Construction of Office Building for Raipur Chapter of The Institute of Company Secretaries of India (ICSI) at Raipur (CG)

Grand Total (DSR+ Non DSR):- 2,94,18,530

BILL OF QUANTITIES

S.No. DESCRIPTION OF ITEM UNIT TOTAL QTY RATE Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas

(exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal

of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers

2 2.25 not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto Cum 165.00 190.71 31,466.82

50m and for all lift.

Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto

3 2.25a a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in cum 75.00 681.59 51,118.99

foundation trenches, plinth, sides offoundation etc. complete for all lift.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and

dressing complete.

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20

mm nominal size derived from natural sources)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and

6 4.1.8 shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural cum 30.00 6,628.08 1,98,842.28

sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced

cement concrete work; using coarse aggregate and fine aggregate derived from natural sources,

Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions

as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without

impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but

7 5.33 excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-

in-charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable

separately. In case the cement content in design mix is more than 1.10 times of the specified minimum

cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra

5.33.1 All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum cum 85.00 9,248.12 7,86,090.35

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced

cement concrete work; using coarse aggregate and fine aggregate derived from natural sources,

Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions

as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without

impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but

8 5.33 excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-

in-charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable

separately. In case the cement content in design mix is more than 1.10 times of the specified minimum

cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra

All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content

9 5.9 Centering and shuttering including strutting, propping etc. and removal of form for :

5.9.1 Foundations, footings, bases of columns, etc. for mass concrete sqm 70.00 381.56 26,709.34

5.9.2 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. sqm 100.00 819.75 81,975.25

5.9.3 Suspended floors, roofs, landings, balconies and access platform sqm 537.89 902.21 4,85,292.02

5.9.4 Shelves (Cast in situ) sqm 50.00 902.21 45,110.71

5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers sqm 530.77 716.52 3,80,305.83

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts sqm 445.46 935.34 4,16,658.74

5.9.16.1 Edges of slabs and breaks in floors and walls Under 20 cm wide metre 190.20 202.92 38,595.22

5.9.19 Weather shade, Chajjas, corbels etc., including edges sqm 50.00 925.42 46,271.02

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation

and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure

11 6.4.2 above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse cum 6.00 8,860.09 53,160.54

Brick work with clay flyash F.P.S. (non modular) brick of class designation 7.5 in superstructure above

plinth level up to floor five level in :

12 6.32.2 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 145.00 8,849.48 12,83,175.13

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using

14 4.13 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with sqm 12.83 142.20 1,824.48

apiece of cloth lightly soaked in kerosene oil.

Digitally signed by PRIYA

Construction of Officie Building for the Institute of Company Secretaries of India (ICSI) at Raipur (CG)

BILL OF QUANTITIES

S.No. DESCRIPTION OF ITEM UNIT TOTAL QTY RATE Amount

15 2.34 Supplying chemical emulsion in sealed containers including delivery as specified.

2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% litre 95.60 228.41 21,836.16

Diluting and injecting chemical emulsion for Pre-CONSTRUCTIONAL anti-termite treatment (excluding

the cost of chemical emulsion) :

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart

2.35.3 including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse

sand) to match the existing floor :

15 2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration sqm 172.10 301.68 51,918.90

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and

16 5.22.A.6 binding all complete upto plinth level & above plinth level. Thermo-Mechanically Treated bars of grade KG 36,330.72 104.94 38,12,474.91

Fe-500D or more.

21 Aluminium Work

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built

up standard tubular sections/appropriate Z sections and other sections of approved make conforming to

IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the

gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc.

17 21.1 Aluminium sections shall be smooth, rust free,straight, mitred and jointed mechanically wherever

required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel

screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing,

paneling and dash fasteners to be paid for separately) :

21.1.1 For Fixed Portion

18 21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) kg 300.00 516.57 1,54,969.71

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making

21.1.2 provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket

required (Fittings shall be paid for separately)

19 21.1.2.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) kg 300.00 617.32 1,85,195.96

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with

20 21.3 EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of

Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

21 21.3.2 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm) Sqm 50.00 1,464.61 73,230.41

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought

22 9.1.2 framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast cum 1.22 1,13,374.25 1,38,316.59

lugs or dash fastener shall be paid for separately).

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core

of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering

with vertical grains or cross bands and face veneers on both faces of shutters.Providing and fixing ISI

23 9.5.1.1 marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board SQM 49.35 3,380.06 1,66,805.77

construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical

grains or cross bands and face veneers on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and

manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring

type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as

per direction of Engineer in charge (Door handle, lock and stopper etc. to be paid separately)

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush

door shutters (over all area of door shutter to be measured).

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting,

fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc.,

including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the

same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary

26 10.26 accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the kg 342.00 751.55 2,57,028.46

floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for

payment purpose only weight of stainless steel members shall be considered excluding fixing

accessories such as nuts, bolts, fasteners

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede

27 9.127.1 finish with high density protective surface layer and reverse side of adhesive bonding quality conforming sqm 106.26 1,017.71 1,08,141.80

to IS : 2046 Type S, including cost of adhesive of approved quality

Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts,

28 9.5.3 nuts and wooden plugs and embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement Nos. 100.00 222.67 22,267.11

: 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than

29 9.96.1 grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. sqm 25.00 295.06 7,376.56

complete : 300x16 mm

Digitally signed by PRIYA

Construction of Officie Building for the Institute of Company Secretaries of India (ICSI) at Raipur (CG)

BILL OF QUANTITIES

S.No. DESCRIPTION OF ITEM UNIT TOTAL QTY RATE Amount

Providing and fixing aluminium tower bolts, ISI marked, powder coated (minimum thickness of powder

30 9.97 coating 50 micron) transparent or dyed to required colour or shade, with necessary screws etc.

complete : 250x10 mm.

Providing and fixing aluminium handles, ISI marked, powder coated (minimum thickness of powder

31 9.100.1 coating 50 micron) transparent or dyed to required colour or shade, with necessary screws etc. sqm 50.00 64.46 3,223.06

complete :125 mm.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not

32 9.101.2 less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary each 25.00 70.40 1,759.91

screws etc. complete. Twin rubber stopper

Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient

acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76

litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the

33 22.22A ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete sqm 172.10 547.90 94,292.95

application/system not less than 500 microns). The operation shall be carried out after scrapping and

properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per

the direction of Engineer-in-Charge.

34 13.4.2 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) sqm 1,002.84 334.37 3,35,319.73

35 13.5 15 mm cement plaster on the rough side of single or half brick wall of mix :

Cement concrete flooring 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a

36 11.3.1 floating coat of neat cement, including cement sluny, but excluding the cost of nosing of steps etc. sqm 119.00 597.62 71,116.38

complete. 40 mm thick with 20 mm nominal size stone aggregate

Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8 mm

having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours

and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20 mm

thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting

the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer)

with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and

38 11.41A shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement

slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc.,

11.41A.1.1 Double Charge Size of Tile 800 x 1600mm sqm 240.12 1,511.51 3,62,943.02

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer)

with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and

39 11.41A shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement

slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc.,

11.41A.3.2 Glazed Vitrified tiles Matt/Antiskid finish of size 600 x 1200mm sqm 48.33 1,748.77 84,518.19

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as

curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick

stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and

jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching

shade including rubbing, curing and polishing etc. all complete as specified and as directed by the

Engineer-in-Charge.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine

cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,

approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse

sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including

rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be

specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green,

42 8.31 black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm sqm 171.15 1,233.72 2,11,150.38

thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg

per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6

graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal

size, well rammed and consolidated and grouted with fine sand, including necessary excavation,

levelling & dressing & finishing the top smooth.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50

44 13.41 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even

shade and colour :

Digitally signed by PRIYA

Construction of Officie Building for the Institute of Company Secretaries of India (ICSI) at Raipur (CG)

BILL OF QUANTITIES

S.No. DESCRIPTION OF ITEM UNIT TOTAL QTY RATE Amount

New work (two or more coats) over and including water thinnable priming coat with cement primer

having VOC content less than 50 gram/litre

Providing &Applying high quality acrylic modified resin based texture of Dholpur/Red sand stone Pattern

with anti algae and UV resistance properties to be applied as intermediate finish in desired pattern @

43.04 kgs/10 sqm to form film of 1- 1.5 mm thickness after scrapping and properly cleaning the surface

to remove loose particles from the plaster surface, followed by top coating with PremiumAcrylic Smooth

exterior paint with Silicone additives of required shade by two or more coats @ 1.43 litres/10 sqm,

complete as the direction of Engineer -in-Charge.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and

manufacturer, over the plastered wall surface to prepare the surface even and smooth Complete.

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with

SS screws etc .complete as per direction of Engineer-in-Charge.

47 21.12.2 Powder coated minimum thickness 50 micron aluminium tubular handle bar NOS. 4.00 614.50 2,457.99

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level,

suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/

sqm, both side inclusive) consisting of main 'T runner with suitably spaced joints to get required length

and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center

and cross ·r of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between

main "T" at 600 mm center to center to fonn a grid of 1200x600 mm and secondary cross "T" of length

600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the

12.52 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false

ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like

diffusers, grills, light fittings, fixtures, smoke detectors etc. Main ~" runners to be suspended from

ceiling using GI slotted cleats of size 27 x 37 x 25 x1 .6 mm fixed to ceiling with 12.5 mm dia and 50 mm

long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8

mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections

shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and

as directed by Engineer-in-charge.

GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick

with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro

statically polyester powder coated of thickness 60 microns (minimum), including factory painted after

12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming

to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center

borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side,

having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing.

Providing and supplying aluminium extruded tubular and other aluminium sections as per the

architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6

as per BS 1474,including super durable powder coating of 60-80 microns conforming toAAMA2604 of

50 25.1 required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material KG 1,296.00 403.11 5,22,435.61

such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing

extra shall be paid on this account). The weight of aluminium extruded section shall be taken for

purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of

structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights

and all levels, including: (a) Structural analysis & design and preparation of shop drawings for the

specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times

design wind pressure without any failure), including functional design of the aluminum sections for

fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets,

screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop

(barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation &

drainage and protection against fire hazard including:

(b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium

alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to

accommodate 3 Dimentional movement for achieving perfect verticality and

25.2 fixing structural glazing system rigidly to the RCC/ masonry/structural steel SQM 136.00 3,415.72 4,64,537.44

framework of building structure using stainless steel anchor fasteners/ bolts,

nylon seperator to prevent bimetallic contacts with nuts and washers etc. of

stainless steel grade 316, of the required capacity and in required numbers.

(c) Providing and filling, two part pump filled, structural silicone sealant and

one part weather silicone sealant compatible with the structural silicone sealant

of required bite size in a clean and controlled factory / work shop environment,

including double sided spacer tape, setting blocks and backer rod, all of

approved grade, brand and manufacture, as per the approved sealant design,

within and all around the perimeter for holding glass.

(d) Providing and fixing in position flashings of solid aluminium sheet 1 mm

thick and of sizes, shapes and profiles, as required as per the site conditions,

to seal the gap between the building structure and all its interfaces with curtain

glazing to make it watertight.

Digitally signed by PRIYA

Construction of Officie Building for the Institute of Company Secretaries of India (ICSI) at Raipur (CG)

BILL OF QUANTITIES

S.No. DESCRIPTION OF ITEM UNIT TOTAL QTY RATE Amount

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6

mm insulated glass (double glazed) vision panel units of size and shape as required and specified,

comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with

reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear

float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal

(structural silicone sealant) etc. all complete for the required performances, as per the Architectural

drawings, as per the approved shop drawings, as specified and as

directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass

(Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment,

only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and

weather silicone

sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm

thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear

Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light

reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U

value of 3.0 to 3.3 W/ m2 degree K etc. The properties of performance glass shall be decided by

technical sanctioning authority as per the site requirement

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all

accessories and hardwares for the openable panels as specified and of the approved make such as heavy

duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles,

buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete

as per theArchitectural drawings, as per the approved shop drawings, as specified and as directed by the

Engineer- inCharge.

Digitally signed by PRIYA

Summary of Cost

Construction of Officie Building for the Institute of Company Secretaries of India (ICSI) at Raipur (CG)

S.No. Description DSR-2022 Amount Market Based Amount

1 Cost of Internal Electrification & LAN Work 16,08,440.08 4,23,091.00

2 Cost of Fire Detection & Alarm Work 2,57,783.64 -

3 Cost of CCTV Surveillance Work 17,105.10 89,074.32

4 Cost of EPABX & Networking Work 19,528.88 78,484.55

5 Cost of Sub Station Equipment Work

6 Subhead-I HT Work 1,22,157.44 3,46,799.34

7 Subhead-II Transformer - 1,68,439.00

8 Subhead-III Distribution Panel - 5,34,906.00

9 Subhead-IV L.T Cable Work 99,795.47 4,40,100.00

10 Subhead-V Earthing Work 2,19,669.24 -

11 Subhead-VI Cable Tray Work 16,372.60 -

12 Subhead-VII DG Set - 6,24,108.00

13 Subhead-VIII On Grid Solar Power Backup System 6,43,310.70 -

14 Uninterrupted Power Supply - 4,61,772.00

15 AV System for Conference Hall 72,468.61 14,64,367.83

16 VRV Based HVAC System Work - 27,67,523.70

17 Access Control System 22,151.65 18,500.00

18 Illuminated Signages 15,600.00

19 Cost of Fire Fighting Work 3,13,838.37 1,74,430.48

20 Plumbing Work

a Internal Plumbing Work 4,84,000.49 16,500.00

b External Plumbing Work 2,16,194.00 -

21 Tubewell 2,98,122.50

Digitally signed by PRIYA

Construction of Officie Building for the Institute of Company Secretaries of India (ICSI) at Raipur (CG)

Sr.No. Sch.No. Particulars Unit Qty Rate DSR Amount Non-DSR Rate

A Internal Electrification & LAN Work

Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

single core cable in surface / recessed medium class PVC

1 1.10.3 conduit, with modular switch, modular plate, suitable GI box Nos. 110.00 1,545.59 1,70,014.90 -

and earthing the point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable etc. as required.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface /

recessed medium class PVC conduit, 2 way modular switch,

modular plate, suitable GI box and earthing the point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable

etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC

insulated copper conductor single core cable in surface/

recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated

copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the

4 1.14 following sizes of FRLS PVC insulated copper conductor, single core cable in -

surface/ recessed medium class PVC conduit as required.

Supplying and drawing following pair 0.5 mm dia FRLS PVC

insulated annealed copper conductor, unarmored telephone

cable in the existing surface/ recessed steel/ PVC conduit as

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper

6 1.19 conductor PE insulated, shielded with fine tinned copper braid and protected with Meter 50.00 49.52 2,476.00 -

PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of recessed

conduit as required.

