REPAIR MAINT OF TILING IN TOILET KITCHEN AND BATHROOM IN MD ACCN OF AGE BR II UNDER GE (EAST) LUCKNOW

Amount

Demolition of PCC as in ground floors & pavings not exc. 15 cm thickness (below or above G.L.) complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4, type B-1 using 20mm graded crushed stone aggregae as in floors, finished even and smooth using extra cement complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified and directed. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

Demolition of brick work built in cement mortar including all of quoins, arches, pillers etc.but excluding ashlar facings and precast concrete articles complete all as specified and directed.

M & L for brick work using fly ash old size bricks straight or curved on plan, exc 6.0 m mean radius, built in CM (1:6) complete, all as specified and directed.

M & L for brick work using fly ash old size bricks, straight or curved on plan to any radius in half brick thick walls in CM 1:4, complete, all as specified and directed.

Taking down cement or cement lime plaster on brick walls etc including raking out joints, hacking for key scrubing down with water etc including terrazzo tile, ceramic tile whereever if required all as specified and directed .

M&L for rendering 10 mm thick in cement mortar 1:6 on fair face of brick work of walls, finished even & smooth without using extra cement, complete, all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on fair face of brick work of walls, mixed with water proofing compound (ISI marked) @ 3% by weight of cement or as per manufacturer’s instructions, finished even & smooth without using extra cement complete, all as specified and directed. Note :- WPC shall be measured and paid separately as "Supply only".

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete, all as specified and directed.

Supply only liquid water proofing compound ISI marked complete, all as specified and directed.

M&L for preparation of new or previously undercoated surface of wall and applying three coats of white wash on wall, complete, all as specified and directed.

M&L for Preparation of new or previously undercoated surface of wall and applying three coats of white wash on ceiling, complete, all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer complete, all as specified and directed.

Complete removal of existing treatment from wall applying two coats of oil bond distemper over a coats of wall care putty (2 mm thick) to make surface even and smooth complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of cement based paint over one coat of primer complete all as specified and directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area exc 1.5 sqm but not exc 4 sqm each, complete, all as specified & directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area not exc 1.5 sqm each, complete all as specified & directed.

Taking down shutters of any description exc 1.0 sqm but not exc 2.0 sqm each complete all as specified & directed.

Taking down shutter of any description exc 1 Sqm and not exc 2 Sqm each and refixing in same opening including easing and adjusting of shutter as required including renewal of unserviceable screws complete all as specified & directed.

S&F 2nd class hard wood (sal) plain, solid, straight chawkhats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified & directed.

S&F 125x60mm size of pressed steel frame for door with one or more rebates including necessary fixing lugs, lock striking plates, hinges, hold fast (40x3mm) etc. complete all as specified & directed.

S&F 105x60mm size of pressed steel frame for door with one or more rebates including necessary fixing lugs, lock striking plates,hinges,hold fast (40x3mm) etc. complete all as specified & directed.

S&F 30mm thick flush shutter solid core construction with block board core and plywood face panels, commercial type on both sides complete, all as specified & directed.

Supply and fixing factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed.

S&F solid PVC door frame of size 50 x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube etc complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting frame made out of MS tube for top and bottom rail MS frame shall be covered with heat mould plain colour PVC C channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for style and plain colour PVC sheet for top rail lock and bottom rail on either side and as gap insert for top rail and bottom rail plain colour PVC sheet tape fixed in MS frame welding sealed to the style and rail with suitable PVC sheet bearing and jointing together with solvent cement etc complete all as specified and directed..

S & F steel windows with side hung shutters including projecting type hinges with steel handles and steel peg stay, complete with glazing bar, dovetailed or welded complete, all as specified and directed.

S & F steel windows with side hung shutters including projecting type hinges with steel handles and steel peg stay, complete without glazing bar, dovetailed or welded complete, all as specified and directed.

S & F steel ventilators with top hung shutters including hinges, steel handle and steel peg stay complete with glazing sash, dovetailed or welded including taking down old window panel, complete, all as specified and directed.

S&F 300 mm long mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia and including minimum of 06 bolts and nuts, four on bolt plate and two on staple plate complete, all as specified & directed.

S&F in repair 300 mm long mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia and including minimum of 06 bolts and nuts, four on bolt plate and two on staple plate complete, all as specified & directed.

S&F 200mm long aluminium anodised barrel tower bolts of extruded section, complete, all as specified & directed.

S&F in repair 200mm long aluminium anodised barrel tower bolts of extruded section, complete, all as specified & directed.

S&F 150 mm size aluminium alloy handles, fabricated type extruded section, ISI marked complete, all as specified & directed.

S&F in repair 150 mm size aluminium alloy handles, fabricated type extruded section, ISI marked complete, all as specified & directed.

S&F stainless steel butt hinges of size 100mm medium weight, steel, ISI marked complete, all as specified & directed.

S&F in repair stainless steel butt hinges of size 100mm medium weight, steel ISI marked complete, all as specified & directed.

Cutting holes in brick work built in cement mortar for inserting hold fast and making good dismantled portion in CM 1:3, depth of cutting exc half brick but n. exc one brick complete, all as specified & directed.

