CA NO CWE BTD 27 of 2020-21 Special repairs to Bldg No P- 742 of MED Regt OTM 05 at Bathinda Mil Station under GE (North) Bathinda

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area not exc 1.5 Sqm each and removing from site including cutting holes for removal of hold fast complete.

S & F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as specified in Preamble 8B.3.1 of SSR Part -II (2010) and all as shown on drawing of SSR Part-II (2010).

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement all as per instruction and drawing shown for item No 8080 of SSR Part II.

S & F 100 mm long aluminium anodised, barrel tower bolts of extruded section.

S & F butt hinges, medium weight, cold rolled mild steel , size of hinges 100mm.

S & F 100mm extruded aluminium alloy handles, cast type, anodised.

S & F 100mm aluminium anodised hasp and stapple 100mm size

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm but not exc 4 Sqm each and removing from site including cutting holes for removal of hold fast complete.

S & F factory made pressed steel frames for door with one or more rebates including necessary fixing lugs, lock strike plate, hinges etc, compete, all as specified of frame size 105 mm x 60mm & thickness of MS sheet shall not be less than 1.25 mm including making holes for fixing hold fast etc and making good the wall with plaster in cement mortar (1:6) complete.

S & F factory made pressed steel frames for door with one or more rebates including necessary fixing lugs, lock strike plate, hinges etc, complete, all as specified of frame size 125 mm x 60mm & thickness of MS sheet shall not be less than 1.25 mm including making holes for fixing hold fast etc and making good the wall with plaster in cement mortar (1:6) complete.

M & L for PCC (1:3:6) type C-0 using 12.5 mm graded stone aggregate in filling in chowkats/ door frame or bed block of hold fast and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete.

M & L Second class Hard wood in timber scantling clean sawn including Dismantling timber scantling cross sectional area exceeding 40 Sqcm and over in section , in any position.

S & F Flush shutters 25mm thick solid core construction with block board core and plywood face panel, commercial type on both sides , chemically treated against termite infection complete all as specified.

S & F 35mm thick factory made panelled shutter (two panel) plain framed with lock rail and panel of 12mm thick veneered particle board with commercial veneering on both faces conforming to IS-3097 exterior grade kiln seasoned and chemically pressure treated of second class hard wood rails and styles and the size of rail and style as per IS-1003 (Part I).

S & F factory made glazed and skeleton shutters 35mm thick using second class hard wood open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc; sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24(a); all as specified complete.

S & F mild steel barrel tower bolts, stove enamelled black, with bright bolt, length of bolt 200mm.

S & F 125 mm mild steel pressed handles, oval type, stove enamelled black.

S & F mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, length of bolt 300mm.

S & F 300 mm long MS ordinary rat tail rod pattern springs for doors including roller and roller plate complete.

S & F mild steel galvanized wire cloth, 0.56 mm nominal dia of wire & average width of aperture 1.18mm and fixed with galvanized steel wire staples complete.

S & F in repairs mild steel galvanized wire cloth, 0.56 mm nominal dia of wire & average width of aperture 1.18mm and fixed with galvanized steel wire staples complete.

S & F factory made steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded including one shop coat painting including dismantling of old existing window as directed.

S & F factory made fixed type steel ventilator with top hung without glazing bar complete including dismantling of old existing window/ ventilator as directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins / spring clips of size not exceeding 0.5 Sqm each pane complete.

S & F sheet glass, 4 mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane fixed with oil putty or wooden beads including Provn of glazing pins/spring clips wherever necessary.

S & F figured pin headed glass, 4 mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane fixed with oil putty or wooden beads including Provn of glazing pins/spring clips wherever necessary.

M & L for painting to new steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces.

M & L for painting to new wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces.

S & F in repairs vitreous china squatting pan, 'Orissa' pattern, size 580mm x 440mm, white, with integral foot rests including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. including making good to floor and excluding flushing cistern, flush pipe and waste pipe complete.

S & F in repairs PVC valveless, syphonic action type, flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle including brackets and PVC flushing pipe 32mm dia complete.

S & F kitchen or laboratory sinks with drainage board made of stainless steel 1 mm thick fixed with plugs, washers; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete.