Supplying and fixing following modular switch/ socket on the

8 1.24 existing modular plate & switch box including connections but -

excluding modular plate etc. as required.

a 1.24.6 Telephone socket outlet Each 9.00 155.93 1,403.37 -

b 1.24.7 TV socket outlet Each 1.00 155.93 155.93 -

c MR RJ45 socket cat 6 with shutter Each 11.00 502.00 5,522.00

Supplying and fixing two module stepped type electronic fan

9 1.25 regulator on the existing modular plate switch box including Each 18.00 388.77 6,997.86 -

connections but excluding modular plate etc. as required.

Supplying and fixing following size/ modules, GI box alongwith

10 1.27 modular base & cover plate for modular switches in recess etc. -

Supplying and fixing suitable size GI box with modular plate and cover in front on

11 1.31 surface or in recess, including providing and fixing 3 pin 5/6 A modular socket Each 18.00 502.55 9,045.90 -

outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on

12 1.32 surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular Each 31.00 617.39 19,139.09 -

socket outlet and 15/16 A modular switch, connections etc. as required.

Installation ,Testing, Commissioning of wall bracket /ceiling

13 1.35 fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, Each 105.00 125.38 13,164.90 -

complete with all accessories including connections etc. as required.

Supplying and fixing stiff pendent with 300 mm long, 20 mm dia X 1.6 mm thick

steel conduit, aluminium cast back plate and brass holder complete, including

wiring the down rod with 1.5 sq. mm FRLS PVC insulated, copper conductor, single

core cable and painting etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase,

230 V, complete as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/

recessed Steel/ PVC conduit as required.

Wiring for group controlled (looped) light point/fan

point/exhaust fan point/ call bell point ( without independent

switch etc.) with 1.5 sq. mm FRLS PVC insulated copper

conductor single core cable in surface/ recessed PVC conduit,

and earthing the point with 1.5 sq. mm FRLS PVC insulated

copper conductor single core cable etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on

surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular

socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For

light plugs to be used in non residential buildings).

Supplying & fixing suitable size GI box wih modular plate and

cover in front on surface or in recess including providing and

fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including

connections, painting etc. as required.

Digitally signed by PRIYA

Sr.No. Sch.No. Particulars Unit Qty Rate DSR Amount Non-DSR Rate

Supplying and fixing following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415 V, on

surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without

MCB/RCCB/Isolator)

c 2.4.1 8 way (4 + 24), Double door Each - -

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature

circuit breaker suitable for inductive load of following poles in the existing MCB DB

connections, testing and commissioning etc. as required.

c 2.10.5 Three Phase & Neutral Each 5.00 1,293.79 6,468.95 -

Supplying and fixing following rating, double pole, (single phase

and neutral), 240 V, residual current circuit breaker (RCCB),

22 2.14 having a sensitivity current 30 mA in the existing MCB DB -

complete with connections, testing and commissioning etc. as

Supplying and fixing 63Amp, four pole, (three phase

and neutral), 415 volts, residual current circuit breaker (RCCB),

23 MR having a sensitivity current 300 mA in the existing MCB DB Each 1.00 6,087.00 6,087.00

complete with connections, testing and commissioning etc. as

required. Similar to Legrand or equivalent.

Supplying and fixing 40/63A rating, 415 V, 10 kA, "C" curve, miniature circuit

breaker suitable for inductive load of Four poles in the existing MCB DB complete

with connections, testing and commissioning etc. as required. Similar to Legrand

DX3 AC MCBs or equivalent.

Supplying and installing following size of perforated painted

with powder coating M.S. cable trays with perforation not more than 17.5%, in

convenient sections, joined with connectors, suspended from the ceiling with M.S.

suspenders including bolts & nuts, painting suspenders etc as required.

a 4.1.1 100 mm width X 50 mm depth X 1.6 mm thickness Each 50.00 572.09 28,604.50 -

b 4.1.4 300 mm width X 50 mm depth X 1.6 mm thickness Each 10.00 818.63 8,186.30 -

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe of

2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm

thick including accessories, and providing masonry enclosure

with cover plate having locking arrangement and watering pipe

of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre

below ground as strip earth electrode, including connection/

28 5.9 terminating with G.I. nut, bolt, spring, washer etc. as required. Meter 60.00 151.71 9,102.60 -

(Jointing shall be done by overlapping and with 2 sets of G.I. nut

bolt & spring washer spaced at 50mm)

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre

below ground as strip earth electrode, including connection/

29 5.8 terminating with nut, bolt, spring, washer etc. as required. Meter 35.00 1,024.07 35,842.45 -

(Jointing shall be done by overlapping and with 2 sets of brass

nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I.

30 5.1 pipe from earth electrode including connection with brass nut, Meter 35.00 1,634.09 57,193.15 -

bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.

31 5.11 pipe from earth electrode including connection with G.I. nut, Meter 35.00 743.82 26,033.70 -

bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in

recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess

33 5.18 for loop earthing along with existing surface/ recessed conduit/ Meter 35.00 44.25 1,548.75 -

submain wiring/ cable as required.

LED Down lighter (SMD Type) (System lumen efficacy >135 lm/Watt)

Supplying, installation, Testing & Commissioning of LED Recessed /

surface Down lighter (Round /square/Rectangular) SMD type of following body

material with PMMA and prismatic diffuser and construction as per IS : 10322 with

driver as per the requirement with Driver efficiency >85%, Operating voltage AC

140-270 Volt, freq 50/60 hz, Operating temp range - 15 deg to 40 deg centigrade,

internal surge protection of 2.5 KV with Short & Open circuit protection ,THD <

10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free, (flicker

should be below 5 %), life time (LED,Driver & electrical circuitry), life time of

minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends

as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /

6000°K /6500°K (As per ANSI Bin) , SDCM(Standard Deviation Color Matching) <3,

Maximum power consumption should not more than the specified rating and

Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.).

Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on

housing. OEM must have its own in house NABL lab setup for all testing facilities

for LED fixtures. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC

insulated copper conductor single core cable and earthing etc. as required

Digitally signed by PRIYA

Sr.No. Sch.No. Particulars Unit Qty Rate DSR Amount Non-DSR Rate

with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output

. LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures

as per BIS shall be submitted. Shape size and CCT shall be as approved by - -

Engineer-in-Charge as per requirement. (Thermal management: heat sink of

aluminum housing such that LED junction temperature shall not rise above 90°C).

Powder coated die cast / Extruded aluminum Body including trim. - -

SITC of 12W Extruded aluminium batten available in 2ft run length with multiple

lumen packages and suitable for surface, wall & conduit ounting (with

accessories). similar to Philips Type HSN Code MRP (INR) BN 021 LED12S 6500 PSU

GR or equivalent.

Supply and fixing of water tight oblong 10 Watt LED bulkhead luminaire having

pressure diecast housing with driver set confirming to IP 65 and above Protection,

IK08, High purity / transmisivity UV stablized Non yellowish diffuser/ Reflector for

uniform light distribution, ditachable driver set, suitable for 24hrs continuous

operation complete in all respect.

1200 system lumen, >120lm/W, PF>0.95, CRI>70, >300V, over voltage protection,

4KV internal surge protection with 5 year warrenty. CAT-AAA

LED Batten light (System lumen efficacy >135 lm/Watt)

Supplying, installation, Testing & Commissioning of LED surface mounted

Batten light of following body material and construction as per IS : 10322 with

driver (Replaceable) as per the requirement with Driver efficiency >85%

,Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range -

15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short &

Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80 , Flicker

free (flicker should be below 5 %), life time (LED,Driver & electrical circuitry),

of minimum 50000 Burning Hours with , 70% of initial Lumen

maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6000°K/

6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching)

<3, Maximum power consumption should not more than the specified rating - -

and Fixture shall be of relevant BIS standard and trade mark certificate (

T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen

printing on housing. OEM must have its own in house NABL lab setup for

all testing facilities for LED fixtures. complete in all respect i/c

connections with 1.5 sq mm FRLS, PVC insulated copper conductor

single core cable and earthing etc. as required with Minimum 5 year OEM

warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test

report from NABL lab for all testing required for LED fixtures as per BIS

shall be submitted. Shape size and CCT shall be as approved by Engineerin-

Charge as per requirement. (Thermal management: heat sink of

aluminum housing such that LED junction temperature shall not rise above

Powder coated die cast /Extruded aluminum Body (Thickness ≥ 1.20

LED Panel light 2x2 ft., (System lumen efficacy >135 lm/Watt)

Supplying, installation, Testing & Commissioning of Panel light 2x2 ft., of

following body material and construction as per IS : 10322 with driver as per the

requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, freq

50/60 hz, Operating temp range -15 deg to 40 deg

centigrade, internal surge protection of 2.5 KV with Short & Open circuit

protection,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare

Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED,Driver &

electrical circuitry), of minimum 50000 Burning Hours with , 70% of initial Lumen

maintained till life ends ,CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per

MR ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power - -

consumption should not more than the specified rating and Fixture shall be of

relevant BIS standard and trade mark certificate (T.C.). Manufactures Word Mark/

Name Engraved/ Embossing/Screen printing on housing. complete in all respect i/c

connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core

cable and earthing etc. as required with Minimum 5 year OEM warranty. System

lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report from NABL lab for

all testing required for LED fixtures as per BIS shall be submitted. Shape size and

CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal

management: heat sink of aluminum housing such that LED junction temperature

shall not rise above 90°C).

Brush Less Direct Current (BLDC) Motor

Supply, Installation, Testing and Commissioning of ceiling fan with Brush

Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal

(Aluminum alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety

rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value

(CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD

42 MR (Total Harmonic Distortion) less than 10%, remote (preferably mobile app based) Each 18.00 - 2,381.00 42,858.00

for speed control and all remaining

accessories including safety pin, nut bolts, washers, temperature rise=75

degree C (max.), insulation resistance more than 2 mega ohm, suitable for

230 V, 50 Hz, single phase AC Ceiling Fan compliant to IS 374:2019 fan

Supply, earthing etc. complete as req

1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min

Supply Installation Testing and Commissioning of 300mm sweep 1500RPM energy

efficient exhaust fan.

Lightning Arrestor Work - -

Digitally signed by PRIYA

Sr.No. Sch.No. Particulars Unit Qty Rate DSR Amount Non-DSR Rate

Lightning Arrestor: Supply, installation, testing and commissioning of External

Lightning wide area protection system based on Eaarly Streamer Emission (ESE)

technology. Device shall emit electromagnetic impulse in the form of a streamer

into the air microseconds earlier than naturally formed streamers. Device confirmg

to NFC 17-102 and UNE 21186 Standards. Appropriate non penetrating mounting

arrangement. The device shall be mounted at suitable clear to the highest point on

the roof top. (Model selected shall give coverage of 79 M radius @ min 5M height

Down conductor:Supply, installation, testing and commissioning of 70 Sqmm

46 MR twisted 19-Strand, bare Cu cable on surface/wall / as per site requirement and Metre 40.00 - 2,127.90 85,116.00

complete in all respect.

Lightning Counter :Supply and installation of counting the number of lightning

strikes without any power supply.

49 MR Test Link :Supply and installation of test link in weather proof IP 65 BOX. Each 3.00 - 2,400.00 7,200.00

Supply, installation, testing and commisioning of 2 x 25W LED Aviation abstruction

light medium bay type 62, complete with lamp, lamp holder, Condenser necessary

50 MR connecting wire, 1 X 25 AV with all necessary hardware, accessories as required for Each 1.00 - 10,406.00 10,406.00

complete installation. Rate shall include the cost of necessary steel structures ,

fixing arrangements in this item. Refer drawing.

Total Internal Electrification & LAN Work (A):- 16,08,440.08 4,23,091.00

B Fire Alarm System :

Supplying, installation, testing & commissioning of main

control and indicating panel made out of 16 SWG MS sheet

to accommodate the following items duly powder coated in

approved colour with louvers for ventilation, locking

arrangement, audio and visual indication for fire alarm and

public address system, monitoring system including

connections, interconnections etc complete as required.

10 Zone panel for fire alarm system

250 Watt amplifier racks suitable for operation on 230V

AC/24V DC supply conforming to IEC-268-3 complete with all

accessories as required - 2 Nos.(one to act as standby)

Talk back master station with LED PTT (press to talk) push

1 17.1.10 button for operation on 230V AC/24 V DC supply conforming NOS 1.00 74,159.84 74,159.84

to IEC-268 for simplex mode of operation/communication

suitable for 20 Nos.talk back unit -1 set.

Annoucement control desk suitable for selection of different

zones selectively and ON ALL CALL switch with visual

indication etc. complete as required -1 set.

Amplifier change over switch for inter changing amplifier -1 No.

Monitor panel for loudspeaker complete with output

selector, ON/OFF switch, fuse, visual indications etc.

complete as required- 1 No.

Gooseneck microphone with stand and ON/OFF switch- 1 No.

Main ON/OFF switch, fuse indication lamps, DC and AC

voltmeters & ammeters, terminal blocks etc. complete as

required -1 set. -

Supplying, installation, testing & commissioning of smoke

2 17.1.2 detector with builtin LED and mounting base complete with all NOS 20.00 1,214.77 24,295.36

connections etc. as required.

Supplying, installation, testing & commissioning of heat

detector operating at 54ºC/57ºC with rate of rise cum fixed

temperature (dual thermistor) type with mounting base

complete with all connection etc. as required.

Supplying, installation, testing & commissioning of addressable fire control module

complete as required.

Supplying, installation, testing & commissioning of manual call

boxes of MS construction in surface/recess with stainless steel

chain & hammer assembly complete with glass and push button

etc. as required.

Supplying, installation, testing & commissioning fire alarm

sounder with facility to make announcement, mounted in M.S.

7 17.1.6 box (16 SWG) with hinged cover plate & suitable for operation NOS 3.00 586.84 1,760.52

with amplifier i/c line matching transformer etc. complete as

Supplying, installation, testing & commissioning of fire fighter telephone handset

complete as required.

Supplying, installation, testing & commissioning talk back slave

station in surface/recess suitable for operation on simplex

9 17.1.8 mode complete with P.T.T. knob & speaker/microphone NOS 3.00 953.48 2,860.45

enclosed in a M.S.(16 SWG)/ ABS box with break glass in front

etc. complete as required.

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated

with annealed copper conductor having glass mica fire barrier tape covered by an

10 17.5.1 extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and metre 305.00 378.23 1,15,360.80

LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as

C CCTV Surveillance Work

Digitally signed by PRIYA

Sr.No. Sch.No. Particulars Unit Qty Rate DSR Amount Non-DSR Rate

DSR 2022 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/

1.54 recessed Steel/ PVC conduit as required.

Supplying, installing, testing and commissioning of 8 port CAT6 jack panel loaded

as per the connections required in jack panel.

Supplying, installing, testing and commissioning of I/O(Information outlet ) for

CAT6 Cable termination

Supplying, installing, testing and commissioning of 6 U wall mount rack with fans ,

2 cable managers , satationary shelf , 2 Nos of hardware pkts.

