REPAIR TO FLOORING, PLASTERING, PLINTH PROTECTION, FENCING AND MISC B/R WORKS IN TECH AREA AF STN PALAM UNDER GE (AF) PALAM DELHI CANTT-10

Amount

Dismantling of old rusted plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, gate and walls of the hanger complete all as specified and directed by Engineer-in-charge.

S&F for curvature type pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour approved by GE having tensile strength of 550Mpa as in roof covering/clading to wall fixed with self tapping screws as per existing shed profile complete all as specified.

M&L for mild steel work as in hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165.

Taking down cement or cement lime plaster on brick/ stone or concrete surfaces etc including raking out joints, hacking for key, scrubbing down with water etc upto 4th storey building including removing the debris from site to outside MoD land.

M&L for 15 mm thick rendering in cement mortar 1:6 on brick or concrete surfaces including finishing surface even and smooth without using extra cement.

M&L for 15 mm thick cement plaster on fair faces of brick work or concrete surfaces of walls in cement mortar 1:4 including finishing surface even and fair without using extra cement but with liquid water proofing compound by weight as per manufacturer's instructions upto and including 4th storey bldg with necessary scaffolding . (Note : WPC will be measured and paid separately)

Supply only Integral water proofing compound.

M&L for preparation of newly plastered surfaces of ceiling and applying two coats of oil bound distemper over a coat of wall primer all as specified and directed by Engr-in - Charge

M&L for applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/ltr and UV resistance as per IS 15489-2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.9 litre /10 sqm over newly plastered surfaces of walls all as specified and directed.

Demolition of cement concrete (un reinforced) in ground floors and pavings n. exc 15 cm thickness (below or above ground level) and removing the debris from site to out site MoD Land.

M&L for 75mm thick cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection including finished even and smooth without using extra cement including making joints 12 mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen mastic 85/25 and sand in the proportion of (1:3 ) by weight complete.

M&L for 75mm thick cement concrete (1:3:6) type C-2 using 40mm graded stone aggregate as in path and paving finished even and smooth without using extra cement.

M&L for 25 mm thick cement concrete 1:2:4 type B-1 using 20mm graded aggregate as in floor including finished even and smooth with using extra cement.

M&L for cement concrete type C-1 (1:3:6) using 20 mm graded stone aggregate in surface channel/drain etc complete all as per specified and directed..

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc all as per specified and directed..

S&F in repairs 75mm thick SFRC drain cover of any size laid over existing drain complete all as specified and as directed by Engr-in-Charge.

Dismantling wall and ceiling boards ( fibre , pulp,insulation etc.) or insulation boards / slabs / blankets , any thickness , including fillets complete all as specified

M & L for provding false ceiling of 15mm thick fine fissure board sharped finished mineral fiber accountic false ceiling tiles with back of the duly sanded and finshed with a coat of protective paint and front duly finished false system of size (600x600) mm having noise reduction co-efficient of 0.55 light reflection of 80% thermal conductivity k=0.057 W/WWC and humidity resistance of 95% fixed to true look PVC die KL -24 suspension system (Hot dipped aglvanised steel section) of exposed T Section consisting of perimeter wall angle of size (24x24) mm of thickness 0.45 of mm c/c universal main runner of T Shape with double rotary siticing of size (38x25) mm of lenght 1200mm made from 0.33GS steel of lenght 3.60 mtr to be spced at 600x 600mm size) c/c cro runner T shape wtih double rotary siticing of size (30x24)mm of length 1200mm made 0.25 thick GS sheet spaced @ 600mm c/c (600mm 600mm) size complete all as specified and directed by Engineer -in- Charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Sqm each including cutting holes in walls of appropriate size for insertion of cement concrete blocks for hold fasts complete all as specified.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size exceeding 1.50 Sqm but n. exc 4.0sqm each including cutting holes in walls of appropriate size for insertion of cement concrete blocks for hold fasts complete all as specified.

S&F for anodised aluminium power coated (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators, partition wall etc with one or more rebates including joining cleat for fixing etc all as specified.