M & L for granite stone work Udaypur Green (table rubbed and polished) 18 to 20 mm thick in cooking platform and like laid in CM 1:4 including pointing in white cement in 1:2 using marble dust with admixture of pigment to match the shade of the slab including rubbing and mirror polishing laid over and including 15 mm thick Screed bed or bedding layer in CM (1:4) complete.

Dismantling stone slab and tiles of any description or thickness in floor , apron etc , laid bedded and pointed in any mortar as directed.

S & F in repairs, PVC connections 15 mm bore, 450 mm length, heavy duty, with PTMT nuts.

S & F in repairs brass chromium plated shower rose 125 mm size with or without swivel joints fix to steel pipe or union complete all as specified and as directed.

S & F in repairs stop valves, chromium plated, fancy type, quarter turn, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions for 15 mm bore dia of pipe.

S & F in repairs, 15 mm bore chromium plated, fancy type, quarter turn, bib taps cast copper alloy with crutch or butterfly handle, screwed for iron pipe, or for brass ferrule complete all as specified and as directed.

M & L for 15 mm bore GI pipe, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors including taking up or down 15 mm bore existing steel tubing and connections complete.

Taking up or down 15 mm bore existing steel tubing and connections complete and re-fixing the same in new or old position to walls and ceilings or laid in floors including cleaning of pipe and provision of new fitting as required complete all as directed.

M & L for 20 mm bore GI pipe, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors including taking up or down 20 mm bore existing steel tubing and connections complete.

Taking up or down 20 mm bore existing steel tubing and connections complete and re-fixing the same in new or old position to walls and ceilings or laid in floors including cleaning of pipe and provision of new fitting as required complete all as directed.

M & L for non skid coloured ceramic tiles of size minimum 400mm x 400mm, 7 to 8 mm thick (square/rectangular), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile with including 15 mm thick Screed bed or bedding layer in CM (1:6) including dismantling existing floor tiling including cement mortar bedding and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified. Note: Only course sand shall be used in screed bed.

S & F glazed ceramic coloured tiles 450 x 350mm, 7 to 8mm thick in verticle surfaces such as dado / skirting, set and jointed in neat cement slurry and pointed in white or coloured cement pigmented to the match the shade of tiles laid over and including 10 mm thick rendering in cement mortar (1:4) as backing coat and finish the surface rough to receive the tile including dismantling existing hearth or wall tiling including cement mortar bedding (but not backing) etc on brick or stone walls etc including racking out joints hacking for key and scrubbing removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified.

M & L for machine cut kota stone slab flooring minimum size 450 mm x 450 mm, 18 to 20 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing laid over and including 20 mm thick Screed bed or bedding layer in CM (1:6) complete.

All as per item No 44 above but in vertical surfaces such as steps , riser , skirting , dado and pillars as directed at site including 10 mm thick rendering as backing coat in cement mortar (1:4) all as directed.

S & F PVC (SWR) 110mm bore pipes, single socketed, in any length with rubber ring joints, fixed to walls with and including MS clamps including taking down existing eaves gutters and rain water pipes (any size or pattern ), including all fittings, heads, shoes, bends, swan necks, etc. (measured overall as fixed along the center line over fittings and accessories)

S & F 110 mm bore PVC (SWR) bends of any radius / shoe, fixed to PVC pipes as directed.

S & F grating doom 140mm dia of PTMT (minimum weight 50 gm) for floor trap.

S & F in repairs 75 mm dia cast iron floor trap with chromium plated grating incluing jointing to waste pipe fixed in cement concrete (1:2:4) type B-1, complete all as specified.

S & F 100 mm bore cast iron (spun) soil, waste and vent pipes, ISI marked in any length with or without ears, with cement joints, laid in trenches or in floor or fixed to walls with and including suitable size clamps including dismantling of existing drain pipes, jointed in cement mortar all as directed.

S & F 75 mm bore cast iron (spun) soil, waste and vent pipes, ISI marked in any length with or without ears, with cement joints, laid in trenches or in floor or fixed to walls with and including suitable size clamps including dismantling of existing drain pipes, jointed in cement mortar all as directed.

S & F in repairs 100 mm bore cast iron bends (any radius), diminishing pieces or tapers (large bore measured) .

S & F in repairs 75 mm bore cast iron bends (any radius), diminishing pieces or tapers (large bore measured) .

