CLEANING AND REPAIRS/RENEWAL OF SEWAGE LINES, DESILTING OF SEPTIC TANK IN AREA II OF AGE B/R C UNDER THE AOR OF GE DEOLALI

Amount

Dewatering of following including disludging of sluldge at bottom in foul condition including taking out other dirty & filthy materials from manhole & septic tanks by sewage pump or manually using buckets/baskets, lifting the same upto 4.50M depth of tank/MH and removing to out side MD land including cleaning/clearing for following :-

(a) Manhole of any dimension upto 1.5 Mtr deep

(b) Manhole of any dimension exc 1.5 Mtr but n exc 3 Mtr deep.

(c) Septic Tank up to 10 User capacity.

(d) Septic Tank up to 50 User capacity.

(e) Septic Tank exc 50 and n exc 100 users capacity.

(f) Septic Tank exc 100 and n exc 200 Users capacity.

Cleaning of SWG/RCC Sewage line of 75 to 200mm bore dia of pipe of foul condition by rodding the drain/sewage line using flexible rod/suitable device or by any other means for removing blockage from sewar line, mud, silt and any other debries obtained from sewage line with water to remove blockage and cleaning the entire rubbish, sludge etc and burrying the material obtained from sewage line including all precautionery and safety measures etc complete all as specified and directed.

Removing blockage from water closet, floor or gully or Nahani Trap traps and bends by rodding thoroughly and pouring water under pressure and Cleaning, clearing the drainage to efficient and Smooth flow of sludge/waste water all as specified and directed by Engineer-in-Charge.

NOTE FOR SL NO. 1(a)to(f), 2 &3 :- (i) Contractor's supervisor will report on all working days along with Two safai wala and Printed contractor's firm name complaint slip book at 0830 hrs at B/R Haig Line to receive complaints for blockage and to submit completion report on the same day by 1700 hrs. (ii) Printed complaint slip book area wise as per format approved by Engineer-in-Charge shall be provided and maintained by contractor. (iii) Rate quoted above shall be deemed to incl the cost of T&P, equipment, safety device etc alongwith sufficient labour to full fill the requirement to the entire satisfaction of Engineer-in-charge. (iv) if there is any major blockage in sewer line/septic tank for which additional Safaiwalas and special T&P is required same shall be provided by contractor without any extra cost to Govt. therefore contractor is adviced to visit the site before quoting the rates in tender. (v) In the event he fails to attend the complaint recovery @ Rs. 1000 per day shall be effected from the amount due to the contractor.

Cutting out of shrubs, kerbs and small plants of stem girth n.exc 30CM measured 1M above average ground level including cutting of grass & removing the unserviciable material like branches, leaves, grass & garbage to clear the alignment of existing sewage/drainage line to make site workable condition & making good the disturbed ground complete all as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in soft soil complete all as specified and directed.

All as per Sl item No. 5 above but exc 1.5m depth and n exc 3.0m depth and getting out hard/dense soil complete all as specified and directed.

Returning, filling in soft/loose/hard/dense soil including spreading, levelling, watering & well ramming in layers n.exc 25cm complete all as specified and directed.

Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick spread, levelled and rammed including watering

Removing excavated material (surplus soil) to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed by Engineer-in-charge.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar, Dia of pipe 150mm bore complete all as specified and as directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar, Dia of pipe 100mm bore complete all as specified and as directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar, Dia of pipe 300mm bore pipe complete all as specified and as directed.

M&L for 150mm Inner dia DWCPE (SN8) as per IS -16098 (part-III) drain pipes laid in trenches on moorum bed including jointing and testing complete all as specified and directed by Engineer-in-charge. Note : Moorum shall be measured separately

M&L for 100mm Inner dia DWCPE (SN8) as per IS -16098 (part-III) drain pipes laid in trenches on moorum bed including jointing and testing complete all as specified and directed by Engineer-in-charge.

M&L for 300mm Inner dia DWCPE (SN8) as per IS -16098 (part-III) drain pipes laid in trenches on moorum bed including jointing and testing complete all as specified and directed by Engineer-in-charge.

M&L for 150mm bore Reinforced concrete pipes single socketed, class NP-2, laid and jointed, complete all as specified and as directed.

M&L for cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in concrete bed to drain pipes including packing under & haunching against the sides of pipes after they are laid & tested for 150mm & bore pipe, complete all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed.

M&L for cement concrete Type 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundations, haunching and packing of pipe complete all as specified and as directed.