S&F mild steel holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Grade E-165 (Fe 290) including necessary welding etc. and fixed in position complete, all as specified & directed.

S&F mild steel helical door spring 300mm ordinary rat tail rod pattern spring including roller and roller plate complete, all as specified & directed.

S&F in repair 18/19 mm thick prilaminated partical boad, exterior grade, laminated on both side with decorative choice lamination, complete, all as specified & directed.

M&L for in repair block board, 18/19mm thick, grade 1 quality, exterior grade, commercial type, fixed with screws to timber frame work complete, all as specified & directed.

M&L for 0.90mm thick decorative laminates 'Mica type 1 of surface finished,colour and pattern as approved, fixed with adhesive as per makers instructions complete, all as specified & directed.

M & L for 6mm thick external teak wood lipping for block board or veneered particle board , fixed with nails, complete all as specified and directed.

M&L 2nd class hard wood, wooden beading, plain fillets, square or rectangular or tringular in section clean sawn sectional area exc 3 sqcm but not exc 6 Sqcm fixed with nail complete, all as specified & directed.

M&L 2nd class hard wood, plain fillets, square or rectangular or tringular in section clean sawn sectional area n exc 3 sqcm fixed with nail complete, all as specified & directed.

S&F continuous piano hinges, mild steel bright finished or electro galvanized with width of flap 30mm when open complete, all as specified & directed.

S&F for self closing stainless steel hinge, fancy type, bright finished or electro galvanized fixed with SS screws complete all as specified & directed.

S&F magnet catcher for cup board shutter complete all as specified & directed.

M&L for preparation of new or previously untreated surface of wood or wood based materials of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete, all as specified & directed.

Hacking out old broken glass (any thickness, size, quality or description) from iron frames glazed with putty or wooden beads, complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality & glazing with oil putty or wooden beads in square area not exc 0.5 Sqm in each pane, complete, all as specified and directed.

S&F of 4.00 mm thick figured glass, pin head type and glazing with oil putty in squares not exc 0.5 sqm in each pane, all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete, all as specified & directed.

S&F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified.including taking down ms door frame/wooden door frame including wooden beading and refing ms door shutter/wooden door shutter with new wire mesh with tinned tack/flat iron in steel door and wooden beading in wooden door for securing the wire messe and making good the disturbed portion during execution complete, all as specified & directed. (Including welding work appy where as required.)

S&F in repair drapery rods, coloured, standrad quality, PVC coated not less than 25mm dia with heads at both ends and middle support, rings etc. complete, all as specified & directed.

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome, complete, all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete, all as specified & directed.

M&L for Non skid coloured ceramic edge cut tiles 7 to 8 mm thick (square/ rectanglar) area of each tiles exc 0.06 Sqm but not exc 0.11 Sqm as in floor over and including screed bed 15mm thick in CM 1:4 or beding layer for laying floor finishes etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete, all as specified and directed.

M&L for Non skid coloured ceramic edge cut tiles 7 to 8 mm thick (square/ rectanglar) area of each tiles exc 0.18 Sqm but not exc 0.36 Sqm as in floor over and including screed bed 15mm thick in CM 1:4 or beding layer for laying floor finishes etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete, all as specified and directed.

M&L for coloured glazed ceramic edge cut tiles 600x300 x 7 mm thick but as on vertical surfaces such as skirting/dado over and including 10mm thick rendering in CM 1:3 complete, all as specified & directed.

S&F 15 to 18mm thick granite stone slab (any shade) including grinding moulding and polishing as in floor/plate form fixed over and including 15mm thick screed in CM 1:4, complete, all as specified and directed.

Rounding to edges of stone slabs one edge such as in steps, cooking platform and similar situation, complete, all as specified & directed.

S&F for GI tubing medium grade 15mm dia galvanised with all fitting and fixed, complete to walls and ceilings or laid in floors including taking up or down of existing tubing complete, all as specified & directed.

S&F for GI tubing medium grade 20mm dia galvanised with all fitting and fixed, complete to walls and ceilings or laid in floors including taking up or down of existing tubing complete, all as specified & directed.

Cutting chases, pinning in brick walls for concealed water tubing making good to facings where required and pointing in CM 1:3 cutting not exceeding 10 cm girth complete, all as specified & directed.

Cleaning and removing all scale and dirt etc from tank and mouth of circulating pipe and refixing of capacity exc 250 n exc 500 ltrs complete, all as specified & directed.

Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including dismantling of existing tank complete, all as specified & directed.

S&F 20 mm ball valve high pressure of PTMT with apoxy coated aluminium rod and high density plastic ball screwed for iron pipe, complete, all as specified & directed.

S&F in repair 20 mm ball valve high pressure of PTMT with apoxy coated aluminium rod and high density plastic ball screwed for iron pipe, complete, all as specified & directed.

S&F gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20 mm bore complete, all as specified & directed.

S&F in repairs vitreous china wash down water closet pan (Pedestal pattern), white, including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc., with plastic WC seat cover (white) closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device, complete, all as specified & directed.