S & F SGSW Gully trap of size 150 x 150 mm, set and jointed to drain in CM 1:1 complete all as specified.

S & F aluminium anodised snap grid frame work 605mm x 605mm for false ceiling comprising of main / cross tee / wall angle weighing not less than 0.36 Kg/RM to be fixed to ceiling with 6mm dia GI wire supporting hanger upto 1200mm length adjusting level fixed to roof slab at 600 mm c/c by means of 'J' bolt with necessary bolt , nuts and washers or expansion hold fasteners 12.5mm dia and 40 mm long as per manufaturer's instruction including M & L for 12 mm tapered edge gypsum board of size 600 x 600mm (conforming to IS-2095-1982) shall be screw fixed to ceiling section with 25 mm dry wall screws at 230 mm centre to centre , screw fixing shall be done mechanically either with screw driver or drilling machine with suitable attachment and finally the boards shall be jointed and finished so as to have a flush look including dismantling of old false ceiling of any type / any size complete all as specified.

M & L for rendering 15 mm thick in cement mortar (1:6) on internal wall surfaces of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement including taking down old cement plaster including raking out joints hacking for key scrubbing down with water etc and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified.

M & L for rendering 15 mm thick in cement mortar (1:4) on external wall surfaces of brick work or concrete surfaces even and fair without using extra cement mixed with liquid water proofing material as per manufacturer's instruction including taking down old cement plaster including raking out joints hacking for key scrubbing down with water etc and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified. (NOTE – WP material shall be measured and paid for separately.)

M & L for rendering 5 mm thick in cement mortar in (1:3) finishing the surfaces even and smooth on ceiling including taking down old cement plaster and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified.

M & L for preparing newly plastered surfaces of walls and applying three coats of white wash all as specified..

M & L for preparation of newly plastered surfaces of external walls and apply Two coats of weather coat Apex paint (External emulsion) of approved tint by using airless spray / roller over and including a coat of acylic external primer all as specified. Note :- Contractor may use manual tools for surface preparation with prior approval of Engg- in- charge in writing in case use of mechanical equipments are not possible.

M & L for preparing newly plastered surfaces of ceiling and applying three coats of white wash all as specified.

M & L for Brick work using old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar (1:6), including demolition of old brickwork or stone masonry of any type.

M & L for rendering 5 mm thick in cement mortar in (1:3) over 10 mm thick in cement mortar (1:4) as additional / floating coat on concrete surfaces of walls , chajjah , beams , ceiling etc even and smooth without using extra cement mixed with liquid water proofing material as per manufacturer's instruction including taking down old cement plaster and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified. (WPC shall be measured and paid for separately.)

M & L for RCC (1:2:4) type B1 using 20 mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies and in shelves and the like, finished exposed surface fair and even including demolition of existing RCC of any description. (Note - Reinforcement and form work shall be measured and paid separately)

M & L for precast cement concrete (1:2:4) type B1 using 20mm graded stone aggregate as in manhole cover, slabs of any thickness / kerb stone etc, size or shape including necessary form work and set in CM (1:4) including demolition of existing RCC Cover slab of any description complete all as specified. (Note - Reinforcement and form work shall be measured and paid separately)

M & L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

Demolition of brick tiles or terracing tiles, single layer on roofs including removing the demolished material exceeding 1 km and not exceeding 2 km away from site and disposal off in low lying area as directed.

Demolition of mud in roof, any thickness including plastering and leaping (where full thickness recovered or only a part there of) including removing the demolished material not exceeding 200 m away from site and disposal off in low lying area complete.

M & L for cleaning of top surfaces of concrete roof slab , lime terracing , or surface of tiles with wire brush including flashing and junction of parapets etc and surface painting with layer of blown grade bitumen of any penetration applied hot @ 1.70 Kg / Sqm and rendering in 15 mm thick in cement mortar (1:4) mixed with liquid water proofing material as per manufacturer's instruction , priming the surface @ 0.30 Kg / Sqm and laying 3 mm thick APP based polymer membrane of weighing not less than 3 Kg / Sqm reinforced with polyster non woven fabric (Weight not less than 150 Gm / Sqm) laid on primed surface by torch application , side overlap 75mm and end overlap 100mm and tucked into chases as a treatment for moderate condition complete all as specified and as directed.

