair, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 MPa as in roof covering / cladding to wall, valley gutter, ridge hips etc, fixed with self tapping screws, fixed in repair, complete all as specified and directed.

Dismantling timber scantlings, as in framed work, 40sq. cm and over in section, in any position, complete all as specified and directed.

Mild steel work in tubular trusses, purlins, rafter, vertical posts including special shaped washer, angle cleats, fish plates, gusset plates, base/ bearing plates, bolts and nuts etc. complete using ERW or induction butt welded tubes conforming to 1161-1979 grade st 240, complete all as specified and directed.

Mild steel flat iron wind ties for roof including all necessary drilling, bolting or riveting etc complete all as specified and as directed.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets, complete all as specified and directed.

Anodised aluminium snap grid frame work of size 605 x 605 mm for false ceiling with hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long, complete all as specified and directed.

Non asbestos fibre cement building boards, 4mm thick, fixed or laid/ inserted to timber/GI/Aluminium framework with screws, complete all as speciifed and directed.

Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed.

Brickwork in half brick thick walls with fly ash bricks, staright or curved on plan to any radius, built in CM 1:4, complete all as specified and directed.

Brickwork with fly ash bricks, straight or curved on plan exceeding 6metre mean radius, built in CM 1:6, complete all as specified and directed.

Brickwork with sub class B old size fly ash bricks, straight or curved on plan exceeding 6metre mean radius, built in CM 1:4, complete all as specified and directed.

Taking down cement plaster on brick or stone walls or wall tiles etc including raking out joints, hacking for key, scrubbing down with water etc including removal of rubbish off the premises, complete all as specified and directed.

Rendering 15mm thick, on other than fair faces of brick work or concrete surfaces in cement mortar 1:6, finished surface even and fair, complete all as specified and directed.

Rendering 15mm thick in CM 1:4, mixed with water proofing compound, on fair faces of brick work or concrete surfaces of walls, finishing the surface even and fair, complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

Supply only liquid water proofing compound of approved make, complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying two coats of cement base paint of approved colour over a coat of primer, complete all as specifed and directed.

Preparation of new plastered surfaces of walls and applying two coats of acrylic emulsion paint of approved colour over a coat of primer over 1mm thick wall care putty finish, complete all as specifed and directed.

Demolition of Concrete work (un-reinforced) in ground floors and pavings including floor tiles not exeeding 15 cm thickness (below or above ground level) and removal of debris from the site, complete all as specified and directed.

PCC (1:3:6) type C-1 using 20mm graded stone aggregate, 75 mm thick, as in plinth protection laid in bays complete including finishing the surface even and smooth without using extra cement, complete all as specified and directed.

PCC (1:3:6) type C-2 using 40mm graded stone aggregate, 75 mm thick, as in sub base to floor finish, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

Non - skid Ceramic, coloured tiles 7 to 8 mm thick, size of each tile shall be 600mm x 600mm, as in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, laid over and including provision of 15 mm thick screed bed in CM 1:4, complete all as specified and directed.

Non - skid Ceramic, coloured tiles 7 to 8 mm thick, size of each tile shall be 600mm x 600mm, as in vertical surfaces such as skirting / dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, laid over and including provision of 10 mm thick backing coat in CM 1:3, complete all as specified and directed.

Glazed ceramic coloured tiles as in vertical surface of walls such as skirting / dado and risers to steps, size of tile shall be 450 mm x 350 mm x 7 mm thick, set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match the colour or shade of tiles, laid over and including provison of 10 mm thick rendering as in backing coat of tiles in cement mortar 1:3, complete all as specified and directed.

Non - skid Ceramic, coloured tiles 7 to 8 mm thick, size of each tile shall be 400mm x 400mm, as in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, laid over and including provision of 15 mm thick screed bed in CM 1:4, complete all as specified and directed.

Providing damp-proof layer in two coats of acrylic polymer coating consisting of 1 part acrylic polymer mixed with 2 parts of cementitious powder applied at the rate of 1.4 sqm/kg of mix per coat, complete all as speciifed and directed. Note: (a) Second coat to be applied after 4-6 hours of first coat. (b) 5 days curing to be carried out to the surface before plastering. Make: 'Smart Care damp block 2K' of Asian Paints or equivalent of Dr Fixit, STP, CICA

Taking down chowkats or frames exceeding 1.5sq.m but not exceeding 4sq.m each with shutters (without taking off shutters from the frames) including removing from site, complete all as specified and directed.

