PROVISION OF EXTERNAL ELECTRICAL UPGRADATION WORK FOR PROVIDING ELECTRICITY AT HEMRL PUNE

Amount

Supply & installation of copper wound transformer 800 KVA step down, outdoor type complete with standard fittings, HT 22 KV 3 Phase, LT 433 volts, 3 Phase 4 wire with off load tappings on HT side to vary secondary voltage within limit, oil type distribution with OCTC as per BIS 1180 Level II & having minimum and equipped with the following: - a) Rating Terminal plate-01 No b) Earthing terminals-02 Nos c) Lifting lugs for transformer and tanks (minimum two) d) Off circuit tap switch-01 No e) Conservator with level indicator f) Oil filling hole with cap-01 g) Dehydrated silica jel breather-01 No h) Air release device-01 No j) Thermometer pocket-01 No k) Filter valve with blanking plate-01 No l) Explosion vent with diapharm-01 No m) Radiator n) Unidirectional flat rollers-04 Nos o) Separate neutral terminal -01 No p) Gas & oil relay with contact stem type dial thermometer-01 No q) Type of connection-Delta/ Star r) Cooling-ONAN s) Vector group-DYN 11 t) Temperature rise over an ambient of 50 degree centigrade maximum.

u) Cable end box HT side suitable for 22 KV, 95 sqmm 3 core cable v) Cable end box LT side suitable for LV Bus duct w) First fill of EHV grade Transformer oil complete all as specified and directed by Engineer-in-Charge. Make: ABB / Siemens / Bharat Bijlee / Crompton Greaves / Alstom (GEC) / BHEL.

Supply & installation of 22 KV outdoor switchgear panel consisting 1 No 22 KV 800A VCB breaker panel for Incomer & 1 No of 22 KV 800A VCB panel for outgoing and equipped with the following: - Incomer Panel a) 22 KV, 800A, 26.3KA for 3 sec VCB breaker, Type VD4/W/36KV closing, tripping coil - 110 V, DC spring charging motor 230vac - 01 No b) Resin cast PT dual core 22 KV / RT3 / 110V / RT3 / 110V / RT3 CL1.0 / CL 3P-50 VA - 03 Nos. c) Epoxy CT dual core -200A / 5A / 5A - 03 Nos CORE 1:200A/5A CL 1.0, 15VA CORE 2:200A/5A CL 5P10, 15VA d) Multifunction meter with RS 485 Port - 01 No. e) Voltmeter with VSS, 0.24 KV - 01 No. f) Protection relay 50, 51, 50N, 51N, 95 Numberical - 01 No. g) High speed tripping relay (86) VAJH 13, 110V DC - 01 No. h) 8 window annunciator, 110V, DC with hooter - 01 No. j) PUSH BUTTONS, TEST, ACCEPT & REST for ANNUNCIATOR - 03 Nos.

k) BCS (T-N-C) - 01 No. l) Local Remote S/w Lockable - 01 No. m) Control MCB - 04 Nos. n) Control Fuse Link - 12 Nos. o) 6 Sqmm terminals - 70 Nos. p) Indicating lamp R, Y, B ON / OFF / Trip / Trip Ckt Healthy + spring charged, test service - 11 Nos. q) 800A aluminium busbar 26 KA for 3 Sec - 01 No. r) Epoxy insulator - 09 Nos. s) MS fabrication outdoor - 01 No IP 4X size 1200 W MM x 2475 H MM x 2200 D MM t) Powder coating RAL 7032 - 01 No. u) Control wiring with 1100 volts grade multistranded copper conductor - 01 Job. v) Plated & high tensile hardware - 01 No. w) Glass epoxy barriers - 01 No. y) HT sleeves - 01 No. z) PVC channel - -1 LS aa) Insulated lugd - LS ab) Space heater - 02 Nos ac) Earthing bus 50 x 10mm, aluminium - 01 No. ad) Power pack 230 Vac / 110VDC, 5A - 01 No. ae) Sundry; 1 bolt, ferrules, markers, terminals, end clamp, end plate, name plate, stickers, tile, support, binding wire etc. - 01 No.

