SPECIAL REPAIR TO COMMUNITY HALL AND TRAINING CENTRE AT DRDE GAWALIOR UNDER GE (I) R and D DELHI

Amount

B/R (Portion) Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), and including removing rubbish outside MoD land complete all as specified and directed.

Roughening surfaces of old concrete /roofing by picking, sweeping clean and washing down with water to remove dust complete all as specified and directed .

M&L for laying Vitrified Ceramic tiles (light shade) 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, first quality coloured of grade B II (a) /B II (b) and of abrasion resistance PE-I-III or above etc. set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 15 mm thick screed bed in cement mortar (1:4) complete all as specified and directed .

Dismantling exising roof treatment of any description , any thickness and including removal of rubbish outside MoD land complete all specified and directed.

Demolition of concrete, terrazzo cast in situ floors and paving n.exc 15 cm thickness (below or above ground level ) and including removal of rubbish out side defence land complete all as specified and directed.

M&L for providing Vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm first quality coloured of grade B II (a) /B II (b) and of abrasion resistance PE-I-III or above, for work on vertical surfaces such as skirting / dado etc. set and jointed in neat cement slurry and pointed in colour cement to match tile over and including 15 mm thick rendering in cement mortar (1:6) complete all as specified and directed .

M&L for laying anti non skid ceramic joint less tiles 8mm thick coloured design (square /rectagular) area of each tile exc 0.11 sqm but n exc 0.18 sqm first quality coloured of grade B 11(a) /B 11(b) and of abrasion resistance PE-I-III or above in floors set jointed in neat cement slurry and pointed/ jointed in coloured cement to match tiles over and including 15mm thick screed bed of Cement Mortar (1:6) complete all as specified and directed .

M&L for providing Glazed coloured ceramic tiles 7mm thick of size 450 x 350mm or 350 x 250mm or area n.exc 0.18 Sqm each super glossy 1st quality of grade B tiles on vertical surfaces such as skirting /dado etc set and jointed in neat cement slurry and pointed in colour cement to match tiles over and including 10 mm thick screed in cement mortar (1:4) complete all as specified and directed .

M&L for 25 mm thick plain cement concrete (PCC) (1:2:4), type B-1 (using 20 mm graded crushed stone aggregate) as in sub floors and sub base floors to receive floor topping, complete all as specified and directed .

Demolition of plain cement Concrete (unreinforced) in roofs, floors (other than ground floor), beams, stair cases, including chajjas and similar suspended work and including removal of debris and rubbish out side defence land complete all as specified and directed.

M&L for 16 to 18 mm thick machine cut kota stone slab of size 520mmx520mm to 550mmx550mm laid as in flooring, tread / landing over and including 15 mm thick screed bed or bedding layer in cement mortar (1:6), set and jointed with grey cement slurry mixed with pigment to match the shade of slab including necessay grinding, rubbing, rounding to exposed edges with moulding and polishing glossy finish complete all as specfied and directed.

M&L for cutting/ grinding of old terrazzo / Kota stone/Marble flooring including vertical surfaces of wall in dado/skirting/steps of stair case etc with grinding machine and cutting I to V staging with carborundum stone of 60 grit, 120 grit, 320 grit, 600 grit, 1200 grit and 0 grit reespectively and including polishing complete all as specified and directed.

M&L for providing machine cut kota stone slab 16-18mm thick as in skirting,risers of steps laid over and including 10 mm thick rendering in cement mortar (1:3), set and jointed with grey cement slurry mixed with pigment to match the shade of slab including necessay grinding, rubbing, rounding to exposed edges with moulding and polishing in granite finish complete all as specfied and directed.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons skirting etc laid bedded and pointed in any mortar and including removal from the out side defence land with mortar complete all as specified and directed

M&L for laying 16 to 18 mm thick machine cut mirror polished granite stone slab prefect black as in shelves , counter for wash hand basin, cooking platform, floor and window cill etc bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade / matrix of granite stone including grinding, moulding & polishing and bevelling half round edges of stones laid over and including 15 mm thick screed bed in cement mortar (1:4) complete all as specified and directed

M&L for providing 16 to 18 mm thick machine cut mirror polished granite stone slab perfect black on vertical surfaces such as skirting/dado, window sides , pillars etc set and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding, moulding & polishing and bevelling half round edges of stones fixed over and including rendering 10 mm thick in cement mortar (1:3) complete all as specified and directed

Taking down steel/wooden chowkhats or frames (without taking off shutters from the frame) area n.exc 1.5 sqm each complete all as specified and directed

Taking down steel/ wooden/ Aluminium chowkats or frames or partitions( (without taking off shutters from the frames) area exc 1.5 Sqm but n exc 4 Sqm complete all as specified and directed Notes for Ser item No 17 to 18 :- Rate also included in this items for necessary cutting doors/taking out hold fast from the existing concrete /brick work and making good the disturbed surfaces with match existing surfaces after erecting new frames /chowkhats/partitions.

