SPECIAL REPAIRS TO BLDG NO.T-6 AT ATS BELAGAVI

Amount

Dismantling Asbestos cement (corrugated, semi-corrugated etc) sheets in roof coverings complete all as directed

M & L pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. (Note :- The length of self tapping screw may vary for wooden and steel truss. Contractor to quote rate accordingly.)

M & L pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in ridges, roof overing/cladding to wall, fixed with self tapping screws complete all as specified and as directed. (Note :- The length of self tapping screw may vary for wooden and steel truss. Contractor to quote rate accordingly.)

Dismantling of Mangalore pattern or similar tiles in roof coverings including ridges all as directed.

Taking down of Battens for tiles, shingles etc., of any size including tilting fillets spacing exc 15 cm all as directed.

Dismantling timber scantlings 40 sq cm and over in section and in any position in framed work all as directed.

All as per item No. 6 above but unframed work all as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.,) or insulation boards/slabs/blankets, any thickness including cover fillets/iron frame work etc. all as directed. (Note : Angle/FI/'T' sections etc., obtained from dismantling to be considered as schedule of credit under scrap iron).

M & L for powder coated Aluminium snap grid (minimum 50 microns thickness powder coating) of size 605 x 605 mm with anodised aluminium angle of size 25mmx25mm x1.5mm thick and main & cross 'T' of size 40mm x 25mm x 1.5mm thick for false ceiling including fixing of supporting hangers all as specified and directed . Note :Cost of hangers will be measured & paid seperately under relevant items of this schedule.

S & F Hangers 6 mm dia GI (up to 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia 40 mm long complete all as specified.

S & F 12 mm thick Gypsum board of size 600 x 600 mm in ceiling fixed with screws and finished with two coats oil bound distemper over a coat of self primer all as per manufaturers instructions complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as directed.

S & F Roof trusses (framed), trussed purlins, rails and fastenings and heavy brackets framing including distance pieces, cleats etc Fe 410-W (Gde E-250) quality-B all as specified and directed

Demolition of cement concrete (un reinforced) of any description and in any position not otherwise specifically provided for all as directed.

M & L Providing plain cement concrete type C1, 1:3:6 using 20mm graded stone aggregate as in bed blocks, similar blocks , copings etc., including necessary form work complete all as directed.

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enemal paint over a coat of red oxide complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description, not otherwise described over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Surface dressing n exc. 15cm deep in hard/dense soil all as specified and directed.

Demolition of cement concrete in ground floor and pavings n exc 15 cm thick ness (below or above ground level) all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified and directed.

M&L 25 mm thick PCC 1:2:4, type B0 (Using 12.5 mm graded stone agg) as in floor finished even and smooth without using extra cement all as specified and directed.

M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tiles exc 0.11 sqm but not exc 0.18 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or cloured cement to match the shade of floor tiles including 15 mm thick cement screed bed in CM (1:6) all as specified and directed.

M & L for Coloured glazed ceramic tiles economy finish Gde B-II (b) quality of size 300 x 450 x 7 mm thick with rectified edges as in vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 10 mm thick rendering in CM (1:4) all as specified and directed.

M&L Machine cut kota stone slab flooring 20-25 mm thick over cement screed base of 20 mm thick in CM (1:4) , laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 10 mm thick rendering in CM (1:4) all as specified.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc., laid dry or laid dry and pointed in any mortar complete all as specified and directed.

M & L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4), 10mm thick, including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as specified and directed.

M & L for 20mm thick Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing including moulding half round all as directed, in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as specified and directed.

M & L for green marble 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing, including moulding half round all as directed, in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed.

M & L for green marble for wall lining (veneering to wall) 25mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with marble shade including moulding half round all as directed, of complete all as specified and directed.

M & L for Machine cut cudappa stone slab 20-25mm thick over 20mm thick cement screed base laid in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Rubbing and polishing to existing kota stone, including waxing to remove all stain, dirts/soil marks etc., all as specified and directed.