S&F for anodised aluminium power coated (minimum thickness of powder coating 50 micron) door shutter, aluminium section wt 0.55 Kg/m including neccesary joining cleats, glazing clips,rubber neoprene packing, handle 2 nos in each door, hinges, anodised aluminium snap beading screw etc. complete all as specified.

S&F for anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised, handle 2 nos in each window aluminium fittings such as peg stays150mm long (1 No), hinges type B-21,100mm long (2 Nos),suitable handle (1 No) etc for each shutter complete all as specified.

S&F for aluminum grill of design and parttern as approved including aluminium beading complete.

M&L for 12mm thick prelaminated particle board, exterior grade, prelaminated both side with decorative choice lamination & fixed with screws to frame complete all as specified and as directed

S&F in repair door closure hydraulically regulated designation No 3 universal type suitable for door shutter of 851 to 1000 mm in width of Aluminum body (die cast) weight between 61 to 80 kg complete.

S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminum alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other party made of mild steel heavy duty complete.

S&F in repair mild steel mortic lock vertical type size 100mm 4 levers complete.

S&F in repair aluminium tower bolt of extruded section, 150mm length of bolt and fixed with screws complete.

S&F in repair aluminium door stopper double legged with rubber shoe 75mm long fixed to door shutters complete all as specified and as directed.

Dismantling of floor, hearth or wall tilling including cement mortar bedding (but not backing) including removing the debris from site to outside MoD land.

M&L for vitrified tiles (light shade) 8 to 10 mm thick of first quilaty (Square/rectuangular) polished, double charge shade, area of each tiles exceeding 0.36 Sqm but not exc. 0.42 Sqm as in floors etc. set and jointed with neat cement slurry and pointed in white or coloured cement to match the tile over and including 15mm thick screed bed in cement mortar 1:6.

All as per item No 33 above but as in skirting.

M&L for ceramic coloured/ printed non-skid tiles of 7 to 8 mm thick( square / rectangular ) area of each tile exceeding 0.06 Sqm but not exc. 0.16 Sqm as in floors etc set and jointed with neat cement slurry and pointed in white or coloured cement to match the tile over and including 15mm thick screed bed in cement mortar 1:6.

M&L for glazed ceramic coloured tiles (colour & shade as approved) of size 300mm x 250mm x 7-8mm thick in vertical surfaces such as in skirting and dado, set and jointed with neat cement slurry and pointed in white or coloured cement to match the tile over and including 10mm thick rendering in cement mortar 1:4.

S&F in repair wash hand basin, vitreous China, flat back 550x400mm size, white including PVC waste coupling 32mm size, PVC waste pipe 32mm bore, pair of brackets of mild steel 35 x 35 x 6mm size including one CP mixer 15mm dia, one CP stop valve 15mm dia and one PVC connection15mm size with PTMT nuts of length 450mm long complete all as specified and directed by Engineer-in-Charge.

S&F in repair vitreous china EWC Super constellation including cistern of size 83x37x66 cm S trap as aer Cat Part No 20040 (S-10/P-9) Make Hind ware or its equivalent in Cera/ Parry ware.

S&F in repair vitreous china urinal pot, white including partition, waist pipe screw with wall fixing complete, Make-Hindware Cat Part No 61001 or its equivalent in Cera/ Parry ware as approved by GE.

S&F in repairs three way wall mixer with popup waste system, hot and cold facilites and 450 mm long braidaed hoses chromium plated of Cat Part No. FUS-29273 UPR of make Jaquar or its equivalent in kohler/ Marc.

S&F in repair health faucet with double lock 1 meter brass plated stainless steel flexible hose and wall hook complete all as specified and directed Cat Part No.563 of make Jaquar or its equivalent in kohler/ Marc.

S & F in repair CP paper holder of Make-AKP-35751P of Jaquar or its equivalent in kohler/ Marc.

S&F in repair of 100mm cast iron floor/nahani trap with grating including jointing and breaking/ dismantling any type of floor and making good cement concrete type B-1 (1:2:4) and testing after repairs complete all as specified.

S&F in repair brass chromium plated tubular towel rail, 20mm dia, 'D' type, 60cm long between flanges complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections in walls, ceilings, floors, etc including cleaning for re-fixing complete.