Taking down chowkats or frames not exceeding 1.5sq.m each with shutters (without taking off shutters from the frames) including removing from site, complete all as specified and directed.

Factory made uPVC white colour Sliding window Three track of area not exc 2.00 Sqm each made of extruded profiles with wall thickness of 2.3mm (+/- 0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2(+/- 0.2)mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories., complete all as specified an directed. Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.

Framed work such as grills, gratings, etc.. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, and similar work conforming to Fe-290 Gde-E-165, complete all as specified and directed.

Preparation of new steel and iron surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Preparation of new steel and iron surfaces over 10cm width or girth and applying two coats of synthetic enamel paint , complete all as specified and directed.

Sheet glass, tinted, 5.5 mm thick, ordinary quality and glazing in squares not exceeding 0.5 sq. m in each pane with oil putty, complete all as specified and directed.

Sheet glass, frosted, 5.5mm thick, ordinary quality and glazing in squares not exceeding 0.5 sq. m in each pane with oil putty, complete all as specified and directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet PVC sheet reinforced with M.S. square tube, supplying & fixing in opening as per specification & drawing complete all as specified.

Factory Made Solid PVC Moulded Door Shutter with particle board core 28 to 30 mm thick (stiles), with 2, 4, or 6 raised panel design with 2 mm thick Moulded PVC Sheet on the front face & 2 mm plain colour PVC sheet on back face, with Particle board core, supplying & fixing in the frame at site as per specification & sketch shown in section 8 of SSR part II, complete all as specified and directed.

Stainless steel handles, fabricated type, 150mm long, complete all as specified and directed.

Stainless steel, barrel tower bolts of extruded section and fixed, 150mm long, complete all as specified and directed.

Butt hinges, medium weight, stainless steel, and fixed, 100mm size, complete all as specified and directed.

Plain cement concrete, 100 mm thick, 1:4:8, type D-2 (using 40 mm graded stone aggregate) for sub base of floor & filling up sunken floor over felt, complete all as specified and directed.

Sand filling under floors or in foundations including watering and consolidation, complete all as specified and directed.

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, complete all as specified and directed.

PCC type-B-1, 1:2:4 using 20mm graded stone aggregate as in Bed blocks, copings, path etc including necessary formwork, complete all as specified and directed.

Stainless steel curtain rod of 304 grade, 25 mm dia, for door and windows including one pair of SS bracket and steel cover for each rod cut to size and fixed in position, fixed in repair, complete all as specified and directed.

Vitreous China wash basin, white, flat back, size 630 x 450mm including brackets, waste coupling, fixed in repair, complete all as specified and as directed.

Vitreous China wash basin, white, flat back, size 550 x 400mm, excluding taps, waste chain and plug but including brackets, waste coupling, complete all as specified and as directed.

PVC Waste pipe, 32mm dia, of 750 mm length complete including fixing to waste coupling and to the grating, fixed in repair, complete all as specified and directed.

PVC connection 15mm size with PTMT nuts on both ends of length 600mm, complete all as specified and directed..

Angle valve, cast copper alloy, fancy type, screwed down, high pressure, with crutch or butterfly handle, with long shank and cup (angle type), screwed both ends for iron pipe or for unions and fixed 15mm bore, fixed in repairs, complete all as specified and directed. Make: Cera QT F2006202 or any other commercially equivalent make as approved by GE.

PVC (SWR) floor trap with CP grating, plain jointing with solvent cement, 75mm bore, complete all as specified and directed.

Pillar taps, cast copper alloy, capstan head type, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shank and fly-nuts, screwed for iron pipe 15mm bore, fancy type, fixed in repair, complete all as specified and directed.

Aluminium anodised tubular towel rail, 20mm dia including brackets fixed to wall, fixed in repair, complete all as specified and directed.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed with screws, fixed in repair, comnplete all as specified and directed.

Stainless steel soap dish fixed to walls, complete all as specified and directed. Make: CERA F5007106 or any other commercially equivalent make as approved by GE.

Towel ring of PTMT fixed with and including Chromium plated brass screws and wooden / plastic cleats( Min Wt 90 gms), fixed in repair, complete all as specified and directed.