M&L for cement concrete Type B1 1:2:4 (20 mm graded aggregate) as in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs/benching and the like including weathering, slightly rounded for chamfered angles and throating including demolition of cement concrete (unreinforced) is ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of brick work or stone / boulder masonry built in cement mortar including all quoins, arches, pillars etc.

M&L for Autoclaved aerated concrete (AAC blocks (light weight) for masonry fixed with ready mixed jointing mortar complete all as specified and as directed. Make/Brand of ready mixed jointing mortar: Shall be 'Speed Dry Mix'/'DUBOUND'/MAGIC BOND'/'BUILDWELL'. Make/Brand of ACC block : 'AEROCON'/Ecolite ISI marked Grade-I as approved by GE.

M&L for fly ash brick work with old size sub class 'B' bricks straight or curved on plan exc. 6m mean radius and built in CM 1:6 etc complete all as directed.

M&L except brick work with sub class 'B' brick straight or curved on plan exc 6m mean radius with old size bricks in CM 1:6 complete all as specified and directed.

Taking down cement plaster any description on brick or stone walls etc including racking out joints hacking for key scrubbing down with water etc complete all as specified and as directed.

M&L for rendering 15mm thick External plaster with ready mix plaster on brick or concrete surfaces, complete all as specified and as directed. Make/Brand : ACCs 'ACCOPLAST', C K Birla's "AEROCEN, Magic Plast, Speed Dry Mix's ' ECO PLASTER'

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for Note- Rate includes for reinforcement cutting as required to facilitate demolition.

M&L Pre-cast reinforced cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate in manhole cover/slabs and placing in position including necessary form work in CM 1:6 complete all as specified and directed.

S&F for mild steel TMT bars 8mm to 10mm dia cut to length, bent to shape required including cranking, bending, spirally for hooping columns, hooking ends & binding with & including MS wire (annealed) not less than 0.9mm dia of or securing with clips complete all as specified and as directed.

Dismantling of PVC Pipes with fittings upto 75mm to 110mm dia complete all as specified and as directed.

S&F for PVC (SWR) pipe 110 mm dia single socketed in any length with rubber ring jointed level fixed to walls complete all as specified and as directed.

All as per Item No. 31 above but except pipe.

S&F for PVC (SWR) pipe 75 mm dia single socketed in any length with rubber ring jointed level fixed to walls complete all as specified and as directed.

All as per Item No. 33 above but except pipe.

S&F for PVC (SWR) bends with access door 110 mm dia complete all as specified and as directed.

S&F for PVC (SWR) bends with access door 75 mm dia complete all as specified and as directed.

S&F PVC (SWR) plain bend 110 mm dia complete all as specified and as directed.

S&F PVC (SWR) plain bend 75 mm dia complete all as specified and as directed.

S&F PVC (SWR) branch piece single or double 'Y' equal or unequal with access door 110 mm dia complete all as specified and as directed.

S&F PVC (SWR) branch piece single or double 'Y' equal or unequal with access door 75 mm dia complete all as specified and as directed.

S&F PVC (SWR) vent cowl 110 mm dia complete all as specified and as directed.

S&F PVC (SWR) vent cowl 75 mm dia complete all as specified and as directed.

S&F in repairs 75mm bore PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F in rep vitreous china squatting Pan “Orissa” Pattern, of size 580mm x 440mm white with integral foot rests and trap (excluding flushing cistern and flush pipe) including provn of cement concrete bedding complete as fixed complete all as specified.

M&L for non skid Ceramic dark coloured tiles 6-7mm thick (squar/ ractangular) area of each tiles exc 0.06 Sqm but not exc o.11 Sqm, in floor including 15mm thick screed bedding in CM (1:6) and jointing with neat cement slurry and pointing with white/coloured cement to match the surfaces including demolition of stone slabs and tiles laid, bedded and pointed in any mortar of any description or thickness in floors, aprons etc.complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

M&L for joint free coloured glazed ceramic tiles in vertical surface of size 300X 600X 7mm thick of different shade colour and pattern as approved, over and including 10 mm thick rendering in CM 1:4 as backing coat finished to receive wall tiles, set and jointed in neat cement slurry and pointed in white or colour cement to match etc complete all as directed and specified.