Taking down of shutters of any description 1.00 Sqm but n.exc 2.00 Sqm each including builders hard ware fittings and removal from the site complete all as specified and directed.

S&F 40mm thick factory made flush shutters conforming to IS-20002 (Part-I) solid core construction with black board coe and ply wood face panels, commercial type on both side with teak wood lippling 6mm thick and 40mm wide all around the shutters complete all as specified and directed.

S&F aluminium anodised barrel tower bolts, size 200mm and dia of shoot/ bolts not less than 10mm of extruded section complete all as specified and directed

S&F aluminium handle cast type size 150mm complete all as specified and directed

S&F stainless steel butt hinges, medium duty size 100mm of AISI 316 grade complete all as specified and directed

S&F aluminium alloy anodised sliding door bolts with hasp, staple of size 300mm long and dia of shoot not less than 12mm and fixing clips of sheet cast or extruded sections and sliding bols of extruded section complete all as specified and directed

All as per ser item No. 21 here-in-before but 150mm long.

S&F aluminium anodised handle oval type size 100mm of extruded section complete all as specified and directed.

S&F in repairs aluminum (die cast) body door closer hydraulically regulated, designation No 3 universal type, suitable for door shutters upto 851 to 1000mm in width and of weight not more than 61 t0 80 Kg complete all as specified and directed.

Easing and adjusting to shutter of any description, area exc 1.00 but n.exc 4.00 sqm each and includes taking down, refixing in the same opening and renewal of unservicable parts such as aluminium fillets rubber beading including builders hardware fittings as required and tightening of screws/ nut/ bolts and edging of cutting of door to make easy to open and closed etc complete all as specified and directed. Note : New builders hard ware fittings shall be measured and paid separately under respective item of BoQ.

M&L for 9 mm thick prelaminated particle board exterior grade with decorative choice laminations both sides for insertion to panels of aluminium shutters/partitions and other location etc complete all as specified and directed .

Hacking out old broken glass any thickness, size, quality or descriptions from wooden or aluminium or steel frames or brick surrounds glazed with putty or fixed with beeds complete all as specified and directed.

Demolition of brick work or stone boulder masonry, built in cement mortar all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles including removal from the site complete all as specified and directed.

M&L for cutting out cracks to v-section in existing roof or terracing, cleaning out and filling grouting solidly with a hot mixture of bitumen and clean dry sand mix (1:1) by weight complete all as specified and directed.

M&L for brickwork with fly ash old size bricks having compressive strength not less than 75 Kg/Cm2 straight or curved on plan exc 6m mean radius, built in cement mortar (1:6). complete all as specified and directed .

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal fo debris and rubbish out side defence land complete all as specified and as directed .

M&L for rendering 15mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces finished even & fair complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:4) on other than fair faces of brick work or concrete surfaces (vertical walls surfaces) finished even & fair complete all as specified and directed.

M&L for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement : 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand: 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified Notes : (i) Proposed washed stone grit plaster colour shall match with existing . (ii) White cement shall be used in lieu of ordinary cement in top layer of washed stone grit. (iii) Grooves shall be measured and paid separately,

M&L for forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specification and direction of the Engineer -in-charge.

Complete removal of existing treatment from walls, fins, chajja etc by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots including removing waste material/ debris outside MoD land complete all as specified and directed. Note Rate also includes necessary scaffolding to carryout work up to portion of building G+3 storey high.

All as per ser item No. 41 here-in-before but on ceiling/chajjas/sunshade including necessary scaffolding.

M&L for applying wall care putty not less than 3mm thick over newly plastered or old ( surface obtained after complete removal of existing treatment) on wall/vertical surfaces to achieve an even finished smooth surface for applying finishes complete all as specified and directed.

All as per ser item No. 43 here-in-before but on ciling/chajja/sunshade including scaffolding.

M&L for applying two coat of oil bound distemper over wall care putty surfaces , preparatory to distempering complete all as specified and directed. Note : Wall care putty shall be measured & paid separately.

M&L for preparation of old plastered surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M&L for applying two coats of acrylic exterior emulsion weather proof paint of any tint including priming with alkali resistant primary paint on external new plastered/ putty surfaces for portion of building G+3 including necessary scaffolding complete all specified and directed.

M&L for preparing of new plastered surfaces and applying two coats of plastic emulision paint over one with alkali resistant priming paint on walls pillasters, projections etc complete all as specified and directed.

All as per ser item No. 48 here-in-before but on ceiling cornices, etc.

S&F in repairs Vitreous China wash down water closet pan (pedestal pattern), white including PVC seat cover with mild steel chromium plated hinging dence & EWC Jet chromimum plated with 1.00 m long (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and as directed.

S&F in repairs Vitreous China water closet squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including provision of concrete bedding and removal of waste materials/debris out side MoD land complete all as specified and directed.