M&L 75mm thick PCC 1:3:6, type C2 using 40mm stone aggregate as in plinth protection finished even and fair without using extra cement all as specified and directed.

M&L for forming 12mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade 'A' as in 75mm thick plinth protection complete all as specified and directed.

Taking down of chowkats with shutters (without taking off shutters from the frames) n exc 1.5 sqm each all as directed.

Taking down of chowkats with shutters (without taking off shutters from the frames) exc 1.5 sqm and n exc 4 Sqm each all as directed.

Taking down shutters of any description n exc 1 sq.m each and refixing in same opening complete all as directed.

Taking down shutters of any description exc 1 sq. m and n exc 2 sq. m each and refixing in same opening complete all as directed.

S&F Pressed steel frames for doors 125x60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified.

S & F for second class hardwood for plain, solid, straight chowkats and frames, wrought, framed debated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified.

S & F for 35 mm thick second class hardwood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather eged), or of veneered particle board medium density, wood particle board witn commercial face veneers; supplied and fitted to chowkats complete all as specified and directed.

M & L for 2nd class glazed and skeleton shutters, 35 mm thick, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauze etc; sizes of members of shutters as specified in SSR Part I, section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed.

M & L for 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides fitted to chowkats completed all as specified and directed.

M&L for factory made solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling and fixing in opening as per specification and drawing complete all as specified and directed.

S & F for factory made solid PVC moulded door shutter, 28 to 30 mm thick (stiles) with 2, 4 or 6 raised panel design with 2 mm thick moulded PVC sheet on the front face and 2 mm thick plain colour PVC sheet on back face , supplying and fixing in frame at site as per specification & drawing with particle board core complete all as specified and directed.

S&F powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc., including powder coating (minimum thickness of Powder coating 50 micron) complete all as specified and directed.

S&F powder coated aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc., including powder coating of any colour (Thickness or powder coating not less than 50 micron) complete all as specified and directed.

S&F Anodised aluminium window and ventilator shutters, fixed/ sliding type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc., including powder coating of any colour (Thickness or powder coating not less than 50 micron). complete all as specified and directed.

S&F 5.5 mm thick sheet glasss, ordinary quality and glazing with oil putty or fixed in aluminium section in square exc 0.5 sq. m in each pane complete all as specified and directed.

M & L 12mm Pre-laminated particle board, interior grade, prelaminated both sides with decorative choice laminations, fixed with screws to aluminium frame work complete all as specified and directed.

S & F Aluminium (Die cast) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S & F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed.

M & L for Mild steel work as in hold fast, wall ties and wind tie bands, straps or similar small articles conforming to Fe-290 Gde E-165 etc., complete all as specified and directed.

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or steel screws all as specified

Supply and fixed in repairs stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or steel screws all as specified

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed.

S&F 3.0 mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F 140 mm overall length of cover plate floor door stopper of aluminum alloy body and tongue, anodised with hard drawn steel spring fixed in floor complete all as specified and directed.

S&F 200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S & F Butt hinges 100 mm long medium Weight cold rolled of mild steel complete all as specified and directed.

S & F for 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, stapple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F 300 mm, Mild steel ordinary rat tail rod pattern springs including roller and roller plate complete fixed to MS frame or wooden frame complete all as specified and directed.

S&F 150 mm long extruded aluminium anodised handle fabricated type complete all as specified and directed.

S&F in repairs harrison rails, mild steel,chromium plated with fixing brackets,stops, rollers etc., all as specified and as directed.

M&L for preparation of new wooden surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enemal paint over a coat of pink primer complete all as specified.

M&L for preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

Taking down cement plaster on brick or stone walls, etc., including racking out joints, hacking for key, scrubbing down with water etc., and removal of debris to a distance not exc 50 mtrs and depositing where directed.