M&L for joint free coloured glazed ceramic tiles in vertical surface of size 300X 450X 7mm thick of different shade colour and pattern as approved, over and including 10 mm thick rendering in CM 1:4 as backing coat finished to receive wall tiles, set and jointed in neat cement slurry and pointed in white or colour cement to match etc complete all as directed and specified.

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate ) as in subase finished to receive floor treatment etc complete all as directed.

M & L for chequered cement concrete tiles rubber moulded , 30cm x 30cm x 25mm thick confirm to IS 13801-1993 , set jointed & pointed in neat cement slurry with grey cement and pigment in floors incl Screed bed or bedding layer of mortar 15 mm thick in CM 1:6 for laying floor finishes complete all as specified and directed

S&L machine pressed precast concrete interlocking paver block rubber moulded, any shape and size confirming ti IS-15658-2006 of 60mm thickness grey cement and with pigment , M-35 grade incl 30mm thick Sand filling to under interlocking tiles complete all as specified and directed.

Demolition of stone slabs, paving stones and tiles of any description and thickness in floors, aprons, laid, bedded and pointed in any mortar complete all as specified and directed.

M & L for Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including rubbing and polishing complete all as specified.

M & L for 16-18mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. including Screed bed or bedding layer of mortar 20 mm thick for laying floor finishes complete all as specified.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

S&F vitreous china single piece EWC bowl with cistern for extended wall hung WC of Size: 380x630x770 mm, PP Soft Seat cover, Hinges, Fixing Accessories, Accessories Set, and dual Cistern fittings, P trap-180mm complete all as specified and directed Make Jaquar cat part No CNS-WHT-353SPPZ or CNS-WHT-755S220SPPZ Bowl with cistern for or equivalent in kohlar, grohe and Roca

S&F vitreous china Sensor Urinal of Size: 340x265x560 mm,wall hung urinal back inlet urinal with DC sensor, removable ceramic waste plug with water seal complete all as specified and directed Make cat part No Aurore of Somany or equivalent in Jaquar, grohe and Roca

S&F in repairs glazed earthen ware viterous china wash down water closet(pedestal pattern) white coloured with and including plastic water closed seat, white, closed pattern with recessed bottom, and cover and mild steel chromium plated hinging device etc complete all as directed. Make somany Cat Part No. SMART EWC P or Equivelent in Cera/Hindware/Parryware

S&F in repair vitreous china Wash Basin counter Top 600x400x185mm including stainless steel bottle trap and 40 mm dia GI pipe up to Floor trap complete all as specified and directed by Engr-in-Charge Make : Cat Part No SLS-WHT-6601 & ALD-769L250x190 of Jaquar or equivalent in kohlar, grohe and Roca

S&F in repairs glazed earthen ware viterous china wash basin white coloured (flat back or angle back type), size 550x400 mm and including CI brackets, outlet of 32 mm bore HDPE outlet pipe with necessary fittings ,32 mm bore brass CP waste couplings and bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed etc complete all as directed.

S & F in repair 15 mm bore, fancy type, bib taps, long body, cast copper alloy, 15mm bore with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by Engr-in-Charge. Make : Cat Part No FLR- 5047 N of Jaquar or equivalent in kohlar, grohe and Roca

S & F in repair 15 mm bore, fancy type, angular valve, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed by Engr-in-Charge. Make : Cat Part No FLR-5053 N of Jaquar or equivalent in kohlar, grohe and Roca

S&F for 15mm bore, 450mm long, PVC connections with brass unions internally threaded both ends complete fixed to iron pipe at both ends as fixed in repairs complete all as specified and as directed. Make : Prayag or equivalent

S&F in repair Health Faucet (ABS Body) with 1.20 M Long PVC Tube and wall Hook screwed down to GI pipe or union/angle valve complete all as specified and directed by Engr-in-charge Make Jaquar Code No- ALD-CHR-583 or equivalent in kohlar, grohe and Roca

S & F in repair CP, soap dish complete all as specified and as directed by Engr-in-Charge. Make Jaquar Code No- AKP -35731 P or equivalent in kohlar, grohe and Roca

S&F in repair Maze Overhead Shower 200X200mm Square Shape Single Flow (Body & Face Plate Stainless Steel with Chrome Finish) with Rubit Cleaning System including showe arm of size 400x25x25mm sq shape for wall mounted showers with flange, fixing to steel pipe or union complete all as specified Make Jaguar (Cat part No : OHS-1619 & SHA 455L400 or equivalent in kohlar, grohe and Roca

S&F sheet glass corner shelf wall mounted shelf assembly consisting of 5mm thick sheet glass 220mmX220mm size with chromium plated bracket guard and railing 50mm high complete all as specified and as directed. Cat Part no CAN -1173 of jaquar or equivenet in Kohlar, grohe and Roca

S&F in repair Towel Rack with Lower Hanger (Stainless Steel) with hook complete all as specified and directed Make Jaguar (Cat Part No: AHS-1581H) or equivalent in kohlar, grohe and Roca

S&F in repair brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges.