M&L providing 80 mm thick lime concrete or cement concrete in (1:3:6) type C2 using 40 mm graded stone aggregates as leveling course on roof slab.

Material and labour for 40 mm thick brick tiles laid on mud mortar or CM (1:6), 20 mm thick and joints grouted flush in CM (1:3) mixed with @ 5% of crude oil by weight of cement or mud phuska complete all as specified.

All as per item No. 81 but except brick tiles complete all as specified. Note :- Old serviceable brick tile to be reused after cleaning and washing.

S & F 1000 litres capacity Rotational moulded polyethylene in white colour, three layered, water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of old water tank of any size and any type and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc all as directed.

S & F in repairs ball valves high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe of size 20 mm bore (minimum weight 210 gram).

S & F in repairs Gun metal globe or Gate valve , with iron wheel , screwed both ends for iron pipe or for unions for 20 mm bore dia of pipe.

Complete removal of existing treatment on wall (any number of layers) by scrapping with steel wire brushes or any other means, including filling depressions of scrapped surfaces and M & L for preparation of old plastered surfaces of walls and applying the following:- (i) Two coats of weather coat Apex paint (External emulsion) of approved tint by using airless spray / roller over and including a coat of acylic external primer. Note :- Contractor may use manual tools for surface preparation with prior approval of Engg- in- charge in writing in case use of mechanical equipments are not possible.

Supply only liquid water proofing material, ISI marked.

Internal Electrification

Taking down carefully existing unserviceable copper / aluminum point wiring (light, fan, socket) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, light fittings etc and removing the retrieved materials from site including making good the disturbed surface of walls, floors, ceilings etc to match with the adjoining work complete all as specified and directed.

M & L for point wiring with multi stranded copper conductor FRLSH cable, 1100 volts grade PVC insulated and unsheathed of size 1.5 Sqmm single core in existing PVC concealed conduit and including new MS sunken box and 3 mm thick bakelite laminated sheet top cover for one fan / light / exhaust fan controlled by one switch including provision of 1.5 Sqmm PVC insulated unsheathed with single core, multi stranded copper conductor FRLSH cable as earth wire to common earth & connecting to earth dolly all as specified and directed.

All as per item No 80 here in before but for socket outlet 5 pin, 6 Amp on same board complete all as specified.

All as per item No 80 here in before but for socket outlet 5 pin, 6 Amp on independent board but not below the switch board complete all as specified .

All as per item No 80 here in before but for one socket outlet 6 pin, 6/16 Amp multipurpose 2 in 1 on independent board with cable of 2.5 Sq mm, multi stranded copper conductor FRLSH cable including provision of 2.5 Sq mm PVC insulated solid copper conductor FRLSH cable continues as earth wire connected to earth dolly, conductor etc.

M & L for point wiring with multi stranded copper conductor FRLSH cable, 1100 volts grade PVC insulated and unsheathed of size 1.5 Sqmm single core in and including PVC concealed conduit not less than 20mm dia (medium duty ISI marked) and conduit fittings with and including 3 mm thick bakelite laminated sheet top cover for one fan / light / exhaust fan controlled by one switch including provision of 1.5 Sqmm PVC insulated & unsheathed with single core, multi stranded copper conductor FRLSH cable as earth wire to common earth & connecting to earth dolly all as specified and directed.

All as per item No 84 here in before but for socket outlet 5 pin, 6 Amp on same board complete all as specified.

All as per item No 84 here in before but for socket outlet 5 pin, 6 Amp on independent board but not below the switch board complete all as specified .

All as per item No 84 here in before but for one socket outlet 6 pin, 6/16 Amp multipurpose 2 in 1 on independent board with cable of 2.5 Sq mm, multi stranded copper conductor FRLSH cable including provision of 2.5 Sq mm PVC insulated solid copper conductor FRLSH cable continues as earth wire connected to earth dolly, conductor etc.

S & F Switch semi modular , flush type, single pole, one way, 5/6 Amp .

S & F Switch semi modular with frame, flush type, single pole, one way, 15/ 16 Amp .

S & F Semi modular socket, multipurpose, 2 in 1, 5 Pin, 6 Amp, flush type, including decorative frame cover. (Note: Switch and socket shall be of same make.)