S&F in repairs vitreous china table top /oval type (under/over counter wash basin) white size 550x400mm including CP waste fitting 32mm dia and CP bottle trap etc complete all as specified and directed .

S&F in repairs vitreous china half stall urinals, olympus star, white complete including providing and fixing plugs, securing urinals to plugs with and including 60mm long brass screws, fixing flush pipe, CP urinal Spreader fixed to water supply pipe, CP waste coupling, grating and union for discharge pipe complete all as as specified and directed .

S&F in repairs PVC valveless, syphonic action type, flushing cistern 10 ltr capacity, low level white with inlet ball valve, float, , handle and brackets including fittings flush pipe 32mm bore complete all as specified and directed .

S&F in repairs bib taps long body chromium plated brass cast copper alloy fancy type with crutch or butterfly handle screwed down suitable for iron pipe or brass ferrule of 15 mm bore complete all as specified and directed .

S&F in repairs chromium plated brass pillar tap fancy long body push type time duly screwed for iron pipe and fixed to 15mm dia bore complete all as specified and directed .

S&F 15mm bore brass chromium plated brass single lever basin mixture without pop up waste system with 450 mm long braided hoses etc for WHB complete all as specified and directed.

S&F in repairs chromium plated fancy Angle/stop valve high pressure with crutch or butter fly handle screwed both end for angle valves cast copper alloy, screwed iron pipe or for unions and fixed 15mm bore dia complete all as specified and directed .

S&F in repairs PVC connections 15mm size with brass socket on both side of length 600mm complete all as specified and directed .

All as per ser item No. 58 here-in-before but with long shonk and cup (concealed type)

All as per ser item No. 57 here-in-before but wall mounted.

All as per ser item No. 58 here-in-before but 20mm bore dia.

S&F in repairs toilet paper holder Chromium plated brass complete all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail, having wall thickness not less than 1 mm, 20mm dia, D type, 60cm long between flanges of brass chromium plated bracket fixed with two plugs (Gutties) of 2nd class hard wood embedded in cement mortar (1:3) complete all as specified and directed .

S&F in repairs chromium plated soap dish, any type, fixed to plug with chromium plated brass screws complete all as specified and directed .

S&F in repairs swivel shower of PTMT, any colour for fixing with 15mm bore (minimum weight 40 gms ) and including shower arm 15mm size, 195 mm long with bend of 45 degree with necessary flange of PTMT any colour minimum weight 40 gms complete all as specified & directed.

S & F in repairs 15mm bore chromium plated brass cock regular spout for sink complete all as specified and directed.

M&L for 10mm thick cement mortar (1:4) as in screed bed or bedding layer or rendering on roofs mixed with water proofing compound as per manufecturers insturctions, surfaces finished even and smooth without using extra cement complete all as specified and directed. Note : WPC shall be measured and paid separately.

Supply only liquid water proofing comound as approved.

M & L for applying water proofing treatment to roof as under: (a) Apply a coat of approved bituminious primer @0.20 kg per Sqm and applying hot blown bitumen 85/25 @ 1.20 kg sqm. (b) Laying APP polymer modified memberane with polyster reinforced 3mm thick and not less than 3.5 kg per sqm with side end laps by torch application method as specified. (c) Applying a coat of solar reflective bituminious aluminimum paint @ 0.15 kg per sqm over the membrance complete all as specified and directed. Note :- W.P.T. to roofs shall be carried out only by authorised applicator of manufacturers as approved by GE.

Dismantling old unserviceable PVC water storage tanks of capacity exc 500 ltrs & but n.exc 1000 Ltrs including supplying & fixing of any colour PVC water storage tank 1000 ltr capacity HDPE, IS-12701 marked double layered , cylindrical vertical type fixed and hoisted in position on roof at any height of building complete with inlet/outlet of 25 mm outer dia 3 layer PPR pipe connection including closed top with locking arrangement, including supplying & fixing Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight of valve 210 gms ) complete all as specified and directed by Engineer-in-Charge Note : (Inlet, outlet & wash out pipe will be measured and paid separately.

S&F in repairs ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed of 20mm dia, minimum weight 210 gms complete all as specified and directed.

Disconncting existing water tanks of capacity exc 500 ltr & n.exc 1000 ltr setting aside (or lowering if required) for repairs, cleaining and removing all scale and dirt etc from tanks and from mouth of circlulating pipes etc and hoisting if required reconnecting and refixing in position and including writing date of cleaning on outer surfaces of tank by white paint complete all as specified and directed.

Supply and fixing in repairs gun metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe of 20mm bore dia complete and fixed all as specified and directed by Engr-in-charge.

All as per srl item No 75 here-in-before but 25 mm bore dia.

Taking down 15mm bore steel water tubing and connections from any position including cleaning and refixing in same or other location as per site requirement complete all as specified and directed.

All as per srl item No 77 here-in-before but 20 mm bore dia.