Supply, Installation, Testing & Commissioning of CCTV Client Operator Station with

MR 1 No.of 55” LED Display - Complete as per specifications & preferred make. Make: Nos 1.00 27,375.00 27,375.00

SONY/Samsung/LG

MR Supplying, installing, testing and commissioning of HDMI to HDMI Cable. Nos 1.00 1,206.82 1,206.82

MR Supply installation testing and commissioning of 3m Cat-6 patch cord. Nos 7.00 807.50 5,652.50

Supplying and fixing of following sizes of medium class PVC conduit along with

1.21.2 accessories in surface/recess including cutting the wall and making good the same Meter 70.00 160.95 11,266.50 - -

in case of recessed conduit as required. 25mm Dia

Supplying and laying of following size DWC HDPE pipe ISI marked along with all

accessories like socket, bend, couplers etc. conforming to IS 14930, Part II

14.15.1 complete with fitting and cutting, jointing etc. in the existing trench, complete as Meter 10.00 140.97 1,409.70 - -

63 mm dia (OD-63 mm & ID-51 mm nominal)

SITC of 2 MP IR Fixed Dome Network Camera -1/2.7″ Progressive Scan CMOS, 1920

× 1080 at 25fps, 2.8 mm Fixed lens, 0.002 Lux at F1.4, 0 Lux with IR on, ICR, ONVIF

(PROFILE S, PROFILE G, PROFILE T), support H.265, H.264, MJPEG, 120db WDR, 3D

MR Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR 1.00 - 4,200.00 4,200.00

range: 40m, Support on-board storage up to 256 GB (SD card not included), IP67,

Edge Analytics- Line crossing detection, Intrusion detection, Motion detection,

Video tampering, UL, CE, FCC certified.

SITC of 2 MP IR Fixed Bullet Network Camera -1/2.7″ Progressive Scan CMOS, 1920

× 1080 at 25fps, 2.8 mm Fixed lens, 0.002 Lux at F1.4, 0 Lux with IR on, ICR, ONVIF

(PROFILE S, PROFILE G, PROFILE T), support H.265, H.264, MJPEG, 120db WDR, 3D

MR Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR 2.00 - - 6,650.00 13,300.00

range: 40m, Support on-board storage up to 256 GB (SD card not included), IP67,

Edge Analytics- Line crossing detection, Intrusion detection, Motion detection,

Video tampering, UL, CE, FCC certified.

SITC of 8 channel Network Video StoragE NVR suitabe to access data from any

remote location including backup drive for 30days.

D EPABX SYSTEM

SITC of IP-PBX WITH REDUNDANT CPU & REDUNDANT POWER SUPPLY 16 CO

TRUNK, 20 ANALOG EXTENSION, 2 SIP TRUNK, PMS INTEGRATION

2 MR SITC OF BASIC PHONE WITH CLI Nos 1.00 1,600.00 1,600.00

3 MR S/f of I/O Boxes Krone connectors ,with connection etc. -

6 MR Wiring of Jelly Filled telephone Cable in existing pipe for system with connection. -

Supplying and laying of following size DWC HDPE pipe ISI marked along with all

accessories like socket, bend, couplers etc.

conforming to IS 14930, Part II complete with fitting and cutting,

jointing etc. in the existing trench, complete as required. 100mm Dia

5 MR SITC of 2m long Cat-6 patch cord as required Nos 11.00 250.00 2,750.00

S/I/T/C of 24 port category 6e SL Series fully loaded patch Panel Make Dlink/Amp

with active and passive components,punching, complete in all respect

Supply, Installation, Testing & Commissioning of Access Enterprise PoE Network

24 Port10/100/1000 Base-T Non PoE switch.

Supplying, installing, testing and commissioning of 6 U wall mount rack with fans ,

2 cable managers , satationary shelf , 2 Nos of hardware pkts.

9 MR Mapping of Network Nodes & LAN Diagram Job 1.00 15,000.00 15,000.00

Total amount (D) 19,528.88 78,484.55

Total amount (D) 19,528.88 78,484.55

E External Electrical

A Subhead-I HT Work

1 11 KV DOUBLE POLE STRUCTURE

Supply, erection, testing and commissioning of 2 pole structure for providing 1 No.

MR 11KV,200A GOS in accordance with IE rules, & local authority specification and Set 1.00 - 82,000.00 82,000.00

drawings and comprising of the following.

a. 2 Nos. 11 mtr. long MS STEEL poles complete with, pole excavation, MS STEEL

foundation, and back filling complete MS steel channel/angle iron etc.

b. 1 Set of cross arms, branching, clamps and painting complete with GI nut, bolts

& washers as required (for GO & DO), LA connection.

c .1 set 11KV Insulator complete with spindles & hardware complete as required.

d .1 No. 11KV 400A TP Gang operated Air break switches complete with 25mm dia

GI pipe operating machanism, handle & locking arrangement.

e. 1 set of 3 nos.11KV single pole drop out fuse complete with barrel fuses, and

mounting arrangement.

f. 1 set (3 nos.) 11KV lightning arrestor and connecting to all phases.

g. 4 No. 150 mm dia 6 meter long GI pipe class 'B' (for XLPE cable protection) as

h. 2 Set 50mm dia 3m long GI pipe earting with 25 x 6 mm GI earth strip complete

as required (for GO & DO & LA)

i 1 nos. 11KV HT danger boards and 2 set of anticlimbing devices.

11 KV Double Pole Structure described below

Supply of 3 core standered aluminium conductor XLPE (Cross linked polyethylene)

2 insulated PVC bedded, Galvanised flat steel strip armoured cables confirming to

I.S. 7098 (Part-II with latest amendments) II KV grade as per requirement.

Digitally signed by PRIYA

Sr.No. Sch.No. Particulars Unit Qty Rate DSR Amount Non-DSR Rate

DSR 2022 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11

8.3 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

8.3.2 Above 120 sq. mm and upto 400 sq. mm Meter 40.00 141.18 5,647.20

supplying and making indoor cable end termination with heat

DSR 2022 shrinkable jointing kit complete with all accessories including lugs suitable for

10.4 following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as

Supplying and making outdoor cable end termination with heat shrinkable jointing

7 kit complete with all accessories including lugs suitable for following size of 3 core,

XLPE aluminium conductor cable of 11 KV grade as required :

Supply and laying of 1800mm x 900mm x 12mm thick chequered rubbbber matting

of tested quality.

Supply and fixing of shock treatment chart (prescribed under I.E. rules) duly

9 MR framed with glass and supported from back with hard board or soft board with Each 1.00 247.98 247.98

supply of all material labour T&P for proper completion of work.

Supply and fixing of C02 type fire extinguisher 4.5 kg. capacity (ISI Marked IS :

10 MR 2878 & TAC approved) complete with initial charge and wall bracket, along with Each 1.00 14,043.93 14,043.93

supply of all materials and labour for proper completion of work.

Supply and laying of PVC Insulated, FRLS Round Sheathed Multi Core Industrial

11 Flexible Cable conforming to IS 694:2010 with Flexible Bright Annealed Copper

Conductor for Voltage Grade 1100 Volts as per direction of engineer incharge.

Total For Subhead-I HT Work 1,22,157.44 3,46,799.34

B Subhead-II Transformer

11/0.433 KV, 3 Phase, 50 Hz outdoor/ indoor mounting(Mineral oil filled) Supply,

installation, testing and commissioning of following capacity (continuous loading)

BEE 3 Star rated (Corresponding Level as per BIS

amended upto date of receipt of tender) , 11/0.433 KV step down, 3 Phase, 50 Hz,

Dyn 11 vector group, ONAN (Oil Natural Air Natural) copper wound transformer

(Electrolytic grade 99.9% pure copper, Core made of first grade Cold Rolled Grain

Oriented (CRGO) Core grade MOH or better, suitable for out door/indoor

applications with On Load Tap Changer (OLTC) on HV side having AVR relay and

Remote Tap Changer Control (RTCC) for automatic sensing of incoming voltage,

automatic operation of OLTC and facility for remote and manual operation of OLTC

HV side in range of +5% to-15% in steps of 2.5%, having cable end boxes on HV

side suitable for 3x300 sqmm XLPE cable of 11 KV grade, including bus trunking

arrangement on LV side including supplying and laying of copper conductor

multicore control cable from transformer to HT breaker/panel for safety tripping,

complete with all accessories and safety provisions as per relevant

IS Code including first filling of filtered dehydrated oil, i/c supplying and grouting of

suitable M.S. Channel with all accessories and transformer shall be confirming to IS

: 2026 (Part 1 to Part 5), IS : 1180 and duly ISI Marked and as per CPWD

specifications complete in all respects etc as required at site. The maximum flux

density in any part of the core and yoke at rated voltage and frequency shall be

such that the flux density with + 12.5 percent combined voltage and frequency

variation from rated voltage and frequency

does not exceed 1.9 Tesla. The permissible temperature-rise shall not

exceed 35 dg.C for oil and 40 dg. C up to 200 KVA and 40 dg.C for oil and 45

dg. C for above 200 KVA for winding. Inside of tank shall be painted with

varnish or liquid resistant paint. For external surfaces one coat of thermo

setting powder paint or one coat of epoxy primer followed by two coats of

polyurethane base paint shallbe used. IS: 1180 (Part 3) shall be referred to

for paint thickness for normal to medium corrosive atmosphere. For highly

polluted atmosphere and special application external paint work shall be as

per direction of Engineer-in-Charge. Design ambient condition : a) air

temperature 50 deg C, b) Relative Humidity 90 % Max, c) Seismic Zone as

per location of site, d) Altitude as per location/site. Noise level Shall not

exceed limits as per NEMA TR-1 with all accessories running measured as

per IEC 551 / NEMA standard. The transformer should have QR code which

should contain drawing, test report OEM manual,Geo - Tag of manufacturing

location etc. Marking Each transformer shall be provided with rating plate

made of anodized aluminum/ stainless steel material securely fixed on the

outer body, easily accessible,as per IS: 1180 Part-3. The entries on the rating

plate shall be indelibly marked.

Digitally signed by PRIYA

Sr.No. Sch.No. Particulars Unit Qty Rate DSR Amount Non-DSR Rate

Fitting and Accessories : The following fittings shall be provided:- a) Two

earthing terminals with the earthing symbol b) Oil level gauge indicating oil

level at minimum, 30°C and maximum operating temperature; c) Air release

device (for non-sealed type transformers) d) Rating and terminal marking

plates; e) Silica gel breather f) Drain-cum-sampling valve (¾″ nominal size

thread, IS 554) preferably steel with plug for three phase transformers; g)

Thermometer pocket with cap; h) Oil filling holes having (1¼″ nominal size

thread) with cover (for sealed type transformers without conservator); i)

Lifting lugs for the complete transformer as well as for core and winding

assembly; j) Pressure relief device or explosion vent above 200 kVA; k) One

filter valve on the upper side of the tank (for transformers above 200 kVA); l)

Unidirectional flat rollers (for transformers above 200 kVA); m) Inspection

hole (for transformers above 200 kVA); n) HV side neutral grounding strip

(where one of the HV bushing terminal is connected to earth);

o) Buchholz relay for transformers above 800 kVA. p) Arcing horns or

suitable rating lightning arrestors for HT side – 3 Nos. q) Bird guard; r) Oil

temperature indicator and winding temperature indicators for transformers

above 200 kVA with suitable tripping mechanism above permissible limit s)

Jacking pads (for transformer above 1 600 kVA); t) Additional Neutral

DSR 2025 separately brought out on bushing for earthing. u) Magnetic oil level gauge

3.10 (for transformer above 1600 kVA) with low oil level alarm contact; v) Non

return valve (for conducting pressure test); w) Pressure relief device or

explosion vent x). Monogram Plate y) Inspection cover z). Detachable type

radiators with top and bottom shutoff valve. aa) Oil Conservator with Oil level

indicator, minimum level marking and drain plug for all transformers of

capacity 50 KVA and above. bb) Necessary hardware, clamps, lugs etc. for

termination on HV/MV etc. for all transformers.

Total For Subhead-II Transformer 1,68,439.00

C Subhead-III Distribution Panel

SITC of LT switchgear panels suitable for 433 V, 3 phase, 4 wire, 50 Hz power

distribution system. The panel shall be Indoor, free standing, floor mounting, sheet

metal clad, cubicle, dead front, dust and vermin proof type compartmentalised

design fabricated out of 14 SWG CRCA sheet steel, complete with colour coded,

heat shrinkable PVC insulated, aluminium bus bars and separate earth bus bar of

adequate cross section through out the length of the panel. The incoming and

outgoing feeders shall be accommodated in a fully segregated, modular multitier

arrangement with adequate size and distinct cable alley, bus bar alley/chamber.

The panel shall be complete with name plate, earthing, numbering, danger plate

etc. as per specifications and drawings as required. The panel shall withstand the

fault level of 50kA as per Single Line Diagram. The Panel shall also be capable to

communicate status like ON/OFF/ Trip through Modbus/Ethernet for major

component like ACB, MCCB, MCB & Multifunation meters.

The Main LT Panel shall use all draw out type breakers suitable for 415 V AC, 3

phase, 50 Hz, 3 phase 4 wire supply system. Panel shall have Buscoupler switching,

auto operation of incommer and bus coupler, auto start of D.G. Sets, auto D.G.

running by pre set timing, auto changeover etc and having following incomming

and outgoing Air Circuit Breakers,microprocessor release for overload, short

circuit, instantaneous & earthfault protection with Current & Voltage metering &

Air Circuit Breaker with microprocessor release ge metering & LCD display , with

ready to clsoe indicator, should have capability to communicate ON /OFF/ Trip

Status on Modbus/Ethernet and as per the detail specification of ACB

(Icu=Ics=Icw=65 KA (1 sec). MCCB, with microprocessor release with LSIG

protection functionand should not derate upto 50 decree Centrigrate as per

testing guideline as per IEC 60947-2 and all the ACB upto 2500Amp ACB should

have same frame size LCD display for fault trip history, haivng current limiting

feature, double break mechanism & capability to communicate ON /OFF/ Trip

Status on Modbus/Ethernet. (16 KA Ics)

1 Nos. 200 Amp FP MCCB 16KA

R,Y,B Phase indication Lamp with control MCB

On, Off, Trip Status Indication with control MCB

Inbuilt Zone Slelective Interlocking function

Multifunction Meter

1 Nos. 100 Amp FP MCCB 16KA

R,Y,B Phase indication Lamp with control MCB

On, Off, Trip Status Indication with control MCB

Inbuilt Zone Slelective Interlocking function

Multifunction Meter

Reverse Power Relay

Power Conditioning Device

1 Nos. 63 Amp FP MCCB 16KA (10KWp Solar Power)

R,Y,B Phase indication Lamp with control MCB

On, Off, Trip Status Indication with control MCB

Inbuilt Zone Slelective Interlocking function

Multifunction Meter

Reverse Power Relay

Power Conditioning Device

1 Nos. 100Amp FP ATS

1 Nos. 250 Amp FP busbars of aluminium alloy as per SLD.

1 Nos. 125 Amp FP busbars of aluminium alloy as per SLD.

Digitally signed by PRIYA

Sr.No. Sch.No. Particulars Unit Qty Rate DSR Amount Non-DSR Rate

1 Nos. 63 Amp TP MDO MCCB 16 KA, having specs as per attached annexture

R,Y,B Phase indication Lamp with control MCB

On, Off, Trip Status Indication with control MCB

5 Nos. 63 Amp FP MCCB 16 KA

On, Off, Trip Status Indication with control MCB

Multifunction Meter

EX LIGHT + LIFT + Pl+ Spare + UPS +Spare

5 Nos. 63 Amp FP MCB 16 KA

On, Off, Trip Status Indication with control MCB

PDB+HVACDB +Spare

5 Nos. 32 Amp FP MCB 16 KA

On, Off, Trip Status Indication with control MCB

Short Circuit Breaking capacity should not less than 50KA.