M&L for 15 mm thick cement plaster in CM (1:4) for wall finished even & smooth all as specified and directed.

Material and labour for 15 mm thick cement plaster in CM (1:6) for wall finished even & smooth all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over wall care putty 1-2 mm thick in two layers on walls all as specified and directed

M&L for preparation of new plastered surfaces of walls and applying two coats of anti fungal paint over a coat of primer all as specified and directed.

M&L for preparation of old plastered surfaces of walls and applying two coats of white wash on walls complete all as specified and directed.

M&L for preparation of old plastered surfaces of ceilings and applying two coats of white wash complete all as specified and directed.

M&L for preparation of old plasterd surfaces of walls by complete removal of existing treatment including washing, rubbing and cleaning and applying a coat of primer and two coats of antifungal paint all as specified and directed.

M & L for complete removal of existing treatment of old surface of wall by scrapping and washing including preparation of surface by applying a 3mm thick thin layer of wall care putty (JK or Birla) and applying two coat of oil bound distemper all as specified and directed

Taking up/down 15mm bore steel tubing and connection, including cleaning for refixing or removal to store all as specified and directed

Taking up/down 20mm bore steel tubing and connection, including cleaning for refixing or removal to store all as specified and directed

Taking up/down 25mm bore steel tubing and connection, including cleaning for refixing or removal to store all as specified and directed

S & F 16mm bore CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed.

S & F 20mm bore CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed.

S & F 25mm bore CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed.

S&F in repair 15mm bib taps fancy type chromium plated round handle, screwed down, screwed for iron pipe all as specified and directed.

S&F in repair 15mm stop valves fancy type, chromium plated, screwed down, high pressure, with crutch or round handle, screwed both ends for iron pipe or for unions all as specified and directed.

S&F 15 mm dia pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe all as specified and directed. '

S&F swivel shower of PTMT any colour for fixing with 15 mm pipe (minimum weight 40 gms) all as specified and directed.

S&F tubular brass chromium plated Towel rail 20 mm dia D type 60 cm long between flanges all as specified and directed.

S&F in repairs soap dish, vitreous china white, apoproximate size 160x160x90mm, fixed to plugs with chromium plated brass screws all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts of length 450mm all as specified and directed.

S&F in repairs vitreous china squatting pan, 'Orissa' pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern) including taking down old water closet and provision of cement concrete bedding etc., complete all as specified and directed.

S&F in repairs vitreous China Urinal, half stall type, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe, 32mm size/bore flushing pipe and waste coupling all as directed by Engineer-in-Charge.Make-Hindustan/Cera/Parryware.

S&F in repair PVC valve less syphonic action type low level flushing cistern 10 Ltr capacity including flange valve handle, Bracket, PVC flush down pipe length upto 1.3 m height, dia as required with bend including taking down the unserviceable cistern all as specified and directed.

S & F Vitreous china wash basin, white, flat back, size 550X400mm including, waste coupling , pipe and cutting for and pinning in ends of brackets or erecting stand brackets all as specified and directed.

Dismantling water tanks of capacity exc 1000 ltrs and n exc 2000 ltrs complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks of 2000 ltrs capacity (cylindrical vertical with closed top) hoiseted and fixed in position all as specified and directed in SSR part I inlcuding fixing of PTMT ball valve epoxy coated aluminium rod and high density plastic ball of 20 mm dia or equivalent as per site condition all as specified and directed.

Excavation in trenches n exc 1.5 m wide and n exc 1.5 m depth in hard/dense soil for foundation etc., or for shafts, wells, cesspits, manholes, pier holes etc., n exc 10 Sqm on plan and n exc 1.5 m in depth and getting out complete all as specified and directed.