All as per srl item No 77 here-in-before but 25 mm bore dia.

Supply and fixing in repairs 15mm bore steel water tubes, medium grade, galvanised to iron with all fitings/ accerories and fixed complete to walls ceiling or laid in floors all as specified and directed.

All as per srl item No 80 here-in-before but 20 mm bore dia.

All as per srl item No 80 here-in-before but 25 mm bore dia.

S&F UPVC pipe size 110mm for soil, waste, and vent, Type-B as per IS-13592 suitable for rubber ring joints, including all necessary specials and fittings (Confirming to IS-4735) such as bends, tees , junctions (with or without doors), reducers, WC connectors, couplers, cowls, clamps, rubber rings etc, fixing at walls/ceiling/floor supproted by MS clamp & hangers etc in concealed/inside duct/under floor & basement ceiling/external work etc. including chase cutting if required upto 04 storeyed high building and making good distrubed surfaces with existing and including taking down old unservicable C.I. pipes complete all as specified and directed.

Dismantling of wall panelling and ceiling board (Fibre,pulp,insulation etc.) or insulation board /slab/blankets any thickness including cover fillet , GI Frame work and hangers /rod etc complete all as specified and directed by Engr-in-Charge.

S&F aluminium frame duly powder coated not less than 50 micron thick for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed by Engr-In-Charge.

S&F in repair for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in position.

S&F aluminium section duly powder coated not less than 50 micron thick for window grills complete with necessary 'U' shaped aluminium channel alround fixed in window frame /opening with screws complete all as specified and directed

M&L for preparation of old steel surfaces of any description over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified.

M&L for preparation of new wood or wooden based surfaces of any description, over 10 cm in width or grith not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed

Taking down aluminium section as in doors/windows/ventilators/partitions frame and shutters of any size and description complete all as specified and directed.

S&F aluminum shutters duly powder coated not less than 50 micron thick for doors, window, ventilators, partition etc including necessary joining cleats, glazing clips, snap beading screws etc complete alll as specified and directed at site. Note : Glass/ particle board, rubber neoprene packing etc shall be measured and paid separaely.

All as per srl item No 88 here in before but on wood or wooden based surfaces.

S&F aluminium anodised snap grid of size 600x 600 mm to 605 x 605mm frame work for false ceiling complete including hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long and including 12mm thick perforated particle boards or tiles for insulation and accoustic purpose 60 CM x 60 CM in size complete all as specified and directed. Note: Aluminium tee/angle size for snap grid shall be all specified in SSR Part-I or as per manufacturer's instructions.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joint fixed to wall trenches/ floors/ ceiling etc with mild steel clamps after taking down old unservicable existing PVC pipe of any description complete all as specified and directed.

S&F in repairs PVC (SWR) bends any radius 110mm bore complete all as specified and directed.

M&L for providing cement concrete 1:2:4 type B-0, (using 12.5 mm graded crushed stone aggregate) in roof kerbs r mud stops, benching rounded or chamfered on edges exposed surfaces finished even and smoothe with out using extera cement complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semicorugated etc) in roof coverings and removal from site complete all as specified and directed.

S&F stack clamp suitable for 100mm bore of pipe , made out of 50mm x 5mm flat iron and 16mm dia round stays including mild steel bolts and nuts and securing ends of stay to wall or roof or paraphet complete all as specified and directed.

S&F 110mm bore PVC (SWR) single 'T' equal or unequal with rubber ring joint complete all as specified and dia

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour approved by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawings shown on ser page No 160 of SSR Part-II (Rates)

Factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front Face & 2mm Plan colour PVC sheet on back face, with 12mm x 2 Nos paricle board core, supplying & fixing in frame at site as per specification & drawing as shown on ser page No 161 of SSR Part-II (Rates)

All as per srl item No 100 here-in-before but plain steel sheet.

M&L for providing PCC 1:2:4 type B-1 (using 12.5mm graded crushed stone aggregates) as in padding on roofs, sumps, water troughs and the like including weathering , slightly rounded or chamfered angles and throating as directed complete all as specified and directed.

Supply and fix in repairs stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm of 26 gauge and fixed with stainless steel wire staples/ MS /wooden beading complete all as specified and directed.

S&F in repairs brass mortice lock, vertical type size 100mm including escutcheon plates and minimum two keys complete all as specified and directed.

M&L for 9mm thick Prelaminated particle, board, exterior grade,prelmainated one side with decorative choice laminations & other side balancing white lamination, fixed with screws to frame work complete all as specified & directed

M&L for 75mm thick cement concrete (1:3:6), type C-2 (using40mm graded crushed stone aggregates) as in sub floors , subbase laid in alternate panel/ way finishing surfaces even and rough to receive the topping layer including necessary use and waste form work complete all as specifed and directed.