Outgoing Panel a) 22 KV, 800A, 26.3KA for 3 sec VCB breaker, type VD4/W/36KV closing, tripping coil - 110 VDC spring charging motor 230vac Nos - 01 No b) Epoxy C.T dual core - 75A / 5A / 5A - 03 Nos CORE 1:75A/5A CL 1.0, 15VA CORE 2:75A/5A CL 5P10, 15VA c) Multifunction meter with RS 485 Port - 01 No. d) Protection relay 50, 51, 50N, 51N, 95 Numberical - 01 No. e) High speed triping relay (86) VAJH 13, 110Vdc - 01 No. f) AUX relay for annunciation, 110VDC, VAA 33 - 03 Nos. g) 12 window annunciator, 110 Vdc with hooter - 01 No. h) PUSH BUTTONS, TEST, ACCEPT & REST for ANNUNCIATOR - 03 Nos. j) BCS (T-N-C) - 01 No. k) Local Remote S/w Lockable - 01 No. l) Control MCB - 05 Nos. m) Control Fuse Link - 12 Nos. n) 6 Sqmm terminals - 150 Nos. o) Indicating lamp R, Y, B ON / OFF / Trip / Trip Ckt Healthy + spring charged, test service - 11 Nos. p) 800A aluminium busbar 26 KA for 3 Sec - 01 No. q) Epoxy insulator - 09 Nos. r) MS fabrication outdoor - 01 No IP 5X size 2400 W MM x 2475 H MM x 2200 D MM

s) Powder coating RAL 7032 - 01 No. t) Control wiring with 1100 volts grade multistranded copper conductor - 01 Job. u) Plated & high tensile hardware - 01 No. v) Glass epoxy barriers - 01 No. w) HT sleeves - 01 No. x) PVC channel - -1 LS y) Insulated lugd - LS z) Space heater - 02 Nos aa) Earthing bus 50 x 10mm, aluminium - 01 No. ab) Sundry; 1 bolt, ferrules, markers, terminals, end clamp, end plate, name plate, stickers, tile, support, binding wire etc. - 01 No.

Rubber mat of 1 meter x 2 meter x 19 mm (for VCBs) complete all as specified and directed. Make: ISI Marked.

Supply, laying & testing cable XLPE earthed insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor, 22000 volts grade, of size 3 core 95 sq mm complete all as specified and directed. Make: HAVELLS / GLOSTER / KEI. Note: Necessary execavation and earthwork shall be measured and paid separately under relevant item.

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 400 sq mm 3.5 core complete all as specified and directed. Make: HAVELLS / GLOSTER / KEI. Note : Necessary execavation and earthwork shall be measured and paid separately under relevant item.

Supply, install & erect in true vertical position (or to be fixed in an inclined position as strut) pole steel tubular poles complete with MS base plate of 6 mm thick of size 300 mm x 300 mm, final taper plug, pole cap, bolts, nuts and washers and screws, pole made out of ERW MS tubing conforming to IS-2713 Part II, type 410-SP-55 (11.0 m long) HT poles including drilling of holes of required size and Nos for fixing of cross arm, painting with one coat of red oxide primer and two coats of aluminium paint for exposed surfaces and two coats of black bituminous paint for porton embeded in concrete, painting three black / red bands at lower portion of pole each of 300 mm height at 300 mm spacing, painting pole No with black paint at suitable height complete all as specified and directed by Engineer-in-Charge. Make: M/s Bombay Tubes / M/s Singh Profile / M/s India Electric Poles Mfg Co / M/s India Tubes Co.

S&F, switch air break gang operated triple pole mechanically operated from ground level, mounted on insulators and steel frame (9 polymer insulator type) outdoor type suitable for vertical installation single break provided with locking arrangement consisting of MS channel, HT post top insulator with operating rod 25mm bore GI pipe medium grade confirming to relevant IS, current rating 200 Amp and voltage 22 KV including jumpering, lead of wire / cable as directed at site. Make: Jaipuria Brothers / Pactil / Rashtriya. Note: Set of three measured as each unit.