Stop valves, cast copper alloy, screwed down, high pressure, with capstan headed handle, with long shank and cup screwed both ends for iron pipe or for unions and fixed but fancy type, chromium plated (concealed type), 15 mm bore, fixed in repair, complete all as specified and directed.

Chromium plated brass shower rose 125 mm long, fancy type with swivel joints fixed to 15mm bore pipe, fixed in repair, complete all as specified and directed.

Bib taps, cast copper alloy, chromium plated, long body fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule for 15mm bore, complete all as specified and directed.

Water closet squatting pan 'Orissa Pattern' of size 580 x 440 mm white with integral foot rest (excluding flushing cistern and flush pipe) with P' or 'S' trap complete incl connection to trap and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor, fixed in repair, complete all as specified and directed.

PVC low level cistern, 10 litre capacity, white’ with inlet, float valve including bracket with 32mm dia PVC pipe 600 mm long, fixed in repair, complete all as specified and directed.

Vitreous china wash down water closet pedetal pan white, including 10 ltrs PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, flush pipe of polythylene of low or high density or PVC 32mm dia, including plastic water closet seat, closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminium hinging device, fixed in repair, complete all as specified and as directed.

Bib cock, 2 way, with wall flange 15 mm dia including fixing to pipe, fixed in repair, complete all as specified and as directed. Make:CERA Cat No. F1002161 or any other commercially equivalent make as approved by GE.

Hand shower (health faucet) ABS body with 8 mm dia 1.2 m long flexible tube and wall hook including fixing complete all as specified and as directed. Make:CERA Cat No.F8030107AB or any other commercially equivalent make as approved by GE.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed wate tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified and directed.

Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), WHITE colour, 500 litre capacity, hoisted and fixed in position including necessary fittings such as connection pieces with GI nipple for inlet / outlet & wash out pipes, including ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density PVC float valve 20 mm dia screwed for iron pipe complete as specified in SSR Part-I, fixed in repair, complete as specified & directed.

Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, 20mm bore, fixed in repair, complete all as specified and directed.

Taking up or down galvanised steel tubing 15mm bore and connections, complete all as specified and directed.

Galvanised Steel water tubes medium grade in any size or length galvanised with all fittings and fixed complete to walls and ceiling or laid in floors, bore of pipe 15mm dia, complete all as specified and directed.

Taking up or down galvanised steel tubing 20mm bore and connections, complete all as specified and directed.

Galvanised Steel water tubes medium grade in any size or length galvanised with all fittings and fixed complete to walls and ceiling or laid in floors, bore of pipe 20mm dia, complete all as specified and directed.

Excavation in trenches not exceeding 1.5m deep and not exceeding 1.5m wide or area not exceeding 10 sq.m on plan and depth not exceeding 1.5 m for foundation, for shafts, wells, cesspits, manholes, pier holes etc., and getting out in any type of soil, complete all as specified and directed.

Returning, filling in soils, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick, complete all as specified and directed.

Removing of surplus excavated material to a distance n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point, complete all as specified and directed.

Taking down eaves gutter and rainwater pipes (any size and pattern), including all fittings, head shoes bends swan-necks, etc, incl cleaning for refixing or removal to store complete as specified & directed.

PVC (SWR) 75 mm bore pipes single socketed ends, in any length with rubber ring joints, laid in floors or trenches including earth work, complete all as specified and directed..

PVC (SWR) 110 mm bore pipes single socketed ends, in any length with rubber ring joints, laid in floors or trenches including earth work, complete all as specified and directed..

PVC (SWR) bends of any radius and 75mm bore with oval & accessed door, jointed with adhesive, complete all as specified and directed..

PVC (SWR) bends of any radius and 110mm bore with oval & accessed door, jointed with adhesive, complete all as specified and directed..

PVC (SWR) junction single, (Single T) equal or unequal, 75 mm bore, with oval and accessed door jointed with adhesive, complete all as specified and directed..

PVC (SWR) junction single, (Single T) equal or unequal, 110 mm bore, with oval and accessed door jointed with adhesive, complete all as specified and directed..

PVC (SWR) vent cowl, 110mm size, complete all as specified and directed..

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Plain cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregate), as in mass concrete in foundation filling, complete all as specified and directed.