S & F Semi modular socket outlet universal, multipurpose, 2 in 1, 3 Pin 6 Amp and 6 pin 16 Amp, flush type, including decorative frame cover. (Note: Switch and socket shall be of same make.)

S&F, fan regulator electronic step type (1-5), socket type 230-240 Volt, AC supply, complete all as specified and directed.

S & F ceiling rose, 3 plate, surface bakelite type, Polycorbonate body, 6 Amps, 250 Volts AC, 65 x 50 mm, three terminal (ISI marked) complete all as specified.

S & F Lamp holder of PVC/Polycarbonate type with back plate suitable for batten fitting including 9 watt LED bulb.

S & F MCCB, TPN, 125 Amps, breaking capacity 25 KA thermal magnetic based including taking down old unserviceable MCCB TPN complete all as specified.

S & F MCB, SPN, 40 Amps, 'C' curve , 230 Volts, 50 Hz, breaking capacity not less than 10 KA with over load and short circuit protection and including taking down old unserviceable MCB complete all as specified.

S & F MCB, SP, 6 to 40Amps, 'C' curve, 230 Volts, breaking capacity not less than 10 KA with over load and short circuit protection including taking down old unserviceable MCB SP complete all as specified.

S & F sheet metal enclosures double door made out of CRCA mild steel sheet, concealed, surface mounting, acrylic door, IP-43 protection, 12 way, DB SPN 230 Volts, with 200 Amp rated bus bar, dust and vermin proof suitable for fixing MCB's and Isolators etc including taking down old unserviceable DB.

S & F sheet metal enclosures double door made out of CRCA mild steel sheet, flush mounted, acrylic door, IP-43 protection, 4 way, DB VTPN 415 Volts, with 200 Amp rated bus bar, dust and vermin proof suitable for fixing MCCBs , MCB's and Isolators etc including taking down old unserviceable DB.

M & L for sub main wiring with 2 single core cable PVC insulated unsheathed of copper multi strandard conductor FRLSH cable of size 6 sqmm, 1100 votls grade drawing through in and including PVC concealed conduit 20 mm dia medium duty including accessories such as Tee, bend, Elbow etc, ISI marked with and including PVC insulated 6 sqmm unsheathed multistranded FRLSH copper conductor cable for earth continuity and connected to common earth dolly including cutting chasing of wall, if required and making good disturbed surface in CM (1:3) and finishig the surface to match with existing surface etc including taking down old unserviceable wiring 6 Sqmm complete all as specified. Note:- Two runs of cable, one run of earth wire and one run of PVC conduit shall be measured as one unit.

S & F 18/20 watt Retro LED tube light fitting, wall/surface mounted, IP 20 protection, conforming to IS 16106/IS 16107, minimum 6000K batten decorative type 4 feet long polycarbonate body, white, in built LED driver, power factor>0.95 , Make – all as per Crompton Cat Part No. DMLN1LT8-16 (for batten) and Cat part No. LT8-20-865-2 (for tube light) including 18/20 watt tube rod or equivalent model of any make given in Appx 'B' connecting to electric point by using PVC insulated twin core copper conductor cable of suitable size including taking down old existing light fitting all as directed.

S & F energy efficient LED street light fitting of 25 Watt with PDC aluminium body and clear glass with lens for wide beam distribution, top maintainable type with IP 66 degree of protection, PF > 0.95 with voltage range 140 to 270 Volt, fitting should be provided with inbuilt 5 KV minimum surge protection, short circuit and over voltage protection facility for Driver and fitting including 25 watt LED lamp with GI brackrt - 01 No, MS clamp-02 Nos suitable for walls/ columns and making electrical connection with providing of 1.50 metre long twin core round copper conductor cable of suitable size and testing complete all as per SYSKA cat part No. SSK-SLF-CF-25W-WL or equivalent model of any make given in Appx 'B', Cat Part No. as approved by GE complete all as specified including taking down old unserviceable existing street light fitting of any type and capacity from pole along with accessories.

M/s PANKAJ KUMAR

M/s Kamal Builders

M/s HANS BROTHERS

R K GOYAL & COMPANY

M/s MITTAL CONSTRUCTIONS

RINKU BROTHERS

M/s GURFATEH BUILDERS

M/s Bhullar Constructions

M/S VERMA BUILDERS & DEVELOPERS