M&L for chipping of spoiled and loose concrete and cleaning rust from reinforcement by sand blasting scrubbing down concrete surfaces with wire brushes cleaning with water allow to dry and applying a layers of Zinc rich epoxy primer as an antirust on all exposed reinforcement steel bars followed by a layer of bonding coat of approved epoxy adhesive on complete exposed surfaces of concrete to be gunited and applying two layers of guniting over steel welded mesh 3mm dia of wire and appruture 75 mm, total thickness of guniting not exc 30mm (Avg thickness) in Cement mortar (1:2) using OPC 53 grade cement mixed with polycreate mixture @2% by weight of cement or as per menufacturer instructions and finally appyling cement plaster over gunite surface of requred thickness to give even , uniform and smooth finishes confirming to proper geometric in cement mortar (1:3) to match the existing surfaces as in sides ,soffits of the slabs,chajja,fins,facia ,parapets,lintels,columns, beams etc complete including necessary scaffolding ,shuttring,necessary chasing to brick work or RCC members at any hieght up to 04 storey buildings including removal of all small trees/shurbs (including roots) etc complete all as specified and as directed. Note:-Rate also includes in this item for necessary provision of scaffolding to carry out work upto portion of building G+3 storeys high.

M&L for 2nd class hard wood plain fillets, square , rectangular or tringular clean sawn in section exc 13 Sq cm & n. exc 25 Sq cm secured with nails or brads complete all as specified and directed.

M&L for veneered decorative plywood 12mm thick , grade I (with BWR resin) with decorative face veneers on one side fixed with screws to timber frame work in panelling complete all as specifed and directed.

Taking down unservicable copper / aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc. removing materials from site and making good disturbed surfaces of walls, floors, roof, ceiling etc with existing surface complete.

M&L for colour coding point wiring with 1.5 sqmm multi stranded FRLS PVC insulated conforming to IS-694 unseathed copper conductor cable in and including rigid non metalic PVC concealed conduit of size 20 mm bore dia ISI marked for one light point or fan point or bell point or 5 Amps switch socket combination controlled by one switch including FRLS PVC insulated conforming to IS-694 unsheathed 1.5 sqmm copper conductor continuous earth wire and connecting with earth dolly including necessary cutting chasing for concealing of conduit and making good the distrubed surfaces matching with existing specifications complete all as specified and directed

M&L for colour coding point wiring with 2.5 sqmm multi stranded FRLS PVC insulated conforming to IS-694 unseathed copper conductor cable in and including rigid non metalic PVC concealed conduit of size 20 mm bore dia for power plugs including FRLS PVC insulated conforming to IS-694 unsheathed 2.5 sqmm copper conductor continuous earth wire and connecting with earth dolly including necessary cutting chasing for concealing of conduit and making good the distrubed surfaces matching with existing specifications complete all as specified and directed

M&L for point wiring with 1.5 sqmm multi stranded FRLS conforming to IS-694 PVC insulated unsheathed copper condoctor cable in and including rigid non metalic PVC concealed conduit of size 20 mm bore dia ISI marked for one light point controlled by two 2- way switches including FRLS PVC insulated unsheathed 1.5 sqmm copper conductor continuous earth wire and connecting with earth including necessary cutting chasing for concealing of conduit complete all as specified and as directed.

M&L for point wiring with 1.5 sqmm multi stranded FRLS conforming to IS-694 insulated unsheathed copper conductor cable in rigid non metalic PVC concealed conduit of size 20 mm bore dia ISI marked medium grade for one 3 pin socket outlet, 5 Amps, independent including FRLS PVC insulated unsheathed 1.5 sqmm copper conductor continuous earth wire and connecting with earth dolly including necessary cutting chasing for concealing of conduit complete all as specified and directed.

M&L for point wiring with 1.5 sqmm multi stranded FRLS conforming to IS-694 PVC insulated unsheathed copper conductor cable for one 3 pin socket 5 Amps point on the same board with other switches, including FRLS PVC insulated unsheathed 1.5 sqmm copper conductor continuous earth wire and connecting with earth dolly including necessary cutting chasing for concealing of conduit complete all as specified and directed

M&L for colour coding point wiring with 4 sqmm multi stranded FRLS conforming to IS-694 PVC insulated unsheathes PVC insulated copper conductor cable in and including rigid non metalic PVC concealed conduit of size 25 mm bore dia ISI marked 15/16 Amp socket for sheet metal enclosure SP/TP including FRLS unsheathed 4 sqmm copper conductor continuous earth wire and connecting with earth dolly including necessary cutting chasing for concealing of conduit and making good the distrubed surfaces matching with existing specifications complete all as specified and directed. Note for ser item No. 113 to 118: Modular flux box, cover plate for fixing and including of switch socket and fan regulator shall be measured and paid seprately under respective item of BoQ.

S&F Modular switch 1 way 6 Amp, 1 module AC 230 volts complete all as specified and directed.

S&F Modular switch 2 way 6 Amp, 1 module AC 230 volts complete all as specified and directed.