S&F, HT 22 KV out door type drop out fuse double stack channel type suitable for horizontal or vertical mounting fixed type complete with 06 Nos polymer insulators and with earth switch upto 200 Amps complete all as specified and directed. Make: Jaipuria Brothers / Pactil / BHEL.

M&L for special factory made earthing electrode comprising of hot dipped galvanised steel pipe in pipe electrode, outer pipe 76mm dia medium grade and inner pipe 32mm dia including 3metre long and having 50 x 6mm terminal on inner pipe to connect earthign strip with 14mm dia holes for nut bolt buried directly and vertically in ground with top edge at 30cm below ground level after making bore hole of 100mm dia and 3.3metre deep using suitable mechanical drilling machine (for drilling near the specified bldg) connected with galvanised steel earthing lead of 32 x 6mm strip with minimum two Nos. of GI nut, bolts and connected to test point from earthing pit. The electrode pipes should be filled with 2 x 25 Kg bags of carbon based earthing compound. The compound shall be highly conductive, hygroscopic, non magnetic, non corrosive in nature and have best moisture retaining qualities with pH value between 7-9 connected to the earthing test point, fibre reinforced plastic pit not less 300 x 300mm with pit cover, including necessary returning, filling and removal of extra soil. Make: Fast electrode / U-PROTEC EARTHING PVT LTD / True power. Note: GI strip beyond 7.5mtr length shall be measured and paid separately.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr deep for taking out / laying of HT / LT under ground cable / HT pole and getting out in soft soil of earth strata complete all as specified and directed.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr deep for taking out / laying of HT / LT under ground cable / HT pole and getting out in hard soil of earth strata complete all as specified and directed.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr deep for taking out / laying of HT / LT under ground cable / HT pole and getting out in soft disintegrated rock of earth strata complete all as specified and directed.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr deep for taking out / laying of HT / LT under ground cable / HT pole and getting out in hard rock of earth strata complete all as specified and directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cm in soils complete all as specified and directed.

Removing surplus excavated soil to a distance not exceeding 50m depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M&L for dry crushed stone dust filling in trenches to required width at bottom and top of cable cushioning including spreading leveling and consolidation complete all as specified and directed. Note: Punned thickness shall only be measured and paid.

Supplying & laying un-reinforced precast concrete cable cover, class HV, type 1, flat, size 300mm x 180mm x 40mm complete all as specified and directed.

M&L for GI tube light grade with all fittings, complete, fixed to walls, pole ceiling or laid in trenches for cable protection all as specified for 100mm dia bore of pipe. Make: Jindal / TATA / Swastik. Note: Excavation and earth work where required shall be measured separately. MS clamps for fixing on wall / pole, etc are included in the unit rate.

M&L for GI tube light grade with all fittings, complete, fixed to walls, pole ceiling or laid in trenches for cable protection all as specified for 40mm dia bore of pipe. Make: Jindal / TATA / Swastik. Note: Excavation and earth work where required shall be measured separately. MS clamps for fixing on wall / pole, etc are included in the unit rate.

Cable joining kit for 22 KV (earthed) grade cable for outdoor termination heat shrink type joint complete with joining material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 95 sqmm complete all as specified and directed. Make: 3M Birla Ltd / Denson / M-seal.

Dismantling and taking down HT / LT OH line conductor and removing to store for safe custody or issue under schedule of credit complete all as specified and directed.

Dismantling cross arms / MS channel from HT pole including clamps, nuts, bolts & washers complete all as specified and directed.

Taking down insulators any type any description and removing to store for safe custody or issue under schedule of credit complete all as specified and directed.

Dismantling and taking down guarding wire and removing to store for safe custody or issue under Schedule of credit complete all as specified and directed.

Excavating in post holes in hard / dense soil (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface complete all as specified and directed.

Cement concrete in foundations, filling and mass concrete in type B2, 1:2:4 40 mm graded agreggate complete all as specified and directed.

M&L for joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming to Fe 290 (Gde E-165) complete all as specified and directed.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete drilled for fixing of steel sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to of Fe 410-W (Gde-E-250) quality-A complete all as specified and directed.