M&L for 15mm bore GI tubing `medium grade` with all fittings and fixed complete to walls and ceilings or laid in floors etc complete.

M&L for cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps,cills,sunshades,shelves,lintels,etc,and cutting chases for conceald water tubing or concealed conduit wiring, etc and making good cutting not exc 10 cm girth as in wall complete.

S&F in repair 15mm bore angle cock,cromium plated, screwed down, high pressure, with crutch or butterfly handles, screwed both ends for iron pipe or for unions and fixed all specified .

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm.

S&F in repair CP Soap dish of Make-AKP-35731P Jaquar or its equivalent in kohler/ Marc.

S&F in repair 15mm dia bib taps with wall flange, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle , screwed down , screwed for iron pipe or for brass ferrule complete.

S&F in repair 15mm dia pillar cock, foam flow, chromium plated, fancy type, capastan heads, screwed down high pressure all as specified and directed. Cat Part No 8304 of Prayag or equivalent in Jaquar/Parko.

M&L for 18 to 20mm thick granite (of jet black) work (table rubbed and polished ) in steps ,jambs ,pillars,window cills, cooking platforms and like laid over 15mm thick screed bed in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite complete.

M &L in repair 500 litres capacity rotational moulded polyethene water storage tank (cylindrical vertical with closed top), white, three layers, hoisted and fixed in position all as specified.

S&F in repair 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed.

Demolition of brick work/ stone masonry built in cement or cement lime mortar including all quoins, arches, pillars etc of any description including removing the debris from site to outside MoD land.

M&L for brick work with sub class `B' bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete.

S&F for mild steel work as in hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops for making double swan neck i.e. "Y" shaped or shape as directed, drilling holes, notching for wire, etc flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting etc conforming to Fe-290 Gde E-165 including treated embedded portion of posts and struts with tar or coal tar black paint complete.

M&L for preparation of newly steel and iron surface of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer.

S&F for concertina coil with punched tape of 600 mm dia (when stretched), centre core wire of minimum 2.5 mm dia of mild steel wire conforming to IS 280-2006 with galvanised coating of steel concertina coil as per requirements laid down for medium coated wire in IS : 4826 "Hot dipped galvainsed coating of round steel wires". Conretina coil shall be fixed in diamond shape with the help of dovetail two handle and spikes shall be fixed at both end of coil,minimum straight length of the wire 150 RM for 10 RM of work ,minimum weight 13.5 Kg for 10 RM of work complete all as specifed and directed by Engr-in-Charge. (Note : The actual weight of concertina coil brought by the contractor at site shall be ascertained by BOO as ordered by GE).

M&L for cutting holes in brick walls exc half brick but not exc one brick, built in cement mortar for fixing holdfasts in jambs of existing opening and making good complete.

M & L cement concrete 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in hold fast block including necessary form work complete.

S&F in repair galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured).

S&F in repair 35mm thick precast cement concrete jallies in cement concrete type B-0, 1:2:4 (using 12.5 mm graded crushed stone aggregate) including wire fabric etc, set and jointed in cement mortar 1:4 complete.

M & L for gunniting work to RCC beam, column, lintel, pardi, railing, slabs, side walls etc by removing loose, disturbed or disintegrated old concrete surfaces, cleaning thoroughly exposed reinforcement by sand blasting using suitable pump and applying one coat of anti corrosive paint to the exposed reinforcement, S&F welded wire mesh fabric or wire net of size 100mm x 100 mm x 3 mm dia of weight not less than 1.37 Kg/Sqm and tied to existing reinforcement with 22 guage mild steel (annealed) binding wire and applying gunniting pressure 2.00/ 2.50 Kg/Sqm with admixture 1 part of cement and 3 part of sand with average thickness 40mm and making the surface even including rendering 15 mm thick in cement mortar 1:4 on concrete surface including finishing the surfaces even and smooth without using extra cement upto four storey building and providing necessary scaffolding and safety arrangement including removing the debris from site to outside MoD land complete all as specified and directed. (Note :- The finish of the surfaces to be matched with the existing surface).

Shiv Shankar Nirman Co.

Mahesh Enterprises

VIJAY KUMAR GUPTA

a.k constructions

H.B. Traders