S&F Modular Socket 6 Amp ,2/3 pin combined 2 module AC 230 volts complete all as specified and directed.

S&F Modular switch 1 way 16 Amp 1 Module AC 230 volts complete all as specified and directed.

S&F Modular Socket 6 A / 16 A , 5/6 pin combined 2 module AC 230 volts complete all as specified and directed.

S&F ceiling rose 65 x 50mm, 3 terminal PVC/Polycarbonate AC 230 volt complete all as specified and directed.

S&F Modular step fan regulator, electronic type 120 watt , 2 module AC 230 volts suitable for 1200mm/ 1400mm sweep ceiling fan, hum free complete all as specified and directed.

S&F Modular white cover plate with 2 module complete all as specified and directed.

S&F Modular white cover plate with 3 module complete all as specified and directed.

S&F Modular white cover plate with 4 module complete all as specified and directed.

S&F Modular white cover plate with 8 module complete all as specified and directed.

S&F Metal flush box 1/2 module complete all as specified and directed.

S&F Metal flush box 3 module complete all as specified and directed.

S&F Metal flush box 4 module complete all as specified and directed.

S&F Metal flush box 8 module complete all as specified and directed.

S&F lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F in replacement of sheet metal enclosures Single pole and neutral with two pin earth plug and socket with plug top including double pole MCB 20 Amps complete all as specified and directed.

S&F in replacement of sheet metal enclosures Triple pole and neutral with three pin earth plug and socket with plug top including triple pole MCB 32 Amps complete all as specified and directed.

M & L for sub main wiring / circuit wiring with two single core FRLS PVC insulated cable 2x4 sqmm (Nominal dia) copper conductor multistrand and drawing in existing surface/ recessed steel/ PVC conduit including 1x4 sqmm multistrand copper conductor FRLS PVC green unsheathed cable for earth continuity complete all as specified and directed.

M&L in renewal wiring for circuit/submain wiring along with earth wire with 2x4.00 Sqmm+4sqmm earth wire of FRLS PVC insulated copper conductor single core cable in and including non metalic rigid PVC conduit pipe 25 mm external dia with all accessories complete all as specified and directed.

M&L in renewal wiring for circuit/submain wiring along with earth wire with 4x6 Sqmm+2x6 sqmm earth wire of FRLS, PVC insulated copper conductor single core cable in and including non metallic rigid PVC conduit pipe 25 mm external dia medium grade including all accessories complete all as specified and directed.

M&L in renewal wiring for circuit/submain wiring along with earth wire with 2x1.5 sqmm+1x1.5 sqmm earth wire of FRLS, PVC insulated copper conductor single core cable in and including non metallic rigid PVC conduit pipe 25 mm external dia including all accessories complete all as specified and as directed.

M&L for sub main wiring / circuit wiring with four single core FRLS PVC insulated unsheathed cable 6 sqmm (Nominal dia) copper conductor multistrand and drawing in existing surface/ concealed conduit including 2x6 sqmm multistrand copper conductor FRLS PVC green insulated unsheathed cable for earth continuity complete all as specified and directed.

M&L for sub main wiring / circuit wiring with four single core FRLS PVC insulated unsheathed cable 10 sqmm (Nominal dia) multistranded copper conductor and drawing in existing surface/ concealed conduit including 2x 10 sqmm multistrand copper conductor FRLS PVC green insulated unsheathed cablefor earth continuity complete all as specified and directed.

M&L Sub main wiring /circuit wiring with four single core FRLS, PVC insulated unsheathed cable 16 sqmm (Nominal dia) multistranded copper conductor and drawing in existing surface/ concealed conduit including 2x16 sqmm multistrand copper conductor FRLS PVC green insulated unsheathed cablefor earth continuity complete all as specified and directed.

S&F rigid non-metalic 20 mm bore dia PVC conduit including all tees, bends, elbows, reducers, bell mouth tube ends , junction boxes and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. complete all as specified and directed.

S&F rigid non-metalic 25 mm bore dia PVC conduit including all tees, bends, elbows, reducers, bell mouth tube ends , junction boxes and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. Complete all as specified and directed.

S&F rigid non-metalic 32mm bore dia PVC conduit including all tees, bends, elbows, reducers, bell mouth tube ends , junction boxes and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. Complete all as specified and directed.

S&F in replacement of sheet metal enclosures double door for DBs when MCB used in SPN 8 way, 230 Volts complete all as specified and directed.

S&F in replacement of sheet metal enclosures double door for DBs when MCB used in SPN 12 way, 230 Volts complete all as specified and directed.

S&F in replacement MCB SP 6 to 32 Amps 10 KA, C-series all as specified. Make :- Havells cat part no.DHMGCSPF006-032 or equivalent in make / manufacturers as given in Appendix 'B' to PS.

S&FMCB SPN 40 Amps 10 KA, 'C' series all as specified .Make :- Havells cat part no.DHMGCSNF040 or equivalent in make / manufacturers as given in Appendix 'B' to PS.