RELAYS AS PER SLD

53 50KVAR APFC PANEL TTA

HYBRID Power Factor Correction System

Supply, Installation, testing and commissioning of HYBRID APFC Panel, 3

phase 4 wire, 415 V, 50 Hz AC System for Ambient temperature -5°C to

+40°C of following capacity with passive solution of 60% capacity and active

solution of 40% capacity,3Phase 4 wire Hybrid Power Factor Correction

Solution (with arrangment for neutral current balance) to achieve >0.99 lag

and TDDI/THDV values within IEEE recommended limits.APFC should be

designed as per IS 16636 Or IEC 61921. The active section and passive

section shall work in sync to give optimized output. The degree of protection

of passive section should be IP 42, and of active section should be minimum

IP 21.The switching device for APFC passive section should be through

capacitor duty contactor and for the active compensation system shall be

IGBT based with 3 level topology having 12 IGBT in inverter circuit. The

active compensation system should filter harmonics from 2nd to 50th

individual harmonic order and shall be selectable for the entire range. The

active compensation system should have feature to improve PF correction

and harmonic filtration having response time <25Micro second. The hybrid

panel shall be indoor type floor mounted free standing totally enclosed,

extensible, fabricated in compartmentalised designed made of CRCA sheet

steel of 2.0mm thick for framework & covers, 3 mm thick for gland plate i/c

cleaning & finishing complete with 9 tank process for powder coated of

approved shade ( RAL 7032-Siemens gray or as approved by Engineer-in-

Charge), having front section (switch gear and control accessories) and rear

section (capacitor and reactor), front and rear access, having suitable

current carrying capacity, extensible TPN Aluminium alloy bus bar of high

conductivity, DMC/SMC bus bar supports,bottom base channel of MS

Section, fabrication shall be done in transportable section, entire panel shall

have common copper earth bar of minimum size of 25mm x 5mm with 2

nos. earth studs, the earth terminals provided on the body of capacitor bank

shall also be bonded to the main capacitor panel earth bus with 2 nos. 8

SWG or 6 SWG GI earth wires/ equivalent size of copper conductor cable,

forced ventilation for maintaining temperature rise not more than 5°C from

ambient, interconnections, connections with 14% detuned reactor and

heavy duty 525 V ISI marked Impregnated MPP(Metalized Polypropylene)

Capacitor (IS 13340 Part -1 & 2) APFC Panel shall be in compliance with IS

:16636 & CPWD Specifications etc. as per below details.

Suitable capacity MCCB Microprocessor base with O/C, S/C, E/L release of

TPN 50KA breaking capacity (Ics=Icu), ON, OFF, Trip, R, Y, B - LED

Indicating Lamp set along with required Instruments and accessories with

extended rotary handle and door interlocking arrangement. Current rating of

the Incomer in ampere shall be APFC Panel rating in KVAR x 1.4 x 1.5 or

Nearest higher standards rating.

(B) Instruments & Indications

i) 3-Phase current sensing APFC microprocessor relay/controller , advance

8/12 stages (8 stages for capacity below 100 KVAR and 12 stages 100 KVAR

& above) with Communication Ethernet/RS485/SNMP port open protocol for

BMS integration as per approved by Engineering in charge and having

display of Phase wise V, A, PF, Cos-Phi, Kw, KVA, KVAR, THD-V , THD-I,

harmonics up to 31 level. 3 nos of dual core CT's accuracy class 1, 15VA at

incomer of PCC Panel for APFC relay.

ii) Auto Manual Selector switch, auxiliary contactors with timer for delay in

iii) Digital Multi function meter with LED Display for V, A, PF, KW, KVA,

KVAR, THD-V & I, Frequency.

iv) Suitable rating control transformer shall be provided for control and

indication circuit.

v) All components like control transformer, meter, relay and indicating lamp

shall be protected by using suitable rating individual MCB's.

vi) Wiring of the control circuit shall be done by using 2.5 sq mm, FRLS 1100

V grade, PVC insulated multi stranded copper control wire.

1.3 Amp per Sq.mm, TPN, Electrolytic grade Aluminum bus bar of capacity

1.25 times of incomer rating as per CPWD specification.

b) For Active Section : Dedicated HMI (Human Machine Interface) (Minimum

7 inch display) for controlling and communication and having display of

Phase wise V, A, PF, Cos-Phi, KW, KVA, KVAR, THD-V , THD-I, harmonics

up to 50th level.Communication Ethernet/RS485/SNMP port open protocol

for BMS integration as per approved by Engineering in charge.

Digitally signed by PRIYA

Sr.No. Sch.No. Particulars Unit Qty Rate DSR Amount Non-DSR Rate

RELAYS AS PER SLD

Total For Subhead-IV Distribution Panel 5,34,906.00

D Subhead-IV L.T Cable Work

Supply and laying of aluminium conductor PVC insulated armoured served

sheathed cables 1100 Volts grade on cable tray as directed by engineer incharge

complete in all respect including The armouring of the cable shall be properly

connected with the earth conductor by clamps etc.

Supply ofPower/Control Copper Cables,Solid Copper conductor,XLPE

Insulated,cores laid up, PVC tape innersheathed,Unarmoured/Armour (Glavanised

2 MR wire for cables up to 14x1.5 sqmm, 9x2.5 sqmm,2x16 sqmm, 3x10

sqmm,4x10sqmm balance all galvanised steel strip),extruded PVC Type ST2

Sheathed, 650/1100 V grade as per IS 7098 (Part 1) 1988

b RA-17 35 sq. mm 3-1/2 core Meter -

Supply and fixing of brass nickle plated compression gland for PVC insulated &

armoured served sheathed, underground cable including rubber ring etc. complete

in all respect. The armouring of the cable shall be properly connected with the

earth as per direction of Engineer-Incharge.

Laying of one number PVC insulated and PVC sheathed / XLPE

4 7.5 power cable of 1.1 KV grade of following size in the existing

RCC/ HUME/ METAL pipe as required.

c 7.5.3 Above 95 sq. mm and upto 185 sq. mm Meter 200.00 81.13 16,226.00

Laying and fixing of one number PVC insulated and PVC

5 7.8 sheathed / XLPE power cable of 1.1 KV grade of following size

on cable tray as required.

a 7.8.1 Upto 35 sq. mm (clamped with 1mm thick saddle) Meter 200.00 47.41 9,482.00

Providing, laying and fixing following dia RCC pipe NP2 class

(light duty) in ground complete with RCC collars, jointing with

cement mortar 1:2 (1 cement : 2 fine sand) including trenching

(75 cm deep) and refilling etc as required. 300mm Dia

Supplying and laying of following size DWC HDPE pipe ISI marked along with all

accessories like socket, bend, couplers etc.

conforming to IS 14930, Part II complete with fitting and cutting,

jointing etc. in the existing trench, complete as required

Total For Subhead-V L.T Cable Work 99,795.47 4,40,100.00

E Subhead-V Earthing Work

Supply and burying of 600mm x 600mm x 6mm G.I. plate vertically for earthing

with its top at least 3 metres below ground level complete with 20mm dia G.I. pipe

and funnel for watering and one earthing lead of two no. 8 to 10 SWG GI wire in

1 15mm dia G.I. pipe up to switch board (from appron to switch board the cost of each 4.00 7,872.29 31,489.16

G.I. pipe and G.I. wire will be extra) 30cm square C.I. frame with hinged cover

masonry housing alternate layers of charcoal/coke and salt at least 150mm thick

alround etc. as per directions of Engineer-in-charge complete in all respect.

Supply and burying of 600mm x 600mm x 3mm copper plate vertically for earthing

with its top at least 3 metres below ground level complete with 20mm dia G.I. pipe

and funnel for watering and two earthing lead of two no. 8 SWG copper wire in

2 15mm dia G.I. pipe up to switch board (from appron to switch board the cost of each 4.00 14,579.32 58,317.28

G.I. pipe and copper wire will be extra) 30cm square C.I. frame with hinged cover

masonry housing alternate layers of charcoal/coke and salt at least 150mm thick

alround etc. complete in all respect.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as

strip earth electrode, including connection/ terminating with nut, bolt, spring,

washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of

brass nut bolt & spring washer spaced at 50mm)

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip

earth electrode, including connection/ terminating with G.I. nut, bolt, spring,

washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of

G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth

5 5.1 electrode including connection with brass nut, bolt, spring, washer excavation and Meter 20.00 1,634.09 32,681.80

re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth

6 5.11 electrode including connection with G.I. nut, bolt, spring, washer excavation and Meter 20.00 743.82 14,876.40

re-filling etc. as required.

Total For Subhead-VII Earthing Work 2,19,669.24 -

F Subhead-VI Cable Tray Work

Digitally signed by PRIYA

Sr.No. Sch.No. Particulars Unit Qty Rate DSR Amount Non-DSR Rate

Supplying and installing following size of perforated painted with powder coating

DSR 2022 M.S. cable trays with perforation not more than 17.5%, in convenient sections,

4.1 joined with connectors, suspended from the ceiling with M.S. suspenders including

bolts & nuts, painting suspenders etc. as required.

b 4.1.4 300 mm width X 50 mm depth X 1.6 mm thickness Meter 20.00 818.63 16,372.60

Total For Subhead-IX Cable Tray Work 16,372.60 -

G Subhead-VII DG Set

Supply, installation, Testing & Commissioning of 'Silent Type Diesel Generating set

as per CPCB IV + or better norms along with having Prime Power Rating of KVA as

below, 415 volts at 1500 RPM, 0.8 lagging power factor at 415 V suitable for 50 Hz,

3 phase system & for 0.85 Load Factor, including testing at factory and site with

fuel, load for test and other necessary arrangements Complete as per CPWD

specifications, should have QR code which should contain drawing, test report

OEM manual,Geo - Tag of manufacturing location, rating plate as per relevant IS

Code etc. and consisting of the followings:

(A) Diesel Engine:

Turbocharged Diesel engine 4 stroke water cooled, multi cylinder,

dynamically balanced fly wheel, electric start of suitable BHP at 1500 RPM suitable

for above output of alternator at 40 Degree C, 50% RH & at 1000 Meter MSL ,

capable of taking 10% over loading for one hour after 12 hours of continuous

operation. The engine will be with Electronic governor, Dry type Air filter with

service indicator, first filling of engine fuel (after commissioning) lubricating Oil,

Coolant and other consumables complete with all the required accessories, the

Electronic governor shall be as per ISO 8528.The engine shall comply to the latest

CPCB norms (CPCB IV + or better) and Conforming to BS 5514, BS 649, IS 10000, IS

10002, IS 13018 and as per CPWD specifications.

(B) Engine mounted Instrument Panel fitted with and having digital display for

(i) Start-stop switch with key

(ii) Water temperature indication

(iii) Lubrication oil pressure indication

(iv) Lubrication oil temperature indication

(v) Battery charging indication and Voltage indication

(vi) RPM indication

(vii) Over speed indication

(viii) Low lubricantion Oil trip indication

(ix) Engine Running Hours indication

(C) Alternator:

Synchronous alternator rated of appropriate KVA, 415 volts at 1500 RPM, 3

phase 50 Hz, AC supply with 0.8 lagging power factor at 40 Degree C, 50%

RH & at 1000 Meter MSL. The alternator shall be having Screen Protected

Drip Proof (SPDP) enclosure IP23, brushless, continuous duty, dynamically

balanced rotor, capable of taking 10% over loading for one hour after 12

hours of continuous operation, self cooled,self-excited and self-regulated

through AVR conforming to IS13364(Part 2)/IS: 4722/BS 2613 suitable for

tropical conditions and with class- H insulation.

(D) Base Frame & Foundation:

Both the engine and alternator shall be mounted on suitable base frame

made of MS channel with necessary reinforcement which shall be installed

on suitable cement concrete foundation and vibration isolation arrangement

as per recommendations of manufacturer.

Daily service fuel tank of suitable liters capacity as per CPWD Specifications,

fabricated out of 3 mm thick M.S. sheet complete with all standard

accessories and fuel piping between fuel tank and diesel engine with MS

class 'C' pipes of suitable dia. Complete with valves, level indications &

accessories as required as per specifications.

(F) Exhaust System:

Dry exhaust manifold with hospital type exhaust silencer and catalytic

(G) Starting System:

12V/24V DC starting system comprising of starter motors: voltage regulator and

arrangement for initial excitation complete with suitable numbers of batteries

(180 AH capacity lead acid SMF type) as required as per specifications. The battery

shall be housed inside the acoustic enclosure of DG Set.

(H) Acoustic and weather proof enclosure with arrangement for fresh air intake for

cooling of the engine & alternator, extraction, discharging hot air in to the

atmosphere and the temperature rise inside the enclosure, noise level

outside enclosure. The acoustic enclosure should be suitable for cable

connection/connection through bus-trunking. Such arrangements on acoustic

enclosure should be water proof & dust-proof conforming to IP-65 protection. The

enclosure shall be as per CPCB IV + or better norms etc. and as per CPWD

specifications.

Free standing floor mounted IP 42 automatic mains failure control panel

including auto by-pass, suitable for KVA as below for silent type DG set

complete with relays, timers, set of CTs for metering & protection and energy

analyser to indicate currents, phase and line voltages, frequency, power factor,

KWH, Kilo Volt Ampere Reative Hour (KVARH), KVA (Phase & Total), KW &

provision for overload, short circuit, restricted earth fault, under frequency, power

(aluminum) and control (copper ) cabling of suitable size upto 15 meter between

AMF panel, LT Panel and DG Set including connection interconnection etc. as

required, all complete and inter locking and communication/ Ethernet

/RS485/SNMP port open protocol for BMS integration including suitable software,

the panel shall be of DG Set OEM make etc. as per approved by Engineering in

charge and including the following:

Digitally signed by PRIYA

Sr.No. Sch.No. Particulars Unit Qty Rate DSR Amount Non-DSR Rate

1. Suitable numbers and appropriate capacity 4 pole motorised

electrically operated draw out with cradle type 3 position ACB/ MCCB

with electronic release for O/C & E/F and shunt trip.

2. Auto/Manual/Test/Off selector switch

3. Protection for under and over voltage phase reversal (2 nos Over

voltage relay, 2 Nos. reverse power relay and 2 Nos. under voltage

4. 3 Sets of current transformers 15 P 10 accuracy for protection and 15

VA class-I for metering

5. Energy analyser unit to indicate current, Voltage( L-N & L-L), kW, kVA

(Phase & Total), Frequency, KWH, PF.

