Extension of Dining Hall including Providing of Tiles, False Ceiling in the Room No. 4 and 5 entrance Dining Hall Lobby etc of Ground Floor of Guest House and Providing S S Railing for Guest House of AGBP NEEPCO Bokuloni Dibdrugarh Assam

Amount

Dismantling and removing the existing door and window frame (chowkath) both wooden and steel of different sizes without damaging the walls and removing the frame and necessary repairs to the edges of the walls as directed for all levels. (i) Area of door / window upto 3.00m2

Demolishing brick work including stacking of serviceable materials and disposal of unserviceable materials as directed for all levels.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing, steps, walls, brick works etc. as directed and specified including dewatering if necessary and curing complete (shuttering where necessary shall be measured and paid separately). (a) In prop. 1 : 3 : 6 (1 cement : 3 coarse sand : 6 coarse aggregrate by volume

Supplying, fitting and fixing in position reinforcement bars conforming to relevent I.S. code for R.C.C. work / R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chair, spacers etc. complete (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (upto 1st floor level). a) From Primary Producer: TATA / SAIL / Jindal Steel / Shyam Steel / RINL (i) TMT Corrosion Resistant Steel (CRS) reinforcement bar.

Providing and laying plain/reinforced cement concrete works cement with coarse sand and 20mm down graded stone aggregate including dewatering if necessary and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid seperately) (I) Using mixture machine. A) In superstructure from plinth level up to 1st floor level (ii) Column, pillars, post, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing) including preparing the top surface and finishing of nosing. B) Without using admixture, plasticiser (a) M15 grade concrete or Prop. 1:2:4

Providing form work of ordinary timber planking so as to give a rough finish including centring, shuttering, strutting and propping etc., height of propping and centring below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in. Flat surface such as soffits of suspended floors, roofs, landings, cantilever slabs, chajjas, balconies and the like. (a) Floors etc. up to 200mm in thickness. (i) Using 25mm thick plank

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth upto 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement morter and will be measured and paid separetely) (A) 112 mm thick brick wall (a) In cement morter in propotion 1:4 (1cement : 4 sand)

Supplying and installing uPVC- Sliding Windows made out of Lead free, UV resistant green profile of BIS standard uPVC multichambered sections of with corners fusion welded, fully reinforced with galvanized steel atleast 1.5 / 2 mm thick including interlock profile, glazing bead, grooving bead, brush seal, aluminium sliding track, stainless steel rollers, sealing wedge block, Espag, into handle, pop up handle, keeper, drain cap fisher screws, packing pieces with all necessary stainless steel screws etc. complete as directed. The windows must be installed complete with all kinds of ironmongery including EPDM gaskets, bridging wedges and glass packers and with suitable water drainage system. Application of Silicon sealant from inside / outside of dowcorning / GE or equivalent complete as directed. With 5mm clear glass. a) 2 track sliding Window with Flyscreen using uPVC section of minimum sizes 88mm x 50mm x 2.4mm thick wall for frame with inbuilt flyscreen track, 37mm x 61mm x 2.4 mm thick wall for glass sash. 25mm x 49mm x 2.4mm thick wall for flyscreen sash and Interlock: 43mm x 23mm (Glass Panel) ( WINSTA/KOMMERLING/FENESTA/FENCRAFT) (I) 2-Panel with 5mm clear float glass. (WINSTA KOMMERLING / FENESTA / ENCRAFT) (i) 2-Panel with 5mm clear float glass

Providing, fitting & fixing M.S. grill of required pattern for windows/clearstory windows/ openings with M.S. flats at required spacing in frame all round, square or round M.S. bars. With round headed bolts and nuts or screws. i) Ornamental grill. (a) Fixed to steel frames.

10mm thick cement plaster in single coat on fair side of brick/concrete wall for interior plastering up to Ist floor level including arises or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. a) In cement mortar 1:4

Painting one coat (excluding priming coat) on old wood and wood based surfaces with enamel paint to give an even shade including cleaning the surfaces of dirt, dust and other foreign matter sand papering and stopping. i) Surface over 100 mm in width or girth. a) High gloss (Asian paint / Berger paint / ICI paint/ J&N paint / Nerolac)

Painting two coats (excluding priming coat) on new steel and other metal surfaces with enamel paint of approved brand and manufacture(Asian paint / Berger paint / ICI paint / J & N paint / Nerolac) to give an even shade including cleaning the surfaces of dirt, dust and other foreign matters. i)Surface over 100mm in width or girth. a)General purpose (Asian paint / Berger paint/ ICI paint/ J&N paint / Nerolac)

Providing and laying machine made clay roof tiles on sloping roof and chajjas over 20mm thick base of cement mortar 1:3 and jointed with grey cement slurry and joints flush with mortar 1:3 complete.

Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 8mm on floors, skirtings, risers and treads of steps over 15mm thick base of cement mortar in prop. 1:3 (1cement : 3 coarse sand) including cutting where necessary finished with flush pointing with Fix-A-Tile Choksey/ Sika/ Pedelite/ Rouf/white cement slurry mixed with approved pigment to match shade of tiles, complete at all levels as specified & directed. (Coloured pigment should be in confirmity with colour of tiles and as approved by the Department). a) Normal range (Somany /Orient/Nitco/ Asian Make) i) Of sizes 600 mm x 600 mm and above

Providing polished vitrified wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10mm thick in prop. 1:3 (1cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile ( Choksey/ Sika/ Pedelite/ Rouf/ white cement slurry) mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Coloured pigment should be in confirmity with colour of slab and as approved by the Department). (walls mean both interior and exterior walls). i) Of sizes 300mm x 600mm and above

Supplying, fitting and fixing and painting where necessary (one coat primer and two coats of paint) M/F suspended Ceilling which includes G.I.perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceilling, screw fixed to brick wall/ partition with the help of nylon sleeves and screws, at 610mm c/c.Then suspending G.I intermediate channel of size 45mm (0.9mm thick with two equal flanges of 15mm each) from the sofit at 1220mm c/c with ceiling angle of width 25mm x 10mm x 0.55mm thick fixed to soffit with G.I.cleat and steel expansion fasteners. Ceiling section of 0.55mm thickness having knurled web of 51.5mm and two equal flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clip and in direction perpendicular to the intermediate channel at 457mm c/c, 9.5mm/ 12.5 mm tapered edge Gypboard (confirming to IS:2095-1982) is then screw fixed to ceiling section with 25mm long drywall screws at 230mm c/c. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally, the boards are to be jointed and finished so as to have a flush look which includes filling and finishing the tapered and square edges of the boards with jointing compound, joint paper tape and two coats of drywall topcoat suitable for Gypboard complete at all levels as specified and directed.(For light fittings, providing opening for doors, windows, ventilators etc. cut out made with frame of perimeter channel supported suibly to be measured and paid seperately where necessary). (i) 9.5 mm thick.

Providing two coats of J. K Wall Putty (White cement based putty for concrete / mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm)

Applying one coat of alkali resistance primer of approved brand and manufacture on wall after thoroughly brushing the surfaces free from mortar droppings and other foreign matters including preparing surface even and sand papered smooth.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J &NA paint/ Nerolac ) on new surface to give an even shade after throughly brushing the surface free from mortar droopings and other foreign matter and sand papered smooth. (i) Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Providing polished granite slab of approved quality, size and shape and thickness not less than 18mm on floors, skirtings,treads and risers of steps over cement mortar bed 15mm thick in prop.1:3 (1cement : 3 coarse sand) including cutting where necessary, finished with flush pointing with Fix-A-Tile Choksey/ Sika/ Pedelite/ Rouf)/ white cement slurry mixed with approved pigment to match shade of granite slab, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately).(coloured pigment should be in confirmity with colour of tiles and as approved and directed by the Department) (i) Normal Quality (i) Fix-A-Tile (Choksey / Sika / Pedelite / Rouf)

Providing polished granite tiles of approved quality, size and shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 15mm thick in prop. 1:3 (1cement : 3 coarse sand) including cutting where necessary, finished with flush pointing with Fix-A-Tile Choksey/ Sika/ Pedelite/ Rouf)/ white cement slurry mixed with approved pigment to match shade of tiles,complete at all levels as specified and directed. (Cement plastering to be measured and paid separately) (coloured pigment should be in confirmity with colour of tiles and as approved and directed by the Department). (Walls means both interior and exterior walls) (A) Fix-A-Tile (Choksey / Sika / Pedelite / Rouf)

STEEL RAILING Providing fitting and fixing Stainless Steel (Grade 304) railing made of Hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i.e. fixing the railing with necessary accessories and stainles steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangment as per approved of Engineer-in-charge. (For payment only weight of Stainless Steel member is to be considered. No extra payment for fixing accessories such as nuts, bolts, fasteners etc. will be considered).

Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered ply wood face panels conforming to relevent I.S. code including oxidised iron butt hinges (100mm x 75mm x 3.5mm) 6 Nos. with necessary wood screws. a) One face decorative and other face non decorative type and block board core. (i) 25mm thick

Proving and fixing Chlorinated Polyvinayal Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and bruss threaded fitting including i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes. (A) Concealed Pipe with cutting chases and making good the walls. i) 20mm nominal dia pipes.

Providing fitting and fixing Decorative Mirror complete as directed and specified. (A) Parryware Make (a) Size 800 x 600mm

Providing vitreous China wash basin with CI/MS brackets, CP brass chain with plug, PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required (Pilar cock, stop cock waste coupling are to be paid separately) Table Top Basin a) Jaquar make (i) Solo (Cat. No. SLS-WHT-0558)

Providing, fitting and fixing PVC pipes of 6 KG/cm2 (Supreme/Prince) or other ISI approved including joining, fitting and fixing with clamps etc. necessary complete at all levels including below G.L as directed and specified. a) Concealed by chiseling or breaking brick wall / C.C./R.C.C and making good to the damages. (i) 75mm dia.

Supplying fitting and fixing chrome plated (C.P.) stop-cock of approved brand and size as mentioned below as directed and specified. (G.I. & C.P. pipes will be measured separately) Jaquar (a) Queen's collection / The Stealth Rangers (For VIP use). Prior approval of Chief Engineer PWD (Bldg) must be taken before use) (i) Angular stop cock with wall flange

Supplying fitting and fixing C.P. pillar cock of 15mm dia of approved brand as specified and directed. Jaguar make (a) Long neck with areator

Bidder Name

Amount in Words

R M ASSOCIATE

RAHUL ENTERPRISE

LAMBIT CHETIA

ANUPAM SAIKIA

RISHIK CHARAN SARMA

LAMBIT CHETIA

R M ASSOCIATE

RAHUL ENTERPRISE

RISHIK CHARAN SARMA