S&F MCB TP 63 Amps 10 KA, 'C' series all as specified .Make :- Havells cat part no.DHMGCTPF063 or equivalent in make / manufacturers as given in Appendix 'B' to PS.

S&F MCB TPN 63 Amps 10 KA, 'C' series all as specified .Make :- Havells cat part no.DHMGCTNF063 or equivalent in make / manufacturers as given in Appendix 'B' to PS.

S&F in replacement of sheet metal enclosures for DBs when MCB to used TPN 4 way double door poweder coated, 415 Volts, with busbar neutral link earth rail & din rail, ISI marked, provision for four pole MCB /isolator /RCCB as incommer ands SP/DP MCBs as outgoing fixed on wall/metal board/ wooden board complete all as specified and directed.

S&F in replacement of MCB, TPN 40 Amps , 10 KVA, 'C' series complete all as specified and directed. Havells cat part No DHMGCSNF040 or equivalent in make / manufacturers as given in Appendix 'B' to PS.

S&F Sheet metal enclosure TPN DBs 4 Way 415 Volts , vertical double door type powder coated with busbar neutral link earth rail & din rail, IP-42 Protected, ISI marked for incorporation of DPX 160 MCCB/ ISOLATOR/ RCB etc. Fixing testing & commissioning complete all as specified. Make :- Havells cat part no.DHDLVDRWGOFO04 or equivalent in make / manufacturers as given in Appendix 'B' to PS.

S&F Sheet metal enclosure TPN DBs 8 Way 415 Volts , vertical double door type loadline powder coated with busbar neutral link earth rail & din rail,IP-42 Protected, ISI marked for incorporation of DPX 160 MCCB/ ISOLATOR/ RCB etc. Fixing testing & commissioning complete all as specified. Make :- Havells cat part no.DHDLVDRWGOFO08 or equivalent in make / manufacturers as given in Appendix 'B' to PS.

S&F in replacement of MCCB 4 pole , 125 Amps, 415 Volts, 16 KA breaking capacity and connection complete all as specified and directed.

S&F surface and wall mounted 20 Watt LED tube light fitting extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver input voltage AC 230 V, 50 HZ complete all as specified and directed Make Havells Cat pat no.LHEXACP7IN1W020 or equivalent in make / manufacturers as given in Appendix 'B' to PS.

S&F Decorative Surface mounted 34 watt LED lumaire , full output luminair for modern offices with CRCA powder coated body and new generation high effciency diffuser to provide soft glare free light suitable for 600 x 600 mm modular / POP/ Gypsum ceiling complete including disconnecting and taking out old U/S light fittings all as specified.Make: Havells cat part no.PLUTOSURFACE2x2PLS34WLED857S or equvalent in make / manufacturers as given in Appendix 'B' to PS.

S&F Decorative recess mounted 34 watt LED lumaire , full output luminair for modern offices with CRCA powder coated body and new generation high effciency diffuser to provide soft glare free light suitable for 600 x 600 mm modular Armstrong/Grid ceiling complete including disconnecting and taking out old U/S light fittings all as specified. Make: Havells cat part no PLUTONEO2x2PLS34WLED857S or equvalent in in make / manufacturers as given in Appendix 'B' to PS.

S&F bulk head luminarie with LED 10 watt lamps Hexagonal shaped with engineering plastic housing and frame with opal PMMA defuser complete including disconnecting and taking out old U/S light fittings all as specified and directed by Engineer in charge.Make: Havells cat part no HEXAFT10WLED857SSYMBOPC or equvalent in make / manufacturers as given in Appendix 'B' to PS.

S&F energy saving decorative wall mounting LED Lighting fixtures for mirror light made out of poly corbonate suitable for 5 watt LED and making connections complete all as specified and directed by Engineer in charge. Make: Havells cat part no LHEXBLP7IN1W005 or equvalent in Philips / Bajaj .

S&F recessed mounted LED downlighter 24 W with pressure die cast aluminium heat sink, & PC diffuser in white powder coated finish with integrated driver including necessary cutting/chasing complete all as specified and directed. Make : Havells cat part no. INTEGRANEODLR24WLED857S or equvalent in make / manufacturers as given in Appendix 'B' to PS.

S&F in renewal of MCCB, 3 pole, 415 volt, 160 amp with breaking capacity 25KA and including connected accessories , spreader , terminal complete all as specified and directed.

S&F in repairs for LED domestic bulb 9 Watt type 240 volts complete all as specified and as directed.

S&F in repairs LED, luminaire surface mounted 300x300 mm,15 Watt, white powder coated CRCA housing with LEDs to provide glare free symmetrical illumination with white coloured flat acrylic cover. Make- Havells Cat pt no. PLUTOSURFACE1x1PLS15WLED857S or equivalent in make / manufacturers as given in Appendix 'B' to PS.