PCC (1:4:8) type D2 using 40 mm graded stone aggregate as in foundations, filling and mass concrete all as specified and as directed

M & L for pre cast cement concrete block masonry type C1, 1:3:6 (20 mm graded stone aggregate) solid block exc 10cm in width having minimum compressive strength of 50 kg/sq cm as per IS 2185 (Part I) 2005 and set in cement mortar 1:4 complete all as specified and as directed

M & L for preparation of newly plastered surfaces and applying two coats cement based paint over a coat of self primer on walls, pillasters, cornices, etc., all as specified and as directed.

TMT bars of 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Use and waste formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping and similar work all exceeding 20cm wide rough finished flat concrete surfaces complete all as specified and directed.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceedings 200mm thick (Horizontal or sloping) of rough finished flat concrete surfaces complete all as specified and directed.

M & L reinforced cement concrete 1:2:4 (nominal mix) type B1, (20 mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like bands in walls complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/dense soil all as specified and directed.

Removing excavated material (Soils) not exc 50 m and depositing where directed at a level n exc 1.5 m above the starting point all as specified and directed.

S & F stop valves 20 mm bore, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron iron pipe or for unions complete all as specified and as directed.

Supply and laying of CPVC pipes of 20 mm outer dia SDR 11 and plain CPVC SDR 11 fittings in trenches complete all as specified and directed

Surface excavation n. exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed.

M & L for broken stone or boulders hardcore gauge n exc 63 mm, deposited, spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for 75mm thick cement concrete 1:4:8, type D-2, (40mm graded stone aggregate) complete all as specified and directed.

M & L for 100mm thick cement concrete 1:2:4, type B-1, (20mm graded stone aggregate) finishing cement concrete and finishing the surface even and fair without using extra cement complete all as specified and directed.

M & L for Rubber moulded cement concrete tiles 25 mm thick,any size and any colour as approved by GE, set, jointed and pointed in neat cement slurry in floors with grey cement and no pigment over 15mm thick screed bed in CM (1:6) complete all as specified and directed.

Excavating over areas, n. exc. 1.5 m deep and getting out in hard/dense soil complete all as specified and directed.

M&L Precast cement concrete 1:2:4, type B1 (using 20mm graded stone aggregate) for manhole cover slabs etc., setting in cement mortar(1:4) as specified and directed

Demolition of brickwork or stone/boulder masonary, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc., but excluding ashlar facings, dressed stonework and precast concrete articles all as specified.

M & L for pre cast cement concrete block masonry in 1:3:6, type C1, (20 mm graded agrregate) solid blocks not exc 10cm in width having minimum compressive strength of 50 kg/sq cm as per IS 2185 (Part I) 2005 and set in cement mortar 1:4 complete all as specified

M & L for Brickwork with sub-class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in CM (1:4) complete all as specified and directed.

Extra for forming fair finished drain or channel 45 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc,.

TMT bars of 6mm to 8mm, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Demolition and breaking up drain pipes (SGSW, AC or RCC) 150 mm internal dia set in CM complete all as specified. Note :- Excavation work shall be measured and paid seperately.

M & L Salt glazed stone ware pipe, nominal dia of pipe 150 mm laid in trenches and jointed with cement complete all as specified

M & L for Cement concrete 1:4:8, type D-2 (using 40mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe. complete all as specified

M & L for Cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in benching and forming channel inside manholes for section of pipe 100mm, 150mm or 200mm including finished even and smooth using extra cement complete all as specified

M & L Providing precast cement concrete louvres and jallies, 35mm thick (measured solid), set in CM (1:4) type B0, 1:2:4 (12.5mm graded aggregate) including all mouldings but excluding frame (Pre cast frame shall be measured separately) complete all as specified and directed.

Removal of concrete and plaster debris to a distance 5 Km and depositing where directed at a level n exc 1.50 m above the starting point complete all as specified and as directed.

S & F Vitreous china wash basin white oval type of size 550X400mm including, waste fittings 32mm dia, pipe and cutting for and pinning in ends of brackets or erecting stand brackets complete all as specified and directed.