6. LED Indicating lamps for load on mains and load on set.

7. Fuse/ MCB for instruments.

8. Battery charger, complete with transformer/ rectifier, D.C. voltmeter

and ammeter, selector switch for trickle, off and boost and current

9. Main supply failure monitor.

10. Supply failure timer.

11. Restoration timer

12. Control unit with three impulse automatic engine start/stop and failure

to start lockout.

13. Impulse counter with locking and reset facility.

14. ON/OFF/Control circuit switch with indicator

15. Audio/Video annunciation for

(i) High water temperature

(ii) Low lubricating oil pressure

(iii) Engine over speed

(iv) Engine fails to start

(v) Full load/maximum load warning

16. Protection for over/under Frequency, Loss of AC sensing, Over

Current, Unbalancing load with suitable number of relays and

17. Maintenance notification based on Engine Run Hour & due date.

18. Load Management through PLC to achieve auto opening and closing of

incomer breakers, bus coupler switching of essential panel ,

interlocking providing signal to AMF Panel for load status and AMF

shall give command to DG Set to auto start / auto stop depending upon

load status and requirement etc. and necessary hardware and

software required to perform the operation shall be provided by the

contractor including all control wiring.

Supply and laying of aluminium conductor PVC insulated armoured served

sheathed cables 1100 Volts grade on cable tray as directed by engineer incharge

complete in all respect including The armouring of the cable shall be properly

connected with the earth conductor by clamps etc.

Total For Subhead-III DG Set 6,24,108.00

H Subhead-VIII On Grid Solar Power Backup System

On Grid Solar System Work

Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power

Plant conformington MNRE specifications as amended, consisting of Mono

Crystalline silicon solar cells, netmetering facility, necessary protections, earthing,

mounted on Aluminium/GI structure of suitable strength with following

components complete as required:-a)Solar Photovoltaic Module of capacity

330Wp or above, manufactured in India, conforming to IS14286/IEC61215,

IS/IEC61730-Part-1, IS/IEC61730-Part-2. Solar Photovoltaic Module conversion

efficiency shall not be less than 16.5%. PV modules used in solar power

plants/systems must be warranted for their output peak watt capacity, which

should not be less than 90% at the end of 10years and 80% at the end of 25 years

b)Power Conditioning Unit (PCU) of 350-800VDC Input voltage range and 400VAC,

three phase, 4wire, 50Hz+/-2.5Hz, out put voltage suitable to generate AC Power

with efficiency not less than 97%, total harmonic distortion less than 3% and

suitable for ambient temperature from 0to50degree C. The PCU shall adjust the

voltage and frequency level to suit the Grid Voltage Frequency.c) Data Monitoring

System complete with accessories.

d) Fixing of Array junction box & Main junction box with IP65 protection and

termination arrangement for in coming and outgoing cable alongwith glands, lugs

and other accessories etc. as required.

e) Lightning and surge voltage

protection.f)Connections&Interconnectionsbysupplying&fixingrequiredsizeXLPEins

ulatedcopperconductor1.1kVgradearmouredpowerandcontrolcablesbetweensolar

modules,mainpowercabletogridsupplyPCUunitalongwithsupplying&fixingofnecessa

rychannel/conduitlugsandotheraccessoriesetc.asrequired.

Subhead-X On Grid Solar Power Backup System 6,43,310.70 -

Uninterrupted Power Supply

Digitally signed by PRIYA

Sr.No. Sch.No. Particulars Unit Qty Rate DSR Amount Non-DSR Rate

Online UPS- Input supply: Three Phase, Output supply: Three Phase

Supplying, installation, Testing & Commissioning of of following capacity at full

load (Unity Power Factor) at operating temperature 0 to 40 deg C,

Relative humidity 0 to 95%, Online double conversion true sine wave

Uninterrupted hot swappable (allow for the replacement or addition of

battery modules without shutting down the entire system) modular Power

Supply (UPS) system with N+1 modules (N denotes total number of moduels -

requird for rated capacity). The UPS shall include a Rectifier, inverter, battery bank

suitable for 30 minutes back up (Battery VAH capacity shall not be less than 1600

VAH per KVA of UPS rating per Hour backup time) on full load (Battery shall be

VRLA, SMF in ABS Container) and Static Bypass switch alongwith provision for

manual bypass, suitable isolation transformer for additional protection against

neutral faults etc. UPS shall have inbuilt

phase sequence correction. The UPS systems offered are to be of the latest

technology with Digital Control Microprocessor based for reliable operation using

Insulated Gate Bipolar Transistor (IGBT)'s both for the rectifier & inverter (3 Level)

with PWM (Pulse Width Modulation). The quality of design, manufacturing and

inspection process should confirm to the relevant International standards such as -

IEC/EN/VDE. The operating efficiency of the UPS systems shall be >96% while

operating on battery mode and delivering quality power to the 100% non-linear

loads. Current total harmonic effect(ITHD) on the input grid shall be < 5% at 50

%load. (The required LC (

inductor (L) and a capacitor (C)) filters shall be included in UPS cost),

extreme power factor kit to be included to limit the input power factor (PF) to 0.99

and output power factor shall be unity (i.e. kw rating of the UPS shall be kva rating

x 1 ), however UPS shall be suitable to take load at 0.7 laging to 0.7 leading power

factor loads. UPS shall be suitable for incoming supply AC : 3Phase 400V +/-20%,

50 Hz +/-5 Hz, AC Output voltage: 3Phase 415 Volt, 50 Hz +/- 0.2Hz, Overload

capacity of 120% for 10 mins, Sine wave output. Non condensing, noise level less -

than 60db at 1 meter distance, protections: Input Under voltage over voltage,

abnormal out voltage, battery over charging, output over current, short circuit

protection, battery deep discharge protection, 10KV surge. UPS must comply with

low voltage electromagnetic compatibility (EMC) achieved as per EN 6204, EN6204

Part I and Part 2, it shall be a Voltage and Frequency Independent (VFI)-type UPS.

Communication RS232/RS485/SNMP port open protocol for BMS

integration, all hardware & software for iOT Communication as per approved by

Engineering in charge. Required battery racks and interconnecting copper

conductor cables of suitable size and connectors and all required accoseries are

inclusive of the cost). This system must provide a means for logging and alarming

of all monitored points plus email notification. Forced air-cooling with integral

inbuilt fans with redundancy (if one fan fail UPS should be able to handle at least -

80% of the load, Noise Level 65 DB at 1 meter distance. The system shall be in

compliance IEC 62040- 1,2 & 3, IS: 16242 and CPWD Specification. Display Panel

(minimum) (In-build 5 inch or more LC Display / LED ) to display : a) Input: Voltage,

current, Frequency. b) Bypass: Voltage, Frequency. c) Output: Voltage, frequency,

d) Battery: Voltage, Capacity. e) Load: KVA, KW, Percentage.

f)Temperature: STS, Inverter, PFC. g) Event Logging & Statistical Data (On

LCD/LED): UPS should capture and display up to 3000 events like: Over

temperature / DC Bus Fail / Fan Fail / Fuse Fail / Overload / Short-circuit /

Device Fail / Inverter Fail / Rectifier Fail / Bypass Fail, etc. h) Statistical Data: No. of

power failures / Transfers to Bypass / Total Running time, etc. i) Mains Mode of

Operation /Battery Mode of Operation / Bypass feeding the load /UPS Fault -

/Battery charging and discharging, overload, battery voltage and battery capacity.

j) Audible Alarms : Mains Failure, Battery Low Alarm, UPS Overload, Fault,

Shutdown, Input Over, Under Voltage, Output Over, Under Voltage, Battery Over,

Under Voltage, Over Load and short circuit, Over Temperature. The UPS should

have QR code which should contain drawing, test report OEM manual,Geo- Tag of

manufacturing location etc

MR UPS Output Panel Set 2.00 60,000.00 1,20,000.00

Total Uninterrupted Power Supply:- 4,61,772.00

Supply, Installation, Testing & Commissioning Full range Ceiling loudspeaker with

1x 2.25"transducer, Frequency response: 95Hz to 16kHz; Power handling capacity:

16 Watt; Nominal dispersion: 145° Conical; Sensitivity: 86 dB SPL and Max SPL: 98

dB SPL; Nominal Impedance: 16 Ohms or 70/100V; Integral multi-tap Transformer

with tap settings: 2/4/8/16 W @70V/100V. Installation: Indoor complete with

standard accessories as required.

Supply, Installation, Testing & Commissioning of OEM manufacturing Bi-pivot

MR bracket for mounting the above given loudspeaker complete with standard Nos. 4.00 15,940.68 63,762.71

accessories as required.

Supply, Installation, Testing & Commissioning of Dual channel power amplifier;

Should have Power output: 1x 100W @4-8Ω, 70/100V or better; should have

Frequency response : 20Hz-20kHz or better; Total harmonic distortion (THD) : <

MR 0.04% or better; should have V-bridged output power : 1x 1200W @2-4Ω or Nos 2.00 25,600.00 51,200.00

70/100V or better; Channel seperation (crosstalk): > 80 dB; Dynamic range: ≥100

dBA; Input Impedance: 10kΩ; 8-digital I/O primary/secondary ports complete with

standard accessories as required.

Supply, Installation, Testing & Commissioning of Pre-polarized condenser

Gooseneck microphone with Cardioid polar pattern; Gooseneck length: 400mm;

Operating principle: Pressure gradient; Microphone Frequency response: 50Hz -

20,000Hz; Nominal Impedance: < 100 Ω; Signal to noise ratio: 26dB(A); Max. SPL:

130 dB; Connection: 3-pin XLR; Wired Table-top stand having 3-pin XLR

connection, bi-color LED light ring for visual feedback

Supply, Installation, Testing & Commissioning of 2 core 14AWG PVC insulated Cu

MR conduction speaker cable, 100 Mtrs Roll complete with standard accessories as Nos 50.00 109.80 5,490.00

Digitally signed by PRIYA

Sr.No. Sch.No. Particulars Unit Qty Rate DSR Amount Non-DSR Rate

Supply, Installation, Testing & Commissioning of Connectors & patch cables

complete with standard accessories as required.

Video System - -

Supply, Installation, Testing & Commissioning of : LASER Projector : WUXGA (1920

x 1200 Pixels or higher) Full HD Resolution, Brightness 5000 Lumens or higher,

MR Aspect Ratio 16:10, Contrast Ratio :2500000:1 or better, Light source Laser, Lamp Nos 2.00 2,21,484.00 4,42,968.00

life 20000 Hrs or higher, Projector Stand ,Input: HDMI, VGA, Audio etc. complete in

Supply, Installation, Testing & Commissioning of : 130" (AR 16:10) Tab Tensioned

Motorised Projection Screen Matte white, Projection Surface, builtin motor system

with IR/RF receiver, remote based, high gain & viewing angle , Noise less Up/Down

operation, Iamge Size: Min. 130' Diagonal etc. all complete.

Supply, Installation, fixing, Testing & Commissioning of Interactive Flat Panel

Display (86 inch interactive flat panel with android latest version, 8GB RAM, 64GB

memory with octa core processer.) or as required along with fixed/adjustable wall

mount Bracket flushed or recessed as per site conditions and requirement of user.

Supply, Installation, Testing & Commissioning of Full HD IP PTZ camera with 4X

optical zoom, Resolution 1080p@60Hz, Sensor 1/2.8" 2MP CMOS, Interfaces: 3G-

SDI/ HDMI, 1x Mic/ line In, output: Ethernet, 1x USB3.0, Viewing angle

RTSP/RTMP/RTMPS complete with standard accessories as required.

Supply, Installation, Testing & Commissioning of Mounting/ Hanging arrangements

for the above given Camera complete with standard accessories as required.

Supply, Installation, Testing & Commissioning of 1 Mtrs USB-USB C-type cable,

MR should have USB3.1 Gen 1 or better complete with standard accessories as Nos 1.00 2,306.44 2,306.44

Supply, Installation, Testing & Commissioning of 2 Mtrs USB-USB, USB-A to USB-B

moulded Cable complete with standard accessories as required.

Supply, Installation, Testing & Commissioning of 2 Mtrs USB 3.0 A to A (Male)

Molded Cable complete with standard accessories as required.

Supply, Installation, Testing & Commissioning 2 Mtrs HDMI-HDMI cable complete

with standard accessories as required.

DSR 2022 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/

1.54 recessed Steel/ PVC conduit as required.

Supplying and fixing of following sizes of steel conduit along

with accessories in surface/recess including painting in case of

surface conduit, or cutting the wall and making good the same

in case of recessed conduit as required. 25mm Dia

Total Audio System:- 72,468.61 14,64,367.83

VRV Based HVAC System Work

7.2 VRV/VRF Out Door units :

Supply, Installation, Testing & Commissioning of Modular type Variable

Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units

suitable for cooling/heating having 100% hermetically sealed inverter type twin

Rotary/Scroll Compressor(s), minimum two compressors (with individual seperate

PCB) for above 14HP modules, icroprocessor based Controller, top discharge type

condensing unit(s), with R-410-A Refrigerant or equivalent, vibration Isolators with

suitable foundation etc. complete as required. To have better efficiency condensor

fan shall be capable to operate at different speed with respect to load. The unit

shall deliver the rated capacity and in confirmation as per IS 18728:2024 and

CPWD Specifications and work even at 50°C ambient temperature without

tripping. The system shall be able to deliver 100% of the rated capacity upto 39

Degree Celcius. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz

AC power supply and BMS compatible. The unit shall be filled with first charge of

the refrigerant and ready for use as required. The condenser should be coated

with a hydrophilic film to prevent water accumulation on the surface of the heat

exchanger, enhance water dispersion, and reduce the risk of degradation, thereby

improving overall performance and durability. The Indian Seasonal Energy

Efficiency Ratio (ISEER) of the unit shall be as per Energy Conservation and

Sustainable Building Code (ECSBC) 2024 as below and complete as per CPWD

specification, connections, inter connections etc. as required. (For capacity <40

kWr ISEER 6.4, Capacity >40 and <70 ISEER 6.5, Capacity > 70 ISEER 6.6 for ECSBC+

Building) For Cooling or Heating or Both

Supply, Installation, Testing and Commissioning of following minimum

capacity 4 way Cassette Type Indoor ceiling mounted unit equipped with synthetic

washable media pre-filter, fan section with low noise fan /dynamically balanced

blower, multispeed motor, coil section with DX Copper coil, electronic expansion

valve, outer cabinet, drain pump, grill, necessary supports, vibration Isolation,

7.4 Corded remote control etc., suitable for operation on single phase 230 V ± 10%,

50Hz AC supply, complete, as required. The Indoor units must shut down upon

receiving a singal from the BMS System/Fire Signals. The system shall be capable

to adjust air flow as per room requirement in auto mode. The cooling capacity of

indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB

Wall Monuted Type units: -

Digitally signed by PRIYA

Sr.No. Sch.No. Particulars Unit Qty Rate DSR Amount Non-DSR Rate

Supply, Installation, Testing and Commissioning of following minimum

capacity High wall type Indoor unit equipped with and comfort washable

synthetic media pre-filter, fan section with low noise fan/dynamically

balanced blower, multispeed motor, coil section with DX copper coil,

electronic expansion valve, outer cabinet, cord less remote control, drain pan,

necessary accessories etc., suitable for operation on 230 V ± 10%, 50Hz, single -

phase AC supply, complete as required. The Indoor units must shut down upon

receiving a singal from the BMS System/Fire Singnals. The system shall be capable

to adjust air flow as per room requirement automatically. The cooling capacity of

indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB

Supply, Installation, Testing and Commissioning of Y/T/Multi Joints. Joints shall be

of same Original Equipment Manufacturer (OEM) make as of ODUs and IDUs

MR Indoor Units Nos. 35.00 4,535.00 1,58,725.00

MR Outdoor Units Multi Joint Nos. 5.00 8,098.00 40,490.00

Supply,Installation,testing and commissioning of corded Cord type remote control

with thermostat, LED Display and internal wiring for Cassette & hi-wall .