Plain cement concrete type C-2, 1:3:6 (using 40mm graded stone aggregate), as in mass concrete in foundation filling, complete all as specified and directed.

Hardcore, of broken stone or boulders, of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

Plain cement concrete 1:2:4 type B-1 (20mm graded stone aggregate), 25mm thick, as in levelling course, complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc, complete all as specified and directed.

Formwork to flat rough finished surface of soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, complete all as specified and directed.

RCC M-25 (design mix) using 20mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed. Note: Reinforcement shall be measured and paid separately.

TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

TMT bars 5mm dia and over upto 10mm dia, in spacers, binders and stirrups, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Sand stone slabs of thickness 10 cm in sun-shades, chajjas, shelves, cills, landings, cover stones, templates, etc. n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4. complete all as specified and directed.

Pressed steel frames for doors of size 105mm x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed, complete all as specified and directed.

Pressed steel frames for doors of size 125mm x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed, complete all as specified and directed.

Flush shutters 35 mm thick, factory made, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.

Glazed and skeleton shutters, 35mm thick, second class hardwood, open rebated and prepared to receive glass, gauze, etc. (without sash bars), divided into squares with plain, chamfered or rounded mitered beads for securing glass/gauge complete all as specified in SSR Pt- I, section 8, clause 8.24(a) and as directed. Note: Glass or wire cloth, etc. in panels or sash squares shall be measured and paid separately.

Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specifed and direcetd.

Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, fixed in repairs, complete all as specifed and direcetd.

Sheet glass, 4 mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, fixed in repair, complete as specified & directed.

Frosted sheet glass, 4 mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, complete as specified & directed.

Frosted sheet glass, 4 mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, fixed in repair, complete as specified & directed.

Preparation of new wooden surfaces exc 10 cm width or girth with sand or emery paper & applying two coats of synthetic enamel paint over a coat of pink primer , complete all as specified and directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as specified and directed. MAKE:- Sintex / Rajshree plastic / Wood Forex, Indore

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification, complete all as specified and directed. MAKE:- Sintex / Rajshree plastic / Wood Forex, Indore / M/s Kumar Arch Tech Ltd.

Butt hinges, medium weight, cold rolled mild steel, and fixed, 100mm size, complete all as specified and directed.

Aluminium alloy handles, cast type, anodised, 150mm long, complete all as specified and directed.

Aluminium anodised, barrel tower bolts of extruded section and fixed, 200mm long, complete all as specified and directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed 250mm long, complete all as specified and directed.

Rendering 5mm thick, on cement concrete surfaces in ceiling in cement sand mortar 1:3, finished surface even and fair without using extra cement, complete all as specified and directed.

Preparation of new plastered surfaces and applying two coats of white wash on ceiling, complete all as specified and directed.

Complete removal of existing treatment from walls (any number of layers) by scrapping with steel scrappers or any other means, filling depressions of scrapped surfaces with wall care putty and applying uniform layer of 1mm thick wall care putty (Make: JK white or Birla) including preparation of surfaces by rubbing with appropriate size of sand or emery paper and applying two coats of acrylic emulsion paint on walls surface, complete all as specified and directed.

Angle cock, 15mm bore, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipes, complete all as specified and directed.

Low density ployethene (LDPE) pipes of pressure rating 6 kgf/sqcm, 32mm bore, complete all as specified and directed.

Tubular towel rail brass chromium plated, 20mm dia, 'D' type, 600mm long between flanges, including brackets fixed to wall, complete all as specified and directed.

RCC 1:1.5:3 type A-1 (nominal mix) using 20mm graded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and directed. Note: Reinforcement shall be measured and paid separately.

RCC 1:1.5:3 type A-1 (nominal mix) using 20mm graded stone aggregate as in columns, pillars, piers, posts and struts, complete all as specified and directed. Note: Reinforcement shall be measured and paid separately.

Formwork to rough finished sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, complete all as specified and directed.

Formwork to rough finished square, rectangular, polygonal surface of concrete in sides of pillars, posts, struts, piers, columns and stanchions, complete all as speciifed and directed.

Granite, 12mm thick, (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed.

Mild steel, 1.25mm thick, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required, complete all as specified and directed.

Rolled mild steel conforming to Fe 410-W(Gde-E- 250) quality-A, in work as in posts, struts, rafter, purlins, doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, complete all as specified and directed.

