TP1-41/2025-26 OF CE/TP-I/CNI

Amount

Earth work excavation for foundation including all labour charges including initial lead,labour, lift, etc. complete.

Supplying and filling with good river sand for foundation including cost of sand, all labour, lead,lift, consolidation etc. complete.

PCC 1:3:6, with 20mm HBG metal without form work including cost of all materials, cement, all labour, lead, lift, etc. complete.

Providing RCC 1:1.5:3 raft using 20 mm HBG metal without form work including cost of all material, lead, lift, etc., complete but excluding cost of all respects

Providing RCC 1:1.5:3 using 20 mm HBG metal with formwork including cost of all material, lead, lift, etc., complete but excluding cost of all respects

Providing PCC 1:2:4 using 20 mm HBG metal with out form work including cost of all material, lead, lift, etc., complete but excluding cost of all respects

PCC 1:2:4, with 20mm HBG m/c metal with form work above GL including cost of all materials, cement, all labour, lead, lift, etc. complete.

Supplying, fabricating and placing in position of steel reinforcements including cost of steel,binding wire, labour, lead, lift etc complete as per standard specification and as directed by the dept. Engineer at site

Supplying and spreading of well gravel for low lying area including cost of well gravel, labour for consolidation, lead, lift, etc. complete.

Brick work in CM 1:5 using II class bricks of size 9" x 4 3/8" x 2 3/4 " including cost of all material, lead, lift, labour, etc, complete.

Brick work in CM 1:6 using II class bricks of size 9" x 4 3/8" x 2 3/4 " including cost of all material, lead, lift, labour, etc, complete.

Plastering with CM 1:3-12mm thick for wall both interior and exterior faces including cost of all materials lead lift etc complete.

Plastering with cm 1:5 mix using 12mm thick for inside and outside walls, plinth protection including cost of all materials,labour,lead, lift etc complete

Colour washing two coats using white cement mixed with approved colouring pigments, including cost of all materials, labour, lead, lift, etc. complete.

Fabrication and supplying of 20mm dia foundation Bolt and nut of length 1.20m,threading for a length of 15 cm at top and hot dip galvanising of bolt including supply of 2 nos of GI nuts and washers and fixing in the position as directed by the engineer at site including assembling of template etc., cost of template, all material, labour, lead, lift etc., complete

Fabrication of Template and assembling in correct position for various equipment plinth and grouting the foundation bolts including cost of all materials, labour, lead, lift etc. complete.as directed by the dept. Engineer at site

Supplying and spreading of Quarry dust filling including cost of all material, labour for spreading all labour ,lead, lift, etc. complete.

Supplying and spreading of 20 mm HBG metal (machine broken ) including cost of all material, labour for spreading all labour ,lead, lift, etc. complete.

Supplying and fixing of 15 MM DIA PVC PIPE (with Labour ) ISI branded and approved quality as indicated below for water line , sanitory line etc.including cost of PVC special , and all other materials etc.complete as per standard specification.

Supplying and fixing of 25 MM DIA PVC PIPE (with Labour ) ISI branded and approved quality as indicated below for water line , sanitory line etc.including cost of PVC special , and all other materials etc.complete as per standard specification.

Supplying and fixing of 20 MM DIA PVC PIPE (with Labour ) ISI branded and approved quality as indicated below for water line , sanitory line etc.including cost of PVC special , and all other materials etc.complete as per standard specification.

Supplying and fixing GM wheel valve of 25 MM DIA approved brand (leader ) ISI quality including cost of all materials, labour etc.complete

Supplying and fixing GM wheel valve of 20 MM DIA approved brand (leader ) ISI quality including cost of all materials, labour etc.complete

Labour charge for supplying and fixed of approvad quanty MS rails (90 LBS)including cost of all materials labour transport lead Etc.

Supplying and fixing of MS angle for Cable duct including cost of metal ,labour all lead and lift etc . Complete.as per standard specification and as directed by the dept. Engineer at site

Supplying and fabrication and fixing in position of anodised aluminium natural colour matt finish sliding window of size 1.18*1.48 m in two track in all floors with following sizes. All the two shutters with slinding arrangements, the bottom section should have Gutter arrangements so as to drain the water entering and made with extruded aluminium section of outer frames as shown below with necessary accessories such as rubber beading , handle,fixing 4mm thick clear sheet glass including all required for fabrication etc. complete. Necessary dimantling making holes in RCC columns , beams, masonry wherever necessary with power drill to the extent required and made good to the original condition after fixing as directed by the dept.Engineer. The Al. surface is to be anodised with matt finish under electrically controlled condition in accordance with ISI 1868/1962 specification for an average anodic film thickness of not less than 15 microns. ( All materials should be got approved by the Executive Engineer) before fixing in position.