7.14 COPPER REFRIGERANT PIPING -

Supply, Installation, testing and commissioning including vaccumiazation and

Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant

piping for VRV/VRF system, complete with fittings, with suitable adjustable ring

type hanger supports, jointing/brazing including accessories, insulated with XPLE -

Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber

tubular sleeves sections of specified thickness as given below for Suction and

Liquid lines, all accessories as per specifications etc. as required :

MR 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 90.00 256.00 23,040.00

MR 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 300.00 346.00 1,03,800.00

MR 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 85.00 487.00 41,395.00

MR 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 150.00 615.00 92,250.00

MR 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 55.00 739.00 40,645.00

MR 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 45.00 904.00 40,680.00

MR 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 105.00 1,157.00 1,21,485.00

MR 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt 75.00 1,286.00 96,450.00

MR 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt 175.00 1,368.00 2,39,400.00

Supply installation testing commissioning Shielded Control Cables for VRV System

MR with necessary ISI mark Medium class rigid PVC pipes with necessary accessories -

with termination in machine and control equipments.

MR 2Cx1.5 Sq mm Shielded Armoured(for communication lead & remote ) Rmt 560.00 189.20 1,05,952.00

Supplying & erecting XLPE(IS:7098)(I) -88 ISI unarmoured copper cable 1.1 KV grade

to be erected as directed of following size.

MR 3C x 2.5 sq.mm FOR INDOOR UNIT POWER CABLE Rmt 567.00 210.50 1,19,353.50

MR Drain Piping : -

Rigid UPVC drain pipe of 10 Kg/cm2. rating with 9 mm thick.nitrile rubber

Total VRV Based HVAC System Work:- 27,67,523.70

Access Control System

Supply, Installation, Testing and Commissioning IP based

MR Fingerprint Biometric Reader with built in Smart card Reader, Power supply with Each 1.00 18,500.00 18,500.00

wiegand output fully networkable.

Supplying and fixing of following sizes of steel conduit along with accessories in

surface/recess including painting in case of surface conduit, or cutting the wall and

making good the same in case of recessed conduit as required.

Total Access Control System:- 22,151.65 18,500.00

Fire Fighting Work

Supplying, installation, testing and commissioning of electric driven terrace pump

1 18.4 suitable for automatic operation and consiting of following, complete in all

respects, as required:

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe

conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges,

2 18.7 tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable -

clamp/support frame and painting with two or more coats of synthetic enamel

paint of required shade complete as required :

Supplying and fixing single headed internal hydrant valve with instantaneous

Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked

conforming to IS 5290 (Type -A) with blank Gunmetal/ Stainless Steel cap and

chain as required :

a 18.9.1 Single headed Gunmetal Set 3.00 8,055.61 24,166.83 -

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with

4 18.11 bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets -

conforming to IS 13095 of following sizes as required :

Digitally signed by PRIYA

Sr.No. Sch.No. Particulars Unit Qty Rate DSR Amount Non-DSR Rate

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade

304) with orifice of required size to be fitted between flange & landing valve of

external and internal hydrants to reduce pressure at the outlet to the level of

3.5kg/cm2 complete as required.

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and

6 18.16 female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) -

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post

office red, conforming to IS 884 complete with the following as required.

20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2

as per IS: 12585

20 mm nominal internal dia gun metal globe valve & nozzle. -

Drum and brackets for fixing the equipmets on wall. Connections from riser with

25 mm dia stop gun metal valve & M.S. Pipe and socket.

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal

9 18.18 internal diameter size nozzle conforming to IS 903 suitable for instantaneous -

connection to interconnect hose pipe coupling as required :

Providing & Placing on terrace (at all floor levels) polyethylene water storage tank

IS : 12701 marked, with cover and suitable locking arrangement and making

necessary holes for inlet, outlet and overflow pipes but without fittings and the

base support for tank.

Providing and fixing Fire hose cabinet glazed door shutter and frame with hold

fasts (frame fabricated from 40x40x5mm and shutter from 35x35x5mm M.S.

angle) 2100mm high x 1000mm wide with locking arrangement, 4mm thick glass

with MS flats including all accessories, painting with one coat of steel primer and

two coats of postal red enamel paint. The words “Fire Hose Cabinet” to be painted

12 MR Providing and fixing air release valve Each 1.00 1,516.52 1,516.52

13 RA-4 Fire Extinguisher -

Providing and fixing 6 Kg clean agent or ABC extinguisher with IS: 2171. (ISI

Providing and fixing 4.5 Kg clean agent or CO2 extinguisher with IS: 2171. (ISI

14 MR Providing and fixining gun matel ball valve Each 3.00 1,037.01 3,111.02

15 MR Providing and fixining pressure gauge Each 3.00 472.73 1,418.19

16 MR Providing and fixing fire man axe Each 3.00 319.10 957.29

Supply Installation Testing and Commissioning of DOL starter panel with NO-NC

contact as required.

Supply and Laying of Aluminium Conductor PVC insulated armoured served

sheathed cables 1100V grade on cable tray as directed by Engineer in Charge

complete in all respect including excavation and refilling. The armouring of the

cable shall be properly connected with the earth conductor by clamps etc.

a 4CX16Sq.mm Cable Mtr. 50.00 -

Supplying and making end termination with brass compression gland and

19 aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE -

aluminium conductor cable of 1.1 KV grade as required.

Total Fire Fighting Work:- 3,13,838.37 1,74,430.48

Illuminated Signages

Supply, Installation & commissioning of stainless steel (305 grade) backlit signage

MR of different of sizes in alfabet & logo complete in all respect as directed by each 13.00 1,200.00 15,600.00

Engineer Incharge.

Total Illuminated Signages:- 15,600.00

Digitally signed by PRIYA

SCHEDULE OF QUANTITIES FOR PLUMBING WORKS

INTERNAL PLUMBING WORKS

DSR(2023) DESCRIPTION QTY UNIT Rate AMOUNT AMOUNT

I SANITARY INSTALLATIONS & C.P FITTINGS

Providing and fixing white vitreous china extended wall mounting water closet

of size 780x370x690 mm of approved shape including providing & fixing white

2 17.78 DSR vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre 10.00 each 14,594.17 1,45,941.70

(adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts,

bolts and gasket etc complete.

Providing & fixing white vitreous china Under Counter wash basin with C.I.

3 MR M.R. brackets painted white, with rubber plug, 32mm C.P. brass waste of standerd

pattern including cutting & making good the walls wherever required.

a)White Vitreous China Wash basin size (605x410x200)mm Jaquar (FNS-WHT-

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C.

waste fittings complete.

17.28.1 Semi rigid pipe

Providing and fixing 600x450mm bevelled edge mirror of superior glass (of

5 17.31 DSR approved quality) complete with 6mm thick hard board ground fixed to wooden 10.00 each 1,564.54 15,645.40

cleats with C.P. brass screws and washers complete.

Providing and fixing Stainless Steel AISI 304(18/8) kitchen sink as per IS :

6 17.10 DSR 13983 with C.I. brackets and stainless steel plug 40mm including painting of

fittings and brackets, cutting and making good the walls wherrerever required.

17.10.2.1 DSR Kitchen sink without drain board Size 610x510 mm bowl depth 200 mm 1.00 each 4,807.40 4,807.40

Providing and fixing white vitreous china battery based infrared sensor operated

urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with

7 17.80 DSR water (250 ml & 500 ml consumption), having water inlet from back side, 4.00 each 7,763.76 31,055.04

including fixing to wall with suitable brackets all as per manufacturers

specification and direction of Engineer-in-charge.

Providing and fixing stone slab table rubbed, edges rounded and polished of

size 75x50cm deep and 1.8cm thick fixed in Urinal partitions by cutting a chase

8 8.10 DSR of appropriate width with chase cutter and embedding the stone in the chase

with epoxy grout or with cement concrete 1:2:4 (1cement: 2coarse sand:

4graded stone aggregate 6mm nominal size) as per direction of Engineer-in-

charge and finished smooth.

8.10.2 Granite Stone of approved shade 2.00 Sqm. 3,942.45 7,884.90

CP Brass fittings

7 18.21 Providing and fixing unplasticised PVC connection pipe with brass unions.

18.21.2 DSR 45 cm length

18.21.2.1 DSR 15 mm nominal bore 32.00 each 95.11 3,043.52

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre

8 17.16A DSR long with S.S. triangular plate to Eureopean & Wall moutain type W.C. of 10.00 each 339.72 3,397.20

quality and make as approved by Engineer - in - charge.

Providing and fixing C.P. brass bib cock of approved quality conforming to

18.49.1 DSR a) 15 mm nominal bore 10.00 each 493.12 4,931.20

Providing and fixing C.P. brass long body bib cock of approved quality

conforming to IS standards and weighing not less than 690 gms. ( for sink)

18.51.1 DSR a) 15 mm nominal bore 2.00 each 777.38 1,554.76

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of

approved quality conforming to IS:8931

18.53.1 DSR a) 15 mm nominal bore 21.00 each 558.79 11,734.59

Central Hole Basin Mixer with Popup Waste System with 450mm LongBraided

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality &

make and as per the direction of Engineer-in-charge.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high

and 112 mm distance from wall of standard shape with bracket of the same

materials with snap fittings of approved quality and colour, weighing not less

Providing and fixing PTMT towel rail complete with brackets fixed to wooden

19 17.73 DSR cleats with CP brass screws with concealed fittings arrangement of approved

quality and colour.

450 mm long towel rail with total length of 495 mm, 78 mm wide and effective

height of 88 mm, weighing not less than 170 gms.

Digitally signed by PRIYA

SCHEDULE OF QUANTITIES FOR PLUMBING WORKS

INTERNAL PLUMBING WORKS

DSR(2023) DESCRIPTION QTY UNIT Rate AMOUNT AMOUNT

20 17.34 DSR Providing and Fixing Toilet Paper Holder:

II C.I. SOIL WASTE & VENT PIPES AND FITTINGS

21 Providing & fixing soil, waste and vent pipes.

Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside

17.35.1.3 DSR a) 100mm dia centrifugally cast iron S & S pipe. 40.00 Rm. 1,137.73 45,509.20

17.35.2.3 DSR b) 75mm dia centrifugally cast iron S & S pipe. 24.00 Rm. 938.22 22,517.28

Providing and fixing GI pipes complete with GI fittings and clamps,

including cutting and making good walls etc. ( for wash basin waste )

18.10.4 DSR 32mm dia nominal bore 28.00 Metre 648.99 18,171.72

23 Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe.

17.57A.1 DSR a) 100mm

17.57A.1.1 SS 304 grade coupling with EPDM rubber gasket 13.33 each 420.38 5,605.07

17.57A.2 DSR b)75mm

17.57A.2.1 SS 304 grade coupling with EPDM rubber gasket 8.00 each 378.55 3,028.40

Providing & fixing M.S. holder bat clamps of approved design to sand cast

iron/centrifugally cast (Spun) iron S & S pipe embeded in & including cement

concrete blocks 10x10x10cm. of 1:2:4 mix (1 cement : 2 coarse : 4 graded

stone aggregate 20mm nominal

size). Including cost of cutting holes & making good the walls etc.

25 Providing & fixing cast iron coller.

Providing and fixing trap of self cleansing design with screwed down or hinged

26 grating with or without vent arm complete, including cost of cutting and making

good the walls and floors :

Providing and fixing bend of required degree with access door, insertion rubber

washer 3mm thick, bolts and nuts complete.

Providing and fixing plain bend of required degree.Hubless centrifugally cast

(spun) iron pipes epoxy coated inside & outside IS:15905

Providing and fixing single equal plain junction of required degree with access

door, insertion rubber washer 3 mm thick, bolts and nuts complete.

Providing and fixing centrifugaly cast iron single equal plain junction of required

Providing and fixing single unequal junction of required degree with access

door, insertion rubber washer 3 mm thick, bolts and nuts complete :

32 Providing and fixing single unequal plain invert branch of required degree :

Providing and fixing door piece, insertion rubber washer 3mm thick, bolts &

nuts complete :( c.o.p.)

34 Providing and fixing cast iron terminal guard.

Digitally signed by PRIYA

SCHEDULE OF QUANTITIES FOR PLUMBING WORKS

INTERNAL PLUMBING WORKS

DSR(2023) DESCRIPTION QTY UNIT Rate AMOUNT AMOUNT

III INTERNAL RAIN WATER DRAINAGE WORK

Providing and laying cement concrete 1:5:10(1 cement : 5 coarse sand : 10

19.2. graded stone aggregate 20mm nominal size) around P.V.C Soil and waste pipe

including bed concrete as per standard design(embedded in the flooring /

Providing and fixing on wall face unplasticised -Rigid PVC rain water pipes

37 12.41 conforming to IS: 13592 Type A including jointing with seal ring conforming to

IS: 5382 leaving 10mm gap for thermal expansion.

Providing and fixing on wall face unplasticised PVC moulded fittings/accessories

for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A

including jointing with seal ring conforming to IS:5382 leaving 10mm gap for

thermal expansion.

12.42.1 DSR Coupler

12.42.5.2 DSR Bend 87.5 degree

12.42.6 DSR Shoe (Plain)

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15

cm diameter and weighing not less than 440 grams.

Providing and fixing unplasticised -PVC pipe clips of approved design to

unplasticised -PVC rain water pipes by means of 50x50x50 mm hard wood plugs,

42 12.43 screwed with MS screws of required length including cutting brick work and

fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the

wall etc. complete.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement

concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm

nominal size) over PVC sheet 1m x 1 m x 400 micron, finished with 12 mm

cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat

cement,punning,rounding the edges and making and finishing the outlet

TOTAL [III] 22,439.52 -

IV INTERNAL WATER SUPPLY WORKS

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having

thermal stability for hot & cold water supply including all CPVC plain & brass

threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes

jointing of pipes & fittings with one step CPVC solvent cement and the cost of

cutting chases and making good the same including testiang of joints complete

as per direction of Engineer in Charge.

Concealed work including cutting chases and making good the walls etc.