Excavation in post holes or similar holes in loose/soft soil each not exceeding 0.5 cum, getting out, returning filling in and ramming earth in layers note exceeding 25cm well watering and removing surplus soil to a distance not exceeding 50m and making good surface where ever required, complete all as specified and directed.

Concrete bed to 100 mm bore drain pipes including packing under and haunching against the sides of pipes, in PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate), complete all as specified and directed.

Supply, laying, jointing and testing of Salt-glazed stoneware drain pipes of grade 'A', internal diameter 100 mm, laid in trenches and jointed with bends and taper bends, any radius complete with collars CM 1:1, complete all as specified and directed. NOTE:- The measurements shall be net as fixed between the fittings without any allowances for cutting and waste. Quoted rate shall deemed to include all necessary extra joints, waste and cutting.

PCC 1:2:4 type B-0 using 12.5mm crushed stone aggregate as in surface channels and drains including necessary form work if required complete all as specified and directed..

Precast reinforced cement concrete as in cover slabs (for manholes) chullah hoods, chajjas, water trough, mangers, shelves and other similar works, type A-1, 1:1.5:3 using 20 mm graded agg. set in cement mortar 1:4, complete all as specified and directed. Note: Reinforcement to be measured and paid separately.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc, complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required, complete all as specified and directed.

Taking down carefully point wiring of any type and any description / caping or concealed [light point, fan point or socket point] including removal of battens, pipes, plug sockets, switches, shades, ceiling roses, light fittings etc complete and making good disturbed surface to match the exisitng, complete all as specified and directed.

Taking down main switches, distribution boards and cut outs of any capacity along with the exisitng boards and removing the same from site and making good disturbed surface or portion of walls complete all as specified & directed.

Taking down carefully sub main wiring of any numbers of wire on wooden batten or surface conduit or concealed conduits / casing caping any type complete all as specified & directed.

Point wiring complete with PVC insulated unsheatehd, 1100 volts grade cable 1.5 sq.mm (nominal area) FR type multi stranded copper conductor, single core drawn in and including not less than 20mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories, including provision of concealed pressed steel terminal box of required size not less than 1.6 mm thick factory made duly painted inside and outside with two coats of black bituminous paint over and including a coat of red oxide primer, with 3.0 mm thick top cover of plastic laminated sheet of required colour for mounting switch, sockets, fan regulator etc, including 1.5 sq.mm FR type PVC insulated unsheathed cable multi stranded copper conductor of green colour as continuous earth wire and connected to earth dolly as required at site and including chases cutting and making good the disturbed surface and applying finishes to match the existing surface, complete all as specified and directed for the following:-

(a) One light / fan / bell / exhaust fan point, controlled by one one-way 5Amp switch

(b) One 5 pin, 5 Amp socket outlet on the same board with other switches

(c) One 5 pin, 5 Amp socket outlet point on an independent board.

Point wiring complete with PVC insulated unsheatehd, 1100 volts grade cable 2.5 sq.mm (nominal area) FR type multi stranded copper conductor, single core drawn in and including not less than 20mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring for socket outlet, 6 pin, 15 Amps including provision of concealed opressed steel terminal box of required size not less than 1.6 mm thick factory made duly painted inside and outside with two coats of black bituminous paint over and including a coat of red oxide primer, with 3.0 mm thick top cover of plastic lmainated sheet of required colour for mounting switch, sockets, fan regulator etc, including 2.5 sq.mm FR type PVC insulated unsheathed cable multi stranded copper conductor of green colour as continuous earth wire and connected to earth dolly as required at site and including chases cutting and making good the disturbed surface and applying finishes to match the existing surface, complete all as specified and directed.

Switch piano, flush type single pole, one way 5/6 Amp 240 volts, white or ivory, ISI marked, complete all as specified and directed.

Socket outlet, 2 in 1, 5 pin, 5/6 Amps 240 Volts, flush type, fixed in repairs, complete all as specified and directed.

Switch piano, single pole, one way 15 Amp 240 volts, ISI marked, complete all as specified and directed.

Socket outlet, 2 in 1, 6 pin, 15 Amps 240 Volts, flush type, fixed in repairs, complete all as specified and directed.