Supply and fix PVC connection 15mm size with PTMT nuts of length 450mm all as specified and directed.

S&F for 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed in wall/floor/trenches with necessary clamping where required complete all as specified and directed.

S&F for 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed in wall/floor/trenches with necessary clamping where required complete all as specified and directed.

S&F for 50 mm dia Polyethylene pipes (HDPE) of pressure rating 6kgf/cm2 laid in trenches/wall/floor complete all as specified and directed.

S&F PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm dia inclduing fixing to existing pipe properly all as specified and directed

S&F PVC (SWR) bends for 110 mm bore pipe with access door all as specified and directed

S&F PVC (SWR) bends for 75 mm bore pipe all as specified and directed

S&F 110mm PVC (SWR) junction single, (Single T) equal or unequal all as specified and directed

S&F 75mm PVC (SWR) junction single, (Single T) equal or unequal all as specified and directed

Supply and fix PVC stop valve 75mm bore all as specified and directed

S & F Aluminium, Stainless Steel Roof Top Air Ventilators Continuously in motion with low noise and leak proof installation with following specifications upto height of 10M including necessary scaffolding as applicable and match the profile of sheet to be cut and make sure there is no leakage from affected roof portion with the following specification for totally aluminum built complete all as specified and directed (i)Number of Vanes: 0.5 mm thickness, 38 Numbers (ii)Center Shaft: Stainless Steel (iii)Bearing: Self Lubricated - 2 Nos (iv)Rivets: Aluminum Pneumatic Rivets (v)Turbine Doom Thickness: 1 mm (vi)Turbine Outer Dia: 680 mm (vii)Turbine Doom Dia: 380 mm (viii)Turbine Rotor Dia: 655 mm (ix)Turbine Throat Dia: 610 mm (x)Turbine Height: 360 mm (xi)Turbine Weight: 3.750 Kgs

Cutting the existing corrugated GI sheet or AC sheet or Mangalore tiles roofing upto 600 mm dia upto 10M height for fixing of air ventilator including silica joints to the periphery making water proof complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc all as directed.

Taking down carefully unserviceable main switches/DB's off size from their position and removing materials from site all as specified and as directed by Engr-in-Charge

Taking down existing sub main wiring with aluminum conductor cable of 2 runs of 4/6/10 sqmm with GI earth wire on and including wooden batten and removing materials from the site and making good distrubed surface of walls and and roofs complete all as specified and as directed by Engr-in-Charge

Taking down carefully unserviceable tube light fitting from it's position complete all as specified and as directed by Engr-in-Charge

Material and Labour for point wiring with PVC unsheathed multi standard 1.5 Sqmm FRLS copper Cable drawn in and including PVC casing capping 20/25 mm width complete with all accessories including 1.6 mm thick pressed steel terminal boxes with 3 mm thick plastic laminated sheet cover for fixing switch,socket ,regulator etc of suitable size to be fixed on wall respectively including white washing/colour washing/distembering to match the disturbed surfaces including PVC unsheathed multi standard 1.5 Sqmm FRLS copper Cable as earth continuvity connected with common earth dolly complete for One light point controlled by one, one way switch 5 Amp complete all as directed

All as per item No 146 above but for one fan point controlled by one, one way switch 5 Amp all as specified and as directed.

All as per item No 146 above but for one 3 pin switch socket outlet 5 amp independent all as specified and as directed.

All as per item Sl No 146 above but for one 3 pin socket outlet 15 Amp independent with cable of size 2.5 Sqmm for piont wiring and 2.5 sqmm as in contineous earth wire all as specified and as directed.

M&L complete for switch piano flush button single pole one way 5 Amp 240 V all as specified and as directed.

M&L for switch socket combination 2 in 1,3 pin 5 Amp flush type 240 volts complete all as specified

M&L for switch socket combination 2 in 1,3 pin 16 Amp flush type 240 volts complete all as specified

M& for ceiling rose surface backelite three terminal 240 volts complete all as specified

S&F fan regulator, electronic, step type , flush mounting complete all as specified and as directed.