18.8.1 DSR 15mm dia nominal outer dia pipes 10.00 Rm. 484.36 4,843.60

18.8.2 DSR 20mm dia nominal outer dia pipes 28.00 Rm. 523.08 14,646.24

18.8.3 DSR 25mm dia nominal outer dia pipes 18.00 Rm. 610.31 10,985.58

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having

thermal stability for hot & cold water supply, including all CPVC plain & brass

45 threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This

includes jointing of pipes & fittings with one step CPVC solvent cement and

testing of joints complete as per direction of Engineer in Charge.

Internal work-Exposed on wall

18.7.2 DSR 20mm dia nominal bore 12.00 Metre 325.96 3,911.52

18.7.3 DSR 25mm dia nominal bore 12.00 Metre 390.71 4,688.52

18.7.4 DSR 32mm dia nominal bore 15.00 Metre 504.74 7,571.10

18.7.5 DSR 40mm dia nominal bore 10.00 Metre 683.97 6,839.70

47 18.17 Providing and fixing gun metal gate valve with wheel of approved quality.

18.17.1 DSR 25mm dia nominal bore 2.00 Each 605.60 1,211.20

18.17.2 DSR 32mm dia nominal bore 2.00 Each 670.98 1,341.96

17.17.3 DSR 40mm dia nominal bore 2.00 Each 803.80 1,607.60

Providing and fixing ball valve (brass) of approved quality, High or low

pressure, with plastic floats complete :

18.18.3 DSR 25 mm nominal bore 2.00 Nos. 451.52 903.04

Digitally signed by PRIYA

SCHEDULE OF QUANTITIES FOR PLUMBING WORKS

INTERNAL PLUMBING WORKS

DSR(2023) DESCRIPTION QTY UNIT Rate AMOUNT AMOUNT

Providing and fixing motorized butterfly valves the valve should be able to

oprate with hot/cold water medium between 20---120 degree working

temperature, the nominal pressure of the valve should be PN 16, leakage rate

through the valve disc should be Rate-A Bubble tight to EN1266-1 with

integrated flange sealing should ensure positive connection of the valve body

seat ring and valve disc and provide a complete isolation of the media from the

body. The disc casting should be precision machined and should give a smooth

49 M.R. and close disc-to-seat relationship. The stem bearing should comprise of non

corrosive PTFE bushing to completely isolate the valve seat from the body,

resulting in increase control of the valve disc, lower valve seating torque and

longer valve life. The disc should be stainless steel to offer a good corrosion

resistance, superior resistance to a broad range of chemical enviorments as well

as very low co-efficient of friction and excellent resistance to impact and ultra-

violet radiation. For temperatures and rust proof operation the valve disc should

mm nominal material. (Make: Belmio)

TOTAL FOR INTERNAL PLUMBING SYSTEM 4,84,000.49 63,519.70

Digitally signed by PRIYA

(COST OF EXTERNAL SEWERAGE, DRAINAGE & EXTERNAL WATER SUPPLY WORKS)

Construction of Officie Building for the Institute of Company Secretaries of India (ICSI) at Raipur (CG)

SOR/DSR. DESCRIPTION QTY. UNIT Rate Rate D.S.R AMOUNT

I RISING MAIN AND BYE PASS ARRANGEMENT

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply including all

CPVC plain & brass threaded fittings This includes jointing of

pipes & fittings with one step CPVC solvent cement, trenching,

refilling & testing of joints complete as per direction of Engineer

DSR 18.9.6 50 mm nominal dia Pipes 160 RM 794.25 772.81 1,23,649.60

DISTRIBUTION SYSTEM

Providing and fixing gun metal gate valve with C.I. wheel of

approved quality (screwed end) :

Constructing brick masonry chamber 600 x 600 x 750 mm

inside with F.P.S. brick work in cement mortar 1:4 (1 cement :

4 coarse sand) for Sluice Valve / Air Valve, with C. I. surface

box 100 mm top diameter, 160 mm bottom diameter and

180mm deep (inside) with chained lid and RCC top slab with 1 :

16 DSR 18.33.1 2 : 4 mix (1 cement : 2 coarse sand : 4 grade stone aggregate 8.00 Each 10862.40 10569.12 84,552.96

20 mm nominal size); necessary excavation, foundation

concrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone

aggregate 40 mm nominal size) and inside plastering with

cement mortar 1 : 3 (1 cement : 3 coarse sand ) 12 mm thick

finished with a floating coat of neat cement complete as per

standard design

TOTAL COST OF EX.WATER SUPPLY 2,16,194.00 -

Digitally signed by PRIYA

Construction of Officie Building for the Institute of Company Secretaries of India (ICSI) at Raipur (CG)

BILL OF QUANTITIES

S. DSR RATE RATE AMOUNT

DESCRIPTION UNIT QTY

SECTION - VI TUBE WELL INSTALLATIONS (As per D.S.R.2018)

Boring/drilling bore well of required dia for casing/ strainer pipe,

by suitable method prescribed in IS: 2800 (part I), including

collecting samples from different strata, preparing and submitting

1.0 23.1 strata chart/ bore log, including hire & running charges of all

equipments, tools, plants & machineries required for the job, all

complete as per direction of Engineer-in-charge, upto 90 metre

depth below ground level.

23.1.1 All types of soil

Supplying, assembling, lowering and fixing in vertical position in

bore well, unplasticized PVC medium well casing (RMS) pipe of

2 23.4 required dia, conforming to IS: 12818, including required hire and

labour charges, fittings & accessories etc. all complete, for all

depths, as per direction of Engineer -in-charge.

23.4.2 150mm nominal size dia metre 90.00 807.45 785.65 70,708.50

Gravel packing in tubewell construction in accordance with IS:

4097, including providing gravel fine/ medium/ coarse, in

required grading & sizes as per actual requirement, all complete

as per direction of Engineer-in-charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, having thermal stability for hot & cold water supply

4 18.9 including all CPVC plain & brass threaded fittings This includes

jointing of pipes & fittings with one step CPVC solvent cement,

trenching, refilling & testing of joints complete as per direction

of Engineer in Charge.

Development of tube well in accordance with IS : 2800 (part I)

and IS: 11189, to establish maximum rate of usable water yield

without sand content (beyond permissible limit), with required

capacity air compressor, running the compressor for required

time till well is fully developed, measuring yield of well by "V"

5 23.12 notch method or any other approved method, measuring static hour 24.00 1,085.05 1,055.75 25,338.00

level & draw down etc. by step draw down method, collecting

water samples & getting tested in approved laboratory, i/c

disinfection of tubewell, all complete, including hire & labour

charges of air compressor, tools & accessories etc., all as per

requirement and direction of Engineer-in-charge.

COST OF 1 BORE WELL 2,24,735.50

SECTION- VI TUBE WELL INSTALLATIONS (NON-SCHEDULED ITEMS)

S.I.T.C. 2.0 HP Submerssible Pump (vertical type- suitable for

7 MR suctioning water from Bore-well), including necessary cables, Each 1.00 73,387.00 73,387.00 73,387.00

wirring etc all complete

COST OF 1 BORE WELL 73,387.00

Digitally signed by PRIYA

Construction of Officie Building for the Institute of Company Secretaries of India (ICSI) at Raipur (CG).

Room Total Rate I/C

S.No. Location Item Name Specification Size Unit Total Amount Refrence Image

S.No. Location Item Name Specification Size Unit Total Amount Refrence Image

Supplying and placing in position of main Table as per drawing. Modular tables size 2400mm(L) x

750mm(D) x 750mm(H).The Table top made out of 25mm thk prelam particle board with 2mm thk pvc edge

banding . The side panel & modesty panel made up of 18mm thick pre-laminated particle board .The working

edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot

temperature. Provision of 3 drawer mobile pedestal (size:- L-400mm x D-450mm x H-600mm) attached to

the table top. Pedestal Unit have a combination of 2 drawer & one filing drawer. The pedestal storage unit Main Table - W

shall be made of 18 mm thick prelaminated Particle board with provision of handles & central Locking 2400 X D 750 X H

Chairman Main Table & Chairman

1 arrangement. The table have a provision of Side Storage of size 1200mm L x 600mm D x 750mm Ht. 750 / Side Unit - 1 Each 45,430 45,430

Office Side Unit Office

Storage Top made out of 25mm thick pre laminated particle board and rest all storage to be made out of 18 W 1200 X D 600

mm thick prelaminated particle board . All exposed edges shall be provided with machine pressed 2 mm thick X H 750

PVC lipping glued with hot melt EVA glue. Storage having provision of 3 drawer unit, one openable shutter,

one open storage with handle & central locking provision. The unit should be complete as per image, and

specification under the guidance of Engineer in charge. ( ± 5% Varaition allowed). The manufacturer should

have ISO - 9001:2015, ISO - 14001:2015, ISO - 45001:2018, ISO - 50001:2018, Green Pro, AIOTA BIFMA

Compliant, BIFMA Membership, GRIHA, ZED GOLD, IGBC & IDM Certifiactes.

Supplying & Placing Meeting table in completely knock down conditions with an overall size 2400mm X

900mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing

structure constructed with the help of minifix dowels and pins. The table top shall be made up of 36mm thick

Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade.

The table top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of

impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding

machine at 200 degree celsius. The table shall be supported on particle board base gable end. The end wall of

the table on the side shall be topped by gable end with gable and front strip. It should be made up of 25mm

Chairman Chairman L 2400 X W 900

2 Meeting Table thick Pre-laminated particle board and profile shall be in linear shape and other edges sealed with gable end 1 Each 37,170 37,170

Office Office X H 750

front aluminium strip. The table shall be clad with 18mm thick modesty panel which provide structural

support for the table. It should be 18mm thick pre- laminated particle board with appropriate PVC edge

banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor.

The table connections have to be made in such a way that no gap should be in between. Above the top 02 Nos.

Access Flap, Below the top CRCA powder coated cable tray for wire provision & Vertical riser for wire rising

from ground. ( ± 5% Varaition allowed). The manufacturer should have ISO - 9001:2015, ISO - 14001:2015,

ISO - 45001:2018, ISO - 50001:2018, Green Pro, AIOTA BIFMA Compliant, BIFMA Membership, GRIHA,

ZED GOLD, IGBC & IDM Certifiactes.

Supplying and placing single seater sofa that shall be constructed from natural hard wood and commercial

plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa

shall have spring attached and also be padded separately. The frame shall be padded with high resilience

polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided

padded with high resilience polyurethane foam having density 32Kg/m³. The complete structure shall be

Chairman Chairman

3 3 Seater Sofa upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall have Gold 3 Seater Sofa 1 Each 38,350 38,350

plated 75 mm Height. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat

height = 430±10 mm, overall width = 1900±10 mm, overall depth = 860±10 mm & overall height = 870±10

mm. ( ± 5% Varaition allowed). The manufacturer should have ISO - 9001:2015, ISO - 14001:2015, ISO -

45001:2018, ISO - 50001:2018, Green Pro, AIOTA BIFMA Compliant, BIFMA Membership, GRIHA, ZED

GOLD, IGBC & IDM Certifiactes.

Digitally signed by PRIYA

Construction of Officie Building for the Institute of Company Secretaries of India (ICSI) at Raipur (CG).

Room Total Rate I/C

S.No. Location Item Name Specification Size Unit Total Amount Refrence Image

S.No. Location Item Name Specification Size Unit Total Amount Refrence Image

Overall Size : (L)900mm X (W)450mm X (H)450mm

Providing, and placing in position of rectangular Center table Dimension (L) 900X (W)450mm X

(H)450mm . The center table top made out of 50mm thk solid wood (superior quality Teak wood) with

Glass of 08 mm thk tempered with pu polish in matt finish and legs are also made out of solid superior

Chairman Chairman quality teak wood of size: 50mm x 50mm thk with pu polish in matt finish. The centre table having a

Office Office provision of shelf of 25mm thick MDF with board superior quality teak Veneer with with pu matt

polish . The teak wood shall be KILN dried season .The pu polish treatment on exposed surface of solid

wood should be done in pu matt polish. ( ± 5% Varaition allowed). The manufacturer should have ISO -

9001:2015, ISO - 14001:2015, ISO - 45001:2018, ISO - 50001:2018, Green Pro, AIOTA BIFMA Compliant,

BIFMA Membership, GRIHA, ZED GOLD, IGBC & IDM Certifiactes.

Supplying, and placing in position of 360 degree revolving High back chair as per Image. This contemporary

chair comprises of luxurious double padding cushion with a central indent that provides lower back support

for proper posture and comfort. The central panel in the backrest is neatly stitched with a soft seat cushion

finished in the same black leatherette. The Chair nestles on a shiny chrome vaulted base with nylon castors.

the shiny armrests come adeptly padded for comfort. Material & Subtype:Leatherette, Colour & Colour

Family:Black ,Dimension(W)625mm X (D)490mm X (H)1210mm, Back Type:High Back, Base:Chrome

Base, Base Type:Revolving, Maximum Seating Height:25", Minimum Seat Height:21.25",Function:

Chairman High Back Chairman

5 Revolving::Pneumatic Height Lift::Tilt Tension Control::Centre Tilt, Locking Mechanism:Centre Tilt. The High Back Chair 2 Each 17,110 34,220

Office Chair Office

pneumatic height adjustment shall have adjustment stroke of 100 mm and shall be operated at 30kgs

extension force.The Seat & back are made up of 12mm thk hot pressed plywood upholstered with PVC with

polyurethane foam, chair seat has foam of density 32-35 kg/m3 . The backrest has a foam of 28kg/m3. The

unit should be complete as per image, and specification under the guidance of Engineer in charge. ( ± 5%

Varaition allowed). The manufacturer should have ISO - 9001:2015, ISO - 14001:2015, ISO - 45001:2018,

ISO - 50001:2018, Green Pro, AIOTA BIFMA Compliant, BIFMA Membership, GRIHA, ZED GOLD, IGBC

& IDM Certifiactes.

Supplying, and placing in position of 360 degree revolving medium back chair as per Image. A contemporary

design with an all black finish, the chair is a staple in every office setting. A double padded cushion encased

in an all black premium leatherette makes for one comfy seat. The side padding and the headrest sit snugly

providing added lumbar support to the user. Material & subtype:Premium Leatherette, Colour & Colour

Family:Black, Dimension(W)625mm X (D)490mm X (H)1135mm,Back Type:medium back, Base:Chrome

Chairman Medium Back Chairman Base, Maximum Seating Height:19",Finish:Matte.The pneumatic height adjustment shall have adjustment Medium Back

Office Chair Office stroke of 100 mm and shall be operated at 30kgs extension force.The Seat & back are made up of 12mm thk Chair

hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35

kg/m3. The backrest has a foam of 28kg/m3. The unit should be complete as per image, and specification

under the guidance of Engineer in charge. ( ± 5% Varaition allowed). The manufacturer should have ISO -

9001:2015, ISO - 14001:2015, ISO - 45001:2018, ISO - 50001:2018, Green Pro, AIOTA BIFMA Compliant,

BIFMA Membership, GRIHA, ZED GOLD, IGBC & IDM Certifiactes.

Digitally signed by PRIYA

Construction of Officie Building for the Institute of Company Secretaries of India (ICSI) at Raipur (CG).