M&F in position of anodised aluminium partially glazed single leaf door using outer frame 101.60 x 44.45 x 2.10mm @ 1.608Kg/M and door inner frame side and vertical 53.70 x 44.45 x 2.30mm @ 1.238 Kg/M, door bottom section 83.50 x 44.45 x2.40mm@ 1.679Kg/m and diveder and top of door frame 47.62 x 44.45x 2.17 mm@ 1.072 Kg /M glazing clips of 17.30 x 19.0 x 0.60mm @ 0.083 Kg/M, rubber beedings, hinges, handle, hydraulic floor spring, automatic door closer etc, and with 12mm tk. one side laminated board at bottom half portion and top half portion with 5mm thick sun cool glass including cost of all materials, lead, lift, etc, complete Single leaf door 1.20 x 2.20 m

Paving the control room floor with 600x600mm vitrified core endura floor tiles (Industrial type floor of johnson endura make , quality, colour and shade as directed by the engineer at site) in all floors over a base layer of cement mortar 1:3 (one cement and three sand) 20mm thick laid in-situ and pointed with same coloured cement mortar neatly finished as per standard specification .

Painting 2 coats using white cement over one coat of priming coat for ceiling in all floors and exposed faces of beams including cost of all materials and scaffolding etc. complete.

Painting 2 coats with Asian ACE or equivalent over one priming coat of cement paint over cement plastered wall surface, ceiling and other new surface and including cleaning ,preparing the surface and curing etc.complete.

Painting new iron works with two coats synthetic enamel paint over one coat of primer including cost of all materials , lead,lift etc complete.

Wiring with 2x1.5sqmm (22/0.3) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with MS switch box and 5A F.T. Switch in flush with wall and covered with hylum sheet of 3mm thick with painting of suitable colour continuous earth wire connection of 14 SWG TC wire for light point / Fan point or Electronic Regulator.

Supplying and fixing box type 4'-40w single flouresent fitting complete with copper choke and condenser 1 no 4'-40w tube with t.w. round block on wall or ceiling with pvc unsheated leads from terminals to the fittings with tube

Supplying and fixing of 1400mm sweep ac ceiling fan wit regulator with 300mm down rod on the exisitng clamps of approved make and colour including cost of all materials lead, lift etc., complete.

Supplying and fixing of water tight Bulk head fitting with guard and approved suitable make for incondescent lamp with guard and 100 w bulb.

Fabrication, supplying and erection of M.S. grill for ornamental gate, windows as per standard specification approved by the engineer at site including cost of all materials, welding, painting with two coats of enamel paint over one coat of red oxide primer including cost of all materials, labour, lead, lift, etc. complete.

Refilling in foundation with excavated earth in layers not more than 15 cm thick well rammed and watered consolidated etc complete as per standard specification

Transporting the surplus excavated earth, debris etc away from the site to a lead of 5km including cost of all lead, lift, conveyance , loading, unloading etc.complete

Providing Antitermite treatment in four stages i) Immediately after ewe and before laying of foundation concrete ii) After refilling sides of foundation iii) Before laying of foundation concrete and outside of basement upto 1m alround the building

Providing weathering course with one course of pressed tiles of size 23*23*2 cm embedded in cm 1:3 12mm thick and pointed with same mortar mixed with crude oil 10% weight of cement used over bed of brick jelly,lime concrete of 80mm thick with ratio of 32:12.5 and well beaten with wooden hammers spraying lime mortar, kadukkai and jaggery solution as per standard specification including cost of all materials ,labour, lead ,lift etc complete.

Dismantling Brick/Stone masonry in cement mortar wall work and clearing away and removal and disposal of debris and Rubbish 5KM away from the site including cost of all equipments, labour,lead,lift etc., complete as instructed by Engineer at site

Dismantling of RCC by manual/by using deploying machineries and clearing away and removal and disposal of debris and Rubbish 5KM away from the site including cost of all equipments, labour,lead,lift etc., complete as instructed by Engineer at site

Dismantling of Pressed Tiles and weathering course and clearing away and removal and disposal of debris and Rubbish 5KM away from the site including cost of all equipments, labour,lead,lift etc., complete as instructed by Engineer at site

GST for bidders within TamilNadu

GST for bidders outside TamilNadu (IGST)

H.Venkateswaran (BID ID -1395245)