S&F vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, 'P' or 'S' trap, including connection to trap and flushing pipe, antisyphonage pipe etc including provision of PCC (1:5:10) type E2 in filling, making good to floor, complete, all as specified & directed.

S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete, all as specified & directed.

S&F in repair plastic water closet seat cover black/white, closed pattern with flat bottmom & cover and aluminum anodised hinging device complete, all as specified & directed.

S&F in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete, all as specified & directed.

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed on wall with PVC rawl plug & cadmium plated brass screws, complete all as specified & directed.

S&F in repair long body 15 mm bore bib tap, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified & directed.

S&F in repair CP angle valve for 15 mm bore pipe with capstan head long screwed shank including cp cover plate fancy type fixed as in repair complete, all as specified & directed.

S&F in repair 15mm bore concealed type, stop valve cast copper alloy screwed down high pressure with capstan head and cup, screwed both ends for iron pipe or for union complete, all as specified & directed.

S&F in repairs long body15mm bore fancy type pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes complete, all as specified & directed.

S&F in repairs tubular towel rail, chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete, all as specified & directed.

S&F PVC connection of 15mm bore, 600mm long with brass coupling on both ends of superior quality complete, all as specified & directed.

S&F 20 mm thick granite stone slab (any shade) including grinding moulding and polishing as in floor/plate form fixed over and including 20mm thick screed in CM 1:6, complete, all as specified & directed.

S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete, all as specified & directed.

S&F in repair 32mm dia HDPE pipe for WHB, sink waste/drain pipe fixing with clamps, complete, all as specified & directed.

S&F stainless steel kitchen plate rack made of 0.80mm thick sheet of size 750x600x250mm and fixed to wall, complete, all as specified & directed.

S&F in repair chromium plated brass single hole basin mixer with hot and cold arrangement with long shank and cup suitable for 15mm bore pipe complete, all as specified & directed.

S&F in repair chromium plated brass wall mixer 2 in 1 with hot and cold arrangement with cup suitable for 15mm bore pipe complete, all as specified & directed.

S&F in repairs brass chromium plated shower rose 125 mm size without swivel joint including fixing to steel pipe of 15mm bore or union complete, all as specified & directed.

S&F glass corner self assembly, fancy type, made of 6 to 7mm thick sheet glass of size 250x250mm, fixed with CP brackets, complete, all as specified and directed.

S&F in repair 110mm bore PVC (SWR) pipe single socketed in any length with rubber rings joints laid in fixed to walls including demolition and breaking up 100mm bore pipe drain pipes, salt glazed stone ware set in cement mortar complete, all as specified & directed.

S&F in repair 75mm bore PVC (SWR) pipe single socketed in any length with rubber rings joints laid in fixed to walls including demolition and breaking up 100mm bore pipe drain pipes, salt glazed stone ware set in cement mortar complete, all as specified & directed.

S&F PVC (SWR) bends any radius of 100 mm dia,complete, all as specified & directed.

S&F PVC (SWR) bends any radius of 75 mm dia,complete, all as specified & directed.

S&F mild steel framed work as in doors / gates / steel frames / chowkats etc. of angle or other section with gusset plates, rails, braces, etc., complete conforming to Grade E - 410 (Fe 250), drilled for fixing of steel sheeting or other covering including necessary welding etc and fixing in position complete, all as specified & directed.

M&L for preparation of old surfaces (plastered or unplastered) of walls including cornices, pilasters etc including brooming or steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots and applying one coat of white wash, complete all as specified & directed.

All as per description of serial item no. 99 above but applying applying two coat of white wash on wall surfaces.

All as per description of serial item no. 99 above but applying applying one coat of white wash on ceiling surfaces.

M&L for complete removal of existing treatment of old decorated surfaces of walls by washing, rubbing down & stopping of painted surfaces and applying two coat of cement base paint, complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls by washing, rubbing down and stopping of distempered surfaces and applying one coat of oil emulsion distemper (OBD) of approved shade/tint complete, all as specified & directed.

M&L for preparation of old painted surfaces of wood & wood based material of any description over 10 cm width or girth and applying one coat of synthetic enamel paint, complete, all as specified & directed.

M&L for preparation of old painted surfaces of steel and iron work of any description over 10 cm width or girth and applying one coat of synthetic enamel paint, complete, all as specified & directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc.complete, all as specified & directed.

M&L for cement concrete (1:3:6) type C-1 using 20 mm graded crushed stone aggregate as in surface channels, drains, coping and benching including necessary formwork whrever required complete, all as specified & directed. Note : Forming fair finished channel for drain using extra cement shall be measured and paid for separately.

Supply and laying of 3mm thick (Minimum) polymeric water proofing membrane weighing not less than 3 Kg/Sqm laid on a coat of bitumen primer @ 0.50 kg per Sqm for sunken portion complete, all as specified & directed.

Taking out loose filling of aggregate in any form, from sunken slab and refiiling after treatment complete, all as specified & directed.

G D SINGH AND CO

M/S Dwivedi Construction Coy

M/s Durga Construction Company

M/s R.K.Traders

JITENDRA SINGH