S&F in repairs LED, luminaire ultra modern recess mounted 600x600 mm, 34 Watt with high brightness white powder coated CRCA housing with LEDs Seamless front frame with white coloured flat acrylic cover complete all as specified and directed by Engineer-in-Charge (Make - Havells Cat part PLUNTONEO2X2PLR34WLED840S or equivalentin make / manufacturers as given in Appendix 'B' to PS.

S&F in replacement LED flood light luminaire 150 Watt ,energy saving,enviromental friendly, long life, exclusive innovative dei-cast aluminium IP65 with high power LEDs as light source complete all as specified and directed by Engineer-in-Charge. (Make - Havells Cat part JETAIRISFLS150WLED757PSYMLT G or equivalent in make / manufacturers as given in Appendix 'B' to PS.

S & F installation , testing and commissioning in repair of pressure die-cast aluminium housing with high power LED bldg security light fitting with IP-66 , 1x 120 Watt , fixed in position with and including 40 mm dia light grade GI Pipe made to shape not less then 1.2 Mtr long for mounting fitting with and including suitable size duly painted MS FI 40 x6mm clamps with nut and bolts , washers making electrical connection with and including three core 16/0.20 mm copper conductor flexible cable from connector to fitting complete all as specified and directed Make - Havells of Cat Part No ENDURAPEARLMAGSL 120WLED757 PASYTOTGASTHO equivalent in make / manufacturers as given in Appendix 'B' to PS.

S & F installation , testing and commissioning in repair of pressure die-cast aluminium housing with high power LED bldg security light fitting with IP-66 , 1x 45 Watt , fixed in position with and including 40 mm dia light grade GI Pipe made to shape not less then 1.2 Mtr long for mounting fitting with and including suitable size duly painted MS FI 40 x6mm clamps with nut and bolts , washers making electrical connection with and including three core 16/0.20 mm copper conductor flexible cable from connector to fitting complete all as specified and directed Make - Havells of Cat Part No ENDURAPEARLNEOSL45WLED 757PASYTOPC or equivalent model of Bajaj/ Crompton

S & F in replacement post top lantern LED light fitting for gate light 35 watt including all accessaries complete all as specified and directed. Make- Havells Cat Part No RUBYPT35WLED757PSYMTOPC or equivalent in make / manufacturers as given in Appendix 'B' to PS.

M & L in repairs Earthing complete with galvanished earth plate electrode of size 600 x 600 x 6.00 mm buried directly in ground (earth pit not less than 2.25 mtr below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4.00 mm dia as earthing lead by means of bolts, nuts, check nuts and galvanised iron or steel including earth work in any type of soil,PCC work in 1:3:6 pit and RCC 1:2:4 type B-1 pit cover reinforced with 6 mm dia ms bar 75 mm c/c 10 mm dia handle, charcoal salt 15cm alternate layer and around the earth plate as shown in electrical plate no 3 of SSR Part I 2010, 20 mm dia watering pipe medium grade 1.70 mtr long GI protection pipe light grade 15mm dia from earth pit to main board including necessary pit cover complete all as specified and as directed. (a) GI wire 4mm dia. (b) Watering pipe GI light grade 20mm dia from top of the earth electrode up to MS funnel with wire mesh embeded in floor of PCC earth pit. (GI Funnel should properly tightned on GI watering pipe and embeded in PCC floor of earth pit with open top suitable for watering of earth pits) (c) PCC earth pit 30x30x30cm internal dimension constructed in PCC 1:2:4 type B1 120 mm thick wall over PCC lean concrete foundation 500 mm x 500mm x 150mm thick, exposed surfaces of concrete smoothly finished with 15mm thick cement mortar (1:6) including RCC 1 :2:4 type B0 reinforced with 8mm dia deformed bars @100 mmc/c bothways pit cover 25mm thick with 2 Nos MS handles of 12mm dia suitable for carrying of pit cover. (d) Angle iron frame made of 40x40x4 mm for 30x30 cm PCC pit for holding the pit cover. (e ) Apply two coat of synthetic enamel paint over one coat of red oxide zinc chrome primer on exposed steel surfaces and two coat of hot tar on embedded portion of steel surfaces.

All as per ser item No. 172 here-in-before above but copper earth plate electrode of size 600x600x3.15 mm & copper strip 20x3mm as earth lead.

Supply and fixing of Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawm in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4.00mm dia galvanished iron or steel wire complete all as specified and directed. Note :- Rate also deemed to be includes necessary provision of excavation at site.

Supply and fixing of Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawm in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 20 X 3 mm copper strip complete all as specified and directed. Note :- Rate also deemed to be includes necessary provision of excavation at site.

Taking down carefully AC appliances fitted on roof of bldg and fixing temporary during water proofing treatment and after completion of water proofing work fixed the AC appliances to its original place including all necessary arrangement and material requried etc complete all as specified.

lodhi builders

M/s Himgiri construction