S & F in repair for 15 mm bore, fancy type, Wall Mixer 3-in-1 System with Provision for both Hand Shower and Overhead Shower Complete with 115mm Long Bend Pipe, Connecting Legs & Wall Flange and including Telephone Shower and shower stand complete all as specified and as directed by Engr-in-Charge Make Jaguar Cat Part No: FLR-5281N, Hand shower HSH 1715, flexible tube SHA-549D12 or equivalent in kohlar, grohe and Roca

S&F in repair 15mm dia brass chromium plated Central Hole Basin Mixer single lever tall boy with 150mm extension body fixed spout without popup waste system with 600mm long braided hoses for mixing hot and cold water, screwed down for 15 mm dia bore GI Pipe complete all as specified and directed. Make Jaguar Cat Part No: FLR-5005NB or equivalent in kohlar, grohe and Roca

S&F in repair 15mm dia brass chromium plated two way bib cock with long flange screwed down for 15 mm dia bore GI Pipe complete all as specified and directed. Make Jaguar Cat Part No: ARI 39041 or equivalent in kohlar, grohe and Roca

M&L Soakage wells of size 1.80m Dia and depth 3.00m excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size

M&L Soakage wells of size 2.40m Dia and depth 3.00m excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size

M & L for Construction of septic tank including excavation in any type of strata, foundation in PCC 1:2:4 type B-1 ( using 20 mm graded stone aggregate ) brick work in CM 1:4, RCC Slab cover including RCC Precast manhole cover having 6mm plate embedded all around/fibre reinforced cover with angle iron frame vent shaft and sludge chambers complete for 25 users all as specified and shown on Drg Nos CEPZ/ 88 TD /17-M Sheet Nos 1/4; 2/4 ,3/4 and 4/4 dated 01.10 .88

M & L for Construction of septic tank including excavation in any type of strata, foundation in PCC 1:2:4 type B-1 ( using 20 mm graded stone aggregate ) brick work in CM 1:4, RCC Slab cover including RCC Precast manhole cover having 6mm plate embedded all around/fibre reinforced cover with angle iron frame vent shaft and sludge chambers complete for 25 users all as specified and shown on Drg Nos CEPZ/ 88 TD /17-M Sheet Nos 1/4; 2/4 ,3/4 and 4/4 dated 01.10 .88

S & F in repairs PVC valve less, syphonic action type, flushing cistern 10 ltrs capacity, low level, white, with inlet, ball valve, float and handle, including brackets etc complete all as directed.

S&F in repairs 15mm size fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed etc complete all as directed.

S&F in repair15mm boreTubes, `medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S&F in reapir 20mm boreTubes, `medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S&F in reapir 25 mm boreTubes, `medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Cutting chases in Stone, concrete block or slab walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth all as specified and as directed.

S&F in repairs 5mm thick mirrors with fixed with stainless steel bolt & nut and fixed to brick/stone masonry walls built in cement mortor etc complete all as directed.

Cutting into road/ black top/PCC pavement of any thickness including excavation in any type of soil upto 0.50m to 0.80m width and 0.50m to 1.50m depth, refiling, compaction of soil after laying of PCC bed, haunching and pipe, packing and compaction with existing soling/GSB/WBM/WMM, and top surface prepared with 0.15m thick cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) complete all as specified and as directed.

Cutting into existing manholes for removing existing branch drain, making good to pipe and rendering cutting out branch channel, and making good benchings complete all as specified and as directed.

Taking up or down 15mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and as directed.

Taking up or down 20mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and as directed.

Taking up or down 25mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and as directed.

S&F 15mm boreTubes, `medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S&F 20mm boreTubes, `medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S&F 25mm boreTubes, `medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Note: Amount of sch of credit of Rs.77317.86/-will be deducted from total amount of BOQ.

J Sams Contructions (BID ID -3062620)

M/S Chandan Construction Company (BID ID -3062556)

GILL BROTHERS CONSTRUCTION (BID ID -3062094)