M&L for mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 10 cm long n exc 15 cm long complete all as specified and directed.

M&L for Preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed.

Supply only chain link MS galvanised fencing, any size or type complete all as specified and directed.

S&F, cable route indicators made of 3 mm thick MS plate and 100 mm dia fixed on MS angle 40 x 40 x 6 mm with a height of 60 cm above ground level and burried in ground grouted in PCC 1:3:6 of size 200 x 200 x 300 mm at a common interval of 100 mtrs complete all as specified and directed.

Supply, install, testing & commissioning, factory made and tested, CPRI approved LT panel board outdoor type, hood on top weather, vermin proof, free standing floor mounting type mounted on floor, cable alley for all the feeders, suitable for 440Volts, 3 Phase, 4wire, 50Hz AC supply system, conforming to IS, IP-56 class protection and made of 3.15 mm CRCA mild steel sheet with 50 x 50 x 6mm angle iron frame, hinged doors, front & rear opening and locking arrangement and duly powder coated on the outside and inside including necessary earthwork excavation and provision of PCC platform 100mm thick with PCC 1:3:6 type C-1 using 20mm graded stone aggregate over 250mm high brick platform, 15mm thick rendering in CM 1:6 to all exposed surfaces of brickwork, 100mm thick foundation in PCC 1:3:6 type C-1 using 20mm graded stone aggregate, 300mm all round the panel board, cable gland and lugs for incoming and outgoing cable etc., independent multilayer chambers to accommodate complete all as specified and directed including the following accessories:-

Incomer a) Bus bar chamber with electrolytic aluminium bus bar suitable for 1400 Amps capacity for 3 phase and neutral (all connection inside the panel shall be through aluminium strip) connected duly supported with FRP insulators including colour code heat shrinked insulating sleeves - 01 Set. b) Air Circuit Breaker 4 pole, 1250 Amps, microprocessor based manual draw out with overload short circuit, 415Volts, 50KA 50Hz - 01 No (Incoming). Out going a) MCCB, adjustable thermal and magnetic settings 415 volts, 4 pole, 400 Amps, 36 KA - 02 Nos. b) MCCB, adjustable thermal and magnetic settings 415 volts, 4 pole, 320 Amps, 25 KA - 02 Nos. c) MCCB, adjustable thermal and magnetic settings 415 volts, 4 pole, 200 Amps, 25 KA - 02 Nos.

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4.0 core complete all as specified and directed. Make: Havells / Gloster / KEI.

S&F, pole junction box sheet moulded compound (SMC) type with hinged door and locking arrangement of size 300 x 200 x 105 mm (internal) comprising one, one No SP MCB single pole of capacity 6 Amps, 240 volts and one No terminal for loop in & loop out suitable for three phase street light system including nuts, bolts and connecting up complete, 02 Nos MS clamp fabricated from 25 x 3mm MS flat iron complete all as specified and directed. Make: Sintex.

S&F in repairs suitable shape street light fitting bracket made out of GI pipe 40 mm dia med grade or of suitable size as per requirement and shape, 02 Nos of clamps made out from MS flat of size 40 mm x 6 mm with nuts and bolts (length of pipe should not less than 1.5 mtr) complete all as specified and directed.

S&F, new generation energy saving and environmental friendly long life LED street light 60 watt made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP Opening seperate driver compartment with IP-66 protection and impact resistance of IK07 on existing street light pole bracket complete all as specified and directed. Make: Havells / Crompton / Bajaj.

M&L for 3 single core PVC insulated unsheathed copper conductor cable multistranded 2 x 2.5 + 1 x 2.5 sq mm passing through in steel pole DB to street light luminaires complete all as specified and directed. Note: 3 runs of wire shall be measured as one length.

Dismantling and taking down street light fittings any type or capacity including brackets complete all as specified and directed.