Ceiling rose, single phase, PVC / polycarbonate, insulated body, three terminals, surface bakelite sheet 63.5mm dia, fixed in repairs, complete all as specified and directed.

Stepped type electronic fan regulator flush type duly fixed on the existing phenolic laminated sheet etc. as required, 240V, humming free, 2 module, ISI marked, fixed in repairs complete all as specified and directed.

Lamp holder, PVC/polycarbonate body with back plate/ cord grip cap suitable for batten/ angle/ pendent fittings, fixed in repairs complete all as specified and directed.

Sheet metal enclosure for MCB DBs SPN, 8 way, double door, vertical type, 240 V with 200 Amps rated bus bar, complete with incoming/ outgoing connection through proper size of lugs and cable glands including taking down existing MCB DBs, complete all as specified and directed.

Sheet metal enclosure for MCB DBs TPN, 4 way, double door, vertical type, 415 V with 200 Amps rated bus bar, complete with incoming/ outgoing connection through proper size of lugs and cable glands including taking down existing MCB DBs, complete all as specified and directed.

MCB, TPN, 63 Amps, 415 V, conforming to 'C' curve, 10kA breaking capacity, complete all as specified and directed.

MCB, SPN, 6 to 32 Amp, 240 Volt, conforming to 'C' curve, 10kA breaking capacity, complete all as specified and directed.

MCB, SP, 6 to 32 Amp, 240 Volt, conforming to 'C' curve, 10kA breaking capacity, complete all as specified and directed.

LED bulk head light fittings 1x10 watt having 600 Lumen enclosed in polycarbonate body, weather proof with co-extruded poly carbonate body, envoirement friendly, energy efficient pre-wired and making necessary electric connection from ceiling rose with flexible copper wire or fixed to wall firmly, fixed in repairs, complete all as specified & directed. Make : Havell's Cat Part No. HEXAFT10WLED857SSYMBOPC / Bajaj Model Wee Plus Cat Part No. BIBWP10LED or techno-commercially equivalent model in Crompton or Philips as approved by GE.

LED wall mounted tube light fitting, 1x18W, LED 6000K, decorative ultra slim linear LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient complete with all accessories, pre-wired and making connection with and including provision of three core flexible copper cable of size 23/0.0076 from ceiling rose to connector of required length including LED lamp, complete all as specified and directed. Make : Havell's Cat Part No. LHEXBHP7INW018 or techno-commercially equivalent model in Crompton or Philips as approved by GE.

LED smartbright spot light fitting, 1x14W, LED 100 lm/W, aluminium housing 5000K, LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient complete with all accessories, pre-wired and making connection with and including provision of three core flexible copper cable of size 23/0.0076 from ceiling rose to connector of required length including LED lamp, complete all as specified and directed. Make: Philips model No ST271T LED 20/840 PSU-EMBIC WH or techno-commercially equivalent model in Crompton/ Havells as approved by GE.

Recess mounted decorative CRCA LED light fittings of size 600 mm x 600 mm, 36 Watt LED 6500 K lumen efficiency, high brightness SMD leds, including suitable driver poly carbonate body, envoirement friendly, energy efficient pre-wired and making necessary electric connection from ceiling rose with flexible copper wire, complete all as specified & directed. Make : Crompton Arion III Cat Part No LCTLSN-36-CDI or techno-commercially equivalent model in Philips/ Havells/ Bajaj as approved by GE.

LED mirror light fitting, 1x9W, 6000K decorative indirect up-down light fitting for mirror and wall light application with extruded polycarbonate environmental friendly energy efficient complete with all accessories, pre-wired and making connection with and including provision of three core flexible copper cable of size 23/0.0076 from ceiling rose to connector of required length including LED lamp, complete all as specified and directed. MAKE:- Cat No. IVORY Model No. LHESABP7IN1W009 of Havells or techno-commercially equivalent model in Philips / Crompton

Building security lighting luminaire 36W with unique peanut optics to ensure uniform distribution, hgiher spacing between poles and maintenance free system for city roads and streets, 50% energy saving, IP 66 protection PC and FG cover, high impact resistance complete including LED lamps and all accessories including bracket made out of 25mm bore light grade GI tubing of 1.20metre length bent to shape required and fixed to existing pole or building by means of two Nos MS FI 40mmx6mm clamps with suitable size bolt, nuts and washers and making connection with and including provision of three core flexible copper cable of size 23/0.0076 from fittinge to existing junction boxr of required length, complete all as specified and directed. MAKE:- Cat No. BRP409 LED CW 036 MR FG S1 PSU GR of Philips or Cat No ENDURACITYLITEPLATPLUSSL36WLED757SASYBOPC of Havells or techno-commercially equivalent model in Bajaj / Crompton