Room Total Rate I/C

S.No. Location Item Name Specification Size Unit Total Amount Refrence Image

S.No. Location Item Name Specification Size Unit Total Amount Refrence Image

Supplying & Placing workstation table in completely knock down conditions with an overall size 900mm X

900mm X 1050mm that is to be assembled at site. The top shall have the size 900mm X 900mm made up of

sharing base 25mm thick Pre-laminated particle board of grade II of IS 12823 with one side laminate and

finish as per approved shade. The profile of the top shall be in square shape and the edges shall be sealed with

2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the

assistance of edge banding machine at 200 degree celsius. The workstation shall have desking base system

with overall height 1050mm. Glass screen is made of 8mm thick sandwich glass of height 300mm. The top

7 Library Library Table Library 900 X 900 X 750 5 Each 12,390 61,950

shall be supported on MS Powder Coated Metal pipe with cross-section area 40mm X 20mm and powder

coated pipe strip having size 100mm X 30mm X 15mm. The table understructure shall have powder coated C

shape leg having size with cross-section 60mm X 30mm of thickness 1.6mm.Horizontal Power Management

shall be given under flip on metal cable tray, where switch plate shall be mount and vertical metal riser for

vertical wire trucking. ( ± 5% Varaition allowed). The manufacturer should have ISO - 9001:2015, ISO -

14001:2015, ISO - 45001:2018, ISO - 50001:2018, Green Pro, AIOTA BIFMA Compliant, BIFMA

Membership, GRIHA, ZED GOLD, IGBC & IDM Certifiactes.

Providing and supplying visitor chair with ergonomic design for user comfort. The seat and back shall be

made of hot pressed commercial plywood padded with high resilience polyurethane foam having density

40Kg/m³ in seat and 32kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick.

The backrest of the chair shall be made by keeping the natural curvature of the spine for lumbar support with

the assistance of cushion. The armrest shall be of chrome plated frame padded with cushion with leatherite

covering on top. The frame structure shall be cantilever support type made up of MS/CRCA chrome plated Medium Back

8 Library Library Chair Library 10 Each 7,434 74,340

pipe having cross section 40mm x 20mm. There shall be co-polymer polypropylene shoe provided at the base Chair

to avoid scratches on the floor as well as uneven surfacing. The seat size shall be 500±10 mm(W) X 500±10

mm(D) and back size shall be 490±10 mm(W) X 550±10 mm(H) from seat & overall height = 960±10 mm,

overall width = 600±10 mm & overall depth = 670±10 mm. ( ± 5% Varaition allowed). The manufacturer

should have ISO - 9001:2015, ISO - 14001:2015, ISO - 45001:2018, ISO - 50001:2018, Green Pro, AIOTA

BIFMA Compliant, BIFMA Membership, GRIHA, ZED GOLD, IGBC & IDM Certifiactes.

Providing, supplying and placing an open display book racks. The overall size of the rack shall be 900mm

(W) X 300mm (D) X 1800mm (H). The rack shall be supplied with 4 nos. of adjustable shelves i.e. 5 loading

levels. Rack, side panel, skirting shall be made of 0.8mm thick high yield strength CRCA sheet of grade 'D'

confirming to IS: 513. Side and top shall be covered with 18mm thick Pre-laminated particle board of grade II

of IS 12823. The edges of the board shall be sealed with 2mm thick PVC edge banding. The add-on units can

be stacked width wise to form a bank of racks having common panel. Back panel up to the bottom of third

One Side Book rack shall have additional rigidity. The shelves shall have folded constructions which have intrinsic rigidity

9 Library Library 900 X 300 X 1800 6 Each 21,830 1,30,980

Rack and high load carrying capacity. Uniformly distributed load capacity per each shelf shall be 80 kg maximum.

Each rack shall be provided with stiffener at bottom for strength. Label holder & range indicators on each

main unit for inserting labels. All steel components shall be epoxy polyester powder coated to the thickness of

40-60µ. Adjustable leveler shall be provided with metal insert to resist scratches on the floor and also level &

support structure. ( ± 5% Varaition allowed). The manufacturer should have ISO - 9001:2015, ISO -

14001:2015, ISO - 45001:2018, ISO - 50001:2018, Green Pro, AIOTA BIFMA Compliant, BIFMA

Membership, GRIHA, ZED GOLD, IGBC & IDM Certifiactes.

Digitally signed by PRIYA

Construction of Officie Building for the Institute of Company Secretaries of India (ICSI) at Raipur (CG).

Room Total Rate I/C

S.No. Location Item Name Specification Size Unit Total Amount Refrence Image

S.No. Location Item Name Specification Size Unit Total Amount Refrence Image

Providing and placing, Main Table(W) 1500 X (D)750 X(H) 750 is completely made up of particle board conforming

to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk Pre-laminate particle boards. Table top is

supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding

& sealed edges are in 0.8mm thk PVC edge banding. Side table (W) 900 X (D) 450 X (H) 750 top on User side and Main Table - W

rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top 1500 X D 750 X H

Incharge Main Table & Incharge

10 is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge 750 / Side Unit - 1 Each 31,860 31,860

Cabin Side Unit Cabin

banding & sealed edges are in 0.8mm thk PVC edge banding.Pedestal unit of size 400mm L x 450mm D x 680mm W 900 X D 450 X

made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 H 750

Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. ( ± 5% Varaition allowed).

The manufacturer should have ISO - 9001:2015, ISO - 14001:2015, ISO - 45001:2018, ISO - 50001:2018, Green Pro,

AIOTA BIFMA Compliant, BIFMA Membership, GRIHA, ZED GOLD, IGBC & IDM Certifiactes.

Supplying, and placing in position of 360 degree revolving high mesh back chair as per Image. Styled for the

contemporary office space the chair boasts of a curved backrest with a central console for lower back support. this

helps to improve posture and provides comfortable seating all day long. The chair is fixed to a sleek chrome vaulted

base with its individual prongs powered by nylon castors. A complete executive office chair, Jordon will bring you

comfort like never before. Material & Subtype:Mesh, Colour & Colour Family:Black Dimension(W)640mm X

(D)480mm X (H)1240mm, Back Type:High Back, Base:Chrome Base, Base Type:Revolving, Maximum Seating

Incharge High Back Incharge

11 Height:1240mm, Minimum Seat Height:1140mm, Function-Revolving::Pneumatic Height adjustment::Tilt Tension High Back Chair 1 Each 8,496 8,496

Cabin Chair Cabin

adjustment::Synchro tilt locking: PU adjustable handle : adjustable lumbar support .The pneumatic height adjustment

shall have adjustment stroke of 100 mm and shall be operated at 30kgs extension force. The Seat are made up of

12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35

kg/m3 . The unit should be complete as per image, and specification under the guidance of Engineer in charge. ( ± 5%

Varaition allowed). The manufacturer should have ISO - 9001:2015, ISO - 14001:2015, ISO - 45001:2018, ISO -

50001:2018, Green Pro, AIOTA BIFMA Compliant, BIFMA Membership, GRIHA, ZED GOLD, IGBC & IDM Certifiactes.

Supplying, and placing in position of 360 degree revolving medium mesh back chair as per Image. Styled for the

contemporary office space the chair boasts of a curved backrest with a central console for lower back support. this

helps to improve posture and provides comfortable seating all day long. The chair is fixed to a sleek chrome vaulted

base with its individual prongs powered by nylon castors. A complete executive office chair, Jordon will bring you

comfort like never before. Material & Subtype:Mesh, Dimension:(W)610mm X (D)470mm X (H)1040mm, Back

Incharge Type:Medium Back, Base:Chrome Base, Base Type:Revolving, Maximum Seating Height:1040mm, Minimum Seat

Medium Back Incharge Medium Back

12 Cabin & Height:940mm, Function:Revolving::Pneumatic Height adjustment::Tilt Tension adjustment::Synchro tilt Locking:PU 4 Each 8,024 32,096

Chair Cabin Chair

Workstaions adjustable handle : adjustable lumbar support . The pneumatic height adjustment shall have adjustment stroke of 100

mm and shall be operated at 30kgs extension force. The Seat are made up of 12mm thk hot pressed plywood

upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3.The unit should be

complete as per image, and specification under the guidance of Engineer in charge. ( ± 5% Varaition allowed). The

manufacturer should have ISO - 9001:2015, ISO - 14001:2015, ISO - 45001:2018, ISO - 50001:2018, Green Pro, AIOTA

BIFMA Compliant, BIFMA Membership, GRIHA, ZED GOLD, IGBC & IDM Certifiactes.

Digitally signed by PRIYA

Construction of Officie Building for the Institute of Company Secretaries of India (ICSI) at Raipur (CG).

Room Total Rate I/C

S.No. Location Item Name Specification Size Unit Total Amount Refrence Image

S.No. Location Item Name Specification Size Unit Total Amount Refrence Image

Providing and placing workstation table in completely knock down conditions with an overall size 1320mm X 660mm

X 1200mm that is to be assembled at site. The work top shall have the size 1200mm X 600mm made up of 25mm thick

Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The

profile of the top shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable

PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree

celsius. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 525mm X

350mm. The trey shall be operated on keyboard channel. The workstation shall have panel based partition of 60 mm 18,644 37,288

thick with overall height 1200mm. The partition shall be linear in profile and provided in the front side of user as well

as on the both sides of the user. The top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of

aluminium extrusions (pre-treated) and duly powder coated with 40µ-60µ thick. The trims shall have the size 60mm X

19mm with 1.5mm thick covered with Die cast end caps on joints 2 ways, 3 ways & 4 ways (L-cover for corner, T-

cover for middle section wherever required). The aluminium raceway shall be situated below the worktop with an

overall size 116mm(H) X 60mm(D) with 1.4 mm cover thickness and 2mm back thickness as per requirement of

inlaying the electrical management and carrying the wire horizontally. The exposed vertical and horizontal faces of the

frames shall be snap fitted with trims. There shall be soft-board (with fabric) and marker board provided at front of the

user. Laminated top tile and bottom tile shall be situated at both sides of the user and below the work top respectively.

13 Workstations Workstation Workstations 1320 X 600 x 750 2 Each

The Partition shall have concealed wire management capabilities and should be engaged for responsive and safe

operations of power, telecommunications and data (LAN) and has separate components for electrical, data and

telephone cables having adequate capability of both the vertical and horizontal wire movements. Slots/cut-outs should

be given on raceways to fix all electrical and data points. Zinc coated small top support brackets shall be fixed on the

partition for table top support. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting

shall be situated at bottom. Adjustable leveller shoe shall be provided at bottom of the partition to avoid scratches on

the floor. Fixed type pedestal shall be provided with an overall size 400mm X 450mm X 725mm. The pedestal shall be

made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and

drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The

drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing - -

channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be

synchronized lock with one single key. To protect the wall from kicks, abrasion and serve as a decorative moulding,

skirting shall be provided at bottom. A nylon castor based CPU unit shall be provided with an overall size 468mm X

284mm with 18mm thick Pre-laminated particle board. ( ± 5% Varaition allowed). The manufacturer should have ISO -

9001:2015, ISO - 14001:2015, ISO - 45001:2018, ISO - 50001:2018, Green Pro, AIOTA BIFMA Compliant, BIFMA

Membership, GRIHA, ZED GOLD, IGBC & IDM Certifiactes.

Supplying & placing storage unit with an overall size 1500mm X 450mm X 1200mm. The storage shall be made up of

Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top

shall be made up of 25mm thick and other parts like side, back, shutter, facia, skirting shall be 18mm thick. The edges

shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the

assistance of edge banding machine at 200 degree Celsius. The storage shall be supplied with 2 nos. of shelves. Door

shutters shall be provided for opening and closing the storage. The shutter shall be operated with concealed crank hinge

Low Ht 1500 X 450 X

14 Workstations Workstations and die cast handle as well as proper locking arrangement. To protect the wall from kicks, abrasion and serve as a 4 Each 7,670 30,680

decorative moulding, skirting shall be provided at bottom. There shall be buffers provided at the bottom to avoid

scratches on the floor. . The boards used should meet international standards of quality and safety, Indian standard IS

12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of elasticity bending tested as

per IS 2380. ( ± 5% Varaition allowed). The manufacturer should have ISO - 9001:2015, ISO - 14001:2015, ISO -

45001:2018, ISO - 50001:2018, Green Pro, AIOTA BIFMA Compliant, BIFMA Membership, GRIHA, ZED GOLD,

IGBC & IDM Certifiactes.

Digitally signed by PRIYA

Construction of Officie Building for the Institute of Company Secretaries of India (ICSI) at Raipur (CG).

Room Total Rate I/C

S.No. Location Item Name Specification Size Unit Total Amount Refrence Image

S.No. Location Item Name Specification Size Unit Total Amount Refrence Image

Supplying & placing storage unit with an overall size 1500mm X 450mm X 2100mm. The storage shall be made up of

Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top

shall be made up of 25mm thick and other parts like side, back, shutter, facia, skirting shall be 18mm thick. The edges

shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the

assistance of edge banding machine at 200 degree Celsius. The storage shall be supplied with 4 nos. of shelves. Door

Incharge Incharge shutters shall be provided for opening and closing the storage. The shutter shall be operated with concealed crank hinge

15 Cabin & Full Ht Storage Cabin & and die cast handle as well as proper locking arrangement. To protect the wall from kicks, abrasion and serve as a 2 Each 17,700 35,400

Workstaions Workstaions decorative moulding, skirting shall be provided at bottom. There shall be buffers provided at the bottom to avoid

scratches on the floor. . The boards used should meet international standards of quality and safety, Indian standard IS

12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of elasticity bending tested as

per IS 2380. ( ± 5% Varaition allowed). The manufacturer should have ISO - 9001:2015, ISO - 14001:2015, ISO -

45001:2018, ISO - 50001:2018, Green Pro, AIOTA BIFMA Compliant, BIFMA Membership, GRIHA, ZED GOLD,

IGBC & IDM Certifiactes.

Supplying & placing in position chair with MOULDED PLY SHELL: The seat & back is made up of moulded ply in

Veneer or Laminate finish with writing pad.

Shell size - 420 mm (W) X 410 mm (D) X 440 (H) X Thickness 12 mm.

UNDER STRUCTURE:

Multipurpose Writing Arm Multipurpose The Understructure is made up of dia. 25.4 ±0.3mm. x 1.6mm thick M.S. E.R.W. tube supporting frame in C-shape and Medium Back

Room Chair Room welded to 250mm x 250mm x Chair

2mm thick MS plate welded at seat level to support seat with necesary fixing arrangement . The framework shall be

epoxy coated having DFT 50-60 Micron. The leg at bottiom shall be fitted to rubber bush. ( ± 5% Varaition allowed).

The manufacturer should have ISO - 9001:2015, ISO - 14001:2015, ISO - 45001:2018, ISO - 50001:2018, Green Pro,

AIOTA BIFMA Compliant, BIFMA Membership, GRIHA, ZED GOLD, IGBC & IDM Certifiactes.

Digitally signed by PRIYA