Supply and Fix REGAL Batten for LED tube with single LED Lamp 1x 20 w, Ultra bright glass LED Tubelight with very high efficacy suited for installation in T5/T8 fitting with lamp holders etc. complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size all as directed Make & Model No for Batten :CROMPTON Cat No Regal LED Batten Cat No DIJB12LT8-20and LED Lamp LED Lamp Crompton Cat No LGT8-20-865-2 or equivellent model of other Make

Supply and Fix recessed type LED Light fitting 28 Watts of size 2 x 2 LED edge-lite luminaries suitable for armstrong/grid ceiling complete for low celing application with LED Drive of 28 Watts complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size all as directed Model No : Havells Cat No ENDURASLIMPROPLUS2X2PLR28/36WLED840MOD and Drivers Cat Part No. LEDDRIVER36V28WS or equivellent model of other Makes .

S&F LED building security light made of pressure die cast housing with toughened glass and high power LEDs with option of secondary optic with IP-66 protection with SPD LED street light of 20 Watt all as cat part no .LSTS-20-CDL-M of Crompton make or equivalent make of Bajaj/Philips/Wipro/Havells.with sutable size bracket made to shape of 40 mm dia GI pipe medium grade of 1.4 mtr length including MS clamps 25 x 4 mm - 02 Nos with nut bolts washers all as specified and as directed.

Sub main wiring with two single core stranded copper conductor unsheathed PVC insulated FRLS cable 1100V grade with 6 sq mm drawn through suitable size of non-metallic PVC rigid conduit/casing caping with one run 6 sqmm copper conductor FRLS cable as earth conductor and conduit accessories fixed up in surface/ recessed as required, including connecting up complete all as specified and directed. NOTE ;- Two runs of 6 sq mm cable and one run of 6 sq mm earth continuity copper conductor and one run of PVC conduit / casing caping shall be measured as one unit

M&L for MCB DB TPN 4 way with MCB as incomer with 200 Amps rated busbar 415 volts, 50 Hz with double door and TP/DP/SP MCB's as outgoing, IP-43 protection, isolated neutral bar, isolated busbar assembly,door earthing & mechanical impact strength IK 08, all as per fixing in floor/wall complete all as specified & directed.

S&F sheet metal enclosure factory made double door for DB 240 volts with 200 Amps rated bus bar SPN 8 Way complete all as specified and as directed .

M&L for MCB TPN 63 Amps 440 volts, 50 Hz AC supply complete all as specified & directed incl taking down old UNSV one.

M&L for MCB SPN 32 Amps 240 volts, 50 Hz AC supply complete all as specified & directed incl taking down old UNSV one.

M&L for MCB SP 06 to 32 Amps 240 volts, 50 Hz AC supply complete all as specified & directed incl taking down old UNSV one.

Taking down ceilng fan/ exhast fan, dismantling blades and removing fan and blades to store, Painting of fans complete in situ with synthetic enamel paint by spraying including filling cavities with filler one coat after cleaning all dust etc and refixing ceiling fan and connecting up including provision of cable from ceiling rose or connector of fan complete all as specified & directed.

M&L for Earthing complete with galvanised mild steel earth plate electrode of size 600 x 600 x 6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised ironl including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube flor watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in Electrical Plate No 3 of SSR Part-I and testing on completion all as specified and as directed.

Taking down carefully switch board along with accessories like regulator, switch socket combination, P/T switch etc from their position and relocating of switch board with accessories complete all as specified & directed.

M/s B C CHOUGULE

M/S JAYDEEP CONSTRUCTION

DHANSHRI ENTERPRISES

Phoenix Infra

ASHIRWAD ELECTRICALS

Manak landmarks

M/s. VIJAY ELECTRICALS