Earthing complete with GI earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground vertically to a depth of not less than 2.25m deep below ground level with the top edge of earth plate at a depth of not less than 1.5m below ground level connected to GI earth lead of 4mm dia by means of bolts, nuts, washers of galvanised iron or steel, GI earth wire shall be protected by 15mm dia GI pipe 'medium grade', GI wire meshed funnel, alternate layer of charcoal and salt on all side to earth plate upto a thickness of 150mm, filling of black cotton soil in earth pit upto GL and connected to earth plate including necessary excavation & earthwork, PCC (1:2:4) type B-1 earth chamber and mild steel angle iron frame 25 x 25 x 6 mm and 40mm thick pre-cast RCC cover (1:2:4), type B-1 (using 20mm graded crushed aggregate) mix with 6mm dia MS bars @75mm c/c both ways, mild steel handle 12mm dia, PGI funnel and wire mesh, 20mm dia GI pipe light grade(ISI marked) for watering, etc complete all as shown in electrical plate No.5 of SSR Part-1, connected to earthing test point, including testing on completion, complete all as speciifed and as directed. NOTE:- The quoted rates shall also deemed to include the cost of Earth Test point and earth wire and protection pipe upto 7.5 metre beyond the earth plates electrode.

Sub main wiring complete with 2 runs of 6 sq.mm PVC insulated and unsheathed 1100V grade multistranded FRLS grade copper conductor cable drawn through and including provision of PVC rigid conduit 20mm dia and accessories connecting terminal ends to DB's including providing 1 run of 6 sq.mm PVC insulated unsheathed multistranded FRLS grade copper cable as earth continuity conductor and connecting to common earth dolly including taking down existing sub main wiring any type and making good disturbed surfaces to match with existing including sinking of boxes , complete all as specified and directed. NOTE:- (i) Two runs of 6 sq.mm copper conductor, one run of 6 sq.mm copper earth continuity conductor and one run of PVC rigid conduit and with accessories shall be measured as one unit length. (ii) Extra length of cable / wire required for connection to MCBs shall not be measured and the rate quoted per unit shall deemed to be inclusive of the same accordingly.

Sub main wiring complete with 2 runs of 4 sq.mm PVC insulated and unsheathed 1100V grade multistranded FRLS grade copper conductor cable drawn through and including provision of PVC rigid conduit 20mm dia and accessories connecting terminal ends to DB's including providing 1 run of 4 sq.mm PVC insulated unsheathed multistranded FRLS grade copper cable as earth continuity conductor and connecting to common earth dolly including taking down existing sub main wiring any type and making good disturbed surfaces to match with existing including sinking of boxes , complete all as specified and directed. NOTE:- (i) Two runs of 4 sq.mm copper conductor, one run of 4 sq.mm copper earth continuity conductor and one run of PVC rigid conduit and with accessories shall be measured as one unit length. (ii) Extra length of cable / wire required for connection to MCBs shall not be measured and the rate quoted per unit shall deemed to be inclusive of the same accordingly.

Taking down / out existing ceiling fan/ exhaust fan for servicing, greasing, replacement of bearing, safety pin, canopy, fan condensor, clamp, rubber reel, nut / bolts as required at site and cleaning and preparing surface, filling cavities with filler including one coat painting with synthetic enamel paint including down rod of approved white colour including marking MES number and refixing in its original position and making all electric connection, complete all as specified and directed..

Taking down / out existing geyser by disconnecting all electric connection and cleaning and preparing surface, filling cavities with filler including one coat painting with synthetic enamel paint of approved white colour including marking MES number and refixing in its original position and making all electric connection, complete all as specified and directed.

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20Amp 240V, fixed in repair, complete all as specified and directed.

Exhaust fan, steel body AC single Phase. 230V of size 380m sweep with, blades, and frame and louvers, including making hole in wall, complete all as specified and directed.

KRISHNA BAHADUR

AMARDEEP ENTERPRISES