S&F, Automatic Street Light Switch using NATURE SWITCH for automatic switching of Street Lights based on LUX level of Natural Light. The Sensor (Nature Switch) along with suitable Power Contactor, MCB and Support Terminals should be enclosed in pole / wall mountable Enclosure made of Rust Proof, Electric Shock Proof, Termite proof and FR grade special moulding compound (Sintex make SMC Junction box) conforming to IP-54. The Contactor, MCB and Circuit Wiring should suitable enough to take load of 12 kW load equally distributed over 3-phase. Contactor Rating: 40 Amps (4-pole). MCB (single-pole) Rating: 40 Amps (3 Nos.) Nature Switch: Kakatiya Energy Systems Pvt. Ltd. Hyderabad (EnC Approved) Contactor: BCH / L&T / Schneider or equivalent MCB: C&S / Schneider / Legrand / L&T. Make: SWADEEP - 02EC 12kW3P or equivalent.

M&L for PCC 1:4:8 using 20mm aggregate type D2 as in foundations, filling and mass concrete complete all as specified and directed.

M&L for brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

Rendering 15mm thick in CM (1:4) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

Hardcore of guage exc 63mm but n. exc 100mm deposited, spread and levelled in layers n exc 15cm thick, watered and rolled / rammed to a true surface complete all as specified and directed.

M&L for PCC (1:2:4) type B1 (using 20mm graded stone aggregate) as in floors and finished even and smooth complete all as specified and directed.

M&L for cutting of roads / plinth of Width-450 mm and depth-600 mm for removal / laying of pipe and making good the disturbed surfaces as per existing adjoining surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:2:4 type B1 by using 20mm graded crushed stone aggregate as in foundations of for making good road / foot path / hard standing / drain / building plinth protection complete all as specified and directed by Engineer-in-Charge.

Rough excavation not exceeding 1.5 metre deep and getting out in soft / loose soil complete all as specified and directed.

M&L for cross arms, bracings, supports, clamps and back plates fabricated from strucured steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one coat of red oxide and two coat of aluminium paint complete all as specified and directed.

M&L for Anti climbing devices; comprising 2.24mm dia galvanised steel 2-strand barbed wire with 2.00mm dia barbs wrapped spirally round poles, to a length of 0.5 to 1.0 metre clamped and properly secured or as ordered (clamps measured separately) complete all as specified and directed.

Danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps, bolts and nuts of approved size, for HT, 20 x 20cm size complete all as specified and directed.

M&L for indoor type end termination joint, heat shrinkable, type for under ground cable including joint kits and labour complete for making joints suitable for aluminium conductor cable XLPE, 3 core, 95 sqmm, 22 KV complete all as specified and directed by Engineer-in-Charge. Make: M seal / Denson / Capseal.

M&L for lightning arresters expulsion type complete with all fittings, transmission class, discharge capacity 65 kilo amp suitable for 22 kV complete all as specified and directed by Engineer-in-Charge.

M&L for straight through joint, heat shrinkable type for under ground cable including joint kit and labour complete for making joint suitable for aluminium conductor cable XLPE, 3 core, 95 sqmm, 22 KV complete all as specified and directed by Engineer-in-Charge. Make: M seal / Denson / Capseal.

Supply & lay in trenches un-reinforced precast concrete cable cover class LV type 1, flat size 250 x 150 x 40 mm for cable protection complete all as specified and directed by Engineer-in-Charge.

M&L for spreading stone aggregates / hardcore of gauge not exc. 20mm, deposited, spread and levelled in layers not exc. 15 cm thick including levelling and ramming to a true surface complete all as specified as directed by Engineer-in-Charge.

Excavation in trenches exc 1.50 m and n.exc 3.00 m deep and getting out in soft / disintegrated rock, complete all as specified and directed.

Excavation in trenches exc 1.50 m and n.exc 3.00 m deep and getting out in hard rock, complete all as specified and directed.

M&L for PCC 1:3:6 type C2 using 40mm graded aggregate as in foundations of stays and poles etc complete including necessary formwork weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for earth continuity conductor or main earthing lead fixed to poles or any other indicated situation for loop earthing as required 32 x 6mm size galvanised strip complete all as specified and directed.

SKS Electricals

United Sales Corporation

RAVINDRA BROTHERS

Rama Electricals